ENGINE SERVICE TOOL - force tool of auto repair tool automotive

Transcription

Engine Service Tool
ENGINE SERVICE TOOL
1- 31
Under Car Service Tool
32 - 57
Electrical Service Tool
58 - 66
EN0137
EN0004 Doughnut Stretcher
4PC Diesel Injector Socket Set
Brake Service Tool67-74
Body Service Tool
75 - 83
Battery Service Tool84
Air Conditional Service Tool
85 -87
Cooling System Service Tool88 -97
Diagnostic Service Tool
115 -116
Motorcycle Service Tool
117-148
Truck Service Tool
149 -150
Timing Service Tool
151- 217
General Tool
218 - 238
Gear Puller And Specialty Puller
239 - 245
Lubricating And Oil Filter Tool
246 - 253
Hand Tool
254 - 260
261- 264
Pneumatic Tool265-270
Specialty Socket & Socket Set
Wrench And Spanner Tool
EN0132
Honda & Acura Crankshaft and
Harmonic Balancer Holder
For use on ALFA ROMEO, CHRYSLER, BMW, FORD,VW,
MERCEDES, AUDI, OPEL, VAUXHALL, SEAT, VOLVO,
ROVER also on VOLVO, MAN 2.5TD & SCANIA HGVS.
1PC Injector socket 6PT x 22mm x 110mm(L).
EN0144 Honda Crankshaft Pulley Holder Kit
98 -114
Benz And Bmw Service Tool
Pliers And Plastic Cutter One end features an offset hook.
For easy removal, use to grab onto the rubber mounting
rings or “doughnuts” used in many exhaust systems for easy
removal.
271- 278
278 - 282
Allows the crankshaft pulley and/or harmonic balancer bolt to
be broken loose.
Includes tool necessary to properly counter the rotation of
the crankshaft pulley/harmonic balancer during removal and
reinstallation of crank bolt.
Secures the pulley in place not allowing it to rotate during
removal and reinstallation of crank bolt.
Specially designed to work on 1990 and newer Honda and
Acura models and Honda civic 1980 and newer models.
EN0133
Allows the crank shaft pulley and harmonic balancer bolt to
be broken loose.
Secures the pulley in place not allowing it to rotate during
removal and reinstallation of crank bolt.
Specially designed to work on 1990 and newer Honda and
Acura models.
EN0227 Crank Seal Remover and Installer Kit
Honda And Acura Harmonic Damper
Pulley Holding Tool (50mm)
This unique 50mm tool has been developed to aid in the
removal and installation of the crank bolt on most Honda and
Acura engines.
In operation with the use of a 1/2” breaker bar or ratchet this
tool holds the harmonic damper pulley from rotating when
removing the pulley bolt.
There is a hole in the center of the tool to allow the use of a
socket and extension bar to break loose or tighten the pulley
bolt.
Allows the crank seal to be replaced without dismantling the
crank case saving your time and costs.
Universal use covering a wide range of cars with oil seals
between 27mm and 58mm in diameter.
Use the existing bolt in the vehicle for installation.
Screw type adapter to fit centering.
The blue seal adapters are made of aluminum to prevent the
damage of crank.
EN-1
www.handyforce.com
ENGINE SERVICE TOOL
EN0237 Assembling And Disassembly Of
Self Adjusting Clutches Master Kit
Suitable for most Self Adjusting Clutches SAC (3 and 4 holes)
equipped on vehicles of FIAT GROUP, VW-AUDI, BMW,
MERCEDES, VOLVO, OPEL, RENAULT etc.
Allows operations on clutch equipped with this device in order
to prevent any damage to system and to keep adapter ring in
right position.
Advantages:
Pre-tightening of disk pushing plate during assembly and
disassembly avoiding clutch deformation.
Alignment of clutch disk to drive bearing or to disk pushing
plate.
EN0177
2PCS Lambda Sensor Socket Thread
Chaser
Used for repairing and cleaning damaged threads on lambda
sensor ports.
Size:
1PC 12mm x P 1.25
1PC 18mm x P1.5
EN0259 Universal Clutch Aligning Tool
EN0208 Oil Pan Repair Master Set
Feature: Solid and fast solution for the repair of defective oil
drain screw thread without the expensive replacement of the
sump.
Application: The damaged thread is simply to tap away to the
next size expands. Oil drain screw in part with Allen drive for
oil pans with recessed drain opening suitable.
Universal applications e.g. for: Audi, BMW, Citroen, DaimlerBenz, Ford, Fiat, Honda, Mazda, Mitsubishi, Nissan, Opel,
Peugeot, Porsche, Renault, Saab, Seat, Skoda, Toyota, Volvo,
VW etc.
Scope of supply: complete with 1 / 3 foam insert in the plastic
case. Replacement oil drain screw and aluminum seals are
available.
Consisting of:
1 PC Special Taps M13x1.5
5 PCS Oil drain plug gasket with aluminum M13x1.5 external
drive 6-kant SW17
5 PCS Oil drain plug gasket with aluminum M15x1.5 external
drive 6-kant SW19
5 PCS Oil drain plug gasket with aluminum M17x1.5 inner
drive 6-kant SW 8
5 PCS Oil drain plug gasket with aluminum M20x1.5 inner
drive 6-kant SW 10
EN0228 Universal Valve Spring Compressor
Tool
Suitable for replacement of valve springs and valve stem oil
seals without the need to remove the cylinder head.
Application: Opel / BMW / Seat / VW / Audi / Hyundai / Toyota /
Ford / Renault 19 and Clio.
EN0231 Damper Pulley Holder Wrench Set
EN0234 Engine Calibration and Set up Kit
Directions
The sliding indicator to display the piston movement.
Use on the Hemi-type engines, easily find the TDC
compression stroke.
Set included 12mm and 18mm spark plug adapters.
EN0171
Contents:
1 PC 13 mm box style pulley holder wrench.
Valve Spring Compressor Repair Kit
Completes service tool kit for OHV & OHC petrol or diesel
engines.
Use on AUDI, NISSAN, TOYOTA, CHRYSLER, HONDA,
MAZDA, MITSUBISHI, PORSCHE, VOLVO, VW.
EN0245 9PCS Pre-Heater Plug Puller Set
EN0243 13 PCS Alternator Freewheel Pulley
Removal Tool
EN0220 Fuel Line Connectors Pliers
Special design aligns and assembles clutch on the
workbench for easy installation.
Suited for front wheel drivers that have no pilot bearing in
flywheel.
Designed for most vehicles up to 5 tons with single plate
clutches.
www.handyforce.com
Use for VW-AUDI, FIAT, GM, OPEL MERCEDES…etc, E.G.
MERCEDES M-CLASS with petrol engines.
For removal and replacement of the connections on the in-line
fuel filter.
Required when replacing the fuel filter or during engine repairs.
EN-2
2 PCS Reamer to ream out and clean the bore between the
glow plug and combustion chambers. Suitable for Mercedes
CDI engines 4,5&6 cylinder, OM611, 612, 613 with glow
plug threads M10 x 1.0 and 4valve engines OM604, Om605,
OM606 with glow plug thread size M12x1.25.
1 PC puller for pulling out pre-heater plugs with 10mm across
flats on Mercedes CDU engines.
6 PCS 3/8” Dr. Universal joint glow plug socket
Size: 8,9,10,12,14,16mm, length 160mm Material: CR-V.
Contents:
H10, H8, T50, T40, M10, M8, M10 Spline x 1/2” Dr for Bosch
Alternators with freewheel pulleys.
1/2”Dr. to hex adapter,
T50 star x 1/2” Dr.
