508486_508487 manual.indd

Code 508486
Code 508487
1806 Bench Guillotine
1807 Floor Standing Guillotine
508486 1806 Bench Guillotine
508487 1807 Floor Standing Guillotine
AT&M: 04/08/2015
2
Technical Specification
Workning Capacity
Casting fence
Mitring Angle
45 to 90 degrees
Aluminum fence
45 degrees
Minimum length measurement
100mm
100mm
Maximum length measurement
1105mm
1105mm
Maximum normal height capacity 152mm
152mm
.Maximum possible height
157mm
157mm
Machine Dimensions
Maximum Height
1070mm
Maximum Length
1800mm
Maximum Width
420mm
Net Weight
56kg
3
4
General Description
The Mitre Guillotine is designed to give you a reliable and safe
means of producing accurate mitring with a very good surface
finish.
The major parts of the machine, which can be subject to wear
are made of Cast iron and the base or stand is fabricated from
heavy duty sheet metal.
A general view of the guillotine is shown in page 3.
The fabricated base is designed to give rigidity to the machine
and this is achieved both by the design of the base and also it’s
weight.
On the top of the base is the main table which is made from cast
iron.
At the back of the main table is the cutting head and in front of
the cutting head are fences.
The measuring table with the measuring system fits to the right
hand side of the main table.
All parts are manufactured using production tooling and the
therefore easy to replace.
5
6
7
8
Functional Description continued.
Rebate Supports
Most moldings need to be supported underneath the rebate so as
to prevent damage to the thin rebate edge during mitring.
This damage normally takes the form of splintering or tearing of
the wood or plastic.
To prevent this damage, a pair of Rebate Supports are fitted to
your guillotine.
These supports have vertical adjustment so that they can be set
to the required height of the molding rebate and they are
designed to slide along the slot in the bottom knife guides to
cope with different molding widths.
page 8 shows the Rebate Supports
Fences
Aluminum Fence : only used for 45 degrees
Casting Fences : in relation to the Mitring Head determines
what angle the molding will be mitered at.
Normally, an angle of 45 degrees is used which will produce the,
most common, 4 sides frame with each angle being at 90
degrees.
However you may require to produce 6 or 8 sided frames which
will require a different angle setting between the fences and the
Mitring Head.
The fences are therefore fitted to the main table so that they can
pivot about a central point and can be clamped at any angle from
45 to 90 degrees.
page 7 shows the Casting fences.
9
Positive pin stops
Positive pin stops are located at 45 degrees and 90 degrees.
any angle in between can be instantly set with thumb screws.
release the stop pin touch the spring
page 5 no.81、83
10
11
12
Changing the mitring blades
It is essential that the mitring blades are kept in good condition.
As soon as the finish of the mitring deteriorates or any damage
is caused to the blades they must be taken off and re ground.
Removing the Blades
Care must be taken due to the sharpness of the blades
Undo the 3 screws 020, in each blade, a spanner is provided.
Remove the top and bottom screw and then press the blade
against the Mitring Head whilist removing the third screw.
Remove the blades carefully and put them in a safe place.
Before fitting the new or reground blades
Clean the surfaces of the Mitring Head and the blades so as to
ensure that no dirt is trapped between the blades and the Mitring
Head when the new or reground blades are fitted.
13
Fitting the new blades
Fit the new blades to the Mitring Head using the 3 screws 020
but do not tighten them.
It is advisable to replace worn screws.
Ensure that the knives meet each other precisely.
1. There must be no gap between them.
2. Neither blade must protrude ahead of the other one.
3. The cutting edges must come together exactly.
Tighten the holding screws starting with the top screw in each
blade, then the middle screw and then the lower screw.
Make a trial mitre and check.
Grinding and honing the Mitring blades
The grinding and honing of the mitring blades is very important
and it must normally be undertaken by a professional saw or
tool grinder.
It is possible to ‘flat’ or ‘hollow’ grind the blades but ‘hollow’
grinding produces the best finish but only the angled surface of
the blade must be ground, not the front or back or ends.
Always have your blades ground in pairs even though only one
maybe damaged.
14
Because accidents can happen at any time, it is normal practice
to have a spare pair of blades always ready for immediate
replacement.
The cutting angle of the blade is 30 degrees.
It is essential that after grinding, the blades are honed to remove
any sharp edges and this includes honing the actual cutting edge
of the blade.
Honing not only removes any burrs but also produces a very
even cutting edge which produces the finest finish when mitring.
