Grundfos Direct Sensor™

Transcription

GRUNDFOS DATA BOOKLET
Pressure sensors
Table of contents
1.
2.
Product introduction
3
Type key
4
Relative-Pressure sensor, Industry (RPI)
5
RPI / RPI +T general data
RPI, 0 - 0.6 bar (0 - 8.7 psi)
RPI, 0 - 1.0 bar (0 - 14.5 psi)
RPI, 0 - 1.6 bar (0 - 23.2 psi)
RPI, 0 - 2.5 bar (0 - 36.3 psi)
RPI, 0 - 4.0 bar (0 - 58.0 psi)
RPI, 0 - 6.0 bar (0 - 87.0 psi)
RPI, 0 - 10.0 bar (0 - 145.0 psi)
RPI, 0 - 16.0 bar (0 - 232.1 psi)
RPI, 0 - 25.0 bar (0 - 362.6 psi)
3.
4.
5.
6.
7.
2
5
6
7
8
9
10
11
12
13
14
Differential-Pressure sensor,
Industry (DPI)15
DPI, general data
DPI, 0 - 0.6 bar (0 - 8.7 psi)
DPI, 0 - 1.0 bar (0 - 14.5 psi)
DPI, 0 - 1.2 bar (0 - 17.4 psi)
DPI, 0 - 1.6 bar (0 - 23.2 psi)
DPI, 0 - 2.5 bar (0 - 36.3 psi)
DPI, 0 - 4.0 bar (0 - 58.0 psi)
DPI, 0 - 6.0 bar (0 - 87.0 psi)
DPI, 0 - 10.0 bar (0 - 145.0 psi)
15
16
17
18
19
20
21
22
23
Industry (DPI V.2)
24
DPI V.2, general data
DPI V.2, 0 - 0.6 bar (0 - 8.7 psi)
DPI V.2, 0 - 1.0 bar (0 - 14.5 psi)
DPI V.2, 0 - 1.6 bar (0 - 23.2 psi)
DPI V.2, 0 - 2.5 bar (0 - 36.3 psi)
DPI V.2, 0 - 4.0 bar (0 - 58.0 psi)
DPI V.2, 0 - 6.0 bar (0 - 87.0 psi)
DPI V.2, 0 - 10.0 bar (0 - 145.0 psi)
DPI V.2, 0 - 16.0 bar (0 - 232.1 psi)
24
25
26
27
28
29
30
31
32
Relative-Pressure sensor, Standard (RPS) 33
RPS, general data
RPS, 0 - 0.6 bar (0 - 8.7 psi)
RPS, 0 - 1.0 bar (0 - 14.5 psi)
RPS, 0 - 1.6 bar (0 - 23.2 psi)
RPS, 0 - 2.5 bar (0 - 36.3 psi)
RPS, 0 - 4.0 bar (0 - 58.0 psi)
RPS, 0 - 6.0 bar (0 - 87.0 psi)
RPS, 0 - 10.0 bar (0 - 145.0 psi)
33
34
35
36
37
38
39
40
Standard (DPS)
41
DPS, general data
DPS, 0 - 0.6 bar (0 - 8.7 psi)
DPS, 0 - 1.0 bar (0 - 14.5 psi)
DPS, 0 - 1.6 bar (0 - 23.2 psi)
DPS, 0 - 2.5 bar (0 - 36.3 psi)
DPS, 0 - 4.0 bar (0 - 58.0 psi)
DPS, 0 - 6.0 bar (0 - 87.0 psi)
41
42
43
44
45
46
47
Product range
48
RPI sensor
DPI V.2 sensor
DPI sensor
RPS, DPS sensor
48
49
50
50
8.
Accessories
51
Sensor interface, SI 001 PSU
M12 cable
Capillary tube
Adaptor for mounting in Grundfos CR pumps
Sensor interface, SI 010 CNV
51
51
51
51
52
Appendix
53
Installation of RPI, DPI sensor
53
10. Grundfos Product Center
54
9.
1. Product introduction
This data booklet deals with Grundfos pressure
sensors.
TM04 5034 2409 - TM04 7865 2410
TM04 7866 2410 - TM05 4752 2512
Differential-pressure sensor
Grundfos pressure sensors
Three different types of pressure are used in pressure
measurement:
• Absolute pressure: the measured value is zeroreferenced against a vacuum.
• Relative pressure: the measured value is zeroreferenced against the ambient air pressure.
• Differential pressure: the measured value is the
difference between two pressures.
The Grundfos pressure sensor range contains relativeand differential-pressure sensors as well as relativeand differential-pressure sensors combined with
temperature sensors. The latter are able to measure
temperatures ranging from 0 to 100 °C (32 to 212 °F),
allowing the Grundfos sensors to be used for a wide
range of applications.
Relative-pressure sensor
The central part of a relative-pressure sensor is a
sensor chip which transforms the pressure into
electrical signals. The difference between the ambient
air pressure and the system pressure will cause the
sensor chip to warp which is registered as a change of
resistance in the strain gauges of a Wheatstone
bridge. The change in resistance is converted into an
analog output signal. The relative-pressure sensor
combined with temperature sensor also transforms the
temperature of the medium into electrical signals.
A microprocessor calibrates, conditions and sends the
analog output signals. The pressure signals are
temperature-compensated and linearised for the
influence of temperature variations.
TM03 4055 1406
Fig. 1
The central part of a differential-pressure sensor is a
sensor chip which transforms the differential pressure
into electrical signals. The difference between the two
system pressures on either side of the chip, called the
differential pressure, will cause the sensor chip to
warp. This is registered as a change of resistance in
the strain gauges of a Wheatstone bridge. The change
in resistance is converted into an analog output signal.
The sensors that include temperature measurement
also transform the temperature of the medium into
electrical signals.
1
Fig. 2
Schematic view of how the sensor chip is
affected by pressure on both sides
Sensor chip
The steady-state properties of silicon protect the
sensor chip against wear and tear. Lifelong nanocoating protection enables direct measurement (wetwet) in a cost-effective packaging for aggressive
media. The secret is a metal-glass alloy coating,
Silicoat®, which is extremely resistant to corrosion.
Compared to conventional sensor technologies, which
encapsulate the unprotected measuring cell to protect
it from the medium, Silicoat ® ensures protection of the
sensor chip from aggressive media (pH2 - pH11) at
temperatures up to 120 °C (248 °F) for the entire life of
the product.
3
1
Type key
This type key is common to all Grundfos Direct Sensors™ and thus not only specific to pressure sensors.
Type designation
XXX
/ X.X-XXX
X
/X
/X
/X
X.XX
XX
/ XXX
/ XX
/ XX
Product group
Pressure sensors:
DPD: Differential Pressure sensor Digital
DPI: Differential Pressure sensor Industrial
DPS: Differential Pressure sensor Standard
LPS: Leader Pressure sensor Standard
RPD: Relative Pressure sensor Digital
RPI: Relative Pressure sensor Industrial
RPS: Relative Pressure sensor Standard
VFI: Vortex Flow sensor, Industry
Pressure components:
DPC: Differential Pressure sensor Component
RPC: Relative Pressure sensor Component
Flow sensors:
MFS: Multi Flow sensor Standard
VFD: Vortex Flow sensor Digital
VFI: Vortex Flow sensor Industrial
VFS: Vortex Flow sensor Standard
Range
Unit
Pressure: b: bar; p: psi - Flow: m: m3/h; g: gallons/min; l: litres/min
Generation
1: 1st generation; 2: 2nd generation; 3: 3rd generation; etc.
Electrical output type
B: 0-10 V; C: 4-20 mA, 2 wires; D: 2 x 0.5 - 3.5 V; E: 2 x 0.5 - 4.5 V; F: 2 x 0-10 V;
G: 4-20 mA, 3 wires; H: Genibus protocol / RS485 (UART);
I: V-bus protocol / Open-drain; J: LPS protocol / Tx: TTL (UART), Rx: Pulse;
K: OEM protocol / TTL (open-drain) (UART); L: 0.5 - 3.5 V;
M: Redwolf protocol / TTL (UART); N: SQuba protocol / TTL (UART); P: Passive;
Q: Self-configuring Redwolf protocol / TTL (UART) or 2 x 0.5 - 3.5 V
Sensor connector or cable type and cable connector in sensor end
A: Grundfos cover, 4-pin male; B: FCI 90312-004LF/77138-101, unscreened 4 wire cable;
C: MPE-Gerry BL12-700, overmoulded, unscreened 4-wire cable;
D: FCI 90312-004LF/77138-101, overmoulded, screened 4-wire cable;
E: TE snap-on, female, angled, screened 3-wire cable and pig tail. Screen and pig tail
connected to GND pin; I: TE snap-on, female, straight, unscreened 4-wire cable;
J: TE snap-on, female, straight, screened 4-wire cable. Screen connected to GND pin;
L: TE snap-on, female, angled, unscreened 4-wire cable;
M: M12x1, female, straight, screened 4-wire cable;
N: M12x1, 4-pin male; S: TE snap-on cover, 4-pin male; V: PCB pads
Cable length
Cable length in metres (length below 1 metre is denoted without a "0" before the dot. Example:
105 mm is denoted .105)
Cable connector opposite sensor
B: FCI 90312-004LF/77138-101; C: CKM 42010107/42010326, gold plated; D: AMP 103648-3/104479-9;
E: Molex 51004-0400/50011-8000; F: AMP 172167-1/0-170365-1;
G: TE Val-U-Lok 794954-4/794958-2, gold plated; H: Phoenix SACC-M 8MS-4CON-M-0.34-SH;
J: JST XHP-4/SXH-001T-P0.6; K: JST ZER-04V-S/SZE-002TP0.X:\DK\bje\Proj\TekniskMarketing\Sensor_IDS\Databooklet\Pressure Sensors\GB3 / EMiCO 0420500;
L: Lumberg 3510-04 K02; N: Lumberg 3510-04 K03;
P: Molex 43025-0400/43030-0005, 43030-001 / Cembre 1910.M16N; Q: Molex 43025-0400/43030-0006;
R: Molex 51004-0400/50011-8000 / Cembre 1900.M12;
S: Molex 51004-0400/50011-8000 / TE ring terminal 32859-1; T: TE RJ11 2044156-3, gold flash;
U: JST PHR-4/SPH-002T-P0.5S; W: JST XAP-04V-1/SXA-001T-P0.6; X: Open ended;
Y: 4x TE wire pin 966 066-5; Z: Hirose DF1E-4S-2.5C
Sealing material and enclosure class
1st character: E: EPDM; M: Both EPDM and FKM included; S: EPDM sealing cap and FKM O-rings; V: FKM;
2nd character: G: Gel-filled
3rd character: 2: IP20; 4: IP44; 5: IP55; 6: IP67
Material
The first character represents the flow pipe or housing for DPS, the second represents the mechanical connection part.
B: Brass (leaded); C: Composite; G: Cast iron; L: Low lead brass ( ≤ 0.25 % lead);
Q: Stainless steel flow pipe with composite insert (QT); S: Stainless steel
Dimension of mechanical connection
01: 10 mm; 02: 1/4"; 03: 1/2"; 04: 3/4"; 05: 1"; 06: 6 mm; 07: 1 1/4"; 08: 8 mm; 09: 1 1/2"; 10: 2"; 11: 21/2"; 12: 3"; 13: 4";
14: 14.3 mm; 15: 15 mm; 17: 7/16"; 18: 18 mm; 19: 18.75 mm; 21: 21.5 mm; 24: 1/8";
30: DIN PN 25/40 DN 18/25/32, ANSI B16.5 Class 300 - 1 1/4"; 31: DIN PN 16/25 DN 40, ANSI B16.5 Class 300 - 2";
32: DIN PN16/25 DN 50, ANSI B16.5 Class 300 - 2"; 33: ISO/DIN PN 25/40 DN 65; 34: ANSI B16.5 Class 300 - 2.5";
35: ISO/DIN PN 25/40 DN 80; 36: ANSI B16.5 Class 300 - 3"; 37: ISO/DIN PN 16 DN 100; 38: ANSI B16.5 Class 300 - 4";
51: f1" - G 3/4; 52: f1 1/4" - G 1; 63: G 1/2 with ventilation opening; 64: 15.5 mm with ventilation opening
Mechanical connection type
B: BSPT (ISO 7/1); C: Compression; F: Flange; G: Flange and BSPP (ISO 228/1); K: Clip; L: Special clip; M: NPSM; N: NPT;
O: Groove for O-ring; P: BSPP (ISO 228/1); Q: For union nut; S: Sweat; T: Tube; U: UNF
Packaging
1st character: A: Set with preassembled components; M: Miscellaneous set; P: Spare parts set; S: Set; T: Set variant 2; V: Service set
2nd character: B: Plastic bag; C: Cardboard box; D: Blister pack and cardboard box, standard Grundfos; N: Blister pack, neutral white;
T: Trays and cardboard box; W: Blister pack, standard Grundfos
3rd - 4th character: -1: 1 piece; 10: Bulk 10; 20: Bulk 20; 25: Bulk 25; 50: Bulk 50; 1H: Bulk 100; 5H: Bulk 500; 1A: Bulk 1081
4
X
/ XXXX
2. Relative-Pressure sensor, Industry (RPI)
RPI / RPI +T general data
TM04 7865 2510
Benefits
Fig. 3
RPI / RPI+T sensor
Technical overview
Approvals
• WRAS
• KTW
• ACS.
