gullco international (uk) limited gullco international (uk

Transcription

F.O.B. OUR PLANT – NEWMARKET – CANADA
OR
EX-WORKS – GULLCO INTERNATIONAL (UK) LIMITED
Prices are those in effect at the date of this price list
And are subject to change without notice
GULLCO INTERNATIONAL (U.K.) LTD.
5 Stonecrop, North Quarry Business Park, Appley Bridge, Lancs. U.K. WN6 9DB
Telephone: +44 (0) 1257 253 579 – Fax: +44 (0)1257 254 629
Email: sales@gullco.co.uk
www.gullco.com
REV: 090201
PRICE LIST - EXPORT
INDEX
DESCRIPTION
INDEX
“KAT” All Position Variable Speed Travel Carriage for Rigid Track ...........................................1
“KAT” Flexible Kat Track System................................................................................................2
“KAT” Travel Carriage / Auto Weld Combination........................................................................3
“KAT” Travel Carriage for Interface with Star-Trac II Gouging Controller ..................................4
Conversion parts - Standard “KAT” to Flexible “KAT”/Flexible “KAT” to a Rigid “KAT”..............5
Gear Trains and Accessories .....................................................................................................6
Transformers...............................................................................................................................6
“KAT” Hydraulic Carriage...........................................................................................................7
“KAT II” All Position Variable Speed Travel Carriage & Accessories .........................................8 - 9
Rack Boxes, Rack Arms 1-1/8” (29 mm) ....................................................................................10
Rack Boxes, Rack Arms 1-1/2” (38 mm) ....................................................................................11
Gun/Torch Holders Rack Box Riser Bracket & Cable Support Assembly ..................................12
Motorized Arms for positioning Welding Guns............................................................................13 - 14
Mechanical Height Sensors & Fillet Weld Seam Tracker ...........................................................15
Track Sections ............................................................................................................................16
Additional Costs for Rolling Track...............................................................................................17
Track Mounting Devices .............................................................................................................18 - 21
Vacuum Equipment.....................................................................................................................22 - 23
Heavy Duty Beam/Bridge Carriage and Track............................................................................24
“KAT” Carriage/Automatic Indexer/Remote Control Indexer ......................................................25 - 26
“KAT” Carriage/Compact Oscillator Combo/Remote Oscillators ................................................27 - 30
“Moggy” Fillet Welding Trackless Carriage.................................................................................31
Magnetic Moggy Fillet Welding Trackless Carriage ...................................................................32
Vertical Overlay Bridge System ..................................................................................................33 - 34
“KAT Tracker” Seam Trackers ....................................................................................................35
“SAM” Heavy Duty Friction Drive Carriage .................................................................................36
Side Beam Carriage....................................................................................................................37
Standard Positioner & Through Hole Positioner .........................................................................38
Positioner Accessories ...............................................................................................................39
Programmable Positioner with Pneumatic Torch Positioning/Accessories ................................40
Self-Centering Grippers ..............................................................................................................41
“Kamel” Pipe Turning Rolls & Torch Supports............................................................................42
Portable Plate Bevelling Machines .............................................................................................43 – 45
Electrode Stabilizing Ovens………………………………………………………………………… 46
Flux Holding Hoppers ………………………………………………………………………………….47
Dry Pak Electrode Dispenser………………………………………………………………………….48
Non-Metallic Weld Backing/Fibre Glass Backing……………………………………………………49
Harris Cutting Torches ................................................................................................................51
Harris Cutting Nozzles ................................................................................................................52
Revision List ..............................................................................................................................53
PRICE LIST - EXPORT
“KAT” ALL POSITION VARIABLE SPEED TRAVEL CARRIAGE FOR RIGID TRACK
USING THE GULLCO 24 VOLT D.C GSP CONTROL
For Operation on either 42/115/230 volts single phase 50/60 Hz A.C. Power Supply –
*Specify Voltage When Placing Order A = 42 V – B = 115 V – C = 230 V
PART NO.
GK-200-RL*
GK-200-RM*
GK-200-RH*
DESCRIPTION
PRICE
“KAT” Variable Speed Travel Carriage for rigid track......................................... $
heavy-duty self-aligning wheel assemblies, closed loop tack feed-back for
accurate speed control when running in any plane, regardless of load.
(Maximum 100 lbs.) (45 kgs). The carriage is controlled by the Gullco low
voltage 24 volt GSP microprocessor pulse width modulation motor control,
interfacing with the forward/stop/reverse switch and infinitely variable 4-turn
speed potentiometer. The LED display is in IPM or cm/min. The motor control
can be upgraded to provide auto forward/reverse, limit switches and auto wire
feed start. Prices shown below.
SPEED RANGES OF “KAT” CARRIAGES
Model GK-200-RL
Model GK-200-RM
Model GK-200-RH
-
0.5 – 16.4 IPM (1.2 TO 41.6 cm/min)
1.0 – 32.7 IPM (2.5 to 83.1 cm/min)
2.7 – 88.4 IPM (6.7 – 224 cm/min)
See Page 6 for High and Low Speed Gear Train Assemblies
GK-171-154
Rigid Track Idler Carriage ...................................................................................... $
Complete with heavy duty self-aligning wheel assemblies providing 8-3/4” x
14-7/8” (222 mm x 378 mm) flat surface for mounting equipment and can be
towed behind a “KAT” Travel Carriage. (complete with a towing kit).
GK-191-P-071
Auxiliary Wire Feed Start Relay Kit .......................................................................
Including relay, circuit board, mounting hardware, multipin connector with 15 ft.
(4572 mm) of wire feed cable. Recommended for all welding applications.
GK-191-P-045
Forward/Reverse Limit Switch Kit .........................................................................
to stop “KAT” Carriage comprising two (2) limit switches mounted on the “KAT”
Carriage complete with wiring, connector and two (2) adjustable track mounted
limit switch actuators to stop Carriage when limit switches are activated.
GSP-2013
Remote Pendant Control Kit .................................................................................. $
Comprising Remote Pendant (no control) attached to 8 ft (2438 mm) control
cable one end and KAT control blanking plate other end with internal
connectors at each end. This remote pendant uses the GSP control removed
from the “KAT” Carriage. This kit can be easily field installed (or factory
installed at no charge.)
GS-474-060
“KAT” Extension Assembly - Front.......................................................................
GS-474-061
“KAT” Extension Assembly - Rear........................................................................
February 1, 2009
-1-
All Prices Canadian Dollars
PRICE LIST - EXPORT
“KAT” ALL POSITION VARIABLE SPEED TRAVEL CARRIAGE FOR FLEXIBLE TRACK
USING THE GULLCO 24 VOLT D.C GSP CONTROL
PART NO.
GK-200-FL*
GK-200-FM*
GK-200-FH*
DESCRIPTION
PRICE
“KAT” Variable Speed Travel Carriage for Flexible Track .................................. $
‘V’-Type self-aligning wheel assemblies with closed loop tack feed-back for
accurate speed control when running in any plane, regardless of load.
(Maximum 100 lbs.) (45 kgs). The carriage is controlled by the Gullco low
feed start. Prices shown below.
SPEED RANGES OF “KAT” CARRIAGES
Model GK-200-FL
Model GK-200-FM
Model GK-200-FH
-
0.8 – 25.8 IPM (2.0 TO 65.4 cm/min)
1.5 – 51.5 IPM (3.9 to 131.0 cm/min)
4.2 – 139.1 IPM 10.6 – 353.0 cm/min)
GK-192-F-154
Flexible Track Idler Carriage ................................................................................. $
Complete with V-Type self-aligning wheel assemblies providing 8-3/4” x 147/8” (222 mm x 378 mm) flat surface for mounting equipment and can be
towed behind a “KAT” Travel Carriage. (complete with a towing kit).
GK-191-P-071
including relay, circuit board, mounting hardware, multipin connector with 15 ft.
GK-192-F-045
limit switch actuators to stop Carriage when limit switches are activated.
GSP-2013
February 1, 2009
-2-
PRICE LIST - EXPORT
“KAT” TRAVEL CARRIAGE/AUTO WELD COMBO - USING THE GULLCO 24 VOLT D.C. GSP
CONTROL
For operation on either 42 / 115 / 230 volts, single phase, 50/60 HZ A.C. Power Supply
*Refer to “Page 1” for Carriage Travel Speed Ranges
PART NO.
GK-200-RL*A
GK-200-RM*A
GK-200-RH*A
DESCRIPTION
PRICE
“KAT” Travel Carriage/Auto Weld Combination for “Rigid Track” ....................
With heavy duty self-aligning wheel assemblies, closed loop tack feed back
for accurate speed control when running in any plane, regardless of load.
Maximum 100 lbs. (45 kgs). Carriage is controlled by the Gullco low voltage
24 volt GSP microprocessor pulsed width modulation motor control, interfacing
with the forward/stop/reverse switch and infinitely variable 4-turn speed
potentiometer. Complete with three (3) limit switches – forward, reverse and
center. LED display in IPM or cm/min and with a ten position rotary switch to
adjust various functions, listed below to provide the desired automatic cycles.
0.
1.
2.
3.
4.
5.
6.
7.
8.
9.
Note:
Operating position.
Travel start delay after arc start signal, adjustable 0 – 9.9 seconds.
Crater fill delay, allowing the wire feed signal to stay active after
carriage stop, adjustable 0 – 9.9 seconds.
Post weld delay, sets a delay adjustable 0 – 9.9 seconds after each
crater fill delay for burnback or postflow to occur.
Weld direction – forward, reverse, or ‘forward and reverse’
Center limit switch use, to enable rapid traverse to weld start point
using center limit switch.
Stitch weld electronically programmed using carriage travel distance,
adjustable 0.1 – 99.9 inches or centimeters, or use of center limit
switch with template.
Stitch no weld electronically programmed using carriage travel
distance, adjustable 0.1 – 99.9 inches or centimeters.
Automatic carriage return to home. Limit switch activated.
Continual forward and reverse of carriage using limit switch activators.
Center limit switch activator(s) to be supplied by the customer.
GK-200-FL*A
GK-200-FM*A
GK-200-FH*A
“KAT” Travel Carriage/Auto Weld Combination “For Flexible Track” ..............
The Flex “KAT” Carriage Auto Weld Control Combo is supplied complete, as
described above, except for use on flexible track.
GSP-2013
Remote Pendant Control Kit for all above Kats ...................................................
February 1, 2009
-3-
PRICE LIST - EXPORT
“KAT” TRAVEL CARRIAGE FOR INTERFACE
WITH STAR-TRAC II GOUGING CONTROLLER
For Operation on either 115/230 Volts single phase 50/60 Hz. A.C. Power supply
*Specify voltage when placing order – B = 115 V – C = 230 V
PART NO.
DESCRIPTION
PRICE
GK-200-RH*G
“KAT” Travel Carriage (Rigid) Interface with Star-Trac II Gouging Controller .
Complete with Heavy-Duty self-aligning wheel assemblies, closed loop tack
feedback for accurate speed control when running in any plane, regardless
of load. (Maximum 100 lbs. [45 kgs]). The carriage is controlled by the Gullco
low voltage 24-volt GSP microprocessor pulse width modulation motor control
with interface for Star-Trac II Gouging Controller, forward/stop/reverse
switch and infinitely variable 4-turn speed potentiometer. The LED display is in
IPM or cm/min. The motor control can be upgraded to provide auto
forward/reverse limit switches.
Carriage Speed Range: 2.7 – 88.4 IPM (6.7 224 Cm/Min)
GK-200-FH*G
“KAT” Variable Speed Travel Carriage for Flexible Track, ................................. $
Heavy-duty self-aligning wheel assemblies, closed loop tack feedback for accurate
speed control when running in any plane, regardless of load. (Maximum 100 lbs.
[45 kgs]). The carriage is controlled by the Gullco low voltage 24 volt GSP
