Product Catalog - Nordic Fiberglass, Inc.

Transcription

Nordic Fiberglass, Inc.
Product Catalog
Single & Three Phase
Transformer
Box Pads
Single & Three Phase
Sectionalizing
Cabinets
Hand Holes,
Secondary & Meter
Pedestals, & More...
ORDIC FIBERGLASS, INC.
Quality Products for the Electric Utility Industry
P.O. Box 27 Warren, MN 56762 Tel: 218-745-5095 Fax: 218-745-4990 www.nordicfiberglass.com
This Page is intended to be blank
Table of Contents
Contents
Table of Contents
Warranty Box Pads, 1 Phase Transformer
Box Pads, 3 Phase Transformer
Box Pads, Air-Insulated Switchgear, Oil-Filled Switchgear
Box Pads, Air-Insulated Switchgear with an Access Panel
Box Pads, Transformer-Meter-Switch Cabinets, 1 Phase Sectionalizing
Cabinets, 2 Phase Sectionalizing
Cabinet Extensions
Cabinets, Deferral
Cabinets, Sub-Surface Sectionalizing
Cabinets, Vacuum Switch
§Covers, Ground Sleeve
Extenders and Adapters
Flexi-Flags, Curb, and Cabinet Markers
Ground Sleeves, 1 & 3 Phase Sectionalizing
Ground Sleeves, Traffic
Hardware & Miscellaneous Accessories
Hill Holders
Pedestals, Hand Holes
Pedestals, Looping
Pedestals, Secondary
Pedestals, Meter
Pedestals, Tap
07/15
Fabricators of Quality Fiberglass Products for the Electric Utility Industry
21415 US Highway 75 NW · P.O. Box 27 · Warren · Minnesota · 56762
Ph: (218) 745-5095 · Fx: (218) 745-4990 · www.nordicfiberglass.com
3
4
5
6
7
8
9
12
17
19
26
27
28
29
30
31
32
33
34
35
38
39
41
42
46
49
52
Page 3
Warranty
WARRANTY
THE FOLLOWING WARRANTY APPLIES TO ALL
FIBERGLASS PRODUCTS
SHIPPED AFTER MARCH 1, 1999
Nordic Fiberglass, Inc. warrants all of its products to
be free of defects in materials and workmanship for a
period of three years from date of purchase when used
under normal conditions and for the purpose for which it
was designed.
In addition, Nordic Fiberglass, Inc. warrants its
FIBERGLASS products for a period of thirty years
against failure due to loss of strength through degradation when used under normal environmental conditions.
Acts of God are excluded.
Purchaser’s sole remedy for any defect shall be
the repair or replacement of the product. Whether the
defect is remedied by repair or replacement shall be the
decision of Nordic Fiberglass, Inc. and shall constitute
the complete fulfillment of Nordic Fiberglass’ obligation
under this warranty. All expenses related to removal
and transportation incurred by the owner of the product
in delivering the product to Nordic Fiberglass, Inc. for
repair or reinstallation of the repaired or replaced product shall be the responsibility of the product owner.
This warranty is expressly in lieu of any other express or implied warranties and Nordic Fiberglass, Inc.
makes no other express or implied warranty, including
any implied warranty of fitness or merchant ability. In
no case shall Nordic Fiberglass, Inc. be liable for consequential, special or indirect damages resulting from
breach of this warranty.
Page 4
07/15
Box Pads for Single Phase Transformers
CBP-37-43-15A-MG-22x24
GS-37-43-32A-CE-2-MG-26x32
TP-42-42-5-MG-12x20
Installed CBP unit
CBP with Transformer
Features:
• CBP units (compression box pad) are manufactured of SMC (Sheet Molding Compound).
• SMC is a thermosetting compound which is pre-mixed with pigments that are molded into the fiberglass and cannot
peel. Fire retardant and UV additives are permanently molded in throughout the laminate.
• GS units are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using 18 oz.
woven roving glass reinforcement for great strength. Munsell green surface coat is applied for superior weather-ability.
• Accommodates typical single phase transformers ranging from 25kVA up to 167 kVA ratings.
• Optional tie-down brackets are available to hold the transformer in place.
• Bottom flange provides a stable footing for installation.
Benefits:
• Molded in ribs resist sidewall ground pressures to help prevent sidewall deflection.
• No costly forms to set up, no cement needs to be poured, the fiberglass box pads reduce installation time by being built
ready to go.
Box Pads for Single Phase Transformers
07/15
CBP-37-43-15A-MG-22x24
GS-34-34-15B-MG-20x20
GS-42-42-18-MG-25x25
CBP-37-43-15B-MG-20x20
GS-36-26-24-MG-24x12
GS-42-42-32-MG-25x25
CBP-37-43-15C-MG-21x12
GS-36-36-15-MG-22x22
GS-42-48-16-MG-26x12
CBP-37-43-15F-MG-25.5x30
GS-36-36-18-MG-24x24
GS-42-48-18-MG-25x25
CBP-37-43-24A-MG-22x24
GS-36-36-24-MG-25x25
GS-42-48-24-MG-26x12
CBP-37-43-24B-MG-20x20
GS-36-36-32-MG-25x25
GS-42-48-32C-MG-22x24
CBP-37-43-24C-MG-21x12
GS-37-43-32A-CE-2-MG-26x32
GS-42-48-32-MG-26x12
CBP-37-43-24F-MG-26x30
GS-37-43-32B-CE-2-MG-20x20
TP-42-42-5B-MG-28x13
GS-24-37-25-MG-16x24
GS-37-43-32C-CE-2-MG-22x24
TP-42-42-5-MG-12x20
GS-25-40-18-MG-15.5x11.5
GS-37-43-42A-MG-25x31
TP-48-48-5-MG-25x13
GS-25-40-24-MG-14x10
GS-37-43-48-MG-25x31
GS-28-28-15-MG-20x20
GS-37-46-15A-MG-22x24
GS-34-30-25-MG-22x18
GS-37-48-32A-CE-2-MG-26x31
GS-34-34-15A-MG-22x24
GS-37-52-15-MG-23x24
Page 5
Box Pads for Three Phase Transformers
GS-69-47-36RT-MG-56x16
GS-69-47-18RT-MG-56x16
TP-66-72-5-MG-18x42
3 Phase Box Pad Installation
3 Phase Box Pad Installation
Features:
• RT series box pads for three-phase transformers are available in various heights.
• Designed for strength without excessive weight.
• They are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using 18 ounce
woven roving glass reinforcement.
• Multiple layers of chopped and woven roving glass encapsulate plywood and 2x6’s, providing a rigid surface for the
transformer oil tank.
• On the 36” box pads, the 2x4 is encapsulated around the box pad perimeter halfway up the sidewall and vertical ribs are
molded into the bottom half on all four sides.
• The height of the box pads allows for excellent cable training and cable mobility for most three-phase transformers.
• The box pads are spacious enough to accommodate looping of extra cable.
Benefits:
ready to go.
• In case of elbow failure, the extra looped cable enables the lineperson to use the extra slack for installing a new elbow.
Box Pads for Three Phase Transformers
GS-111-44-36RT-3O-MG-20x11
GS-67-59-18RT-MG-52x18
GS-72-62-17RT-MG-58X18
GS-75-69-36RT-MG-58x18
GS-111-44-36RT-MG-93x11
GS-67-59-36RT-MG-52x18
GS-72-62-30RT-MG-58X18
GS-80-54-18RT-MG-60x18
GS-47-47-20RT-MG-40x13
GS-67-69-18RT-MG-58x24
GS-72-62-36RT-MG-58X18
GS-80-54-36RT-MG-60x18
GS-54-44-32RT-MG-41x15
GS-67-69-30RT-MG-58x24
GS-72-72-20RT-MG-60x25
GS-84-66-20RT-MG-64x18
GS-54-52-15RT-MG-41x15
GS-69-47-18RT-MG-56x16
GS-72-72-36RT-MG-60x25
GS-84-66-36RT-MG-64x18
GS-60-47-36RT-MG-48x15
GS-69-47-36RT-MG-56x16
GS-75-47-20RT-MG-58x16
GS-86-78-18RT-2X-MG-74x22
GS-65-44-20RT-MG-56x15
GS-69-65-18RT-MG-56x16
GS-75-47-36RT-MG-58x16
GS-86-78-36RT-2X-MG-74x22
GS-65-44-36RT-MG-56x15
GS-69-65-36RT-MG-56x16
GS-75-69-18RT-9K-MG-48x16*
TP-48-64-5-MG-12x30
GS-65-56-18RT-MG-56x16
GS-72-56-17RT-MG-58x18
GS-75-69-18RT-MG-58x18
TP-48-72-5-MG-18x42
GS-65-56-36RT-MG-56x16
GS-72-56-30RT-MG-58x18
GS-75-69-36RT-9K-MG-48x16*
TP-66-72-5-MG-18x42
TP-72-72-10-MG-60x18
*Check out our new 9K box pads, Under 9,000lbs., and it fits...that’s it!
Please be sure to send Nordic Fiberglass a footprint and weight of the transformer
in order to determine the appropriate top opening and box pad reinforcement.
Page 6
07/15
Box Pads, Air-Insulated Switchgear, Oil-Filled Switchgear
Box Pads for Air-Insulated & Oil-Filled Switchgear
GS-75-73-36-MG-67x62
GS-75-73-36-MG-67x62
GS-75-73-36RT-2O-MG
Installed box pad
Actual installation
Features:
• Nordic box pads for switchgear are available in various sizes.
• They are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using 18 ounce
woven roving glass reinforcement. Munsell green surface coat is applied for superior weatherability and protection from
ultraviolet light.
• These box pads are designed with steps built into the sidewalls for greater vertical strength and resistance to deflection in a buried position. The steps are reinforced with 2x4’s, which are completely encapsulated in additional layers of
chopped glass and woven roving glass. Vertical ribs are molded in below the steps for added strength.
• The RT-2O series of box pads have extra reinforcements to accommodate oil-filled switchgear. These box pads are
designed with two top openings to meet the openings of the switch base. A footprint of the switch is required to ensure
proper placement of the openings.
• Bottom flange provides a stable footing for installation.
Benefits:
• Molded in ribs resist sidewall ground pressures to help prevent sidewall deflection.
ready to go.
Box Pads for Air-Insulated & Oil-Filled Switchgear
GS-106-74-48-MG-96.5x62
GS-65-44-36-MG-54.5x36
GS-75-73-36RT-2O-MG
GS-106-74-36R-MG-96x14
GS-65-56-36-MG-50x40
GS-77-69-18-MG-66x58
GS-124-74-36-MG-114.5x62
GS-67-61-36-MG-59x51
GS-77-69-36-MG-66x58
GS-124-74-36R-MG-106x16
GS-67-61-48-MG-59x51
GS-80-36-36-MG-72x30
GS-125-61-48R-MG-24x47-77.5x20-GSC
GS-69-47-36-MG-61x39
GS-80-54-18A-MG-71.5x45.5
GS-150-61-48R-MG-24x47-95x20-GSC
GS-69-47-36R-MG-14x30
GS-80-54-36A-MG-71.5x45.5
GS-50-30-20-MG-28x22
GS-69-65-18-MG-58x51
GS-80-54-36B-MG-62x34
GS-50-40-32-MG-41x31
GS-69-65-36-MG-58x51
GS-84-66-36-MG-65x51
GS-50-50-54-MG-42x42
GS-72-40-36-MG-52x28
GS-84-66-36R-MG-64x12
GS-54-32-26-MG-46x24
GS-75-45-18-MG-61x31.5
GS-86-78-18-MG-70.5x63
GS-54-44-15-MG-42x32
GS-75-45-36-MG-61x31.5
GS-86-78-36-MG-70.5x63
GS-54-44-32-MG-42.5x31
GS-75-47-36RT-2O-MG
GS-55-37-36-MG-43x25
GS-75-48-36-MG-61x31.5
GS-56-56-20-MG-44x44
GS-75-69-36-MG-65x59
GS-57-44-32-MG-47x34
GS-75-73-20-MG-67x62
GS-64-37-36-MG-56x29.5
GS-75-73-36-MG-67x62
07/15
GS-86-78-36RT-2O-MG
GS-86-84-36 2 PIECE-MG-73x76
GS-89-84-36 2 PIECE-MG-73x76
GS-96-54-36-MG-86x44
GS-96-67-48-MG-59x51-59x24-GSC
Page 7
Box Pads, Air-Insulated Switchgear with an Access Panel
Box Pads for Air-Insulated
Switchgear with an Access Panel
Features:
• Designed to accommodate various models of airfilled switchgear.