Certificates
75
+
CE
C, CSA, US
C-Tick
Electrical connections
2
1
3
4
TM06 1070 1514
The relative-pressure sensor, type RPI, from Grundfos
Direct Sensors™ is designed for industrial purposes
and to be mounted directly on the unit, for example a
pump.
The RPI sensors are fully compatible with wet,
aggressive media. They use MEMS sensing
technology in combination with the Silicoat® corrosionresistant coating technology on the sensor chip.
This makes the RPI sensors very robust and ideal for
pump integration and monitoring in harsh
environments.
The RPI+T sensor offers a two-in-one solution with an
addtional temperature measurement.
• RPI+T: pressure and temperature measurement in
one sensor (two-in-one solution)
• compatible with wet, aggressive media
• accurate, linearised and temperature-compensated
output signal
• RPI+T: quick temperature response (direct contact
with medium)
• cost-effective and robust design
• system solution with Grundfos pumps.
Applications
•
•
•
•
•
•
•
•
•
Water treatment and distribution
water utility
water monitoring
HVAC systems
chiller systems
HPC and IT cooling systems
micro CHP
heat pumps
solar systems: heating and cooling.
Fig. 4
RPI
Type: 2-wire (loop powered)
Pin
1
2
Wire colour
Brown
I/O
Features
• RPI+T: wide temperature measuring range: 0-100
°C (32 to 212 °F)
• compact design
• MEMS technology
• standard M12 connector.
Pressure ranges
2
[bars]
[psi]
0 - 0.6
0 - 1.0
0 - 1.6
0 - 2.5
0 - 4.0
0 - 6.0
0 - 10.0
0 - 16.0
0 - 25.0
0 - 8.7
0 - 14.5
0 - 23.2
0 - 36.3
0 - 58.0
0 - 87.0
0 - 145.0
0 - 232.1
0 - 362.6
Power
supply
3
4
White
Blue
Black
Wire not
used
Pressure
signal
4-20 mA
Wire not
used
RPI+T
Type: 4-wire
*
Pin
1
2
3
4
Wire colour
Brown
White
Blue
Black
I/O
Power
supply
Pressure
signal
0-10 V
GND*
Temperature
signal
0-10 V
Common ground for pressure and temperature signals. Power
supply (screened cable): SELV or PELV.
5
2
RPI, 0 - 0.6 bar (0 - 8.7 psi)
Specifications
Pressure
TM04 9240 3510
Measuring range
Accuracy (± 1σ),
0-80 °C (32-176 °F)
Accuracy (± 1σ),
-30 - 100 °C (-22 - 212 °F)
Fig. 5
RPI / RPI+T sensor
Dimensions [mm]
Response time
Resolution
0 - 0.6 bar (0 - 8.7 psi)
± 2 % FS
± 2.5 % FS
< 100 ms
(typical 50 ms)
1/1000 FS
Temperature (only RPI with temperature output)
Measuring range
Accuracy (± 1σ),
0-80 °C (32-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
Response time for sensor
electronics
Resolution
0-100 °C (32-212 °F)
±1K
±2K
< 100 ms
(typical 50 ms)
0.1 K
Media and environment
TM04 9237 3510
B
Medium types
C
A
Fig. 6
mm
in
Medium temperature
(operation)
Ambient air temperature
(operation)
Storage temperature
Humidity
System burst pressure
Liquids, gasses and air, compatible
with wetted materials
-30 - 120 °C (-22 - 248 °F)
-25 - 60 °C (-13 - 140 °F)
-55 - 70 °C (-67 - 158 °F)
0-95 % RH, non-condensing
60 bar (870 psi)
Electrical data (only RPI without temperature output)
Dimensions of RPI / RPI+T sensor
A
B
C
36.95
1.45
110
4.33
ISO 228/1 - G 1/2
Power supply RPI
Output signals
- Signal cut off
Power consumption
Load impedance
Output signals
Maximum cable length
12.5 - 30 VDC
4-20 mA
21 mA
Max. 660 mW
Max. 60 Ω at 12.5 VDC
Max. 600 Ω at 24 VDC
30 m (98 ft)
P max
Fig. 7
TM063358 5214
Electrical data (only RPI with temperature output)
Pressure response of RPI sensor
Power supply RPI+T
Output signals
- Signal cut off
Power consumption
Load impedance
16.6 - 30 VDC
0-10 VDC
11 VDC
Max. 300 mW
Min. 10 kΩ
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Sensor housing
Wetted materials
Silicon-based MEMS sensor
EPDM or FKM
Stainless steel AISI 316 L 1.4404
Corrosion-resistant coating
EPDM or FKM
Environmental standards
Enclosure class
Temperature cycling
Vibration (non-destructive)
Electromagnetic compatibility
0
0
Fig. 8
6
P max
T max
Pressure and temperature response of RPI+T
sensor
TM063359 5214
10V
IP67
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
RPI, 0 - 1.0 bar (0 - 14.5 psi)
Specifications
Pressure
TM04 9240 3510
Measuring range
Accuracy (± 1σ),
0-80 °C (32-176 °F)
Accuracy (± 1σ),
-30 - 100 °C (-22 - 212 °F)
Fig. 9
RPI / RPI+T sensor
Dimensions [mm]
Response time
Resolution
0 - 1.0 bar (0 - 14.5 psi)
± 2 % FS
± 2.5 % FS
< 100 ms
(typical 50 ms)
1/1000 FS
Measuring range
Accuracy (± 1σ),
0-80 °C (32-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
electronics
Resolution
0-100 °C (32-212 °F)
±1K
±2K
< 100 ms
(typical 50 ms)
0.1 K
TM04 9237 3510
B
Medium types
C
A
Fig. 10
mm
in
Medium temperature
(operation)
(operation)
Storage temperature
Humidity
2
-30 - 120 °C (-22 - 248 °F)
-25 - 60 °C (-13 - 140 °F)
-55 - 70 °C (-67 - 158 °F)
60 bar (870 psi)
A
B
C
36.95
1.45
110
4.33
ISO 228/1 - G 1/2
Power supply RPI
Output signals
- Signal cut off
Power consumption
Load impedance
Output signals
12.5 - 30 VDC
4-20 mA
21 mA
Max. 660 mW
30 m (98 ft)
P max
Fig. 11
TM063358 5214
Power supply RPI+T
Output signals
- Signal cut off
Power consumption
Load impedance
16.6 - 30 VDC
0-10 VDC
11 VDC
Max. 300 mW
Min. 10 kΩ
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Sensor housing
Wetted materials
EPDM or FKM
EPDM or FKM
Enclosure class
Temperature cycling
0
0
Fig. 12
P max
T max
IP67
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
TM063359 5214
10V
sensor
7
2
RPI, 0 - 1.6 bar (0 - 23.2 psi)
Specifications
Pressure
TM04 9240 3510
Measuring range
Accuracy (± 1σ),
0-80 °C (32-176 °F)
Accuracy (± 1σ),
-30 - 100 °C (-22 - 212 °F)
Fig. 13
RPI / RPI+T sensor
Dimensions [mm]
Response time
Resolution
0 - 1.6 bar (0 - 23.2 psi)
± 2 % FS
± 2.5 % FS
< 100 ms
(typical 50 ms)
1/1000 FS
Measuring range
Accuracy (± 1σ),
0-80 °C (32-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
electronics
Resolution
0-100 °C (32-212 °F)
±1K
±2K
< 100 ms
(typical 50 ms)
0.1 K
TM04 9237 3510
B
Medium types
C
A
Fig. 14
mm
in
Medium temperature
(operation)
(operation)
Storage temperature
Humidity
-30 - 120 °C (-22 - 248 °F)
-25 - 60 °C (-13 - 140 °F)
-55 - 70 °C (-67 - 158 °F)
60 bar (870 psi)
A
B
C
36.95
1.45
110
4.33
ISO 228/1 - G 1/2
Power supply RPI
Output signals
- Signal cut off
Power consumption
Load impedance
Output signals
12.5 - 30 VDC
4-20 mA
21 mA
Max. 660 mW
30 m (98 ft)
P max
Fig. 15
TM063358 5214
Power supply RPI+T
Output signals
- Signal cut off
Power consumption
Load impedance
16.6 - 30 VDC
0-10 VDC
11 VDC
Max. 300 mW
Min. 10 kΩ
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Sensor housing
Wetted materials
EPDM or FKM
EPDM or FKM
Enclosure class
Temperature cycling
0
0
Fig. 16
8
P max
T max
sensor
TM063359 5214
10V
IP67
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
RPI, 0 - 2.5 bar (0 - 36.3 psi)
Specifications
Pressure
TM04 9240 3510
Measuring range
Accuracy (± 1σ),
0-80 °C (32-176 °F)
Accuracy (± 1σ),
-30 - 100 °C (-22 - 212 °F)
Fig. 17
RPI / RPI+T sensor
Dimensions [mm]
Response time
Resolution
0 - 2.5 bar (0 - 36.3 psi)
± 2 % FS
± 2.5 % FS
< 100 ms
(typical 50 ms)
1/1000 FS
Measuring range
Accuracy (± 1σ),
0-80 °C (32-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
electronics
Resolution
0-100 °C (32-212 °F)
±1K
±2K
< 100 ms
(typical 50 ms)
0.1 K
TM04 9237 3510
B
Medium types
C
A
Fig. 18
mm
in
Medium temperature
(operation)
(operation)
Storage temperature
Humidity
2
-30 - 120 °C (-22 - 248 °F)
-25 - 60 °C (-13 - 140 °F)
-55 - 70 °C (-67 - 158 °F)
60 bar (870 psi)
A
B
C
36.95
1.45
110
4.33
ISO 228/1 - G 1/2
Power supply RPI
Output signals
- Signal cut off
Power consumption
Load impedance
Output signals
12.5 - 30 VDC
4-20 mA
21 mA
Max. 660 mW
30 m (98 ft)
P max
Fig. 19
TM063358 5214
Power supply RPI+T
Output signals
- Signal cut off
Power consumption
Load impedance
16.6 - 30 VDC
0-10 VDC
11 VDC
Max. 300 mW
Min. 10 kΩ
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Sensor housing
Wetted materials
EPDM or FKM
EPDM or FKM
Enclosure class
Temperature cycling
0
0
Fig. 20
P max
T max
IP67
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
TM063359 5214
10V
sensor
9
2
RPI, 0 - 4.0 bar (0 - 58.0 psi)
Specifications
Pressure
TM04 9240 3510
Measuring range
Accuracy (± 1σ),
0-80 °C (32-176 °F)
Accuracy (± 1σ),
-30 - 100 °C (-22 - 212 °F)
Fig. 21
RPI / RPI+T sensor
Dimensions [mm]
Response time
Resolution
0 - 4.0 bar (0 - 58.0 psi)
± 2 % FS
± 2.5 % FS
< 100 ms
(typical 50 ms)
1/1000 FS
Measuring range
Accuracy (± 1σ),
0-80 °C (32-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
electronics
Resolution
0-100 °C (32-212 °F)
±1K
±2K
< 100 ms
(typical 50 ms)
0.1 K
TM04 9237 3510
B
Medium types
C
A
Fig. 22
mm
in
Medium temperature
(operation)
(operation)
Storage temperature
Humidity
-30 - 120 °C (-22 - 248 °F)
-25 - 60 °C (-13 - 140 °F)
-55 - 70 °C (-67 - 158 °F)
60 bar (870 psi)
A
B
C
36.95
1.45
110
4.33
ISO 228/1 - G 1/2
Power supply RPI
Output signals
- Signal cut off
Power consumption
Load impedance
Output signals
12.5 - 30 VDC
4-20 mA
21 mA
Max. 660 mW
30 m (98 ft)
P max
Fig. 23
TM063358 5214
Power supply RPI+T
Output signals
- Signal cut off
Power consumption
Load impedance
16.6 - 30 VDC
0-10 VDC
11 VDC
Max. 300 mW
Min. 10 kΩ
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Sensor housing
Wetted materials
EPDM or FKM
EPDM or FKM
Enclosure class
Temperature cycling
0
0
Fig. 24
10
P max
T max
sensor
TM063359 5214
10V
IP67
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
RPI, 0 - 6.0 bar (0 - 87.0 psi)
Specifications
Pressure
TM04 9240 3510
Measuring range
Accuracy (± 1σ),
0-80 °C (32-176 °F)
Accuracy (± 1σ),
-30 - 100 °C (-22 - 212 °F)
Fig. 25
RPI / RPI+T sensor
Dimensions [mm]
Response time
Resolution
0 - 6.0 bar (0 - 87.0 psi)
± 2 % FS
± 2.5 % FS
< 100 ms
(typical 50 ms)
1/1000 FS
Measuring range
Accuracy (± 1σ),
0-80 °C (32-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
electronics
Resolution
0-100 °C (32-212 °F)
±1K
±2K
< 100 ms
(typical 50 ms)
0.1 K
TM04 9237 3510
B
Medium types
C
A
Fig. 26
mm
in
Medium temperature
(operation)
(operation)
Storage temperature
Humidity
2