microprocessor pulse width modulation motor control with interface for StarTrac II Gouging Controller, forward/stop/reverse switch and infinitely variable
4-turn speed potentiometer. The LED display is in IPM or cm/min. The motor
control can be upgraded to provide auto forward/reverse limit switches.
Carriage Speed Range: 4.2 – 139.1 IPM (10.6 - 353 Cm/Min)
Star Trac II
Digital Gouging System.......................................................................................... $
High resolution voltage control regulates accurate gouging depth to a ± .015” (0.4mm)
for use with 3/8” to 5/8” jointed gouging electrodes up to 1200 amps, single phase AC
115 volts, 50/60 hz, 100 watts. NOTE: Supplied as standard with 3/8” shoe cap,
unless otherwise stated.
**
ACCESSORIES FOR MOUNTING ON “KAT”
GK-200-004
Control and Cable Support Assembly ..................................................................
GK-190-650
Extra Heavy-Duty Rack Box ...................................................................................
10” (254 mm) long with adjustable nylastic bearing plugs for 1-1/2” (38 mm)
square rack arm.
GK-190-047-3
24” (609.6 mm) long, Extra Heavy-Duty 1-1/2” (38 mm) square rack arm .........
With rack and both ends turned to 1-1/8” (29 mm) diameter.
GK-165-068
Bronze Cutting Torch Holder Imperial Bore ......................................................... $
For 1-3/8” (35 mm) diameter rack type cutting torch, 32 pitch rack with swivel
clamp.
GK-190-066
Rack Box Riser Bracket…………………………………………………………………..
Provides an adjustable mounting surface – 2” (50.8 mm), 4” (101.6 mm) or
6” (152.4 mm) above the normal “Kat” Carriage Rack Box Mounting surface.
**Consult Factory
February 1, 2009
-4-
PRICE LIST - EXPORT
“KAT” LOWER HOUSING CONVERSION PARTS
PART NO.
DESCRIPTION
PRICE
PARTS REQUIRED TO CONVERT A RIGID “KAT” TO RUN ON FLEXIBLE TRACK
GK-192-F-008
Cam Fork ..........................................................................................................
GK-192-F-012
Motor Drive Pinion ................................................................................................
GK-192-F-034
Drive Gear Sprocket Assembly..............................................................................
GK-192-F-065
Wheel Assembly....................................................................................................
(Price shown is for one (1) wheel assembly, four (4) required).
PLEASE NOTE: High and low speed gear train assemblies cannot be
used with Flexible “KAT” Carriage.
PARTS REQUIRED TO CONVERT A FLEXIBLE “KAT” TO RUN ON RIGID TRACK
GK-165-008
Cam Fork ............................................................................................................
GK-165-012
Motor Pinion ........................................................................................................
GK-165-034
Idler Gear Assembly................................................................................................ $
GK-165-154
Heavy Duty Wheel Assembly .................................................................................
(Price Shown is for one (1) wheel assembly, four (4) required).
February 1, 2009
-5-
PRICE LIST - EXPORT
“KAT” CARRIAGE GEAR TRAINS AND ACCESSORIES
PART NO.
GK-166-153
DESCRIPTION
High Speed Gear Train Assembly .........................................................................
For installation on “KAT” Carriage to provide the following alternative speed
ranges:
“KAT” MODEL
GK-200-RL
GK-200-RM
GK-200-RH
GK-166-169
PRICE
SPEED RANGE
1.30 – 43.6 IPM (3.30 – 111 cm/min)
2.60 - 87.3 IPM (6.60 – 222 cm/min)
7.10 – 236 IPM (18.0 – 598 cm/min)
Low Speed Gear Train Assembly ..........................................................................
For installation on “KAT” carriage to provide the following alternative speed
ranges.
“KAT” MODEL
GK-200-RL
GK-200-RM
GK-200-RH
SPEED RANGE
0.20 – 7.0 IPM (0.5 – 17.7 cm/min)
0.40 – 14.0 IPM (1.0 – 35.5 cm/min)
1.10 – 37.7 IPM (2.9 – 95.8 cm/min)
GK-184-100
Friction Drive Undercarriage/Circle Cutting Attachment .................................... $
For “KAT” GK-200. 36” (914 mm) Radius Arm Attachment, plate centering pin
and centering pin magnet holder.
GK-190-067
Bottom Dust Gear Cover for “KAT” (Rigid Track) ............................................... $
GK-190-068
Bottom Dust Gear Cover for “KAT” (Flexible Track)...........................................
UK 1030
Transformer, 230/42v, 1000va, two sockets ........................................................ $
UK 1037
Transformer, 230/110v, 1000va, two sockets ...................................................... $
UK 1040
Transformer, 230/42v, 500va, two sockets .......................................................... $
UK 1047
Transformer, 230/110v, 500va, two sockets ........................................................ $
February 1, 2009
-6-
PRICE LIST - EXPORT
“KAT” HYDRAULIC CARRIAGE
PART NO.
DESCRIPTION
PRICE
GK-190-H-018
Hydraulic “KAT” Carriage ......................................................................................
For use with rigid aluminum track. Speed 0 to 4.9 IPM. (0 to 12.4 cm/min)
Motor complete with quick connect couplings for inlet and outlet hydraulic
hoses.
GK-190-H-036
For use with rigid aluminum track. Speed range .5 to 9.8 IPM. (1.25 to 24.89
cm/min) - Motor complete with quick connect couplings for inlet and outlet
hydraulic hoses.
GK-190-H-090
For use with rigid aluminum track. Speed range 1 to 26.5 IPM. (2.54 to 67.31
cm/min). Motor complete with quick connect couplings for inlet and outlet
hydraulic hoses.
GK-190-H-017
For use with flexible track. Speed range 0 to 7.5 IPM. (0 to 19.05 cm/min).
hoses.
GK-190-H-035
For use with flexible track. Speed range 1 to 15 IPM. (2.54 to 38.1 cm/min).
hoses.
GK-190-H-089
For use with flexible track. Speed range 2 to 40.5 IPM. (5.08 to 102.87
cm/min). Motor complete with quick connect couplings for inlet and outlet
hydraulic hoses.
DO NOT INCREASE THE LENGTH OF HOSE
PLEASE NOTE:
ALL HYDRAULIC CARRIAGES INCORPORATE THE FOLLOWING:
•
•
•
•
•
A protective cover over the drive gear opening;
Heavy duty wheel assemblies;
The lower housing and wheel assembly are hard anodized plus
dry lube on the wheel assembly mating surface.
All gears and metallic parts are plated.
Motor complete with quick connect couplings for inlet and outlet
hydraulic hoses.
Note that the information on speeds is based on having oil pressure of
1,000 psi. (69 bars) with a flow of 4 gallons (18.2 liters) per minute.
February 1, 2009
-7-
PRICE LIST - EXPORT
“KAT II” ALL POSITION VARIABLE SPEED TRAVEL CARRIAGE FOR RIGID TRACK
For operation on either 42 / 115 / 230 volts, single phase, 50/60 HZ A.C. Power Supply
Specify Voltage When Placing Order
PART NO.
GK-189-045-*
DESCRIPTION
PRICE
“KAT II” Variable Speed Carriage only ................................................................. $
2 – 46 IPM (5 – 114 cm/min) electronic drive with dynamic braking, speed
potentiometer, fuse, forward/reverse switch, run/stop power ON light. Load
capacity 50 lbs. (22.68 kg) vertical.
Price for Cutting Package Accessories: ............................................................... $
Includes:
One (1) GK-165-052-1 “Rigid” Kat Track 96” (2438 mm) Long.
Two (2) GK-165-219 Track Mounting Device with (1) round magnet and (1)
angle bracket .
One (1) GK-165-217 Track Mounting Device with two angle brackets.
One (1) GK-189-054 Welding / Cutting Torch Rack Accessory Kit.
Incorporates vertical mounting post with 360 degree pivot; two (2) independent
horizontal rack adjustments; one (1) vertical rack adjustment and a universal
torch holder will accept either welding gun or a standard machine type cutting
torch.
TORCH OPTIONS:
SMITH
HARRIS
VICTOR
***
***
***
***Consult Factory
February 1, 2009
-8-
PRICE LIST – EXPORT
“KAT II” ACCESSORIES
PART NO.
DESCRIPTION
PRICE
Cutting Package Accessories: ...................................................................................................
One (1) GK-165-052-1 “Rigid” Kat Track 96” (2438 mm) Long.
Two (2) GK-192-405 Track Mounting Devices with one on/off magnet and one
angle bracket.
One (1) GK-192-408 Track Mounting Device with two angle brackets
One (1) GK-171-650 Standard 1-1/8” (29 mm) Rack Box.
One (1) GK-171-047-2 18” (457.2 mm) long 1-1/8” (29 mm) Rack Arm.
One (1) GK-165-068 Standard Cutting Torch Holder for 1-3/8” (34 mm) rack
type cutting torch 32-pitch.
One (1) GS-010-031 3-Hose Manifold Block (plus fittings).
One (1) GK-181-025 Hoses with fittings, 36” (914 mm) long (1 set, 3 pieces).
Price for Welding Package Accessories: .........................................................................................
Same as above, less GK-165-068 Cutting Torch Holder, GS-010-031 Manifold
Block, and GK-181-025 hoses, but includes:
One (1) GK-165-074-2 – 4-Motion Semi-Automatic Welding Gun Holder.
Alternate to above:
GK-189-054
Welding / Cutting Torch Rack Accessory Kit. ...................................................... $
Incorporates vertical mounting post with 360 degree pivot; two (2) independent
horizontal rack adjustments; one (1) vertical rack adjustment and a universal
torch holder will accept either welding gun or a standard machine type cutting torch.
(sold as complete kit only)
Additional “Kat II” Options:
GK-184-200
Circle Cutting Attachment ......................................................................................
For standard “KAT II” comprising of undercarriage, 36” (914 mm) radius arm,
arm attachment, plate centering pin and magnet holder for centering pin.
GK-181-025
Hoses with fittings, 36” (914 mm) long (1 set, 3 pieces) ........................................
GS-010-031
3-Hose Manifold Block (includes fittings) ...............................................................
February 1, 2009
-9-
PRICE LIST - EXPORT
1-1/8” (29 MM) RACK BOXES, RACK ARMS AND CLAMPS
PART NO.
DESCRIPTION
PRICE
GK-171-650
Heavy-Duty Rack Box ............................................................................................
6” (152.4 mm) long with adjustable nylastic bearing plugs, for 1-1/8” (29 mm)
square rack arm.
GK-171-655
As above, except with micro fine adjustment gear box ......................................
GK-171-685*
Heavy-Duty Rack Box .............................................................................................
6” (152.4 mm) long with adjustable nylastic bearing plugs for 1-1/8” (29 mm)
square rack arm, with 3/8” threaded stud with 1-1/8” (29 mm) swivel clamp.
GK-171-690*
Rack Boxes available in lengths up to 36” (914.4 mm) – additional cost
$31.00 per inch (25 mm) plus $94.00 set-up charge.
GK-171-231
Two Heavy-Duty Rack Boxes................................................................................. $
6” (152.4 mm) long with adjustable nylastic bearing plugs for 1-1/8” (29 mm)
rack arms joined to provide vertical and horizontal adjustment.
GK-171-235
GK-171-700
Special Heavy Duty Roller Rack Box ....................................................................
8” (203 mm) long with rollers in place of nylastic bearing plugs for 1-1/8” (29
mm) square rack arm.
GK-171-705
GK-171-047-1
12” (304.8 mm) long Heavy-Duty 1-1/8” (29 mm) Square Rack Arm
With rack and one end turned to 1-1/8” (29 mm) diameter.
GK-171-047-2
18” (457.2 mm) long heavy duty 1-1/8” (29 mm) Square Rack Arm
GK-171-047-3
24” (609.6 mm) long heavy duty 1-1/8” (29 mm) Square Rack Arm
GK-171-047-4
36” (914.4 mm) long heavy-duty 1-1/8” (29 mm) Square Rack Arm
Other additional lengths available up to 72” (1828.8 mm) – additional
Cost $12.38 per inch (25 mm) plus $94.00 set-up charge.
GK-166-183
Swivel Clamp ........................................................................................................
1-1/8” (29 mm) diameter for use with 1-1/8” (29 mm) and 1-1/2” (38 mm) Rack
Arms.
GK-166-236
Square Clamp ........................................................................................................
1-1/8” (29 mm) diameter for use with 1-1/8” (29 mm) Rack Arms.
* Can be supplied with square clamp
February 1, 2009
- 10 -
PRICE LIST - EXPORT
1-1/2” (38 MM) RACK BOXES, RACK ARMS AND CLAMPS
PART NO.
DESCRIPTION
PRICE
GK-190-650
Extra Heavy-Duty Rack Box ...................................................................................
square rack arm.
GK-190-655
GK-190-685*
Extra Heavy Duty Rack Box ...................................................................................
square rack arm with 3/8” threaded stud with 1-1/8” (29 mm) swivel clamp.
GK-190-690*
As above, except with micro fine adjustment gear box
Rack Boxes available in lengths up to 36” (914.4 mm) – additional
Cost $35.00 per inch (25.4 mm) plus $94.00 set-up charge.
GK-190-231
Two Extra Heavy-Duty Rack Boxes.......................................................................
rack arms joined to provide both vertical and horizontal adjustment.
GK-190-235
As above, except with micro fine adjustment gear box ...................................... $
GB-413-030
Special Extra Heavy Duty Roller Rack Box .......................................................... $
10” (254 mm) long with rollers in place of nylastic bearing plugs for 1½” (38
mm) square rack arm.
GB-414-030
As Above, except with micro fine adjustment gear box .....................................