• GS-96-67-48-MG-59x51-59x24-GSC is designed to
accommodate S&C PMH-6 thru PMH-19 air-filled
switchgear in the 15kV base size.
• GS-125-61-48R-MG-24x47-77.5x20-GSC and
GS-150-61-48R-MG-24x47-95x20-GSC box pads
are designed to accommodate large G&W air-filled
switchgear.
• Nordic Fiberglass requires a footprint of your airfilled switchgear to determine the correct box pad
for your application.
GS-96-67-48-MG-59x51-59x24-GSC
• Access panel allows entry into the box pad in order
to feed underground cables to the switch.
• Cover is secured with four penta-head bolts, two
of these are inside a metal security case for added
protection and padlocking.
• Cover includes the lettering, “WARNING!
ELECTRIC HAZARD ENTRY PROHIBITED”
• Cover has down-turned lips around three sides of
the cover’s perimeter for extra security.
GS-125-61-48R-MG-24x47-77.5x20-GSC
Benefits:
• Access panel allows a lineperson to enter the box pad and
pull cable up to the terminals.
• In case of an electrical fault or
blown elbow, the extra room
inside the interior of the box
pad allows the lineperson to
enter and repair the fault or
damaged elbow.
GS-150-61-48R-MG-24x47-95x20-GSC
Page 8
07/15
Box Pads, Transformer-Meter-Switch
Transformer/Meter/Switch Box Pad
Meter Pedestal/Box Pad Features:
GS-37-39-15-MP-MG-22x22 & GS-37-39-24-MP-MG-22x22
• Box pads available in 15” and 24” heights accommodate single phase
transformers ranging from 25kVA up to 167kVA.
• Provides a raceway between the transformer and the meter.
• In case of an elbow failure, the extra cable slack in the box pad’s cavity allows
the line-person to quickly attach a new elbow and restore service.
• Install up to 2 meter enclosures on the outside walls of the MPP meter pedestal.
• Up to three secondary connectors can be installed on the inside walls of the
MPP unit.
GS-37-39-15-MP-MG-22x22
• Large expansive door on the MPP meter pedestal allows easy access inside
the pedestal.
• Penta-head bolt and provisions for pad locking on the MPP give it a double
security feature.
• Meter pedestal and box pad are shipped separately, assembly is required.
GS-37-39-24-MP-MG-22x22
GS-37-39-15-MP-MG-22x22 installed
07/15
Page 9
Secondary Pedestal/Box Pad Features:
• 15” high box pad accommodates single phase transformers ranging from 25kVA up to 167kVA.
• Includes a pedestal lid.
• Provides a raceway between the transformer and the secondary pedestal.
• Accommodates free standing connectors.
• Accommodates Nordic’s optional connector bracket with optional 350 or 600MCM connectors.
• Connector bracket sold and shipped separately, assembly is required.
GS-37-39-15-SP-MG-22x22
• Fiberglass extension for the pedestal lid is centered behind the box pad.
(shown with optional connector bracket & connectors)
(transformer not included)
GS-37-43-15-SPR-MG-22x22
• The box pad and secondary cable opening are parallel to each other for comfortable cable accessibility.
• Training low voltage cable underneath the transformer to the extension’s secondary cable compartment makes
connecting cables easier in-line.
(GS-37-43-15-MG-22x24-SPR shown
without cover)
Page 10
(transformer not included)
07/15
GS-37-52-15-TMS-MG
GS-72-40-18-TMS-MG
GS-37-52-15-TMS-MG with
single phase transformer & meter
GS-80-36-36-2O-MG-TS
GS-80-36-36-2O-MG-TS with
secondary tap pedestal bolted
to adapter and a single phase
transformer.
Features:
GS-37-52-15-TMS-MG & GS-72-40-18-TMS-MG
• One complete unit designed for a single phase transformer and one meter/switch.
• Box pad allows for extra looping of primary and secondary cables.
• In case of an elbow failure, the extra cable slack allows the lineperson to quickly attach a new elbow and restore
service.
• Provides a raceway between the transformer and meter.
Alternative Energy Uses:
• Facilities using supplemental energy system (wind energy) can switch and meter their power with their own energy
provider.
• Allows for Net Metering of an energy generator (wind turbine).
• Cost effective for alternative energy generating utility customers and businesses.
• Nordic Box Pads provide the platform for harvesting alternative energy sources.
Features:
GS-80-36-36-2O-MG-TS
• Two 22” x 24” top openings accommodates two pieces of electrical equipment at the same time.
• Provides a raceway between the transformer and enclosure.
• 80” long x 36” wide top surface area enables a wide variety of equipment to be installed on this TMS box pad.
• Install Nordic single phase cabinets, single phase transformers, or other various pieces of equipment below:
• Single phase transformer and GSC-36-36-MG cover.
• Single phase sectionalizing cabinet and single phase transformer.
• Single phase transformer and GSA-36-36-MG-25x10 adapter plate.
• Secondary tap pedestal bolted to GSA-36-36-MG-25x10 adapter plate and sing phase transformer.
07/15
Page 11
15/25kV 200Amp Single Phase Sectionalizing Cabinets
Features:
• Rust free fiberglass construction and stainless steel hardware.
• The exterior Munsell green coating which contains UV stabilizer and
provides superior weather-ability and resistance to ultraviolet attack.
• P-107 stainless steel locking system with a silicon bronze pentahead bolt provides double locking.
• Stainless steel self locking cam arm holds lid open.
• Optional copper grounding is available.
• Typically installed as a one piece unit, the customer can unbolt
the cabinet from the ground sleeve thus enabling the ground sleeve to
be installed during construction without subjecting the cabinet to
accidental damage. After construction is over, the cabinet can be
installed on the ground sleeve.
• Meets ANSI C57.12.28 Pad-Mounted Enclosure Integrity
Standard.
ND-22022 Series:
ND-2202248-MG-125-X-X
• Two-piece design: Cabinet is produced of SMC, (Sheet Molding
Compound).
• Ground sleeve is produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using woven
roving glass reinforcement, which adds greatly to their strength.
• Hot-dipped galvanized MP-125 mounting plate accommodates a
2, 3, or 4 pt., 15/25 kV, 200/600Amp junction with U-straps, except
Cooper 35kV.
• Does not accommodate 200A taps off of the 600A junction.
• Below parking allows for stand-offs or feed throughs to be installed.
ND-23222 Series:
• Two-piece design: Cabinet and ground sleeve are produced of fireretardant resin and a combination of chopped glass spray-up and hand
lay-up using woven roving glass reinforcement, which adds greatly to
their strength.
• Hot-dipped galvanized MP-112 mounting plate accommodates a 2, 3,
or 4 pt., 15/25 kV, 200/600Amp junction with U-straps, except Cooper
35kV.
ND-2322248-MG-112-X-X
• In-line parking allows for stand-offs or feed throughs to be installed.
15/25kV 200Amp Single Phase
Sectionalizing Cabinets
Parking
Top
Width
Top
Depth
Cabinet
Height
Hot Stick
Operating
Depth
ND-2202248-MG-125-X-X
Below
21”
21”
48”
22
ND-2322248-MG-112-X-X
In-Line
32.5”
32.5”
48”
20.5”
Page 12
Recommended Burial Depth
Finish grade approximately 6” below locking system.
07/15
15/25/35kV 600Amp Single Phase Sectionalizing Cabinet
Features: ND-322864-MG-PA38-X-X
• Nordic cabinets are produced of fire-retardant resin and a combination
of chopped glass spray-up and hand lay-up using woven roving glass
reinforcement, which adds greatly to their strength.
• The exterior is applied with a Munsell green gel-coat, which contains
UV stabilizer and provides superior weather-ability and resistance to
ultraviolet attack.
• P-107 stainless steel locking system with a silicon bronze penta-head
bolt provides double locking.
• Meets ANSI C57.12.28 Pad-Mounted Enclosure Integrity Standard.
• One-piece design, ground sleeve is part of the cabinet.
• Aluminum PA/PB 38 mounting plate accommodates a single
15/25/35kV 200/600Amp junction with U-straps, (accommodates 200A
taps), including Cooper 35kV 200A/600A junctions.
• The sliding rail on the PA38 or PB38 allows for stand-offs or feed
throughs to be installed on the stainless steel parking stands either
above or below.
Benefits:
• Pulling elbows with a hot stick is made easier with the adjustable
12°-20° mounting bracket found on the PA or PB38 mounting plates.
• Rotational lid rotates on pivot bolts creating a lower center of gravity
that reduces the force required to open the cabinet.
• The wide open lid allows cable pulling equipment to be used inside
of the cabinet with no interference.
• Hot-stick operators have open access to elbows with no lid
interference from the top, front, or sides.
• The cabinet’s four eyebolts allow the lineperson to simply hook-up
the cabinet, position it over the cables, and place it in the excavated
area.
ND-322864-MG-PA38-X-X
15/25/35kV 600Amp Single
Phase Sectionalizing Cabinet
ND-322864-MG-PA38-X-X
07/15
Parking
Above
Top
Width
38”
Top
Depth
29.5”
Cabinet
Height
64”
Hot Stick
Operating
Depth
25.5”
Recommended
Burial Depth
Finish grade
approximately
6” below
locking system.
Page 13
15/25kV 200Amp GS Mount Single Phase Sectionalizing Cabinets
Features:
ND-301830-MG-102A-X-X &
ND-301830H-MG-102A-X-X Series
• Rust free fiberglass construction and stainless steel
hardware.
• Nordic cabinets are produced of fire-retardant resin and a
combination of chopped glass spray-up and hand layup using woven roving glass reinforcement, which adds
greatly to their strength.
• The exterior is applied with a Munsell green gel-coat,
which contains UV stabilizer and provides superior weather-ability
and resistance to ultraviolet attack.
• P-107 stainless steel locking system with a silicon bronze pentahead bolt provides double locking.
ND-301830-MG-102A-X-X
Standard.
• Two-piece design: ND-301830-MG-102A-X-X &
ND-301830H-MG-102A-X-X require a ground sleeve.
• Cabinet and ground sleeve are shipped separately and
require assembly upon receipt (hardware included).
• Optional Ground Sleeves:
• CGS-30-18-18-MG-21x10
• GS-30-18-24-MG-20x9
• GS-30-18-30-MG-21x10
• Hot-dipped galvanized MP-102A mounting plate (also available in stainless steel) accommodates a 2, 3, or 4 pt., 15/25 kV,
200/600Amp junction with U-straps, except Cooper 35kV. In-line
parking allows for stand-offs or feed throughs to be installed.
• ND-301830-MG-102A-X-X includes a lid, this lid is attached to the
top flange of the cabinet with an interlocking stainless steel channel.
• ND-301830H-MG-102A-X-X has a (H) hinged lid, includes a self
locking stainless steel cam arm which holds the lid open.
15/25kV 200Amp Pad or
GS Mount Cabinets
Parking
Top
Width
Top
Depth
Cabinet
Height
Hot Stick
Operating
Depth
ND-301830-MG-102A-X-X
In-Line
30”
19.5”
31”
19”
ND-301830H-MG-102A-X-X
In-Line
30”
19.5”
31”
19”
Page 14
ND-301830H-MG-102A-X-X
H-Hinged
Recommended
Burial Depth
GS Required
07/15
15/25kV 200Amp Pad Mount & Direct Bury Sectionalizing Cabinets
Features:
combination of chopped glass spray-up and hand lay-up
using woven roving glass reinforcement, which adds greatly to
their strength.