-30 - 120 °C (-22 - 248 °F)
-25 - 60 °C (-13 - 140 °F)
-55 - 70 °C (-67 - 158 °F)
60 bar (870 psi)
A
B
C
36.95
1.45
110
4.33
ISO 228/1 - G 1/2
Power supply RPI
Output signals
- Signal cut off
Power consumption
Load impedance
Output signals
12.5 - 30 VDC
4-20 mA
21 mA
Max. 660 mW
30 m (98 ft)
P max
Fig. 27
TM063358 5214
Power supply RPI+T
Output signals
- Signal cut off
Power consumption
Load impedance
16.6 - 30 VDC
0-10 VDC
11 VDC
Max. 300 mW
Min. 10 kΩ
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Sensor housing
Wetted materials
EPDM or FKM
EPDM or FKM
Enclosure class
Temperature cycling
0
0
Fig. 28
P max
T max
IP67
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
TM063359 5214
10V
sensor
11
2
RPI, 0 - 10.0 bar (0 - 145.0 psi)
Specifications
Pressure
TM04 9240 3510
Measuring range
Accuracy (± 1σ),
0-80 °C (32-176 °F)
Accuracy (± 1σ),
-30 - 100 °C (-22 - 212 °F)
Fig. 29
RPI / RPI+T sensor
Dimensions [mm]
Response time
Resolution
0 - 10.0 bar (0 - 145.0 psi)
± 2 % FS
± 2.5 % FS
< 100 ms
(typical 50 ms)
1/1000 FS
Measuring range
Accuracy (± 1σ),
0-80 °C (32-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
electronics
Resolution
0-100 °C (32-212 °F)
±1K
±2K
< 100 ms
(typical 50 ms)
0.1 K
TM04 9237 3510
B
Medium types
C
A
Fig. 30
mm
in
Medium temperature
(operation)
(operation)
Storage temperature
Humidity
-30 - 120 °C (-22 - 248 °F)
-25 - 60 °C (-13 - 140 °F)
-55 - 70 °C (-67 - 158 °F)
60 bar (870 psi)
A
B
C
36.95
1.45
110
4.33
ISO 228/1 - G 1/2
Power supply RPI
Output signals
- Signal cut off
Power consumption
Load impedance
Output signals
12.5 - 30 VDC
4-20 mA
21 mA
Max. 660 mW
30 m (98 ft)
P max
Fig. 31
TM063358 5214
Power supply RPI+T
Output signals
- Signal cut off
Power consumption
Load impedance
16.6 - 30 VDC
0-10 VDC
11 VDC
Max. 300 mW
Min. 10 kΩ
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Sensor housing
Wetted materials
EPDM or FKM
EPDM or FKM
Enclosure class
Temperature cycling
0
0
Fig. 32
12
P max
T max
sensor
TM063359 5214
10V
IP67
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
RPI, 0 - 16.0 bar (0 - 232.1 psi)
Specifications
Pressure
TM04 9240 3510
Measuring range
Accuracy (± 1σ),
0-80 °C (32-176 °F)
Accuracy (± 1σ),
-30 - 100 °C (-22 - 212 °F)
Fig. 33
RPI / RPI+T sensor
Dimensions [mm]
Response time
Resolution
0 - 16.0 bar (0 - 232.1 psi)
± 2 % FS
± 2.5 % FS
< 100 ms
(typical 50 ms)
1/1000 FS
Measuring range
Accuracy (± 1σ),
0-80 °C (32-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
electronics
Resolution
0-100 °C (32-212 °F)
±1K
±2K
< 100 ms
(typical 50 ms)
0.1 K
TM04 9237 3510
B
Medium types
C
A
Fig. 34
mm
in
Medium temperature
(operation)
(operation)
Storage temperature
Humidity
2
-30 - 120 °C (-22 - 248 °F)
-25 - 60 °C (-13 - 140 °F)
-55 - 70 °C (-67 - 158 °F)
60 bar (870 psi)
A
B
C
36.95
1.45
110
4.33
ISO 228/1 - G 1/2
Power supply RPI
Output signals
- Signal cut off
Power consumption
Load impedance
Output signals
12.5 - 30 VDC
4-20 mA
21 mA
Max. 660 mW
30 m (98 ft)
P max
Fig. 35
TM063358 5214
Power supply RPI+T
Output signals
- Signal cut off
Power consumption
Load impedance
16.6 - 30 VDC
0-10 VDC
11 VDC
Max. 300 mW
Min. 10 kΩ
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Sensor housing
Wetted materials
EPDM or FKM
EPDM or FKM
Enclosure class
Temperature cycling
0
0
Fig. 36
P max
T max
IP67
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
TM063359 5214
10V
sensor
13
2
RPI, 0 - 25.0 bar (0 - 362.6 psi)
Specifications
Pressure
TM04 9240 3510
Measuring range
Accuracy (± 1σ),
0-80 °C (32-176 °F)
Accuracy (± 1σ),
-30 - 100 °C (-22 - 212 °F)
Fig. 37
RPI / RPI+T sensor
Dimensions [mm]
Response time
Resolution
0 - 25.0 bar (0 - 362.6 psi)
± 2 % FS
± 2.5 % FS
< 100 ms
(typical 50 ms)
1/1000 FS
Measuring range
Accuracy (± 1σ),
0-80 °C (32-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
electronics
Resolution
0-100 °C (32-212 °F)
±1K
±2K
< 100 ms
(typical 50 ms)
0.1 K
TM04 9237 3510
B
Medium types
C
A
Fig. 38
mm
in
Medium temperature
(operation)
(operation)
Storage temperature
Humidity
-30 - 120 °C (-22 - 248 °F)
-25 - 60 °C (-13 - 140 °F)
-55 - 70 °C (-67 - 158 °F)
60 bar (870 psi)
A
B
C
36.95
1.45
110
4.33
ISO 228/1 - G 1/2
Power supply RPI
Output signals
- Signal cut off
Power consumption
Load impedance
Output signals
12.5 - 30 VDC
4-20 mA
21 mA
Max. 660 mW
30 m (98 ft)
P max
Fig. 39
TM063358 5214
Power supply RPI+T
Output signals
- Signal cut off
Power consumption
Load impedance
16.6 - 30 VDC
0-10 VDC
11 VDC
Max. 300 mW
Min. 10 kΩ
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Sensor housing
Wetted materials
EPDM or FKM
EPDM or FKM
Enclosure class
Temperature cycling
0
0
Fig. 40
14
P max
T max
sensor
TM063359 5214
10V
IP67
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
3. Differential-Pressure sensor, Industry (DPI)
DPI, general data
TM04 4738 0509
Benefits
Fig. 41
DPI sensor
Technical overview
The differential-pressure sensor, type DPI, from
Grundfos Direct Sensors™, is designed for industrial
purposes.
The DPI sensors are fully compatible with wet,
technology in combination with the corrosion-resistant
Silicoat® coating technology on the sensor chip.
This makes the DPI sensors very robust and ideal for
environments.
• Compatible with wet, aggressive media
output signal
Approvals
• WRAS
• KTW
• ACS.
Certificates
75
+
CE
Differential-Pressure sensor, Industry (DPI)
3
C, CSA, US
C-Tick
1
2
3
4
Applications
water utility
water monitoring
HVAC systems
chiller systems
micro CHP
heat pumps
A
PE
Fig. 42
Pin
1
Features
• compact design
• MEMS technology.
Pressure ranges
TM04 9191 3610
•
•
•
•
•
•
•
•
•
[bars]
[psi]
0 - 0.6
0 - 1.0
0 - 1.2
0 - 1.6
0 - 2.5
0 - 4.0
0 - 6.0
0 - 10.0
0 - 8.7
0 - 14.5
0 - 17.4
0 - 23.2
0 - 36.3
0 - 58.0
0 - 87.0
0 - 145.0
Description
Test conductor (can be cut off during mounting).
Do not connect this conductor to the power
supply.
Colour
White
2
Signal conductor
Green
3
GND (earth conductor)
Yellow
4
12-30 V supply voltage
Brown
15
3
DPI, 0 - 0.6 bar (0 - 8.7 psi)
Specifications
TM04 5034 2409
Pressure
Fig. 43
Measuring range
Accuracy (IEC 61298-2)
Response time
Static pressure, p1
Static pressure, p2
Maximum system pressure
Media
Medium temperature
(operation)
Medium temperature (peak)
(peak)
Humidity
DPI sensor
Dimensions [mm]
0 - 0.6 bar (0 - 8.7 psi)
3.5 % FS
< 0.5 s
16 bar (232 psi)
10 bar (145 psi)
16 bar (232 psi)
Liquids, gases and air, compatible
-10 - 70 °C (-14 - 158 °F)
Up to +80 °C (176 °F)
-40 - 70 °C (-40 - 158 °F)
-55 - 90 °C (-67 - 194 °F)
0-95 % (relative), non-condensing
25 bar (362 psi)
Electrical data
Power supply
Output signals
- Signal cut off
F
D
Load impedance
TM03 2059 3505
E
P2
P1
C
A
Fig. 44
mm
in
B
Dimensions of DPI sensor
A
B
C
D
14
6
∅45
77
0.55
0.24
∅1.77
3.03
E
F
7/16 - 20
UNF
0.25"
flare
SW 14
Differential-pressure response of DPI sensor
TM063358 5214
P max
16
Sensor materials
Sensing element
O-ring
Housing
Wetted materials
FKM
EN 1.4305
FKM and PPS
Output signals
Fig. 45
12-30 VDC
4-20 mA
21 mA
Max. 500 kΩ at 24 V
30 m (98 ft)
Enclosure class
Temperature cycling
Immunity
Emission
Weight
IP55
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61000-6-2
EN 61000-6-3
550 g (1.21 lbs)
DPI, 0 - 1.0 bar (0 - 14.5 psi)
Specifications
TM04 5034 2409
Pressure
Fig. 46
Measuring range
Response time
Static pressure, p1
Static pressure, p2
Media
Medium temperature
(operation)
(peak)
Humidity
DPI sensor
Dimensions [mm]
0 - 1.0 bar (0 - 14.5 psi)
2 % FS
< 0.5 s
16 bar (232 psi)
10 bar (145 psi)
16 bar (232 psi)
-10 - 70 °C (-14 - 158 °F)
Up to +80 °C (176 °F)
-40 - 70 °C (-40 - 158 °F)
-55 - 90 °C (-67 - 194 °F)
25 bar (362 psi)
Electrical data
Power supply
Output signals
- Signal cut off
F
D
Load impedance
TM03 2059 3505
E
P2
P1
C
A
Fig. 47
B
3
12-30 VDC
4-20 mA
21 mA
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Housing
Wetted materials
FKM
EN 1.4305
FKM and PPS
mm
in
A
B
C
D
14
6
∅45
77
0.55
0.24
∅1.77
3.03
E
F
7/16 - 20
UNF
0.25"
flare
SW 14
Enclosure class
Temperature cycling
Immunity
Emission
Weight
IP55
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61000-6-2
EN 61000-6-3
550 g (1.21 lbs)
P max
Fig. 48
TM063358 5214
Output signals
17
3
DPI, 0 - 1.2 bar (0 - 17.4 psi)
Specifications
TM04 5034 2409
Pressure
Fig. 49
Measuring range
Response time
Static pressure, p1
Static pressure, p2
Media
Medium temperature
(operation)
(peak)
Humidity
DPI sensor
Dimensions [mm]
0 - 1.2 bar (0 - 17.4 psi)
2 % FS
< 0.5 s
16 bar (232 psi)
10 bar (145 psi)
16 bar (232 psi)
-10 - 70 °C (-14 - 158 °F)
Up to +80 °C (176 °F)
-40 - 70 °C (-40 - 158 °F)
-55 - 90 °C (-67 - 194 °F)
25 bar (362 psi)
Electrical data
Power supply
Output signals
- Signal cut off
F
D
Load impedance
TM03 2059 3505
E
P2
P1
C
A
Fig. 50
B
12-30 VDC
4-20 mA
21 mA
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Housing
Wetted materials
FKM
EN 1.4305
FKM and PPS
mm
in
A
B
C
D
14
6
∅45
77
0.55
0.24
∅1.77
3.03
E
F
7/16 - 20
UNF
0.25"
flare
SW 14
P max
Fig. 51
18
TM063358 5214
Output signals
Enclosure class
Temperature cycling
Immunity
Emission
Weight
IP55
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61000-6-2
EN 61000-6-3
550 g (1.21 lbs)
DPI, 0 - 1.6 bar (0 - 23.2 psi)
Specifications
TM04 5034 2409
Pressure
Fig. 52
Measuring range
Response time
Static pressure, p1
Static pressure, p2
Media
Medium temperature
(operation)
(peak)
Humidity
DPI sensor
Dimensions [mm]
0 - 1.6 bar (0 - 23.2 psi)
2 % FS
< 0.5 s
16 bar (232 psi)
10 bar (145 psi)
16 bar (232 psi)
-10 - 70 °C (-14 - 158 °F)
Up to +80 °C (176 °F)
-40 - 70 °C (-40 - 158 °F)
-55 - 90 °C (-67 - 194 °F)
25 bar (362 psi)
Electrical data
Power supply
Output signals
- Signal cut off
F
D
Load impedance
TM03 2059 3505
E
P2
P1
C
A
Fig. 53
B
3
12-30 VDC
4-20 mA
21 mA
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Housing
Wetted materials
FKM
EN 1.4305
FKM and PPS
mm
in
A
B
C
D
14
6
∅45
77
0.55
0.24
∅1.77
3.03
E
F
7/16 - 20
UNF
0.25"
flare
SW 14