GK-190-047-2
GK-190-047-3
GK-190-047-4
36” (914.4 mm) Long, Extra Heavy Duty 1-1/2” (38 mm) square rack arm ........
Other additional lengths available up to 72” (1828.8 mm). Additional
Cost $15.60 per inch (25.4 mm) plus $94.00 set-up charge.
GK-190-236
Square Clamp 1-1/2” (38 mm) ................................................................................
For use with 1-1/2” (38 mm) rack arms.
*Can be supplied with square clamp.
February 1, 2009
- 11 -
PRICE LIST - EXPORT
GUN/TORCH HOLDERS, RACK BOX RISER BRACKET, CABLE SUPPORT
AND MICRO CROSS SLIDE
PART NO.
DESCRIPTION
PRICE
GK-190-066
Rack Box Riser Bracket..........................................................................................
Provides an adjustable mounting surface – 2” (50.8 mm), 4” (101.6 mm) or 6”
(152.4 mm) above the normal “KAT” Carriage Rack Box mounting surface.
System complete with mounting screws and can accommodate both rack
boxes. Models GK-171-650 heavy duty 1-1/8” (29 mm) and GK-190-650 extra
heavy duty 1-1/2” (38 mm).
GK-190-088**
4-Motion Semi-Automatic Welding Gun Attachment........................................... $
With micro fine adjustment gear box to mount on the horizontal rack arm used
with the “KAT” Carriage to provide 6-1/2” (165 mm) vertical adjustment, 360
degrees torch rotation with two-directional angle tilt, with gun holder suitable
for most semi-automatic welding guns (jaws adjustable from 5/8” (16 mm) to 11/2” (38 mm) with swivel clamp. All adjustments made with quick acting lever
clamps.
GK-165-074-2**
As Above, except with standard rack box ............................................................ $
GK-165-145**
Semi-Automatic Gun Holder Assembly ................................................................
Will accept most semi-automatic welding guns jaws adjustable from 5/8” (16
mm) to 1-1/2” (38 mm) with swivel clamp. Adjustments made with quick acting
lever clamps.
GK-165-068**
Bronze Cutting Torch Holder Imperial Bore ......................................................... $
clamp.
GK-165-068M**
Bronze Cutting Torch Holder Metric Bore ............................................................ $
For 1-1/4” (32 mm) diameter rack type cutting torch 32 pitch rack with swivel
clamp.
GK-181-027
Cable Support Assembly........................................................................................
With swivel cable clamp for mounting on “KAT” carriage to prevent cable drag.
GK-186-300
Micro Cross Slide ...................................................................................................
Providing 1” (25.4 mm) micro fine adjustment on both X and Y axis with clamp
for GK-187-026 Semi-Automatic Gun Holder.
GK-186-309
Micro Cross Slide Link Arm Assembly .................................................................
GK-186-320
Torch Tilt Assembly ................................................................................................ $
Providing 360° micro fine adjustment for attachment to all semi-automatic gun
holders.
** Can be supplied with Square Clamp
February 1, 2009
- 12 -
PRICE LIST- EXPORT
MOTORIZED ARMS FOR POSITIONING WELDING GUNS OR CUTTING TORCHES
For Operation on either 42 / 115 / 230 volts, Single Phase 50/60 HZ. A.C. Power Supply
PART NO.
DESCRIPTION
PRICE
GK-190-201
Pendant Control required for Motorized Rack Boxes ......................................... $
For motorized rack arms with 4-way joystick control, adjustable speed
potentiometer, two (2) multi-pin outlets to run up to two (2) motorized rack
boxes, directional indicator lights, high speed override switch, 8 ft. (2438 mm)
power supply cord. For use with either 1-1/8” (29 mm) or 1-1/2” (38 mm)
heavy duty motorized rack boxes.
GK-190-214
Motorized Rack Box 1-1/8” (29 mm) ......................................................................
8” (203.2 mm) long, adjustable nylastic bearing plugs, screws for mounting on
“KAT” Carriage 24” (609.6 mm) long 1-1/8” (29 mm) rack arm. 10 ft. (3048
mm) control cable with quick disconnect plug for connection to pendant control
box.
GK-190-215
8” (203.2 mm) long, adjustable nylastic bearing plugs, 24” (609.6 mm) long 11/8” (29 mm) heavy duty rack arm, complete with a 3/8” threaded stud and 11/8” (29 mm) swivel clamp. (Square clamp available on request at no extra
charge). Complete with 10 ft. (3048 mm) control cable with quick disconnect
plug for connection to pendant control box.
GK-190-216
Two Motorized Rack Boxes 1-1/8” (29 mm)..........................................................
Two (2) 8” (203.2 mm) long, as per GK-190-214. Mounted at right angles to
provide up/down, in/out movement of the two (2) 24” (609.6 mm) long heavy
duty 1-1/8” (29 mm) rack arms. Complete with two (2) 10’ long (3048 mm)
control cables with quick disconnect plugs for connection to pendant control
box.
GK-190-217
10” (254 mm) long, adjustable nylastic bearing plugs, screws for mounting on
“KAT” Carriage and 24” (609.6 mm) long extra heavy-duty 1-1/2” (38 mm) rack
arm. Complete with 10 ft. (3048 mm) control cable with quick disconnect plug
for connection to pendant control box.
GK-190-218
10” (254 mm) long, adjustable nylastic bearing plugs, 24” (609.6 mm) long
extra heavy duty 1-1/2” (38 mm) rack arm, complete with a 3/8” x 2” (50.8 mm)
long threaded stud and 1-1/8” (29 mm) swivel clamp. (Square clamp available
on request at no extra charge). Complete with 10 ft. (3048 mm) control cable
with quick disconnect plug for connection to pendant control box.
February 1, 2009
- 13 -
MOTORIZED ARMS FOR POSITIONING WELDING GUNS OR CUTTING TORCHES
For operation on either 42 / 115 / 230 volts, Single Phase 50/60 HZ, A.C. Power Supply
PART NO.
GK-190-219
DESCRIPTION
PRICE
Two Motorized Rack Boxes 1-1/2” (38 mm)..........................................................
Two (2) 10” (254 mm) long, as per GK-190-217. Mounted at right angles to
provide up/down, in/out movement of the two (2) 24” (609.6 mm) long extra
heavy-duty 1-1/2” (38 mm) rack arms. Complete with two (2) 10 ft. (3048 mm)
control cables with quick disconnect plugs for connection to pendant control
box.
Rack Arms are available in lengths up to 6 ft. (1828.8 mm)
Additional cost 1-1/8” (29 mm) - $12.38 per inch (25.4 mm) plus $94.00 set-up
charge.
Additional cost 1-1/2” (38 mm) - $15.60 per inch (25.4 mm) plus $94.00 set-up
charge.
All 1-1/2” (38 mm) rack arms must have one end machined to 1-1/8” (29 mm)
diameter to accept all “KAT” torch accessories.
Additional lengths of motorized rack box control cable with multi-pin plugs on
one end is available at $140.00 plus $5.00 per 12” (304.8 mm).
February 1, 2009
- 14 -
MECHANICAL HEIGHT SENSORS AND FILLET WELD SEAM TRACKER
PART NO.
DESCRIPTION
PRICE
GK-190-001
Mechanical Height Sensor/Swivel Copper Guide Wheel.....................................
** with constant velocity spring, hardened and ground rods and re-circulating
ball bushings to give constant accurate torch to work piece distance, providing
1-3/4” (44 mm) of torch float, complete with mounting plate for “KAT” rack box.
Work surface contact adjustable swivel copper guide wheel.
GK-190-600
Mechanical Height Sensor/Swivel Copper Guide Wheel..................................... $
As above, except complete with 1-1/8” (29 mm) rack box, 12” (304 mm) rack
arm and swivel mounting clamp for attachment to “KAT” rack arm.
GK-190-601
Mechanical Height Sensor/Hardened Stainless Steel Ball..................................
** with constant velocity spring hardened and ground rods and re-circulating
ball bushings to give constant accurate torch to work piece distance, providing
1-3/4” (44 mm) of torch float, complete with mounting plate for “KAT” rack box.
Work surface contact hardened stainless steel ball assembly.
GK-190-602
Mechanical Height Sensor/Hardened Stainless Steel Ball.................................. $
As above, except complete with 1-1/8” (29 mm) rack box, 12” (304 mm) rack
arm and swivel mounting clamp for attachment to “KAT” rack arm.
GK-190-603
Fillet Weld Mechanical Seam Tracker ................................................................... $
With constant velocity spring, hardened and ground rods and re-circulating ball
bushings to give constant accurate torch to work piece distance, providing 13/4” (44 mm) of torch float, complete with 1-1/8” (29 mm) Rack Box, 12” (304
mm) rack arm. Micro cross slide providing ¾” (19 mm) x and y torch
adjustment and single copper guide wheel and gun holder.
GK-190-633
Same as above, except H.D. constant velocity spring ........................................ $
GK-190-604
Dual In-Line Copper Guide Wheels .......................................................................
GK-190-605
Dual Side-By-Side Copper Guide Wheels............................................................. $
Additional cost to increase float from 1-3/4” (44 mm) up to 6”
(152 mm) – add $ 50.00/inch (25 mm) plus $ 245.00 set-up charge.
For float over 6” (150 mm) – consult factory.
**
For Heavy Duty Spring, Add .................................................................................
GK-165-145
Semi-Automatic Gun Holder Assembly ................................................................
Will accept most semi-automatic welding guns jaws adjustable from 5/8” (16
mm) to 1-1/2” (38 mm) with swivel clamp. Adjustments made with quick acting
lever clamps.
GK-165-068
February 1, 2009
Bronze Standard Cutting Torch............................................................................. $
clamp.
- 15 -
TRACK SECTIONS
PART NO.
DESCRIPTION
PRICE
GK-165-052
48” (1219 mm) Length Aluminum Alloy Rigid Track Section .............................
Complete with rack and interlocking ends.
GK-165-052-1
96” (2438 mm) Length Aluminum Alloy Rigid Track Section .............................
GK-165-054
120” (3048 mm) Length Aluminum Alloy Rigid Track Section ...........................
GK-166-258
60” (1524 mm) Length Aluminum Alloy Deep Section Track..............................
Complete with joining plates.
GK-166-260
120” (3048 mm) Length Aluminum Alloy Deep Section Track............................
Complete with joining plates.
To internally stiffen GK-166-260 add..................................................................... $
To HARD anodize any of the above track to MIL Spec. A-8625,
Type 3, Class 1, add ................................................................................................ $
**
** Consult Factory
NOTE: FOR TRACK ROLLING/FORMING, SEE PAGE 17
FLEXIBLE TRACK
GK-192-F-054-2
Heavy Duty Flexible Track...................................................................................... $
8 ft. length (2438 mm) minimum diameter 60” (1524 mm) O.D., and I.D.,
complete with interlocking ends. Also available in custom lengths.
GK-192-F-057
Aluminum Flexible Track Stiffener ........................................................................
with fixing screws (32 pieces nut and bolts (1/4” – 20 x 1”). Note: The
stiffener can be rolled to a minimum diameter of 12 ft. (3.66 m) to use the
same bolt holes on the Flex Track. If a smaller diameter is required, new
holes must be drilled in the formed stiffener.
February 1, 2009
- 16 -
ADDITIONAL COSTS FOR ROLLING STANDARD TRACK SECTIONS
PART NO.
DESCRIPTION
PRICE
TRACK ROLLING
NOTE: THE FOLLOWING PRICES ARE TO BE ADDED TO THE
COST OF A RIGID TRACK SECTION
All lengths of track rolled to same radius – each ................................................
Forming a complete ring from “KAT” Track.........................................................
Forming “KAT” Track with a radius at a specific point on the track
leaving a specified amount of straight.
CRATING CHARGE:
1 – 4 pieces of same radius per crate ................................................................... $
February 1, 2009
- 17 -
TRACK MOUNTING DEVICES
PART NO.
DESCRIPTION
PRICE
GK-165-215
Track Mounting Device ...........................................................................................
Consisting of two (2) GK-165-211 magnets with on/off switch.
Track datum height 3-1/8” (79.4 mm).
GK-165-219
Consisting of one (1) GK-165-211 magnet with on/off switch, one (1) steel
angle bracket. Track datum height 3-1/8” (79.4 mm).
GK-165-217
Consisting of (2) steel angle brackets. Track Datum Height 3-1/8” (79.4 mm).
GK-165-138
Consisting of two (2) GK-165-205 magnets with release arm (capacity of
straight lift 200 lbs. (90 kgs.) Track datum height 2-7/8” (73 mm).
GK-192-406
Consisting of one (1) GK-165-205 magnet with release arm, one (1) steel
angle bracket. Track datum height 2-7/8” (73 mm).
GK-192-407
Consisting of two (2) steel angle brackets. Track datum height 2-7/8” (73 mm).
GK-165-128
Self-Aligning Track Mounting Device.................................................................... $
Consisting of two (2) GK-165-205 self-aligning magnets with release arm
(capacity of straight lift 200 lbs. (90 kgs). Track datum height 3-3/16” (81.0
mm).
GK-190-129
Consisting of one (1) GK-165-205 magnet with release arm, one (1) steel
GK-190-128
For self-aligning magnet assembly consisting of two (2) steel angle brackets.
GK-165-136
Consisting of two (2) GK-165-206 magnets with on/off switches (capacity of lift
