Pumps - Seattle Marine and Fishing Supply Co.

Transcription

277
Flexible Impeller Pedestal Pumps
JAB2760-0001
JAB6400-0004
Engine Cooling Pump & General Purpose Pumping
Pedestal mount, corrosion resistant bronze pumps:
Use for engine cooling, washdown, circulation, & general purposes
on-board or dockside.
• Bronze or stainless steel shaft installed with permanently lubricated ball
bearings for long life & heavy-duty service.
• Self-priming with ability to operate in either direction at variable speeds.
• Capacity ranges from 3 GPM to 83 GPM with varied port configurations
and sizes.
• Most models have replaceable cams/wearplates for extended product life.
• Removable end cover for easy impeller service.
• Standard impeller for these pump models is neoprene.
(some have alternative oil resistant nitrile impellers available.)
JAB7420-0004
JAB3890-9011
JAB18370-0000
Stock #
Description
JAB3890-9011 .......................11.3 GPM, 3/4" NIPT Port Connection,
5/8" Dia. shaft; lip seal. Weight 4 Lb.
JAB1210-0001 .......................Impeller for JAB3890-9011
JAB777-9001 .........................26 GPM, 1" NIPT Port Connections,
5/8" Dia.shaft, face seal, brass
cam & impeller insert. Weight 7 Lb.
JAB17937-0001 .....................Impeller for JAB777-9001
JAB6400-0004 .......................62 GPM, 1-1/4" NIPT Port,1" shaft,
face seal, brass cam &
impeller insert. Weight 11 Lb.
JAB17935-0001..................... Impeller for JAB6400-0004
JAB2760-0001 .......................3.7 GPM, 1/4" NIPT Port Connections.
3/8" Dia. shaft, lip seal. Weight 1.5 Lb.
JAB7420-0004 .......................62 GPM, 1-1/4" NIPT Port, 1" shaft,
face seal, brass cam &
impeller insert. Weight 11 Lb.
Stock #
Description
JAB1673-1001 .......................11.3 GPM 1/2" NIPT Port Connections,
5/8" Dia. shaft, lip seal. Weight 4 Lb.
Plain Bearing Bronze Pump
Economical plain bearing bronze pumps.
Simple & economical to service. Wide variety
of bilge pumping, washdowns, engine cooling,
circulation or dockside pumping needs with capacities
of 11 GPM. Weight. 3.5 Lb
• Bronze pump body & stainless steel shaft resist corrosion.
• Packing type with grease cup lubrication & replaceable cam.
• Equipped with oil resistant nitrile impeller.
1/2" NIPT Port Connections, 5/8" Dia. Shaft; 1/2 HP at 1750 RPM.
Stock #
Description
JAB4560-0001 .......................Bronze Pump
Pumps & Plumbing
JAB777-9001
JAB1673-1001
JAB18370-0000 .....................83 GPM, 2" NIPT port connections,
1" Dia. shaft, face seal. Weight 17 Lb.
Jabsco Vertical Port Pump
Benefits of flexible impeller pumps in a mid-size
package with substantial flow rate & vertically
oriented ports.
• Self priming to 10ft vertical lift.
• Mechanical face seal, double row ball bearing.
• Neoprene impeller fitted as standard.
1 " NPT, 7" Long x 4-1/4" W x 4" High. 7 Lbs.
Stock #
Description
JAB5330-9001 .......Pump 1” Vert Port Engine 2/3 Cam
General Purpose Pump
• Bronze body. Stainless steel shaft.
• Stainless steel lip or mechanical seals for shaft.
• Shielded ball bearings. 1" IPT.
Stock #
Description
JAB777-0001 .........Pump w/Neoprene Impeller
JAB777-0003 .........Pump w/Nitrile Impeller
JAB777-9001 .........Pump w/Neoprene Impeller
JAB777-9003 .........Pump w/Nitrile Impeller
Call Toll Free: (800) 426-2783 8-5 M-F
Website: http://www.seamar.com
Seattle: (206) 285-5010 Fax: (206) 285-7925
email: seamar@seamar.com
278
Clutch Pumps
Flexible Impeller Clutch Pumps
Pumps & Plumbing
Clutch pumps combine:
Unique advantages of self-priming flexible impeller Jabsco pump & a
clutch-drive mechanism to engage or disengage pump as needed.
Available with either manual or electric clutches for use versatility.
Generally they are powered by propulsion engines but may be driven
by any adequate source of belt drive power.
Clutch will "free wheel" with power source until pump is required.
Then, clutch can be engaged to throw pump into operation for emergency or general circulation needs.
Port sizes from 1"- 2" NPT & offer flow rates of 26 gallons per
minute to 83 gallons per minute.
All clutch pumps are built with bronze pump bodies & rotarymechanical face seals for long life in heavy duty marine uses.
Equipped with replaceable brass cam/wearplate to prolong service.
Removable end cover for easy impeller replacement without having
to remove plumbing or drive belt.
Ideal for bilge pumping, live-well circulation, deck wash-down
& many commercial or pleasure boat general pumping needs.
Electric Clutch Pumps
Electromagnetic clutch pumps equipped with a powerful electric clutch for convenient remote operation.
Each size pump is available in either 12, 24, or 32 volt models.
Capable of operating through a wide range of speeds and in either rotational direction.
Stock #
DC
Volt
Pulley
Belt
Grooves
Port
Size
NIPT
GPM
Impeller
RPM
Speed
Range
Wt.(lb)
JAB11860-0005 .....12............2A...........1..............26............920-0003
JAB11860-0045 .....12............1B ...........1..............26............920-0003
400-3000
400-3000
15.5
15.5
JAB11870-0005 .....12............2A...........1 1/4 ........62............836-0003
JAB11870-0045 .....12............1B ...........1 1/4 ........62............836-0003
JAB11870-0007 .....32............2A...........1 1/4 ........62............836-0003
400-2200
400-2200
400-2200
21
JAB18330-0000 .....12............2A...........2..............83............6760-0003
400-2200
31
18330
21
11860
Manual Clutch Pumps
Similar to electromagnetic clutch pumps but are equipped with a mechanically activated clutch.
Although operator is required to go below to put pump into service, they provide added
security of operation in event of an electrical power failure.
Stock #
Port
Size
IPT
GPM
RPM
Speed
Range
Impeller
JAB51080-9013 .....1..............26............920-0003 ................400-3000
JAB6590-0005 .......1-1/4........62............836-0003 ................400-3000
Weight.
10
Lb.
16-1/2 Lb.
Neoprene Impeller
Impeller Diameter 3-1/4"..... 9 Blades.
Shaft Diameter: 1"....Depth: 2-1/2".
Stock #
JAB836-0001
JAB836-0003
Call Toll Free: (800) 426-2783 8-5 M-F
Description
Impeller Neoprene
Impeller Nitrile
Seattle: (206) 285-5010 Fax: (206) 285-7925
279
Engine Cooling Pumps
Engine Cooling Pumps
All bronze body, bearing housing, & stainless steel shaft to withstand harsh
marine environments. Can directly replace some Sherwood models.
Stock #
Description
Port Size
Model #
Model #
18830-0000
G-30-2
1"
Chris Craft, 350C.l.
18830-1020
G-30-2
1"
Commander Marine 302, 351C.l.
Glaston 302, 351 C.l. 165, 190, 200, 225
18840-1010
G-21
1"
Nissan LDM 4 Cyl
18930-0000
G-45-1
1 1/4"
Chris Craft
Engine Cooling Pump
Flange mounted, flexible impeller (F series).
Features:
Bronze body, flexible neoprene impeller with 1"
NPT
Stock #
Pumps & Plumbing
JAB18830-0000 .....Engine Cooling Pump 1” or 1 1/4"......with Pulley Adaptor
JAB18830-0010 .....Engine Cooling Pump 1” or 1 1/4"......with Pulley
JAB18830-1020 .....Engine Cooling Pump 1” or 1 1/4"......with Keyed Shaft
Uses JAB1210-0001 Impeller
Replacement Pumps for other Engines:
Jabsco
Sherwood
Port Engine Application
Description
JNP10243491 .........Pump F7B-9 Engine Cooling
Lehman 302, 351C.l.
Powerhouse Marine 302, 351C.l.
Mercruiser-Type Pump Replacement
MerCruiser engines can replace their stock cast-iron, plastic
& aluminum composite water pump (Quicksilver #46-72774A32) with ITT Jabsco model built of bronze & stainless steel to
withstand harsh, corrosive marine environments.
• 1-piece body makes occasional impeller or seal
replacement quick & easy.
Includes replaceable cam & wearplate so pump can be
totally overhauled to like-new condition.
Replacement Impeller-Jabsco
Jabsco MerCruiser impeller directly replaces standard
impeller (Quicksilver # 47-59362) in MerCruiser
belt-driven engine cooling pumps.
• Made of long-life neoprene for max endurance &
performance, ensures abundant cooling water at all
engine speeds.
• Packaged with all gaskets for stock MerCruiser or Jabsco
replacement pumps. Convenient way to carry a spare.
Stock #
Stock #
Description
JAB43210-0001 .....................MerCruiser-Type Engine
Description
JAB17954-0001 .....Replacement Impeller
Jabsco 50410 Series
Retrofits crank driven pumps on Volvo, Indmar, & Marine Power
marine engines & utilizing the Chevrolet & Ford small & big
block engines whether the stock pump is Jabsco 22740-Series
or Johnson pump type F5B-9 or F6B-9.
• Volvo pump No. 855722 on small block engines is replaced
by Jabsco 50410-1251 half cam model.
• Volvo pump No. 85613 on big block engines is replaced
by Jabsco 50410-1201 full cam model.
• Chevrolet & Ford marinized engines equipped with Johnson pumps,
Jabsco model 50410-1201 full cam pump replaces Johnson model F6B-9.
When Replacing: Jabsco pumps
• 22740-Series ( with aluminum bearing housing).
• 23800-Series ( with cast iron bearing housing).
It is necessary to replace the three 2 3/4" long socket cap-head screws
(studs in early model engines) that secure pump to vibration dampener
with 3/8 - 24 x 3/4" long cap-head screws.
Crusader-Type Pump
ITT Jabsco now offers:
• Replacement engine cooling pump for most models of
popular Crusader (Thermo Electron) gas V-8 engines.
• Jabsco pump designed for easy & economical service
if ever required.
• Shaft seal can be replaced without removing pump shaft.
• Impeller bore has replaceable wearplate & stamped brass
end cover is economical to replace.
• Impeller fits either stock Crusader pump (replace impeller #
20300) or upgraded Jabsco model.
Stock #
Stock #
Description
JAB50410-1251 .....Volvo Engine Cooling Pump, 305 and 350 Chev
JAB50410-1201 .....Volvo Engine Cooling Pump MP, 454 Chev
Call Toll Free: (800) 426-2783 8-5 M-F
Description
JAB42730-0000 .....Crusader-Type Pump
JAB18948-0001 .....Replacement Impeller
Seattle: (206) 285-5010 Fax: (206) 285-7925
280
Impeller Cross Reference / Centrifugal Pumps
Pumps & Plumbing
Centrifugal Pumps
Centrifugal Pumps
One of the quietest pumps available.
Suitable for uses like bait tank circulation for extended periods of time.
Has the ability to adjust or stop flow as needed.
Centrifugal Pumps: Not self-priming & should be installed below the
source so there is a flooded situation at the inlet port.
• Limited pressure capacity; to ensure maximum flow, it is advisable
to keep total system restrictions to a minimum.
Centrifugal Puppy:
Use as a livewell circulator or diesel fuel transfer pump.
• May be installed directly on seacock & thru-hull fitting or
further along the piping system.
• Intake & outlet ports have 3/4" internal pipe thread.
• Pump head: all bronze build with open non-clog impeller design.
• Standard seal is a Viton compound for use versatility.
• Pump must be installed so motor is in a dry location.
• Meets: U.S. Coast Guard Electrical Regs.
(Title 33, Chapter 1, Part 183, Subpart 1).
Jabsco Cyclone Centrifugal Pumps
Long life circulation, high efficiency & flow.
Use for hot & cold water systems, livewell & bait tank
systems, liquid transfer also windscreen washing.
3/4 " NPT or BPS. 6" Long x 6-1/2" W x 5" High, 15 Lbs.
50870- 3/4 "NPT or BPS. 9" Long x 4-1/2" W x 5" High, 23 Lbs.
Stock #
Description
115 Vac Pump:
Ideal for many general dockside pumping needs.
Suitable for onboard uses like livewell or bait tank circulation.
• Pump head is same as Centri Puppy, but mounted on a continuous
duty 115 Vac motor thermal that is overload protected.
Groco Submersible Centrifugal Pump
Silent running pump is simple to service and operate.
Will handle small solids without pump damage.
• Provide high GPM flow but relatively low pressure.
• Centrifugals will not self-prime, a flooded inlet is required.
• Mount bracket allows 360 rotation.
• Inlet is threaded for 3/4" NPT.
• Outlet externally threaded for garden hose & internally for 1/2" NPT.
Stock #
Description
GRCCP20S12V .....Pump Submersible Centrif 12V
JAB50840-0012 .....Cyclone Pump Centrifugal 12V
JAB50830-0024 .....Cyclone Pump Centrifugal 24V
JAB50870-0012 .....Cyclone Pump Hi Pressure 12V
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
281
Flexible Impeller DC Motor Pump Units
Water Puppy Pumps
"Water Puppy"
A standard of excellence for low voltage DC self-priming motor
driven pumps. Full range of flexible impeller puppy type pumps.
Choose from the "Mini Puppy" to the "Commercial Duty Water Puppy"
for nearly any flow rate or use requirement.
Some pumps are reversible so they can change flow direction at
the flip of a switch.
• Self-priming puppy pumps may be located above fluid source
& installed in a convenient location, mounted in any position.
• Able to lift water up to 4 ft. bronze pump heads resistant to
corrosive marine environments for extended service.
• Removable end cover for easy impeller replacement without
disconnecting the plumbing.
Stock #
Volt
DC
Amp
Draw
Fuse/
Breaker
GPM/
LPM
Reversible
JAB8860-0001 .......12............4..............10............1.8......Yes
JAB18620-0003 .....12............5..............7..............1.8......Yes
IN
JAB18620-0003
JAB8860-0001
Ports
OUT
3/8 NPT GHT
3/8 NPT GHT
Weight (lbs.)
Impeller
Pumps & Plumbing
Mini Puppy
Smallest of Puppy Series with flow rate of about 2 gallons per minute.
• Uses same motor & similar quality components as Standard Water Puppy.
• Reversible Mini Puppy includes an integral on-off reversing switch to change
direction of flow.
Size
JAB14750-0001......4-1/2.....3-3/8" H x 4" W x 6-3/8" L
JAB14750-0003......5-1/2.....3-3/8" H x 4-3/4" W x 8-5/8" L
Water Puppy
Can deliver almost 7 gallons per minute at open flow. Equipped with pressure cast bronze body.
Features:
• Reusable O-ring type end cover seal.
• Ports: 1/2" internal pipe thread & 1" external hose barb.
• Included: 2 port adaptors to connect common garden hose.
• Fittings 3-3/8" H x 4-3/4" W x 6-3/8" L. (Commercial use)
Stock #
Volt
Amp
Fuse/
GPM/
DC
Draw
Breaker
LPM
Port
Reversible
JAB18660-0121 .....12............6.8...........15............6.3 (23 LPM )
�
JAB18660-0123 .....12............6.8...........15............6.3 ( 13 LPM )
�
IN
Impeller
OUT
Weight
No
1/2" NPT 1" Hose
JAB6303-0001
8 Lbs.
No
1/2" NPT 1" Hose
JAB6303-0003
8 Lbs.
Commercial Duty Water Puppy
Uses same pressure cast pump head but offers increased flow & durability to meet demands
of commercial & workboat applications.
Features high speed long-life motor with ball type shaft bearings.
Fittings: 3-3/8" H x 4-3/4" W x 7-1/8" L.
Stock #
Volt
Amp
Fuse/
GPM/
DC
Draw
Breaker
LPM
Port
Reversible
JAB18670-0123 .....12............9..............15............7.8...........Yes
JAB18670-0943 .....24............5..............10............7.8...........Yes
IN
OUT
1/2 NPT 1"hose
1/2 NPT 1"hose
Impeller
JAB6303-0003
JAB6303-0003
Weight
5-1/2 Lbs.
5-1/2 Lbs.
Puppy Pump Application Guide
Flexible Impeller Type Pumps
• Water Puppy
• Commercial Duty Water Puppy
• Mini-Puppy
• Reversible Mini-Puppy
Features:
• Excellent primeability, can pass small
solids without damaging pump, & some
models can reverse to change direction
of flow.
• Bilge pumping, bait tank circulation, deck
wash & windshield washers.
Call Toll Free: (800) 426-2783 8-5 M-F
Centrifugal Pump
Centri-Puppy is extremely quiet:
• Can pass small solids, & can pump against
restrictive plumbing without overloading motor.
• Ideal for bait tank circulation or livewell aerators.
• Centri-Puppy, however, is not self-priming so
it must be installed below the liquid source.
Sliding Vane Pumps
Vane Puppy & Reversible Vane Puppy
• Self-priming with 2 feet of tilt with vectra
color & vanes which are not affected by
oil or diesel fuel.
• Vane Puppies are especially suitable for
engine oil changing & diesel fuel transfer
uses.
• Reversible Vane Puppy has integral
on/off-reversing switch to pump dirty oil
out of an engine & clean oil back in.
Seattle: (206) 285-5010 Fax: (206) 285-7925
282
Vane Pumps
Self-priming Rotary Vane Pumps:
Pumps & Plumbing
Pumps are a positive displacement design with an off-center eccentric
rotor whose vanes slide inward & outward, as they move from top
to bottom of the bore; this action creates a vacuum to pull liquid
into the pump.
• Designed for diesel fuel & lightweight oils.
• Do not pump liquid containing solids or debris.
• Several models available with low voltage DC or 115 volt AC
motors.
• Low voltage model with integral on-off reversible switch to change
flow direction is available.
DC Vane Puppy
Vane Puppy operates by the rotary sliding vane principle.
• Has vectra rotor & vanes that are designed to handle oil or diesel fuel transfer.
• Pumps up to 5-1/2 GPM & transfers diesel fuel from a 55 gallon drum in 10 minutes.
• Self-priming to 3 feet. Low amp draw.
• Vane Puppies are equipped with a high torque motor with ball type shaft bearings.
• Rated for continuous duty operation. Bronze pump has ports with 1/2" internal pump thread.
• 1" external hose barb. Also supplied are port adaptors for 3/4" gallon hose thread.
Stock #
GPM
/LPM
Volt
DC
Amp
Draw
Fuse/
Brkr.
Reversible
JAB18680-0920 .....15.5/21 ...12............8..............15............Yes
Int.
Port
Dimensions- inches
Ext.
H
1/2 NPT 1" Hose 3-3/8
W
4-3/4
DC Reversible Vane Puppy
Many of the same features as Standard Vane Puppy but includes an integral 3-way switch to
reverse the direction of flow. Ideal for changing engine oil.
• With a valved manifold system, a single pump can be used to change oil in several engines.
• After pumping the old oil out, the pump can be reversed to pump the new oil in.
• Capacity of 5 GPM and suction lift of up to 3 ft.
• Ports have 1/2" internal pipe threads & 1" external hose barb.
• For duty cycles up to 30 minutes.
• Vane Puppy & Reversible Vane Puppy: Meet U.S. Coast Guard Electrical Regs.
Stock #
GPM
LPM
Volt
DC
Amp
Draw
Fuse/
Brkr.
Reversible
JAB18680-1000 .....5/19 .........12............8..............10............Yes
Int.
Ports
1/2 Npt
Ext.
1"Hose
115 Volt AC Vane Pump
Uses: Transferring diesel fuel or pumping light oil.
• Vectra rotor & vanes are not affected by petroleum products;
pump head is corrosion-resistant bronze.
• Self-priming up to 5 ft. and delivers up to 8 1/2 GPM.
• Empties a 55 gallon drum in less than 7 minutes.
• Ports: 1/2" internal pipe threads, 1" external hose barb,
includes 3/4" external garden hose adaptors.
• High speed motor is thermally protected, complete with 6 ft. power cord.
• Height 5-3/4"/Width 5-5/8"/Length 9-1/2"/Weight 14-1/2 lb.