Enclosure class
Temperature cycling
Immunity
Emission
Weight
IP55
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61000-6-2
EN 61000-6-3
550 g (1.21 lbs)
P max
Fig. 54
TM063358 5214
Output signals
19
3
DPI, 0 - 2.5 bar (0 - 36.3 psi)
Specifications
TM04 5034 2409
Pressure
Fig. 55
Measuring range
Response time
Static pressure, p1
Static pressure, p2
Media
Medium temperature
(operation)
(peak)
Humidity
DPI sensor
Dimensions [mm]
0 - 2.5 bar (0 - 36.3 psi)
2 % FS
< 0.5 s
16 bar (232 psi)
10 bar (145 psi)
16 bar (232 psi)
-10 - 70 °C (-14 - 158 °F)
Up to +80 °C (176 °F)
-40 - 70 °C (-40 - 158 °F)
-55 - 90 °C (-67 - 194 °F)
25 bar (362 psi)
Electrical data
Power supply
Output signals
- Signal cut off
F
D
Load impedance
TM03 2059 3505
E
P2
P1
C
A
Fig. 56
B
12-30 VDC
4-20 mA
21 mA
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Housing
Wetted materials
FKM
EN 1.4305
FKM and PPS
mm
in
A
B
C
D
14
6
∅45
77
0.55
0.24
∅1.77
3.03
E
F
7/16 - 20
UNF
0.25"
flare
SW 14
P max
Fig. 57
20
TM063358 5214
Output signals
Enclosure class
Temperature cycling
Immunity
Emission
Weight
IP55
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61000-6-2
EN 61000-6-3
550 g (1.21 lbs)
DPI, 0 - 4.0 bar (0 - 58.0 psi)
Specifications
TM04 5034 2409
Pressure
Fig. 58
Measuring range
Response time
Static pressure, p1
Static pressure, p2
Media
Medium temperature
(operation)
(peak)
Humidity
DPI sensor
Dimensions [mm]
0 - 4.0 bar (0 - 58.0 psi)
2 % FS
< 0.5 s
16 bar (232 psi)
10 bar (145 psi)
16 bar (232 psi)
-10 - 70 °C (-14 - 158 °F)
Up to +80 °C (176 °F)
-40 - 70 °C (-40 - 158 °F)
-55 - 90 °C (-67 - 194 °F)
25 bar (362 psi)
Electrical data
Power supply
Output signals
- Signal cut off
F
D
Load impedance
TM03 2059 3505
E
P2
P1
C
A
Fig. 59
B
3
12-30 VDC
4-20 mA
21 mA
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Housing
Wetted materials
FKM
EN 1.4305
FKM and PPS
mm
in
A
B
C
D
14
6
∅45
77
0.55
0.24
∅1.77
3.03
E
F
7/16 - 20
UNF
0.25"
flare
SW 14
Enclosure class
Temperature cycling
Immunity
Emission
Weight
IP55
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61000-6-2
EN 61000-6-3
550 g (1.21 lbs)
P max
Fig. 60
TM063358 5214
Output signals
21
3
DPI, 0 - 6.0 bar (0 - 87.0 psi)
Specifications
TM04 5034 2409
Pressure
Fig. 61
Measuring range
Response time
Static pressure, p1
Static pressure, p2
Media
Medium temperature
(operation)
(peak)
Humidity
DPI sensor
Dimensions [mm]
0 - 6.0 bar (0 - 87.0 psi)
2 % FS
< 0.5 s
16 bar (232 psi)
10 bar (145 psi)
16 bar (232 psi)
-10 - 70 °C (-14 - 158 °F)
Up to +80 °C (176 °F)
-40 - 70 °C (-40 - 158 °F)
-55 - 90 °C (-67 - 194 °F)
25 bar (362 psi)
Electrical data
Power supply
Output signals
- Signal cut off
F
D
Load impedance
TM03 2059 3505
E
P2
P1
C
A
Fig. 62
B
12-30 VDC
4-20 mA
21 mA
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Housing
Wetted materials
FKM
EN 1.4305
FKM and PPS
mm
in
A
B
C
D
14
6
∅45
77
0.55
0.24
∅1.77
3.03
E
F
7/16 - 20
UNF
0.25"
flare
SW 14
P max
Fig. 63
22
TM063358 5214
Output signals
Enclosure class
Temperature cycling
Immunity
Emission
Weight
IP55
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61000-6-2
EN 61000-6-3
550 g (1.21 lbs)
DPI, 0 - 10.0 bar (0 - 145.0 psi)
Specifications
TM04 5034 2409
Pressure
Fig. 64
Measuring range
Response time
Static pressure, p1
Static pressure, p2
Media
Medium temperature
(operation)
(peak)
Humidity
DPI sensor
Dimensions [mm]
0 - 10.0 bar (0 - 145.0 psi)
2 % FS
< 0.5 s
16 bar (232 psi)
10 bar (145 psi)
16 bar (232 psi)
-10 - 70 °C (-14 - 158 °F)
Up to +80 °C (176 °F)
-40 - 70 °C (-40 - 158 °F)
-55 - 90 °C (-67 - 194 °F)
25 bar (362 psi)
Electrical data
Power supply
Output signals
- Signal cut off
F
D
Load impedance
TM03 2059 3505
E
P2
P1
C
A
Fig. 65
B
3
12-30 VDC
4-20 mA
21 mA
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Housing
Wetted materials
FKM
EN 1.4305
FKM and PPS
mm
in
A
B
C
D
14
6
∅45
77
0.55
0.24
∅1.77
3.03
E
F
7/16 - 20
UNF
0.25"
flare
SW 14
P max
Fig. 66
IP55
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61000-6-2
EN 61000-6-3
550 g (1.21 lbs)
TM063358 5214
Output signals
Enclosure class
Temperature cycling
Immunity
Emission
Weight
23
4
DPI V.2, general data
TM04 7866 2510
Benefits
Fig. 67
DPI V.2 sensor
Technical overview
The combined differential-pressure and temperature
sensor (two-in-one solution), type DPI V.2, from
Grundfos Direct Sensors™ is designed for industrial
purposes and to be mounted directly on the unit, for
example a pump.
The DPI V.2 is used together with a capillary tube in
order to measure the differential pressure between two
points of the system.
The DPI V.2 sensors are fully compatible with wet,
technology in combination with the Silicoat® corrosionresistant coating technology on the sensor chip.
This makes the DPI sensors very robust and ideal for
environments.
• Pressure and temperature measurement in one
sensor (two-in-one solution)
output signal
• quick temperature response (direct contact with
medium)
Approvals
• WRAS
• KTW
• ACS.
Certificates
75
+
CE
C, CSA, US
C-Tick
2
1
3
4
TM06 1070 1514
Differential-Pressure sensor, Industry (DPI V.2)
4. Differential-Pressure sensor, Industry (DPI V.2)
Applications
•
•
•
•
•
•
•
•
•
water utility
water monitoring
HVAC systems
chiller systems
micro CHP
heat pumps
Fig. 68
DPI
Type: 2-wire (loop powered)
• DPI V.2 +T: wide temperature measuring range: 0100 °C (32-212 °F)
• compact design
• MEMS technology
• standard M12 connector.
24
Pin
1
2
Wire colour
Brown
I/O
Features
Pressure ranges
[bars]
[psi]
0 - 0.6
0 - 1.0
0 - 1.6
0 - 2.5
0 - 4.0
0 - 6.0
0 - 10.0
0 - 16.0
0 - 8.7
0 - 14.5
0 - 23.2
0 - 36.3
0 - 58.0
0 - 87.0
0 - 145.0
0 - 232.1
Power
supply
3
4
White
Blue
Black
Wire not
used
Pressure
signal
4-20 mA
Wire not
used
DPI V.2 +T
Type: 4-wire
*
Pin
1
2
3
4
Wire colour
Brown
White
Blue
Black
I/O
Power
supply
Pressure
signal
0-10 V
GND*
Temperature
signal
0-10 V
Common ground for pressure and temperature signals. Power
supply (screened cable): SELV or PELV.
DPI V.2, 0 - 0.6 bar (0 - 8.7 psi)
Specifications
TM04 9239 3510
Pressure
Fig. 69
Measuring range
Accuracy (± 1σ), 0-80 °C
(-32 - 176 °F)
Accuracy (± 1σ), -30 - 100 °C
(8.6 - 284 °F)
Response time
Resolution
Dimensions [mm]
± 2 % FS
± 2.5 % FS
< 100 ms
(typical 50 ms)
1/1000 FS
Temperature (only DPI V.2 with temperature output)
Measuring range (relative)
(-32 - 176 °F)
(-32-212 °F)
electronics
Resolution
DPI V.2 / DPI V.2+T sensor
0 - 0.6 bar (0 - 8.7 psi)
0-100 °C (32-212 °F)
±1K
±2K
< 100 ms
(typical 50 ms)
0.1 K
B
Medium types
TM04 9238 0415
D
C
A
Fig. 70
mm
in
Dimensions of DPI V.2 / DPI V.2+T sensor
Medium temperature
(operation)
(operation)
Storage temperature
Humidity
-30 - 120 °C (-22 - 248 °F)
4
-25 - 60 °C (-13 - 140 °F)
-55 - 70 °C (-67 - 140 °F)
60 bar (870 psi)
Electrical data (only DPI V.2 without temperature output)
A
B
C
D
36.95
1.45
110
4.33
ISO 228/1 G 1/2
7/16 - 20 UNF
0.25" flare
Output signals
Power supply DPI V.2
Output signals
- Signal cut off
Power consumption
Load impedance
12.5 - 30 VDC
4-20 mA
21 mA
Max. 660 mW
30 m (98 ft)
P max
Fig. 71
TM063358 5214
Electrical data (only DPI V.2 with temperature output)
Pressure response of DPI V.2 sensor
Power supply DPI V.2+T
Output signals
- Signal cut off
Power consumption
Load impedance
16.6 - 30 VDC
0-10 VDC
11 VDC
Max. 300 mW
Min. 10 kΩ
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Sensor housing
Wetted materials
EPDM or FKM
EPDM or FKM
Enclosure class
Temperature cycling
0
0
Fig. 72
P max
T max
IP67
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
TM063359 5214
10V
Pressure and temperature response of DPI V.2+T
sensor
25
4
DPI V.2, 0 - 1.0 bar (0 - 14.5 psi)
Specifications
TM04 9239 3510
Pressure
Fig. 73
Measuring range
(32-176 °F)
Accuracy (± 1σ), -30 - 100 °C
(8.6 - 284 °F)
Response time
Resolution
Dimensions [mm]
± 2 % FS
± 2.5 % FS
< 100 ms
(typical 50 ms)
1/1000 FS
(32-176 °F)
(32-212 °F)
electronics
Resolution
0 - 1.0 bar (0 - 14.5 psi)
0-100 °C (32-212 °F)
±1K
±2K
< 100 ms
(typical 50 ms)
0.1 K
B
Medium types
TM04 9238 0415
D
C
A
Fig. 74
mm
in
Medium temperature
(operation)
(operation)
Storage temperature
Humidity
-30 - 120 °C (-22 - 248 °F)
-25 - 60 °C (-13 - 140 °F)
-55 - 70 °C (-67 - 158 °F)
60 bar (870 psi)
A
B
C
D
36.95
1.45
110
4.33
ISO 228/1 G 1/2
7/16 - 20 UNF
0.25" flare
Output signals
Output signals
- Signal cut off
Power consumption
Load impedance
12.5 - 30 VDC
4-20 mA
21 mA
Max. 660 mW
30 m (98 ft)
P max
Fig. 75
TM063358 5214
Output signals
- Signal cut off
Power consumption
Load impedance
16.6 - 30 VDC
0-10 VDC
11 VDC
Max. 300 mW
Min. 10 kΩ
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Sensor housing
Wetted materials
EPDM or FKM
EPDM or FKM
Enclosure class
Temperature cycling
0
0
Fig. 76
26
P max
T max
TM063359 5214
10V
sensor
IP67
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
DPI V.2, 0 - 1.6 bar (0 - 23.2 psi)
Specifications
TM04 9239 3510
Pressure
Fig. 77
Dimensions [mm]
Measuring range
(32-176 °F)
Accuracy (± 1σ), -30 - 100 °C
(8.6 - 284 °F)
Response time
Resolution
0 - 1.6 bar (0 - 23.2 psi)
± 2 % FS
± 2.5 % FS
< 100 ms
(typical 50 ms)
1/1000 FS
(32-176 °F)
(32-212 °F)
electronics
Resolution
0-100 °C (32-212 °F)
±1K
±2K
< 100 ms
(typical 50 ms)
0.1 K
B
Medium types
TM04 9238 0415
D
C
A
Fig. 78
mm
in
Medium temperature
(operation)
(operation)
Storage temperature
Humidity
-30 - 120 °C (-22 - 248 °F)
4
-25 - 60 °C (-13 - 140 °F)
-55 - 70 °C (-67 - 158 °F)
60 bar (870 psi)
A
B
C
D
36.95
1.45
110
4.33
ISO 228/1 G 1/2
7/16 - 20 UNF
0.25" flare
Output signals
- Signal cut off
Power consumption
Load impedance
Output signals
12.5 - 30 VDC
4-20 mA
21 mA
Max. 660 mW
30 m (98 ft)
P max
Fig. 79
TM063358 5214
Output signals
- Signal cut off
Power consumption
Load impedance
16.6 - 30 VDC
0-10 VDC
11 VDC
Max. 300 mW
Min. 10 kΩ
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Sensor housing
Wetted materials
EPDM or FKM
EPDM or FKM
Enclosure class