150 lbs. {68 kgs}). Track datum height 3-7/8” (98.4 mm).
GK-192-405
Consisting of one (1) GK-165-206 magnet with on/off switch, one (1) steel
February 1, 2009
- 18 -
TRACK MOUNTING DEVICES, Cont’d….
PART NO.
DESCRIPTION
PRICE
GK-192-408
Track Mounting Device ........................................................................................... $
Consisting of two (2) steel angle brackets. Track datum height 3-7/8” (98.4
mm).
GK-165-125
Consisting of two (2) GK-165-206 self-aligning magnets with on/off switches
capacity of straight lift 150 lbs. (68 kgs). Track datum height 4-3/16” (106.4
mm).
GK-190-127
Self Aligning Track Mounting Device....................................................................
Consisting of one (1) GK-165-206 self-aligning magnet with on/off switch, one
(1) steel angle bracket. Track datum height 4-3/16” (106.4 mm).
GK-190-126
Track Mounting Device ........................................................................................... $
For self-aligning magnet assemblies consisting of two (2) steel angle brackets.
GK-165-205
Single Magnet with Release Arm........................................................................... $
capacity of straight lift 100 lbs. {45 kgs)
GK-165-205-1
As above, .......................................................................................................
except with hole through center to suit ¼” (3.175 mm) flat head machine
screw
GK-165-206
Single Permanent Type Magnet............................................................................. $
With on/off switch (capacity of straight lift 75 lbs. {34 kgs}.)
GK-165-200
Track Mounting Pad ................................................................................................ $
Providing necessary clearance between “KAT” Carriage and work mounting
devices. Height 1-1/4” (31.75 mm). Other heights available upon request.
GK-165-039
Aluminum Support Bar
For holding magnets or other mounting brackets.
GK-166-406
Steel Mounting Feet ................................................................................................ $
One (1) pair with fixing screws. Please specify whether for use with GK-165136/GK-165-125 track mounting devices with on/off switches or GK-165-138/
GK-165-128 track mounting devices with magnets having release arm.
February 1, 2009
- 19 -
TRACK MOUNTING DEVICES, Cont’d….
PART NO.
DESCRIPTION
PRICE
GK-190-145
Quick Release Plunger-type track mounting assembly ...................................... $
299.00
GK-190-110
Pivoting Track Mounting Device............................................................................ $
For spherical tanks comprising two (2) GK-165-205 self-aligning magnets with
release arm; one (1) steel bracket; one (1) 90° pivot bracket assembly and
magnet support bar.
333.00
GK-190-107
Pivoting Track Mounting Assembly ...................................................................... $
For fitting to standard track mounting devices (no magnets, steel angle bracket
or magnet support bar).
136.00
GK-190-046
Perpendicular Track Mounting Bracket 9” (228.6 mm) high............................... $
Can be used with any track mounting device.
21.00
RECOMMENDED MINIMUM NUMBER OF MAGNET ASSEMBLIES
FOR STANDARD ALUMINUM ALLOY TRACK
Two (2) magnet assemblies for 48” (1219 mm) track section.
Three (3) magnet assemblies for 96” (2438 mm) track section.
Four (4) magnet assemblies for 120” (3048 mm) track section.
IMPORTANT SAFETY INFORMATION;
For out-of-position applications, additional magnet assemblies and/or tack welded
Steel mounting feet will be required for safety – quantity depending on the amount
Of accessory equipment being carried by the “KAT” Carriage.
FLEXIBLE TRACK - RECOMMENDED MAGNET AND VACUUM ASSEMBLIES
SEE PAGE 21.
February 1, 2009
- 20 -
HOLDING DEVICES FOR FLEX TRACK
PART NO. GK-192-F-054-2
SUGGESTIONS ON USE OF MAGNETS AND MAGNET ACCESSORIES
Recommended eight (8) assemblies for heavy-duty flexible track GK-192-F-054-2 magnetic track
mounting devices Part No. GK-165-136 or GK-165-138. (See price list for suggested magnet
selections).
If additional stiffness or support is required for the above, add intermediate assemblies using any
one of the following:
Double Magnet Track Mounting Device Part No. GK-165-136 or GK-165-138.
Single magnet with angle bracket Track Mounting Device Part No. GK-192-406 or
GK-192-405.
Double Angle Bracket Track Mounting Device Part No. GK-192-408 or GK-192-407.
SUGGESTIONS ON USE OF VACUUM AND VACUUM ACCESSORIES
Recommended eight (8) assemblies for heavy duty flexible track GK-192-F-054-2 using vacuum
cup sub-assemblies. Complete eight (8) assemblies – Part No. GV-192-F-409.
If additional stiffness or support is required for the above, add intermediate assemblies using any of
the following:
Vacuum sub-assembly (2 vacuum cups) Part # GV-168-083-2 – GV-168-055 (See
Page 22).
Double Angle Stainless Steel Bracket track mounting device (for vacuum). Part No.
GV-192-F-410.
February 1, 2009
- 21 -
VACUUM EQUIPMENT
For Operation on 115 / 230 Volt, Single Phase 50/60 HZ., A.C. Power Supply
Specify Voltage when placing order
PART NO.
DESCRIPTION
PRICE
GV-168-060
Portable Vacuum Unit ............................................................................................. $
Comprising of motor driven vacuum pump, capacity 2.4 CFM (67.9 liters/min),
vacuum gauge, filter, non-return valve and all necessary fittings including 10
feet (3048 mm) flexible hose with quick disconnect coupling.
GV-168-050
Portable Vacuum Unit ............................................................................................. $
As above except mounted on cylindrical safety reservoir.
VACUUM CUP ASSEMBLIES FOR “KAT” RIGID TRACK
GV-168-051-A
Vacuum Assembly for 48” (1219 mm) Rigid “KAT” Track .................................. $
Comprising of two (2) vacuum manifold block mounting units at 30” (761 mm)
centers with flexible hose between manifolds and male quick connect coupling
for connection to vacuum pump hose.
GV-168-053-A
Vacuum Assembly for 96” (2438 mm) Rigid “KAT” Track .................................. $
Comprising of three (3) vacuum manifold block mounting units at 30” (761 mm)
GV-168-070-A
Vacuum Assembly for 120” (3048 mm) Rigid “KAT” Track
Comprising of four (4) vacuum manifold block mounting units at 30” (761 mm)
VACUUM CUP ASSEMBLIES FOR “KAT” FLEXIBLE TRACK
GV-192-F-409
Vacuum Assembly for 8 ft. (2438 mm) Flexible Track .........................................
Model GK-192-F-054-2 comprising of eight (8) vacuum block mounting units
at 12” (304.8 mm) centers complete with flexible hose between manifolds,
intermediate center shut-off valve and male quick connect coupling for
connection to vacuum pump hose.
NOTE:
When joining one length of track to another a flexible vacuum hose
Assembly is required (Part No. GV-168-071 – see Page 23).
February 1, 2009
- 22 -
VACUUM CUPS AND ACCESSORIES
PART NO.
DESCRIPTION
PRICE
GV-168-083-1
Manifold Mounting Unit (Connecting End) ...........................................................
Comprising of:
One (1) only GV-168-056 Manifold Block, one (1) only GK-165-200 mounting
pad, two (2) only GV-168-054 Vacuum Cups. The manifold block is equipped
with one (1) quick disconnect coupling suitable for connection to the end of the
vacuum pump, or connecting one track assembly to another, (Part No. GK168-009), two (2) only GF-168-007 plugs, one (1) only GK-168-003 Male Pipe
Connector.
GV-168-083-2
Manifold Mounting Unit (Blocked End) .................................................................
Similar to above, but with the following pipe fittings:
Three (3) only GF-168-007 plugs, one (1) only GF-168-003 Male Pipe
Connectors.
GV-168-055
Manifold Mounting Unit (In Between)....................................................................
Similar to GV-168-083-2, but with the following pipe fittings:
Two (2) only GF-168-007 plugs, two (2) only GF-168-003 Male Pipe
Connectors.
GK-192-077
Manifold Interconnecting Hose..............................................................................
Price per foot (304.8 mm)
GV-192-F-076
Hose Clamps, Each .................................................................................................
GV-168-071
Flexible Vacuum Hose Assembly ..........................................................................
36” (914 mm) length complete with hose connector on one end and quick
disconnect coupling (male and female) on the other end for connecting the
vacuum assemblies of two track sections.
Each vacuum cup is capable of sustaining a load of 100 lbs (45 kg), at 20”
(508 mm) of vacuum.
NOTE:
WHEN ORDERING, PLEASE SPECIFY IF VACUUM ASSEMBLIES
ARE TO BE USED WITH MULTIPLE TRACK SECTIONS.
February 1, 2009
- 23 -
HEAVY-DUTY BRIDGE GANTRY CARRIAGES AND TRACK
For Operation on either 42 / 115 / 230 volt, 50/60 HZ Power Supply
PART NO.
DESCRIPTION
GK-190-P-023
Heavy Duty Power Drive Carriage ......................................................................... $
Providing a 12” x 48” (305 mm x 1219 mm) flat surface for mounting
equipment with heavy-duty cam rollers for running on special stiffened track.
24 volt D.C. motor with positive rack and pinion drive. Closed loop tack feedback for accurate speed control. The carriage is controlled by the Gullco low
feed start. Prices shown below. Speed range 2.7 – 88.4 IPM (6.7 – 224
cm/min) (Other speeds on request). Load capacity 1,500 lbs. (680 kg).
GK-190-P-026
5 ft. (1524 mm) length special Deep Section Track .............................................
With hardened steel wear strips on top surface, heavy-duty rack edge mounted
for above power drive carriage, ends are machined for accurate fit-up with
internal stiffening.
GK-190-P-025
10 ft. (3048 mm) length as above...........................................................................
GK-190-P-024
Heavy Duty Idler Carriage....................................................................................... $
Providing a 12” x 48” (305 mm x 1219 mm) flat surface for mounting
equipment with heavy-duty cam rollers for free running on special stiffened
track. Load capacity 1,500 lbs. (680 kg).
GK-189-044
Light Duty Small Idler Carriage
Providing a 6” x 10” (152 mm x 254 mm) flat mounting surface complete with
position lock.
GK-190-P-027
5 ft (1524 mm) length of Special Deep Section Track..........................................
With hardened steel wear strips on top surface, suitable for above Free
Running Idler. (“NO RACK”) with internal stiffening.
GK-190-P-028
10 ft. (3048 mm) length as above...........................................................................
PRICE
Carriages available in lengths 24” (610 mm) to 60” (1524 mm)
GK-191-P-071
Including relay, circuit board, mounting hardware, multipin connector with 15 ft.
GK-191-P-045-S
limit switch activators to stop Carriage when limit switches are activated.
GSP-2013
Comprising Remote Pendant (no control) attached to 8 ft. (2438 mm) control
cable one end and “KAT” control blanking plate other end with internal
- 24 All Prices Canadian Dollars
February 1, 2009
“KAT” CARRIAGE/AUTOMATIC INDEXER COMBO
For Operation on either 42 / 115 / 230 volts, Single Phase 50/60 HZ, A.C. Power Supply
PART NO.
GK-200-RL*I
GK-200-RM*I
GK-200-RH*I
DESCRIPTION
PRICE
“KAT” Travel Carriage/Torch Indexing Combination for Rigid Track ............... $
Heavy duty self-aligning wheel assemblies, closed loop tack feed back for
accurate speed control when running in any plane, regardless of load. Maximum 100 lbs. (45 kgs). Two (2) limit switches with adjustable track mounted
limit switch activators for auto forward and reverse of carriage. The carriage
and torch indexer are controlled by Gullco low voltage 24 volt GSP
microprocessor pulse width modulation motor controls interfacing the “KAT”
Carriage with the forward/stop/reverse switch and infinitely variable 4-turn
speed potentiometer, limit switches, LED display in IPM or cm/min and
interfacing the torch indexing arm with various functions listed below to provide
the desired automatic cycle, programmable through a 10-position rotary switch
included with indexer is a Rack Box Riser Bracket.
“KAT” CARRIAGE PROGRAMMING OPTIONS
1. Travel start delay after arc start signal, adjustable 0-9.9 seconds.
2. Arc on/off during index.
3. Crater fill delay, allowing the wire feed signal to stay active after
carriage stop. Adjustable 0-9.9 seconds.
4. Post weld delay. Sets the delay adjustable 0-9.9 seconds after each
crater fill delay for burnback or postflow to occur.
INDEXER CONTROL PROGRAMMING OPTIONS
1. Forward or reverse index direction
2. Index distance, 0.01 – 9.99 inches or cm.
The indexer is complete with a 36” (914 mm) long rack arm and indexer,
heavy-duty rack box, 1-1/8” (29 mm) complete with motor assembly. Limit
switches to stop the auto cycle and prevent rack arm over travel. Adjustable
Rack Arm limit switch stops, 4-motion semi-automatic gun holder to provide 6”
(152 mm) of vertical torch adjustment.
GK-200-FL*I
GK-200-FM*I
GK-200-FH*I
“KAT” Travel Carriage/Torch Indexing Combination for Flexible Track ........... $
Supplied, as described above, except for use on flexible track.
GK-181-027