• The exterior is applied with a Munsell green gel-coat, which
contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet
attack.
• Hot-dipped galvanized MP-101 mounting plate (also available in stainless steel)
accommodates a 2, 3, or 4 pt., 15/25 kV, 200/600Amp junction with U-straps, except
Cooper 35k. Below parking allows for stand-offs or feed throughs to be installed.
ND-120-MG-101-X-X
• P-107 stainless steel locking system with a silicon bronze
penta-head bolt provides double locking.
• Stainless steel continuous hinge connects the lid to the
cabinet.
ND-120-MG-101-X-X:
• ND-120-MG-101-X-X is used for pad-mount installations.
ND-130-MG-101-X-X
• Cabinet anchor brackets (4x) are shipped attached to the
mounting plate for pad mounting.
• Concrete anchoring hardware is not included.
ND-130-MG-101-X-X & ND-150-MG-101-X-X:
• ND-130 and ND-150 cabinets are used for direct bury
installations.
• The cabinet’s four eyebolts allow the lineperson to simply
hook-up the cabinet, position it over the cables, and place it
in the excavated area.
15/25kV 200Amp Pad &
Single Sectionalizing Cabinets
(Direct Bury)
Parking
Top
Width
Top
Depth
Cabinet
Height
Hot Stick
Operating
Depth
Recommended
Burial Depth
ND-120-MG-101-X-X
Below
23.5”
25.5”
35”
22”
Pad Mount
ND-130-MG-101-X-X
Below
24”
24.5”
37.5”
20.5”
ND-150-MG-101-X-X
Below
23.5”
25.5”
50”
22”
Finish grade
approximately
6” below locking system.
07/15
ND-150-MG-101-X-X
Page 15
15/25kV 200Amp Single Phase Sectionalizing Cabinets
Features:
ND-3624 Series:
• Rust free fiberglass construction.
• One-piece design, ground sleeve is part of the
cabinet.
• Nordic cabinets are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up
using woven roving glass reinforcement, which adds greatly to their
strength.
ND-362436-MG-110-X-X
• The exterior is applied with a Munsell green gel-coat, which contains UV
stabilizer and provides superior
weather-ability and resistance to ultraviolet attack.
• Hot-dipped galvanized MP-110 mounting plate accommodates
a 2, 3, or 4 pt., 15/25 kV, 200/600Amp junction with U-straps,
except Cooper 35kV. In-line parking to allow for stand-offs or
feed throughs to be installed.
ND-362442-MG-110-X-X
• ND-362436-MG-110 X-X can be used for pad-mount or direct
bury installations.
Standard.
Benefits:
• Rotational lid rotates on pivot bolts creating a lower center of
gravity that reduces the force required to open the cabinet.
• The wide open lid allows cable pulling equipment to be used inside of
the cabinet with no interference.
ND-362454-MG-110-X-X
• Hot-stick operators have open access to elbows with no lid interference
from the top, front, or sides.
• The cabinet’s four eyebolts allow the lineperson to simply hook-up the
cabinet, position it over the cables, and place it in the excavated area.
Parking
Top Width
Top Depth
Cabinet Height
Hot Stick
Operating Depth
ND-362436-MG-110-X-X
In-Line
36.5”
23”
36.5”
23”
Pad
ND-362442-MG-110-X-X
In-Line
36.5”
23”
42.5”
23”
ND-362454-MG-110-X-X
In-Line
36.5”
23”
55”
23”
Finish grade
approximately 6” below
locking system.
Page 16
Recommended Burial
Depth
07/15
15/25kV 200Amp Two Phase Sectionalizing Cabinets
Features:
ND-3624 Series:
• One-piece design, the ground sleeve is part of the cabinet.
• Cabinets are produced of fire-retardant resin and a
combination of chopped glass spray-up and hand lay-up using
woven roving glass reinforcement, which adds greatly to their
strength.
contains UV stabilizer and provides superior weather-ability and
resistance to ultraviolet attack.
ND-362436-MG-2101-X-X
• Two hot-dipped galvanized MP-101 mounting plates (also available in stainless steel) accommodate up to two, 2, 3, or 4 pt.,
15/25 kV, 200/600Amp junctions with U-straps, except Cooper
35kV.
• The two MP-101 mounting plates allows for stand-offs or feed
throughs to be installed below the junction.
Standard.
ND-362442-MG-2101-X-X
Benefits:
• Rotational lid rotates on pivot bolts creating a lower center of
gravity that reduces the force required to open the cabinet.
• The wide open lid allows cable pulling equipment to be used
inside of the cabinet with little interference.
• The cabinet’s four eyebolts allow the lineperson to simply hook-up
the cabinet, position it over the cables, and place it in the
excavated area.
ND-362454-MG-2101-X-X
15/25kV 200Amp Two Phase
Parking
Top Width
Top Depth
Cabinet Height
Hot Stick
Operating Depth
Recommended Burial
Depth
ND-362436-MG-2101-X-X
Below
36.5”
23”
36.5”
23”
ND-362442-MG-2101-X-X
Below
36.5”
23”
42.5”
23”
ND-362454-MG-2101-X-X
Below
36.5”
23”
55”
23”
Finish grade
approximately 6” below
locking system.
07/15
Page 17
15/25kV 200Amp Two Phase Sectionalizing Cabinets
Features:
ND-2422850-MG-2125-X-X:
• Two-piece design: Cabinet and ground sleeve are produced of fireretardant resin and a combination of chopped glass spray-up and hand
lay-up using woven roving glass reinforcement, which adds greatly to their
strength.
stabilizer and provides superior weather-ability and resistance to ultraviolet
attack.
• Two hot-dipped galvanized MP-125 mounting plates (also available
in stainless steel) accommodate up to two, 2, 3, or 4 pt., 15/25 kV,
200/600Amp junctions with U-straps, except Cooper 35kV.
• Does not accommodate 200A taps off of the 600A junctions.
• The two MP-125 mounting plates allows for stand-offs or feed throughs to
be installed below the junction.
• P-107 stainless steel locking system with a silicon bronze penta-head bolt
provides double locking.
• Typically installed as a one piece unit, the customer can unbolt the cabinet
from the ground sleeve thus enabling the ground sleeve to be installed
during construction without subjecting the cabinet to accidental damage.
• After construction is over, the cabinet can be installed on the ground
sleeve.
ND-2422850-MG-2125-X-X
Standard.
Benefits:
• The wide open lid allows cable pulling equipment to be used inside of the
cabinet with little interference.
• The cabinet’s four eyebolts allow the lineperson to simply hook-up the
cabinet, position it over the cables, and place it in the excavated area.
15/25kV 200Amp Two Phase
Sectionalizing Cabinet
ND-2422850-MG-2125-X-X
Page 18
Parking
Top Width
Top Depth
Cabinet Height
Hot Stick
Operating Depth
Below
42”
28.5”
50”
25.5”
Recommended Burial Depth
Finish grade approximately 6”
below locking system.
07/15
15kV 200Amp Three Phase Sectionalizing Cabinets
Features:
• Nordic cabinets are produced of fire-retardant resin and a combination of
chopped glass spray-up and hand lay-up using woven roving glass
attack.
• Stainless steel continuous hinge connects the lid to the cabinet.
• One stainless steel self locking cam arm and prop arm hold the lid open.
ND-315-MG-2A5A-X-X:
• One-piece design for the ND-315, ground sleeve is part of the cabinet.
• Hot-dipped galvanized MP-2A5A mounting plate (also available in stainless
steel) accommodates up to three 2, 3 or 4 pt., 15kV 200A loadbreak junctions
with U-straps.
ND-315-MG-2A5A-X-X
• In-line parking allows for parking stand-offs or 2 pt. feedthroughs on either
side of the mounting plate.
ND-2315-MG-2A5A-X-X:
• Two-piece design for the ND-2315. It can also be used for pad-mount
applications without the ground sleeve.
• Hot-dipped galvanized MP-2A5A mounting plate (also available in stainless
steel) accommodates up to three 2, 3 or 4 pt., 15kV 200A loadbreak junctions
with U-straps.
• In-line parking allows for parking stand-offs or 2 pt. feedthroughs on either
side of the mounting plate.
Benefits:
• The cabinet’s eyebolts allow the lineperson to simply hook-up the direct
burial cabinet, position it over the cables, and place it in the excavated area.
Parking
Top
Width
Top
Depth
Cabinet
Height
Hot Stick
Operating
Depth
Recommended
Burial Depth
ND-315-MG-2A5A-X-X
In-Line
70.5”
17.5”
48”
15.5”
ND-2315-MG-2A5A-X-X
In-Line
70.5”
17.5”
53”
15.5”
Finish grade
approximately
6” below locking
system.
15kV 200Amp Three Phase
07/15
ND-2315-MG-2A5A-X-X
Page 19
15/25kV 200Amp Three Phase Sectionalizing Cabinets
Features:
• Nordic cabinets are produced of fire retardant resin and a combination
• The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and
ND-250-MG-101-X-X
• One stainless steel self locking cam arm and prop arm hold the lid open.
ND-250-MG-101-X-X:
• ND-250-MG-101-X-X is used for pad-mount installations.
ND-330-MG-101-X-X
• Cabinet anchor brackets (4x) are shipped attached to the mounting plate
for pad mounting.
ND-330-MG-101-X-X, ND-350-MG-101-X-X,
ND-360-MG-101-X-X:
• Hot-dipped galvanized MP-101 mounting plate (also availabe instainless steel) accommodates up to three 2, 3, or 4 pt., 15/25kV 200A loadbreak junctions with U-straps, except
Cooper 35kV. (ND-330-MG-101-X-X is designed for 15kV 200Amp LBJ’s only)
• Does not accommodate 200A taps off of the 600A junctions. (Includes ND-250)
ND-350-MG-101-X-X
• Below parking on the MP-101 allows for parking stand-offs or 2 pt.
feedthroughs on either side of the mounting plate.
Benefits:
• The cabinet’s eyebolts allow the lineperson to simply hook-up the direct
burial cabinet, position it over the cables, and place it in the excavated
area.
15/25kV 200Amp
Three Phase Sectionalizing
Cabinets
Parking
Top
Width
Top
Depth
Cabinet
Height
Hot Stick
Operating
Depth
Recommended
Burial Depth
ND-330-MG-101-X-X (15kV only)
Below
53.5”
26.5”
36”
19”
ND-350-MG-101-X-X
Below
53.5”
26
48”
23”
ND-360-MG-101-X-X
Below
53.5”
26”
54”
23”
Finish grade
approximately
6” below locking
system.
ND-250-MG-101-X-X
Below
53.5”
26”
34.5”
23”
Pad-Mount
Page 20
ND-360-MG-101-X-X
07/15
15/25/35kV 600Amp Three Phase Sectionalizing Cabinets
Features: ND-430-MG-101-X-X, ND-450-MG-101-X-X
• One-piece design for the ND-430 and ND-450, ground sleeve is part of the
cabinet.
chopped glass spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly to their strength.
attack.
• Two stainless steel self locking cam arms hold the lid open.
• Hot-dipped galvanized MP-101 mounting plate,(also available in stainless
steel) accommodates up to three 2, 3 or 4 pt., 15/25/35kV 200A and 600A
loadbreak junctions with U-straps, except for Cooper 35kV.
ND-430-MG-101-X-X
• Optional hot-dipped galvanized MP-10135 mounting plate, (also available in
stainless steel) accommodates up to three 2, 3, or 4 pt., 35kV 600Amp deadbreak junctions with U-straps from Cooper.
• Accommodates 200A taps off of the 600A junctions.
• Below parking allows for stand-offs or feed throughs to be installed.
• ND-450 has an optional 18” or 36” high extension for extra cable bending
radius.
Benefits:
• The cabinet’s four eyebolts allow the lineperson to simply hook-up the cabinet,
position it over the cables, and place it in the excavated area for a simple
installation.