Temperature cycling
0
0
Fig. 80
P max
T max
IP67
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
TM063359 5214
10V
sensor
27
4
DPI V.2, 0 - 2.5 bar (0 - 36.3 psi)
Specifications
TM04 9239 3510
Pressure
Fig. 81
Measuring range
(32-176 °F)
Accuracy (± 1σ), -30 - 100 °C
(8.6 - 284 °F)
Response time
Resolution
Dimensions [mm]
± 2 % FS
± 2.5 % FS
< 100 ms
(typical 50 ms)
1/1000 FS
(32-176 °F)
(32-212 °F)
electronics
Resolution
0 - 2.5 bar (0 - 36.3 psi)
0-100 °C (32-212 °F)
±1K
±2K
< 100 ms
(typical 50 ms)
0.1 K
B
Medium types
TM04 9238 0415
D
C
A
Fig. 82
mm
in
Medium temperature
(operation)
(operation)
Storage temperature
Humidity
-30 - 120 °C (-22 - 248 °F)
-25 - 60 °C (-13 - 140 °F)
-55 - 70 °C (-67 - 158 °F)
60 bar (870 psi)
A
B
C
D
36.95
1.45
110
4.33
ISO 228/1 G 1/2
7/16 - 20 UNF
0.25" flare
Output signals
Output signals
- Signal cut off
Power consumption
Load impedance
12.5 - 30 VDC
4-20 mA
21 mA
Max. 660 mW
30 m (98 ft)
P max
Fig. 83
TM063358 5214
Output signals
- Signal cut off
Power consumption
Load impedance
16.6 - 30 VDC
0-10 VDC
11 VDC
Max. 300 mW
Min. 10 kΩ
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Sensor housing
Wetted materials
EPDM or FKM
EPDM or FKM
Enclosure class
Temperature cycling
0
0
Fig. 84
28
P max
T max
TM063359 5214
10V
sensor
IP67
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
DPI V.2, 0 - 4.0 bar (0 - 58.0 psi)
Specifications
TM04 9239 3510
Pressure
Fig. 85
Measuring range
(32-176 °F)
Accuracy (± 1σ), -30 - 100 °C
(8.6 - 284 °F)
Response time
Resolution
Dimensions [mm]
± 2 % FS
± 2.5 % FS
< 100 ms
(typical 50 ms)
1/1000 FS
(32-176 °F)
(32-212 °F)
electronics
Resolution
0 - 4.0 bar (0 - 58.0 psi)
0-100 °C (32-212 °F)
±1K
±2K
< 100 ms
(typical 50 ms)
0.1 K
B
Medium types
TM04 9238 0415
D
C
A
Fig. 86
mm
in
Medium temperature
(operation)
(operation)
Storage temperature
Humidity
-30 - 120 °C (-22 - 248 °F)
4
-25 - 60 °C (-13 - 140 °F)
-55 - 70 °C (-67 - 158 °F)
60 bar (870 psi)
A
B
C
D
36.95
1.45
110
4.33
ISO 228/1 G 1/2
7/16 - 20 UNF
0.25" flare
Output signals
- Signal cut off
Power consumption
Load impedance
Output signals
12.5 - 30 VDC
4-20 mA
21 mA
Max. 660 mW
30 m (98 ft)
P max
Fig. 87
TM063358 5214
Output signals
- Signal cut off
Power consumption
Load impedance
16.6 - 30 VDC
0-10 VDC
11 VDC
Max. 300 mW
Min. 10 kΩ
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Sensor housing
Wetted materials
EPDM or FKM
EPDM or FKM
Enclosure class
Temperature cycling
0
0
Fig. 88
P max
T max
IP67
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
TM063359 5214
10V
sensor
29
4
DPI V.2, 0 - 6.0 bar (0 - 87.0 psi)
Specifications
TM04 9239 3510
Pressure
Fig. 89
Measuring range
(32-176 °F)
Accuracy (± 1σ), -30 - 100 °C
(8.6 - 284 °F)
Response time
Resolution
Dimensions [mm]
± 2 % FS
± 2.5 % FS
< 100 ms
(typical 50 ms)
1/1000 FS
(32-176 °F)
(32-212 °F)
electronics
Resolution
0 - 6.0 bar (0 - 87.0 psi)
0-100 °C (32-212 °F)
±1K
±2K
< 100 ms
(typical 50 ms)
0.1 K
B
Medium types
TM04 9238 0415
D
C
A
Fig. 90
mm
in
Medium temperature
(operation)
(operation)
Storage temperature
Humidity
-30 - 120 °C (-22 - 248 °F)
-25 - 60 °C (-13 - 140 °F)
-55 - 70 °C (-67 - 158 °F)
60 bar (870 psi)
A
B
C
D
36.95
1.45
110
4.33
ISO 228/1 G 1/2
7/16 - 20 UNF
0.25" flare
Output signals
- Signal cut off
Power consumption
Load impedance
Output signals
12.5 - 30 VDC
4-20 mA
21 mA
Max. 660 mW
30 m (98 ft)
P max
Fig. 91
TM063358 5214
Output signals
- Signal cut off
Power consumption
Load impedance
16.6 - 30 VDC
0-10 VDC
11 VDC
Max. 300 mW
Min. 10 kΩ
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Sensor housing
Wetted materials
EPDM or FKM
EPDM or FKM
Enclosure class
Temperature cycling
0
0
Fig. 92
30
P max
T max
TM063359 5214
10V
sensor
IP67
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
DPI V.2, 0 - 10.0 bar (0 - 145.0 psi)
Specifications
TM04 9239 3510
Pressure
Fig. 93
Measuring range
(32-176 °F)
Accuracy (± 1σ), -30 - 100 °C
(8.6 - 284 °F)
Response time
Resolution
Dimensions [mm]
± 2 % FS
± 2.5 % FS
< 100 ms
(typical 50 ms)
1/1000 FS
(32-176 °F)
(32-212 °F)
electronics
Resolution
0 - 10.0 bar (0 - 145.0 psi)
0-100 °C (32-212 °F)
±1K
±2K
< 100 ms
(typical 50 ms)
0.1 K
B
Medium types
TM04 9238 0415
D
C
A
Fig. 94
mm
in
Medium temperature
(operation)
(operation)
Storage temperature
Humidity
-30 - 120 °C (-22 - 248 °F)
4
-25 - 60 °C (-13 - 140 °F)
-55 - 70 °C (-67 - 158 °F)
60 bar (870 psi)
A
B
C
D
36.95
1.45
110
4.33
ISO 228/1 G 1/2
7/16 - 20 UNF
0.25" flare
Output signals
- Signal cut off
Power consumption
Load impedance
Output signals
12.5 - 30 VDC
4-20 mA
21 mA
Max. 660 mW
30 m (98 ft)
P max
Fig. 95
TM063358 5214
Output signals
- Signal cut off
Power consumption
Load impedance
16.6 - 30 VDC
0-10 VDC
11 VDC
Max. 300 mW
Min. 10 kΩ
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Sensor housing
Wetted materials
EPDM or FKM
EPDM or FKM
Enclosure class
Temperature cycling
0
0
Fig. 96
P max
T max
IP67
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
TM063359 5214
10V
sensor
31
4
DPI V.2, 0 - 16.0 bar (0 - 232.1 psi)
Specifications
TM04 9239 3510
Pressure
Fig. 97
Dimensions [mm]
Measuring range
(32-176 °F)
Accuracy (± 1σ), -30 - 100 °C
(8.6 - 284 °F)
Response time
Resolution
0 - 16.0 bar (0 - 232.1 psi)
± 2.5 % FS
± 3 % FS
< 100 ms
(typical 50 ms)
1/1000 FS
(32-176 °F)
(32-212 °F)
electronics
Resolution
0-100 °C (32-212 °F)
±1K
±2K
< 100 ms
(typical 50 ms)
0.1 K
B
Medium types
TM04 9238 0415
D
C
A
Fig. 98
mm
in
Medium temperature
(operation)
(operation)
Storage temperature
Humidity
-30 - 120 °C (-22 - 248 °F)
-25 - 60 °C (-13 - 140 °F)
-55 - 70 °C (-67 - 158 °F)
60 bar (870 psi)
A
B
C
D
36.95
1.45
110
4.33
ISO 228/1 G 1/2
7/16 - 20 UNF
0.25" flare
Output signals
- Signal cut off
Power consumption
Load impedance
Output signals
12.5 - 30 VDC
4-20 mA
21 mA
Max. 660 mW
30 m (98 ft)
P max
Fig. 99
TM063358 5214
Output signals
- Signal cut off
Power consumption
Load impedance
16.6 - 30 VDC
0-10 VDC
11 VDC
Max. 300 mW
Min. 10 kΩ
30 m (98 ft)
Sensor materials
Sensing element
O-ring
Sensor housing
Wetted materials
EPDM or FKM
EPDM or FKM
Enclosure class
Temperature cycling
0
0
P max
T max
TM063359 5214
10V
Fig. 100 Pressure and temperature response of DPI V.2+T
sensor
32
IP67
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
5
RPS, general data
Relative-Pressure sensor, Standard (RPS)
5. Relative-Pressure sensor, Standard (RPS)
TM061286 2214 TM061287 2214
Approvals
Fig. 101 RPS sensor
• WRAS
• KTW
• ACS.
Certificates
75
+
CE
C, CSA, US
C-Tick
Technical overview
The RPS sensor is a combined pressure and
temperature sensor (two-in-one solution) from
Grundfos Direct Sensors™.
The RPS sensors are fully compatible with wet,
1
4
TM05 2253 4711
V
Pipe system
PE
Fig. 102 Electrical connections
water utility
water monitoring
HVAC systems
chiller systems
micro CHP
heat pumps
Pin
Description
Colour
1
Temperature signal (0.5 to 3.5 V relative to pin 3)
Yellow
2
Pressure signal (0.5 to 3.5 V relative to pin 3)
White
3
GND (0 V)
Green
4
Voltage supply (+5 VDC), PELV
Brown
Power supply requirements
• Wide temperature measuring range: 0-100 °C (32212 °F)
• compact design
[bars]
[psi]
0 - 0.6
0 - 1.0
0 - 1.6
0 - 2.5
0 - 4.0
0 - 6.0
0 - 10.0
0 - 8.7
0 - 14.5
0 - 23.2
0 - 36.3
0 - 58.0
0 - 87.0
0 - 145.0
Benefits
output signal
medium)
• 5 VDC
• separated from hazardous live circuitry by double or
reinforced insulation
• power limitation of 150 VA; current limitation of 8 A.
Options
B
A
TM03 8139 0607 TM61287 2214
Features
Pressure ranges
3
V
Applications
•
•
•
•
•
•
•
•
•
2
Fig. 103 sensor options
Pos.
A
B
Description
1/2'' nipple, stainless steel (316L)
Cable connection: Overmoulded (left)
Cable connection: Snap-on (right)
33
5
RPS, 0 - 0.6 bar (0 - 8.7 psi)
Specifications
Pressure
Measuring range
(77-176 °F)
(32-212 °F)
Response time
Resolution
0 - 0.6 bar (0 - 8.7 psi)
± 2 % FS
± 3 % FS
< 0.5 s
5 mbar (0.07 psi)
TM061287 2214
Temperature
Fig. 104 RPS sensor
±1K
±2K
< 1.5 s
0.5 K
Liquids
0-100 °C (32-212 °F)
-25 - 120 °C (-13 - 248 °F),
non-freezing
-25 - 60 °C (-13 - 140 °F)
-55 - 90 °C (-67 - 194 °F)
30 bar (435 psi)
C
Electrical data
TM054669 2512
B
Power supply
A
F
G
A
B
C
D
E
F
G
4.5
0.18
53.7
2.11
27
1.06
20
0.79
39.9
1.57
10.2
0.40
14.8
0.58
Pressure signal
Temperature signal
Power consumption
Load impedance
Wetted materials
Enclosure class
Temperature cycling
TM063353 5214
[V]
Fig. 106 Pressure and temperature response of RPS
sensor
EPDM
Composite (PPS)
Corrosion-resistant coating, EPDM,
FKM, PPS
Output signals
P max
T max
5 VDC (± 5 %), PELV
Grounding of sensor supply
recommended.
0.5 - 3.5 V
0.5 - 3.5 V
< 50 mW
> 10 kΩ
3 m (9.8 ft)
Sensor materials
Sensor
Seal (sensor to housing)
Housing
Fig. 105 Dimensions of RPS sensor
34
Media
Medium temperature
(operation)
(operation)
Ambient air temperature (peak)
Humidity
E
D
0-100 °C (32-212 °F)
Dimensions [mm]
mm
in
Measuring range
(77-176 °F)
(32-212 °F)
Response time
Resolution
IP44
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
RPS, 0 - 1.0 bar (0 - 14.5 psi)
Specifications
Pressure
Measuring range
(77-176 °F)
(32-212 °F)
Response time
Resolution
0 - 1.0 bar (0 - 14.5 psi)
± 2 % FS
± 3 % FS
< 0.5 s
5 mbar (0.07 psi)
TM061287 2214
Temperature
Fig. 107 RPS sensor
Media
Medium temperature
(operation)
(operation)
Humidity
E
D
0-100 °C (32-212 °F)
±1K
±2K
< 1.5 s
0.5 K
Dimensions [mm]
Liquids
0-100 °C (32-212 °F)
-25 - 120 °C (-13 - 248 °F),
non-freezing
-25 - 60 °C (-13 - 140 °F)
-55 - 90 °C (-67 - 194 °F)
30 bar (435 psi)
C
Electrical data
TM054669 2512
B
Power supply
A
F
G
A
B
C
D
E
F
G
4.5
0.18
53.7
2.11
27
1.06
20
0.79
39.9
1.57
10.2
0.40
14.8
0.58
Pressure signal
Temperature signal
Power consumption
Load impedance
Wetted materials
EPDM
Composite (PPS)
FKM, PPS
Enclosure class
Temperature cycling
Output signals
IP44
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
TM063353 5214
[V]
P max
T max
5 VDC (± 5 %), PELV
recommended.