2 PCS Pulley connectors.
2 PCS Further adapters.
EN-3
www.handyforce.com
ENGINE SERVICE TOOL
EN0135 Camshaft Drive Belt Pulley Puller
EN0242 Hydraulic Valve Lifter Puller
Special puller designed for pulling camshaft pulley wheels on 4
& 6 cylinder, V6 & V8 engines on VW and AUDI petrol engine.
EN0244 Clutch Centering Mandrels
EN0107
EN0112
PSA Exhaust Pipe Clamp Pliers
Special design to hold opening the spring clamp and replace
the exhaust.
Total length: 300mm.
Maximum jaws opening: 60mm.
Large pump remover & sprocket retaining tools for injection
pump removal on BMW models with M74/M47TU and M57/
M57TU2 2.0 & 3.0 diesel engines.
Small pump remover & sprocket retaining tool for injection
pump removal on Land Rover Freelander and Rover 75
models with TD4 and M47 2.0 engines.
EN0110
VW, AUDI Belt Pulley Holder
Diesel Injector Puller
Assists removal of stubborn BOSCH and LUCAS diesel
injectors-saves time and money when injectors are difficult to
remove.
With M8, M12, M14 adaptors.
EN0115
4PCS Sensor & Sending Unit
Socket Extension Set
EN0260 Diesel Injector Puller Set
Special design to hold the belt pulley on VW, AUDI.
Applicable:
VW: LUPO, POLO Classic, GOLF, BORA & CADDY.
AUDI: A2
For fast and exact clutch plate centering on vehicles with
clutch guide bearing.
For passenger cars and small
commercial vehicles.
Ø 20mm ~ 26.6mm
Ø15mm ~ 19mm
EN0113
EN0111
Suitable for the removal of stubborn Bosch / Delphi diesel
injectors.
Set included 6 adaptors for different removal methods.
Features a flexible joint adaptor allowing the slide hammer to
be used in restricted areas.
Ribbed Drive Pulleys Puller
EN0130 Oil Pump Primers
VW Belt Pulley Holder
10PC Sensor & Sending Unit
EN0184 Socket Master Set
Special design to hold the belt pulley on VW.
Applicable:
VW LUPO, POLO Classic, BEETLE, GOLF, BORA & CADDY.
SEAT IBIZA CORDOBA.
EN0233 Fuel Filter Key
Universal design for clamps onto any ribbed pulley.
This tool can use for crankshafts, alternators, air conditioning
units, and water pumps.
EN0114
Set includes:
1PC 22mm special tube socket.
1PC oxygen sensor thread chaser.
1PC oxygen sensor wrenches offset (2-1/8") & super duty 12
& 6 point socket.
1PC oxygen sensor socket.
Oxygen Sensor Rethread Tool
Cleans threads in oxygen sensor holes.
Use with 3/4” hex socket or 3/8” square drive.
M18X1.5 also works on m18x1.5 spark plug threads.
www.handyforce.com
These tools are designed to prime the lubricating system of a
rebuilt engine prior to its first start to prevent the damage of a
dry start.
It works by connecting to the oil pump shaft through the
distributor hole designed to be used with a 3/8” reversible drill.
GM V6 and V8 oil pump primer.
Oil pump primer for Fords with 1/4” hexes.
Oil pump primer for Fords with 5/16” hexes.
EN-4
Fuel filter key Ø108.
Suitable for Peugeot, Citroen, Renault e.g. with HDI diesel
engines.
The fuel filter key is required to remove and install the fuel filter
cap when replacing the fuel filter cartridge.
Drive: 3/8”
Dimension: Ø 108 mm.
Suitable for most of vehicle of oxygen sensor and sending unit
remover and install.
1PC 22mm special tube socket.
1PC oxygen sensor wrenches offset (2-1/8") & super duty 12
& 6 point socket.
1PC oxygen sensor socket.
1PC 1/2" drive x 29 x 90 mm oxygen sensor socket.
1PC 3/8" drive x 7/8" x 90mm oxygen sensor socket.
1PC 1/2" drive x 27 x 85mm injector socket.
1PC 3/8" drive x 7/8" x 80mm vacuum switch socket.
1PC 3/8" drive x 1-1/6" x74mm oil sender unit socket.
1PC 3/8" drive x 7/8" x 50mm heated oxygen sensor socket.
1PC 3/8" x 7/8" x 30mm offset oxygen sensor wrench.
EN-5
www.handyforce.com
ENGINE SERVICE TOOL
EN0118
EN0065 Exhaust And Tailpipe Cutter
Cam and Crank Shaft Seal Puller
Engage the adjustable hook behind the seal.
Brace the push rod against the engine head then push the
handle to remove the seal.
Remove the seal easily & quickly without damage to the cam
& crank shaft.
EN0119
Fifteen blades effectively cut pipe so only 1/4” turn is needed
for a complete cut.
Use tool to cut pipes 3/4" to 3"(19 to 76mm) in diameter.
Not for use on stainless steel pipe.
EN0182 Diesel Injection Pump Puller
3PCS Fuel Line Disconnect Set
EN0172
EN0183 8PCS Sensor Socket Set
Fuel Line Pliers
For VOLKSWAGEN, AUDI, SEAT, SKODA Vehicle.
For use on three ended hose clips which are fitted to, AUDI/
SEAT/SKODA/VOLKSWAGEN fuel lines clamps.
Clamping range 28-18mm.
EN0180 6PCS Diesel Injector Socket Kit
22mm special tube socket.
Oxygen sensor thread chaser.
Oxygen sensor wrenches offset (2-1/8") & super duty 12 & 6
point socket.
Oxygen sensor socket.
1/2" drive x 29 x 90 mm oxygen sensor socket.
3/8" drive x 7/8" x 90mm oxygen sensor socket.
3/8" drive x 7/8" x 50mm heated oxygen sensor socket.
3/8" x 7/8" x 30mm offset oxygen sensor wrench.
EN0117
Design for uncoupling quick release fittings on fuel line to most
of the cars.
1/4”, 5/16” (Ø8mm) Ford-Mercury, Doge-Chrysler, Renault.
3/8” (10mm) Ford-Mercury, Doge-Chrysler, Renault.
GM Chevrolet, Buick-Pontiac, Renault, Fiat, Ford, Opel.
Suitable for BMW, LAND ROVER, VAUXHALL, OPEL 2.5 TDS
engines diesel injection pump.
EN0167
Water Pump Holding Tool
This socket set can use for Alfa Romeo, Audi, Chrysler, Ford,
Land Rover, Mercedes-Benz, Peugeot, Rover, Seat, Vauxhall
and Volvo of diesel injector install and removal.
EN0181
1PC M16 x 1.25 x 70mm(L) tap reamer.
5PCS M14 x 1.25(11.2) replacement thread sleeve.
Oxygen Sensor Socket
EN0120 Universal Pulley Holder & Fan
Clutch Set
EN0189 Diesel Injection Pump Puller (BMW)
This set is designed to removes and installs fan clutch & hold
the camshaft pulley.
Use for most of the cars.
Contents with different tap to fit any cars and pin width can
adjust.
Can adjust different width from 40mm to 220mm.
Size available:
2PCS Ø6mm-Ø10mm
2PCS Ø8mm-Ø11mm
2PCS Ø10mm-Ø12mm
2PCS Ø11mm-Ø16mm
www.handyforce.com
16PCS Spark Plug Thread Repair
Tool Set
For OPEL ECOTECH engine.
Simply remove access plate from front cover and install the
tool to holding timing chain in place.
Use for 2002-2008 GM 2.2L & 2.4L ECOTECH engine in
CHEVROLET OLDSMOBILE, OPEL/VAUXHALL PONTIAC
and SATURN PLATFORMS.