Stock #
GPM
Volt
AC
Amp
Draw
Fuse/
Brkr.
Reversible
JAB18685-0000 .....8-1/2........115 ..........N/A.........N/A.........No
Ports
Int.
Dimensions- inches
Ext.
H
3 3/8"
Dimensions
H
1/2" NPT 1" Hose 5-3/4"
L
Weight
7-1/8
Weight
W
L
W
L
4 3/4"
5-5/8"
8 5/8"
9-1/2"
Lb.
5-1/2
Lb.
5 1/2"
Weight
Lb.
14-1/2 Lb.
Sliding Vane Diesel Pump VR050
Continuously rated diesel pump - 13.7 GPM at 10 ft. total head.
• Self priming up to 9.6 ft. vertical lift.
• Optional fitted switch, fuse & ports.
• 22° F to 104° F operating temp range.
Stock #
Description
Port
Int.
Ext.
Dimensions- inches
H
JABVRO50-1022....Diesel Fuel Trns 12V 1" 1" Hose 5-1/4"
JABVRO50-1122 ...Diesel Refueling 24V 1" 1" Hose 5-1/4"
Call Toll Free: (800) 426-2783 8-5 M-F
W
5"
5"
L
8-1/2"
8-1/2"
Weight
11 Lbs.
11 Lbs.
Seattle: (206) 285-5010 Fax: (206) 285-7925
283
Flexible Impeller AC Motor Pump Units
JAB12210-0001
JAB6050-0003
GPM
• 6050-0003 & 11810-Series pumps: Accepts optional 4732-0000
vacuum switch to auto shut-off pump while unattended & prevent dry
running.
• 12210-Series pumps: most compact of AC motor pump units.
They are capable of delivering up to 3-1/2 GPM.
Motor has replaceable brushes for extended life.
They are not rated for continuous duty operation.
• 12520-Series and 11810-Series pumps:
Midrange models that deliver about 6 GPM.
• 11810-Series: replaceable wearplate to extend service when
handling abrasive fluids.
• 6050-0003 pump: largest of motor pump units. A capacity of
26 GPM, best for larger de-watering or washdown uses.
Motor can be wired for either: 115 volt or 230 volt operation.
Motor
Duty
Port
Voltage
HP
Cycle
JAB12520-1001
Dimensions
Ext.
H
W
L
Weight
JAB6050-0003 .......26............115/230...3/4 ODP..Cont. .......1 NIPT
-
8-3/8
8
13-1/8
35-1/2 Lbs.
JAB6050-0013 .......26............115/230...3/4 TEFC Cont. .......1 NIPT
Impeller: JAB6056-0003(OR)
-
8-3/8
8
13-1/8
35-1/2 Lbs.
JAB11810-0003 .....9.5...........115 ..........1/3 ..........Cont. .......1/2 NIPT GHT
Impeller: JAB5929-0003 (OR)
7-3/4
7 1/4
10-1/2
22 Lbs.
JAB12210-0001 .....3.4...........115 ..........1/12 .........Int. ..........3/8 NIPT GHT
Impeller: JAB14750-0001 (N)
3-1/2
5
6-7/8
5 Lbs.
JAB12210-0003 .....3.4...........115 ..........1/12 .........Int. ..........3/8 NIPT GHT
Impeller: JAB14750-0003 (OR)
3-1/2
5
6-7/8
5 Lbs.
Stock #
Int.
Pumps & Plumbing
Jabsco Bronze AC Motor Pump units:
• Are similar to popular Puppy pumps but are equipped
with AC electric motors.
• Dockside general purpose pumping & some onboard uses.
• With 4 models: offering flows from 3-1/2 to 26 GPM,
pumps suitable for almost any de-watering, washdown or
circulation use.
• Self-priming & portable, very versatile.
• All pump heads are built of bronze materials for corrosion
resistance in marine environments.
• Removable end cover allows easy impeller service without
need to disconnect plumbing.
• All models are equipped with thermal overload protected motors
for operating safely; & have a 6 Ft. grounded power cord.
Jabsco 18610 Series Utility Pump
Very versatile pump. Moderate flow rate, portable, self-priming,
suitable for continuous duty. 5.8 GPM at 10 foot head.
• Bronze pump head, thermal overload protection,
• 8 ft. power cord with grounded plug & carrying handle.
Fitting:
1/2" NPT internal thread 1" hose
9" long x 5-1/2" wide x 7-1/16" high
Stock #
Description
Weight
JAB18610-0001 .....Pump 115vac Utility Neo Imp.....12 Lbs.
JAB18610-0003 .....Pump 115vac Utlity Nitrile Imp...12 Lbs.
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
284
Hydraulic Pumps
Hydraulic Washdowns
Reversible: 1-1/4” pump.
Parts:
Hydraulic Washdowns
Reversible: 2” pump.
Parts:
Stock #
Stock #
Description
Pumps & Plumbing
JAB6400-0004 .......1-1/4” Jabsco Pump
FBF0082 ................Mount
SPE26707DAV.......Hyd. Motor 1.24 Displ.
LOVL1001000 .......Hub 1” Shaft
LOVL100SPIDER .Spider for L099 or 100
Description
JAB18370-0000 .....2” Jabsco Pump
FBF0082 ................Mount
SPE40MH18 ..........Hyd.Motor 1.80 Displ.
LOVL1001000 .......Hub 1” Shaft
LOVL100SPIDER .Spider for L099 or 100
Model 6400-0000
Table Note: Progressively longer life may be expected as operating pressures and speeds are reduced.
Factory application engineering assistance is suggested for operation in shaded area.
High starting torque motors are required. Pump starting torque in dry condition
(no fluid in pump body) is 134 inch-lbs., wet condition is 105 inch-lbs..
Table shows approximate head-flow for new pumps in US gallons per minute and litres per minute.
Pacer Parts
For S pump.
Stock #
Description
PCRP58-0014 ........Repair Kit For S Pump
PCRP58-0702 ........Volute For 2” S Pump
PCRP58-0706 ........Impeller 2” S Pump 5vanE
PCRP58-0714 ........Ceramic Shaft SeaL
PCRP58-0723 ........Lower Drain Plug
PCRP58-0755 ........Body 3” Blk 30b
PCRP58-0977 ........Volute For 3” S Pump
PCR58-0975...........Impeller 3” S Pump 4vane
PCR58-1011 ...........Motor Mounting Bracket
Call Toll Free: (800) 426-2783 8-5 M-F
Pacer "S" Pump
With hydraulic motor or pedestal mount.
Stock #
Description
PCRSE2IBPE.........Pump 2" S Pedestal Mount
PCRSE2IBHYC .....Pump 2" S w/Hyd Drive
PCRSE3LBHYC ....Pump 3" S w/Hyd Drive
Seattle: (206) 285-5010 Fax: (206) 285-7925
General Purpose Pumps
Oil Drain Pumps
Stock #
Description
JAB34060-0130 .....Oil Drain Pump
Stock #
Description
JAB18080-0000 .....Oil Drain Hose Kit
Economy Oil Changer
Will extract 50 Wt. oil at temp of 70° through engines dip
stick tube in less than 5 minutes.
14 quart reservoir is supplied with heavy-duty professional oil
changer so 2 typical V-8 engines can be serviced on 1 trip
to the boat. 12-3/4" Dia.x 12-3/4" High.....5 Lbs.
Stock#
285
Pumps & Plumbing
Marine Engine Oil Drain Pump
Connects to current marine engine oil dipstick tube
on OMC, MerCruiser, & other marine engines with
threaded male garden hose fitting on the engine dipstick tube.
• Unique design allows one hand pumping for quick and
easy oil draining.
Includes pump with 3/4" brass fitting and
drain hose 1/2" x 2'. Weight, 1 lb.
Permanent Oil Drain Hose & Fitting
Assembly includes drain plug fitting, oil drain hose,
and cap/hose hanger clamp.
Oil drain kit: use in conjunction with
Jabsco drill pump, model 17215-0000, or
PAR hand pump, model 34060-0010.
• Drain plug fitting size is 1/2"- 20".
• Packed in poly bag with display header card.
• Not recommended for autos withdrain plugs exposed
to potential road hazard damage. Weight, 1 lb.
Description
JAB17850-0012 .....Oil Changer Economy 12V with Pail
JAB17850-1012 .....Oil Changer 12V New Diaphrarm
Flat Tank Oil Changer
Extracts 50 Wt. oil at temp of 70° through engines dip stick
tube in less than 5 minutes. 14 quart flat tank makes a clean
and simple oil change & disposal. Easy carry design. 12volt.
19" H x 12" W x 6.5 Deep........9 Lbs.
Stock #
Description
JAB17860-0012 .....................Flat Tank Oil Changer
Oil Change Pump
Same pump used in Jabsco multi-engine oil change
system. Can change oil in a typical V-8 in minutes.
3/8" NPT male threaded....7-1/8"L x 3-3/4" W.....9 Lbs.
Stock #
Description
JAB17830-0012 .....Oil Changer 12V Reversible
"Porta Quick" Oil Changer
Quick, easy & clean oil changes at flip of a switch.
• Removes oil/sludge through dip stick tube so engine oil changes quick/easy. No spill under engine.
• Oil changer supplied with both 1/4" x 40" dipstick probe and a female garden hose connector that
attaches suction hose directly to dipstick tubes supplied w/male garden hose threads.
• Reversible pump so container is emptied neatly/easily by reversing flow direction.
• Retractable pouring spout if not desirable to use pump for emptying.
• 12 volt model with 8' cord and alligator clips.
• Simply connect power cord to appropriate electrical source.
• With flick of switch sturdy motor pump unit drains crankcase into it's 14 qt. holding container.
Dimensions: Weight 9 Lb , Height 13-5/8", Width 13-1/2".
Stock #
Description
JAB17800-2000 .....12 V DC with Pail
JAB18620-0003......12V DC Pump Only Rev.
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
Pumps & Plumbing
286
Jabsco Water System Pumps
PAR 36950-Series
Popular premium pump for boats with up to 4 outlets.
Dependable, low maintenance pump able to run dry for extended periods.
Features:
• Smooth belt drive & flexible mounts aid in noise reduction.
• Pump is protected against city water pressure by a built-in check valve.
• Pulsation dampeners absorb water hammer & give smooth flow to fixtures.
• Low amperage motors conserve battery power. Ports fit 1/2" - 5/8" hose.
• Use in salt water systems for deck & anchor washdown, & galley rinse water.
Open flow
Stock #
Amps/
GPM
Volts
Dimensions (inches)
Fuse size
Height
Wt.
Width
JAB36950-2000 .....3.0...........12............6/8 ..........8-1/2 .......5-9/16
Length
6-9/16
(lbs)
10
PAR 36800-Series
Specific design supplies reliable, smooth, steady water flow on boats with 3 to 4 water fixtures.
Features:
• Run dry capability. Belt drive & flexible mounts for low noise.
• Built-in check valve protection against city water pressure.
• Automatic switch maintains 39 PSI pressure.
• Pulsation dampeners to absorb water hammer.
• Battery conserving low amperage motors & ports sized to take 1/2"-5/8" ID hose.
• Salt water system compatible for galley rinse water & anchor washdown.
Open flow
Stock #
Amps/
GPM
Volts
Dimensions (inches)
Fuse size
Height
Wt.
Width
JAB36800-1000 .....3.3...........12............6/8 ..........8-1/4 .......5-1/2
Length
8-5/16
(lbs)
11
PAR 36900-Series
Established & service proven pump for larger boats with up to 5 fixtures.
Features:
• Noise reducing belt drive and flexible mounts.
• Water hammer absorbing pulsation dampeners for smooth flow.
• Built-in check valve protection against city water pressure.
• Automatic switch maintains 39 PSI pressure. Low maintenance. Run dry capability.
• Low amp motor conserves battery. Ports fit 1/2" - 5/8" ID hose.
• Can be used in salt water systems for galley rinse water & deck & anchor washdown.
Open flow
Stock #
Amps/
GPM
Volts
Dimensions (inches)
Fuse size
Height
Wt.
Width
JAB36900-1000 .....4.2...........12............7.5/10 .....10-1/4 .....5-1/2
Length
(lbs)
Length
Weight.
8-5/16
12
PAR Light Duty Bilge Pumps
Inexpensive yet has performance & features of higher priced
pumps. Self-priming allows pump to be mounted above bilge &
sump areas with only the intake hose in bilge. Pump features a
tough plastic body & ports for 3/4" hose.
Stock#
Volts
Amps /
Fuse size
Flow
(GPM)
Dimensions
Height
Width
JAB36960-2000 .....12............6 - 6 1/4...4..............7 1/4".......4 1/16"
High Pressure Switch
Stock #
Description
JAB37121-0000 .....Switch High Pres 20 To 40 PSI
High Pressure Switch
Stock #
Description
7 5/16"
7 Lbs.
Pressure Switch
Stock #
Description
JAB18916-0025 .....Pressure Switch 31600 25 psi
JAB37121-0010 .....Switch High Pres 20 to 40 PSI
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
Jabsco Impellers
287
Pumps & Plumbing
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
Jabsco Impeller Chart
Pumps & Plumbing
288
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
Jabsco Impellers
289
Pumps & Plumbing
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
Jabsco Impellers
Pumps & Plumbing
290
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
Jabsco Impellers
291
Pumps & Plumbing
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
292
Pumps & Plumbing
Jabsco Impellers
Replacement Impellers:
Cross-reference Jabsco impellers that are
interchangeable & serve as a direct replacement
to other brands, producing the same required flow rate
with the quality and long life expected from genuine
Jabsco impellers.
Crusader
Jabsco
20300......................18948-0001
Mercruiser
Jabsco
47-59362 ................17954-0001
Johnson
Jabsco
1027 B ....................3085-0001
1028 B ....................17937-0001
806 B ......................4528-0001
1026 B ....................18673-0001
1029 B ....................17935-0001
801 B ......................4568-0001
802 B ......................6760-0001
814 B ......................17936-0001
Call Toll Free: (800) 426-2783 8-5 M-F
Sherwood
Jabsco
9959........................18838-0001
10615......................18948-0001
Oberdorfer
Jabsco
6617........................6303-0001
7441........................17937-0001
6603........................4598-0001
7054........................17935-0001
8922........................18948-0001
Perkins
Jabsco
0460024..................17937-0001
0460027..................17936-0001
0460038..................1210-0001
NA 90012 ..............18948-0001
24880031................17937-0001
24880178................18838-0001
24880190................3085-0001
24880194................18673-0001
24880272................4528-0001
Volvo
Jabsco
801277....................17937-0001
803729....................4528-0001
804696....................18673-0001
807904....................17935-0001
818680....................4598-0001
825940....................3085-0001
825941....................17937-0001
825942....................17935-0001
831182 ....................4568-0001
833550....................4528-0001
834794....................22120-0001
835182....................4568-0001
835512....................18838-0001
835874....................18948-0001
842857....................17936-0001
845796....................17936-0001
860203....................1210-0001
897055....................18673-0001
Yanmar
Jabsco
104211-42070 ........4528-0001
129470-42530 ........3085-0001
Seattle: (206) 285-5010 Fax: (206) 285-7925
Jabsco Impellers
293
Pumps & Plumbing
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
Jabsco Impellers
Pumps & Plumbing
294
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
295
Jabsco Impellers
Stock #
Description
JAB1210-0001 .......Impeller Neoprene
JAB1210-0003 .......Impeller Nitrile
JAB14750-0001 .....Impeller Neoprene
JAB14750-0003 .....Impeller Nitrile
JAB17018-0001 .....Impeller
JAB17255-0003 .....Impeller Nitrile
JAB17370-0001 .....Impeller For Gm Eng 17360 Pump
JAB17935-0001 .....Impeller Neopr 836 Multiblade
JAB17954-0001 .....Impeller Mercruiser 4759362
JAB17956-0001 .....Impeller Neop 6056 Multiblade
JAB18777-0001 .....Impeller For 50410
JAB18838-0001 .....Impeller Sherwood 9959
JAB18948-0001 .....Impeller Sherwood 10615
JAB18958-0001 .....Impeller Neopr Sherwood 17000
JAB31130-0061 .....Impeller Hino Diesel
JAB50070-0040 .....Puller Impeller 2-1/4 -2-9/16”
JAB50070-0200 .....Puller Impeller 3-1/16 - 5”
JAB6056-0003 .......Impeller Nitrile 6050, 6850
JAB6760-0001 .......Impeller Neoprene 2”
JAB6760-0003 .......Impeller Nitrile 2”
JAB836-0001 .........IMPELler Neoprene
JAB836-0003 .........IMPELler Nitrile
JAB920-0001 .........IMPELler Neoprene
JAB920-0003 .........IMPELler Nitrile
JAB9200-0023 .......Impeller Nitrile High Pressure
Call Toll Free: (800) 426-2783 8-5 M-F
Globe Resilient Blue Impellers
Only impeller able to run dry for 15 minutes.
• Made of elastomer compounds developed for optimum
performance & self lubricating for run dry protection.
• U.S. Coast Guard specified.
Stock #
Description
GLB025..................Impeller Globe For Jabsco 6303
GLB050SS .............Impeller Globe For Jabsco 5929
GLB100V...............Impeller Globe For Jabsco 22120
GLB110SS .............Impeller Globe For Jabsco 6056
GLB1113... .............Impeller Globe For Jabsco 17935
GLB1115. ...............Impeller Globe For Jabsco 4598
GLB1213................Impeller Globe For Jabsco 17936
Pumps & Plumbing
Jabsco Impellers
Available in Nitrile or Neoprene.
Impeller Pullers
An easy way of removing flexible impellers from a
pump's impeller bore.
Tighten tool's grip fingers into rubber hub of impeller
& turn extraction screw clockwise to pull impeller out.
Small puller:
For impellers with overall diameters from 2-1/4" to 2-9/16"
(silhouettes K,L,M,W,X & Y).
Large puller:
For impellers with overall diameters from 3-1/6" to 5"
(silhouettes O, Q, R, U, & Z).
Stock #
Description
JAB50070-0040 .....Small Puller
JAB50070-0200 .....Large Puller
Impeller Puller
Stainless pullers. -1 are display packed.
• Easy removal of impeller from pump.
Stock #
Imp. Size
SDG660020 ...........3-1/6 - 5"
SDG660020-1 ........3-1/6 - 5"
SDG660040 ...........2-1/4 - 2-9/16"
SDG660040-1 ........2-1/4 - 2-9/16"
Seattle: (206) 285-5010 Fax: (206) 285-7925
296
Flojet Pumps
Flojet 4325 Series Water System Pump
Designed for 6 or more fixtures, 4.5 GPM.
• For use with 1 to 5 gallon accumulator tank.
• Provides quiet operation and smooth flow.
• Install with new Flojet strainer (included) to
protect pump from debris.
Dimensions: 3.75"H x 6.3"W x 9.9"L
Ship Wt. 6.0 lb.
Pumps & Plumbing
FLOJET PUMPS
• Run dry without harm to the pump.
• Include plug-in ports for easy installation
Model #
Flojet 4405 Series Water System Pump with Bypass
Designed for up to 5 fixtures.
• Smooth water flow, pumps over 3.3 GPM.
• Delivers smooth, steady water flow from 1 to 3 GPM
without the need for an accumulator tank.
• Special internal bypass feature eliminates pulsating
water & pressure switch chatter.
• Install with new Flojet strainer (not included) to
protect pump from debris.
Ship Wt. 3.9 lb.
Model #
Volts
Open Flow
Shut Off
Stock #
Amps
Description
GPM
FLO4125-114 .........Bilge Pump........5GPM 12V DC
Model #
Stock #
Volts
Amps
GPM
FLO4125-414.........32V.........2.8...........5.0
FLO4125-502A .....12V.........8.0...........5.0
Call Toll Free: (800) 426-2783 8-5 M-F
Shut Off
Amps
Volts
Open Flow
Shut Off
Amps
FLO4305-500.........12V.........3.3 GPM .35 PSI .....3.9
FLO20409-043.......Service Kit
General Purpose Bait Tank Pump
Continuous duty motor & thermal overload protection.
No harm if runs dry. Self priming can install above water line.
• Calibrated for correct water movement for lively bait.
• Use with 15 to 30 gallon tanks. Includes 3/4" strainer.
Uses:
• Diesel fuel, liquid transfer jobs, dockside pumping.
• Dewatering or circulation, engine oil changing, oil elastometer.
• Plug-in ports, easy install: 2 for garden hose & 2 for 3/4" hose barb.