0.5 - 3.5 V
0.5 - 3.5 V
< 50 mW
> 10 kΩ
3 m (9.8 ft)
Sensor materials
Sensor
Housing
mm
in
Measuring range
(77-176 °F)
(32-212 °F)
Response time
Resolution
5
sensor
35
5
RPS, 0 - 1.6 bar (0 - 23.2 psi)
Specifications
Pressure
Measuring range
(77-176 °F)
(32-212 °F)
Response time
Resolution
0 - 1.6 bar (0 - 23.2 psi)
± 1.5 % FS
± 2.5 % FS
< 0.5 s
5 mbar (0.07 psi)
TM061287 2214
Temperature
Fig. 110 RPS sensor
±1K
±2K
< 1.5 s
0.5 K
Liquids
0-100 °C (32-212 °F)
-25 - 120 °C (-13 - 248 °F),
non-freezing
-25 - 60 °C (-13 - 140 °F)
-55 - 90 °C (-67 - 194 °F)
30 bar (435 psi)
C
Electrical data
TM054669 2512
B
Power supply
A
F
G
A
B
C
D
E
F
G
4.5
0.18
53.7
2.11
27
1.06
20
0.79
39.9
1.57
10.2
0.40
14.8
0.58
Pressure signal
Temperature signal
Power consumption
Load impedance
Wetted materials
Enclosure class
Temperature cycling
TM063353 5214
[V]
sensor
EPDM
Composite (PPS)
FKM, PPS
Output signals
P max
T max
5 VDC (± 5 %), PELV
recommended.
0.5 - 3.5 V
0.5 - 3.5 V
< 50 mW
> 10 kΩ
3 m (9.8 ft)
Sensor materials
Sensor
Housing
36
Media
Medium temperature
(operation)
(operation)
Humidity
E
D
0-100 °C (32-212 °F)
Dimensions [mm]
mm
in
Measuring range
(77-176 °F)
(32-212 °F)
Response time
Resolution
IP44
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
RPS, 0 - 2.5 bar (0 - 36.3 psi)
Specifications
Pressure
Measuring range
(77-176 °F)
(32-212 °F)
Response time
Resolution
0 - 2.5 bar (0 - 36.3 psi)
± 1.5 % FS
± 2 % FS
< 0.5 s
20 mbar (0.29 psi)
TM061287 2214
Temperature
Fig. 113 RPS sensor
Media
Medium temperature
(operation)
(operation)
Humidity
E
D
0-100 °C (32-212 °F)
±1K
± 2.5 K
< 1.5 s
0.5 K
Dimensions [mm]
Liquids
0-100 °C (32-212 °F)
-25 - 120 °C (-13 - 248 °F),
non-freezing
-25 - 60 °C (-13 - 140 °F)
-55 - 90 °C (-67 - 194 °F)
30 bar (435 psi)
C
Electrical data
TM054669 2512
B
Power supply
A
F
G
A
B
C
D
E
F
G
4.5
0.18
53.7
2.11
27
1.06
20
0.79
39.9
1.57
10.2
0.40
14.8
0.58
Pressure signal
Temperature signal
Power consumption
Load impedance
Wetted materials
EPDM
Composite (PPS)
FKM, PPS
Enclosure class
Temperature cycling
Output signals
IP44
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
TM063353 5214
[V]
P max
T max
5 VDC (± 5 %), PELV
recommended.
0.5 - 3.5 V
0.5 - 3.5 V
< 50 mW
> 10 kΩ
3 m (9.8 ft)
Sensor materials
Sensor
Housing
mm
in
Measuring range
(77-176 °F)
(32-212 °F)
Response time
Resolution
5
sensor
37
5
RPS, 0 - 4.0 bar (0 - 58.0 psi)
Specifications
Pressure
Measuring range
(77-176 °F)
(32-212 °F)
Response time
Resolution
0 - 4.0 bar (0 - 58.0 psi)
± 2 % FS
± 2.5 % FS
< 0.5 s
20 mbar (0.29 psi)
TM061287 2214
Temperature
Fig. 116 RPS sensor
±1K
±2K
< 1.5 s
0.5 K
Liquids
0-100 °C (32-212 °F)
-25 - 120 °C (-13 - 248 °F),
non-freezing
-25 - 60 °C (-13 - 140 °F)
-55 - 90 °C (-67 - 194 °F)
30 bar (435 psi)
C
Electrical data
TM054669 2512
B
Power supply
A
F
G
A
B
C
D
E
F
G
4.5
0.18
53.7
2.11
27
1.06
20
0.79
39.9
1.57
10.2
0.40
14.8
0.58
Pressure signal
Temperature signal
Power consumption
Load impedance
Wetted materials
Enclosure class
Temperature cycling
TM063353 5214
[V]
sensor
EPDM
Composite (PPS)
FKM, PPS
Output signals
P max
T max
5 VDC (± 5 %), PELV
recommended.
0.5 - 3.5 V
0.5 - 3.5 V
< 50 mW
> 10 kΩ
3 m (9.8 ft)
Sensor materials
Sensor
Housing
38
Media
Medium temperature
(operation)
(operation)
Humidity
E
D
0-100 °C (32-212 °F)
Dimensions [mm]
mm
in
Measuring range
(77-176 °F)
(32-212 °F)
Response time
Resolution
IP44
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
RPS, 0 - 6.0 bar (0 - 87.0 psi)
Specifications
Pressure
Measuring range
(77-176 °F)
(32-212 °F)
Response time
Resolution
0 - 6.0 bar (0 - 87.0 psi)
± 2 % FS
± 2.5 % FS
< 0.5 s
20 mbar (0.29 psi)
TM061287 2214
Temperature
Fig. 119 RPS sensor
Media
Medium temperature
(operation)
(operation)
Humidity
E
D
0-100 °C (32-212 °F)
±1K
± 2.5 K
< 1.5 s
0.5 K
Dimensions [mm]
Liquids
0-100 °C (32-212 °F)
-25 - 120 °C (-13 - 248 °F),
non-freezing
-25 - 60 °C (-13 - 140 °F)
-55 - 90 °C (-67 - 194 °F)
30 bar (435 psi)
C
Electrical data
TM054669 2512
B
Power supply
A
F
G
A
B
C
D
E
F
G
4.5
0.18
53.7
2.11
27
1.06
20
0.79
39.9
1.57
10.2
0.40
14.8
0.58
Pressure signal
Temperature signal
Power consumption
Load impedance
Wetted materials
EPDM
Composite (PPS)
FKM, PPS
Enclosure class
Temperature cycling
Output signals
IP44
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
TM063353 5214
[V]
P max
T max
5 VDC (± 5 %), PELV
recommended.
0.5 - 3.5 V
0.5 - 3.5 V
< 50 mW
> 10 kΩ
3 m (9.8 ft)
Sensor materials
Sensor
Housing
mm
in
Measuring range
(77-176 °F)
(32-212 °F)
Response time
Resolution
5
sensor
39
5
RPS, 0 - 10.0 bar (0 - 145.0 psi)
Specifications
Pressure
Measuring range
(77-176 °F)
(32-212 °F)
Response time
Resolution
0 - 10.0 bar (0 - 145.0 psi)
± 2 % FS
± 2.5 % FS
< 1.0 / 1.5 s
20 mbar (0.29 psi)
TM061287 2214
Temperature
Fig. 122 RPS sensor
±1K
± 2.5 K
< 1.5 s
0.5 K
Liquids
0-100 °C (32-212 °F)
-25 - 120 °C (-13 - 248 °F),
non-freezing
-25 - 60 °C (-13 - 140 °F)
-55 - 90 °C (-67 - 194 °F)
30 bar (435 psi)
C
Electrical data
TM054669 2512
B
Power supply
A
F
G
A
B
C
D
E
F
G
4.5
0.18
53.7
2.11
27
1.06
20
0.79
39.9
1.57
10.2
0.40
14.8
0.58
Pressure signal
Temperature signal
Power consumption
Load impedance
Wetted materials
Enclosure class
Temperature cycling
TM063353 5214
[V]
sensor
EPDM
Composite (PPS)
FKM, PPS
Output signals
P max
T max
5 VDC (± 5 %), PELV
recommended.
0.5 - 3.5 V
0.5 - 3.5 V
< 50 mW
> 10 kΩ
3 m (9.8 ft)
Sensor materials
Sensor
Housing
40
Media
Medium temperature
(operation)
(operation)
Humidity
E
D
0-100 °C (32-212 °F)
Dimensions [mm]
mm
in
Measuring range
(77-176 °F)
(32-212 °F)
Response time
Resolution
IP44
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
6. Differential-Pressure sensor, Standard (DPS)
DPS, general data
Benefits
TM06 1682 2614
output signal
medium)
Fig. 125 DPS sensor
Approvals
• WRAS
• KTW
• ACS.
Differential-Pressure sensor, Standard (DPS)
6
Certificates
Technical overview
The DPS sensor is a combined differential-pressure
and temperature sensor (two-in-one solution) from
Grundfos Direct Sensors™.
The DPS sensors are fully compatible with wet,
C, CSA, US
1
water utility
water monitoring
HVAC systems
chiller systems
micro CHP
heat pumps
Pressure ranges
-
0.6
1.0
1.6
2.5
4.0
6.0
3
4
TM05 2253 4711
V
Pipe system
PE
Fig. 126 Electrical connections
Pin
• Wide temperature measuring range: 0-100 °C (32212 °C)
• compact design
[bars]
2
V
Features
0
0
0
0
0
0
C-Tick
Applications
•
•
•
•
•
•
•
•
•
75
+
CE
[psi]
0 - 8.7
0 - 14.5
0 - 23.2
0 - 36.3
0 - 58.0
0 - 87.0
Description
Colour
1
Temperature signal (0.5 to 4.5 V relative to pin 3)
Yellow
2
Pressure signal (0.5 to 4.5 V relative to pin 3)
White
3
GND (0 V)
Green
4
Voltage supply (+5 VDC), PELV
Brown
Power supply requirements
• 5 VDC
• separated from hazardous live circuitry by double or
reinforced insulation
• power limitation of 150 VA; current limitation of 8 A.
Options
Part
Housing for DPS
Fitting 6 mm (0.23")
AISI 316
Wall bracket (housing for DPS)
Tube connection
Compression fitting
41
6
DPS, 0 - 0.6 bar (0 - 8.7 psi)
Specifications
Pressure
Measuring range
Accuracy (± 1σ),
25-80 °C (77-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
Response time
System pressure
deviation
Resolution
0 - 0.6 bar (0 - 8.7 psi)
± 2 % FS
± 3.0 % FS
< 0.5 s
6 mbar/bar (0.09 psi/psi)
1.2 mbar (0.02 psi)
TM06 1682 2614
Temperature
Fig. 127 DPS sensor
Dimensions [mm]
0-100 °C (32-212 °F)
±1K
±2K
< 1.0 s
0.2 K
A
Media
Medium temperature
(operation)
Medium temperature
(peak)
Ambient air temp.
(operation)
Ambient air temp. (peak)
Humidity (relative)
B
D
System pressure, p1
TM063455 0115
G
2xH
F
C
E
mm
in
Measuring range
Accuracy (± 1σ),
25-80 °C (77-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
Response time, sensing
element to output
change
Resolution
A
B
C
D
E
F
G
H
20
0.79
29.9
1.18
40
1.57
39.9
1.57
35
1.38
32.9
1.30
57.9
2.28
1/8 - 27
NPT
Output signals
Differential pressure,
p 1 - p2
Burst pressure, p1
Burst pressure, p2
Liquids
0-100 °C (32-212 °F)
-25 - 120 °C (-13 - 248 °F),
non-freezing
-25 - 60 °C (-13 - 140 °F)
-55 - 90 °C (-67 - 194 °F)
0-95 %, non-condensing
Max. 16 bar at 70 °C (232 psi at 158 °F)
Max. 10 bar (145 psi)
Electrical data
Power supply
Output signals
Pressure signal
Temperature signal
Power consumption
Load impedance
5 VDC (± 5 %), PELV.
Grounding of sensor supply required.
Ratiometric
0.5 - 4.5 V
0.5 - 4.5 V
< 50 mW
> 10 kΩ
3 m (9.8 ft)
Sensor materials
[V]
Sensing element
Sealing cap
Housing
Wetted materials
EPDM
Composite (PPS)
Corrosion-resistant coating, EPDM, FKM,
PPS
0
P max
T max
TM063357 5214
Fig. 128 Differential-pressure and temperature response
of DPS sensor
42
Enclosure class
Temperature cycling
Vibration (nondestructive)
Electromagnetic
compatibility
IP44
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
DPS, 0 - 1.0 bar (0 - 14.5 psi)
Specifications
Pressure
Measuring range
Accuracy (± 1σ),
25-80 °C (77-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
Response time
System pressure
deviation
Resolution
0 - 1.0 bar (0 - 14.5 psi)
± 2 % FS
± 3.0 % FS
< 0.5 s
1.3 mbar (0.02 psi)
TM06 1682 2614
Temperature
Fig. 129 DPS sensor
Dimensions [mm]
0-100 °C (32-212 °F)
±1K
±2K
< 1.0 s
0.2 K
A
Media
Medium temperature
(operation)
Medium temperature
(peak)
Ambient air temp.