Application:
GM ECOTECH 2.2 engine code F, 2002-2005 CHEV
CAVALIER, 2005-2008 CHEV COBALT, 2003-2008 CHEV
MALIBU, 2002-2004 OLDS ALERO, 2002-2005 PONTIAC
SUNFIRE, 2007-2008 PONTIAC G5, 2002-2005 PONTIAC
GRAND AM, 2002-2006 SATURN VUE, 2003-2007 SATURN
LON, 2000-2005 SATURN L SERIES, 2.4 ENGINE CODE B,
2005-2008 CHEV COBALT, 2005-2007 CHEV HHR, 20042008 CHEV MALIBU, 2006-2008 PONTIAC G6, 2006-2007
PONTIAC PURSUIT, 2006-2008 PONTIAC SOLSTICE, 20072008 SATURN AURA, 2006-2007 SATURN LON, 20072008 SATURN SKY 2.2 ENGINE 16V, ASTRA-G, ZAFIRA-A,
VECTRA-B/C, SIGNUM and VX220.
EN-6
Applicable:
FORD, TOYOTA, NISSAN, BENZ, BMW and most of
European cars, also GM vehicles.
Flare nut for vacuum switch & oxygen sensor service on the
computer-controlled engines.
Features:
3/8” of the double square DR. 7/8” (22mm) 12 points & 22mm
6 point.
EN0198 Engine Oil Dipstick For Audi
Engine oil dipstick applicable to 2009 Audi A4, A5 and A6 with
engines 2.0L TFSI, 3.2L FSI and 4.2L FSI.
This tool is specifically designed for holding the sprocket/chain
in place when disassembling the VP44 injection pump and high
pressure pump.
Common rail fitted to BMW engines:
318D/COMPACT(E46)
320D/TD COMPACT(46)
330D(E46)
525D(E39)
525D(E60/E61)
530D(E39)
530D(E60/E61)
535D(E60/E61)
730D(E38)
X5 3.0D(E53)
EN-7
www.handyforce.com
ENGINE SERVICE TOOL
Cam Seal Installer(FOR MAZDA,
EN0185 NISSAN, TOYOTA/LEXUS)
EN0187
This tool is designed to install the cam seals in 4&6 cylinder
engines for MAZDA, NISSAN & TOYOTA/LEXUS engines that
have 10&12mm*1.25 cam bolts.
These engines are mounted transversely which puts the
camshaft end in very close proximity to the shock tower
making replacement of the cam seal extremely difficult using
conventional methods.
Screw the threaded rod into the cam end, slide the body over
the rod against the seal and press in the seal using the nut
provided.
Slide Hammer Type Injector Nozzle
EN0186 Puller
Can use for Mercedes CDI engines OM 611, 612, 613,…etc.
Injection nozzles that do not fit very tightly can be pulled out
without needing to take them apart or remove the cylinder
block.
The specialty design , the puller is additionally supported by
the steel ball on the valve cover, which prevents the puller from
tipping during the removal process.
EN0188 Glow Plug Remover Tool
This unique tool has been developed to aid in the removal
and installation of the crank bolt on most HONDA and ACURA
engines.
It has been re-engineered to work on 2004 and later new style
SUV'S with a 50mm damper pulley as well as all previous
models serviced.
In operation with the use of a 1/2" breaker bar or ratchet this
tool holds the harmonic damper pulley from rotating when
removing and setting the final torque specification on the
pulley bolt.
There is a hole in the center of the tool to allow the use of a
socket and extension to break loose or tighten the pulley bolt.
Application:
For HONDA
ACCORD 2.2L 4 CYLINDER 90-97, 2.7L V-6 96-97, 2.3L 4
CYLINDER 98-02, 2.4L 4 CYLINDER 03 & LATER, 3.0L V-6
98 & LATER.
CIVIC 1.6L 4 CYLINDER 92-00, 1.7L 4 CYLINDER 01 &
LATER, 2.0L 4 CYLINDER 03 & LATER.
CRV 2.0L 4 CYLINDER 97-01, 2.4L 4 CYLINDER 02 &
LATER.
DEL SOL 1.6L 4 CYLINDER 93-97.
INSIGHT 1.0L 3 CYLINDER 00 & LATER.
ODYSEY 2.2L 4 CYLINDER 95-97, 2.3L 4 CYLINDER 98, 3.5L
V-6 99 & LATER.
PILOT 3.5L V-6 03 & LATER.
PRELUDE 2.2L 4 CYLINDER 92-01, 2.3L 4 CYLINDER 92-96.
S2000 2.0L 4 CYLINDER 00-03, 2.2L 4 CYLINDER 04 &
LATER.
ELEMENT 2.4L 4 CYLINDER 03 & LATER.
RIDGELINE 3.5L V-6 06 & LATER.
For ACURA
CL 2.2L 4 CYLINDER 97, 3.0L V-6 97-99, 2.3L 4 CYLINDER
98-99, 3.2L V-6 00-03 INTEGRA 1.6L 4 CYLINDER 90-92, 1.7L
4 CYINDER 92-93, 1.8L 4 CYLINDER 93-01.
LEGEND 3.2L V-6 91-95.
MDX 3.5L V-6 01 & LATER.
RL 3.5L V-6 96 & LATER.
RSX 2.0L 4 CYLINDER 02 & LATER.
TL 3.2L V-6 95 & LATER.
TSX 2.4L 4 CYLINDER 04 & LATER.
RDX 2.3L 4 CYL TURBO 06 & LATER.
The 10mm split nut will work on ford 6.9L and 7.3L diesels,
GM 5.7L, 6.2L, and 6.5L diesels; and various diesels in import
vehicles.
Plus many agricultural and construction diesel applications.
www.handyforce.com
4" Offset Harmonic Damper Pulley
Holding Tool (HONDA & ACURA)
EN-8
EN0190
EN0193 7PCS Injector Puller
Diesel Injection Pump Puller
(LAND ROVER)
This tool is specifically designed for holding the sprocket/chain
in place when disassembling the VP44 injection pump and
high pressure pump.
Common rail fitted to LAND ROVER engines:
LAND ROVER, FREELANDER(TD4), ROVER 75(M47).
EN0191
Injector Puller
For Bosch injector system of Mercedes Benz.
For removing adapted tight common rail injectors without
having to disassemble cylinder head.
Use for Mercedes-Benz CDI engines 611.612.613,etc.
Injection puller with impact hammer, injection nozzles that do
not fit very tightly can be pulled out without needing to take
them apart or remove the cylinder block.
EN0194 Universal Camshaft Sprocket Puller
For Bosch injector system of Mercedes Benz.
Use for Mercedes-Benz CDI engines 611.612.613,etc.
Injection puller with impact hammer, injection nozzles, that do
6PCS Injector Puller(For BOSCH
EN0192 Injector System of MERCEDES-BENZ)
Hold the sprocket and undo the retaining bolt or nut and
remove.
This tool enables the removal of the camshaft sprocket on a
wide range of vehicles.
Suitable size from 45mm to 70mm.
EN0195 Diesel Injector Seat Cutter Set
Use for MERCEDES-BENZ CDI engines 611.612.613,….etc.
This kit has been specially designed for the clean and recutting of injector seats on modern common rail diesel
engines.
The kit includes 4 seat cutting reamers for Bosch, Delphi and
universal application along with a special angled reamer for
IVECO/FIAT applications.
EN-9
www.handyforce.com
ENGINE SERVICE TOOL
EN0197
Diesel Injector Nozzle Socket
The set include 4pcs diesel injector nozzle socket.
1/2” DR socket can use for SIEMENS & BOSCH injectors.
Suitable for Peugeot and Citroen with 2.0 engines (110/135hp)
HDI engines.
Copper Washer Removal Tool For
EN0199 Diesel Injector
engines.
Material: high carbon steel SKD-11.