3.75"H x 6.3"W x 8.2"L..........3.9 Lbs.
Stock #
Flojet Quad II
General Purpose Livewell Pumps
Use for diesel fuel transfer, liquid transfer
jobs, dockside pumping,dewatering or
circulation, engine oil changing.
• Fitted with oil resistant elastomers.
• Self-priming, may be mounted above the
wateline. Heavy-duty ball bearings, thermal overload protection.
• Continuous duty motor. Provides quiet operation & smooth flow.
• Runs dry without harm to pump. Includes plug-in ports for easy installation, two garden hose ports and two 3/4" hose barb ports.
• Includes a 3/4" inlet strainer.
Open Flow
Flojet 4305 Series Water System Pump
• Smooth water flow, pumps over 3.3 GPM.
• Provides quiet operation.
• May be used with an accumulator tank.
• Designed for up to 5 fixtures.
• Install with new Flojet strainer (not included)
to protect pump from debris.
Ship Wt. 3.9 lb.
FLO4405-143 ........12V.........3.3 GPM 35 PSI .....3.9
FLO4405-343 ........24V.........3.3 GPM 35 PSI .....4.0
FLO4405-443 ........32V.........3.3 GPM 35 PSI .....1.3
FLO20409-043 ......Service Kit
Quad Bilge Pump
Continuous duty motor & thermal overload
protection.
• Self primes up to 10 Ft. above the bilge.
• Manual on/off switch or automatic level
control connect to pump.
• No harm if runs dry.
• Includes 3/4" barb inlet strainer.
• Fitting: Plug-in ports, easy installing, 2 for garden hose & 2 for 3/4"
hose barb.
3.75"H x 6.3"W x 9.9"L........6.0 Lbs.
Volts
FLO4325-143L ......12V.........4.5 GPM .40 PSI .....6.0
FLO20409-043.......Service Kit
Description
GPM
FLO4105-501A ......Pump General Purpose.......3.3GPM 12V
Pressure Switch for Pumps 4305 & 4325
Flojet switch.
Stock #
Description
FLO2090-118 .........Pressure Switch 4305/4325
Seattle: (206) 285-5010 Fax: (206) 285-7925
297
Jabsco Water System Pumps
Stock#
Sensor Max VSD Constant Pressure
Water System Pump
Pressure sensor controlled, with variable
speed drive - Serves 1 to 5 outlets.
Electronic speed control for steady flow &
constant pressure. Amp draw reduces as
flow reduces to conserve energy, ranging
from less than 1 Amp to max 15 Amps.
Overload protection. Strainer included
Must have battery installed.
1/2".ID Hose or 1/2" Quest threads. 4-1/4" Long x 2 -/8" Wide x 2" High.
Description
JAB32900-0092 .....Washdown Kit
Parmax 1.9 & 2.9 Water System Pump
For vessels requiring smooth low-flow.
Internally grounded 3 chamber diaphram ondemand for vessel
with: shower, water heater, & up to 3 faucets.
• Self prime to 6ft. Dry-running. Soft rubber mounts.
• Screw-less diaphram eliminates leak paths, low noise.
• Can eliminate need for accumulator tank.
1/2" Hose Barb or 1/3" NPT..........9" Long x 4 .5"W x 4.5"High
Stock #
Description
JAB31295-0092 .....Pump Parmax 1.9 GPM 25/45# 12V
JAB31395-0092 .....Pump Parmax 2.9 GPM 25/45# 12V
Par-Max 4 Washdown Pump Kit
Heavy duty motor. Powerful 4.3 GPM
flow rate.
• Shut-off pressure 50 PSI. 12 volt.
• Self priming up to 10 ft.
Connections for 3/4" ID hose. 9.8" Long x
4.2" Wide x 4.1" High
Stock #
Stock #
Description
JAB31750-0000........Pump Sensor Max 3.7 GPM 25/35#...12-24v
JAB31755-0000........Pump Sensor Max 4.5 GPM 30/40#...12-24v
Pumps & Plumbing
Jabsco Washdown Kit
Comes complete with filter, hose,
nozzle and fittings.Pumps over
4.0 GPM. Operates at 12 vdc,
hosecoil extends to 25 ft.
• Provides quiet operation.
• Shut off pressure 60 psi. Self priming up to 10 ft.
• Suitable for high pressure applications.
Paramax 4 Pump
Multi-outlet water pressure pump serves 4
outlets at any time. Snap-fit ports simplify
both installation & removal.
• 4 piston diaphram sealed for smooth &
quiet operation. Self-priming up to 10Ft.
• Thermal overload protection, auto stops motor
should it overheat due to overload, with auto-restart feature.
• Diaphram design allows extended dry running.
• 24Volt DC model - Fuse:7 Amp, high pressure.
Pressure switch: cut-in: 20 PSI - Cut-out: 40 PSI High pressure.
Fitting: Connections for 1/2" ID Hose or 1/2" Qest threads.
Size: 9.8" L x 4.2" W x 4.1" High.
Complies: USCG 183.410 ISO 8846 (Marine ignition protection).
Stock #
Description
JAB31620-0094 .....Pump Parmax 4 .....4.5 GPM 24V 40 PSI
Description
JAB31700-0092 .....Pump Parmax 4 Washdown
Par-Max 4 Bilge Pump
Continuous rated bilge pump with
waterproof coating for harsh environments.
• 258 US GPH flow rate, 4.3 GPM.
Diaphram design.
• Shut-off pressure 50 PSI. Overload protection. 12 volt.
• Self priming up to 10 ft., includes puppy guard strainer.
Connections for 1/4" ID hose. 7-1/4" Long x 4" Wide x 4-1/10" High
Stock #
Description
Weight
JAB31705-0092 .....Pump Parmax 4 Bilge ............5.5 Lbs.
Par-Max 3 Water System
New generation multi-outlet water pressure pump.
• Handles 3 or more 1/2" (13mm) outlets
at any one time.
• Snap-fit ports simplify both installation
& removal for routine service.
Fittings for 1/2" ID hose or 1/2" Quest threads.
8.6" long x 4.2" wide x 4.1" high
Stock #
Description
Stock #
Description
Weight
JAB31620-0092 .....Pump Parmax 4 4.3GPM 12v Wps......6 Lbs.
Port Kit
Accesories for pumps. 2 per pack.
Stock #
Weight
JAB31600-0092 .....Pump Parmax 3 3.5GPM 12v Wps...4.5 Lbs.
Call Toll Free: (800) 426-2783 8-5 M-F
Par-Max 4 Water System
New generation multi-outlet water pressure pump.
• Serves 4 or more 1/2" (13mm) outlets at any one time.
• Snap-fit ports simplify installation & removal for routine service.
Fittings for 1/2" ID hose or 1/2" Quest threads.
9.8" long x 4.2" wide x 4.1" high
Description
JAB30642-1000 .....Port Kit 90° 3/4” Hose Barb
JAB30649-1000 .....Port Kit 1/2" Threaded
JAB30650-1000 .....Port Kit Garden Hose
JAB30651-1000 .....Port Kit 90° 1/2” Hose Barb
Seattle: (206) 285-5010 Fax: (206) 285-7925
Pumps & Plumbing
298
Water System Pumps / Accumulator Tanks
Electric Galley Pump & Faucet
Economical running water at the turn of a switch. Quiet operation, electric
pump is compact, easy to install. Draws only 1.6 amps at 12 volts.
Pumps 1 GPM at 5 PSI (3.8 L/min at 35 kPa).
• Attractive faucet with stainless steel swing spout.
• Easy-to-clean white plastic base & built-in switch to operate pump.
• Switch rating up to 5 Amps at 12 Volts.
• Available as separate pieces or as pump/faucet combo package.
• Pump & faucet have a 3/8" hose connection.
• Centrifugal pump is not self-priming. Must be mounted below water
level or tank. Pump may be screwed directly into water tank.
Stock #
Desc.
GPM
Amp
Weight
JAB42510-0000 .....Pump Only .............2.4...........1.6 ..........3/4
JAB42530-0000 .....Pump & Faucet ......2.4...........1.6 ..........1
Par Accumulator Tank
A more compact pneumatic bladder tank to fit
smaller systems or spaces. Smooths faucet &
shower flow by eliminating pulsations & water
hammer & it also increases pump life.
• Pressurized tank, to 20 PSI, can be fine-tuned
to each system.
• Mounts easily in any position.
• New convenient snap-in barbed or threaded
hose fittings.
Diameter: 4-3/4" (119mm). Height 13 1/4" Weight: 1.6 lb. (.7 kg),
Working Volume: about 1 Aq. (850 ml);
Maximum working pressure: 125 Psi.
Stock #
Descirption
JAB30573-0000 .....................Par Accumulator Tank
Accumulator Tank
Pneumatic accumulator tank for smooth flow
from faucets & shower. Reduces pump cycling.
Eliminates pulsations & water hammer.
• Water separated from air chamber by diaphragm
& polypro tank liner.
• Tank volume: 2 gallons with working water
volume of about 1 gallon.
• Mounts horizontally or vertically, even upside
down.
• Port is 3/4" NPT (male). Includes brackets &
band clamps.
• Pre-pressurized to 20 psi. Tank may be fine tuned to cut-in pressure of
pump. Diameter: 8" (203mm). Height: 12 5/8" (320mm.
Weight: 5 Lb. (2.3 kg). Max working pressure 100 PSI: (690 kPa).
Stock #
Description
JAB18810-0000 .....................Accumulator Tank
Call Toll Free: (800) 426-2783 8-5 M-F
Par "Topsider" Galley Pump
Economical, attractive white galley pump/lavatory hand pump.
• Simple, easy countertop mounting.
• Smooth, convenient, angled stroke with instant self-priming performance. Topmount leaves maximum space under the counter. Easy to
service above the countertop.
• 1/2" hose connection. Weight. 1 Lb. (0.45kg).
Stock #
Description
JAB37220-1010 .....Topsider
Manual Galley Pump
Stock #
Description
IMTFYNWS-63B ..Galley Pump FynSpray Black
IMTFYNWS-63W .Galley Pump FynSpray White
Shower Drain Pump
Updated version of 37020 pump for bilge, shower & sink drain
pump. Corrosion resistant, quiet. Self priming to 6 ft.
3/4" Hose..........7 1/2" Deep x 5 1/4" Wide x 5 1/4" High.......5 1/2 Lbs.
Stock #
Description
JAB37202-2012 .....Pump Bilge Shower 12V 10a....4.3Gpm
Pressure Storage Tanks
Matched to pump, cut on pressure prevents waterlogging by
separating air charge from system water pressure. The result
is smooth pressure, even temp mix & reduced pump cycling.
• Mount in any position & in cold water plumbing after the pump.
• PST tanks used for fresh or saltwater. Mount hardware included.
Stock #
Description
Gallons
Dia Length Plumb
Drawdown
GRCPST1...Press Stor Tank.... 1 Gal.....8.0"....3/4"... 1.0gal
GRCPST2...Press Stor Tank...1.25Gal...11.0"....3/4"... 2.5gal
GRCPST3...Press Stor Tank....2.7 Gal.. 15.4".....1"..... 5.5gal
GRCPST4...Press Stor Tank....4.5 Gal.. 15.4".....1"..... 7.0gal
GRCPST5...Press Stor Tank... 6.4 Gal.. 15.4".....1"..... 10gal
MaxPSI
100
100
100
100
100
Seattle: (206) 285-5010 Fax: (206) 285-7925
299
Bilge Pump Accessories
Stock #
Description
Description
Stock #
JAB46400-0000 .....Strainer
GRCWSB1000
Ports
3/4” Barb
1/2” Hose
3/8” Hose
1/2” NPT
3/4” X 90
1/2” Hose 90
1/2” NPT 90
3/8” NPT
90 QuadxQuad
Jabsco High Capacity Strainer
Large surface area of 1/4" mesh intake strainer keeps debris from
clogging bilge pump. Keeps pump running cleaner & longer. 1" hose
connection. Adjustable mounting bracket for either flat or vee bottom
mounting surface.
13-1/2" (343mm) long, brass & polypropylene construction.
Stock #
JAB35890-0010
Description
Pumpgard In-Line Strainer
Pumpgard in-line strainers keep debris & particles from
clogging your bilge pump, helping pump run clearer,
longer, cutting down on repairs.
Pumpgard uses clear plastic housing for quick inspection, for quick disassembly & easy cleaning of 16 mesh
stainless steel screen.
Stock #
Description
JAB36200-0000 .....................Strainer 3/4" Hose
JAB36200-1000 .....................Strainer 5/8" Hose
SeaDog In-Line Strainer
• 1 M Polypropylene Body - Polycarbonate clear lens
• Stainless Steel filter Screen: 50 mesh
• Mount above water on suction side of pump.
Stock #
Description
SDG364135 ........... In Line Strainer 1/2" Hose
SDG364137 ........... In Line Strainer 3/4" Hose
"Pumpgard" In-Line Strainer
PAR Pumpgard prevents dirt & other particles from entering
pump intake allowing pump to run cleaner and longer.
• Pumpgard cuts down on repairs and is easy to install.
• Works in any position. Transparent housing for quick inspection.
• 50 mesh stainless steel filtering screen.
• Slip-on ports 1/2" ID hose, threaded, or flare ports available.
Stock #
Ports
JAB36400-0000 .....................1/2" Hose
JAB36400-1000 .....................1/2" Threaded
JAB36400-9000 .....................Snap In
Strainer
Jabsco Low Profile Strainer
Low profile strainer keeps debris out of bilge pump & gets
water level down to less than 1/4".
• Only 1" high & 2-3/8" diameter.
• 1/8" x 1/2" strainer channels, to fit almost any bilge area.
• Sturdy 1 piece naval bronze casting.
• 1/2" (16mm) slip-on hose.
Stock #
Description
JAB36220-0000 .....Pumpgard 3/4”
"Pumpgard" Strainer
These compact pre filters prevent particles from jamming valves and
causing breakdowns. Fine mesh screens.
• Screw on caps for quick cleaning.
• Works in any position. Transparent housing for quick inspection.
Stock #
Description
Pump Guard
In-line strainer keeps debris & particles from clogging
pump. Clear plastic housing for quick inspection.
NPT:
1/2” NPT
3/4” NPT
1” NPT
1-1/4” NPT
Includes two 3/4" (19mm) garden hose •
Port adaptors mounted on 1/2" barbed port.
JAB17250-0003 .....................Self-Priming Drill Pump
Inlet Strainers Pump
Protect fresh water pumps from debris.
• White nylon strainer head & clear plastic sight glass.
• Mount bracket included.
• Use WSB for fresh water systems ( #304 SS basket).
GRCWSB500.........Strainer Nylon
GRCWSB750.........Strainer Nylon
GRCWSB1000.......Strainer Nylon
GRCWSB1250.......Strainer Nylon
Use for draining engine oil through
dipstick tube, pumping, scavenging jobs
many uses around boat or home.
Stock #
JAB17215-0000 .....................Drill Pump Kit
Stock #
Self-Priming Drill Pump
Self-priming drill pump chucks into a
standard 1/4" drill motor and pumps up
to 3 1/2 GPM (13 L/min).
Pumps & Plumbing
Jabsco Drill Pump Kit
Self-priming. Kit has same utility pump as
17250-0003. Includes all accessories required to change engine oil
through dipstick tube.
• 3 Ft. of 1/2" hose, probe adaptor, 1/4" x 40"
dipstick probe.
• Packed in poly bag with display header
card.
• Weight 1 lb. each - Standard carton 12 kits.
Description
JAB14555-0000 .....................Bronze Strainer
Call Toll Free: (800) 426-2783 8-5 M-F
Inlet strainers
Keeps debris & particles from entering your Flojet pump.
• Plug-in Quad port 90° strainer allows for easy install & fit.
• Threaded bowl makes cleaning easy.
• Stainless steel: 40 mesh screen for fresh water.
Stock #
Description
Inlet
FLO1740-000.........Strainer....3/4” Hose Barb
FLO1740-002A ......Strainer....1/2” Hose Barb
FLO1740-010.........Strainer....Quad Port 90° x 3/4” Hose
Seattle: (206) 285-5010 Fax: (206) 285-7925
300
Hand Pumps
Pumps & Plumbing
Thirsty-Mate Hand Pumps - Beckson
All plastic. Self lubricating, self-priming and very easy to clean.
Will not rust or corrode. Won't mar boat.
• If clogged, remove foot valve assembly & clean out the inside.
• Spare parts: like replacement foot valve assemblies & hoses are available.
• Thirsty-Mate hand pumps: made in USA of finest materials available.
118 Series
Length:
Diameter:
Strokes/Gal:
Pumps:
Diameter:
Strokes/Gal:
Pumps:
18" ..........................1-1/4" ......................10 ...........6 Gal per Min.
124 Series:
Length:
BEC118PP
Stock #
24" ......................... 1-3/4" .....................6..............10 Gal per Min
136 Series:
Length:
Diameter:
Strokes/Gal:
BEC124PF
BEC136PF
BEC136PF6
Description
BEC118PF .............................18" with 24" Hose
BEC124PF .............................24" with 24" Hose
BEC124PF6 ...........................24" with 6 ft. Hose
BEC136PF .............................36" with 36" Hose
BEC136PF6 ...........................36" with 6 ft. Hose
Pumps:
36............................1-3/4" ......................4..............13 Gal per Min.
"Handy Boy" Handy Pump
Self-priming hand pump kit:
Adaptors, tubes & hoses for dozens of pumping needs. Engine crankcase pumpout through
dipstick tube, diesel fuel transfer, or bilge
pump. "Handy Boy" can be used as air pump
to inflate air matresses, blow out fuel lines.
Includes: two 1/2" x 3' (12mm x 1m) hoses.
• 2 dipstick probes 1/4", neoprene intake adaptor/tube connector.
• Weight 2 lbs. each.
Stock #
Description
JAB33799-0000 ....................."Handy Boy" Handy Pump
Jabsco "Little Pal" Hand Pump
Compact multi-purpose hand pump does many
draining & liquid transfer jobs.
• Small enough to fit in tool or tackle box.
Includes: 2" (0.6mm) hose & draw tube for
draining crankcases through dipstick tube.
• Weight 1 lb. each. Standard carton 12.
Stock #
Handy Mate Transfer Pump Kit
Especially versatile, comes with kit of tubes &
hoses,
reducing foot & adaptor. Use for bilges, sump tanks,
transfer, or oil changing from engine crank case,
stern drive or inboard.
• Tube to insert in dipstick hole for oil pump out.
• Tough marine plastic will not rust or corrode.
• Non-sparking for safety. No priming to start pump
action.
• Red discharge tube, gray hand pump.
Stock #
Description
BEC212PC .............Kit Handy Mate 12” Pump
Beckson Siphon Mate Transfer Pump
Combination displacement lift & siphon pump with
valves suitable for transferring fuel. Clear tubing.
Not intended for solvents that attack PVC or liquids
of over 120°. Be sure to rinse.
• Use for diesel, oil, or water.
Stock #
Description
BEC109PC .............Siphon-Mate Pump
Description
JAB34060-0010 ....................."Little Pal" Hand Pump
Scotty Hand Bilge Pump
• Solid brass piston rod for strength & durability.
• Easily disassembled for cleaning.
• 1-1/2" barrel means quick pumpouts.
• 5 year warranty.
• Includes 24" of 1-1/8" black bilge flex hose.
Stock #
Description
SCT545 ....Bilge Pump Hand 21” with 24” Hose
Call Toll Free: (800) 426-2783 8-5 M-F
Scotty Hand Kayak Pump
• Solid brass piston rod for strength & durability.
• Easily disassembled for cleaning.
• 1-1/2" barrel means quick pumpouts.
• 5 year warranty,
• Includes 24" of 1-1/8" black bilge flex hose.
Stock #
Description
SCT545KB.............Bilge Pump Kayak 21” with Float
Seattle: (206) 285-5010 Fax: (206) 285-7925
301
Hand Pumps
Use Bosworth Guzzlers to:
• Dewater bilges, holds & sumps aboard boats of all kinds.
• Dewater trenches, meter boxes, pits, etc.
• Hand Bilge Pump with many other uses.