15/25/35kV 600Amp
Cabinets
Parking
Top
Width
Top
Depth
Cabinet
Height
Hot Stick
Operating
Depth
Recommended
Burial Depth
ND-430-MG-101-X-X
Below
68.5”
29.5”
53”
25.5”
ND-450-MG-101-X-X
Below
68.5”
29.5”
64.5”
29
Finish grade
approximately
6” below locking
system.
ND-450-MG-101-X-X
07/15
Page 21
15/25kV 200Amp Three Phase Roto-Cab Sectionalizing Cabinets
Features: ND-5524 Series
• One-piece design for the ND-5224 Series cabinets, ground sleeve is part
of the cabinet.
attack.
ND-552436-MG-101-X-X
ND-552436-MG-152-X-X
ND-552436-MG-PA58-X-X
• Hot-dipped galvanized MP-101 mounting plate accommodate up to three 2, 3
or 4 pt., 15/25kV 200/600A loadbreak junctions with U-straps.
• MP-101 below parking allows for stand-offs or feed throughs to be installed.
ND-552442-MG-101-X-X
• MP-152, PA58, PB58 mounting plates accommodate up to three 2, 3 or
4 pt., 15/25kV 200A loadbreak junctions with U-straps.
• The sliding rail on the 152 and PA58 allows for stand-offs or feed throughs to
be installed on the stainless steel above parking stands, or the below parking
stands on the PB58.
Benefits:
• The cabinet’s four eyebolts allow the lineperson to simply hook-up the cabinet,
position it over the cables, and place it in the excavated area for a simple
installation.
15/25kV 200Amp
Cabinets
Parking
Top
Width
Top
Depth
Cabinet
Height
Hot Stick
Operating
Depth
ND-552436-MG-101-X-X
Below
55.5”
23”
36”
23.5”
ND-552436-MG-152-X-X
Above
55.5”
23”
36”
23.5”
ND-552436-MG-PA58-X-X
Above
55.5”
23”
36”
21.5”
ND-552442-MG-101-X-X
Below
55.5”
23”
42”
23.5”
ND-552442-MG-152-X-X
Below
55.5”
23”
42”
23.5”
ND-552442-MG-PA58-X-X
Above
55.5”
23”
42”
23.5”
ND-552454-MG-101-X-X
Below
55.5”
23”
54”
23.5”
ND-552454-MG-152-X-X
Above
55.5”
23”
54”
23.5”
ND-552454-MG-PA58-X-X
Above
55.5”
23”
54”
21.5”
Page 22
ND-552442-MG-152-X-X
&
ND-552442-MG-PA58-X-X
Recommended
Burial Depth
ND-552454-MG-101-X-X
Finish grade
approximately
6” below
locking system.
ND-552454-MG-152-X-X
&
ND-552454-MG-PA58-X-X
07/15
15/25kV 200 and 15/25/35kV 600Amp Three Phase Roto-Cab Sectionalizing
Cabinets
Features:
• Two-piece design for the ND-2562448 and ND-2722850.
combination of chopped glass spray-up and hand lay-up using
woven roving glass reinforcement, which adds greatly to their
strength.
contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet
attack.
• P-107 stainless steel locking system with a silicon bronze penta-head bolt provides double
locking.
ND-2562448-MG-101-X-X
ND-2562448-MG-101-X-X & ND-2562448-MG-152-X-X:
• Hot-dipped galvanized MP-101 & MP-152 mounting plates accommodates up to three 2, 3,
or 4 pt., 15/25kV 200A loadbreak junctions with U-straps.
• Does not accommodate 200A taps off the 600A junctions.
• MP-101 below parking allows for stand-offs or feed throughs to be installed.
ND-2562448-MG-152-X-X
• MP-152 above parking allows for stand-offs or feed throughs to be installed.
• MP-152 plate can be rotated horizontally for easy junction installation.
ND-2722850:
• Hot-dipped galvanized MP-168 mounting plate accommodates up to three 2, 3, or 4 pt.,
15/25/35kV 200A loadbreak junctions. It also accommodates 200A taps off of the 600A
junctions.
• MP-168 above parking allows for stand-offs or feed throughs to be installed.
• MP-168 mounting plate can be rotated horizontally for easy junction installation.
Benefits:
• The cabinet’s four eyebolts allow the lineperson to simply hook-up the cabinet, position it
over the cables, and place it in the excavated area.
Two-Piece 15/25kV 200Amp
Cabinets
Parking
Top
Width
Top
Depth
Cabinet
Height
Hot Stick
Operating
Depth
ND-2562448-MG-101-X-X
Below
56”
24”
48”
25”
ND-2562448-MG-152-X-X
Above
56”
24”
48”
24”
Above
72”
28”
50”
28”
Two-Piece 15/25/35kV 600Amp
Three Phase
ND-2722850-MG-168-X-X
07/15
Recommended
Burial Depth
Finish grade
approximately 6”
below
locking system.
ND-2722850-MG-168-X-X
Page 23
15/25/35kV 600Amp Three Phase Roto-Cab Sectionalizing Cabinets
Features:
combination of chopped glass spray-up and hand layup using woven roving glass reinforcement, which adds
greatly to their strength.
• The exterior is applied with a Munsell green gel-coat,
which contains UV stabilizer and provides superior weather-ability and resistance to ultraviolet attack.
Standard.
ND-6830 Series:
• Aluminum PA71 or PB71 mounting plate accommodates
up to three 2, 3 or 4 pt., 15/25/35 kV 200A or 600A junctions with U-straps (accommodates 200A taps), including
Cooper 35 kV 200A/600A junctions.
ND-683042-MG-PA71-X-X
• Accommodates 200A taps off of the 600A junctions.
• The sliding rail on the PA71 or PB71 allows for stand-offs or
feed throughs to be installed on the stainless steel parking
stands either above (PA71) or below (PB71).
• ND-683054 has an optional 18” or 36” high extension for
extra cable bending radius.
Benefits:
• The cabinet’s four eyebolts allow the lineperson to simply
hook-up the cabinet, position it over the cables, and place
it in the excavated area.
15/25/35kV 600Amp
Cabinets
Parking
Top
Width
Top
Depth
Cabinet
Height
Hot Stick
Operating
Depth
Recommended
Burial Depth
ND-683042-MG-PA71-X-X
Above
68.5”
30”
42”
26.5”
ND-683054-MG-PA71-X-X
Above
68.5”
30”
53.5”
26.5”
Finish grade
approximately
6” below
locking system.
ND-683054-MG-PA71-X-X
Page 24
07/15
ND-325 (Standard) & (Multi-Point Junction Cabinet)
Features:
• Nordic cabinets are produced of fire-retardant resin and a combination of chopped glass
spray-up and hand lay-up using woven roving glass reinforcement, which adds greatly
to their strength.
• The exterior is applied with a Munsell green gel-coat, which contains UV stabilizer and
• P-107 stainless steel locking system with a silicon bronze penta-head bolt provides
double locking.
Standard: ND-325-MG-2C5A-X-X:
• Hot-dipped galvanized MP-2C5A mounting plate in the ND-325, (also availabe in
stainless steel) accommodates up to three 2, 3, or 4 pt., 15/25kV 200A loadbreak
junctions with U-straps.
ND-325-MG-2C5A-X-X
• In-line parking on the MP-2C5A allows for parking stand-offs or 2 pt. feedthroughs on
either side of the mounting plate.
Multi-Point: ND-325-MG-S102CX-X-X, ND-325-MG-X-X-X
• Accommodates a variety of 5 and 6 way 15/25/35kV multiple point junctions with 4” interface spacing from a variety of manufacturers including Elastimold, Hubbell, G&W, and
Cooper linear junctions. (Check out our website for junction accommodations)
ND-325-MG-S102CX-6252B-W3B
• Junctions without parking stands can either be mounted to a mounting plate or
mounted to the cabinet’s fiberglass mounting board with their own mounting bracket.
• Multi-Point junctions allow for different configurations of 200A and 600A interfaces for
either load or dead break elbows.
Benefits:
• The cabinet’s four eyebolts allow the lineperson to simply hook-up the cabinet, position it
over the cables, and place it in the excavated area.
Mounting Plate
Parking
Stands
Mounting
Board
Width
Hot Stick
Operating
Depth
Cabinet
Height
2C5A
In-Line
85”
22”
48”
S102CX
Below
85”
22”
48”
Based on Junction
Below
85”
22”
48”
ND-325 Cabinet
ND-325-MG-2C5A-X-X
ND-325-MG-S102CX-X-X
ND-325-MG-X-X-X
07/15
ND-325-MG-X-53594-W3B
Page 25
Cabinet Extensions
Cabinet Extensions
Features:
• Used extensively in wind farm applications where large
diameter cable needs a large expansive area for bending and
cable training.
• Cabinet extensions extend the height of the cabinet to allow
for more cable bending radius.
• The extensions allow for extra cable looping.
• In case of an elbow failure, the damaged elbow and cable can
be removed and the extra slack can be used to attach a new elbow.
ND-450-MG-101-X-X
• 18” or 36” high cabinet extensions are available for most of Nordic’s three phase
sectionalizing cabinets.
• Greater anchoring stability is obtained with an extension.
• Cabinets and extensions bolt to the bottom sides of the
cabinets, (cabinets and extensions shipped separately).
ND-450-MG-18EXT
• Bolting hardware included with the extensions.
ND-450-MG-101-X-X
ND-450-MG-36EXT
18” or 36” high cabinet extensions are available for most of our
three phase sectionalizing cabinets.
Allows for extra cable training and greater anchoring stability.
ND-2722850-MG-18EXT
18”H Ext. for ND-2722850
ND-450-MG-101-X-X mounted to
ND-450-MG-36EXT
ND-450-MG-101-X-X mounted to
ND-450-MG-18EXT
Base Width
Base Depth
Burial Depth
Per Pallet
101.5”
61.5”
18”
12
ND-2722850-MG-36EXT
36”H Ext. for ND-2722850
114”
72”
36”
8
ND-325-MG-18EXT
18”H Ext. for ND-325
123”
56”
18”
12
ND-350-MG-18EXT
87”
60”
18”
8
ND-350-MG-36EXT
93.5”
66.5”
36”
8
ND-403264-MG-18EXT
18”H Ext. for ND-403264
73.5”
64.5”
18”
7
ND-403264-MG-36EXT
36”H Ext. for ND-403264
81.5”
72.5”
36”
7
ND-450-MG-18EXT
101.5”
61.5”
18”
12
ND-450-MG-36EXT
114”
72”
36”
8
ND-552454-MG-18EXT
18”H Ext. for ND-552454
91”
65”
18”
13
ND-552454-MG-36EXT
36”H Ext. for ND-552454
96.5”
70.5”
36”
8
ND-683054-MG-18EXT
18”H Ext. for ND-683054
101.5”
61.5”
18”
12
ND-683054-MG-36EXT
36”H Ext. for ND-683054
114”
72”
36”
8
Page 26
07/15
Cabinets, Deferral
Transformer Deferral Cabinets
Features: ND-202224-MG-125-X-X
• Cabinet is produced of SMC, (Sheet Molded Compound).
• Hot-dipped galvanized MP-125 mounting plate
accommodates one, 2, 3, or 4 pt., 15/25 kV, 200/600Amp
junction with U-straps, except Cooper 35kV.
• Install it on any CBP “A” series or GS-37-43 “B & C” series
box pads.
• Stainless steel cabinet bolting hardware is included with the
cabinet.
• ND-202224 cabinet weighs only 65 lbs., so one person can
install it.
• When transformer is ready to be installed, remove the
ND-202224 cabinet and install the transformer.
• Either store the ND-202224 or install it for another deferral
application thereby saving money on buying a new
transformer.