Always take care when handing mitring blades due to their
extreme sharpness and weight.
15
16
17
18
1806-B1 w/casting fence
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
48
PARTS
NO.
50104059
18023008
18061045
50301061
50114007
18023004
18061044
18023007
18022014
18061005
18061004
18061003
50403002
18022026
18022010
18061014
50301102
50102031
18061046
18061043
18061021
18061042
18061033
18061034
50101044
18061035
50103063
50201013
50301090
50102023
18061007
18061006
23041030
18061015
18061010
50201019
50103007
18061012
50101039
18061011
50302008
18061013
18061026
50111017
18061040
18061041
DESCRIPTION.
Round head screw
Fence guard
LH hand fence
Washer
Lock handle
Pivot stud
RH hand fence
Fence nut
Knife screw
Blade-left
Blade-right
Mitring head
E-Ring
Pivot bar
Top pivot block
Connecting rod
Washer
Cap screw
Vertical guide
Back column
Scale
Main table
LH scale for mitring angle
RH scale for mitring angle
Hex screw
Screw
Set Screw
Hex nut
Washer
Cap screw
LH Bottom guide
RH Bottom guide
Handle grip
Handle
Handle bracket
Hex nut
Set screw
Shoulder shaft
Hex nut
Clamping block base
Spring washer
Pin
Spring
M5*0.8P*12L
SIZE
8.2*23*2t
M8*1.25P*40L
ETW-8
8.2*16*1t
M8*1.25P*25L
M12*1.75P*80L
M6*1.0P*50L
M6*1.0P
13.5*28*3t
M6*1.0P*10L
M8*1.25P
M8*1.25P*16L
M8*1.25P*55L
M8
M6*1.0P*55L
Knob
Sliding block
Length scale
19
Q'T
Y
6
2
1
4
2
1
1
2
6
1
1
1
6
1
1
1
6
5
1
1
2
1
1
1
2
1
4
5
2
6
1
1
1
1
1
2
1
1
1
1
3
1
1
1
1
1
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
18011013
18061039
18061022
18061031
50107004
18061027
50301111
50101043
33052024
18061030
18061024
50101064
18061025
18061019
18061018
18061032
50301057
50101076
18061008
18061009
50251035
50107020
50301087
50107017
50201021
50302006
50155014
50155037
18011012
18061049
18011015
18011016
18061047
50252023
18061048
18061036
18061037
18061038
50404008
50122002
Lock plate
Stop/vernier rule
Length scale
long extruding rule
Hex screw
Measuring table
Washer
Hex screw
Bracket
Left extension table
Base
Hex screw
Waste box
Wheel
Magnet
Pad
Washer
Hex screw
LH Fence
RH Fence
Hex net
Screw
Washer
Round head screw
Hex nut
Sping washer
Phillips flat head screw
Phillips flat head screw
Lock plate
Positioning pole
Spring
Base
Spring (Right)
Nylon nut
Spring (Left)
Fixed block
Fixed screw
Fixed piece
O-ring
Positioning screw
M6*1.0P*12L
10.2*23*2t
M10*1.5P*25L
M8*1.25P*16L
5.1*12*1t
M6*1.0P*55L
5/16"-18UNC
M8*1.25*12L
6*12*1t
M5*0.8P*12L
M5*0.8P
M5
1/4"-20UNC*7/8"L
1/4"-20UNC*1 1/4"L
1/4"-20UNC
2*1
M8*1.25P*15L
20
1
1
1
1
7
1
4
4
1
1
1
4
1
4
1
1
2
1
1
1
2
1
7
1
1
1
2
2
2
2
2
2
1
2
1
1
1
2
2
2
1806-B2
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PARTS
NO.
18021005
50102047
18062002
18021001
18021002
18021003
18021007
51201003
18021006
18021004
18062001
50113002
18062004
18062003
50301073
50107004
50301123
50102023
18025009
18025010
DESCRIPTION.
LH Holder
Cap screw
LH Bottom slide
Nut
Nut
Shaft screw
LH rebate support
Rivet
RH reabte support
RH Holder
RH Bottom slide
Screw
Support shaft
Fixed plate
Flat washer
Round head screw
Flat washer
Cap screw
Pole
Bush
SIZE
M6*1.0P*40L
M10*1.5P
M10*1.5P
M10*1.5P
1/8"*1/2"L
M6*1.0P*20L
6.5*13*1t
M6*1.0P*12L
6.4*16*1.6t
M6*1.0P*10L
21
Q'TY
1
2
1
2
2
2
1
4
1
1
1
2
2
2
4
4
2
2
2
2
22
23
1807-B1 w/casting fence
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
PARTS
NO.