EN0225 2PCS Rubber Ring Hook Tool Set
EN0226 6” Tail Pipe Cutter
Special designed to pull the rubber ring which connected with
exhaust tube.
Two special angle hook attached.
EN0206 Mechanic’s Stethoscope
Ratcheting Serpentine Belt
EN0221 Wrench Set
Lubricate cutting wheels with light machine oil prior to use and
before storage.
Turn cutter handle counterclockwise to extend shaft as needed
to fit pipe diameter.
Wrap chain around pipe and hook link into tabs on cutter
handle.
Turn cutter handle as needed to ensure chain fits snugly
around pipe. do not over tighten.
Slowly rotate cutter around pipe.
As cutting progresses, turn cutter handle slightly to maintain
snug pressure.
Take multiple shallow cuts for best results.
Use for 3-1/2” to 6” tail pipe.
EN0249 Water Pump Removal Tool Kit
Provides a fast and easy way to locate noise in engine or
bearing and other moving parts.
High quality surgical PVC and rubber parts for increased sound
definition.
Aluminum alloy probe / needle for finding the exact location of
specific noises.
Service approximately 90% of all vehicles equipped with
spring-loaded serpentine belt tensioners.
Ratcheting action allows quickly and easy positioning of
wrench driving end for tensioner access from any angle.
For use when servicing serpentine drive belts or any beltdriven accessories.
Specifically designed to fit into tight areas.
Size:
Inner hole: 7mm.
Length: 230mm.
Collet type easy to holding the copper washer.
EN0222 Exhaust Pipe Hanger Stretcher
EN0200 Fuel Pump Wrench
Use for VOLKSWAGEN T5 & TOUAREG 2.5D water pump
removal.
Application for engine code, BAC, BLK, BPD, BPE.
EN0205 Mechanic’s Stethoscope
Wrench for removal and installation of the fuel pump on Audi
90 Quattro.
EN0320 Adjustable Piston Ring Installer
EN0239 Valve Shim Remover
Stretcher removes exhaust systems for rubber-style hangers
easily.
The slip-resistant handles and self-locking force pin allow for
quick removal of rubber exhaust hangers.
A slim profile and 25° offset allow for easy access to confined
areas.
www.handyforce.com
Provides a fast and easy way to locate noise in engine or
bearing and other moving parts.
High quality surgical PVC and rubber parts for increased
sound definition.
Aluminum alloy probe / needle for finding the exact location of
specific noises.
Supplied with a rubber trumpet for checking vacuum and
pressure flow.
EN-10
For use on Opel, Volvo and some European Cars with
overhead camshafts which use spacer shim.
Fits piston range from 3/64” to 1/4” thick.
Makes installing piston rings safe and easy without over
expanding rings.
Works on most common piston rings.
Adjustable spread stop for fast bread free installation and
removal.
EN-11
www.handyforce.com
ENGINE SERVICE TOOL
Diesel Injectors Seat Cuter and
EN0230 Face Cleaner
engines.
The kit includes 4 seat cutting reamers for BOSCH, DELPHI
and universal application along with a special angled reamer
for IVECO/FIAT applications.
EN0247
Impact Diesel Injector Remover VAG
Installs pistons from 2-7/8” to 4-3/8” (73mm to 111mm).
Ratcheting lock allows for bands to compress in small
increments.
Can be used parallel vertically perpendicular horizontally.
Set includes pliers and six bands.
Contents:
EN0247-1 ratchet pliers.
EN0247-6 band size 2-7/8” to 3-1/8”.
EN0247-7 band size 3-1/8” to 3-3/8”.
EN0247-8 band size 3-3/8” to 3-5/8”.
EN0247-9 band size 3-5/8” to 3-7/8”.
EN0247-10 band size 3-7/8” to 4-1/8”.
EN0247-11 band size 4-1/8” to 4-3/8”.
EN0247-18 band size 4-3/8” to 4-5/8”.
A unique tool for repair damaged spark plugs, glow plugs and
Lambda probe threads.
Features:
Quick and easy repair without extensive component
disassembly.
Easy to use and proper fixed with absolute gas-tight seating of
the inserts.
Thin wall bushings with rust protective coating.
Repair easily without complex component.
Contents:
1 PC Thread cutting tap M18 x 1.5 L=50mm
1 PC Piloted reamer M18 x 1.5 L=50mm
1 PC Screw in tool for insert nut L=90mm M18 x 1.5
1 PC Screw sleeve 27H x 81mm
5 PCS Insert nut with collar, L=9mm IG=M18 x 1.5/AG=M20 x
1.5
EN-12
EN0218 21 PCS Spark Plug Thread Set
M14X1.25
5kg slide hammer with threaded adaptors for removing seized
fuel injectors from VAG TDI engines.
The kit includes direct, offset and hook adaptors.
EN0216 22 PCS Glow Plug Thread & Spark
Plug Set M12X1.25
EN0219 10 PCS Oxygen Sensor Thread Set
M18X1.5
Piston Ring Compressor Set
www.handyforce.com
After removing used injector from cylinder head is important to
clean seat of injector, by this tool you can clean seat as well as
injector seat.
All process is made manually by turning by hand with apply
little bit of pressure.
EN0241
Features:
disassembly.
the inserts.
Contents:
1 PC Piloted tap M12 x 1.25
1 PC Piloted reamer M12 x 1.25
1 PC Screw in tool for insert nut, L=100mm M12 x 1.25
5 PCS Insert nut with collar, L=12mm IG=M12 x 1.25/AG=M14
x 1.25
x 1.25
x 1.25
Features:
disassembly.
the inserts.
Contents:
5 PCS Insert nut with collar, L=11.2mm IG=M14 x 1.25/
AG=M16 x 1.25
AG=M16 x 1.25
AG=M16 x 1.25 cone
EN0204 Oscillating Valve Lapper
Laps valves in double quick time.
Gas tight seal in seconds.
Unique patented mechanism converts rotary drill action to
oscillating grinding motion.
22/28mm sucker heads fits most valve sizes.
Fit all power drills with 5/16"(8mm) chuck.
Essential on multi-valve engines.
EN-13
www.handyforce.com
ENGINE SERVICE TOOL
EN0214 16 PCS Glow Plug Thread Set
M10X1.0
EN0215 10 PCS Glow Plug Thread Set
M10X1.25
Features:
disassembly.
the inserts.
Contents:
5 PCS Insert nut with collar, L=12mm IG=M10x1.0/
AG=M12x1.0
5 PCS Insert nut with collar, L=19mm IG=M10x1.0/
AG=M12x1.0
1 PC Screw in tool for insert nut L=103mm M10x1.0
Features:
disassembly.
the inserts.
Contents:
EN0203 Korean Vehicle Diesel Injector
Puller Set
EN0212
Special design used for remove diesel injectors of most Korean
vehicles.
Application:
Hyundai:STAREX, LAVITA, MARTIX, TRAJET, TERRACAN,
SANTA FE, LIBERO, AVANTE XD, GRANDEUR XG, GETZ,
TUESON, NF SONATA, 06’ ACCENT.
KIA:
CARNIVAL, RIO, CARENS, CERATO, OPTIMA,
PICANTO, SORENTO, SPORTAGE,GRAND CARNIVAL.
Crankshaft Sealing Flange
EN0248 Removing & Installing Tool
1 PC Screw in tool for insert nut, L=100mm M10 x 1.25
10 PCS Glow Plug Thread Set
M8 x 1.0
Features:
disassembly.
the inserts.
Contents:
5 PCS Insert nut with collar ,L=11mm, IG=M8 x 1.0 / AG=M10
x 1.0
4PCS Diesel Injector Removal Set
EN0240 For DELPHI/BOSCH
x 1.25
EN0217 10 PCS Oxygen Sensor Thread Set M12X1.5
A unique tool for repair damaged spark plugs, glow plugs and Lambda
probe threads.
