Mull Boot Instructions for Inswing-Outswing

Component Configuration:
Inswing Mull Boot Instructions
Inswing Mull Boot Styles:
3-9/16"
fatboy
4-3/8"
standard
4-3/8"
fatboy
4-9/16"
fatboy or
back-to-back
6-9/16"
fatboy or
back-to-back
Mull Boot Screw Locations:
3" SCREWS INCLUDED
1-5/8" SCREWS INCLUDED
FATBOY & STANDARD
INSWING MULL BOOT
CAULK GROOVE
SILL
ATTACHMENT
HOLES
MULL
ATTACHMENT
HOLE
CAULK GROOVE
SILL
ATTACHMENT
HOLES
MULL
ATTACHMENT
HOLE
SILL
ATTACHMENT
HOLES
CAULK GROOVE
SILL
ATTACHMENT
HOLES
MULL
ATTACHMENT
HOLE
SILL
ATTACHMENT
HOLES
NOTE: If sill is not
pre-drilled, drill
through sill using
mull boot sill
attachment holes as
a drilling template
Attachment
Instructions
Mull Boots are designed for
use with Endura Products'
Z-Series sills.
Inswing Mull Boot
attachment for single
mull shown.
2
4-9/16"
BACK-TO-BACK JAMB
INSWING MULL BOOT
NOTE: If sill is not
pre-drilled, drill
through sill using
mull boot sill
attachment holes as
a drilling template
6-9/16"
BACK-TO-BACK JAMB
INSWING MULL BOOT
1
Mull Prep - Convert haunched mulls to accommodate Inswing Mull Boot
Cut haunched mull to overall distance of 1-5/8" from bottom of sill to create
square cut mull bottom.
A
1-5/8"
A = Height of cut from bottom of haunched mull or back-to-back jamb.
Attach Inswing Mull Boot to Mull
3
Attach Inswing Mull Boot to Sill
Apply caulk in
caulk groove
Additional
caulking
locations
First caulk top of Mull Boot
in caulk groove as shown.
Completely fill sill
attachment holes and the
high dam kerf with caulk.
NOTE: If sill is not
pre-drilled, drill
through sill using
mull boot sill
attachment holes as
a drilling template
Finishing Instructions:
Ensure surface to be finished is clean and free of
debris, dirt or oils. Use recommended primer.
The following finishes are recommended:
Exterior latex paint, acrylic latex stain or oil alkyd paint.
Attach Mull Boot to square cut mull bottom
through mull attachment holes using 1-5/8" screw.
Wipe off excess caulk if needed.
Attach prepared mull with Mull Boot to sill through
sill attachment holes using 3" screws.
8817 West Martket St, Colfax, NC 27235 • 800-334-2006
Customer Service Fax: 336-668-4478 • Email: sales@enduraproducts.com • www.enduraproducts.com
REV.
06/25/04
Component Configuration:
Outswing Mull Boot Instructions
Outswing Mull Boot Styles:
Attachment
Instructions
4-3/8"
standard
4-3/8"
fatboy
Mull Boot Screw Locations:
3" SCREWS INCLUDED
1-5/8" SCREWS INCLUDED
Mull Boots are designed for
use with Endura Products'
Z-Series sills.
Outswing Mull Boot
attachment for single
mull shown.
1
Mull Prep - Convert haunched mulls to accommodate Outswing Mull Boot
Cut haunched mull to overall distance of 1-5/8" from bottom of sill to create
square cut mull bottom.
A
1-5/8"
A = Height of cut from bottom of haunched mull or back-to-back jamb.
4-3/8" STANDARD
OUTSWING MULL BOOT
CAULK
GROOVE
SILL
ATTACHMENT
HOLES
MULL
ATTACHMENT
HOLE
NOTE: If sill is not
pre-drilled, drill
through sill using
mull boot sill
attachment holes as
a drilling template
2
Attach Outswing Mull Boot to Mull
3
Attach Outswing Mull Boot to Sill
Apply caulk in
caulk groove
4-3/8" FATBOY
OUTSWING MULL BOOT
CAULK
GROOVE
SILL
ATTACHMENT
HOLES
MULL
ATTACHMENT
HOLE
NOTE: If sill is not
pre-drilled, drill
through sill using
mull boot sill
attachment holes as
a drilling template
Finishing Instructions:
Ensure surface to be finished is clean and free of
debris, dirt or oils. Use recommended primer.
The following finishes are recommended:
Exterior latex paint, acrylic latex stain or oil alkyd paint.
Additional
caulking
locations
First caulk top of Mull Boot
in caulk groove as shown.
Attach Mull Boot to square cut mull bottom
through mull attachment holes using 1-5/8" screw.
Wipe off excess caulk if needed.
Completely fill sill
attachment holes and the
high dam kerf with caulk.
Attach prepared mull with Mull Boot to sill through
sill attachment holes using 3" screws.
8817 West Martket St, Colfax, NC 27235 • 800-334-2006
Customer Service Fax: 336-668-4478 • Email: sales@enduraproducts.com • www.enduraproducts.com
REV.
06/25/04