400 Series (1" pump)
Stock #
BOS400H ...............Horizontal mount pump
BOS400V ...............Vertical mount pump
Parts:
BOS400-13 ............1" Diaphragm
BOS40014 ..............Flapper valve
500 Series (1-1/2" pump)
Stock #
BOS500H ...............Horizontal mount pump
BOS500V ...............Vertical mount pump
Parts:
BOS500-13 ............1-1/2" Diaphragm
BOS50014 ..............Flapper valve
Bosworth Guzzler 400 & 500 models are self priming.
• Capable of a 12 Ft. suction lift & a 12 Ft. delivery head.
• 10 & 15 GPM Guzzlers: built of injection molded DuPont Delrin.
• Both models have reinforced diaphragm & flapper valves
& are available w/ thru deck mounting capability.
BOS500H
BOS400H
2" Guzzler 2600 Pump - Bosworth
Pumps over a liter per stroke for unmatched value
& performance.
Portable, mounted either horizontally/vertically
for on the spot dependability.
Hand operated, no sparks, no electricity needed.
BOS500V
Pumps & Plumbing
Bosworth Guzzler 400 & 500 Pumps
World renowned Guzzler pumps liquids fast.
• Versatile. Easy hand operation - No electric power required.
• Fast, large valve openings speed up most pumping chores.
• Portable lightweight design. Lasting construction & durable.
• Made of the highest quality materials. Warranty.
• 400 Guzzler uses 1" I.D. Hose.
• 500 Guzzler uses 1 -/2" I.D. Hose.
Bosworth Pump Accessories
Foot Strainers for Hose
Stock #
BOS084 ..................1"
BOS849 ..1-1/8"
BOS085 ..................1-1/2"
Hose Cuff
Stock #
BOS055 ..1-1/2" End Cuff
Advantage of the Guzzler 2600:
Pumps liquids fast...
• 10 position clamp ring for many different positions.
• Strong anodized aluminum handle, quickly
converts horizontal/vertical position.
• Stainless steel button, actuator & clevis for long
life & smooth, sure action.
• Reinforced diaphragm & flapper valves for
dependable pumping.
• Pumps up to 30 gallons per minute.
• Corrosion resistant, impervious to most fuel oils,
solvents & detergents.
Stock #
BOS2600 ................Bosworth 2600 Pump
Thru Deck Mounting Kit
Convenient kit, for: 400, 500 or 2600 pump to
install below the deck.
Consists of deck plate & cover, boot, & stand-offs.
Stock #
BOS034 ..................Thru Deck Mount Kit
Fire Nozzle
Converts a Guzzler pump to a portable fire fighting pump;
Produces up to a 30 ft. stream of water at 8 gallons per
minute.
• Meets/exceeds U.S. Coast Guard reqs. for
portable fire pumps on Class S & Class L vessels
or use as a handy nozzle with wash down pumps.
Stock #
BOS024 ..................Fire Nozzle
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
Pumps & Plumbing
302
Hand Pumps
Amazon Universal
• Push-fit port - 1 elbow included.
Optional swivel 360° for installation choices.
• Safety feature for operation from inside & outside
cabin (with optional thru-deck kit).
• Quick release clamp ring gives fast access
for blockage clearance.
• Flow rate of up to 22 GPM.
• Great solids handling ability, use with holding
tanks.
• Connections for 1-1/2" ID hose.
Stock #
Amazon Warrior
• Robust, alloy body very suited to workboat &
safety applications. Detachable handle.
• Double diaphragm design gives maximum
efficiency, & added safety because each side
of pump operates independently.
• Solid 18" handle allows sustained high outputs
of up to 30 GPM.
• Connections for 1-1/2" ID hose
Description
JAB29270-0000 .....Universal pump, w/ detachable
handle & 1 piece push-fit elbow.
Amazon Bulkhead Pump
• Repositionable ports & body offers 96
assembly variations. Detachable handle.
• Sustainable outputs up to 10 GPM.
• Connections for 1" ID hose.
Stock #
Stock #
Description
JAB29280-0000 .....................Warrior pump
Description
JAB29240-0000 .....Bulkhead pump
End Suction Brass Bilge Pump
Place pump end in low point of bilge & powerful self-priming action gives full suction on first stroke.
• Quick, easy pumpout of bilges & other flooded areas.
• Compact, easy to stow, only 17" (430mm) long.
Includes 5 ft. length of 1/2" discharge hose.
Weight: 1.5 Lb.
Stock #
per gal.
Stroke
Overall
Cyl. dia.
JAB33760-0000 .....15" ..........13" ..........17" ..........1-1/4"
"Full Stroke" Brass Bilge Pumps
High quality hand bilge pumps: brass cylinders & oil resistant plungers, intake & discharge caps.
Includes adjustable mounting brackets for sufficient clearance to easily pump.
Meets standards of portable hand bilge: CFR Tile 46, Chapter 1, Subchapter T, Subpart 182.25-10.
Stock #
Strokes
per gal
Stroke
Overall
Cyl. dia.
Hose
Connection
JAB33745-0000 .....7..............13 3/4" ....22 1/2".....1 3/4" ......1"
Wt.
(lb.)
4
Hose - Hosemaster
Water storage hose system - Compact size fits most anywhere.
• Use to wash down or ship to shore connection.
• Exclusive levelwind feature for safestorage onto reel.
• Takes advantage of standard garden hose fittings.
• Can be mounted in a variety of positions.
Stock #
Description
GMP0555008U ......Hosemaster 8 Ft. 1/2” Hose NPT
GMP0555116U ......Hosemaster 16 Ft.1/2” Hose NPT
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
303
Water System Pump
Stock #
Description:
Volt:
FLO4325-143A ......Water System Pump....12V
FLO4325-043A ......Water System Pump ...115V.
Stock #
Description
FLO4305-144A ......Washdown Pump with Strainer.
FLO4305-144L ......Washdown Pump with Strainer & Nozzle
Water Jet Washdown Pump Kit
Powerful pump for sports/commercial
fishing & work boats,
with automatic shut-off. High performance pump.
• Pressure nozzle (non-corrosive).
Includes 3/4" barb inline strainer.
• Fresh or salt water use. No harm if
runs dry. Self primes.
• May also be used for full flow bait
tank circulation.
• Automatic shut-off feature when hose
nozzle is in off position.
• Plug-in Ports, easy install: 2 for garden hose & 2 for 3/4" hose barb.
3.75"H x 6.3"W x 9.9"L.......4.5..24V...20/40psi.........6.0 Lbs
Stock #
Pumps & Plumbing
Premium Washdown Pump
Use for cleaning pleasure boats, fish
boxes, scaling stations, anchor chains
and dinghies. Automatic high performance pump.
• Pressure nozzle (non-corrosive). Includes 3/4" barb inline strainer.
• Fresh or salt water use. No harm if runs
dry - Self primes.
• May also be used for full flow bait
tank circulation.
• Automatic shut-off feature when hose nozzle is in off position.
• Plug-in ports, 2 for garden hose & 2 for 3/4"hose barb.
3.75"H x 6.3"W x 8.6"L........3.5..12V....20/40psi.........3.9 Lbs
Water System Pump
• For use with 1 to 5 gallon accumulator
tank.
• Designed for 6 or more fixtures.• Quiet
smooth flow.
• No harm if runs dry.• Strainer included.
• Plug-in ports, easy install: 2 for garden
hose & 2 for 3/4" hose barb.
3.75"H x 6.3"W x 9.9"L........4.5....40psi.......6.0 Lbs
Water System Diaphram Pump
• Fully automatic with long life pressure switch.
• Use with: 1, 2, or 3 fixture system.
• Supplies: 1.3 to 2.3 GPM. Install with Flojet strainer.
Stock #
Description
GPM
FLO2100-12A......Pump 12v Water Sys.. 2.3GPM 30psi
Description
FLO4325-343L.. Washdown Pump Kit....with Nozzle & Strainer.
Washdown Spray Nozzle
Combined with PAR-MAX washdown pump.
• Disconnect nozzle has a multi-setting flow control for
fine mist spray to power-cleaning blast output.
• Works well with both fresh & salt water.
• Quick-disconnect nozzle can be removed from hose & used at another
outlet, without turning off pump. Performs well with other pumps.
High Volume Water Pressure System Pump
Integrated pump & accumulator tank system.
Compact design installs easily, mounts verically or horizontally.
Can run dry with no harm.
• Supplies 4.5 to 6 gpm with fully charged tank.
• FDA materials in pump & accumulator tank for drinking water.
• Self priming up to 10 ft. Includes assorted ports.
• Accumulator tank has total volume of 1.1 gallon.
7.2"H x 11.3"W x 12.8"Deep..........8.8 Lbs.
Stock #
Description
GPM
Stock #
Description
JAB30703-1000 .....Washdown spray nozzle
Plastic Hose Nozzle
Red plastic hose nozzle great for wash down or fire.
Stock #
Description
ARSPN15...............Nozzle Plastic 1 1/2”NPT x 10”
FLO2840-100A ......Pump High Vol Water Sys 12V 4.5 40psi
FLO2840-400A ......Pump High Vol Water Sys 32V 4.5 40psi
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
304
Vane Pump
Pumps & Plumbing
Junior Gear Puppy & Gear Puppy
Robust pump makes oil & diesel transfer easy for fixed
installation systems. Rugged bronze construction.
• Self priming up to 3 ft. Inlet filter supplied.
• Suitable for oils up to 150Cs, 15 minute duty rating.
Junior Gear Puppy can produce 3.5gpm.
Fuse: 3" x 6.5" x 5.5"
Stock #
Description
Fuse
Weight
JAB23220-2012....Junior Gear Puppy12v....10 A .. 4.8 Lbs.
Gear Puppy can produce 6.5 gpm.
3" x 6.5" x 5.5"
Stock #
Description
Fuse
Weight
JAB23230-2012 ..... Gear Puppy12v......15 A ........4.8 Lbs.
Utility Puppy 2000
Continuous rated, offers high flow for:
Bilge, deck wash, & general purpose use, 10 minutes dry running.
Bilge debris no problem for bronze body with flexible impeller.
• After use will dry run for 20 minutes.
• 500 US GPH output at 10 Ft. total head.
• Self priming up to 4 Ft. vertical lift.
Connections for 1/4" male thread....7-1/2" L x 4-3/4" W x 3-1/2" H
Stock #
Description
Weight
JAB23920-9403 .....Pump 12v Utility Puppy .......9.7 Lbs.
Call Toll Free: (800) 426-2783 8-5 M-F
Positive Displacement Rotary Vane Pump
Bronze body. Delrin rotor & blades.
• Self-priming. Reverse & non-reversing.
• "Ignition protected" motor has #316 SS shaft.
• Touchpad control is optional. (Order SPO-XX-RT)
Non-Reverse:
Stock #
Description
GRCSPO60N12V ....Vane Pump HD 12V
Reversing:
Stock #
Description
GRCSPO60R12V .....Vane Pump HD 12V Reversing
Seattle: (206) 285-5010 Fax: (206) 285-7925
305
Johnson Pumps
Self-Priming Flexible Impeller Pump
Excellent multi-use pump for cooling engines, bilge, deckwash,
freshwater, fuel transfer & other applications.
• Stainless steel endcover, wearplate & shaft. 1" NPT ports.
• Bronze body with mechanical O-ring seal.
• Permanently lubricated ball bearings. Neoprene impeller.
• Drive shaft 5/8." Double ball bearing. Bearing spacer.
1" NPT. 6.69"L x 4.72"W x 1.97"H. 4 Lbs.
Stock #
Stock #
Description
JNP10240747E.......Pedestal Pump 3/8" NPT F4B800 F4B8007
Original Johnson Pump Style
Bronze body, stainless steel shaft, 1-1/4" ports, 1"shaft keyd.
• Mounted shaft with perm. Lubricated double ball bearings.
• Mechanical seal, neoprene impeller.
Stock#
Description
JNP101302195 .......Pump 62 GPM F8B8
Pedestal Pump
Excellent multi-use pump for cooling engines, bilge, deckwash,
freshwater, fuel transfer, & other uses.
• Stainless steel endcover, wearplate & shaft.
• Bronze Body. Mechanical seal. O-ring sealed
• Permanently lubricated ball bearings.
• Drive shaft 3/8." Double ball bearing.
1"NPT. 4.37"L x 3.15"W x 1.97"H. 1.8 Lbs.
Stock #
Description
JNP102457151........Pump F5B-8007 Mech Seal
Pumps & Plumbing
Pedestal Pump
Excellent multi-use pump for cooling engines, bilge,
deckwash, freshwater, fuel transfer, & other applications.
• Bronze body. Mechanical seal O-ring sealed.
• Drive shaft 3/8". Double ball bearing. Bearing spacer.
1"NPT. 4.37"L x 3.15"W x 1.97"H, 1.8 Lbs.
Heavy Duty Electromagnetic Clutch Pump
Bronze body. Connection for vacuum switch.
• Mechanical seal and neoprene impeller.
• Permanently lubricated ball bearings. 1-1/2" ports.
• Clutch is electromagnetic 12V DC.
1 1/2" NPT. 8.85" L x 6.29" W x 4.88" H. 22 Lbs.
Stock #
Description
JNP1013022951......Pump with Clutch F8B5
Self-Priming Pump
Excellent multi-use pump for cooling engines,
bilge, deckwash, freshwater, fuel transfer, and
other applications.
• Bronze body, mechanical seal, O-ring
sealed.
• Drive shaft 3/8" - Double ball bearing - Bearing spacer.
3/8" NPT. 4.29" L x 3.14" W x 11.18" H. Weight 1.2 Lbs.
Stock #
Description
JNP10350384 .........Pedestal Pump 3/8”NPT F35b8007
Description
JNP10240747 .........Pedestal Pump 3/8” NPT F4b8007
Electro-Magnetic Clutch
Stock #
Pulley Drive Pump F35B8007
Same as Westerbeke # 32617. Pedestal mount. Pulley extra.
Stock #
Description
Description
JNP05321 ...............Clutch 12 Volt DC 2 x A-Belt
JNP05323 ...............Clutch 12 Volt DC 1 x B-Belt
JNP05325 ...............Clutch 32 Volt DC 2 x A-Belt
JNP05326 ...............Clutch 32 Volt DC 1 x B-Belt
JNP10350385E ......Pedestal Pump 3/8” NPT
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
306
Johnson Pumps
Pumps & Plumbing
Replacement Impellers. Johnson
Stock #
Description
JNP091026B ..........Impeller F4B Neoprene
JNP091026B9 ........Impeller F4B Nitrile
JNP091027B ..........Impeller Kit Volvo Gas Engines
JNP091028B ..........Impeller F7B Neoprene
JNP091052S9.........Impeller F3B Nitrile
JNP091077B9 ........Impeller F2P10 Nitrile
Aqua Jet Water Pressure System
Dramatically lower noise & water pulsation free flow due to
a 5 chamber design. Built-in thermal protection.
Recommend to install WPS-pumps with an accumulation tank.
Always use a PUMProtector inlet strainer before the intake.
3.4 GPM, 12/24V DC, motor100W.
• Nylon and polypropylene body. Santoprene diaphram.
• Pipe Valves: santoprene EDPM. Cut off pressure 41 PSI.
3/8" NPT/Hose1/2".......1/2" NPT/Hose3/4.........1/2"-14 NPSM
Stock #
Bilge, Deckwash, and Refueling
Pump
Use for bilge pumping, deckwash,
water circulation,
oil & diesel refueling etc. Do not use
for pumping parafin or other thin
petroleum products.
• Connection for vaccum switch.
• Bronze body. Stainless steel
shaft.
• Lip sea motor 12/24V DC
Fitting:
Dimension:
Weight
3/8 " NPT........6.7" L x 4" W x 3.22" H......4.5 Lbs.
Stock #
Description
JNP102451603 .......Pump 4 GPM 3/8” NPT F3b19
Multi-Purpose Pump
Fully equipped self priming multi-purpose pump,
ideal for water, oils & chemicals. Do not use for pumping
parafin or other thin petroleum products.
• Lip seal. Motor 12/24V DC ignition protected.
1/2" OR3/4"........6.77" L x 4.61" W x 3.07" H......3.5 Lbs.
Stock #
Description
JNP10241801 .........Pump 3.8 GPM 1/2” F2p10-19
Descriptioin
JNP1013250103 .....Water Pressure System
Heavy Duty Magnetic Driven Centrifugal Pump
• Enclosed motor, permanent magnet, ball bearing
mounted motor, designed for continuous use.
• PPA thermoplastic body.
5/8" or 3/4" Hose. .6.97" L x 2.68" W x 3.35" H......1.2 Lbs.
Stock #
Description
JNP102448603 .......Pump Cm10 5/8” Port 12/24V DC
Pump for John Deere
John Deere # RE47016 with vertical mounting holes.
Stock #
Description
JNP102439801 .......Engine Pump, John Deere with
Flange
Call Toll Free: (800) 426-2783 8-5 M-F
Johnson Pump for Volvo
For Volvo, AQ131, AQ140A -170. Volvo # 855517.
Stock #
Description
JNP10326212 .........Engine Pump Volvo F5b9
Seattle: (206) 285-5010 Fax: (206) 285-7925
307
Johnson Pumps
Heavy Duty Bilge Pump
Meets tough commercial duty & recreational
use.
• Liquid cooled 12 pole motor with double ball
bearings.
• Lip seal & is designed to maximize head &
flow.
Fitting:
Fitting:
Dimension:
3/4" Hose
3 x 4" Dia x 4.4" H
Stock
Description
Weight
14.4 oz.
JNP5703 .................Bilge Pump Auto 750GPH 12V
Weight
Stock #
Description
JNP16004.....Bilge Pump 1600GPH 1-1/8” 12V
Heavy Duty Bilge Pump
Meets tough commercial & recreational
duty use.
Liquid cooled 12 pole motor with double
ball bearings.
• Sealed off design eliminates shaft wear & allows for replacement.
• Impeller is designed to maximize head & flow.
Fitting:
Dimension:
Stock #
Description
1-1/8"or 1-1/2"NPT 4.25" Dia x 7" H.
Pumps & Plumbing
Auto Bilge Pump 750 with Float Switch.
Cartridge duo has automatic operation & equipped with
non-clogging, electronic float switch 750.
• Easy to install Dura-Port discharge ports to eliminate
stress cracking caused by over-tightened hose clamps.
• Delivered with both straight & 90° smooth elbow dura-port.
Dimension:
1-1/8" NPT...... 4.25" Dia x 5.86 " H............2.75 Lbs.
Weight
6 Lbs.
JNP22004 ...............Bilge Pump 2200GPH 1 1/8” 12V
Auto Bilge Pump with Float Switch
Cartridge duo has automatic operation and is equipped
with a non-clogging electronic float switch.
Easy to install dura-port discharge ports to eliminate
stress cracking caused by over-tightened hose clamps.
Delivered with both straight & 90° smooth elbow dura-port.
Fitting:
Dimension:
Stock #
Description
Weight
3/4" Hose........3" x 4" Dia x 4.4" H
14.4 Oz.
JNP5903 .................Bilge Pump Auto 950GPH 12V
Cartridge Bilge Pump
Has some of the most advanced features in
the industry.
• Easy-to-install Dura-Port discharge ports to eliminate
stress cracking by over tightened hose clamps.
Fitting:
Dimension:
Weight
3/8"NPT......2.75"Dia x 4.4"H......9.6 oz.
Stock #
Description
JNP32503 ...............Bilge Pump 550GPH 3/4” 12V
Multiple Port Shower Sump
Includes a fresh water system onboard for showers,
dishwashing machines, galley sinks etc.
• Automatic shower sump turns on/off & has multiple inlet
ports for waste water from more than 1 tapping point.
• Check valve on outlet keeps water from returning to tank.
• Tight fitting lid minimizes splashing & odors.
• Filter mesh removes with ease.
Fitting:
Dimension:
Weight
3/8" NPT.......11.42" L x 8.26" W x 5.7" H......2 Lbs.
Stock #
Description
Cartridge Bilge Pump
Has some of the most advanced features in the
industry. Removable motor cartridge for cleaning
and replacement.
• Easy-to-install dura-port discharge ports to eliminate
stress cracking by over tightened hose clamps.
Fitting:
Dimension:
Weight
3/8" NPT.......2.75" Dia x 4.4" H......9.6 oz.
Stock #
Description
JNP32703......Bilge Pump 750GPH 3/4” 12V
JNP57151........Shower Sump 12V DC 1000 GPH
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
308
Johnson Pumps
Pumps & Plumbing
Ultima Bilge Pump 600 GPH
• Simple 3 wire design for easy installation.