Features:
Applicable:16V,1.4,1.6 engine of VW,AUDI,SKODA,SEAT.
Special design tool to replacement crankshaft sealing flange.
EN0246 Fuel Feed Pipe Pliers
Quick and easy repair without extensive component disassembly.
Easy to use and proper fixed with absolute gas-tight seating of the inserts.
Contents:
5 PCS Insert nut with collar, L=9mm IG=M12 x 1.5/AG=M14 x 1.5
www.handyforce.com
EN-14
For undoing quick release connections on fuel feed pipe lines.
Suitable for OPEL/VAUXHALL, FIAT, GM, VW….etc.
Adaptors can also be used with an air tool to loosen the
injectors by vibration.
Set of 3 adaptors plus a special tool for removing the internal
part of BOSCH injectors.
Specifically designed for removing DELPHI/BOSCH diesel
injectors using a slide hammer with 5/8” UNF thread.
EN-15
www.handyforce.com
ENGINE SERVICE TOOL
EN0213
EN0236 Valve Stem Seal Tool Set
10 PCS Glow Plug Thread Set
M9 x 1.0
Features:
disassembly.
the inserts.
Contents:
5 PCS Insert nut with collar, L=11mm IG=M9 x 1.0 /
AG=M11x1.0
For Valve Stem Sealing Rings.
This tool set allows the removal and replacement of valve shaft
sealing rings.
Consists of:
Basic Slide Hammer
Valve Seal Collect Chuck (bucket-tappets diam. 26 mm
upwards)
Valve Seal Collect Chuck (bucket-tappets diam. 23 mm up to
26 mm)
Oil Seal Removal Pliers - Long
Press Set for valve seals (10 pcs., Ø 9.5 - 14 mm inside)
EN0310 Piston Ring Service Tool Set
EN0229 8PCS Diesel Injector Seat Cutter Set
EN0303
14 PCS Oxygen Sensor Special
Socket Set
6 PCS Opening Single Ended
EN0304 Ratchet Wrench
Contents:
●17x78mmL(12PT):REUAULT.
●19x78mmL(12PT):VW POLO, AUDI, SEAT, MAZDA.
●20x78mmL(6PT):ABIERTU JAPAN.
●27x78mmL(6PT):ABIERTU JAPAN.
● 2 1 x 9 0 m m L ( 1 2 P T ) : S E AT, A U D I , V W, S K O D A , A L FA ,
ROMEO,MITSUBISHI.
●22x78mmL(12PT):SEAT, AUDI,VW, SKODA,OPEL.
● 2 2 x 11 0 m m L ( 1 2 P T ) : M E R C E D E S , C I T R O E N ,
PEUGEOT,FORD, NISSAN. MAZDA, MITSUBISHI, SEAT,
AUDI,VW, ETC.
●27x78mmL(12PT):SEAT, AUDI, VW, SKODA, BMW,
●MERCEDES, OPEL FORD, NISSAN, MITSUBISHI, LIN
COLN(USA).
●27x110mmL(12PT):CITROEN, PEUGEOT, SISTEN LVCAS.
●28x78mmL(12PT):ALFA ROMEO, FIAT, ROVER, OPEL.
●30x78mmL(12PT):MERCEDES.
●22x150mmL(12PT).
●7/8" OFFSET OXYGEN SENSOR SOCKET.
●7/8" OFFSET DEEP OXYGEN SENSOR SOCKET.
●29x90mmL (6PT)
●22x80mmL (6PT)
●22x90mmL (6PT)
●1" & 1-1/16" x 74mmL
EN0308 110mm-160mm Piston Ring Pliers
Can be used on pneumatic & hydraulic connections such as
brake pipes.
Size: 10mm, 11mm, 13mm, 17mm, 19mm, 22mm
EN0309 Valve Spring Compressor
Compressor easily and removes valve springs on most cars
and light trucks,
Work with cylinder head on or off the engine..
EN0306 50mm – 100mm Piston ring Pliers
Tools are used for cleaning place under injection washer after
replacing injector.
It is necessary to clean place under and above washer for
perfect fit new or replaced diesel injector.
Do not use with air tools.
www.handyforce.com
Contents:
Piston ring compressor with ratchet key:
1 PC Height: 3”, capacity 53-125mm.
1 PC Height: 3-1/2”, capacity 90-175mm.
1 PC Height: 4”, capacity 90-175mm.
Piston ring tool capacity: 50-100mm.
Piston ring groove cleaning fits: 2”-5” (51-127mm).
Cleaning blade 1 size: 1/16” to 3/16”.
Cleaning blade 2 size: 2.0mm to 4.5mm,1/4”
Cleaning blade 3 size: 1.2mm to 5.5mm
Offset driver: Phillips and slotted.
EN-16
For removing and mounting piston rings.
Capacity: 110mm-160mm
Finish: Nickel plated.
EN-17
www.handyforce.com
ENGINE SERVICE TOOL
EN0307 80mm-120mm Piston Ring Pliers
EN0321 Cylinder Base Surface Rectifier
EN0311
Piston Ring Compressor
-EN0317
EN0322 Stud Remover and Installer Set
Material: Special spring steel (SK) with heat treaded.
Ratchet type complete with spanner.
Tool with safety adjusting screws.
Size range:
Height
3”
3-1/2”
3”
3-1/2”
4”
6”
6-1/2”
Replaceable Oil Pan Separator and
EN0324 Clean Kit
Straight edge works for precision check the cylinder head or
flat damage or not.
Size:
Length: 600mm.
Width: 50mm.
Hight: 7mm.
Item No.
EN0311
EN0312
EN0313
EN0314
EN0315
EN0316
EN0317
EN0323 114PCS Oil Drain Repair Kit
Capacity (mm)
53-125
53-125
90-175
90-175
90-175
90-175
90-175
Easily remove and install studs without damaging the thread.
Size:
M6 x 1.0
M8 x 1.25
M10 x 1.25
M10 x 1.5
Breaks gasket seals on engine sumps, transmissions or any
difficult to separate gasket joints.
The copper blade could avoid damage on gasket or oil pan
connection joint surface.
Clean up wheel tool helps use to clean all small space on
cylinder head.
Contents:
1PC Replaceable separator steel plate.
1PC Replaceable copper plate.
1PC 2.5mm alley key.
1PC Clean cup wheel adapter.
15PCS Clean cup brush wheel.
Contents:
1PC M13 x 1.25P re-thread tap.
6PCS M13 x 1.25P drain bolt.
72PCS copper washer.
EN0325 5PCS Glow Plug Socket
EN0328 Clutch Alignment Rectifier
EN0327 Camshaft Seal Installer
EN0143 Cylinder Base Surface Rectifier
Straight edge works for precision check the cylinder head or
flat damage or not.
Size:
Length: 600mm.
Width: 36mm.
Hight: 16mm.
www.handyforce.com
Special tool for easily and quickly install camshaft seal in 4 and
6 cylinder.
Material of main body: S45C.
Material of spindle: S45C.
Material of hex nut: S45C.
Spindle sizes: 1/2”-20 x M10 and 1/2”-20 x M12.
Applicable: MAZDA, NISSAN, TOYOTA, LEXUS….etc.
EN-18
Align single disc clutches on most of vehicles, light truck and
tractors.
Properly aligns clutch plate by tapered cone fitting into pilot
bushing or bearing.
8PCS collects ranging from 0.465” (11mm) to 0.980” (24.9mm).
Design for glow plug remover and install.
Use with 1/4” Dr. wrench.
Size and applicable:
8mm for Peugeot, Renault, Citroen, Ford and Mercedes-Benz.