50107004
50301087
18061008
18061009
18022014
18061005
18061003
50301061
50102031
50403002
18022026
18022010
18061004
18061046
18061042
18061021
18061043
18061033
50301090
50101044
50103063
50201013
18061034
50102023
18061007
18061006
50104059
18023008
18061045
50301102
50114007
18023004
18061044
18023007
18011013
50111020
18061040
50111017
18023013
18061031
18061041
18061039
18061022
18061027
50301111
DESCRIPTION.
Round head screw
Flat washer
Blade guard - left
Blade guard - right
Knife screw
Blade -left
Mitring head
Flat washer
Cap screw
E-ring
Pivot bar
Top pivot block
Blade - right
Vertical guide
Main table
Scale
Back column
LH scale for mitring angle
Flat washer
Hex screw
Scale
Hex nut
RH scale for mitring angle
Cap screw
LH bottom guide
RH bottom guide
Round head screw
Fence guard
LH hand fence
Flat washer
Lock handle
Pivot stud
RH hand fence
Fence nut
Lock plate
Knob
Sliding block
Knob
Spring
Long extruding rule
Length scale
Stop/vernier rule
Length scale
Measuring table
Flat washer
M6*1.0P*12L
6*12*1t
SIZE
8.2*23*2t
M8*1.25P*25L
ETW-8
13.5*28*3t
M12*1.75P*80L
M6*1.0P*50L
M6*1.0P
M6*1.0P*10L
M5*0.8P*12L
8.2*16*1t
M8*1.25P*40L
M8*1.25P*18L
M6*1.0P*55L
10.2*23*2t
24
Q'T
Y
7
7
1
1
6
1
1
4
2
2
1
1
1
1
1
2
1
1
2
2
4
5
1
6
1
1
5
2
1
12
2
1
1
2
1
1
1
1
1
1
1
1
1
1
4
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
50101043
18061030
50101064
18024010
18071001
50169004
18024012
18024013
18024011
33015022
18024009
18053003
50301057
50104014
18053002
18053004
50102010
18024015
18071004
50201022
50301088
18054001
18024008
18024007
18024002
50202012
18024001
18024003
50103004
18024014
18024004
25011017
18024005
34011029
18071002
18071003
50101076
50107017
50302006
50155014
50155037
18011012
18061049
18011015
18011016
18061047
50252023
18061048
Hex screw
Left extension table
Hex screw
Washer
Stand
Screw
Flat washer
Screw
Rear stop
Rubber stop
Upper spring holder
Side waste chute
Flat washer
Round head screw
Waste chute
Support bar
Cap screw
Grip
Connecting rod
Hex nut
Flat washer
Yoke
Spring
Lower spring holder
Pivot bar
Nylon nut
Footpedal bracket
Collar
Set screw
Foot pad
Footpedal
Spacer
Pivot screw
Protection
Tools holder
Cutlery holder
Hex screw
Round head screw
Spring washer
Phillips flat head screw
Phillips flat head screw
Lock plate
Positioning pole
Spring
Base
Spring (Right)
Nylon nut
Spring (Left)
M10*1.5P*25L
M8*1.25P*16L
1/4"-20UNC*5/8"L
5.1*12*1t
M5*0.8P*10L
M8*1.25P*16L
M12*1.75P
13*25*2t
M10*1.5P
M6*1.0P*8L
M6*1.0P*55L
M5*0.8P*12L
M5
1/4"-20UNC*7/8"L
1/4"-20UNC*1 1/4"L
1/4"-20UNC
25
4
1
8
4
1
2
1
1
1
1
2
2
4
4
1
1
4
4
1
2
2
1
2
2
1
2
1
2
2
1
1
2
2
2
1
1
1
1
1
2
2
2
2
2
2
1
2
1
26
27
Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the
environment, take the packaging to the local recycling centre and place into the appropriate recycling bin.
Only for EU countries
Do not dispose of electric tools together with household waste material. In observance of European Directive
2002/96/EC on waste electrical and electronic equipment and its implementation in accordance with national law,
electric tools that have reached the end of their life must be collected separately and returned to an environmentally
compatible recycling facility.
Axminster Tools & Machinery Ltd
Weycroft Avenue, Axminster, Devon EX13 5PH
axminster.co.uk