• Dura-Port fittings 90° & straight 3/4"
discharge included.
• Optional check valve an industry exclusive.
• Patented "field effect" digital sensing is worry
free.
• No moving parts for activation. Mercury free
design.
3/4" Hose.. .5.50"L x 3.25" W x 4.125" H. 12V DC
Stock #
Description
JNP32472582 .........Ultima Bilge Pump 600 GPH
Ultima Bilge Pump - 1000 GPH
Simple 3 wire design for easy installation.
• Dura-Port fittings 90° & straight 3/4"
discharge included.
• Optional check valve an industry exclusive.
• "Field effect" digital sensing is worry free.
• No moving parts for activation. Mercury free
design.
3/4"Hose. 5.50"L x 3.25"W x 4.125"H. 12V DC
Stock #
Description
JNP32472602.......Ultima Bilge Pump 100 GPH
Sump Pump
115 volt pump. 13 GPM at a 10 ft. head. 1/6 HP
motor. Has 1" IPT, comes with 1" IPT to 1" hose
adapter. 10 foot cord.
Stock #
Description
JNP101021601 .......Sump Pump
Ultima Bilge Switch
Digital technology uses mirus field effect detector cells
producing micro-electrical fields to detect disruptions
caused by water & fluids.
• Cells are totally sealed & never contact water.
• Will not corrode and are not affected by oil or foreign debris.
• No moving parts, totally sealed solid state electronics.
• Environmentally sensitive, no mercury or exposed sensors.
• Activates at 2" fluid level & deactivates at 3/4" fluid level.
• A 3 second delay prevents false starts.
Stock #
Description
JNP36303.......Ultima Switch 20Amp Max 12/24V
Call Toll Free: (800) 426-2783 8-5 M-F
Heavy Duty Submersible Bilge Pump
High capacity, premiere pump in submersible
range.
Out performs all other comparable pumps on
market.
• Universal base plate & choice of 1-1/2" or
2" ports
for simple installation.
• Delivered with optional check valve.
Fitting:
Dimension:
Weight
1-1/2" & 2'" Hose........4.8 Dia. x 8.5" H.................5.4 Lbs.
Stock #
Description
JNP40004 ...............Bilge Pump 4000GPH 12V
JNP40004-24 .........Bilge Pump 4000GPH 24V
Ultima Combo 500 GPH
Bilge pump & ultima switch
- Rugged ABS fuel resistant
housing
Automatic water sensing switch
- Universal base, 316 stainless
steel.
Easy-to-install dura port discharge ports to eliminate stress
cracking.
Capacity:1.0m head (13.6V)
Capacity: Straight (13.6V)
38L/ min - 601 GPH
49L/ min - 778 GPH
Removeble check valve - Straight & 90° smooth elbow discharge ports.
Hose size: 3/4" - Discharge outlet: 3/4" Wire size: 30"16ga. tinned.
Fuse size: 5A - Draw: 2.5Amp 12V DC
Dimensions: 4 1/2" H x 2 3/4" W x "L
Stock #
Description
JNP07503 ...............Bilge Pump Auto 500 GPH 12V
Johnson Bilge Pump Control
Push button for manual or automatic pumping.
Automatic feature: operates in combination with
automatic bilge switches or electronic float switch
from Johnson Pump.
• 3 position switch panel in matt black finish.
• Integrated fuse holder & operating light, fuses
included.
Size
2.99" x 2.17" x 1.57"
Stock #
Description
JNP82004......Panel Switch 12V 3-Way with Fuse
Pressure Switch
Replacement pressure switch for AquaJet water
pressure systems - 40 PSI.
Stock #
Description
JNP094678101 .......Pressure Switch 40 PSI
Seattle: (206) 285-5010 Fax: (206) 285-7925
309
Rule Pumps
Rule Gold Series Bilge Pump
Silent operation with no vibration.
Features: double insulated long stack motor
for superior quality & performance.
• 5 year limited warranty. Anti-airlock protection.
• Easy clean snap-lock strainers.
• Exclusive moisture tight seals.
Stock #
Description
Rule Gold Series Bilge Pump
Silent operation with no vibration.
Features: a double insulated long stack motor
for superior quality & performance.
• 5 year limited warranty. Anti-airlock protection.
• Easy clean snap-lock strainers.
• Exclusive moisture tight seals.
Stock #
Description
Fitting:
Size:
1 1/8"Discharge outlet............2000 GPH
Stock #
Description
RULRM2000 .........Pump Rule-Mate 12V DC
Rule-Mate Bilge Pump, 1500 GPH
Automatic, high pumping capacity & reliability at
a lower cost. More exclusive design features than
any other pump.
Fitting:
Pumps & Plumbing
RUL04....Gold Series Pump 12V 1500GPH
Rule-Mate Bilge Pump, 2000 GPH
Automatic engineered to commercial standards.
The best selling automatic submersible bilge pump!
Size:
1 1/8" Discharge outlet...........1500 GPH
Stock #
Description
RULRM1500 .........Pump Rule-Mate 12V DC
RUL13A....Gold Series Pump 12V 3700GPH
Rule Automatic Bilge Pump, 2000 GPH
Engineered to commercial standards.
• Best selling high capacity submersible bilge
pump in the world.
• 1 1/8" discharge outlet.
Stock #
Description
RUL53S....... Automatic 2000 GPH 12V DC 3WR
Rule Automatic Bilge Pump, 3700 GPH
Heavy-duty construction for both commercial
& pleasure boat use.
• Known for trouble free operation & reliability.
• 1-1/3" discharge outlet.
Stock #
Description
RUL55S-3...... Automatic 3700 GPH 12V DC 3WR
Designed for use as a washdown pump
and/or circulate water to your livewell
tank(s). Heavy duty construction for use
in commercial or pleasure boats.
• 1-1/2" inlet & 1-1/2" discharge outlet.
NON-AUTOMATIC
Stock #
Capacity
RUL17A.................3800 GPH 12V
RUL18A.................3800 GPH 24V
RUL19A.................3800 GPH 32V
Call Toll Free: (800) 426-2783 8-5 M-F
Rule-Mate Bilge Pump
Automatic, impressive pumping power for its
size and cost. Competitive models in this
pumping range are much larger & more
expensive.
Fitting:
Size:
1 1/8" Discharge outlet...........1100 GPH
Stock #
Description
RULRM1100 .........Pump Rule-Mate 12V
Rule-Mate Bilge Pump - 750 GPH
Automatic, increased capacity in keeping
with its 3/4" design.
Fitting:
Size:
Discharge outlet...............750 GPH
Stock #
Description
RULRM750 ...........Rule-Mate Auto 12V DC
Rule-Mate Bilge Pump
Many design features with low cost. Especially
popular on small craft. Unmatched for power &
longevity for it's size.
Fitting:
Size:
Discharge outlet...............500 GPH
Stock #
Description
RULRM500 ...........Rule-Mate Auto 12V DC
Seattle: (206) 285-5010 Fax: (206) 285-7925
310
Rule Pumps
Pumps & Plumbing
Rule 4000 GPH
Designed for the toughest applications. The Rule
4000 pump optimizes exclusive design features
to produce the highest capacity available for a
pump its size.
• 2" discharge outlet.
NON-AUTOMATIC
Stock #
1500 GPH Bilge Pump
More pumping capacity & design features than any
comparable competitive pumps.
1 1/8" discharge outlet.
NON-AUTOMATIC
Stock #
Capacity
RUL02....................1500 GPH
Capacity
RUL56D.................4000 GPH
3700 GPH Bilge Pump
Heavy duty construction for both commercial &
pleasure boat use.
Known for trouble free operation & reliability.
NON-AUTOMATIC
Stock #
Capacity
RUL14A.................3700 GPH 12V
RUL15A.................3700 GPH 32V
RUL16A.................3700 GPH 24V
2000 GPH 5 Year
Advanced features throughout supported with an exclusive 5 year warranty.
• Rule manufactured motor for superior quality.
• Double insulated long stack motor.
• Heavy duty 5/16" stainless steel shaft.
• Extra strong nylon/fiberglass impeller.
• Heat resistant acetal resin housing.
• Triple straining system to virtually eliminate clogging.
NON-AUTOMATIC
Stock #
Capacity
RUL09....................2000 GPH
RUL10
8000 GPH Bilge Pump
Rule's largest capacity submersible
pump. Incorporates two 4000 GPH
pumps which discharge through a
common 3" discharge outlet.
Since the 2 pumps function independently, if one pump fails, the other will
continue to operate for back-up pumping capability.
• Replacement motor modules available.
NON-AUTOMATIC
Stock #
Capacity
RUL174D...............8000 GPH
2000 GPH Bilge Pump
Engineered to commercial standards.
Best selling high capacity submersible
bilge pump in the world.
NON-AUTOMATIC
Stock #
Capacity
FULLY-AUTOMATIC
Stock #
Capacity
RUL10....................2000 GPH .............12Volt
RUL11 ....................2000 GPH .............32Volt
RUL12....................2000 GPH .............24 Volt
RUL53S .................2000 GPH ..............12 Volt, 3 wire
RUL53S
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
311
Rule Pumps
1100 GPH Bilge Pump
Automatic. Impressive pumping power for it's
size & cost. Competitive models in this range
are much larger & far more expensive.
Stock #
NON-AUTOMATIC
Stock #
Description
RUL27S-3 ..............Pump Auto1100 GPH 12v 3WR
Capacity
RUL20F .................800 GPH Square
RUL20R .................800 GPH Round
360 GPH Bilge Pump
Economically priced & designed for small boats.
Pumps & Plumbing
800 GPH Bilge Pump
2 different 800 GPH models, traditional square version
& a round version.
Both square & round pumps have 3/4" discharge outlets.
Square model:
• Offers 36 mounting variations.
• Is equipped with gasoline resistant strainer base.
NON-AUTOMATIC
Stock #
Capacity
RUL24....................360 GPH
Bilge Pump 1000 GPH
Popular choice of boatbuilders & boat owners
alike.
• Offers 36 mounting variations.
• Equipped with gasoline resistant strainer base.
500 GPH
Unmatched in pumping power & longevity for
its size. Popular on smaller craft. 3/4" discharge
outlet.
NON-AUTOMATIC
Stock #
Capacity
RUL20A.................1000 GPH Square
NON-AUTOMATIC
Stock #
Capacity
RUL25D.................500 GPH
1100 GPH Bilge Pump
Lots of pumping power in a very small space.
NON-AUTOMATIC
Stock #
Capacity
RUL27D.................1100 GPH
Pump Thru Hull
"FC" Tournament series TM removable motor
cartridge.
For thru-hull uses - Straight 4 3/4" (121m)
Pickup tube.
• Flow rate: 800 GPH
3028 Iph.
• Discharge: 3/4"
19mm
• Vo l t a g e : 1 2 V d c - A m p d r a w : 2 . 8 A m p
Fuse size: 5.0 Amp
Stock #
Pool Cover Pump with Leaf Protector.
The finest pool cover pump ever designed.
Features:
Powerful 110 volt 1800 GPH automatic
submersible pump with a specially designed
strainer base that filters out leaves & debris.
Installs easily with garden hose.
Stock #
Description
RULH53SP24 ........Pump 1800 for Pool Cover 110V
-
Description
RUL403FC.............Pump Thru Hull Mount 800 GPH
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
312
Rule Pumps
110 Volt Pumps - Marine & Non-Marine Uses
Designed to remove water from basements, garages, stairwells, utility rooms, back yards,
sumps, pools, pool covers, boats & other utility applications.
Fully-automatic versions utilizing standard 110 volt AC current.
Pumps & Plumbing
Fully Automatic
Stock #
Capacity
Features
RULA53S ..............1800 GPH ..............8' cord,
Includes garden hose adapter & rigid pipe adapter, #57.
RULA53S-24 .........1800 GPH ..............24' cord,
Includes garden hose apapter & rigid pipe adapter, #57.
Parts
RUL57....................90 degree rigid pipe adapter for 1800 1" NPT
RUL58....................90 degree rigid pipe adapter for 2800 1-1/8" NPT
RUL68....................Garden Hose Adapter
Hose Adapters
Designed to be used with Rule pumps & thru-hulls.
Heavy-duty molded, non-corrosive, high impact plastic.
Stock #
Description
RUL57 Elbow Adapter 1-1/8” - 1”
RUL58....Elbow Adapter 1-1/2”- 1-1/4”
RUL61....Thru-Hull 3/4” Right Angle Plastic
RUL64....Adapter Switch 3500 Pump
RUL65....Adapter Switch 1500, 2000 Pump
RUL66....Bracket for Pump
RUL67....Adapter Straight 1-1/2”- 1-1/8”
RUL68....Adapter 1-1/8” X GARDEN HOSE
RUL69....Adapter Straight Double Stepped
RUL70....Strainer SS
RUL73....Strainer Livewell 3/4” NPS SS
RUL67
RUL57
RUL58
RUL68
RUL69
RUL64
RUL65
Thru Hull Straight Fitting 3/4"
High impact plastic will not rust, corrode or discolor.
Specially designed for Rule pumps.
Stock #
Description
RUL61S .Thru-Hull 3/4” Straight Plastic
Thru Hull Straight Fitting 1-1/2"
Stock #
Description
RUL59....Thru-Hull 1-1/2” Straight Plastic
RUL60....Thru-Hull 1-1/8” Straight Plas
RUL72....Thru-Hull 2” Straight Plastic
Call Toll Free: (800) 426-2783 8-5 M-F
Thru Hull Angle Fitting 5/8"
Stock #
Description
RUL62....Thru-Hull 5/8” Right Angle Plastic
Seattle: (206) 285-5010 Fax: (206) 285-7925
313
Rule Switches
Rule switches offer quality features:
• Improved wire for greater durability & water resistance.
• Ultrasonic welding assures perfect hermetic seal.
• No battery drain.
• No exposed metal to corrode.
• Ignition protected.
Stock #
Description
RUL40A.................Non-Mercury with Guard
Stock #
Description
RUL41....................12V DC
RUL42....................24/32V DC
Standard
3-Way Panel Switch
Black, stainless steel panel.
Similar to deluxe panel switch but without
indicator light or fuse holder.
Manual position has fail-safe spring return
to "Off" can't accidentally leave pump running.
Stock #
Pumps & Plumbing
Rule-A-Matic Plus™ Float Switch
Strong, fully integrated, impact resistant cover.
Highly abrasion resistant wires exit the top, keeping them out
of the water and keeping wear and tear to a minimum.
• Dual-lever and anti-clog water slots for unique level of
performance & protection.
• Manual testing feature for operations check.
• Available in fused & unfused versions.
• For use with pumps up to 20 Amps.
Deluxe 3-Way Panel Switch
Controls any pump equipped with an automatic float switch.
• Toggle has 3 positions.
• Automatic/Off/ Manual, and a spring return
to off position from manual position.
• Black stainless steel panel.
• Red indicator light. Fuse holder.
Description
RUL45....................3-Way Panel Switch
Super Switch
Evironmentally responsible. Completely sealed metal
capsules enhance flawless operation.
• Designed for the toughest needs.
• Use with pumps drawing up to 20 amps.
Stock #
Description
RUL37A.................Super Switch, non-mercury
RUL37FA ...............Super Switch with Fuse, non-mercury
Rule-A-Matic Switch
Switch of choice by yachtsmen, commercial fishermen &
boat builders the world over, makes Rule-A-Matic the
largest selling switch in the world.
Stock #
On/Off Panel Switch
Attractive black stainless steel panel.
High lights control panel. Simple "On/ Off"
positions provide fingertip control.
Stock #
Description
RUL49....................Panel Switch
3-Way Rocker Panel Switch
Unit features a black plastic panel.
• Built-in fuse holder.
• Internally lighted rocker switch. 3 positions:
Automatic/Off/Manual with "fail-safe."
• Spring return to "Cff" from manual position.
Stock #
Description
RUL43....................3-Way Rocker Switch
Descxription
RUL35A.................Non-Mercury Switch
RUL35FA ...............Non-Mercury w/ Fuse
Bilge Pump Counter
Electronically counts number of times bilge pump switches.
• Bright LED digital readout. Reset button.
• 1 second delay compensates false counts from waves & rocking.
• Switch: Auto On/Off /Man, green "On" light, fuse holder.
• Use with Aqualarm Smart Bilge Pump Switch (part # 20038).
Stock #
Hi-Water Bilge Alarm
Components are a float switch & in-dash gauge with both
visual & audible alarm.
• Unmanned compartment can be constantly monitored.
• For more compartments add additional model 33 float
switch.
Stock #
Description
RUL33AL ..............12V DC
RUL31AL ..............32V DC
Description
AQL20045 .............Bilge Pump Counter
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
314
Pump Accessories
Replacement Strainer Base
Original replacement strainer base for Rule pump.
Round Rule pumps, 1500 to 2000 GPH.
Hydro Air Switch for Bilge & Sump
Stock #
Stock #
Description
Pumps & Plumbing
JAB59400-0012 .....Switch Hydro Air 12V Bilge/Sump
Rule Side Mount Brackets
Permits small Rule bilge to be side mounted to
a vertical stringer, bulkhead or transom. Use
bracket when bottom mounting is inconvenient
or impossible. Simply remove strainer from the
pump, put bracket in place & reassemble.
Stock #
Description
Description
RUL278..Strainer..Red....#10 #02 #09 #11
Livewell Pump Debris Strainer
Attach directly to any pick-up tubes on Rule Livewell
Pumps. Filters out trash & debris that could clog pump.
Stainless steel wire mesh, 3/4" female NPS threads.
Stock #
Description
RUL73....Strainer Livewell 3/4” NPS SS
GPH
RUL66......Bracket......Round Pumps from 360 to 1100 GPH
Rule Stainless Steel Debris Strainer
Extra protection on round based Rule pumps up to
3700 GPH. Installs directly into existing strainer.
Filters out excess debris & helps prevent jamming
& failure.
Foot Galley Pump
Injection molded delrin.
• Uses 1/2" hose.
Stock #
Stock #
GPM
Description
RUL70....................Strainer SS
SDG517060-3 ........3
Fresh Water Inlet
Chrome plated brass. Display pack.
• Standard female hose connection.
Stock #
Base
SDG512110-1 ........2-3/4"
Washdown Outlet
Garden hose hookup to onboard water system.
• Standard male hose connector.
• Display pack.
Stock #
Base
SDG512120-1 ........2-3/4"
Shower Drain System
A compact full capacity shower drain system that automatically starts & shuts off as
water flows. Activated by a Rule-A-Matic
float switch.
• Choice of single or 3 inlet ports that offer a variety of combinations of
inlet hose.
• A clear screw down cover, removeable strainer.
• An internal check valve to prevent back flow.
8-1/4"L x 11-1/4"W x 5-1/2"H. Has multi-port fittings of 3/4" - 1" - 1-1/8" - 11/2"
Stock # ...........Description
RUL98....Multi-Port Inlet 12v 800GPH
Water Inlet Fitting
• Obtaining water at dockside.
• Chrome plated bronze. Watertight black plastic plug.
• Standard female swivel hose connector.
• Stainless steel bead chain.
Stock #
Description
Pipe Size
OD Flange
Marine Shower System
• Shower box with 10ft spray hose & fittings.
• Chrome spray head with water conservation button.
• Flush mount. Surface area 6" x 10.25", depth 4".
• UV stable material. 2 year warranty.
Stock #
Description
HTC303SB......Shower Unit Only 3S
PRK499DP....Fitting Water Inlet... 1/2"......2-3/4"
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
315
Groco Heads/Water Pressure Systems
Fitting:
Length:
Stock #
Description
Width:
Height:
Stock #
Description
GRCHFB ...............Toilet Hand Pump Bronze Base
GRCHFMASTER ..Toilet Service Kit HF Master
GRCHF10 ..............Piston And Ring Assy HF Toilet
Pumps & Plumbing
SweetTank Odor Neutralizing System
Stops odors without use of chemicals or filters.
Sweettank introduces a constant flow of air into the
holding tank through a submerged aeration tube, an
oxygen rich environment is produced where bacteria
cannot thrive!
• Compact module operates continuously.
• Screws into 1-1/2" threaded fitting on top/side of tank or a 2-1/2"
hole cut in tank top/side. Mounting hardware included.
• Uses less than 3 watts of DC power. AC option available.
Toilet HF- Groco
• Sturdy bronze base for rough water use.
• T-handle for ease of operation. Weighs 32 pounds.
