Cervini

Rev. 8/15
Page 1
Part #2231
2015 Ford Mustang C-series Wing
Notice: Install new, unpainted parts according to these instructions!
Then remove parts, paint them and re-install.
Painted or Altered Parts are Non-Refundable!
IMPORTANT: READ INSTALLATION INSTRUCTIONS COMPLETELY BEFORE INSTALLING
Step 1
TOOLS: TAPE, FISHING LINE, 10 MM SOCKET, EXT, RATCHET, NEEDLE NOSE PLIERS
Fig. A.
Remove the factory spoiler (if equipped). Open the trunk and remove the
fasteners that secure the spoiler to the trunk lid. Disengage the plastic clips
using needle nose pliers. The factory spoiler is also held in place with 2-sided
tape that must be completely removed.
NOTE: CAUTION MUST BE TAKEN DURING THIS STEP, THE TRUNK LID
CAN BE DENTED EASILY.
Use masking tape to protect the paint around the perimeter of the factory
spoiler. Use fishing line and a bondo spreader to cut through the 2-sided tape,
this works well for removing the spoiler. Remove all of the glue and the tape
from the trunk.
Fig. B.
Step
1:::
Step
2
Read over the three options for attachment and select the method that you
prefer.
Option
Step
1::: A
TOOLS: DROP CLOTH, 1/4” DRILL BIT, CORDLESS DRILL, DRMEL OR UNIBIT, BLOCK OF WOOD
Drill/No Tape- For vehicles equipped with a OEM spoiler. Drilling Required.
After the OEM spoiler has been removed, you will see 4 holes at the rear of
the trunk that the new Cervini spoiler will attach to. There are also two locater
holes that the OEM spoiler used located on the outer edge of the trunk lid. You
will need to drill through these holes for this installation method. (If you do not
want to drill into your trunk use Option B). Place a drop cloth directly under the
area of the trunk that needs to drilled to catch metal shavings. The trunk needs
TOOLS & MATERIALS REQUIRED
BONDO SPREADER OR PLASTIC SCRAPER
FISHING LINE
MASKING OR PAINTERS TAPE
QTY
PART #2231
DESCRIPTION
6
1/4” X 20 X 3/4” BOLT
6
6
10 MM SOCKET (1/4” DRIVE RECOMMENDED)
HARDWARE #
11 MM OR 7/16” SOCKET (1/4” DRIVE RECOMMENDED)
13003
SOCKET EXTENSION
1/4” X 20 WASHER
33004
RATCHET
PLASTIC T-STRIPS
TEC-001
1/4” DRILL BIT (OPTIONAL)
9
ROUND GASKETS
P9112
1/16” DRILL BIT (OPTIONAL)
2
PRE CUT 2-SIDED TAPE
CORDLESS DRILL
NEEDLE NOSE PLIERS
DROP CLOTH
DREMEL OR UNIBIT
6” SECTION OF A 2”x4”
3656 N. MILL ROAD, VINELAND, NEW JERSEY 08360 • TECH INFO 1-800-488-6057
Page 2
Step
1:::A cont’d
Option
Fig. C.
to be supported with a 6” section of a 2”x4” as shown in Fig.A. Slowly close
the trunk lid until it makes contact with the 2”x4”. Drill through the holes and
through the underside reinforcement using a 1/4” drill bit as shown in Fig. B.
Open the trunk and use a dremel or unibit to oversize the hole you drilled in the
reinforcement. It needs to be large enough to accept the 1/4” washer included in
your hardware packet as shown in Fig. C. If you chose Option A skip to Step 3.
Fig. D.
Step
1:::B
Option
Tape/No Drill- For vehicles equipped with a OEM spoiler.
NO DRILLING REQUIRED.
Omit the holes that need to be drilled in option A. Use the precut 2-sided tape
as the attachment point on the outer pedestals as shown in Fig. D.
If you chose Option B skip to Step 3.
Step
1::: C
Option
TOOLS: DROP CLOTH, 1/4” & 1/16” DRILL BIT, CORDLESS DRILL, DRMEL OR UNIBIT
Option C: Drilling required. For vehicles WITHOUT a OEM spoiler.
Fig. E.
Locate the plastic T-Strips (drill guides) in your hardware packet and place
them into the 6 threaded inserts on your new Cervini spoiler. Apply a small
piece of masking tape to hold them in place so they don’t fall out, as shown in
Fig. E. Place the spoiler on the trunk and align the spoiler far enough back so
the bottom of the pedestals do not overhang the trunk and are even from left
to right.
After the spoiler is placed in the desired location on the trunk, apply masking
or painters tape to the “legs” of the T-Strips (drill guides) to hold them down on
the trunk as shown in Fig. F.
Fig. F.
Carefully remove the spoiler so that the T-Strips (drill guides) remain on the
trunk.
Open the trunk and place a drop cloth directly under the area of the trunk that
needs to drilled to catch metal shavings. The trunk needs to be supported
with a 6” section of a 2”x4” as shown in Fig.A. Slowly close the trunk lid until
it makes contact with the 2”x4”. Drill through the T-Strips (drill guides) and
into the trunk using a 1/16” drill bit. Remove the T-Strips (drill guides) and
drill through the 1/16” holes with a larger 1/4” drill bit. Make sure you also drill
completely through the underside reinforcement.
Next use a dremel or unibit to oversize the hole you drilled in the reinforcement.
It needs to be large enough to accept the 1/4” washer included in your hardware
packet as shown in Fig. C.
3656 N. MILL ROAD, VINELAND, NEW JERSEY 08360 • TECH INFO 1-800-488-6057
Page 3
Step
1:::
Step
3
Fig. G.
Now that you have test fit your spoiler and prepped the trunk lid for installation
you can remove the spoiler and proceed to paint. (Follow the post cure and
paint instructions located on the label affixed to your C-series Spoiler).
Step
1:::
Step
4
After the spoiler has been painted, install the round foam gaskets to center to
each insert as shown in Fig. G&H.(If you chose option B do not install the foam
gasket to the 2 front inserts on the outer pedestals).
If you had a OEM spoiler, install the foam gasket to the trunk around the extra
holes not being used for installation as shown in Fig. I&J. Use extra care when
placing the gaskets. If they are not centered you may need to trim them so they
are not visible after installation.
Step
1:::
Step
5
Fig. H.
TOOLS: 7/16” or 11 MM SOCKET, EXTENTSION, RATCHET
Install your C-Series Spoiler using the bolts and washers supplied with your
hardware packet. Tighten the bolts down using a 7/16” or 11 mm socket until
they are secure. DO NOT over tighten.
Fig. I.
Fig. J.
3656 N. MILL ROAD, VINELAND, NEW JERSEY 08360 • TECH INFO 1-800-488-6057