Cable Support Assembly........................................................................................
With swivel cable clamp for mounting on “KAT” Carriage to prevent cable drag.
February 1, 2009
- 25 -
PRICE LIST - EXPORT
REMOTE CONTROL INDEXER
For Operation on either 42/ 115 / 230 volts, Single Phase 50/60 HZ, A.C. Power Supply
PART NO.
GK-202-100*
DESCRIPTION
PRICE
Remote Control Indexer for Miscellaneous Rotation Equipment
comprising of one (1) control box with switches for rack arm jog, cycle start
and speed potentiometer. The Index distance setting in a range from 0.01 to
9.99 in increments of 0.01. A single limit switch on 15 feet (4572 mm) cable to
provide index signal. One (1) only indexer motorized rack box for 1-1/8” (29
mm) rack arm 36” (914 mm) long providing 24” (609 mm) of variable speed
arm travel 1 to 32.7” per minute (25 to 83.1 cm/min) with limit switches to
prevent rack arm over-travel and to stop wire feeder. Two (2) adjustable rack
arm limit switch stops and one (1) four-motion welding gun holder.
INDEXER CONTROL PROGRAMMING OPTIONS
1.
2.
3.
4.
5.
6.
7.
8.
9.
February 1, 2009
Travel Motion Delay
Rotation Pause During Index
Arc On/Off During Index
Crater Fill Delay
Post Weld Delay
Index Direction
Index Distance
Rotation Signal Relay Setting
Index Prompt.
- 26 -
“KAT” CARRIAGE – COMPACT OSCILLATOR COMBO/REMOTE OSCILLATOR
For Operation on either 42 / 115 / 220 Volts, Single Phase 50/60 HZ, A.C. Power Supply
PART NO.
GK-200-RL*-O
GK-200-RM*-O
GK-200-RH*-O
DESCRIPTION
PRICE
“KAT” Travel Carriage/Compact Oscillator Combination for Rigid Track ........ $
Carriage complete with heavy-duty self-aligning wheel assemblies. Carriage
controlled by Gullco microprocessor based 24 volt D.C. programmable control
With closed loop tack feedback for accurate speed control when running in any
plane, regardless of load, maximum 100 lbs. (45 kgs.). The carriage is
controlled by the Gullco low voltage 24 volt GSP microprocessor pulse width
modulation motor control interfacing with the forward/stop/reverse switch, high
speed return and infinitely variable 4-turn speed potentiometer. The LED
display is in IPM or cm/min. The carriage incorporates the oscillator electronic
controls providing independent dwells at each end and the center of stroke,
infinitely variable 0 to 5 seconds; oscillation speed potentiometer, speed range
8 to 188 cycles per minute (16 to 376 passes per minute). Automatic wire feed
start; adjustable carriage delay start, adjustable 0 to 3 seconds; dwell on/off
switch; auto start switch; toggle switch to change oscillator mode from
standard angular oscillation pattern to step square wave oscillation pattern.
*Refer to “Page 1” for travel carriage speed ranges.
Other components included in the above system:
Independent oscillator head, Model GK-197-O-100; torch load capacity 5 lbs
@ 6” (2.268 kgs @ 152.4 mm) in either the horizontal or vertical plane. 1-1/8”
(29 mm) fine adjustment rack box with 18” (457 mm) long rack arm to provide
12” (305 mm) horizontal oscillator adjustment. 1-1/8” (29 mm) micro fine rack
box with 12” (305 mm) long rack arm to provide 6” (152 mm) vertical
adjustment together with torch holder for standard MIG welding gun, rack box
riser bracket and cable support assembly to prevent cable drag on the mig
gun.
GK-200-FL*-O
GK-200-FM*-O
GK-200-FH*-O
“KAT” Travel Carriage/Compact Oscillator Combination for Flexible Track....
Supplied as described above, except for use on a Flexible Track.
GK-194-O-014
Pendant Control for the Wire Feed on/off and Auto Start
For any of the above “KAT”/Oscillator combos. Pendant is on a 10 ft (3048
mm) of control cable with multi-pin connector for attachment to carriage. Must
be factory installed. (Price includes installation).
GK-197-004-RC
Remote Control Interface Kit.................................................................................. $
To interface remote control compact oscillator with any “KAT” Carriage. Kit
comprises a panel mounted connector and internal wiring harness for the
“KAT” Carriage, together with 15 ft. (4572 mm) connecting cable complete with
connectors at both ends.
*Can be used with all Remote Control Compact Oscillators.
February 1, 2009
- 27 -
LINEAR OSCILLATOR COMBO
PART NO.
DESCRIPTION
PRICE
GK-200-RL*-L
GK-200-RM*-L
GK-200-RH*-L
Linear “KAT” Oscillator System for Rigid Track .......................................
controlled by Gullco microprocessor based 24 volt D.C. programmable control with
closed loop tack feedback for accurate speed control when running in any plane,
regardless of load, maximum 100 lbs. (45 kgs.). Speed range 1 – 32.7 IPM (2.5 –
83.1 cm/min). The carriage is controlled by the Gullco new low voltage 24 volt GSP
microprocessor pulse width modulation motor control interfacing with the
forward/stop/reverse switch, high speed return and infinitely variable 4-turn speed
potentiometer. The LED display is in IPM or cm/min. The carriage incorporates the
oscillator electronic controls providing independent dwells at each end and the center
of stroke, infinitely variable 0 to 5 seconds; oscillation speed potentiometer, speed
range 8 to 188 cycles per minute (16 to 376 passes per minute). Electronic Oscillator
head control provides motorized Oscillation width potentiometer, oscillation center
line adjustment toggle switch and ten (10) program memory button. Automatic wire
feed start; adjustable carriage delay start, adjustable 0 to 3 seconds; dwell on/off
switch; auto start switch; toggle switch to change oscillator mode from standard
angular oscillation pattern to step square wave oscillation pattern.
Other components included in the above system: Independent stepper oscillator
head, Model GK-201-011; torch load capacity 10 lbs @ 6” (4.534 kgs @ 152.4 mm)
in either the horizontal or vertical plane. 1-1/8” (29 mm) fine adjustment rack box with
18” (457 mm) long rack arm to provide 12” (305 mm) horizontal oscillator adjustment.
1-1/8” (29 mm) micro fine rack box with 12” (305 mm) long rack arm to provide 6”
(152 mm) vertical adjustment together with torch holder for standard MIG welding
gun, rack box riser bracket and cable support assembly to prevent cable drag on the
mig gun.
GK-200-FL*-L
GK-200-FM*-L
GK-200-FH*-L
Linear “KAT” Oscillator System for Flexible Track ...................................
Supplied as described above, except for use on Flexible Track.
*Refer to “page 2” for travel carriage speed ranges.
GK-201-100-RC*-L Remote Linear Compact Oscillator with Dwells…………………………….$
Including all as outlined in GK-200-RL*-L (above), except NO “KAT”
CARRIAGE, All oscillator controls in remote pendant on 6 ft. (1828 mm) of
control cable.
February 1, 2009
- 28 -
RADIAL OSCILLATOR COMBO
PART NO.
DESCRIPTION
PRICE
GK-200-RL*-R
GK-200-RM*-R
GK-200-RH*-R
Radial “KAT” Oscillator System for Rigid Track .......................................
controlled by Gullco microprocessor based 24 volt D.C. programmable control
with closed loop tack feedback for accurate speed control when running in any plane,
regardless of load, maximum 100 lbs. (45 kgs.). Speed range 1 – 32.7 IPM (2.5 –
83.1 cm/min). The carriage is controlled by the Gullco new low voltage 24 volt GSP
microprocessor pulse width modulation motor control interfacing with the
forward/stop/reverse switch, high speed return and infinitely variable 4-turn speed
potentiometer. The LED display is in IPM or cm/min. The carriage incorporates the
oscillator electronic controls providing independent dwells at each end and the
center of stroke, infinitely variable 0 to 5 seconds; oscillation speed potentiometer,
speed range 8 to 188 cycles per minute (16 to 376 passes per minute). Electronic
Oscillator head control provides motorized Oscillation width potentiometer,
oscillation center line adjustment toggle switch and ten (10) program memory button.
Automatic wire feed start; adjustable carriage delay start, adjustable 0 to 3 seconds;
dwell on/off switch; auto start switch; toggle switch to change oscillator mode from
standard angular oscillation pattern to step square wave oscillation pattern.
Other components included in the above system: Independent stepper motor
oscillator head, Model GK-201-011; torch load capacity 5 lbs @ 6” (2.268 kgs @
152.4 mm) in either the horizontal or vertical plane. 1-1/8” (29 mm) fine adjustment
rack box with 18” (457 mm) long rack arm to provide 12” (305 mm) horizontal
oscillator adjustment. 1-1/8” (29 mm) micro fine rack box with 12” (305 mm) long rack
arm to provide 6” (152 mm) vertical adjustment together with torch holder for
standard MIG welding gun, rack box riser bracket and cable support assembly to
prevent cable drag on the mig gun.
*Refer to “Page 1” for Travel Carriage speed ranges.
GK-200-FL*-R
GK-200-FM*-R
GK-200-FH*-R
Radial “KAT” Oscillator System for Flexible Track
Supplied as described above, except for use on Flexible Track.
*Refer to “Page 2” for Travel Carriage speed ranges.
GK-201-100-RC*-R Remote Radial Compact Oscillator …………………………………………..$
Including all as outlined in GK-200-RL*-R (above), except NO “KAT”
CARRIAGE, All oscillator controls in remote pendant on 6 ft. (1828 mm) of
control cable.
February 1, 2009
- 29 -
PRICE LIST - EXPORT
OSCILLATORS
PART NO.
DESCRIPTION
PRICE
GK-197-001-RC-* Remote Control Compact Oscillator with dwells ................................................. $
Including all as outlined in GK-200-RL*-O, (Page 27) except NO “KAT”
CARRIAGE. All oscillator controls in remote pendant on 5 ft (1524 mm) of
control cable.
GS-474-001-RC-*
Remote Control Compact Oscillator No Dwells ...................................................
Including independent oscillator head Model GK-197-0-100S. No Dwells
complete with 1-1/8” (29 mm) fine adjustment Rack Box with 12” (305 mm)
long rack arm, torch holder for standard MIG Gun, oscillator mounting brackets
and remote control with programmable control in control box on 10 ft. (3048
mm) of control cable.
GK-194-O-300-*
Radial Oscillator ...............................................................................................
Capacity of oscillator head – 5 lbs @ 6” (2.268 kgs @ 152.4 mm). Maximum
oscillation width with standard MIG gun holder 0” to 1-1/2” (38.1 mm) with
3/16” (4.76 mm) adjustment while operating. Cycles – 350/max – 40/min.
Complete with 1-1/8” (28.57 mm) swivel clamp for attachment to “KAT” Rack
Arm. Remote control box on 10 ft. (3048 mm) of control cable with speed
potentiometer for oscillation cycles, forward/stop/reverse switch fuse holder
and 8 ft. (2438 mm) power cord.
GK-201-122
Radial Stepper Oscillator Head Only (No gun holder)......................................... $
Complete with necessary bracketry to mount in place of linear head.
•
Equipped with detachable cable assembly.
GK-201-123
Linear Stepper Oscillator Head Only (No gun holder).........................................
Complete with necessary bracketry to mount in place of radial head.
• Equipped with detachable cable assembly.
February 1, 2009
- 30 -
PRICE LIST - EXPORT
“MOGGY” FILLET WELDING TRACKLESS CARRIAGE
For Operation on 42 / 115 / 230 Volts single phase, 50/60 HZ A.C. Power Supply
PART NO.
DESCRIPTION
PRICE
GM-03-050*
“Moggy” Carriage with control for Continuous Travel ....................................
With speed potentiometer providing infinite speed selection 5.75 to 115 IPM
(14.6 to 292.1 cm/in). Adjustable guide rolls, travel limit switch assembly,
vertical and horizontal slides providing 1-3/4” (44.4 mm) adjustment and semiautomatic welding gun holder.
Forward/stop/reverse switch, wire feed
connector with 15 ft. (4572 mm) control cable, auto wire feed start with delay
carriage start and cable support clamp for mounting on handle.
GM-03-250*
“Moggy” Dual Torch Carriage with control for Continuous Trave
Complete as above except equipped for Dual Torch Operation. (Includes all
parts as listed in Part No. GM-01-070).
GM-03-100*
“Moggy” Carriage with control for stitch welding or continuous travel ...........
Complete as described above except with the addition of stitch weld control
using Gullco micro-processor to provide accurate repeatability for weld
distance on and weld distance off, regardless of travel speed. Adjustable
carriage start after wire feed start and adjustable wire feed stop after carriage
stop. All adjustments visible through LED window.
GM-03-200*
“Moggy” Dual Torch Carriage with control for stitch weld or
continuous travel complete as above except equipped for Dual Torch
Operation. (Includes all parts as listed in Part No. GM-01-070).
GM-01-075
6 ft. (1828.8 mm) long 6” (152.4 mm) wide V groove cutting machine track..... $
**
GM-01-076
9 ft. (2743.2 mm) long 6” (152.4 mm) wide V groove cutting machine track..... $
**
GM-01-065
Bronze Cutting Torch Holder ................................................................................. $
With swivel clamp for attachment to Moggy Torch Arm.
GM-01-070
Dual Torch Accessory ............................................................................................
Consisting of: counter balance, rack box with swivel clamp, 24” (609 mm) rack
arm, 4-motion torch holder and additional wire feeder outlet.
GM-03-059
Adjustable Guide Wheel Assemblies (2 required per Moggy) each