(operation)
Humidity (relative)
B
D
System pressure, p1
TM063455 0115
G
2xH
F
C
E
mm
in
Measuring range
Accuracy (± 1σ),
25-80 °C (77-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
element to output
change
Resolution
A
B
C
D
E
F
G
H
20
0.79
29.9
1.18
40
1.57
39.9
1.57
35
1.38
32.9
1.30
57.9
2.28
1/8 - 27
NPT
Output signals
p1 - p2
Burst pressure, p1
Burst pressure, p2
6
Liquids
0-100 °C (32-212 °F)
-25 - 120 °C (-13 - 248 °F),
non-freezing
-25 - 60 °C (-13 - 140 °F)
-55 - 90 °C (-67 - 194 °F)
Electrical data
Power supply
Output signals
Pressure signal
Temperature signal
Power consumption
Load impedance
5 VDC (± 5 %), PELV.
Ratiometric
0.5 - 4.5 V
0.5 - 4.5 V
< 50 mW
> 10 kΩ
3 m (9.8 ft)
Sensor materials
[V]
Sensing element
Sealing cap
Housing
Wetted materials
EPDM
Composite (PPS)
PPS
0
P max
T max
TM063357 5214
Enclosure class
Temperature cycling
Electromagnetic
compatibility
IP44
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
of DPS sensor
43
6
DPS, 0 - 1.6 bar (0 - 23.2 psi)
Specifications
Pressure
Measuring range
Accuracy (± 1σ),
25-80 °C (77-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
Response time
System pressure
deviation
Resolution
0 - 1.6 bar (0 - 23.2 psi)
± 2 % FS
± 2.5 % FS
< 0.5 s
1.6 mbar (0.023 psi)
TM06 1682 2614
Temperature
Fig. 131 DPS sensor
Dimensions [mm]
0-100 °C (32-212 °F)
±1K
±2K
< 1.0 s
0.2 K
A
Media
Medium temperature
(operation)
Medium temperature
(peak)
Ambient air temp.
(operation)
Humidity (relative)
B
D
System pressure, p1
TM063455 0115
G
2xH
F
C
E
mm
in
Measuring range
Accuracy (± 1σ),
25-80 °C (77-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
element to output
change
Resolution
A
B
C
D
E
F
G
H
20
0.79
29.9
1.18
40
1.57
39.9
1.57
35
1.38
32.9
1.30
57.9
2.28
1/8 - 27
NPT
Output signals
p1 - p2
Burst pressure, p1
Burst pressure, p2
Liquids
0-100 °C (32-212 °F)
-25 - 120 °C (-13 - 248 °F),
non-freezing
-25 - 60 °C (-13 - 140 °F)
-55 - 90 °C (-67 - 194 °F)
Electrical data
Power supply
Output signals
Pressure signal
Temperature signal
Power consumption
Load impedance
5 VDC (± 5 %), PELV.
Ratiometric
0.5 - 4.5 V
0.5 - 4.5 V
< 50 mW
> 10 kΩ
3 m (9.8 ft)
Sensor materials
[V]
Sensing element
Sealing cap
Housing
Wetted materials
EPDM
Composite (PPS)
PPS
0
P max
T max
TM063357 5214
of DPS sensor
44
Enclosure class
Temperature cycling
Electromagnetic
compatibility
IP44
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
DPS, 0 - 2.5 bar (0 - 36.3 psi)
Specifications
Pressure
Measuring range
Accuracy (± 1σ),
25-80 °C (77-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
Response time
System pressure
deviation
Resolution
0 - 2.5 bar (0 - 36.3 psi)
± 2 % FS
± 2.5 % FS
< 0.5 s
2.5 mbar (0.07 psi)
TM06 1682 2614
Temperature
Fig. 133 DPS sensor
Dimensions [mm]
0-100 °C (32-212 °F)
±1K
±2K
< 1.0 s
0.2 K
A
Media
Medium temperature
(operation)
Medium temperature
(peak)
Ambient air temp.
(operation)
Humidity (relative)
B
D
System pressure, p1
TM063455 0115
G
2xH
F
C
E
mm
in
Measuring range
Accuracy (± 1σ),
25-80 °C (77-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
element to output
change
Resolution
A
B
C
D
E
F
G
H
20
0.79
29.9
1.18
40
1.57
39.9
1.57
35
1.38
32.9
1.30
57.9
2.28
1/8 - 27
NPT
Output signals
p1 - p2
Burst pressure, p1
Burst pressure, p2
6
Liquids
0-100 °C (32-212 °F)
-25 - 120 °C (-13 - 248 °F),
non-freezing
-25 - 60 °C (-13 - 140 °F)
-55 - 90 °C (-67 - 194 °F)
Electrical data
Power supply
Output signals
Pressure signal
Temperature signal
Power consumption
Load impedance
5 VDC (± 5 %), PELV.
Ratiometric
0.5 - 4.5 V
0.5 - 4.5 V
< 50 mW
> 10 kΩ
3 m (9.8 ft)
Sensor materials
[V]
Sensing element
Sealing cap
Housing
Wetted materials
EPDM
Composite (PPS)
PPS
0
P max
T max
TM063357 5214
Enclosure class
Temperature cycling
Electromagnetic
compatibility
IP44
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
of DPS sensor
45
6
DPS, 0 - 4.0 bar (0 - 58.0 psi)
Specifications
Pressure
Measuring range
Accuracy (± 1σ),
25-80 °C (77-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
Response time
System pressure
deviation
Resolution
0 - 4.0 bar (0 - 58.0 psi)
± 2 % FS
± 2.5 % FS
< 0.5 s
4.0 mbar (0.06 psi)
TM06 1682 2614
Temperature
Fig. 135 DPS sensor
Dimensions [mm]
0-100 °C (32-212 °F)
±1K
±2K
< 1.0 s
0.2 K
A
Media
Medium temperature
(operation)
Medium temperature
(peak)
Ambient air temp.
(operation)
Humidity (relative)
B
D
System pressure, p1
TM063455 0115
G
2xH
F
C
E
mm
in
Measuring range
Accuracy (± 1σ),
25-80 °C (77-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
element to output
change
Resolution
A
B
C
D
E
F
G
H
20
0.79
29.9
1.18
40
1.57
39.9
1.57
35
1.38
32.9
1.30
57.9
2.28
1/8 - 27
NPT
Output signals
p1 - p2
Burst pressure, p1
Burst pressure, p2
Liquids
0-100 °C (32-212 °F)
-25 - 120 °C (-13 - 248 °F),
non-freezing
-25 - 60 °C (-13 - 140 °F)
-55 - 90 °C (-67 - 194 °F)
Electrical data
Power supply
Output signals
Pressure signal
Temperature signal
Power consumption
Load impedance
5 VDC (± 5 %), PELV.
Ratiometric
0.5 - 4.5 V
0.5 - 4.5 V
< 50 mW
> 10 kΩ
3 m (9.8 ft)
Sensor materials
[V]
Sensing element
Sealing cap
Housing
Wetted materials
EPDM
Composite (PPS)
PPS
0
P max
T max
TM063357 5214
of DPS sensor
46
Enclosure class
Temperature cycling
Electromagnetic
compatibility
IP44
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
DPS, 0 - 6.0 bar (0 - 87.0 psi)
Specifications
Pressure
Measuring range
Accuracy (± 1σ),
25-80 °C (77-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
Response time
System pressure
deviation
Resolution
0 - 6.0 bar (0 - 87.0 psi)
± 2 % FS
± 2.5 % FS
< 0.5 s
6.0 mbar (0.09 psi)
TM06 1682 2614
Temperature
Fig. 137 DPS sensor
Dimensions [mm]
0-100 °C (32-212 °F)
±1K
±2K
< 1.0 s
0.2 K
A
Media
Medium temperature
(operation)
Medium temperature
(peak)
Ambient air temp.
(operation)
Humidity (relative)
B
D
System pressure, p1
TM063455 0115
G
2xH
F
C
E
mm
in
Measuring range
Accuracy (± 1σ),
25-80 °C (77-176 °F)
Accuracy (± 1σ),
0-100 °C (32-212 °F)
element to output
change
Resolution
A
B
C
D
E
F
G
H
20
0.79
29.9
1.18
40
1.57
39.9
1.57
35
1.38
32.9
1.30
57.9
2.28
1/8 - 27
NPT
Output signals
p1 - p2
Burst pressure, p1
Burst pressure, p2
6
Liquids.
0-100 °C
-25 - 120 °C (-13 - 248 °F),
non-freezing
-25 - 60 °C (-13 - 140 °F)
-55 - 90 °C (-67 - 194 °F)
Electrical data
Power supply
Output signals
Pressure signal
Temperature signal
Power consumption
Load impedance
5 VDC (± 5 %), PELV.
Ratiometric
0.5 - 4.5 V
0.5 - 4.5 V
< 50 mW
> 10 kΩ
3 m (9.8 ft)
Sensor materials
[V]
Sensing element
Sealing cap
Housing
Wetted materials
EPDM
Composite (PPS)
PPS
0
P max
T max
TM063357 5214
Enclosure class
Temperature cycling
Electromagnetic
compatibility
IP44
IEC 68-2-14
20-2000 Hz, 10G, 4 h
EN 61326-1
of DPS sensor
47
7
Product range
7. Product range
RPI sensor
Scope of delivery:
• RPI sensor
• 2 m cable (6.5 ft)
• quick guide.
Complete product range
RPI-••0-0.6b-1-C-N••••••-EG6-••-•••-•W•1
RPI-••0-0.6b-1-C-N••••••-VG6-••-•••-•W•1
RPI-••0-0.6b-1-F-N••••••-EG6-••-•••-•W•1
RPI-••0-0.6b-1-F-N••••••-VG6-••-•••-•W•1
RPI-••0-1.0b-1-C-N••••••-EG6-••-•••-•W•1
RPI-••0-1.0b-1-C-N••••••-VG6-••-•••-•W•1
RPI-••0-1.0b-1-F-N••••••-EG6-••-•••-•W•1
RPI-••0-1.0b-1-F-N••••••-VG6-••-•••-•W•1
RPI-••0-1.6b-1-C-N••••••-EG6-••-•••-•W•1
RPI-••0-1.6b-1-C-N••••••-VG6-••-•••-•W•1
RPI-••0-1.6b-1-F-N••••••-EG6-••-•••-•W•1
RPI-••0-1.6b-1-F-N••••••-VG6-••-•••-•W•1
RPI-••0-2.5b-1-C-N••••••-EG6-••-•••-•W•1
RPI-••0-2.5b-1-C-N••••••-VG6-••-•••-•W•1
RPI-••0-2.5b-1-F-N••••••-EG6-••-•••-•W•1
RPI-••0-2.5b-1-F-N••••••-VG6-••-•••-•W•1
RPI-••0-4.0b-1-C-N••••••-EG6-••-•••-•W•1
RPI-••0-4.0b-1-C-N••••••-VG6-••-•••-•W•1
RPI-••0-4.0b-1-F-N••••••-EG6-••-•••-•W•1
RPI-••0-4.0b-1-F-N••••••-VG6-••-•••-•W•1
RPI-••0-6.0b-1-C-N••••••-EG6-••-•••-•W•1
RPI-••0-6.0b-1-C-N••••••-VG6-••-•••-•W•1
RPI-••0-6.0b-1-F-N••••••-EG6-••-•••-•W•1
RPI-••0-6.0b-1-F-N••••••-VG6-••-•••-•W•1
RPI-•••0-10b-1-C-N••••••-EG6-••-•••-•W•1
RPI-•••0-10b-1-C-N••••••-VG6-••-•••-•W•1
RPI-•••0-10b-1-F-N••••••-EG6-••-•••-•W•1
RPI-•••0-10b-1-F-N••••••-VG6-••-•••-•W•1
RPI-•••0-16b-1-C-N••••••-EG6-••-•••-•W•1
RPI-•••0-16b-1-C-N••••••-VG6-••-•••-•W•1
RPI-•••0-16b-1-F-N••••••-EG6-••-•••-•W•1
RPI-•••0-16b-1-F-N••••••-VG6-••-•••-•W•1
RPI-•••0-25b-1-C-N••••••-EG6-••-•••-•W•1
RPI-•••0-25b-1-C-N••••••-VG6-••-•••-•W•1
RPI-•••0-25b-1-F-N••••••-EG6-••-•••-•W•1
RPI-•••0-25b-1-F-N••••••-VG6-••-•••-•W•1
48
Pressure range
Thread
Temperature
measurement
O-ring
Product number
EPDM
FKM
●
0 - 0.6 bar
(0 - 8.7 psi)
G 1/2
●
●
●
●
●
●
0 - 1.0 bar
(0 - 14.5 psi)
G 1/2
●
●
●
●
●
●
0 - 1.6 bar
(0 - 23.2 psi)
G 1/2
●
●
●
●
●
●
0 - 2.5 bar
(0 - 36.3 psi)
G 1/2
●
●
●
●
●
●
0 - 4.0 bar
(0 - 58.0 psi)
G 1/2
●
●
●
●
●
●
0 - 6.0 bar
(0 - 87.0 psi)
G 1/2
●
●
●
●
●
●
0 - 10.0 bar
(0 - 145.0 psi)
G 1/2
●
●
●
●
●
●
0 - 16.0 bar
(0 - 232.1 psi)
G 1/2
●
●
●
●
●
●
0 - 25.0 bar
(0 - 362.6 psi)
G 1/2
●
●
●
●
●
97748907
97748948
97748926
97748957
97748908
97748949
97748928
97748958
97748909
97748950
97748929
97748959
97748910
97748951
97748930
97748960
97748921
97748952
97748941
97748961
97748922
97748953
97748942
97748962
97748923
97748954
97748944
97748963
97748924
97748955
97748945
97748964
97748925
97748956
97748946
97748965
7
Product range
DPI V.2 sensor
Scope of delivery:
• DPI V.2 sensor
• 2 m cable (6.5 ft)
• capillary tube with fitting
• quick guide.