ND-202224-MG-125-X-X attached to
CBP-37-43-15A-MG-22x24
Other deferral cabinets listed below:
ND-28-MG-103-X-X
ND-37-MG-102C-X-X & ND-37H-MG-102C-X-X
ND-301830-MG-102A-X-X
ND-250-MG-101-X-X
ND-38-MG-S108-X-X
Single Phase 15/25/kV 200Amp Deferral Cabinets
GS-Ground Sleeve
Parking
Top
Width
Top
Depth
Cabinet
Height
Hot Stick
Operating Depth
ND-202224-MG-125-X-X
Below
21”
21”
24”
22”
ND-28-MG-103-X-X (GS w/22”x24” openings)
In-Line
25”
29”
22”
29”
ND-37-MG-102C-X-X (GS w/22”x24” openings)
In-Line
37”
29.5”
22”
29.5”
ND-37H-MG-102C-X-X (H=Hinged)
In-Line
37”
29.5”
22”
29.5”
ND-301830-MG-102A-X-X
In-Line
30”
19.5”
30.5”
19”
In-Line
37.5”
37.5”
23”
37”
Below
53.5
26”
34.5”
23”
Single Phase 15/25/35kV 600Amp Deferral Cabinets
ND-38-MG-S108-X-X (GS w/26”x32” openings)
Recommended
Burial Depth
Finish grade
approximately
6” below
locking system
with ground
sleeve.
Three Phase 15/25kV 200Amp Deferral Cabinets
ND-250-MG-101-X-X
07/15
Pad-Mount
Page 27
Cabinets, Sub-Surface Sectionalizing
15/25kV 200Amp Sub-Surface Sectionalizing Cabinets
Features:
attack.
• These box pads are heavy duty 1/4” thick, produced of fire-retardant resin
and a combination of chopped glass spray-up and hand lay-up using 18
ounce woven roving glass reinforcement.
GSLBJ-363632-MG-S103-X-X
• The SSMP-103 mounting plate has in-line parking to allow for stand-offs or
feed throughs to be installed.
• The covers have a 2” down-turned lip around the outer perimeter for added
security.
Single-Phase Features:
• The GSLBJ-363632-MG-S103-X-X is designed for sectionalizing or
deferral with subsequent installation of a single-phase transformer.
• Stainless steel SSMP-103 mounting plate accommodates all 15/25kV,
200/600A junctions with U-straps, except Cooper 35 kV.
• Four brass penta-head recesses are installed, with four 3/8” x 1 1/2”
stainless steel penta-head bolts included, for securing the cover to the
box pad.
Three-Phase Features:
• GSLBJ-803636-MG-S103-X-X will accommodate three 2, 3, or 4-point
15/25kV, 200A junctions with U-straps.
• The GSLBJ-805436-MG-S103-X-X will accommodate three 2, 3, or
4-point 15kV or 25kV 200/600A loadbreak junctions with U-straps, except
Cooper 35kV.
• GSLBJ-805436-MG-S103-X-X will accommodate 200A taps off of the
600A junctions.
• Six brass penta-head recesses are installed, with six 3/8” x 1 1/2” stainless
steel penta-head bolts included, for securing the cover to the box pad.
Parking
Accommodates
2-4 pt. 15/25kV
200Amp LBJ’s
Mounting
Board
Width
Hot Stick
Operating
Depth
Height
Mounting
Board
Angle
In-Line
Yes
23.5”
30”
32”
30°
In-Line
Yes
72”
28”
36”
20°
In-Line
Yes
72”
45”
36”
20°
Page 28
07/15
Cabinets, Vacuum Switch
Vacuum Interrupter Switch Cabinets
Features:
• Nordic cabinets are produced of fire-retardant resin and a combination
ultraviolet attack.
ND-362436-MG-UNI2-X-X
• P-107 stainless steel locking system with a silicon bronze penta-head
bolt provides double locking.
• Cabinet with interrupter gives the customer an option for line fault
protection.
• Strong strut bracket supports horizontally mounted interrupter switches.
• Stationary bracket accommodates Elastimold bolt patterns.
(Brackets do not include interrupter mounting hardware)
• Cabinet extensions are available in 18” or 36” heights for more cable
bending radius for the ND-362454-MG-UNI2-X-X model.
Features: ND-403264-MG-UNI4-X-X
• Strong strut bracket supports interrupter switches in either single
(vertical or horizontal) or three phase vertical mount applications.
• Adjustable brackets in the ND-403264-MG-UNI4-X-X gives instant
bracket adaptability to Elastimold or G&W bolt patterns.
bending radius.
Features: ND-683054-MG-UNI4-X-X
• Strong strut bracket supports three phase interrupter
switches in vertical mount applications.
• Strut bracket system has 4 vertically adjustable horizontal
brackets that accommodate a variety of manufacturer’s
vacuum switch interrupter’s bolt patterns.
bending radius.
07/15
Page 29
§Covers, Ground Sleeve
Covers for Ground Sleeves
Features: Standard Covers
hardware.
• The exterior is applied with a Munsell green
gel-coat (not applicable to the GSC-37-43-MG
cover), which contains UV stabilizer and provides
superior weather-ability and resistance to ultraviolet
attack.
• The standard cover is fabricated of one layer of 1/2”
plywood encapsulated in fiberglass, using fireretardant resin and chopped glass and 18 ounce
woven roving reinforcement.
Standard Cover GSC-75-72-MG
• The word “ELECTRIC” can be printed on the cover
for an additional charge.
• Covers are available for all box pads and ground
sleeves.
• Four brass penta-head recesses are installed for
securing the cover to the box pad.
• Covers come with four 3/8” x 1 1/2” stainless steel
penta-head bolts.
• For larger sized covers, two layers of 1/2” plywood
are standard, as are six to eight penta-head
recesses and bolts.
• For retrofitting to box pads or ground sleeves that
were not furnished with inserts, Nordic can provide
stainless steel 3/8” and 1/2” floating nut inserts for
installing the cover.
GSC-37-43-MG Cover
The word
“WARNING ELECTRIC”
is imprinted on every
GSC-37-43 cover.
Features: GSC-37-43-MG
• UV stabilizers are contained in the resin to provide
protection from ultraviolet light attack.
• The top of the cover is a textured non-skid diamond
tread surface, which provides a safe operating
platform in all types of weather.
• The GSC-37-43 covers are produced by a process
known as cold pressed molding.
• Molded-in penta-head cups in the cover match the
CBP’s & GS-37-43 Series insert patterns for installation, bolting hardware included with each cover.
Page 30
Four brass penta-head recesses are
installed for securing the cover to the
box pad. For larger covers, six to eight
penta-head recesses and bolts are
installed.
07/15
Features: Extenders
• Have a damaged box pad or a change in grade level?
• Ground sleeve extenders work great where you can shut off the power, excavate
around the damaged sleeve, and install a ground sleeve extender over it.
GSE-4A-MG-22x24
• If the grade line has come up over the years, these units extend the ground
sleeve up another 4” above grade
GS-37-43-32C-CE-2-MG22x24
• The GSE-4A-MG-22x24 and GSE-4F-MG-26x30 go over box pads with a
37” x 43” top surface.
• Covers up a damaged box pad and raises it up 4” at the same time.
Features: Adapters
GSA-37-43-MG-21x10
• The GSA-37-43-MG-21x10 adapter is designed to fit on the
GSLBJ-37-43-32C-CE-2-MG-22x24.
• This unit also accommodates the ND-301830 in either a single phase cabinet or
tap pedestal.
GS-37-43-32C-CE-2-MG22x24 with
GSE-4A-MG-22x24
GSE-4F-MG-26x30
GSA-37-43-MG-21x10
GSLBJ-37-43-32C-CE-2MG-22x24
• Because of its smaller top opening this adapter also accommodates single phase
metal sectionalizing cabinets.
Features: Adapters
GSA-36-36-MG-25x10
• The GSA-36-36-MG-25x10 provides an adapter for the GS-80-36-36-2O-MG-TS.
• With the adapter mounted to the box pad, the ND-301830-MG-102A-X-X can be
mounted to the adapter.
GSLBJ-37-43-32C-CE2-MG-22x24 with the
GSA-37-43-MG-21x10
mounted to it.
• The ND-301830-MG-102A-X-X can be used as a single phase sectionalizing
cabinet.
• The ND-301830-MG-102A-X-X can also be used as a secondary tap pedestal
called the ND-301830-MG-X-L750350P-X.
GSA-36-36-MG-25x10
• Other metal single phase sectionalizing cabinets can be mounted to the
GSA-36-36-MG-25x10.
Replacement Ground Sleeve/Transformer Pads
Features: RGS-30-18-18-MG-21x10, RGS-61-18-18-MG-55x10, RGS-37-4310-MG-24x30, and RTP-42.5-45.5-7-MG-22x24.
GS-80-36-36-2O-MG-TS
GS-80-36-36-2O-MG-TS
with
GSA-36-36-MG-25x10
mounted to it on the right side
• These replacement ground sleeves can be installed directly over rusted metal
ground sleeves or after removal of the damaged sleeves.
• Front partition is removable for electrical cables to slide through during installation
without disconnecting the power.
GSLBJ-37-43-32C-CE2-MG-22x24 with the GSA37-43-MG-21x10 and the
ND-301830-MG-102A-X-X
mounted to it
GS-80-36-36-2O-MG-TS with
GSA-36-36-MG-25x10 &
ND-301830-MG-102A-X-X.
RGS-30-18-18-MG-21x10
RGS-61-18-18-MG-55x10
• The two-piece units are joined by driving 3/8” stainless steel bolts into the floating
nut assemblies on the sides and flange of the sleeve.
RGS-37-43-10-MG-24x30
RTP-42.5-45.5-7-MG-22x24
07/15
Page 31
Flexi-Flags, Curb, and Cabinet Markers
Hydrant Flexi-Flags, Curb Markers, and Cabinet Markers
Features:
• Wound galvanized spring steel is a tough material for all types of
weather.
• The one-piece staff, coil spring or looped end is 53” or 72” tall.
• The HDPE flag provides approximately 20 square inches of surface
area.
• Economical, easy to install, lasts for years.
FF-1L and FF-2L Looped Hydrant Flexi-Flags
• Flag has a looped end.
• Simply remove the hydrant’s housing cover and install the flag’s loop
over the threaded coupling, reinstall the cover with the flag.
•FF-1L - 53” High
•FF-2L - 72” High
FF-1L installed
FF-1 and FF-2 Hydrant Flexi-Flags
• The Flexi-Flag is field tested with staff, bracket, and spring made of
wound galvanized spring steel, topped with an orange HDPE flag.
•FF-1 - 53” Hydrant Marker
•FF-2 - 72” Hydrant Marker
CM-1 and CM-2 Curb Marker Flexi-Flags
• Snow removal personnel also benefit from seeing the brightly
colored flag and avoid hitting a hydrant or curb with their snowplows.
•CM-1 - 53” Curb Marker
•CM-2 - 72” Curb Marker
FF-1 installed
FF-1C and FF-2C Cabinet Marker Flexi-Flags
• The Nordic Cabinet Marker helps to identify the location of cabinets
and pedestals hidden by snow, brush, weed growth, or in crop fields.
•FF-1C - 53” Cabinet Marker
•FF-2C - 72” Cabinet Marker
CM-1 installed
Page 32
FF-1C installed
07/15
Ground Sleeves, 1 & 3 Phase Sectionalizing
Ground Sleeves for Single & Three Phase Enclosures
CGS-30-18-18-MG-21x10
Features:
GS-30-18-30-MG-21x10
GS-61-18-18M-MG-55x10
Installed GS-61-18-18M-MG-55x10
• Rust free and very little maintenance is required.
• CGS (compression ground sleeve) is manufactured of SMC (Sheet Molding Compound). SMC is a thermosetting
compound which is pre-mixed with pigments that are molded into the fiberglass and cannot peel. Fire retardant and UV
additives are permanently molded in throughout the laminate.
• GS units are produced of fire-retardant resin and a combination of chopped glass spray-up and hand lay-up using 18
ounce woven roving glass reinforcement for a 1/4” nominal fiberglass thickness for great strength.
• M-Medium weight units have 3/16” nominal fiberglass thickness.