GM-03-060
Adjustable Lap Guide Wheel Assembly (2 required per Moggy) each
GM-01-091
Inside Radius Guide Arm Assembly…………………………………………………..$
GM-186-320
360° Torch Adjustment for Moggy.........................................................................
** Consult Factory
February 1, 2009
- 31 -
PRICE LIST - EXPORT
MAGNETIC “MOGGY” FILLET WELDING TRACKLESS CARRIAGE
For Operation on 42 / 115 / 230 Volts single phase, 50/60 HZ, A.C. Power Supply
PART NO.
DESCRIPTION
PRICE
GM-03-350*
Magnetic “Moggy” Carriage with control ............................................................. $
For continuous travel with magnetic base for out-of-position operation and
heavy-duty urethane 0.875” (22.23 mm) wide wheels with speed potentiometer
providing infinite speed selection 5.75 to 115 IPM (14.6 to 292.1 cm/min).
Adjustable guide rolls, travel limit switch assembly, vertical and horizontal
slides providing 1-3/4” (44.4 mm) adjustment and semi-automatic welding gun
holder. Forward/stop/reverse switch, wire feed connector with 15 ft. (4572
mm) control cable, auto wire feed start with delay carriage start and cable
support clamp for mounting on handle.
GM-03-300*
Magnetic “Moggy” Carriage with control ............................................................. $
For stitch welding or continuous welding with magnetic base for out-of-position
operation and heavy duty urethane 0.875” (22.23 mm) wide wheels. Complete
as described above except with the addition of stitch weld control using Gullco
micro-processor to provide accurate repeatability for weld distance on and
weld distance off, regardless of travel speed. Adjustable carriage start after
wire feed start and adjustable wire feed stop after carriage stop. All
adjustments visible through LED window.
GM-03-320
Magnetic Retro Fit Kit ............................................................................................. $
For Moggy Models GM-03-050 and GM-03-100.
NOTE: When the magnetic “Moggy” is used for out-of-position welding,
an anti-fall device must be attached.
GK-194-O-330
Radial Oscillator .................................................................................................
Capacity of oscillator head – 5 lbs @ 6” (2.268 kgs @ 152.4 mm). Maximum
oscillation width with standard MIG gun holder 0” to 1-1/2” (38.1 mm) with
3/16” (4.76 mm) adjustment while operating. Cycles – 350/max – 40/min.
Complete with 7/8” (22.2 mm) swivel clamp for attachment to Moggy Torch
Arm. Remote control box on 10 ft. (3048 mm) of control cable with speed
potentiometer for oscillation cycles, forward/stop/reverse switch fuse holder
and 8 ft (2438 mm) power cord.
February 1, 2009
- 32 -
PRICE LIST - EXPORT
“KAT” VERTICAL OVERLAY BRIDGE SYSTEM WITH OSCILLATION FOR BOILER TUBES
PART NO.
DESCRIPTION
PRICE
GS-474-030-90*
“KAT” Carriage Lower Unit ....................................................................................
With 15 ft. (4.6 m) interconnecting cable to upper carriage (other lengths
available on request).
GS-474-035-90*
“KAT” Carriage Upper Unit ....................................................................................
With 8ft. (2.4m) power cable and multipin connectors to supply power/control
signals to the lower and vertical “KAT” Carriages. Also equipped with a
connector for a single remote control to operate both upper and lower
carriages.
GS-441-021
Remote Control for Upper and Lower Carriage ...................................................
Connected to upper carriage with 15 ft. (4.6 m) control cable and multipin
connector, providing synchronized speed and direction control to both
carriages.
GS-474-065-090*
“KAT” Carriage Vertical Unit Assembly
Carriage with overhung load wheel extensions, limit switches and limit switch
stops, remote control for “KAT” with dual wire feed outlets, with two (2) 3.62
(1.1 m) arc start cables. Two (2) GK-197-O-100S Independent Oscillator
Heads (no dwells) with gun holders. Oscillators operated from a single control
mounted in the “KAT” Carriage with on/off switch and speed potentiometer.
One (1) GK-198-001 mounting assembly for two (2) oscillators comprising:
one (1) heavy-duty compound cross slide with 3.15” (80 mm) stroke for course
manual adjustment of the two (2) oscillator heads, and two (2) compound
cross slides with 1.97” (50 mm) stroke for fine manual adjustment of each
oscillator head independently. All mounted on an adjustable frame with
mounting plate to “KAT” Carriage, and front and back Carriage extensions.
GS-474-210
10 ft. (3048 mm) Heavy Duty Stiffened Vertical Track Assembly .......................
With interconnection cable and cable track from the upper carriage to the
vertical carriage, and vertical carriage counter-weight package, comprising of
pulley mechanism, weight and stainless steel cable.
Note: Other Lengths available at an additional price per foot (304.8 mm).......
Up to a maximum of 18 ft. (548.6 cm).
GS-474-201
Upper Special Idler Carriage .................................................................................
With heavy duty mounting plate, towing connector and vertical track mounting
bracket.
GS-441-017
Lower Special Idler Carriage..................................................................................
With heavy duty mounting plate, towing connector with roller bearing side
thrust assembly and adjustable slide block to hold vertical track in position.
NOTE:
FOR HORIZONTAL TRACK SECTIONS, SEE PAGE 16.
February 1, 2009
- 33 -
“KAT” VERTICAL OVERLAY BRIDGE SYSTEM
PART NO.
DESCRIPTION
PRICE
GS-474-050-18*
GS-474-050-36*
GS-474-050-90*
“KAT” Travel Carriage with oscillator (no dwells
Programmable microprocessor control in remote control box with 4-turn potentiometer, LED readout, run/stop switch. Limit switches and stops for weld speed
down, high speed return; dual wire feed outlets; one (1) 36” (914.4 mm) long
rack arm; rack box; one (1) model GS-474-100 independent oscillator head
(no dwells), oscillation speed range 8 – 188 cycles per minute (16 to 376
passes per minute); torch load capacity 5 lbs @ 6” (2.268 kgs @ 152.4 mm);
fine adjustment rack box with 12” (304.8 mm) long rack arm; GK-171-112
adaptor block; GK-190-076 oscillator gun holder assembly and mounting
brackets for mounting on the one end of a GK-171-047-4 36” (914.4 mm) long
rack arm. The Oscillator programmable microprocessor control is mounted in
the “KAT” Carriage with 4-turn potentiometer, on/off switch (capacity of control
to operate two (2) oscillator heads).
GS-474-041
Single Oscillator Head, No Dwell...........................................................................
Including one (1) model GS-474-100 oscillator head only. One (1) GK-171655 micro fine rack box; one (1) GK-190-076 oscillator gun holder assembly;
one (1) GK-171-650 standard rack box and all head mounting brackets and
hardware.
GK-197-O-104
*Required* Oscillator Head Control Cable Assembly, 48” Long. .......................
For Single Oscillator Package with control, see Page 26.
GK-198-002
Frame-type cable bracket assembly ..................................................................... $
OVERLAY HEAD MOUNTING
GK-171-650
GB-413-030
Heavy-Duty Rack Box (2 required) .............................................................
6” (152.4 mm) long with adjustable nylastic bearing plugs, for 1-1/2 (38 mm)
square clamps.
Roller Bearing Rack Box (1 required)
GK-171-047-1
12” (304.8 mm) long Heavy-Duty 1-1/8” (29 mm) Square Rack Arm (2 req.) ..... $
With rack and one end turned to 1-1/8” (29 mm) diameter.
GS-474-070
1-1/2” (38 mm) x 48” (1219 mm) Rack Arm (1 required)
OPTIONAL PARTS
GC-036
February 1, 2009
Oscillator Head Mount Package ........................................................................... $
- 34 -
“KAT TRACKER” - COMPACT SEAM TRACKER SYSTEM
For Operation on 115 Volts, Single Phase 50/60 HZ, A.C. Power Supply
PART NO.
WSG-1200
DESCRIPTION
PRICE
KAT Tracker Standard Duty Compact Seam Tracker System ............................ $
With electronic tack override and end plate detection capabilities, 55 lb. (25 kg)
vertical capacity.
Unit complete with:
Model WS-250 Control Box with 10 ft. (3048 mm) power cord; Model WS-250019 Motorized Cross Slide Assembly with hardened ground rods and ball
bearing bushings, 4” (101.6 mm) stroke, 2-direction up/down, in/out, with two
(2) 5 ft. (1.5 m) control cables; Model WS-250-005 Remote Control Pendant
with 6 ft. (2 m) control cable; Model WS-250-015 sensing probe with 6 ft (1829
mm) control cable; Probe Mount; Two (2) Manual Micro Slide providing ¾” (19
mm) in/out, up/down adjustment for sensing probe and gun holder; semiautomatic gun holder attachment providing 12” (305 mm) of horizontal and 6”
of vertical manual adjustment; set of mounting brackets for both cross slide
and control box for attachment to “KAT” carriage.
KAT Tracker Standard Duty Compact Seam Tracker System ............................ $
Same as above model WSG-1200, but with a 6” x 6” (152 x 152 mm) stroke,
SGD-115-CL-2 slide with ball bearing linear slide ways.
WSG-2200
KAT Tracker Heavy-Duty Seam Tracker System ................................................. $
With electronic tack override and end plate detection capabilities. 220 lbs.
(100 kg) vertical load capacity.
Unit complete with:
Model WS-250-032 Control Box with 10 ft. (3048 mm) power cord; Model WS250-029 Heavy duty motorized cross slide assembly with hardened ground
rods and ball bearing bushings, 6” (152 mm) stroke 2-direction up/down, in/out
with two (2) 5 ft. (1.5 m) control cable; Model WS-250-005 Remote Control
Pendant with 6 ft. (2 m) control cable; Model WS-250-031 sensing probe with 6
ft (1829 mm) control cable; probe mount; manual micro slide providing ¾” (19
mm) in/out, up/down, adjustment for sensing probe.
Cross Slide Lengths available up to 24” (609 mm) PRICE AVAILABLE UPON
REQUEST.
February 1, 2009
- 35 -
GULLCO HEAVY-DUTY “SAM” FRICTION DRIVE CARRIAGE
Using the Gullco 24 volt DC, GSP Control
For Operation on either 42 / 115 / 230 volts, single phase, 60 Hz AC Power Supply
Specify voltage when placing order.
PART NO.
DESCRIPTION
PRICE
GM-02-250
“SAM” Heavy Duty Friction Drive Carriage for mig welding ..............................
Friction drive heavy-duty travel carriage, with positive chain drive on four (4)
rubber tired wheels using a closed loop tack feedback for accurate speed
control.
Carriage controlled by the Gullco low voltage 24 volt GSP
microprocessor pulse width modulation motor control, all mounted in a remote
pendant control box attached to 8 ft. (243.84 cm) control cable and housing
the GSP control, interfacing with the forward/stop/reverse switch and infinitely
variable 4-turn speed potentiometer. LED display in IPM or cm/min. A manual
clutch enables free wheeling of carriage. Auxiliary wire feed start relay kit and
with a 17” x 22” aluminum plate providing a full flat surface for mounting
customer’s wire feeder.
GK-191-P-071
Additional Auxiliary Wire feed start relay kit........................................................ $
Including relay, circuit boards, mounting hardware, multi-pin connector with 15
ft. (4572 mm) of wire feed cable.
GM-02-275
“SAM” Heavy-Duty Friction Drive Carriage for Single Sub-Arc
Carriage specs as above, except no mounting plate, but complete with a
main mounting mast and handle assembly, mounting arm for one wire reel
(wire reel supplied by other), mast equipped with quick jaw clamp assembly;
flux hopper mounting arm with quick adjust clamp assembly; vertical and
horizontal manual 4” x 4” slides (hardened and ground rods with linear
bearings for ease of adjustment. Slides complete with arm and adjustable
mast clamp assembly; control support arm and adjustable mast clamp
assembly and one (1) set (two [2] adjustable guide roll arms).
GM-02-295
Same as above, except complete with Miller HDC 1500DX Control, wire
feeder, welding gun, wire wheel, flux hopper. (Power Source is not
included)................................................................................................................... $
GM-02-276
“SAM” Heavy Duty Friction Drive Carriage for twin sub-arc ..............................
As above, part no. GM-02-275 except having eight (8) wheels for stability and
two (2) mounting arms for two (2) wire reels.
GM-02-060
Carriage Steering Assembly .................................................................................. $
An optional device easily attaches to front of Carriage allowing the operator to
make steering corrections as necessary.
GM-02-043
Weld Joint Pointer Assembly................................................................................. $
An adjustable pointer, which attaches to the wire feed head to point to the weld
joint, to help the operator visualize where the sub-arc weld is being deposited.
February 1, 2009
- 36 -
**
GULLCO VARIABLE SPEED SIDE BEAM CARRIAGE
For Operation on either 42 / 115 / 230 volts, single phase, 60 Hz AC Power Supply
Specify Voltage when Placing Order
PART NO.
DESCRIPTION
PRICE
GK-199-H*-01
Gullco Variable Speed Side Beam Carriage .........................................................
With closed loop tack feed back for accurate speed control, regardless of load.