9mm for Opel, FIAT, LANCIA, Alfa, SEAT and VW/AUDI.
10mm for Mercedes-Benz, Peugeot, SEAT, AUDI and VW.
12mm for Peugeot, Renault, Citroen, BMW and OPEL.
14mm Universal type.
EN-19
www.handyforce.com
ENGINE SERVICE TOOL
EN0326 Spark Plug Thread Repair Kit
EN0320 Adjustable Piston Ring Installer
Fits piston range from 3/64” to 1/4” thick.
Makes installing piston rings safe and easy without over
expanding rings.
Works on most common piston rings.
Adjustable spread stop for fast bread free installation and
removal.
This tool kit is designed for repairing stripped or
damaged threads on spark plug seat.
Contents:
1PC Tap M14 x 1.25P.
1PC Step-tap M14 x 1.25P, M15.8 x 1.25P.
1PC Wrench (inside diameter 3/8”).
1PC 3/8” Dr. T-bar.
1PC Insert driver (inside diameter 3/8”).
1PC Seat cutter.
10PCS Copper thread sleeve length 15mm.
10PCS Copper thread sleeve length 9.4mm.
1PC Alley key 2.5mm.
Valve Adjusting Tool
EN0005 (For TOYOTA)
EN0149 Pulley Removing Wrench
For Toyota and other overhead camshaft engines using space
shims.
Shim pliers push between the shim and camshaft allowing the
included
wedge tool to be placed between the valve lifter ledge and
camshaft for
easy shim replacement.
Ideal for removing and assembling any type of grooved pulley
for V-type belt.
This tool keeps the grooved pulley firmly locked.
Enable to tighten or to un-tighten without any difficulty pulley
locking screw.
Has more functions than a standard strap or chain wrench and
will not
damage the components.
Idea for alternator and water pump pulleys, but also essential
for electric
Motors of compressors, washing machines, tool machines etc.
Also suitable to rotate the camshaft when timing the engine
and to remove oil
and gasoline filters.
www.handyforce.com
EN0342 Serpentine Belt Tool
Releases tension on serpentine belts with spring loaded idler
pulley.
This tool is used to remove and install belts on serpentine belt
systems using the spring loaded idler pulley.
Fits idler pulleys requiring 13mm, 15mm, 16mm, 18mm, or
3/8"
square drive socket size, which are on most all domestic
applications.
EN0346 Pin Spanner Wrench
Universal design fits many different types of pulleys having
slots or holes.
Tool also fits camshaft pulleys and crankshaft pulleys.
Adjustable wrench from 1-1/4” to 5”. Wrench work with a 1/2”
Dr. ratchet or
breaker bar.
Pin Size: 3.5mm, 4mm, 4.5mm, 5mm, 6mm, 7mm, 10mm.
For large engines and diesel engines.
Unique direct action compressor lever gives improved visibility
and ease of use in areas of difficult access.
Collet release adapters.
Restricted access adapter 25mm and 30mm.
Jaw opening Min.: 35mm.
Jaw opening Max.: 200mm.
Clearance: 250mm.
Capacity 55-175mm, throat clearance 165mm designed for
use on multi - valve petrol and diesel engines with deep seated
valves.
Collet release adapters.
Restricted access adapter 25mm and 30mm.
Suitable for general use on a wide range of OHC, OHV, and
CVH engines. Universal model with unique dual cam-action,
parallel lift and automatic locking.
Reversible jaw and adaptor.
EN0136 Universal Belt Tension Gauge
EN0348 Spark Plug Hole Thread Chaser
EN0015 Oxygen Sensor Thread Chaser
Cleans threads in oxygen sensor holes.
Use with 3/4" hex socket or 3/8" square drive. Size: M18x1.5
Also works on
M18x1.5 spark plug threads.
EN-20
Tapered double ended for both 14mm and 18mm threads
designed to start
and remove carbon and dirt or straighten damaged threads in
spark plug
hole.
M14 x 1.25 / M18 x 1.5 ,
Hexagon : 21mm
Material: S45C with heat treatment
This tensioning gauge can be used to adjust the tension on the
cam belts
where the movement of the timing belt is measured by load.
Clear incremental marking with knurled knob for precise
measurement.
Dual scale allows reading from top or bottom of tool.
EN-21
www.handyforce.com
ENGINE SERVICE TOOL
EN0198 Engine Oil Dipstick For Audi
Tapered 14mm threads designed to start and remove carbon
& dirt or straighten damaged threads in spark plug hole.
Size: M14 x 1.25 ,
Hexagon : 22mm
Material: S45C with heat treatment.
EN0191
Engine oil dipstick applicable to 2009 Audi A4, A5 and A6 with
engines 2.0I FSI, 3.2l FSI and 4.2l FSI.
EN0251 Viscous Fan Hub Spanner
Injector Puller
EN0256 36mm Fan Clutch Tool
EN0278 Crankshaft Seal Installer
Size: 36mm x 380mm.
For removal of thermo, viscous fan hubs.
For Ford Granada 2.4 & 2.9 GM Carlton, Manta & Senator.
Finish: Polish with mirror chrome plated.
This crankshaft seal removal and installer tool has been
introduced for use
on Golf, Touran, Audi A3 (04-) and also for 4 cylinder diesel
engines.
Application: 1.4 Turbo, 1.4 / 1.6 Direct Injection (Petrol), 1.9 / 2.0
SDI, 2.0 TDI and 2.0 common rail (Diesel).
Material: Aluminum and carbon steel.
450PCS Injector Copper Sealing
EN0261 Ring Kit
EN0252 Clutch Spring Compressor
Suitable for Bosch injector system of Mercedes Benz.
Use for Mercedes Benz CDI engines 611.612.613,…..etc.
For removal of thermo, viscous fan hubs, cranked for easy
access.
Size: 32mm x 380mm
Application for BMW 316, 520i, 525i, 530i, 535i, 730i and 735i
and Ford.
9PCS Diesel Injector Seat Cutter
EN0293 Set
EN0249 Water Pump removal Tool Kit
Use for Volkswagen T5 & Touareg 2.5D water pump removal.
Application for engine code BAC, BLK, BPD, BPE.
www.handyforce.com
engines.
Include 3 sizes of reamer chuck for 17, 19 and 21mm is
suitable cleaning for injector nozzle end.
EN-22
Universal copper sealing ring have 15 different size
combinations is suitable for most of popular nozzle of injector
system.
Contents: (each number have 30 piece sealing ring)
No.
O.D
I.D
Thickness
1
15.0mm
7.0mm
2.0mm
2
15.0mm
7.5mm
1.0mm
3
15.0mm
7.5mm
1.5mm
4
15.0mm
7.5mm
2.0mm
5
15.0mm
7.5mm
2.5mm
6
15.0mm
7.5mm
3.0mm
7
16.0mm
7.5mm
1.5mm
8
16.0mm
7.5mm
1.7mm
9
15.5mm
7.5mm
2.0mm
10
16.0mm
7.5mm
2.0mm
11
16.4mm
7.4mm
2.0mm
12
20.0mm
9.4mm
0.9mm
13
13.85mm
7.3mm
1.4mm
14
14.6mm
7.5mm
1.3mm
15
14.6mm
7.5mm
3.0mm
For removing and installing the transmission rear clutch piston
snap ring
adjustable.
Suitable for most American cars and light trucks.
Exhaust Spring Clamp Remover
EN0319 and Installer
Essential for safe, controlled removal of clamps attaching
exhaust to manifold.
Special design provides leverage required to expand the
strong spring clamps.
Application for VW vehicles.