• Units can be pre-drilled to accommodate sectionalizing cabinets.
• Munsell green gel-coat is used for superior weather-ability.
• Labor saver; most units can be easily lifted by one person and installed the same day.
Single and Three Phase Ground Sleeves
CGS-30-18-18-MG-21x10
GS-31-19-18M-MG-22x13.5
GS-49-15-18M-MG-40.5x10.5
GS-67-23-30-MG-57x18
GS-10-12-18-MG-6x8
GS-31-23-18M-MG-22x18
GS-49-15-30-MG-40x10
GS-67-24-24M-MG-60x14
GS-18-18-18M-MG-9x9
GS-31-23-30-MG-22x17.5
GS-49-18-18M-MG-38x10.5
GS-70-18-18-MG-64x12.5
GS-19-10-18M-MG-15x6
GS-32-12-24-MG-24x4
GS-49-23-18M-MG-39.5x17
GS-71-25-24-MG-61.5x12.5
GS-24-22-18M-MG-17x16
GS-32-16-18M-MG-24x9
GS-49-23-30-MG-40x17.5
GS-72-25-48-MG-63x17
GS-24-22-30-MG-16x17.5
GS-32-16-30-MG-26x12
GS-61-15-18M-MG-53x11
GS-78-20-18-MG-72x14
GS-24-24-30-MG-16x16
GS-34-25-24-MG-26x17
GS-61-15-30-MG-52x10
GS-78-24-36-MG-70x16
GS-25-15-18M-MG-16x10
GS-35-20-18M-MG-25x11.5
GS-61-18-18M-MG-55x10
GS-85-23-18-MG-75x17
GS-25-19-18M-MG-19x13
GS-35-35-30-MG-27x27
GS-61-18-26-MG-55x10
GS-85-23-30-MG-73x16
GS-26-15-18M-MG-19x8
GS-36-24-24-MG-31x19
GS-61-18-30-MG-54x11
GS-96-27-30-MG-89.5x21
GS-26-18-18M-MG-17x9
GS-36-26-18M-MG-30x20
GS-61-20-18M-MG-55x10
GS-27-20-18M-MG-17.5x11.5
GS-37-23-18M-MG-28x18
GS-61-37-15-MG-52x32
GS-27-20-26-MG-18x12
GS-37-23-30-MG-27.5x17
GS-64-18-18M-MG-56.5x10.5
GS-30-18-24-MG-20x9
GS-38-20-18M-MG-30x12
GS-64-18-30-MG-56x13
GS-30-18-30-MG-21x10
GS-44-18-18M-MG-37x9.5
GS-64-20-18M-MG-57.5x12.5
GS-30-20-18M-MG-21x10
GS-44-26-24-MG-37x20
GS-64-20-30-MG-55x10
GS-30-20-30-MG-23.5x13
GS-44-44-18M-MG-32x32
GS-65-20-18M-MG-58x12
GS-31-10-36M-MG-27x6
GS-44-44-36-MG-34x34
GS-67-23-18M-MG-58x16.5
07/15
Page 33
Ground Sleeves, Traffic
Ground Sleeves for Traffic Equipment
GST-24-22-18-GR-17x16
GST-30-18-24-GR-24x13
GST-90-60-5-MG-20x10.5
Features:
• These ground sleeves are produced of fire retardant resin and a combination of chopped glass spray-up and hand
lay-up using 18 oz. woven roving glass reinforcement.
• The exterior is applied with a Mist Gray (Concrete Color) gel-coat, which contains UV stabilizer for superior
weatherability.
• Stainless Steel floating nut inserts can be installed to match traffic control bolting patterns for an additional cost.
• The GST-90-48-5-MG-20x10.5 and GST-90-60-5 each feature a large walking surface for workers to step on and get
out of the dewy grass or mud.
• Other gel-coat colors available.
• Please see our Cabinet Cross Reference Chart below. Common traffic signal cabinets are listed with the Nordic
ground sleeve that will accommodate it.
Cabinet Cross
Reference Chart
Cabinet Type
W
D
Nordic Product
Nordic Product
L
W
H
Top
Opening
330
22”
18”
GST-24-22-18-GR-17x16
GST-24-22-18-GR-17x16
24”
22”
18”
17” x 16”
332
24”
30”
GST-36-24-24-GR-22x9
GST-24-22-24-GR-17x16
24”
22”
24”
17” x 16”
334
24”
30”
GST-36-24-24-GR-22x9
GST-25-25-24-GR-12x12
25”
25”
24”
12” x 12”
337
20”
17”
GST-24-22-18-GR-17x16
GST-30-18-18-GR-24x13
30”
18”
18”
24” x 13”
345
24”
30”
GST-36-24-24-GR-22x9
GST-30-18-24-GR-24x13
30”
18”
24”
24” x 13”
333SD
44”
29”
GST-50-30-20-GR-28x22
GST-36-24-18-GR-22x9
36”
24”
18”
22” x 9”
336A
24”
20”, 22”
GST-24-22-18-GR-17x16
GST-36-24-24-GR-22x9
36”
24”
24”
22” x 9”
44”
26”
18”
20” x 12”
336S
24”
20”, 22”
GST-24-22-18-GR-17x16
GST-44-26-18-GR-20x12
G
25”
16”
GST-30-18-24-GR-24x13
GST-44-26-24-GR-20x12
44”
26”
24”
20” x 12”
50”
30”
20”
28” x 22”
M
30”
17”
GST-30-18-24-GR-24x13
GST-50-30-20-GR-28x22
M36
36”
17”
GST-36-24-24-GR-22x9
GST-71-26-24-GR-55x12.5
71”
26”
24”
55” x 12.5”
GST-90-48-5-MG-20x10.5
90”
48”
5”
20” x 10.5”
GST-90-60-5-MG-20x10.5
90”
60”
5”
20” x 10.5”
P38
38”
26”
GST-44-26-24-GR-20x12
P44
44”
26”
GST-44-26-24-GR-20x12
P44 Super
59”
26”
GST-71-26-24-GR-55x12.5
R38
38”
26”
GST-44-26-24-GR-20x12
R44
44”
26”
GST-44-26-24-GR-20x12
Page 34
07/15
Hardware & Miscellaneous Accessories
Hardware
Features: AB-2
Features: CAS-1
• Anchor bracket is designed
to tie down transformers or
switchgear.
• Enables various box pad
insert patterns to
accommodate more sizes of equipment.
• Manufactured of 3/8” thick carbon steel, hot-dipped galvanized.
• Hot-dipped galvanized
steel cabinet anchors
allow the customer to
bolt a Nordic fiberglass
sectionalizing cabinet to
a cement pad.
(CAS-1, 4 anchors)
• Comes with one 3/8” stainless steel bolt, one flat washer, and
one lock washer.
• Measures 1 1/2” x 6 1/4”.
• Bend in the bracket raises it 1/4” from the pad.
• Slot in the AB-2 bracket is 1/2” wide x 4 1/2” long.
• Can be factory installed on your box pad or shipped separately.
Features: Cable Entrance w/hardware
Features: PH-1 (Penta-Head
Wrench)
• Heavy
duty
chrome
plated.
• Easy to
use.
• Use it on
transformers, switchgear, and other
enclosures with penta-head bolt locking.
• Black plastic cover can be installed inside
a secondary pedestal for a cable
entrance cover.
• Long lasting construction
• Maximum cable hole dimension is 2” OD.
• Includes mounting hardware.
Features: FN-Floating Nut Assemblies
• If you don’t have access to the hex nut, this is the perfect way to tighten
down almost anything.
• The square brass nut (FN-38=3/8” sq. nut, FN-12=1/2” sq. nut) is held by
a stainless steel nut retainer and covered with a SST flat plate.
• Two #10 bolts with lock washers and #10 nuts can be installed almost
anywhere.
FN-38
FN-12
FN-38 & FN-12 Floating Nut Assemblies
Features: Nordic Repair Kits
• NRK-2 repair kit gives the customer the
necessary materials to patch up a small
fiberglass tear or puncture.
• NRK-3 Repair Kit covers up a damaged
box pad corner. Includes fiberglass corner,
silicone paintable clear caulk, and bolt kit.
07/15
NRK-2 Repair Kit
NRK-3
Page 35
Hardware
Features: Transformer Deferral Brackets
• TDB-2 can be installed in back corner of the GS-37-43-32A-CE-2 or the
GS-37-43-32C-CE-2 box pads.
• The TDB-2-C15 can be installed in the back corner of the 15” high CBP “A”
top opening units.
• TDB-2-C24 can be installed in the back corner of the 24” high CBP “A” top
opening units.
• TDB-3 can be installed in back corner of the GS-37-43-32A-CE-2 or the
GS-37-43-32C-CE-2 box pads.
• When the transformer is installed, the bracket and the box pad cover can be
used in another temporary installation.
TDB-2
• Savings will be realized by delaying the investment in a transformer until it is
needed. Also, savings will be made by not having to invest in or excavate a
looping pedestal for a temporary looping arrangement.
TDB-2-C15
TDB-2-C24
TDB-3
Features: Penta-Head Bolts
• 304 Stainless steel penta-head bolts available in a variety of diameters and lengths. (Actual sizes not shown)
PH-4
Dia.
Thread
Length
Description
PH-4
3/8”
16 UNC
1.405”
Washer and Point
PH-6
1/2”
13 UNC
1.50”
No Washer or Point
PH-7
3/8”
16 UNC
1.75”
Washer and Point
PH-8
1/2”
13 UNC
1.75”
No Washer or Point
PH-6
PH-7
Page 36
Penta-Head
Bolt
(Stainless
Steel)
PH-8
07/15
Hardware
Features: Fast-Patch
Damaged
Product
• Easy application - just cut, peel and stick - finished.
• Extremely durable, Fiberglass, reinforced Polyester
• Flexible and waterproof
• Weather and UV resistant
• Can be drilled, sanded, and painted in less than an hour
• Resistant against many chemicals, solvents and oils
• Constantly Temperature resistant from -40°F to 392°F
• No shrinkage or expansion during the application or after curing
• Bonds to fiberglass, metal and PVC surfaces
• Fast curing (starting with 5 minutes depending on UV intensity)
Applications:
Fast-Patch
Applied
• Fiberglass: Box pads, ground sleeves, and sectionalizing cabinets.
Metal: Transformers, switchgear, sectionalizers, meters, and conduit.
• PVC: Riser guards and conduit.
Application Methods:
1.Surface should be cleaned, dry and free of contaminates.
2.Remove black protective sheet. Cut Fast-Patch into any size you want without
exposing to UV/Sunlight. Place remaining material back in black protective sheet.
3.Remove white backing tape to expose the strong adhesive. Apply patch then
remove transparent film backing on other side after application.
4.Apply Fast-Patch to repair area with sticky side down. Press firmly and expose to
UV-/sunlight. Curing times depending on UV intensity between 5 minutes
(sunny) and 50 minutes (cloudy).
Fast-Patch
Painted
The Fast-Patch (FP) is available in three sizes (inches):
Paint sold separately
Not required
• FP-3x6
• FP-6x9
• FP-9x12
07/15
Page 37
Hill Holders
Hill Holders
Features: Hill Holders
• Heavy duty 1/4” thick hill holders are
produced of fire retardant resin and a
combination of chopped glass spray-up
and hand lay-up using woven roving glass
reinforcement, which contributes greatly to
their strength.
• The exterior is applied with a Munsell
green gel-coat which contains UV stabilizer
in addition to pigments and polyester resin
for superior weatherability. The exterior
has a textured gel-coated finish and the
interior has a smooth gel-coated finish.
NHH-16-46-52-MG
NHH-20-54-52-MG
NHH-32-46-52-MG
NHH-32-54-52-MG
• The NHH-32-46-52 and NHH-32-54-52MG have two horizontal ribs on the back
side for added strength.
• The 2” flange around the entire perimeter
provides stability.