• High-efficiency valve system uses minimal flush water.
Hose Connection:
1-1/2"NPT” threaded ........5.30"...........4.00...........2.38.........3/16"ID
GRCSTK-18-12V ......Sweettank 12V Odor System.
Toilet KH -Groco
• 3" bronze piston pump
• House sized bowl Weighs 44 pounds.
• Heavy duty
Stock #
Description
Weight
GRCKH ...................Toilet Hand Pump...44Lb
GRCKREGULAR ...Toilet Service Kit
GRCK32 ..................Piston & Ring Assembly
Water Pressure System - Paragon Junior
For mid-size yacht up to 50 Ft.
• Compact & powerful 2-stage pump.
• Pressure gauge & 3/4" strainer included.
• Patented NOFLO dry-run protection.
Stock #
Description
GRCPJR12V ..........Paragon Junior 12v
GRCPJR24V ..........Paragon Junior 24v
Tecma Silence Plus
Elegant European design, household
size bowl. All porcelain, with molded
plastic seat and cover. Heavy duty centrifugal discharge macerating pump.
Extremely quiet operation. Uses
on-board pressure water or optional
seawater intake. 2 year warranty. Has
3/4" intake and 1-1/2" discharge.
• House sized bowl. Weighs 62 pounds.
• Heavy duty.
• Seat height 18".
• Width 15", depth 21".
Stock #
Description
WIC301000 ............Tecma Toilet 12v Standard
WIC38101 ..............Tecma Toilet 12v Plus
Water Pressure System - Paragon Senior
For mid-to large size vessels over 50 Ft.
• Compact & powerful 2-stage rotary pump. Easy install.
• Pressure gauge & 3/4" strainer included.
• Patented NOFLO dry-run protection.
Stock #
Description
GRCPSR12V .........Paragon Senior 12V
GRCPSR115VAC ..Paragon Senior 115V
Call Toll Free: (800) 426-2783 8-5 M-F
Liquid Level Gauges
Level gauge for fuel, oil or water.
Murphy Switch.
Stock #
Description
HOUEL150K1 .......Complete Unit
HOU15000100 .......Rebuild Kit
Seattle: (206) 285-5010 Fax: (206) 285-7925
Pumps & Plumbing
316
Jabsco Waste System & Parts
37010-0090
Electric Marine Toilet
Electric marine toilet is available with either:
• Compact white vitreous china bowl.
• Larger yacht-size bowl with standard house seat/lid.
Larger size ideal for larger vessels and pleasure yachts.
Dual function pump:
• Eliminates using hand pumps and dry bowl valves.
• Push button, self-priming flush pump rinses bowl as
macerator and high capacity scavenger pump grind up
waste and pump it out. 0090 is Compact bowl, 1090 is Household bowl.
Includes:
• Heavy duty push-button switch.
• Inlet 3/4" - Outlet 1". 1" to 1-1/2" hose adaptor for discharge hose.
Stock #
Volt
Amp
Fuse
Height
Width
Parts: JAB37010-0090
Length
JAB37010-0090 .....12............18............25............13-3/4" x 13-7/8" x 17-5/8"
JAB37010-0096 .....24............18............25............13-3/4" x 13-7/8" x 17-5/8"
JAB37010-1090 .....12............18............25............14-3/8" x 14-5/8" x 19-3/4"
Parts: Jab37010-0090:
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
317
Jabsco Marine Waste Systems
Flush cycle similar to household toilet.
Extremely quiet flush cycle. Variation of 37010-series electric toilet
but utilizes existing on-board pressurized water system for bowl rinsing.
Multi-function control pane, select:
1. Normal flush cycle, by a single push button switch.
2. Bowl-fill/bowl-empty, by a double throw rocker switch.
Compact size for tight spaces or larger yacht size: standard household type seat/
lid assembly. Operates with salt or fresh water.
• Bowl of easy-to-clean white vitreous china.
• Connects to pressurized water source: 3 1/2 gallons of water per/minute.
• Anti-siphon breaker valve: prevents contaminating vessel's potable water.
• Electric solenoid valve: controls toilet water supply.
• Powerful macerator discharge pump evacuates bowl.
• 6 feet of white hose connects toilet bowl fittings to remote mounted solenoid
valve & siphon breaker assembly. Compact is 13 3/4"Hx14"Wx17 1/2"D
Regular is 14"Hx14 1/2"Wx19 1/4"D.
Regular
Compact
Pumps & Plumbing
Quiet-Flush Toilet
Compact
Stock #
Volts
10 Psi
Fuse/ Breaker*
Volts
10 Psi
Fuse/ Breaker*
JAB37045-0092 .....12 V DC .18............25
Regular
Stock #
JAB37045-1092 .....12 V DC..18............25
Models available in: 12, 24 & 32 V DC.
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
318
Pumps & Plumbing
Jabsco Marine Waste Systems
Parts: Jab29090-2 & 29120-2:
Manual Marine Toilet - Jabsco
Manual toilet offers smoother contoured lines.
Pump assembly is angled forward for smooth stroke action.
Easier to clean.
All black rubber gasket edges are concealed from view.
• Plastic polypropylene parts are strong/resistant to most
chemicals & cleaning supplies.
Unscrew to remove as an assembly, entire handle &
seal housing, piston rod & piston without disassembling pump.
Quick/easy priming.
Upper flap valve assembly fitted with valve return spring.
• Full size rod guide & seal housing:
• Light gray pump handle & wet bowl-dry bowl selector lever.
• Top-mounted 'Dry Bowl' selector is easier to operate.
• Pump & base can be assembled for left-hand operation.
• Available in compact size or household size bowl & lid.
Stock #
Bowl Size
Depth in.
Width In.
Height In.
Wt. Lbs
JAB29090-3000 .....Compact .16 3/4" ....17 3/4" ....13 3/16"...26 Lbs.
JAB29120-2000 .....House .....19 5/16"...18 5/8" ....13 5/8" ....21 Lbs.
Repair Kits:
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
319
Marine Waste Systems
Electric Flush Pump
Converts all PAR manually operated toilets to
convenient electric operation.
Flush pump: is self-priming & may be installed on
toilets mounted as high as 3 feet above waterline
without requiring a check-valve in the inlet hose.
Flush Pump
Stock #
Volt
Amp
Fuse
Std. Ctn.
JAB29200-0120 .....12............24............25............1
Macerator Pumps
A rotary cutter shreds waste before it is pumped
into or out from the holding tank. The pump
should be connected as close as possible to
the holding tank discharge outlet or the bowl
discharge outlet.
The motor has built in thermal protection reducing the risk of damage when the pump is run dry.
12v, 15 amp. 1-1/2" hose or 1-1/2" NPT inlet. 1" hose outlet
Stock #
Pumps & Plumbing
Discharge pump: will operate effectively against
vertical discharge heads up to 3 feet.
Typical flush cycle completed in less than 10 seconds
with a minimal amount of water.
Electric Toilet Base Assembly
Self-priming flexible flush pump rinses bowl as powerful
macerator scavenger pump grinds up & pumps out waste.
• Built in backflow preventer is included in discharge.
• Heavy-duty push-button switch.
• 1" to 1-1/2" hose adaptor for discharge port.
• All clamps/fasteners to complete conversion (included).
• Inlet: 3/4". Discharge:1".
• Weight: 12-1/2 Lb - (5.7 kg).
Description
JNP102445301 .......12V Macerator
Stock #
Volt
Amps
Fuse
JAB37010-0092 .....12............18............25
JAB37041-0010 .....12............Replacement Pump
JAB37010
Macerator Pumps
Ideal for simple holding tank pump-outs.
Grinds waste into small particles to easily pass
through
1" hose barbed discharge port.
• Self-priming & can empty a typical 30 gallon
holding tank in less than 3 minutes.
• Sealed bearings & hard durable powder coating to prevent
corrosion occuring both internally & externally.
• 4-bladed chopper added to further reduce possibility of clogging.
• Run-dry feature present in previous models.
• Automatic shut-off & sensor for priming pump.
JAB37041
• Macerator has an inlet port with both:
1-1/2" hose barb for easy attachment to waste hose.
1-1/2" male pipe thread to screw directly into a tank flange or other pipe
fitting.
NOTICE: Do not discharge waste overboard unless very certain you are
beyond the 3 mile coastal limit & are not in an area designated as
"No Discharge Zone".
Stock#
Flow (GPM) Volts
Amps
Fuse
Dimensions
Wt.
JAB18590-2092 .....13............12............15............20............3 3/8"H x 4 5/8"W x 11"L
JAB18590-2094 .....13............24............8..............10............3 3/8"H x 4 5/8"W x 11"L
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
320
Head Accessories
Pumps & Plumbing
SEACLO Repair Kits
All the necessary parts to put a Seaclo in A-1 condition.
Kits contain:
• Cup leathers, flap valves, gaskets,
• Packings & screws, check valve ball.
• Discharge backwater check (Joker) valve.
• Inlet valve packing & spring.
Stock #
Description
WIC1599 ................For Junior #51, Regular #51, Crown #51,
Sanette #51, Sea-Pup, & Imperial #51
WIC1520 ................For Head-Mate
WIC1539 ................For El-Seaclo, & Skipper
Pump Cylinder Assembly for Toilet 29090
Stock #
Description
JAB29051-0000 .....Pump Cylinder Assembly F/29090
JAB29051-2000 .....Pump Cylinder Assembly 29090
Bronze HVL Vented Loops
Allows air to enter to break siphon but does not
permit air & odors to escape. Assures clog free
anti-siphon protection.
• If used in exhaust system, overboard venting
required.
Stock #
Pump Assembly for 29090 Toilet
Stock #
Hose ID:
Weight
Pkg.
Description
JAB29040-3000 .....Pump Assembly for 29090 Toilet
Vented Loop
Marelon molded - Neither loop nor vent will
corrode.
Simple valve system in top allows air to enter
line when not in use, yet seals as water or fluid
passes through.
Stock #
Service Kit Major for Toilet
Stock #
Description
GRCHVL1500 .......Vented Loop for.....1-1/2”.....1.8 Lbs....2.
GRCHVL750 .........Vented Loop for........3/4”.....2.6 Lbs....2
Description
Description
FPR903000 ............Vented Loop 1 1/2” Marelon
FPR903001 ............Vented Loop 3/4” Marelon
FPR903009 ............Vented Loop 1 1/8” Marelon
JAB29045-0000 .....Service Kit Major for Toilet
Vented Loops
An essential safety component on all inlet & discharge
plumbing of toilets installed below static or heeled
water line.
• Internal valve avoids need for external venting.
• Fitting connections for 1".
Stock #
Description
JAB29015-0020 .....Vented Loop 1” Hose Plastic
Call Toll Free: (800) 426-2783 8-5 M-F
Y Valve for Toilet Waste
Robust Y valve allows waste to be pumped
overboard or into a holding tank. Waste &
corrosion resistant.
• Rotating parts allow variable routing of
hoses on valve.
• Optional handle extension allows operation
through bulkhead.
• Can be padlocked to insure local regulations are met.
1-1/2" Inlet or 1 "outlet.........7-5/8" Long x 7 1/4" W x 4 1/8" High
Stock #
Description
JAB45490-1000 .....Y Valve 1 1/2” for Waste
Weight
2 Lbs.
Seattle: (206) 285-5010 Fax: (206) 285-7925
321
Thetford Heads
Stock#
Pumps & Plumbing
ComfortMate Manual Flush
Permanent marine toilet.
The ComfortMate toilet offers a revolutionary new design
that combines best-in-class comfort with a compact footprint
and residential styling.
• Powerful Nozzle Flush for robust flush coverage.
• Adapts for right or left handed installations.
• Easy to clean full China bowl.
• Easy to use pump mechanism with easy grip handle.
Description
THE41160 ..............Manual Toilet
Porta Potti 235
Positive lock lid latch keeps lid secure during transporting.
Waste holding tank level indicator shows when tank is full.
• 12-1/8" height makes toilet ideal for boats with V-berth.
Stock#
Description
THE25103 ..............Porta Potti #135 - No Gauge
Thetford: 135
All Thetford Portable Toilets have:
• Pump out connections odorless and leakproof.
• Own fresh water supply for flushing.
• 3 year warranty reliable for years of trouble free service.
Porta Potti MSD 365
Piston-pump flush features:
• Level indicator tells when time to empty.
• Big 5.5 holding tank, max use before emptying.
• Special hold-down brackets secure head to floor/deck.
Color: Beach white with dove-brown accent band.
Stock #
Description:
THE25109 ..............Porta Potti #365 MSD
Porta Potti 365
Portable toilet, piston pump flush.
• Big 5.5 holding tank, max uses before emptying.
• Carries a 3 year warranty!
• Level indicator tells when it's time to empty.
• Lid latch secures seat & lid.
Stock #
Description:
THE25112 ..............Porta Potti #365 White / Pump
Porta Potti MSD 465
Electric flush - Features:
• Top of line MSD, powerful battery flush, very easy.
• Fingertip control of flush strength, length & water use.
• Big 6.1 holding tank, max uses before emptying: 62.
• Special hold-down brackets secure head to floor/deck.
Stock #
Porta Potti 345
Portable toilet, piston pump flush.
• Carries a 3 year warranty!
• Level indicator tells when it's time to empty.
• Lid latch secures seat & lid.
Stock #
Description:
THE25113 ..............Porta Potti #345
Description:
THE25110 ..............Porta Potti MSD 465
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
Pumps & Plumbing
322
Head Chemicals
Supreme Green Odor Control
Convenient pre-measured packs: Non-dusting granules
• Very best odor control - Formaldehyde-free!
• Powerfull all-season control - 100% biodegradeable.
• Fast breakdown of solids, prevents tissue clogging.
Stock #
Description
THE28774 ..............Supreme Green Dry 8 - 2 Oz Pkg
Aqua-Kem® Holding Tank Deodorant
Concentrated, non-staining liquid holding tank deodorant
• Eliminates waste odor.
• Liqufies waste fast.
• Helps break down toilet tissue.
• Fast, effective action around the clock.
• Detergent additive keeps tank clean.
• 100% biodegradable.
• Environmentally safe when disposed
of in a waste treatment system.
Use in all RV & Marine portable, permanent
& recirculating sanitation systems.
Stock #
Description:
THE09852 .............Aqua-Kem 32 oz
THE24260 .............Aqua-Kem 64 oz
Potty Bucket Seat Only
Handy & easy to clean. White poly seat fits
3 or 5 gallon bucket (not included).
Stock #
Dri-Kem Holding Tank Deodorant
Concentrated dry, granular holding tank deodorant.
Uses: all RV/Marine portable/permanent & recirculating
sanitation systems.
• Long-lasting odor control, biodegradable.
• Fast acting, easy-to-use non-dusting granules.
• Environmentally safe when disposed in waste
treatment system.
• Convenient water-tight packs. 8 packs per carton.
Stock #
Stock #
Description:
THE03300 .............2-ply Tissue 4/pkg
THE20804 ..............1-ply Tissue
Aqua-Kem Holding Tank Deodorant
Concentrated liquid liquefies waste & controls odors .
Stock #
Description
Size:
THE24453 ..............Aqua-Kem... 3-8 Oz. Bottles Per Bx
Call Toll Free: (800) 426-2783 8-5 M-F
Packets per Box
THE20720 .............8 ea 2 oz
THE36535 ..............Toss-ins Aqua-kem Foil Pouch
Holding Tank Deodorant - Supreme Green
Very best odor control - Formaldehyde-free!
• Powerfull all-season control - 100% biodegradeable.
• Fast breakdown of solids, prevents tissue clogging.
• 4 Oz treats 40 gallons!
• Environment safe when disposed of properly.
Stock #
Aqua-Soft® 2-Ply Rapid Dissolve Toilet Tissue
Luxurious 2-Ply toilet tissue - Won't clog drains.
• 500 sheets per roll, 4 rolls per pack.
• Specially formulated, rapid dissolving tissue.
• Suitable for use in septic systems.
• Helps prevent messy clogs.
• Flushes easily from bowl.
100% Biodegradable
• Made from 100% recycled paper (20% post consumer).
• Soft, snowy white tissue.
Uses: all RV/Marine portable, permanent & recirculating
sanitation systems.
Description
TOD800201W........Bucket Potty White
Description
THE28736 ..............Supreme Green 36 Oz
Aqua-Zyme® Enzymatic Waste Digester
Environmentally safe liquid enzymatic waste digester.
• Naturally breaks down waste in holding tanks.
• Dissolves fats and oils in drain traps & plumbing lines.
• Fresh outdoor fragrance. Non-toxic, non-corrosive.
•100% Biodegradable.
• Environmentally safe when disposed of in waste
treatment system.
Stock #
Size:
THE13292 .............32 oz
Aqua-Bowl Bathroom Cleaner
Multi-purpose bathroom cleaner. Cleans and freshens
toilets, tubs, sinks, and showers.
• Non-abrasive, non-scrub cleaner. Does not scratch.
• Ideal for plastic, fiberglass & porcelain surfaces.
• For RV, boat and home.
• Thickened formulation clings to soiled surfaces.
• 100% biodegradable.
• Environmentally safe when disposed of in waste
treatment system.
Stock #
Size:
THE03610 .............32 oz.
Seattle: (206) 285-5010 Fax: (206) 285-7925
323
PAR Marine Blowers
PAR Marine Blowers
A versatile means of exhausting:
• Warm air from galleys & engine rooms.
• Ventilating odors or steam from heads.
• General marine air circulation.
Built of tough reinforced plastic housing & one-piece balanced plastic
rotor for maximum corrosion resistance in marine environments.
Sizes: 100 to 250 cubic Ft. per minute of air movement satisfies most reqs.
Flex mount
Flange mount
Flange Mount Blowers
Generally mounted with discharge port fastened directly to flat external surface to minimize required ducting.
Inlet port can be connected with duct hose to area requiring ventilation.
Air Flow
Stock#
JAB34744-0000
CFM
100
CUCM/
sec
47,200
Volt
- Fuse Amps
Brkr.
115 AC .70
.75
In
3"
Out
- Dimensions -
2-3/4"
7-5/8"
6-5/8"
7"
L
Weight
4 Lb.
H
W
Pumps & Plumbing
Installation versatility provided by either:
• Flex mount (motor attached mounting bracket) or
• Flange mount (mounting flange on discharge port) models.
• Blowers up to 150 CFM have 3" ports; 250 CFM models have 4" ports.
5 Lb.
JAB35115-0020 .....105..........49,600.....12 DC .....4.3...........6
3"
2-3/4"
5-1/2"
4-3/4"
6-3/4"
JAB34739-0031 .....140..........61,500.....115 ...........0.8..........1.25
3"
2-3/4"
5-1/2"
4-3/4"
6-3/4"
JAB34739-0010 .....150..........70,800.....12 DC .....6.5...........10
3"
2-3/4"
7-5/8"
6-5/8"
8"
5 Lb.
JAB35400-0000 .....250..........118,000 ...12 DC .....12............15
4"
3-5/8"
9"
8-3/4"
8-3/4"
6 Lb.
Flex Mount Blowers
Inlet and outlet ports designed for slip-on flexible duct connections.
• Ideal for "in-line" installation of a blower.
• May be rotated in mounting bracket to permit installation with discharge port in any direction.
• Meet applicable sections of U.S. Coast Guard Electrical Regs:
[Title 33, Chapter 1, Part 183, Subpart 1] & listed as N.M.M.A. type accepted.
Air Flow
sec
Volt
- Dimensions -
JAB35515-0010 .....105..........49,600.....12 DC .....4.3...........6
3"
Out
3"
5-1/2
5
6-3/4
L
Weight
JAB36740-0000 .....150..........70,800.....12 DC .....6.8...........10
3"
3"
9 1/8
8 3/16
8
5 Lb.
JAB35440-0000 .....250..........118,000 ...12 DC .....12............15
4"
4"
9 5/8
9 1/4
8 3/4
7 Lb.
CFM
CUCM/
- Fuse Amps
Brkr.
In
Stock#
Rule In-Line Blowers
Efficient, high output operation, provides ventilation for
bilges, engine compartments, galleys & heads.
• Exclusive front & rear shaft seals & corrrosion resistant motor housings.
• Compact & easy install on any flat surface,
• Rule provid es higher air flow, lower amp draw & quieter operation.
• Slip on inlet & outlet ducting connections.
• Corrosion resistant nickel plated housing.
