Auto-Charging Dehydrating Breathers

C O M P O N E N TS
2ND GENERATION
Auto-Charging Dehydrating Breathers
INTELLIGENT TECHNOLOGY HELPS KEEP OIL DRY AND TRANSFORMERS FREE FROM CONTAMINANTS
Second generation ARDBs use breather
intelligence technology and a bypass valve to
automatically schedule regeneration and isolate
the transformer from the silica gel. Modular
design and high temperature, UV-resistant,
anti-corrosive plastic housing allow for use in
confined areas.
SEE BACK SIDE FOR PART NUMBER
CONFIGURATION TOOL.
AUTOMATIC RECHARGE USING INTELLIGENT
REGENERATION CONTROL TECHNOLOGY
Keeping the silica gel dry eliminates the need for periodic replacement
of the desiccant. Logic controls include a humidity switch, timer and
vacuum protection circuit that automatically “learn” to regenerate during
transformer exhale only, driving moisture out of the desiccant while
keeping the transformer isolated from steam-generated contaminants.
USER-CONTROLLED TIME-BASED SET TINGS
Included timer allows variable time-based settings for user-controlled
regeneration of silica gel. Time settings for 5, 10, 20 or 40 day intervals
can be set by the customer. Intelligent humidity sensor serves as a
back-up to ensure user-based settings are adequate for proper
breather operation.
AIR FLOW
INTEGRATED AL ARMS
LED indicators on front cover of control box visually alert user of breather
operational status. Relay contacts are also included for remote (SCADA)
breather monitoring.
QUICK AND EASY INSTALL ATION
TOP CAP
VACUUM SENSOR
ISOLATION VALVE
HUMIDITY SENSOR
TOP MOLDING
PC BOARD
Lightweight unit with integrated controls
installs easily on as little as a 7″x5″ flat
mounting surface. Quick-connect power
and alarm harnesses included.
OPERATION
( D I A G R A M AT L E F T )
During regeneration, a heating element located inside the ARDB2
assembly heats the partially saturated silica gel, driving moisture out.
This moisture condenses on the polycarbonate tube, forming free water,
which then flows down the tube and out the bottom vent.
~
AIR FLOW
HEATING
ELEMENT
Available in SMALL/8,000 gallon size and LARGE/18,000 gallon size.
For increased capacity, multiple ARDB2s may be applied to the same tank.
See back side of this brochure for LED indicator colors.
POWER/SIGNAL PLUGS
POLYCARBONATE
TUBE
SCREEN & FILTER
HEAT DISTRIBUTION
FINS
BOTTOM MOLDING
SILICA GEL
All ARDB2s ship with an environmentally-friendly and enhanced
performance clear silica gel.
OPTIONAL HEATED
FILTER VENT
WATER FLOW
DURING REGEN.
WATER FLOW
DURING REGEN.
TRANSFORMERS | SERVICE | TRAINING | COMPONENTS
Build Your Own Part Number Using Configuration Below
ARDB 2 - XXXX
CA
PA
PO
CI
TY
W
ER
&
CA
BL
IN
G
SYSTEM TYPE
2nd GENERATION AUTO
RECHARGING DEHYDRATING
BREATHER
6.85
174mm
SMALL BREATHER
For increased capacity,
multiple ARDB2s can be
applied to the same tank.
SE
RV
I
CE
MOU
NTIN
G&
DU
TY
2.2 lbs / 1kg DESICCANT
CAPACITY 8,000 Gal.
0
0
100V-240V
(STD. 10M POWER &
SENSE CABLES)
LARGE BREATHER
4.4 lbs / 2kg DESICCANT
CAPACITY 18,000 Gal.
1
1
100V-240V
(FLEX CONDUIT
ADAPTER BOX)
CON
NEC
TION
PA R T N U M B E R F O R
S M A L L B R E AT H E R
WITH CONDUIT BOX:
ARDB2-0100
OPT
0
STANDARD SERVICE,
FOR SERVICE
0°C TO 80°C
1
ARCTIC BREATHER
FOR SERVICE
-50°C TO 80°C
ION
S
6.85
174mm
0
STANDARD PANEL
OR PIPE MOUNT,
HOSES, FITTINGS
& DESICCANT
INCLUDED
3
DIN 42562-5 TYPE
MOUNTING FLANGE
W/ GASKET, (1030-1628)
HOSE, FITTINGS &
DESICCANT
6.85
174mm
6.73
L ARGE ARDB2
ARCTIC BREATHER
Oil Volume: 18,000 gallons or less
Amperage: 5.5 amps start-up / 2 amps during operation
• Fully functional between –50°C and 80°C
6.13
156mm
8.84
225mm
6.13V I E W
TO P
156mm
SAME FOR BOTH LARGE
AND SMALL ARDB2 UNITS
8.84
6.13
•From 0°C to –50°C,
the heated filter 225mm
vent
prevents
156mm
freezing of water generated from the regeneration
11.38
process, allowing complete drainage
289mm
17.35
441mm
•See models ARDB2-0010 and ARDB2-1010 on the configurator above
4.88
124mm
10.95
278mm
FEATURES — ALL ARDB2 MODELS:
• Corrosion/UV-resistant high temperature plastic housing
• Integrated programmable timer inside housing
• Humidity sensor/switch
6.85allows exhale only during regeneration
• Two position valve
174mm
ALL FULL KITS
INCLUDE THE FOLLOWING:
• Two 1/2 NPT hose barbs (for breather and end use location)
• 16.5 ft of breather hose
• Silica gel/Desiccant: 2.2 lbs/1 kg with small breather, 4.4 lbs/2 kg with large breather
• 32.8 ft /10 m power and signal/alarm connection cables
• 1/4″ mounting hardware NOT supplied with kit
17.35
441mm
11.38
289mm
POWER REQUIREMENTS: 100–240 VAC, 50/60 Hz
6.85
174mm
FRONT VIEW
MOUNTING: Panel mounting standard (options available)
6.73
SIDE VIEW
SMALL ARDB2
Oil Volume: 8,000 gallons or less
Amperage: 5.5 amps start-up / 1 amp during operation
8.84
225mm
6.13
156mm
LED INDICATORS:
• Solid Green — Normal Operation
• Solid Amber — Regeneration Mode
• Blinking Amber — Humidity Sensor Failure
• Blinking Red — Vacuum Sensor Failure
6.13
• Solid Red — Heater Failure
156mm
REMOTE MONITORING:
• Power Failure Solenoid • Valve Relay Failure
• Heater Relay Failure • Vacuum Switch Failure
REGENERATION:
• Primary — User adjustable time-based
• Secondary — Humidity sensor with Logic controls
NOTE: Vacuum sensor overrides all regeneration controls.
11.38
289mm
10.95
278mm
4.88
124mm
8.84
225mm
17.35
441mm
CALL 800-338-5526
VISIT www.waukeshacomponents.com
SPX TRANSFORMER SOLUTIONS
9011 Governors Row | Dallas, Texas 75247
To continually improve its products and services, SPX Transformer Solutions, Inc. reserves the right to
change specifications and features without notice. Please contact us for certified dimensions and drawings.
FRONT VIEW
SIDE VIEW
U.S. Patent Nos. 5,902,381; 6,797,037; 7,285,150 and 7,332,015.
© 2016 SPX Transformer Solutions, Inc.
ARDB2-0812 (Rev. 12/15)
8.8
225m