B
A
C
Hill Holder
A
Back Height
B
Back Width
NHH-16-46-52-MG
16”
46.5”
52”
NHH-20-54-52-MG
20”
54”
52”
NHH-32-46-52-MG
32.5”
46.5”
52.5”
NHH-32-54-52-MG
32.5”
54”
52”
Page 38
C
Side Extensions
Installed NHH-32-54-52-MG
07/15
Pedestals, Hand Holes
Hand Holes, Plastic and Fiberglass
PHH-161912-MG
PHH2-161912-MG
PHH-161918-MG
Features: Plastic Hand Holes
PHH2-161918-MG
PHH-212115-MG
PHH2-212115-MG
• Plastic hand holes are made from
copolymer polypropylene and designed for flush burial.
• The Munsell green pigment is blended throughout the material, which contains
UV stabilizer for weather-ability.
• Units include a flat cover. “ELECTRIC” is imprinted on standard cover.
PHH Lock
• GSHH-ground sleeve hand hole, HHC-hand hole cover, HHC2-hand hole
cover with double lock, PHH-plastic hand hole, PHH2-plastic hand hole with double lock.
PHH2 Lock
Features: Fiberglass Hand Holes
• These ground sleeves are produced of fire retardant resin and a combination of chopped glass spray-up and hand layup
using 18 oz. woven roving glass reinforcement for a 1/4” fiberglass nominal thickness throughout the part.
• The exterior is covered with a Munsell Green gel-coat, which contains UV stabilizer for superior weather-ability.
• M-Medium Weight, 3/16” thick nominal fiberglass thickness.
LxWxH
Top Opening
Description
GSHH-25-16-16M-MG-21x12
Nordic Products
25 x 16 x 16
21 x 12
Base with flat cover
GSHH-25-19-18-MG-19x13
25 x 19 x 18
19 x 13
GSHH-30-18-18-MG-24x12
30 x 18 x 18
24 x 12
GSHH-37-23-18-MG-31x17
37 x 23 x 18
31 x 17
HHC-1619-MG
16 x 19
N-A
Flat cover only
HHC-2121-MG
21 x 21
N-A
Flat cover only
HHC2-1619-MG
16 x 19
N-A
Flat cover only, 2 Lock
HHC2-2121-MG
21 x 21
N-A
Flat cover only, 2 Lock
PHH-161912-MG
16 x 19 x 12
12 x 16
PHH-212115-MG
21 x 21 x 15
18 x 18
PHH-161918-MG
16 x 19 x 18
12 x 16
GSHH-25-16-16M-MG-21x12
PHH2-161912-MG
16 x 19 x 12
12 x 16
Base with flat cover, 2 Lock
PHH2-161918-MG
16 x 19 x 18
12 x 16
PHH2-212115-MG
21 x 21 x 15
18 x 18
HHC-1619-MG
07/15
HHC2-1619-MG
HHC2-2121-MG
HHC-2121-MG
Page 39
Hand Holes, Below Grade Secondary Pedestals
P-65-LID-MG
P-60-MG
(Inner & Outer Bell
w/lid)
P-63-MG
(Inner Bell w/lid)
P-65-MG
(Outer Bell w/lid)
P-60-Outer Bell
Features: P-60 Series
• The P-60 and P-65 pedestals are produced of compression-molded fiberglass.
• The green pigment is permanently molded into the fiberglass and cannot peel. Will not rust or
corrode and resists ultraviolet attack.
• The word “Electric Service” is embossed on the lid’s top.
• Units are 15” high, 14” diameter.
• P-60 employs the air bell principle for maintaining watertight compartment for cable splices.
Continuous submersion tests have shown that the P-60, under six feet of water, allows only 2.3
inches of water to rise in the enclosure.
• A single lock on the P-60/65 reduces service and inspection time.
• The P-60 pedestal provides safe, enduring bell type housing for splices in underground cables.
• The P-60 is composed of two close-fitting pieces, the P-63 and outer shell. The unit is light
enough for one person to complete the installation job in one trip to the site.
• P-60 can be flush-mounted at ground surface, partially or fully buried, or surface-mounted.
• P-65 is a pedestal with a lid and outer sleeve.
• P-63-MG (Cover and inner bell replacement for P-60-MG, both cover and inner bell are one piece)
Top Dimension
Height
P-60-MG, inner & outer bell with lid
14” Dia.
16.5” w/lid
P-63-MG, inner bell with lid
14” Dia.
15”
Pedestals
Locking System
Tamper Proof Single Lock
P-65-MG, outer bell with lid
14” Dia.
16.5” w/lid
Page 40
07/15
Pedestals, Looping
Looping Pedestals
Features: Looping Pedestals
• Rigid fiberglass construction using fire retardant resin and a combination of chopped glass spray-up and hand layup
using woven roving for high strength.
• The exterior is with a UV stabilized Munsell green gel-coat for superior weather-ability and protection from ultraviolet
light.
• Non-conductive and non-corrosive.
LP-77-MG Features:
• Designed for looping 15kV primary cable at points where future plans call for installation of additional equipment.
• Dimensions are 30” long x 8” deep x 30” high with a 5” flange around the bottom perimeter for excellent stability.
LP-88-MG Features:
• Designed for looping 25kV primary cable at points where future plans call for installation of additional equipment.
• Dimensions are 53” long x 23” deep x 47” high with a 5” flange around the bottom perimeter for excellent stability.
LP-77-MG
LP-88-MG
07/15
Page 41
Pedestals, Secondary
Pedestals, Plastic
Features: PSP-151530-MG-L6350 or PSP-151530-MG-L6600
• Rust free materials and stainless steel hardware.
• Copolymer polypropylene pedestals are manufactured by an injection molding
process with UV stabilized material. Polypropylene pedestals resist fertilizers, salt
air, and ultraviolet attack.
• The green pigment is permanently molded into the copolymer polypropylene and
can-not peel or rust.
PSP-151530-MG-L6350
• “WARNING”, “ELECTRIC”, is molded into the pedestal top for easy identification.
• Top cover has room for labels in the front.
• The top is secured to the base by a flange molded into the rear of the pedestal top
and a penta-head bolt and hasp on the front.
• Accommodates three 6 port 350MCM or 600MCM connectors.
• Clear plastic covers included when connectors are ordered.
PSP-151530-MG-L6600
• Optional cable entrance cover available.
• All locking hardware is stainless steel.
Features: PSPF Series & PSPS Series
PSP-151530-MG-CE
• Linear low density polyethylene material is UV stabilized.
• “ELECTRIC” is molded into the pedestal top for easy identification.
• There is an 8” x 10” label area molded in.
PSPF-101538-MG-L6350
• Accommodates three or four 6 port 350 or 500 MCM connectors.
• Clear plastic covers included when connectors are ordered.
• All locking hardware is stainless steel.
• Suggested burial depth up to the molded in “GROUND LINE”.
• Molded step design resists deflection when buried.
PSPF-101538-MG-CE
• PSPF Series has a flared bottom design allows for ample cable training, increased
stability in a variety of soil conditions, and pedestal stacking.
PSPS-101544-MG-X
Height
Top Lid
Base
Height
Suggested
Burial Depth
Connectors
PSP-151530-MG-L6350
30”
15” x 15” x 15”
15”
12”
3 Lay-in, 6 port, 350MCM
PSP-151530-MG-L6600
30”
15” x 15” x 15”
15”
12”
PSPF-101538-MG-X
38”
10” x 15” x 17”
35.5”
16”
None
PSPF-101538-MG-L6350
38”
10” x 15” x 17”
35.5”
16”
PSPF-101538-MG-4L6350
38”
10” x 15” x 17”
35.5”
16”
PSPF-101538-MG-6500
38”
10” x 15” x 17”
35.5”
16”
3, 6 port, 500MCM
PSPF-101538-MG-46500
38”
10” x 15” x 17”
35.5”
16”
4, 6 port, 500MCM
PSPS-101544-MG-X
44”
10” x 15” x 22”
35.5”
16”
X-None, however, available with
connectors like the PSPF Series
Pedestals
Page 42
07/15
Pedestals, PSP Series
Features:
• Copolymer polypropylene pedestals are manufactured by an
injection molding process with UV stabilized material. Polypropylene
pedestals resist fertilizers, salt air, and ultraviolet attack.
• The green pigment is permanently molded into the copolymer
polypropylene and can-not peel or rust.
PSP-151530-MG
PSPX-151530-MG
PSPX2-151530-MG
• “WARNING”, “ELECTRIC”, is molded into the pedestal top for easy
identification.
• Top cover has room for labels in the front.
• The top is secured to the base by a flange molded into the rear of the
pedestal top and a penta-head bolt and hasp on the front.
PSP-91330-MG
PSPX-91330-MG
PSPX2-91330-MG
PSPX-91336-MG
PSPX2-91336-MG
• Ribs and steps are molded into the pedestal for rigidity. This design resists
deflection in a buried position and ensures the base and lid a unified
connection after servicing.
Suggested
Burial
Depth
Lock
Height
Base
Height
PSP-151530-MG
Horizontal
30”
15”
12”
PSP-91330-MG
Horizontal
30”
12”
9”
36”
18”
15”
Pedestals
PSP-91336-MG
PSP-91336-MG
Horizontal
PSPB-161912/18-MG
Base Only
12”-18”
PSPB-212115-MG
Base Only
15”
PSPT-151515-MG
Top Only
15”
PSPT-91318-MG
Top Only
18”
Cable Entrance Cover:
PSP-91330-MG-CE
Pedestals convertible to Hand Holes
PSPX-151530-MG
Vertical
30”
15”
12”
PSPX2-151530-MG
Double
30”
15”
12”
PSPXB-212115-MG
Base Only
PSPXT-151515-MG
Top Only
15”
PSPX-91330/36-MG
Vertical
30”-36”
12”-18”
9”-15”
PSPX2-91330/36-MG
Double
30”-36”
12”-18”
9”-15”
PSPXB-161912-18-MG
PSPXT-91318-MG
15”
Base Only
Top Only
PSP Lock
12”-18”
18”
PSPX domed pedestals are convertible to hand holes. The vertical locking
mechanism bolts to the base flange. The domed cover can be removed and a
flat cover (HHC-2121 or HHC-1619), can be attached to the base. HHC2-2121
and HHC2-1619 can be used as covers for the PSPX2 pedestals, PSPXTplastic secondary pedestal convertible top, X-convertible, T-Top, PSPXB-plastic
secondary pedestal convertible base, B-Base, PSPX-plastic secondary pedestal convertible to a hand hole.
PSPX Lock
PSPX2 Lock
•
Black plastic cover can be
installed inside a secondary
pedestal for a cable entrance
cover.
•
Maximum cable hole
dimension is 2” OD.
•
Includes mounting hardware.
PSP Lock:
• Horizontal lock; pentahead bolt enters a plastic
receiver in base to hold in
place.
• Hasp is riveted to base.
• Hasp tab has hole for pad
locking lid to base.
PSPX Lock:
• Vertical single locking
mechanism bolts to the
base flange.
PSPX2 Lock:
• Vertical double locking
with a bit on the lid and
base to allow pad-lock
shaft to slide through for
padlocking.
07/15
Page 43
Pedestals, P-50 Series
Features:
• Rust free SMC and stainless steel hardware.
• The P-50 and P-55 Series are manufactured of
compression molded fiberglass (SMC).
• Fire retardant and UV additives are permanently
molded in throughout the laminate.
• Pigment is permanently molded into the fiberglass and
the fiberglass does not peel, providing a maintenance
free pedestal for many years.
• Fiberglass pedestals resist fertilizers, salt air, and
ultraviolet attack.
P-50-MG
P-50-P-MG PR-50-MG
P-55-MG
P-55-P-MG PR-55-MG
• Available in Munsell Green color.
• Two sizes of Nordic pedestals, for installation with
anchoring devices, are available for above ground
housing of cable splices.
• The top section is removable for easy access to
cables.
• Stakes are available for added stability when installed.
• Recessed penta-head locking is an option.