Ducting:
Voltage
CFM Open Flow
Amp Draw
Fuse Size
3"...............13.6...........135........................ 2.9................4
Stock #
Description
RUL140..Bilge Blower 3” Inline 12V
Ducting:
Voltage
CFM Open Flow
Amp Draw
Fuse Size
4"...............13.6...........235........................ 4.3................7
Stock #
Description
H
W
3 1/2 Lb.
Heavy Duty Flexmount Blower
Use as air intake or extraction systems in
engine rooms, fuel
compartments, galleys or heads.
• 5,000 hr. motor life at heaviest application.
Quiet Delrin rotors.
• Flex mounting 360° adjustable outlet.
Continuous duty.
• Slip on inlet duct connections. Low current
draw. High air volume.
4" ducting, 9" long x 9-1/2" wide x 9-1/4" high.
Stock #
Description
JAB35770-0092 .....Blower Flex Mount 250cfm
RUL240.........Bilge Blower 4” Inline 12V
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
Pumps & Plumbing
324
Valves
Sea-lect Y-Valves
Bronze Gate Valves
Divert liquids without costly fittings. Sea-lect is
a simple and compact Y-valve. Easy to use and
install.
Features:
Mount Y-valve almost anywhere, in seconds.
• Unique flush mount available on Model M-95.
• Simple design speeds connections & gives a
proper fit.
• Full-port opening; interior parts do not restrict flow.
• Corrosion resistant. Simpler & less expensive than alternative valves.
• Valve handle turns right or left to close off desired intake.
• Readily disassembled & reassembled for inspection/periodic cleaning.
• Removable travel stops convert from 2 to 3 way operation.
Base Mount
Working Pressure Non-Stick (PSI)
Saturated steam ......................125
Cold water, oil gas .................200
Stock #
BOSBM94A...........1/2" Y-Valve FIPT
BOSBM94 .............1" Y-Valve Hose
BOSBM95 .............1-1/2" Y-Valve Hose
Flush Mount
Stock #
Base
BOSM95 ................1-1/2" Y-Valve Hose
Flush
Standard
Stock #
BOS94A .................1/2" Y-Valve FIPT
BOS094 ..................1" Y-Valve Hose
BOS095 ..................1-1/2" Y-Valve Hose
Standard
Ball Valves
Brass body, large port, blow-out proof stem, screwed ends.
• Service in steam, water, oil & gas.
• 2 piece screwed type brass body in sizes:1/4" to 2", bronze body in sizes
2-1/2" & 3". Viton double O-ring stem packing.
• Zinc-plated hardened, plastic-covered lever handle remains cool in high
temperature installation. Hard chromium plated brass ball.
• Federal specs: WW-V-35, Type 11, Class A, Style 3.
Stock #
Hydrostatic Test Pressure (PSI)
Shell .......................................300
Seat.........................................200
Bronze Gate Valves
Stock #
Description
KIT27-012..............Gate Valve Bronze 1/2"
KIT27-100..............Gate Valve Bronze 1"
KIT27-112 ..............Gate Valve Bronze 1-1/2"
KIT27-114 ..............Gate Valve Bronze 1-1/4"
KIT27-200..............Gate Valve Bronze 2"
Bronze Check Valve
Working Pressure Non-Shock (PSI)
Saturated steam ......................125
Cold water, oil gas .................200
Hydrostatic Test Pressure (PSI)
Shell (water) ...........................300
Seat (air) .................................50
Stock #
Description
KIT22-012
Check Valve Bronze 1/2"
KIT22-034..............Check Valve Bronze 3/4"
KIT22-100..............Check Valve Bronze 1"
KIT22-112 ..............Check Valve Bronze 1-1/2"
KIT22-114 ..............Check Valve Bronze 1-1/4"
KIT22-200..............Check Valve Bronze 2"
Description
KIT68-014..............Ball Valve Brass 1/4"
KIT68-100..............Ball Valve Brass 1"
KIT68-114 ..............Ball Valve Brass 1-1/4
KIT68-112 ..............Ball Valve Brass 1-1/2"
KIT58-212..............Ball Valve Brass 2-1/2"
Inline Check Valves
Plastic inline valves for hose.
Stock #
Description
BOS074-6 ..............Inline Check Valve 3/4” Hose
BOS074 ..................Inline Check Valve 1” Hose
BOS074-10 ............Inline Check Valve 1-1/4” Hose
BOS075 ..................Inline Check Valve 1-1/2” Hose
Check Valve Spring Loaded
Bronze body. Stainless spring.
Stock #
In-Line Non-Return Valves
Fits in pumps suction hose to aid priming & prevent backflow.
1/4"or 1" or 1-1/2"......4-1/4" Long x 2-1/8" Wide x 2 " High
Stock #
Description
JAB29295-1000 .....Inline Check Valve 1”
JAB29295-1010 .....Inline Check Valve 1-1/2”
JAB29295-1011 .....Valve Inlet Nonreturn Chk 3/4”
Call Toll Free: (800) 426-2783 8-5 M-F
Description
RWH2321 ..............Check Valve Spring Loaded 1”
RWH232112...........Check Valve Spring Loded 1-1/2
RWH232114...........Check Valve Spring Loded 1-1/4
RWH23212 ............Check Valve Spring Loaded 1/2”
RWH2322 ..............Check Valve Spring Loaded 2”
RWH23234 ............Check Valve Spring Loaded 3/4”
Seattle: (206) 285-5010 Fax: (206) 285-7925
325
Seacock amd Ball Valves
Perko 825 Inline Valve
• Ball valve for smooth operation.
• Cast bronze.
• Complete with drain plug & bonding screw.
Stock #
Pipe/Size
Weight
Forespar MF 850 Series Ball Valves
• Precision molded in high strength glass-reinforced Marelon.
• Strength, light weight, & complete freedom from corrosion
& electrolysis.
• Ideal for controlling inlet/outlet water needs above/below waterline.
• Valves sold throughout U.S.A. have N.P. type threads.
• When installing, valves may be reversed in direction to provide
convenient handle position.
Perko 805 Seacock Body
• Ball valve design. Body is cast
bronze.
• Overall height is measured from top of
valve body to bottom of flange.
Stock #
Flange
Diameter
Overall
Height
Stock #
Pipe Size
Weight
PRK805005PLB ....3-1/4" ......3-3/8" ......3/4" ......... 2-1/2 Lb.
PRK805006PLB ....4-3/8" ......3-3/4" ......1" ............ 4
Lb.
PRK805007PLB ....4-7/8" ......4-1/4" ......1-1/4" ...... 5-1/8 Lb.
PRK805008PLB ....5-1/2" ......4-1/2" ......1-1/2" ...... 6-3/8 Lb.
PRK805009PLB ....5-3/4" ......5-3/4" ......2" ............11-3/8 Lb.
PRK805010PLB ....7-1/4" ......7-1/2" ......2-1/2" ......19
Lb.
PRK805011PLB.....8" ............7-3/4" ......3" ............24
Lb.
FPR905100
FPR905101
FPR905102
FPR905103
FPR905104
FPR905105
Thread
Size
Body
Dia.
Length
Length
w/ Handle
...........1/2" .........1-7/8" ......3" ............4"
...........3/4" ........1-7/8" ......3" ............4"
...........1" ...........2-3/4" ......4-3/4" ......5-1/2"
...........1-1/4" .....2-3/4" ......4-7/8" ......7-1/2"
...........1-1/2" .....3-1/2" ......5" ............5-3/4"
...........2" ...........4-1/4" ......5-7/8" ......8"
Forespar MF 849 Ball Valves
Stock #
Body
Pumps & Plumbing
PRK825004PLB ....1/2" .........1 Lb.
PRK825005PLB ....3/4" .........1-1/4 Lb.
PRK825006PLB ....1" ............1-3/4 Lb.
PRK825007PLB ....1-1/4" ......2-3/4 Lb.
Size
Height
w/Handle Base
FPR904009 ............1/2" .........3" ............4" ............3"
FPR904010 ............3/4" .........3" ............4" ............3"
Ball Valve 3-Way - Brass
Stock #
Description
KIT54-012..............Ball Valve 3-Way 1/2” Brass
KIT54-034..............Ball Valve 3-Way 3/4” Brass
KIT54-100..............Ball Valve 3-Way 1”
Brass
KIT54-112 ..............Ball Valve 3-Way 1-1/2” Brass
KIT54-114 ..............Ball Valve 3-Way 1-1/4” Brass
Brass
Brass
Call Toll Free: (800) 426-2783 8-5 M-F
Full-Flow Flanged Ball-Type Seacocks
• Handle installs in hard to reach areas.
• Easy retrofit. Tri-flange base & mount holes.
• Handle has square-hole for standard ratchet.
• Full pipe-size flow. Stainless steel ball & stem.
• PTFE seats & seals, serviceable while installed.
• Drain plug both sides for weatherization.
• Base with bonding attachment.
Stock #
Description
GRCSBV1250P .....Seacock Safety 1-1/4”
GRCSBV2000P .....Seacock Safety 2”
Seattle: (206) 285-5010 Fax: (206) 285-7925
326
Intake Water Strainers / Tail Pieces & Adapters
Pipe To Hose Adapters
Cast bronze.
Stock#
Pipe
Hose
Length
Size
Inches
Size
Inches
Overall
Inches
Weight
Pounds
Pumps & Plumbing
PRK76DP4PLB .....1/2 ...........5/8 ..........1-5/8 ........1/8
PRK76DP5PLB ....3/4 ...........3/4 ...........1-3/4........1/8
PRK76DP6PLB ....1..............1..............1-3/4........1/4
PRK76DP7PLB ....1-1/4........1-1/4........2..............3/8
PRK76DP8PLB ....1-1/2........1-1/2........2-1/4........1/2
PRK76009PLB .....2..............2..............2-5/8........1
PRK76010PLB .....2-1/2........2-1/2........4..............2 5/8
PRK76011PLB ......3..............3..............5-1/8........3 1/4
Pipe to Hose Adapters
Cast bronze. 90°. King Nipple.
PRK76 & 63 meet reqs. of :
U.S.C.G. Safety Standards, January 31, 1977
for gas fuel systems, 33CFR183.
Pipe
Stock#
Size
Hose
Size
Overall
Weight
Length
Pound
PRK63DP5PLB .....3/4 ...........3/4 ...........1-3/4........1/2
PRK63DP6PLB ....1 .............1 .............1-3/4........5/8
PRK63DP7PLB ....1-1/4........1-1/4........2 .............1-1/8
PRK63DP8PLB ....1-1/2........1-1/2........2-1/4........1-5/8
PRK63009PLB .....2 .............2 .............7 .............2-1/2
PRK63010PLB .....2-1/2........2-1/2........8-1/2........3-1/2
PRK63011PLB.......3 .............3 .............10 ...........6
Perko Intake Water Strainers
Designed for easy installation & cleaning.
Features:
• Mounting lugs cast into both sides gives universal mounting.
• 4 outside tie rods & 304 stainless steel strainer basket to
minimize electrolysis.
• Hinged lugs for cast bronze cover permit easy removal
& cleaning of strainer basket.
• Drain plug in bottom casting for easy removal of sediment
& draining for winterizing.
For uses requiring higher capacity see PRK500.
Spare Parts Ordering
For spare part # insert a spare part code listed below
in place of "PLB" in strainer's catalog number.
Stock#
Intake Water Strainer
Cast bronze construction. Easy installation & cleaning.
• Cast lugs on both sides for mounting.
• 4 outside tie rods. Drain plug to remove sediment.
• 316 stainless steel strainer basket to minimize electrolysis.
• Hinged lugs on cover for easy cleaning of basket.
Plain bronze:
Stock #
Pipe Size:
Height:
Weight:
PRK493004PLB .... 1 /2” ......5 3/4"H............4.9 Lbs.
PRK493005PLB .... 3/4” ...... 8 3/8"H............5.0 Lbs.
PRK493006PLB .... 1” ......... 9 1/2"H............8.1 Lbs.
PRK493007PLB .... 1-1/4 .........10"H........... 7.9 Lbs.
PRK493008PLB .... 1-1/2 ... 11-1/2"H......... 14.1 Lbs.
PRK493009PLB .... 2” .............16"H......... 18.0 Lbs.
PRK493010PLB .... 2-1/2”.........16"H......... 18.0 Lbs.
Description
99A.........................Top Casting
99B .........................Bottom Casting
PRK ........................Transparent Cylinder
PRK ........................Basket Strainer
99E .........................Cover with Gasket
99L .........................Hinged bolt for cover, pin, nut & washer
99N.........................Cover Gaskets (2 per bag)
99P .........................Tie rods, nuts & washers
Consists of:
(4 each tor 493 series)
(1 each for 500 Series)
Call Toll Free: (800) 426-2783 8-5 M-F
PRK493
HD Intake Water Strainer
Cast bronze construction. Easy installation & cleaning,
cast lugs on both sides for mounting.
• 4 outside tie rods. Drain plug to remove sediment.
• 316 stainless steel strainer basket to minimize electrolysis.
• Hinged lugs on cover for easy cleaning of basket.
Plain bronze:
Stock #
Pipe Size:
Height:
Weight:
PRK500009PLB .... 2”..........14-1/2"......36 Lbs.
PRK500010PLB .... 2-1/2” .. 16-1/2".......35.3 Lbs.
PRK500011PLB..... 3”.........18-1/2".......33.8 Lbs.
PRK500
Seattle: (206) 285-5010 Fax: (206) 285-7925
327
Water Strainers
Raw Water Strainer SA
Bronze body with plastic sight glass.
• Monel basket. Monel inside tie-rod.
• Wingnut spin-off. Fine-mesh filter basket available.
Dimensions: 12 3/4" High x 5.00" Wide.
Stock #
Description
GRCSA1250 ..........1-1/4" Strainer Monel Basket
Hose:
Stock #
Description
GRCSA2500.....Strainer 2-1/2”.... with Monel Basket
Hose:
Length:
Width:
Weight
2 1/2”NPT.......18.75"L...........6.25...........18.40 Lbs
Stock #
Description
Length:
Width:
Weight
3”NPT...............18.75"L.........6.25..........21.25 Lbs
Raw Water Strainer SE
For engines with 4, 5, or 6" intakes.
• Low restriction for cooling waterflow.
• Cover unscrews. O-rings seal all mating surfaces.
• Can be converted to hydromatic (Self-cleaning).
• #304 stainless steel filter basket.
Stock #
Description
GRCSE4000...........Strainer Raw Water 4” NPT
Hose:
Length:
Width
Weight
4” NPT.............18.4"L..........13.0...........97 Lbs.
Raw Water Strainer SEF
For high powered engines with 4, 5, or 6" intakes.
• Low restriction for cooling waterflow. No inside tie rods.
• Cover unscrews. O-rings seal all mating surfaces.
• Can be converted to hydromatic (self-cleaning).
• Monel filter basket. Bronze flange adaptors are
available to connect pipe/hose to flanged strainers.
Stock #
Description
GRCSEF4000 ........Strainer Raw Water 4” Flange
Hose:
Length:
Width:
Weight
4” Flange.............18.4"L.............13.0.............118 Lbs.
Stock #
GRCSEF5000
Hose:
Description
Strainer Raw Water 5” Flange
Length:
Width:
Weight
5” Flange.............18.4"L.............13.0.........134 Lbs.
Stock #
GRCSEF6000
Hose:
Description
Strainer Raw Water 6” Flange
Length:
Width:
Description
Basket Type:
Pipe Size: :
GRCARG750S.......Strainer Water ........SS Basket ...............3/4"
GRCARG1000S.....Strainer Water .......SS Basket ...............1"
GRCARG1250S.....Strainer Water .......SS Basket ...............1-1/4"
GRCARG2000S.....Strainer Water ........SS Basket ...............2"
GRCARG2015S.....Strainer Water .......SS Basket ...............2"
GRCARG3000S.....Strainer Water ........SS Basket ...............3"
GRCARG500 .........Strainer Water .......Monel Basket .........1/2"
Pumps & Plumbing
GRCSA3000......Strainer 3” ...with Monel Basket
Water Strainer
Magnifying cap for easy inspection.
• Unique mounting system allows for removal without tools.
• One piece molded sight glass eliminates tie rod & gaskets.
• O-rings seal all mating surfaces. Bond connection-both sides.
• Filter basket options: #304 (standard) Monel. Non-metallic.
Stock #
Accessories for Groco Water Strainer
Stock #
Description
GRCARG1 Service Kit Arg Water Strainer-for: 500-755-750
GRCARG2 Service Kit Arg Water Strainer-for: 1000-1250
GRCARG3 Service Kit Arg Water Strainer-for:1500-2000-2500- 3000
GRCARG1004....Bracket Bottom for: Arg1250s
GRCARG1005....Bracket Top for: Arg1250s
GRCARG506......Drain Plug Wing Nut with O-Ring
Water Strainer
Marelon molded, universal mounting
bracket & clear polycarbonate lid for ready
inspection.
• Stainless steeel strainer basket is easily
removed for cleaning.
• Mount bracket allows for correct position
of strainer exit port.
• Intake & exit ports are 1 1/2" ANP threads standard.
• (Available seperately) are reducers for 3/4" ID hose.
Dimensions: 6.3" Diameter x 6.1" Height.
Stock #
Description
FPR906066 ............Water Strainer1 1/2” Marelon
Weight
6” Flange.............18.4"L.............13.0.........147 Lbs.
Flange Adapter
Bronze flange adapters.
Stock #
Description
NPT:
GRCF4000 .............Flange Adapter for 4” NPT
Call Toll Free: (800) 426-2783 8-5 M-F
Intake Strainer
Cast Bronze
Stock #
Hose
Size
Tapered NPT Overall
Inches
Height
Diameter
Size
BUC00IWS1215...1 1/4"&1 1/2" ...............3/4"........4 1/2"..........6"
BUC00IWS150 ......1 1/2" ...........................1" ..........4 1/2"..........6"
Seattle: (206) 285-5010 Fax: (206) 285-7925
328
Fittings
Straight, Standard Flow King Nipple
Bronze
Stock #
NPT
#7550 Carbon Steel, High Pressure Ball Valves
Hose ID:
Weight
Pumps & Plumbing
GRCPTH750 .......... 3/4”......... x 3/4................. .20
GRCPTH1000 ........ 1” ........... x 1”................... .58
GRCPTH1125 ........ 1-1/8"....... x 1-1/4"............ .60
90° Standard Flow King Nipple
Bronze
Stock #
GRCPTHC1125
GRCPTHC1500
NPT
Carbon steel 1-piece body - Reduced bore.
Blowout-proof stem - Screwed ends.
Working Pressure Non-Shock (psi)
Saturated Steam .....................150
Cold Water Oil, Gas
1/2" - 1" ..................................2,000
1-1/4"-2" .................................1,500
Hydraulic Test Pressure
Stock #
Hose ID:
Weight
1-1/4"........1-1/8"................ .78
1-1/2”........1-1/2"................1.12
Size
RWH755012 ..........................1/2"
RWH755034 ..........................3/4"
RWH75501 ............................1"
RWH7550114.........................1-1/4"
Groco Multiple Port Raw Water Manifold Multiple fresh water uses from a single source.
RWM allows steady flow for main user & 3 intermittent users.
• Helps protect equipment.
• Total input volume is not exceeded by output volume.
• Installation instructions for proper pipe & hoses.
Stock #
Pipe
Hose ID:
GRCRWM1250...........1-1/4”.........1"
GRCRWM1500 ..........1-1/2”.........1-1/4"
GRCRWM1500-1 ...... 1-1/2”.........1-1/4"
GRCRWM2000 ......... 2”...............1-1/2"
GRCRWM2000-1 ...... 2”...............1-1/2"
GRCRWM2500 ......... 2-1/2”.........2"
GRCRWM3000 ......... 3”...............2-1/2"
King Nipple - Straight Full Flow - FF
Bronze
Stock #
Description
NPT:
Hose ID:
GRCFF500.......King Nipple ..................1/2” ....... 3/4”
GRCFF750.......King Nipple ..................3/4” .......1”
GRCFF1000.....King Nipple ..................1" ...........1-1/4”
GRCFF1125.....King Nipple ..................1" ...........1-1/8"
GRCFF1250.....King Nipple ..................1-1/4” ....1-1/2”
GRCFF2000.....King Nipple ..................2” ..........2-1/4”
GRCFF3000.....King Nipple ..................3” ..........3-1/4”
FFC King Nipple 90° Full Flow
Bronze
Stock #
Description
NPT :
Hose ID:
GRCFFC500.....King Nipple 90° ...........1/2" .......3/4”
GRCFFC750.....King Nipple 90° ...........3/4” .......1”
GRCFFC1000...King Nipple 90°
1"
1-1/4”
GRCFFC1125...King Nipple 90° ...........1" .......... 1-1/8"
GRCFFC1250...King Nipple 90° ...........1-1/4” .... 1-1/2"
GRCFFC1500...King Nipple 90° ...........1-1/2” ..... 1-3/4"
GRCFFC2000...King Nipple 90° ...........2” ........... 2-1/4"
GRCFFC2500...King Nipple 90° ...........2-1/2” .... 2-3/4"
GRCFFC3000...King Nipple 90° ...........3” .......... 3-1/4"
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
329
Strainers
Intake Strainer
Cast bronze construction with machined slots.
