460SJ Telescopic Boom Lift

460SJ Telescopic Boom Lift
Applications
•
•
•
•
•
•
•
•
Facilities maintenance
Electricians
Plumbers
All maintenance and
construction work
Factory fit outs before
electrical power is connected
Ideal tilt up panel installation
Steel building installation
Steel cladding contractors
Jib boom and basket rotate allow
additional functionality and access
to hard to reach positions
Low maintenance steel platform with
non-skid mesh floor, and side entry
gate. Enclosed foot switch
Straight boom function
provides increased
outreach and allows fast
operation from ground to
full height using boom lift
and telescope and jib
Perkins 4 cylinder water
cooled diesel engine and
transmission pump to match
drive and function power and
performance requirements
with a quieter engine and
lower operating cost
One handed operation for
operator comfort and control.
Proportional drive controller
gives smooth control
Load Sensing System
Cylinder boots protect
cylinder shafts from debris
and contaminants
Front axle oscillates when travelling with
counterweight over steer tyres, assists in
accessing difficult sites
Urethane filled, puncture
proof lug tyres
Tie down and lifting lugs
for ease of transport
131 JLG
Proportional controller for
lift and lower and boom
swing give smooth control
4 wheel drive with hydraulic piston 2 speed motors,
gear reduction hubs and spring applied brakes for
4 wheel drive traction, provides maximum traction
and ease of steering
www.jlg.com.au
460SJ Telescopic Boom Lift
QUESTIONS TO ASK
Specifications
•
•
•
•
•
•
Performance:
What are the ground conditions in the work area?
What are the site conditions travelling around the site?
What is the working height needed for the job?
What is the outreach required for the job?
Do you need an extension lead outlet in the platform?
Will an inbuilt Miller 5.5kVA generator make the job easier?
KEY SELLING POINTS
• S mooth control, proportional hydraulic 4 wheel drive, with two speed ranges
• Proportional lift and swing controls at the platform
• Oscillating front steer axle with the boom within 10 degrees of centre,
assists 4 wheel drive traction
• Jib boom and basket rotate
• Cylinder boots protect cylinder rods from overspray and contaminants
• Lug pattern urethane filled tyres
• Multi axis 4 degree level sensor
• Plug in JLG analyser at platform and base to indicate system functions
for servicing and adjustment
• Perkins 404C-22 4 cylinder 2.216 litre diesel engine, 50HP/37kW @ 2800rpm,
reduces noise, vibration, emissions and runs at a slower speed to reduce fuel use
Platform Height (max.)
Working Height
Platform Rotation Angle
Jib Raise Angle
Jib Lower Angle
Jib Articulation Range
Maximum Horizontal Outreach
Lift Time
Lower Time
Platform Capacity
Slewing Angle
Continuous Slew
14.02m
16.02m
180°
70°
60°
130°
12.34m
29 sec
22 sec
230kg
360°
Yes
Dimensions:
Stowed Length
8.84m
Stowed Height
2.39m
Overall Width
2.30m
Wheelbase2.34m
Ground Clearance
0.32m
Platform Width
2.44m
Platform Length
0.91m
Overall Jib Length
1.83m
Tailswing0.86m
Axle Oscillation Standard
Std
Power:
Power Source
Engine Make
Engine Model
Engine Power
Genset
Auxiliary Power
Diesel
Perkins
404C-22
37kW
5.5kVA Miller
12V
Travel:
Tyre Size
12 x 16.5
Tyre Type
Urethane Filled
Inside Turn Radius
2.01m
Outside Turn Radius
5.3m
Gradeability45%
Drive Speed
7.2km/h
Maximum Ground Bearing Pressure
4.06kg/cm2
Weights and Capabilities:
Fuel Tank Capacity
Hydraulic Tank Capacity
Operating Weight
131 JLG
98.5 Ltr
159 Ltr
7,930kg
www.jlg.com.au