Hasp Lock
Penta Head
Lock
Installed PR-50
Hasp & Penta
Head Lock
Pedestal
Top
Dimension
Height
Above
Ground
Below
Ground
Locking
System
P-50-MG
8” x 8”
44”
24”
20”
Hasp
P-50-P-MG
8” x 8”
44”
24”
20”
Penta-Head
PR-50-MG
8” x 8”
44”
24”
20”
Hasp &
Penta-Head
P-55-MG
8” x 8”
44”
Installed PR-55
34”
10”
P-50-MG-P-52
PR-50-P-51-MG
Stakes
P-50-MG-P-53
Description
Dimension
Hasp
P-51
Fiberglass Anchor
19” x 2” x 2”
P-52
Galvanized Steel Stake
48” Long
P-53
60” Long
P-54
72” Long
P-55-P-MG
8” x 8”
44”
34”
10”
Penta-Head
PR-55-MG
8” x 8”
44”
34”
10”
Hasp &
Penta-Head
Page 44
07/15
Pedestals, PRMC Series
Features:
• PRMC series is manufactured of compression-molded fiberglass (SMC).
• Fire retardant and UV additives are permanently molded in throughout the
laminate.
• Pigment is permanently molded into the fiberglass and the fiberglass does not
peel, providing a maintenance free pedestal for many years.
• Fiberglass pedestals resist fertilizers, salt air, and ultraviolet attack.
• Available in Munsell Green color.
• Stainless steel and aluminum hardware provide long term protection against
rust.
• “ELECTRIC” is molded in raised lettering on the top lid.
PRMC-150-MG
• A 3” flange around the perimeter provides stability when buried.
• P-109 locking assembly for safety.
Cable Entrance
Cover:
PRMC-160-MG
PRMC-170-MG
PRMC-190-MG
•
Black plastic cover can be
installed inside a secondary
pedestal for a cable entrance
cover.
•
Maximum cable hole
dimension is 2” OD.
•
Includes mounting hardware.
PRMC-150-MG-CE
Height
Top Cover
Dimensions
Lid
Height
Base
Height
Above
Ground
Below
Ground
Locking
System
PRMC-150-MG
30”
9” x 14” x 18”
18”
12”
21”
9”
P-109
PRMC-160-MG
24”
9” x 14” x 12”
12”
12”
15”
9”
P-109
PRMC-170-MG
30”
9” x 14” x 12”
12”
18”
15”
15”
P-109
15”
P-109
Pedestal
PRMC-190-MG
36”
9” x 14” x 18”
18”
18”
21”
07/15
Page 45
Pedestals, Meter
Meter Pedestals, Plastic
Features: MPP-141480-MG-X
• Linear Low Density Polyethylene Material is UV stabilized (Munsell Green
Color).
• Trailer Parks, RV Campgrounds, and townhouses now have a plastic
pedestal that can accommodate up to three meters or other pieces of
equipment.
• Easy to drill through the plastic pedestal for quick meter installations.
• Install up to 3 Meters or other equipment.
• 14” x 14” x 80” tall with a 14” x 38” meter mounting surface on 3 sides.
• Meters not included.
• Service entrance door is made of a high density polyethylene material with
a smooth finish. Includes a stainless steel penta-head bolt for locking
(pad-lockable).
• Large 11” x 31” Front Opening.
• Make it a secondary pedestal by ordering
3 lay-in 6 port 350 MCM connectors installed inside.
(MPP-141480-MG-L6350)
• Abundant access inside the pedestal.
MPP-141480-MG-X
• Lightweight, only 35 lbs.
• The corrugated base provides strength against sidewall ground pressures.
• The bottom of the base is flanged to prevent twisting when buried.
• Recommended burial depth 30”.
Large service entrance door (11” x 31”) is
secured with a stainless steel penta-head
bolt fastened to an encased brass nut on
the interior frame. A stainless steel cup
goes around the penta-head bolt for added
security. The cup has a hole in it for
pad-locking.
MPP-141480-MG-L6350
Page 46
07/15
Meter Pedestals, Fiberglass
Features: MP/R-85-MG
• This series is manufactured of compression-molded fiberglass (SMC).
Fire retardant and UV additives are permanently molded in throughout the
laminate.
• 88” tall pedestal will accommodate most surface-type meter mounts and
service entrance equipment.
• 64” above grade allows for easy meter reading.
• Pigment is permanently molded into the fiberglass and the fiberglass does
not peel, providing a maintenance free pedestal for many years.
• The back of the pedestal in removable for convenient cable training.
• Standard color is munsell green.
• Stakes are available for added stability when installed.
• Recessed penta-head locking is an option.
• MP-85 or MPR-85 (does not include meter, enclosure or conduit.)
• MPR-85-MG front side or flat side is the surface area for mounting a
meter to.
MP-85-MG
(Hasp Lock)
MPR-85-MG (Hasp &
Penta-Head Lock)
MP-85-MG
(Hasp Lock)
MPR-85-MG (Hasp &
Penta-Head Lock)
Top
Dimension
Height
Above Ground
Below
Ground
MPP-141480-MG
14” x 14”
80”
50”
30”
Penta-Head Bolt
MPP-141480-MG-L6350
14” x 14”
80”
50”
30”
Penta-Head Bolt
MP-85-MG
8” x 8”
88”
64”
24”
Hasp
MPR-85-MG
8” x 8”
88”
64”
24”
Hasp and Penta-Head
Nordic Meter Pedestal
Locking System
07/15
Page 47
Meter Pedestals, Fiberglass
Features: MP-114-MG
• One-piece meter pedestal with encapsulated green treated plywood.
• Produced of fire-retardant resin and a combination of chopped glass
spray-up and hand lay-up using woven roving glass reinforcement,
which adds greatly to their strength.
ultraviolet attack.
• Standard color is munsell green.
• 114” high x 12 1/2” wide x 6” deep.
• Pedestal will accommodate most surface-type meter mounts and service
entrance equipment.
• The front of the MP-114-MG contains encapsulated green treated plywood which makes it simple to attach screws to fasten the meter
enclosure.
• Cable entrances measure 4” wide x 12” high making it accessible for
training cables in and attaching to the meter.
• MP-114-MG (does not include meter, enclosure or conduit.)
• 72” above grade allows for easy meter reading.
Nordic Meter Pedestal
MP-114-MG
Height
Above Ground
Below
Ground
Locking
System
114”
72”
42”
N/A
MP-114-MG
Front View
Page 48
MP-114-MG
Back View
07/15
Pedestals, Tap
Pedestals, Tap
Features: ND-301830-MG-X-L750350P-X
• This secondary pedestal accommodates up to three connectors with each
connector accommodating one large 750MCM feeder cable, six 350MCM
secondary taps, and two street lighting taps.
• ND-301830-MG-X-L750350P-X has a removable lid for easy access for
hooking up secondary wires to the connectors.
• The 750MCM feeder cable accommodates a wire range of 750MCM maximum
to 1Ø minimum.
• The 350MCM secondary tap accommodates a wire range of 350MCM
maximum to No. 10 wire minimum.
• No part of the connector comes in contact with the shell of the pedestal for
safety.
• The connector provided has a lay in type set screw assembly that provides for
easy cable connection in the field.
• Electrical utilities will be able to use less elbows, less primary cable, and reduce
labor associated with installing elbows onto the primary cable in the transformer.
• Benefits can also be realized by reducing the number of single phase
transformers to provide power to apartment complexes, retirement communities
and other installations of a similar nature.
• The ND-301830-MG-X-L750350P-X does not include the ground sleeve.
Available ground sleeves include:
•
CGS-30-18-18-MG-21x10
•
GS-30-18-24-MG-20x9
•
GS-30-18-30-MG-21x10
Top
Width
Top
Depth
Cabinet
Height
Recommended
Burial Depth
30”
19.5”
31”
GS Required
Tap Pedestal
ND-301830-MG-X-L750350P-X
07/15
Page 49
Pedestals, Tap
hardware.
• Convex base shape and step design resist sidewall
deflection when installed.
• Pedestals accommodate up to 3 or 4 connectors.
• Each fiberglass angle accommodates one heavy duty 10 or 12 port
750MCM connector each with a rubber insulating boot.
• Conductor wire range is 750MCM down to 1/0.
• No part of the connector comes in contact with the shell of the pedestal
for safety.
• Connectors are manufactured from high strength 6061-T6 aluminum
alloy to provide premium electrical and mechanical performance.
• Suitable for use with either copper or aluminum conductors.
• Clear Plated, each covered with a rubber insulating boot
• Rated for 600 Volts, connector meets or exceeds ANSI C119.4 Class A
specifications.
• 3 or 4 fiberglass L-brackets are bolted to a fiberglass U-channel mounted
in the cabinet’s interior for a rigid mounting assembly.
• Connectors are evenly distributed approximately six inches between
each other for room to work safely.
• The ND-362436 Series pedestals can be direct buried or pad mounted.
• The pedestal’s four eyebolts allow the lineperson to simply hook-up the
cabinet, position it over the wires, and place it in the excavated area.
• Rotational lid rotates on pivot bolts creating a lower center of gravity that
reduces the force required to open the pedestal.
ND-362436-MG-3HDB-10750-X
• Save by buying fewer transformers, elbows, primary cable and labor.
Tap Pedestal
Top
Width
Cabinet
Height
Base
Width
Base
Depth
Max. Burial
Depth
ND-362436-MG-3HDB-X-X
36.5”
36.5”
55”
42”
36.5”
36.5”
55”
42”
36.5”
42.5”
59”
46”
36.5”
42.5”
59”
46”
Finish grade
approximately
6” below
locking
systerm.
36.5”
55”
64.5”
51.5”
36.5”
55”
64.5
51.5”
Page 50
ND-362436-MG-4HDB-12750-X
07/15
Pedestals, Tap
Features: ND-403264-MG-4HDB-24750-X
• Convex base shape and step design resist sidewall deflection when
installed.
• Each of the 4 fiberglass arms accommodates one heavy duty 24 port
750MCM connector insulated by a rubber boot.
• Conductor wire range is 750MCM down to 1/0.
• Connectors are manufactured from high strength 6061-T6 aluminum
alloy to provide premium electrical and mechanical performance.
• Suitable for use with either copper or aluminum conductors.
• Clear Plated, each covered with a rubber insulating boot
• Rated for 600 Volts
• Connector meets or exceeds ANSI C119.4 Class A specifications.
• No part of the connector comes in contact with the shell of the pedestal
for safety.
• Adjustable sturdy strut system can be moved vertically for a safe
working position.
• Connector brackets can be moved horizontally to where you want them.
• Fiberglass arms provide high dielectric insulating properties.
• The ND-403264 pedestals can be direct buried or pad-mounted.
• The pedestal’s four eyebolts allow the lineperson to simply hook-up the
cabinet, position it over the wires, and place it in the excavated area.
• Rotational lid rotates on pivot bolts creating a lower center of gravity that
reduces the force required to open the pedestal.
• Save by buying fewer transformers, elbows, primary cable and labor.
• Need more cable bending radius?
• Ask for an 18” (ND-403264-MG-18EXT) or 36” high extension
(ND-403264-MG-36EXT) that can bolt to the bottom of the pedestal.
ND-403264-MG-4HDB-24750-X
Tap Pedestal
Top
Width
Cabinet
Height
Base
Width
Base
Depth
Max.
Burial
Depth
ND-403264-MG-4HDB-24750-X
39.5”
63.5”
64.5”
51.5”
18”
39.5”
63.5”
64.5” 51.5”
18”
ND-403264-MG-18EXT
07/15
Page 51
Page 52
07/15
ORDIC
ORDIC FIBERGLASS,
FIBERGLASS, INC.
INC.
PRODUCT CATALOG
07/15
Page 53

Product Catalog - Nordic Fiberglass, Inc.

Transcription

Similar documents

threeport - Bathcraft

lexington - Bathcraft

armor core

e and Cover - VPC Fiberglass

DELL - Bathcraft

FPVModel RaceGates Setup Manual

kik-step®

Guardian GLHL-SS GLHR-SS

ODK Brochure