Maximum load 1,000 lbs. (453 kgs) at 3” (76.2 mm). The side beam carriage
is controlled by the Gullco low voltage 24 volt GSP microprocessor pulse width
modulation motor control interfaced with the forward/stop/reverse switch and
infinitely variable 4-turn speed potentiometer with LED display in IPM or
cm/min, limit switches and auto wire feed start.
GK-199-001
10 Ft. (3.048 m) length of precision side beam for the above Carriage.............
The side beam and track rack assembly is an all-steel fabrication designed to
provide accurate travel path for the side beam carriage.
WSG-2200
Gullco Heavy-Duty Seam Tracker
With 6” x 6” (152 x 152 mm) slides. Load capacity 165 lbs (74.82 kg).
GS-495-012
Side Beam Cross Slide Mount ...............................................................................
February 1, 2009
- 37 -
MODELS GP-200/300 STANDARD AND THROUGH HOLE POSITIONERS
For Operation on 42 / 115 / 230 volt, single phase, 50/60 Hz power supply
PART NO.
DESCRIPTION
PRICE
GP-200-M*
Standard Welding Positioner .................................................................................
Rotation speed infinitely variable 0.27 to 4.63 RPM; load capacity 150 lbs. (68
kgs) with table in vertical position; 300 lbs. (132 kgs) with table in horizontal
position. Drive by 24 volt DC gearhead motor with Gullco 24 volt DC
microprocessor electronic control. Positioner complete with remote control
providing infinitely variable speed rotation; forward/reverse switch; run/stop switch
and speed potentiometer. Table tilt manually set at any position through 90° with
positive lock. Positioner complete with mounting plate with tapped holes for
either a 12” (305 mm) round table with six (6) radial slots, or Gullco WPG-250
Gripper. Alternately, above table and gripper can be mounted together on the
Positioner mounting plate.
GP-300-M*
2” Through Hole Positioner (same as GP-200-M) except....................................
With 2” through hole.
GPP-200-M*
Standard Welding Positioner (same as GP-200-M) except .................................
Equipped with gas purge complete with rotary coupling attached to the drive
shaft assembly, having a ¼” (6.4 mm) hole through the center.
GP-200-H*
Standard Welding Positioner (same as GP-200-M) except .................................
Rotation speed infinitely variable 0.75 to 12.5 RPM.
GP-300-H*
2” Through Hole Positioner (same as GP-200-H) except ....................................
GPP-200-H*
Standard Welding Positioner (same as GP-200-H) except..................................
*See page 40 for Positioner Accessories.
February 1, 2009
- 38 -
MODELS GP-200/300 STANDARD AND THROUGH HOLE POSITIONER ACCESSORIES
PART NO.
DESCRIPTION
PRICE
WELDING POSITIONER - ACCESSORIES
GP-200-016
12” Diameter Aluminum round table.....................................................................
Complete with ‘T’ slots and mounting screws.
GP-300-002
12” Diameter Aluminum round table (used on GP-300 Positioner only)………..
Complete with ‘T’ slot and mounting screws.
WPG-250
3-Jaw Self-Centering Gripper................................................................................. $
Capacity .375” (9.52 mm) through 15” (381 mm) and mounting screws.
GP-200-024
On-Off Footswitch Assembly ................................................................................. $
GP-200-025
Variable Speed Foot Switch Assembly ................................................................. $
GP-200-023
Forward/Reverse Footswitch Assembly ...............................................................
February 1, 2009
- 39 -
MODELS GP-250 SERIES PROGRAMMABLE POSITIONERS
PART NO.
DESCRIPTION
PRICE
GP-250-M
Programmable Welding Positioner ....................................................................... $
Rotation speed infinitely variable 0.27 to 4.63 RPM load; capacity 150 lbs (68
kgs.) with table in vertical position; 300 lbs. (132 kgs) with table in horizontal
position.
Drive by 24 volt DC gearhead motor and Gullco 24 volt
microprocessor electronic control. Remote control with LED readout, infinitely
variable speed rotation, forward/reverse switch, run/stop switch and complete
with a programmable microprocessor providing adjustable positioning timing
cycles, amount of weld rotation, weld on/weld off through 360°. Plus an auxiliary
wire feed start relay with 15 ft. (4572 mm) wire feed cable. Positioner complete
with table tilt manually set at any position through 90° with positive lock.
Mounting plate with tapped holes for either a 12” (305 mm) round table with six
(6) radial slots, or a Gullco WPG-250 gripper. Alternately, above table and
gripper can be mounted together on the positioner mounting plate.
GP-350-M
2” Through Hole Positioner (same as GP-250-M) except....................................
GPP-250-M
Programmable Welding Positioner (same as GP-250-M) except........................ $
GP-250-H
Programmable Welding Positioner (same as GP-250-M) except........................ $
Rotation speed infinitely variable 0.75 to 12.5 RPM.
GP-350-H
2” Through Hole Positioner (same as GP-250-H) except ....................................
GPP-250-H
Programmable Welding Positioner (same as GP-250-H) except ........................
shaft assembly having a ¼” (6.4 mm) hole through the center.
ACCESSORIES FOR ABOVE
GP-200-016
12” Diameter Aluminum round table.....................................................................
GP-300-002
12” Diameter Aluminum round Table For GP-300 Positioner only) …………….$
WPG-250
3-Jaw Self-Centering Gripper................................................................................. $
Capacity .375” (9.52 mm) through 15” (381 mm) and mounting screws.
GP-200-024
On-Off Footswitch Assembly for Manual Operation ........................................... $
GK-191-P-071
Auxiliary wire feed start relay kit for a second wire feeder ................................ $
GP-175-030
Complete Welding Gun Positioning Package ......................................................
Including vertical and horizontal manual adjustment. Pneumatic gun
positioning slide with solenoid relay and support stand.
February 1, 2009
- 40 -
SELF-CENTERING GRIPPERS
PART NO.
DESCRIPTION
PRICE
WPG-250
Self-Centering Bolt-on Gripper .............................................................................. $
Capacity .375” (9.52 mm) through 15” (381 mm).
WP-400
Self-Centering Bolt-on Gripper .............................................................................. $
As above, capacity 3½” (88.9 mm) through 20” (508 mm)
February 1, 2009
- 41 -
PRICE LIST- EXPORT
KAMEL, PIPE TURNING ROLLS & TORCH SUPPORTS
For Operation on 42 / 115 / 230 Volt, Single Phase 50/60 HZ., A.C. Power Supply
PART NO.
DESCRIPTION
PRICE
KR-200-L*
Power Turning Roll ................................................................................................. $
Turning capacity 1,500 lbs. (680 kg). Load capacity 750 lbs. (340 kg).
Diameter range 2” to 16” (51 mm – 406 mm). Speed range 1-35.4 IPM (2.5 –
89.9 cm/min). Forward/stop/reverse switch, speed potentiometer, supplied
with stop/start footswitch on 10 ft. (3048 mm) of control cable.
KR-200-M*
Power Turning Roll ................................................................................................. $
Same as above except speed range 2.2 – 70.8 IPM (5.6 – 180 cm/min) and
turning capacity 1000 lbs. (454 kg).
KR-750
Idler Roll ..............................................................................................................
For either above models, 750 lbs. (340 kg) load capacity.
KR-1000-CSB
Free standing Torch Support 1-1/8” (29 mm) square .......................................... $
Providing 22” (866 mm) of vertical adjustment, 10-1/2” (266.7 mm) horizontal
adjustment with swivel mounted standard rack type cutting torch holder.
(Shown with cutting torch – not included)
KR-1000-WSB
Semi-Automatic Support Bracket 1-1/8” (29 mm) Square................................... $
Free standing gun support provides 22” (866 mm) vertical adjustment, 10-1/2”
(266.7 mm) horizontal adjustment. Complete with insulated semi-automatic
gun holder.
(Shown with welding gun – not included)
KR-2000-CSB
Free Standing Torch Support 1-1/2” (38 mm) Square .........................................
Providing 18” (709 mm) of vertical adjustment, 6-1/2” (165.1 mm) horizontal
adjustment with swivel mounted standard rack type cutting torch holder.
(Shown with cutting torch – not included)
KR-2000-WSB
Semi-Automatic Support Bracket 1-1/2” (38 mm) Square...................................
Free standing gun support provides 18” (709 mm) vertical adjustment, 6-1/2”
(165.1 mm) horizontal adjustment. Complete with insulated semi-automatic
gun holder.
(Shown with welding gun – not included)
February 1, 2009
- 42 -
KBM-18 PORTABLE PLATE EDGE BEVELLING MACHINE
WITH ADJUSTABLE BEVELLING HEAD
PART NO.
KBM-18-100
DESCRIPTION
PRICE
Portable Plate Edge Bevelling Machin
With adjustable bevelling head to produce bevel angles 22-1/2° through 55°.
Bevelling speed 120 IPM (305 cm/min). Bevelling produced by a rotary shear
type cutter ideal for beveling mild steel, stainless steel and aluminum plates
from ¼” to 1-1/2”* (6.0 – 38.1 mm*) thick with a maximum bevel width. 0.70”
(18 mm) at a standard bevel angle 30°. Machine supplied with a KBM-18-X1C
medium tooth cutter, angle bevel pins for 22-1/2°, 30°, 37-1/2°, 45° and 55°
degree bevels. All bevel angles are obtained by tilting the adjustable cutter
head assembly on its base frame. Machine complete with a 2 H.P. 3-phase
motor.
Voltages available: 230V, 460V and 575V, 3 phase 60 hz., and 380V, 415V, 3
phase, 50 hz. (Specify voltage at time of placing order).
Weight: 285 lbs. (129.2 kgs). – including undercarriage assembly.
*Thinner material can be bevelled – consult factory for details.
KBM-18-069
Self-aligning, spring loaded caster wheel assembly
for self-propelled operation (factory installed) ........................................................
KBM-18U
Inverted Portable Plate Edge Bevelling Machine.................................................
Complete with Undercarriage Assembly, for Bevelling the underside of plate.
KBM-18U-012
Air Jet Assembly (recommended for inverted beveller).......................................... $
KBM-18U-008
Conversion Kit.....................................................................................................
To convert KBM-18 Standard to a KBM-18U Inverted Beveller.
KBM-18-X1C
Medium Tooth Cutter ..............................................................................................
GBM-18-X1
Standard deep tooth cutter (medium cut).............................................................
Recommended for mild steel and aluminum
GBM-18-FXS
Heavy Duty shallow tooth cutter (fine cut) ........................................................... $
Recommended for stainless steel and high tensile steel.
GBM-18-(Degree) Angle Bevel Pins ...............................................................................................
For angles other than those supplied as standard with machine.
KBM-18-122
Narrow Width Clamp Roller Assembly .................................................................
GBM-18-015-A
Cutter Shims 0.019” (0.5 mm) ................................................................................ $
GBM-18-015-B
Cutter Shims 0.039” (1.0 mm) ................................................................................ $
February 1, 2009
- 43 -
KBM-28 PORTABLE PLATE EDGE BEVELLING MACHINE
WITH ADJUSTABLE BEVELLING HEAD
See Bulletin KBM-28-0106
PART NO.
KBM-28-100
DESCRIPTION
PRICE
Portable Plate Edge Bevelling Machine ................................................................
With adjustable bevelling head to produce bevel angles 22-1/2°, through 55°.
Bevelling speed 120 IPM (305 cm/min). Bevelling produced by a rotary shear
type cutter ideal for beveling mild steel, stainless steel and aluminum plates
from 5/16” to 2” (8 – 50 mm) thick with a maximum bevel width 1.10” (28 mm)
at a standard bevel angle 30°. Machine supplied with a KBM-28-X1C medium
tooth cutter, angle bevel pins for 22-1/2°, 30°, 37-1/2°, 45° and 55° degree
bevels. All bevel angles are obtained by tilting the adjustable cutter head
assembly on its base frame. Machine complete with a 3 h.p., 3 phase motor.
Voltages available: 230V, 460V and 575V, 3 phase 60 hz., and 380V, 415V, 3
phase, 50 hz. (Specify voltage at time of placing order).
KBM-28-080
Gullco exclusive hydraulic adjustable lift undercarriage with self-aligning spring
loaded. Caster wheel assemblies for self-propelled operation (installed) ...............
KBM-28-002
Gullco exclusive self-aligning, spring loaded caster wheel assembly for
self-propelled operation. *For fixed height application (installed)
KBM-28U
Inverted Portable Plate Edge Bevelling Machine.................................................
Complete with undercarriage assembly, for Bevelling the underside of Plate.
KBM-28U-018
Air Jet Assembly (recommended for inverted beveller).........................................
February 1, 2009
- 44 -
KBM-28 AND KBM-28U BEVELLER ACCESSORIES
PART NO.
DESCRIPTION
PRICE
KBM-28-X1C