EN-23
www.handyforce.com
ENGINE SERVICE TOOL
EN0329 8PCS Sensor Socket Master Kit
EN0330 Diesel Injector Removal Set
Design for the removal and installation of oxygen sensors, oil
pressure sending units and vacuum switches.
Made by Chrome-Vanadium steel.
Contents:
1PC 1-3/16" (29mm) 1/2" Dr. oil sensor socket.
1PC 7/8"(22mm) slotted 3/8" Dr. PVS, TVS and O2 sensor.
1PC 1-1/16"(27mm) 1/2" Dr. GM thermal sensor switch.
1PC 7/8"(22mm) oxygen sensor socket.
1PC 1-1/16" oil pressure sending unit 3/8" Dr.
1PC 7/8"(22mm) oxygen sensor socket.
1PC 7/8"(22mm) low profile offset oxygen sensor.
1PC 1-1/16" short access socket 3/8" Dr.
Specifically designed for removing Delphi/Bosch diesel
injectors using a slide hammer with 5/8” UNF thread.
Set of 3 adaptors plus a special tool for removing the internal
part of Bosch injectors.
Suitable for Bosch/Delphi injectors as well as Mercedes-Benz
cdi engine on 611, 612, 613…etc.
Hammer weight: 1.8kg.
EN0331 Extra Long Oxygen Sensor Socket
EN0337 Valve Refacing and Seating Tools
For removing and install lambda sensors with a deep-seated
hexagon.
Particularly suitable for the Mercedes-Benz C/E, 602,605,606,
VW, Audi,
Skoda, Seat, BMW. Ford, Opel, Rover, Volvo.
Material: CR-MO steel.
1/2" Dr. length 150 mm(L).
Size: 22mm x 6PT x 150mm(L).
EN0333 112PCS Master Rethread Tool Kit
EN0338 Valve Refacing and Seating Tools
Precision machined tungsten carbide blades produce valve
lambda probe threads.
disassembly.
the inserts.
Contents:
10PCS glow plug rethread tool M8 X 1.0.
10PCS oxygen sensor rethread tool M12 X 1.5.
21 PCS spark plug rethread tool M14 X 1.25.
10PCS oxygen sensor rethread tool M18 X 1.5.
1PC rethread gauge set.
1PC brass cleaning brush.
1PC nylon cleaning brush.
seats with, accurate seat angle, superior seat surface true, flat
seal and seats concentric with valve guide.
Available in a wide range of cutter diameters and angles.
Application:
1PC cutter ø37mm- ø46mm 60° and 45°.
3PCS expandable pilot “T” wrench handle.
150PCS Injector Copper Sealing
EN0339 Ring Kit
EN0334 Injector Seat Cleaning Set
EN0332 VW/Audi Diesel Injector Remover
Universal copper sealing ring have 15 different size
combinations is suitable for most of popular nozzle of injector
Precision machined tungsten carbide blades produce valve
seats with accurate seat angle, superior seat surface true, flat
seal and seats concentric with valve guide.
Available in a wide range of cutter diameters and angles.
application:
5PCS expandable pilot ø5.5mm- ø12.5mm “T” wrench handle.
www.handyforce.com
system.
Contents:(each size have 10 piece copper sealing ring)
O.D x I.D x Thickness:
13.85 x 7.3 x 1.4(mm) 14.6 x 7.5 x 1.3(mm)
Special design to remove the diesel injector form VAG group
TDI engines.
Special two design to fix the injector and pull out with slide
hammer.
Applicable:
For VW, AUDI engine code ALH, AHU, IZ, Seat and Skoda.
EN-24
Suitable for 2.0 TDI engine from VAG group.
To clean the contact surface between the injector and engine
head when making the replacement.
Include cutter holder can made cutter is straight and correct to
attach when do cleaning.
Insert the extension bar in to the cutter for deep hole cleaning.
14.6 x 7.5 x 3(mm)
15 x 7 x 2(mm)
15 x 7.5 x 1(mm)
15 x 7.5 x 1.5(mm)
15 x 7.5 x 2(mm)
15 x 7.5 x 2.5(mm)
15 x 17.5 x 3(mm)
15.5 x 7.5 x 2(mm)
16 x 7.5 x 1.5(mm)
16 x 7.5 x 1.7(mm)
16 x 7.5 x 2(mm)
16.4 x 7.4 x 2(mm)
20 x 9.4 x 0.9(mm)
EN-25
www.handyforce.com
ENGINE SERVICE TOOL
EN0343 VW/Audi Diesel Injector Remover
EN0002 Universal Pulley Holder
The tool designed to trap and hold bolt-on pulleys by the
mounting bolt on most pulleys.
Special design to remove the diesel injector for VAG group TDI
engines.
Special two design to fix the injector and pull out with slide
hammer.
Applicable:
For VW, AUDI TDI engine code ALH, AHU ,IZ, SEAT and
SKODA.
EN0345 VW/ Audi Special Wrench
EN0347 Thin Jaw Bearing Puller
Special angle wrench for VW / Audi TDi, Turbo system.
Size: 3/8”Dr. x 12mm (12PT)
EN0351 Pulley Puller
EN0358 Offset Distributor Clamp Wrench
and dirt or straighten damaged threads in spark plug hole.
Use with deep socket, open ends or boxes wrench.
Thread size: M12 x 1.25.
Hex subtense size: 22mm.
Tapered threads designed to start and remove carbon and dirt
or straighten damaged threads in spark plug hole.
Thread size: M10 x 1.0 and M12 x 1.25.
Hex subtense size : 21mm.
Contains two offset box wrenches sizes 13mm and 15mm.
13mm Application:
1981 and later Ford V6 (3.8L) engines.
1984-1988 Ford Tempo and Topaz 2.3L HSC vehicles.
1986 and later GM Blazers with V6 (2.8L) engines.
15mm Application:
GM "X" body cars with V6 (2.8L) engines.
1982 and later Cadillac V8 (4.1L) engines.
GM V6 (2.8L) engines and 1985 VW Golf.
Use tool by itself or turn with 3/8" Dr. ratchet.
Drop forged steel construction.
Chrome plated to resist corrosion.
Special design for removing bearing in narrow space.
Reach: 93mm.
Applicable bearing dimension: 30-90mm
Jaw thickness: 1.5mm.
Universal Stretch Belt Installation
EN0359 Tool
Removes pressed on 1 or 2 groove pulleys from alternators or
power steering pumps.
Also easily removes alternator bearings.
Adjusted by simple thumbscrew movement.
Tapered threads designed to start and remove carbon and dirt
or straighten damaged threads in spark plug hole.
Thread size: M12 x 1.25 and M14 x 1.25.
Hex subtense size : 21mm.
EN0360
Air Operated Valve Lapper
EN0357 Offset Distributor Clamp Wrench
2PCS universal stretch belt tool.
Universal stretch belt installation tool is available separately for
applications where a tool must be used.
The universal tool is more economical and environmentally
friendly than disposable versions.
Stretch fit installation kit includes a re-usable universal tool and
mounting bolt.
www.handyforce.com
EN-26
Contains two offset box wrenches sizes 1/2" and 9/16".
Use tool by itself or turn with 3/8" Dr. ratchet.
Drop forged steel construction.
Chrome plated to resist corrosion.
Design for operating in tough environments.
Adjustable speed regulator for precise control during operation.
Complete with rubber caps of 20mm, 30mm, 35mm and
45mm.
EN-27
www.handyforce.com
ENGINE SERVICE TOOL
Diesel Engine Glow Plug Repair
EN0361 Kit
EN0363 VW and AUDI Injector Remover
Diesel Engine requires glow plug for combustion process in
Use “U” sleeve or two jaws hook to fix the injector and then
engine cylinder. The heating element in glow plug heat up and
pull out with slide hammer.
drive the cylinders gradually. But the heating elements are very
Applicable for VW and AUDI FSI engines.
delicate and require special tool for removing the glow plug.