Complete product range
DPI-••0-0.6b-2-C-M2.000X-EG6-••-•••-SW•1
DPI-••0-0.6b-2-C-M2.000X-VG6-••-•••-SW•1
DPI-••0-0.6b-2-F-M2.000X-EG6-••-•••-SW•1
DPI-••0-0.6b-2-F-M2.000X-VG6-••-•••-SW•1
DPI-••0-1.0b-2-C-M2.000X-EG6-••-•••-SW•1
DPI-••0-1.0b-2-C-M2.000X-VG6-••-•••-SW•1
DPI-••0-1.0b-2-F-M2.000X-EG6-••-•••-SW•1
DPI-••0-1.0b-2-F-M2.000X-VG6-••-•••-SW•1
DPI-••0-1.6b-2-C-M2.000X-EG6-••-•••-SW•1
DPI-••0-1.6b-2-C-M2.000X-VG6-••-•••-SW•1
DPI-••0-1.6b-2-F-M2.000X-EG6-••-•••-SW•1
DPI-••0-1.6b-2-F-M2.000X-VG6-••-•••-SW•1
DPI-••0-2.5b-2-C-M2.000X-EG6-••-•••-SW•1
DPI-••0-2.5b-2-C-M2.000X-VG6-••-•••-SW•1
DPI-••0-2.5b-2-F-M2.000X-EG6-••-•••-SW•1
DPI-••0-2.5b-2-F-M2.000X-VG6-••-•••-SW•1
DPI-••0-4.0b-2-C-M2.000X-EG6-••-•••-SW•1
DPI-••0-4.0b-2-C-M2.000X-VG6-••-•••-SW•1
DPI-••0-4.0b-2-F-M2.000X-EG6-••-•••-SW•1
DPI-••0-4.0b-2-F-M2.000X-VG6-••-•••-SW•1
DPI-••0-6.0b-2-C-M2.000X-EG6-••-•••-SW•1
DPI-••0-6.0b-2-C-M2.000X-VG6-••-•••-SW•1
DPI-••0-6.0b-2-F-M2.000X-EG6-••-•••-SW•1
DPI-••0-6.0b-2-F-M2.000X-VG6-••-•••-SW•1
DPI-•••0-10b-2-C-M2.000X-EG6-••-•••-SW•1
DPI-•••0-10b-2-C-M2.000X-VG6-••-•••-SW•1
DPI-•••0-10b-2-F-M2.000X-EG6-••-•••-SW•1
DPI-•••0-10b-2-F-M2.000X-VG6-••-•••-SW•1
DPI-•••0-16b-2-C-M2.000X-EG6-••-•••-SW•1
DPI-•••0-16b-2-C-M2.000X-VG6-••-•••-SW•1
DPI-•••0-16b-2-F-M2.000X-EG6-••-•••-SW•1
DPI-•••0-16b-2-F-M2.000X-VG6-••-•••-SW•1
Pressure range
Thread
Temperature
measurement
O-ring
Product number
EPDM
FKM
●
0 - 0.6 bar
(0 - 8.7 psi)
G 1/2
●
●
●
●
●
●
0 - 1.0 bar
(0 - 14.5 psi)
G 1/2
●
●
●
●
●
●
0 - 1.6 bar
(0 - 23.2 psi)
G 1/2
●
●
●
●
●
●
0 - 2.5 bar
(0 - 36.3 psi)
G 1/2
●
●
●
●
●
●
0 - 4.0 bar
(0 - 58.0 psi)
G 1/2
●
●
●
●
●
●
0 - 6.0 bar
(0 - 87.0 psi)
G 1/2
●
●
●
●
●
●
0 - 10.0 bar
(0 - 145.0 psi)
G 1/2
●
●
●
●
●
●
0 - 16.0 bar
(0 - 232.1 psi)
G 1/2
●
●
●
●
●
97747194
97747215
97747202
97747244
97747195
97747216
97747203
97747245
97747196
97747218
97747204
97747246
97747197
97747219
97747205
97747247
97747198
97747220
97747206
97747249
97747199
97747241
97747207
97747250
97747200
97747242
97747208
97747251
97747201
97747209
97747209
97747252
49
7
Product range
DPI sensor
The DPI sensor is available as a single sensor as well
as in sets with capillary tubes.
As standard, the scope of delivery includes:
• DPI sensor
• cable with bracket
• installation and operating instructions for Grundfos
DPI sensor.
See table below for sets with special parts.
Product description
DPI 0-0.6 Complete
DPI 0-1.0 Complete
DPI 0-1.6 Complete
DPI 0-2.5 Complete
DPI 0-4.0 Complete
DPI 0-6.0 Complete
DPI 0-10.0 Complete
DPI 0-0.6 Set 1
DPI 0-1.0 Set 1
DPI 0-1.6 Set 1
DPI 0-2.5 Set 1
DPI 0-4.0 Set 1
DPI 0-6.0 Set 1
DPI 0-10.0 Set 1
DPI 0-1.2 Set 2
DPI 0-2.5 Set 2
DPI 0-4.0 Set 2Wou
DPI 0-6.0 Set 2
DPI 0-10.0 Set 2
Pressure
range
Cable length
0 - 0.6 bar
(0 - 8.7 psi)
0 - 1.0 bar
(0 - 14.5 psi)
0 - 1.6 bar
(0 - 23.2 psi)
0 - 2.5 bar
(0 - 36.3 psi)
0 - 4.0 bar
(0 - 58.0 psi)
0 - 6.0 bar
(0 - 87.0 psi)
0 - 10.0 bar
(0 - 145.0 psi)
0 - 0.6 bar
(0 - 8.7 psi)
0 - 1.0 bar
(0 - 14.5 psi)
0 - 1.6 bar
(0 - 23.2 psi)
0 - 2.5 bar
(0 - 36.3 psi)
0 - 4.0 bar
(0 - 58.0 psi)
0 - 6.0 bar
(0 - 87.0 psi)
0 - 10.0 bar
(0 - 145.0 psi)
0 - 1.2 bar
(0 - 17.4 psi)
0 - 2.5 bar
(0 - 36.3 psi)
0 - 4.0 bar
(0 - 58.0 psi)
0 - 6.0 bar
(0 - 87.0 psi)
0 - 10.0 bar
(0 - 145.0 psi)
0.9 m
(2.9 ft)
0.9 m
(2.9 ft)
0.9 m
(2.9 ft)
0.9 m
(2.9 ft)
0.9 m
(2.9 ft)
0.9 m
(2.9 ft)
0.9 m
(2.9 ft)
0.9 m
(2.9 ft)
0.9 m
(2.9 ft)
0.9 m
(2.9 ft)
0.9 m
(2.9 ft)
0.9 m
(2.9 ft)
0.9 m
(2.9 ft)
0.9 m
(2.9 ft)
5m
(16.4 ft)
5m
(16.4 ft)
5m
(16.4 ft)
5m
(16.4 ft)
5m
(16.4 ft)
Wall bracket
Capillary
tube
Reducing piece
7/16-20 UNF - R 1/4
Service
instructions
Product
number
●
96561232
●
96573681
●
96573682
●
96573683
●
96573684
●
96573685
●
96573686
●
●
●
●
●
96611522
●
●
●
●
●
96611523
●
●
●
●
●
96611524
●
●
●
●
●
96611525
●
●
●
●
●
96611526
●
●
●
●
●
96611527
●
●
●
●
●
96611550
●
●
●
96760247
●
●
●
96760248
●
●
●
96760249
●
●
●
96760250
●
●
●
96829235
RPS, DPS sensor
Grundfos offers a wide range of custom-built RPS and
DPS sensors.
The RPS and DPS sensors can be customized
depending on the application.
Therefore, please contact Grundfos Direct Sensors
when proceeding to selection.
50
Motor
bracket
8. Accessories
TM04 4194 0809
The sensor interface, type SI 001 PSU, from Grundfos
Direct Sensors™ is an external power supply for the
DPI sensor.
The external power supply must be used where the
distance between the sensor and the controller is
longer than 30 m (98 ft).
Adaptor for mounting in Grundfos
CR pumps
Accessories
8
This adaptor is required when mounting the RPI /
RPI+T or DPI V.2 / DPI V.2 +T on CR pumps.
Grundfos CR pump size
Pump type
1
3
5
10
15
20
32
45
64
90
120
150
CR, CRE
-
-
-
-
❍
❍
❍
●
●
●
●
●
CRI, CRIE
-
-
-
-
❍
❍
●
●
●
●
●
●
CRN, CRNE
-
-
-
-
❍
❍
❍
●
●
●
●
●
- Does not require an adaptor.
❍ Requires an adaptor if the sensor and coupling guard are in direct
contact (will create unnecessary acoustic noise).
● Always requires an adaptor.
Description
Product number
Fig. 139 sensor interface, SI 001 PSU
Specifications:
• Voltage range: 110-400 VAC.
• Frequency: 50-60 Hz.
• Ambient temperature: -20 to +50 °C (-4 to 122 °F).
• Enclosure class: IP54.
Part
Adaptor for RPI / RPI+T and
DPI / DPI+T
98255224
Product number
96915820
M12 cable
4-wire screened cable with M12 connector in sensor
end and open end in equipment end.
Description
Length
Product number
Cable, industry
M2.000X
2 m (6.6 ft)
96841343
Cable, industry
M5.000X
5 m (16.4 ft)
96841344
Capillary tube
The capillary tube is used together with the DPI / DPI
V.2 and DPI+T / DPI V.2 +T to connect the sensor to
the low-pressure side of the equipment.
Description
Capillary tube 7/16 - 20 UNF
Product number
00ID5225
51
8
Accessories
Sensor interface, SI 010 CNV
TM04 4882 2209
The sensor interface, type SI 010 CNV, from Grundfos
Direct Sensors™ is an external power supply, signal
amplifier and signal converter for Grundfos sensors,
standard variants (VFS, RPS, DPS).
SI 010 CNV has built-in precision resistors enabling
the sensor to send 4-20 mA, 1-5 V and 2-10 V output
signals.
SI 010 CNV should be used in applications where
sensors from the standard product range are used, but
the controller requires a 4-20 mA input signal.
Fig. 140 Sensor interface, SI 010 CNV
Specifications:
• Voltage range: 115-230 VAC ± 10 % or 24 VDC.
• Frequency: 50-60 Hz.
• Power consumption: max. 2.5 W.
• Ambient temperature: -20 to +50 °C (-4 to 122 °F).
• Enclosure class: IP20.
Part
Sensor interface, SI 010 CNV, IP20
52
Product number
96983684
9
Appendix
9. Appendix
Installation of RPI, DPI sensor
RPI
P2
P1
Sensor 2
Sensor 1
Pump/sysstem
DPI
(p
(p-)
P1 Sensor
(p+)
P2
Pump/sysstem
!
M12
M12, IP67, UL CCN:
CYJV and CYJV7
>65 °C
(>149 °F)
ISO 228/ 1 – G½
EPDM, FKM
32 mm
20 Nm
d1 = 16.3 mm
d2 = 2.4 mm
d2
Max. 28 bar
(406 PSI)
IP67
-30 to 120 °C
(-22 to 248 °F)
TM05 5857 4112
d1
-25
25 to
60 °C
(-13 to
140 °F)
53
10
Grundfos Product Center
10. Grundfos Product Center
Online search and sizing tool to help you
make the right choice.
http://product-selection.grundfos.com
SIZING enables you to
size a pump based on
entered data and
selection choices.
REPLACEMENT enables you to find a
replacement product.
Search results will include information on
• the lowest purchase price
• the lowest energy consumption
• the lowest total life cycle cost.
CATALOGUE gives you
access to the Grundfos
product catalogue.
LIQUIDS enables you to find pumps
designed for aggressive, flammable
or other special liquids.
All the information you need in one place
Downloads
Performance curves, technical specifications, pictures, dimensional drawings, motor
curves, wiring diagrams, spare parts, service kits, 3D drawings, documents, system parts.
The Product Center displays any recent and saved items - including complete projects right on the main page.
On the product pages, you can download
installation and operating instructions, data
booklets, service instructions, etc. in PDF format.
Subject to alterations.
54
55
ECM: 1155282
GRUNDFOS A/S
DK-8850 Bjerringbro . Denmark
Telephone: +45 87 50 14 00
www.grundfos.com
The name Grundfos, the Grundfos logo, and be think innovate are registered trademarks owned by Grundfos Holding A/S or Grundfos A/S, Denmark. All rights reserved worldwide.
97790251 0315
© Copyright Grundfos Holding A/S

Grundfos Direct Sensor™

Transcription

Similar documents

Accessori: Disegno quotato Campo di misura, tipico LES 36

Copy of GM - STAR EnviroTech Inc.

Accessories: Dimensioned drawing Electrical connection ODSL 96B

Hyundai N100 Inverter Datasheet.