Medium tooth cutter................................................................................................ $
GBM-28-X1
Standard deep tooth cutter (medium cut).............................................................
Recommended for mild steel and aluminum
GBM-28-FXS
Heavy Duty shallow tooth cutter (fine cut) ........................................................... $
Recommended for stainless steel and high tensile steel.
GBM-28-(Degree) Angle Bevel Pins ...............................................................................................
For angles other than those supplied as standard with machine.
KBM-28-078
Narrow Width Clamp Roller Attachment............................................................... $
GBM-28-015-A
Cutter Shims 0.019” (0.5 mm) ................................................................................ $
GBM-28-015-B
Cutter Shims 0.039” (1.0 mm) ................................................................................ $
CONVERSION PACKAGE
KBM-28-200
Conversion Package ............................................................................................... $
To convert KBM-28U Inverted machine to a KBM-28 Standard machine.
**
** - Consult Factory
February 1, 2009
- 45 -
PRICE LIST - EXPORT
ELECTRODE STABILIZING OVENS
PART NO.
DESCRIPTION
PRICE
10A-20
10lb. Portable Oven…………………………………………………………..
for 115 volt AC/DC power supply; no thermostat.
Average temperature 275° F (135° C).
10A-20-220
10 lb. Portable Oven, Same as above, but for 220 volt AC/DC ...........$
10B-20
10 lb. Portable Oven................................................................................$
for 115 volt power supply AC only, with thermostat.
Temperature 100-400° F. (38-205° C).
10B-20-220
10 lb. Portable Oven, Same as above but for 220 volt AC ..................$
50
50 lb. Portable Oven................................................................................$
for 115 volt AC only, with thermostat. Temperature 100-400° F (38-205° C).
50-220
50 lb. Portable Oven, same as above but for 220 volt .........................
125
125 lb. Stackable Oven ...........................................................................$
for 115 volt AC, with thermostat. Temperature 100-550° F (38-288° C).
125-220
125 lb. Stackable Oven same as above but for 220 volt AC ...............
350
350 lb. Stackable Oven ...........................................................................$
for 115 volt AC, with thermostat. Temperature 100-550° F (38-288° C).
350-220
350 lb. Stackable Oven same as above but for 220 volt AC ...............
350-H-B
350 lb. Stackable Oven 115 Volt AC ......................................................$
With thermostat. Temperature 100-650° F (38-343° C).
350-H-C
350 lb. Stackable Oven same as above but for 220 Volt AC ...............
1000
1000 lb. Floor Model Oven………………………………………………..
for 220 / 440 volt AC, with thermostat. Temperature 100-550° F (38-288° C).
1000HTIC
(GHTO-186)
1000 lb. Rebake Oven .............................................................................$
for 440 or 550 volt AC, 3-phase. Temperature 100-1000° F (38-538° C).
with indicating controller.
**
1000HTDP
1000. Rebake Oven..................................................................................$
for 440 or 550 volt AC, 3-phase. Temperature 100-1000° F (38-538° C)
with indicating controller and electronic digital programmer.
**
** Consult Factory
February 1, 2009
- 46 -
“FLUX HOLDING HOPPERS”
PART NO.
DESCRIPTION
PRICE
GOV-100-FH
100 lb. Flux Holding Hopper ..................................................................................
115 volt, 100-400° F (38-205° C) temperature, 400 watts, complete with
thermostat and thermometer.
GOV-100-PFD
100 lb. Portable Flux Holding Oven....................................................................... $
115 volt, 100-400° F (38-205° C) temperature, 400 watts complete with
thermostat, thermometer and shut-off valve. Supplied with portable truck and
filling bucket.
GOV-200-FD
200 lb. Flux Holding Oven ......................................................................................
115 volt, 100-550° F (38-288° C) temperature, 1500 watts, complete with
thermometer and thermostat.
GOV-600-FD3
600 lb. Flux Holding Oven ......................................................................................
Divided into three (3) compartments; 200 lbs. Each compartment.
Temperature range 100-550° F (38-288° C) 4500 watts for operation on either
220 volt or 440 volt. Complete with thermometers and three (3) individual
temperature controls. (Please specify voltage at time of placing order).
GOV-600-FDHT
600 lb. High Temperature Flux Oven..................................................................... $ **
Temperature range 100-850° F (38-455° C) 11,400 watts, with thermometers
and three (3) individual temperature controls. For operation on 220 / 440 / or
575 volt, 3-phase power supply. Please specify voltage at the time of placing
order).
** Consult Factory
February 1, 2009
- 47 -
DRY PAK ELECTRODE DISPENSER
PART NO.
DP-188-14
DESCRIPTION
PRICE
Dry Pak Extended Moisture Control Electrode Dispenser…………………$
For 14” (350 mm) electrodes. (Price for one)
Packaged – 12 Dry Pak to a Carton
PARTS
DP-188-05
Complete cap assembly with rubber seal……………………………………..$
DP-188-31
54” (1371 mm) belt, complete with buckle……………………………………..$
February 1, 2009
- 48 -
“KATBAK”
NON-METALLIC WELD BACKINGS
PART NO.
DESCRIPTION
Meters Per Carton
Price Per Metre
1G42-R
25 x 25 mm Tile 11 mm Groove, with knuckle joint ................ 12........................ $
**
Dimensions
A: ¼ in 6.3mm
B: 1in 25.4mm
C: 1in 25.4mm
D 9/32in 7.2mm
E: 7/16in 11.1mm
F: 1/16in 1.6mm
G: 3/16in 4.8mm
1G42-ER
25 x 25 mm Tile with small up-stands and knuckle joint ....... 12........................ $
**
1G42-GR
25 x 25 mm Tile 11 mm Groove, with knuckle joint, for AL.... 12........................ $
**
1G42-FR
25 x 25 mm Tile, Flat, no Groove .............................................. 12........................ $
**
Dimensions
A: 1/4in 6.3mm
B: 1in
25.4mm
C: 1in
25.4mm
D: 3/16in
4.8mm
1G43-R
25 x 25 mm Tile, 6 mm groove, with knuckle joint.................. 12........................ $
**
Dimensions
A: 1/4in 6.3mm
B:1in 25.4mm C:1in 25.4mm D: 3/8in 9.5mm
E: 1/4in 6.3mm F: 1/16in 1.6mm G: 3/16in 4.8mm
1G43-GR
25 x 25 mm Tile, 6 mm groove, with knuckle joint for AL ...... 12........................ $
**
1G82-R
25 x 30 mm Tile, 11 mm groove, with knuckle joint................ 9.......................... $
**
Dimensions
A: 5/16in 7.9mm
B:1/14in 31.7mm C:1in 25.4mm D: 13/32in 10.3mm
E: 7/16in 11.1mm F: 1/16in 1.6mm G: 3/16in 4.8mm
1G83-R
25 x 30 mm Tile, 6 mm groove, with knuckle joint.................. 9.......................... $
**
1G93-R
25 x 25 mm Tile, 12.5 mm groove, with knuckle joint............. 12........................ $
**
Dimensions
A: 1/4in 6.3mm
B:7/8 to 1in 22.2 to 25.4mm C:1in 25.4mm D: 5/32in 4mm
1G33-45
E: 1/16in 1.6mm F: 3/16in 4.8mm G:7/16in 11.1mm
25 mm x Triangular Ceramic for 45°......................................... 12........................ $
**
Dimensions
A: 9/16in 14.3mm
E: 55°
F: 85°
February 1, 2009
B: 5/8in 15.9mm
G: 1/8in 3.2mm
C: 1in 25.4mm
H: 7/64 2.8mm
- 49 -
D: 40°
I: 3/32in 2.4mm
“KATBAK”
NON-METALLIC WELD BACKINGS
PART NO.
DESCRIPTION
Meters Per Carton
Price Per Metre
1G33-60
**
Dimensions
A: 9/16in 14.3mm
E: 55°
F: 85°
B: 5/8in 15.9mm
G: 1/8in 3.2mm
C: 1in 25.4mm
H: 7/64 2.8mm
D: 40°
I: 3/32in 2.4mm
1G33-90
**
Dimensions
A: 9/16in 14.3mm
E: 55°
F: 85°
B: 5/8in 15.9mm
G: 1/8in 3.2mm
C: 1in 25.4mm
H: 7/64 2.8mm
D: 40°
I: 3/32in 2.4mm
1G6-RD
25 mm x 6 mm Round ................................................................ 12........................ $
**
1G-9-RD
25 mm x 9 mm Round ................................................................ 12........................ $
**
1G13-RD
25mm x 13 mm round ................................................................ 12........................ $
**
Dimensions
A: 1/2in
12.7mm
0.125-FG
0.250-FG
B:1in 25.4mm
25 mm Wide Glass Cloth
Heavy Duty Backing Tape for use up to 80 amps................... 25 m/roll............. $
**
25 mm Wide Glass Cloth
Heavy Duty Backing Tape for use up to 80 amps................... 12 m/roll............. $
**
** - Consult Factory
We manufacture over 100 different shapes and sizes of ceramic tile. The above are the most common.
If the ceramic tiles you require is not shown, please consult factory.
Minimum Order – One (1) carton
All Flat Tiles available in 1” x ¼” (25.4 x 6.35 mm)
All Flat Tiles available in metal trays.
February 1, 2009
- 50 -
PRICE LIST - EXPORT
CUTTERS – HARRIS TYPE
PART NO.
DESCRIPTION
PRICE
198-2R-35
2-Hose Acetylene Cutting Torch............................................................................ $
with 32 pitch rack. Barrel diameter 35 mm (1-3/8 in) x (10 in) long. Quick
action cutting oxygen lever and preheat trim valves. Capacity 0-200 mm (0-8
in).
198-2TR-35
3-Hose Acetylene Cutting Torch............................................................................ $
with 32 pitch rack. Barrel diameter 35 mm (1-2/8 in x 10 in) long. Quick action
cutting oxygen lever and preheat trim valves. Capacity 0-380 mm (0-15 in).
PROPANE
198-2FR-35
2-Hose Propane Cutting Torch .............................................................................. $
cutting oxygen lever and preheat trim valves. Capacity 0-200 mm (0 – 8 in).
198-2TFR-35
3-Hose Propane Cutting Torch .............................................................................. $
cutting oxygen lever and preheat trim valves. Capacity 0-380 mm (0-15 in).
TH-98
Adjustable Twin Tip Adaptor.................................................................................. $
For 2 simultaneous cuts from 1 torch. Widths 1.2 – 12 in (30 – 305 mm)
S-98-C
Adjustable Tip Adaptor...........................................................................................
For bevel cuts with torch remaining vertical.
E-9
Tip cleaners for VVC and VAX nozzles ................................................................. $
BV-98-2
Pre-heat attachment to assist on difficult bevel cuts for use on propane only
HOSE ADAPTORS
These adapt torches to accept standard U.K. 3/8 fitted gas hose. Adaptors are supplied with all torches and are included in the above price.
38-2GR
Right Hand (Oxygen)...............................................................................................
38-2GL
Left Hand (Fuel Gas) ...............................................................................................
NOTE:
When using adjustable tip adaptor S-98-C fit also Lifter Bracket
GK-190-066 to obtain adequate Torch Height Adjustment.
February 1, 2009
- 51 -
PRICE LIST - EXPORT
CUTTING NOZZLES - HARRIS TYPE
REFERENCE
THICKNESS (mm)
UNIT PRICE
ACETYLENE TYPE 6290 – VAX
1VAX
2VAX
3VAX
4VAX
5VAX
6VAX
8
15
35
75
150
-
8 ....................................................... $
15 ..................................................... $
36 ..................................................... $
75 ..................................................... $
150 ................................................... $
250 ................................................... $
31.00
31.00
31.00
31.00
31.00
31.00
PROPANE – TYPE 6290 VVC
5/0 VVC
4/0 VVC
3/0 VVC
2/0 VVC
0 VVC
0 ½ VVC
1 VVC
1 ½ VVC
2 VVC
2 ½ VVC
3 VVC
4 VVC
5 VVC
5 ½ VVC
4
6
9
12.5
20
35
60
75
125
150
175
200
225
-
4 ....................................................... $
6 ....................................................... $
9 ....................................................... $
12.5 .................................................. $
20 ..................................................... $
35 ..................................................... $
60 ..................................................... $
75 ..................................................... $
125 ................................................... $
150 ................................................... $
175 ................................................... $
200 ................................................... $
225 ................................................... $
250 ................................................... $
31.00
31.00
31.00
31.00
31.00
31.00
31.00
31.00
31.00
31.00
31.00
31.00
31.00
31.00
HEAVY DUTY - PROPANE
5NH
6NH
7NH
8NH
February 1, 2009
225
250
275
300
-
250 ................................................... $
275 ................................................... $
300 ................................................... $
350 ................................................... $
- 52 -
37.00
37.00
37.00
37.00

gullco international (uk) limited gullco international (uk

Transcription

Similar documents

How to make a saddle rack

Avrak Installation Instructions

Brochure AP-810-AH-T

The Carriage House - Houmas House Plantation and Gardens

Station display shows waiting commuters the best train

RackBuilder® Delivered - Milestone AV Technologies

Best properties on the market This week:Carriage house living

shipping logistics conditions of carriage

20 Inch Deep Rolling Series iSheet

welding and cutting automation