EN0364 3PCS Water Pump Tool Kit
Temperature Sensor Special Socket
EN0362
Set
EN0366 3PCS Sensor Socket Set
10PCS Sensor and Diesel
EN0365 Injection Socket Set
Contents:
1PC heated oxygen sensor socket 1/2” Dr. x 7/8" (22mm) x
50mm (L).
1PC vacuum switch socket 3/8” Dr. x 7/8” (22mm) x 30mm (L).
1PC vacuum switch socket 3/8” Dr. x 7/8” (22mm) x 6PT x
80mm (L).
Contents:
1PC 1/2” Dr. x 29mm x 6PT x 90mm (L).
1PC 3/8” Dr. x 7/8” x 6PT x 90mm (L).
1PC 3/8” Dr. x 7/8” x 6PT x 80mm (L).
1PC 1/2” Dr. x 7/8” x 50mm (L).
1PC 3/8” Dr. x 7/8” x 30mm (L).
1PC 1/2” Dr. x 27mm x 12PT x 78mm (L).
15PCS Harmonic Balancer Puller
EN0369 Set
1PC 1/2” Dr. x 22mm x 12PT x 78mm (L).
1PC 1/2” Dr. x 22mm x 6PT x 110mm (L).
1PC 3/8” Dr. x 1” and 1-1/16” x 74mm (L).
1PC 1/2” Dr. x 28mm x 12PT x 78mm (L).
EN0368 9PCS Injector Extractor Set
Slotted sockets in 3/8” Dr. (10, 11, 12, 14mm ) and
Material: Chrome Molybdenum with S45C steel.
1/2” Dr. (17, 19mm) x 6PT x 77mm(L).
For the assembly of top and side wired temperature sensors
, thermo switches and other components.
This set allows the crankshaft rotation on TDC-position and the
crankshaft counter hold, during the loosening of the crankshaft
center screw or of the water pump toothed wheel fastening
Also suitable for nuts and bolts of bent pipes.
The slot width is 7.4mm, 8.8mm, 9.1mm, 10.5mm, 13.3mm
and 14.4mm.
screw.
It is also suitable for removal or extraction of the water pump
toothed wheel and water pump itself.
On socket rail.
Suitable for VW T5, Touareg 2.5L 5 cylinder TDI engines.
EN0367 5PCS Sensor Socket and Thread Chaser Kit
This device removes vibration dampers, balancers, pulleys
and gears with tapped holes.
Force is evenly distributed upon application.
Puller can be used to pull out most objects since it works on
either two or three tapped holes.
Use with a wrench for more winding power.
Contents:
1PC heated oxygen sensor socket 1/2” Dr. x 7/8” (22mm) x 50mm (L).
1PC vacuum switch socket 3/8” Dr. x 7/8” (22mm) x 30mm (L).
1PC vacuum switch socket 3/8” Dr. 7/8” (22mm) x 6 PT x 80mm (L).
2PCS tapered 12mm and 18mm threads designed to start and remove
carbon and dirt or straighten damaged threads in spark plug hole.
www.handyforce.com
EN-28
Applies to most foreign and import vehicles.
This high quality tooling is designed for the removal of stuck
Contents:
and seized injectors.
3PCS cap screw 3/8” - 24 x 2” (L).
Made by S45C steel.
3PCS cap screw 5/16” - 18 x 2” (L).
Total length 350mm (L).
3PCS cap screw M8 x 1.25 P x 80mm (L).
Contents:
3PCS cap screw 3/8” - 16 x 4” (L).
1.75 KGS slide hammer.
1PC 5/8” main center bolt.
M17 x 1.0 adaptor.
1PC 4 slot yoke.
M27 x 1.0 adaptor for Bosch injector nozzle.
1PC pointed shaft protector.
Puller w/M12 x 1.75 P adaptor.
EN-29
www.handyforce.com
ENGINE SERVICE TOOL
8PCS Ford Diesel Engine Injection
EN0370 Timing Kit
Applications:
1600cc and 1800cc diesel engines fitted to Ford Fiesta, Escort,
Orion, P100, Sierra and Mondeo models.
Also suitable for 2500cc DI engines on 1985 and later Ford
Transit Vans and Galaxy 1900cc TD vehicles.
EN0378 19PCS Glow Plug Removal Set
EN0382 Piston Ring Filer
By using the bracket the filer may be screwed to the work
bench or can be held in a bench vise.
To file piston rings.
Lay the ring on top of the guide plate and against the tapered
locators.
Compress the ring to force the ends lightly against the sides of
the cutting wheel.
Turn the handle in the direction indicated be the arrow to
produce a clean parallel cut.
EN0379 16PCS Glow Plug Removal Set
EN0377
6PCS Diesel Injector and
Lambda Sensor Socket Set
PSA HDI Injection Nozzles
EN0376 Removal Set
Applications:
Hexagonal sockets for removal of the electrical solenoid from
modern injectors.
Applications:
1/2”Dr. x 78mm length.
25mm Hex-Siemens injectors as found on PSA, Ford,
Toyota...etc.
27mm Hex-Siemens Piezo injectors as found on PSA etc.
29mm Hex-Bosch injectors.
Universal Camshaft Pulley
EN0381 Holding Tool
Complete set for removing PSA HDI BOSCH and SIEMENS
injectors without dismounting the cylinder head.
Equipped with a pulling easily remove injectors and a blower
adapter to calm the injector seats.
Engines: PSA 2.0,HDI, DW10 and DW12.
4PCS Diesel Injector and Lambda
EN0380 Sensor Socket set
Applications:
Hexagonal sockets for removal of the electrical solenoid from
modern injectors.
Pin size: 5, 6, 8, 10mm.
Contents:
1PC Hex 12mm spindle, Hex30mm nut cone center tool.
1PC Drill installer.
2PCS 3-1/4”-28 UNF, Hex 8mm.
2PCS diameter 6 mm x 3.5 x 40L.
1PC 3mm alley key.
1PC 9.7mm square socket.
1PC 7 x 5.5 drill.
1PC 9 x 5.5 drill.
1PC T-handle.
2PCS diameter 3.5 drill ×2pcs.
1PC M10 x P10 tap.
1PC M8×1.0 tap.
1PC 13-1/4”-28UNF tap.
1PC 8 x 5.5 drill.
1PC M12 x 1.25P tap.
1PC 10.8 x 5.5 tap.
www.handyforce.com
1/2” Dr. × 78mm length.
25mm Hex-Siemens injectors as found on PSA, Ford, Toyota
etc.
Contents:
1PC Hex 12mm spindle, Hex30mm nut cone center tool.
1PC Drill installer.
2PCS 3-1/4”-28 UNF, Hex 8mm.
2PCS diameter 6 mm x 3.5 x 40L.
1PC 3mm alley key.
1PC 9.7mm square socket.
1PC 7 x 5.5 drill.
1PC 9 x 5.5 drill.
1PC T-handle.
2PCS diameter 3.5 drill ×2pcs.
1PC M10 x P10 tap.
1PC M8×1.0 tap.
1PC 13-1/4”-28UNF tap.
EN-30
27mm Hex-Siemens Piezo injectors as found on PSA etc.
EN-31
www.handyforce.com

ENGINE SERVICE TOOL - force tool of auto repair tool automotive

Transcription

Similar documents

Display Specifications

EUI/EUP Solutions

Steeda Underdrive Pulleys (Late 01-04 GT)

geared up - ADS, Inc.

Central Technology Services

VSI-DI English

6.0L Power Stroke® Diesel Injector

LeverEdge™ Contrast Injector

HydraTec Cyl Service