Display pack.
Stock #
Scoop Strainers
Cast bronze.
Thru-Hull
Size
Screw
Inches
Inches
Strainer
Size
Pumps & Plumbing
Stock #
Outside
Dimension
Pipe Size
PRK65DP4PLB .....1/2" .........3" x 4"
PRK65DP5PLB .....3/4" .........3" x 4"
PRK65DP6PLB .....1" ............3" x 4"
PRK65DP7PLB .....1 1/4" ......3 1/4" x 4 1/4"
PRK66DP1PLB .....3-1/2 x 2-1/2............1/2 ...........8.
PRK66DP2PLB ....5 x 3 1/4 ..................1..............8
PRK66DP3PLB .....6-1/4 x 4-1/4............1-1/4........8
PRK66DP4PLB ....8 x 5-1/8..................2..............8.
Round Strainer
Bronze.
Stock #
Strainer Scoop
Cast bronze.
Dimensions: Length: 3 3/8" - Height: 2 5/8"- Depth: 3/4".
Stock #
Description
Max T-Hull
Outside Diametert
GRCRSC1000...Strainer Rnd Hingd...1”............3.63"
Description
SDG367487 ...........Scoop Strainer Bronze
Scoop Strainer
Injection molded nylon
Stock #
A
B
C
Fastener
Weight
SDG365483 ...........3-1/4" ......4-3/4" ......7/8" .........#6 FH ......0.6 Lb.
Round Strainer
Cast bronze.
Stock #
APHS Bronze Strainer with Access Door
Perforated hull strainer. Access to thru-hull fitting & seacock
beneath strainer, easy with door design.
• No need to remove entire strainer to clear marine growth.
• Aluminum models may be welded or screwed to aluminum hulls.
Stock #
Description
Max T Hull:
GRCAPHS1250 .....Strainer with Door 1.25" Perforated
GRCAPHS2000 .....Strainer with Door 2” Perforated
1 1/4"
2"
3"
4"
Bilge Strainer.
1-1/4"or 1-1/2". 6-1/4" Long x 2-1/4" Wide x 2-1/2" High
Outside
Dia.
Inside Thru-Hull Screw
Dia.
Size
Size
PRK86DP1PLB .....2-1/2" ......1-5/8" ........1/2"..........8
PRK86DP2 ............3" ............2" ..............3/4"..........8
PRK86DP3PLB ....3-1/2" ......2-3/8"........1" ............8
PRK86DP4PLB ....4" ............3" ..............1-1/4" ......8
PRK86DP5PLB ....5" ............3-3/4" ........2" ............8
PRK86006PLB .....6" ............4-1/2" ........2-1/2" ......10
PRK86007PLB .....8" ............6-1/4" ........3" ............10
Stock #
Description
JAB29290-0000 .....................Strainer 1”
Black Polyethylene Strainer
Stock #
Description
Size:
DIXTSS20 .............Strainer Black Poly 1-1/2"
DIXTSS25 .............Strainer Black Poly 2”
DIXTSS35 .............Strainer Black Poly 3”
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
330
Thru-Hulls
Thru-Hull Connections
Cast bronze - Back side of flange is machined to fit hull & grooved
to retain bedding compound. Neck is threaded to approximately
1/8 inch from flange.
Pumps & Plumbing
Stock#
Pipe
Size
Neck
Length
Flange Strainer
Dia.
# 86
PRK322DP3...........3/8"..........2-1/4" ......1-1/2" ......1
PRK322DP4...........1/2"..........2-1/4" ......1-5/8" ......1
PRK322DP5...........3/4"..........2-1/4" ......2" ............2
PRK322DP6...........1..............2-1/2" ......2-1/4" ......3
PRK322DP7...........1-1/4........3" ............2-7/8" ......4
PRK322DP8...........1-1/2........3-1/4" ......3" ............5
PRK322009PLB ...2..............3-1/2" ......3-1/2" ......5
PRK322010PLB ...2-1/2........3-5/8" ......4-1/2" ......6
PRK322011PLB ....3..............4" ............5" ............7
Wrench for Thru-Hull
Makes installation of standard Groco thru-hull fittings possible
for a single installer.
• Works on 1/2" to 3" thru-hull fittings.
Stock #
Description
GRCTHT530..........Tool/Wrench For Thru-Hull
Extra Long Thru-Hull Connections
Cast Bronze. Same as 322 except neck is threaded to approximately 1 inch from flange.
Stock#
Pipe
Size
Neck
Length
Flange Strainer
Dia.
# 86
Weight
Pounds
PRK348DP5PLB ...3/4 ...........5-1/2........2..............2..............3/4
PRK348DP6PLB ..1..............5-1/2........2-1/4 .......3..............1
PRK348DP7PLB ..1-1/4........5-1/2........2-7/8 .......4..............2
PRK348DP8PLB ..1-1/2........5-1/2........3..............5..............2-1/4
PRK348009PLB ...2..............5-1/2........3-1/2........5..............3
PRK348010PLB ....2-1/2........5-1/2........4-1/2........6..............4
Thru-Hull Connections
Molded white plastic. For use with hose.
Stock#
Hose
Size
Dia.
Flange
Dia.
Flange
PRK301DP4...........1/2"..........1-1/4" ........1-1/2"
PRK301DP4A .......5/8"..........1-1/4" ........1-1/2"
PRK301DP5...........3/4"..........1-1/2" ........2-1/16"
PRK301DP6...........1" ............1-7/8" ........2-1/4"
PRK301DP6A ........1-1/8" ......1-7/8" ........2-1/4"
PRK301DP8...........1-1/2" ......2-1/2" ...... 3"
Stainless Thru-Hull
Stainless steel.
Stock #
Stock#
Hose
Size
Flange
Dia.
Max Hull
Thickness
PRK350004DPP ....5/8 ...........1-5/8 .......1-1/4
PRK350005DPP ....3/4 ...........2..............1-5/8
PRK350006DPP ....1..............2-3/8 .......1-7/8
PRK350006ADPP..1-1/8..........2-3/8 ..........1-7/8
PRK350007DPP ....1-1/4........3..............2
PRK350008DPP ....1-1/2 ........3-1/8 ........2
PRK350009PLB .... 2” ...........2-3/8” ......2”
*Thru-Hull Connections for use with hose are not recommended for use below
waterline per ABYC "Safety Standards for Small Craft" section H-27.3.
Call Toll Free: (800) 426-2783 8-5 M-F
NPS
Stainless Steel Thru Hulls for Hose
Polished 316 stainless steel.
Stock #
Hose Thru-Hull Connections
Plain bronze. Use with hose.*
Back-side of flange is machined to fit hull & grooved to
retain bedding compound.
Description
BUC70TH050 ........Thru Hull 1/2"
BUC70TH075 ........Thru Hull 3/4"
BUC70TH100 ........Thru Hull 1"
BUC70TH125 ........Thru Hull 1-1/4"
BUC70TH150 ........Thru Hull 1-1/2"
Description
NPS
Hose
BUC70THH625 .....Thru Hull 1/2” 5/8”
BUC70THH75 .......Thru Hull 3/4” 3/4”
BUC70THH100 .....Thru Hull 1”
1”
BUC70THH112 .....Thru Hull 1”
1-1/8”
BUC70THH125 .....Thru Hull 1-1/4” 1-1/4”
BUC70THH150 .....Thru Hull 1-1/2” 1-1/2”
Bronze Thru-Hull
Plain bronze.
Stock #
Description
NPS
Material
Plain Bronze
Plain Bronze
Seattle: (206) 285-5010 Fax: (206) 285-7925
331
Scuppers
Pumps & Plumbing
Scupper Valve
Injection molded nylon.
Stock #
A
B
Fastener
SDG520500-1 ........2-3/4" .....1-3/4" .....................#6 FH .....
Scupper Valve
• Injection molded nylon. Display pack.
Stock #
Description
OD
ID
SDG520500-1...Scupper Valve ..2-13/16”...1-7/8”
Weight
.06 lb.
Cockpit Scupper
For use when discharge is below waterline.
• Plain or chrome plated cast bronze.
• Rubber check ball. Deck key. Outlet angle is 45°.
Stock #
Cockpit Scupper - Flush Mount
• Molded white plastic. For use with hose.
• Use when discharge is above waterline.
• Insert blocks large objects without restricting water flow.
Stock #
Description
Hose Size
Hull
ID
Description
HozeSize
OD Grate
Od Flange
PRK142001CHR ... Chrome..................1"........1-13/16"...3-1/4"
PRK142001PLB .... Plain Bronze... .......1"....... 1-13/16"...3-1/4"
PRK142002CHR ... Chrome Plate.........1-1/2"..2-1/4"..... 3-5/8"
OD Flange
PRK285DP.....Scupper.....1-1/2”...1-3/4"...1-1/2”...2-3/4”
Scupper Thru- Hull
Mounting thru transom.
• Molded white plastic. Soft black flapper.
• Nut & mounting hardware included.
• Mount Hole 1-7/8”. Hull thickness 2-1/8".
Stock #
Description
Hose Size Flange OD
PRK323DP......Scupper Thru-Hull...1-1/2”...2-7/8”
Scupper Thru-Hull
• Use with hose not recommended below waterline.
• Plain cast bronze. Recessed flapper.
• Flange machined.to fit hull.
• Grooved to retain bedding compound.
• Mount hole 1-7/8". Hull thickness 1-3/4".
Stock #
Description
Hose Size OD Flange
PRK377B08PLB...Scupper Thru-HullLong...1 1/2"...3 1/8"
Scupper Valve Assembly
• Molded white plastic. Soft black flapper.
• Thru hull & mounting hardware not included.
Stock #
Description
OD Flange
PRK365DP.............Scupper.........2-7/8”
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
332
Bilge Pump Strainers/PVC Valves
Pumps & Plumbing
Strainers for Hose
Pump Strainer
Cast bronze.
Hose
Size
Stock #
Length
Overall
Width
Overall
Weight
PRK709DP.............5/8"...........3-5/8"........1-3/4".......6 Oz.
Rubber Expandable Plug
Stock #
Strainers for Pipe
Pump Strainer
Cast bronze.
Stock #
Description
KLL4801 ................Expandable Rubber Plug 1”
KLL4802 ................Expandable Rubber Plug 1-1/4”
KLL4803 ................Expandable Rubber Plug 1-1/2”
Drain Plug
Injection molded nylon designed with molded-in recess in the base.
This traps the sealant in place, providing a more water-tight seal.
Hose
Size
Length
Overall
Width
Overall
Stock #
Weight
PRK721000PLB ....1-1/4" ......4-3/4" ......2-3/4" ......1-3/4 Lb.
PRK722000PLB ....1-1/4" ......4-1/2" ......2-3/4" ......1-3/8 Lb.
A
B
Fastener
Weight
SDG520010 ...........................1" ............1-1/2" ......#10 FH ....03 Lb.
SDG520021-1 ........................Replacement Plug ...................01 Lb.
SCH 40 PVC Ball Valves
150 PSI Max.
Spears SCH80 PVC Ball Valves
Slip or NPT
235 PSI MAX
Stock #
Stock #
Size
SPR2621005 ..........1/2” FNPT
SPR2621007 ..........3/4” FNPT
SPR2621010 ..........1” FNPT
Call Toll Free: (800) 426-2783 8-5 M-F
Size
SPR2329015 ..........1-1/2”
SPR2329020 ..........2”
Seattle: (206) 285-5010 Fax: (206) 285-7925
333
Camlocks
Camlocks
Aluminum Male
Camlocks
PVC Male
Stock #
Description
Stock #
Description
PTF10AAL.............Camlock Male 1” x FNPT
PTF12AAL.............Camlock Male 1-1/4” x FNPT
PTF15AAL.............Camlock Male 1-1/2” x FNPT
PVC Female
Aluminum Female
Stock #
Description
Stock #
Description
PTF10BPP..............Camlock Fem 1” x MNPT
PTF12BPP..............Camlock Fem 1-1/4” x MNPT
PTF15BPP..............Camlock Fem 1-1/2” x MNPT
PTF20BPP..............Camlock Fem 2” x MNPT
PTF10BAL.............Camlock Fem 1” x MNPT
PTF12BAL.............Camlock Fem 1-1/4” x MNPT
PTF15BAL.............Camlock Fem 1-1/2” x MNPT
PTF20BAL.............Camlock Fem 2” x MNPT
PVC Hose Female
Aluminum Hose Female
Stock #
Description
Stock #
Description
Aluminum Female
PTF10CPP..............Camlock Fem 1” x Hose
PTF12CPP..............Camlock Fem 1/1/4” x Hose
PTF15CPP..............Camlock Fem 1-1/2” x Hose
PVC Female
Stock #
PTF10DPP .............Camlock Fem 1” x FNPT
PTF12DPP .............Camlock Fem 1-1/4” x FNPT
PTF15DPP .............Camlock Fem 1-1/2” x FNPT
PVC Hose Male
Stock #
Description
PTF10EPP ..............Camlock Male 1” x Hose
PTF12EPP ..............Camlock Male 1-1/4” x Hose Pp”
PTF15EPP ..............Camlock Male 1-1/2” x Hose
PVC Male
Stock #
Description
PTF10FPP ..............Camlock Male 1” x MNPT
PTF12FPP ..............Camlock Male 1-1/4” x MNPT ”
PTF15FPP ..............Camlock Male 1-1/2” x MNPT
PTF20FPP ..............Camlock Male 2” x MNPT
PVC Cap
Stock #
Description
PTF10VPP .............Camlock Dust Cap 1”
PTF12VPP .............Camlock Dust Cap 1-1/4”
PTF15VPP .............Camlock Dust Cap 1-1/2”
PTF20VPP .............Camlock Dust Cap 2”
PVC Plug
Stock #
Description
PTF10WPP.............Camlock Dust Plug 1”
PTF12WPP.............Camlock Dust Plug 1-1/4”
PTF15WPP.............Camlock Dust Plug 1-1/2”
PTF20WPP.............Camlock Dust Plug 2”
l
Call Toll Free: (800) 426-2783 8-5 M-F
Pumps & Plumbing
PTF10APP .............Camlock Male 1” x FNPT
PTF12APP .............Camlock Male 1-1/4” x FNPT
PTF15APP .............Camlock Male 1-1/2” x FNPT
Description
PTF10CAL.............Camlock Fem 1” x Hose
PTF12CAL.............Camlock Fem 1-1/4” x Hose
PTF15CAL.............Camlock Fem 1-1/2” x Hose
Stock #
Description
PTF10DAL.............Camlock Fem 1” x FNPT
PTF12DAL.............Camlock Fem 1-1/4” x FNPT
PTF15DAL.............Camlock Fem 1-1/2” x FNPT
Aluminum Hose Male
Stock #
Description
PTF10EAL .............Camlock Male 1” x Hose
PTF12EAL .............Camlock Male 1-1/4” x Hose
PTF15EAL .............Camlock Male 1-1/2” x Hose
Aluminum Male
Stock #
Description
PTF10FAL .............Camlock Male 1” x MNPT
PTF12FAL .............Camlock Male 1-1/4”” x MNPT Al
PTF15FAL .............Camlock Male 1-1/2” x MNPT
PTF20FAL .............Camlock Male 2” x MNPT
Aluminum Cap
Stock #
Description
PTF10VAL .............Camlock Dust Cap 1”
PTF12VAL .............Camlock Dust Cap 1-1/4”
PTF15VAL .............Camlock Dust Cap 1-1/2”
PTF20VAL .............Camlock Dust Cap 2”
Aluminum Plug
Stock #
Description
PTF10WAL ............Camlock Dust Plug 1”
PTF12WAL ............Camlock Dust Plug 1-1/4”
PTF15WAL ............Camlock Dust Plug 1-1/2”
PTF20WAL ............Camlock Dust Plug 2”
l
Seattle: (206) 285-5010 Fax: (206) 285-7925
Pumps & Plumbing
334
Vents
Gas Tank Vents
Chrome plated zinc with removable Monel wire 30 mesh
screening. With Splash Shield
Stock #
Description
Perko Gas Tank Vent
Chrome plated pressure cast bronze.
• Removable brass wire 30 mesh flame arrester.
• 1/2" N.P.T. is off center to create a water baffle.
• Meets reqs. of National Fire Protection Assn. Booklet
#302 Section #323 on vent pipe outlets.
Stock #
Description
PRK505DP.............Vent gas tank, chrome
PRK506DP4CHR ..................Vent Gas Tank
Gas Tank Vent
Stainless steel - Bulk
Gas Tank Vents
Chrome plated pressure cast bronze
with removable Monel wire 30 mesh screening.
Stock #
Stock #
Description
PRK509DP5 ..........................Vent Gas Tank, Chrome
Gas Tank Vent
Injection molded nylon - Bulk.
Stock #
Gas Tank Vents
Chrome plated pressure cast bronze
with removable Monel wire 30 mesh screening.
Stock #
Hose
SDG352210 ...........9/16"
Hose
SDG357100 ...........5/8"
Description
PRK503DP3...........Chrome
90° Tank Vent
Cast 316 stainless steel - Bulk
Stock #
Hose
SDG352230 ...........9/16"
Gas Tank Vents
Chrome plated pressure cast bronze with removable Monel wire 30 mesh screening.
Stock #
Description
Gas Tank Vent
Machined brass chrome plated.
Stock #
Stock #
A
B
C
D
SDG352010-1 ........15/16" ......2-1/4" ......9/16" Hose ..............1-5/16"
Vent for Gas Tank
Die cast zinc, chrome plated.
Dimensions: Stem length: 1" - Hose Dia: 5/8".
Vent: 3/4".
Description
SDG352110-1 ........Vent for Gas Tank Zinc/Chrome DP
Gas Tank Vent
• Chrome plated bronze.
• Removable 30 mesh stainless steel screen flame arrestor.
Stock #
Description
Hose Size
Gas Tank Vent
Machined brass chrome plated.
Stock #
A
B
SDG352020-1 ........1-13/16" ...................3/8" Pipe
Hull Thickness
PRK509DP4...........Vent For Gas Tank....5/8".....3/4"
PRK509DP5...........Vent For Gas Tank....3/4".....5/8"
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
335
Deck Fills
1319 Combo: Gas Fill & Tank Vent
Black plastic.
Integral tank vent with flame arrestor & a flip top cap.
No deck plate key or ground wire required.
Stock #
Stock #
Marking
A
B
SDG351320 ...........Gas .........1-1/2" Hose .............2-3/16"
SDG351321 ...........Diesel .....1-1/2" Hose .............2-3/16"
SDG351322 ...........Water ......1-1/2" Hose .............2-3/16"
SDG351323 ...........Waste ......1-1/2" Hose .............2-3/16"
SDG351330 ...........Gas .........2" Hose ...................2-3/16"
SDG351331 ...........Diesel .....2" Hose ...................2-3/16"
SDG351390-1 ........Replacement Cap for: 351320 - 351323
SDG335699-1 ........Deck Plate Key
Marked
for:
Fuel
Hose
Vent
Hose
Neck
Length
PRK1319DPGBLK ................Gas .........1-1/2" ......5/8" .........2-7/16"
PRK1319DPWBLK ...............Water ......1-1/2" ......5/8" .........2-7/16"
Pumps & Plumbing
Hose Deck Fill
Investment cast 316 stainless.
Models: 351320 - 351323 cap threads are:
1-1/4" - 11-1/2 NPSM Straight
Models: 351330 - 351331 cap threads are:
1-1/2" - 12 NPSM Straight
Hose Deck Fill with Splash Guard
Stamped 304 stainless.
Pipe Deck Fill
Investment cast 316 Stainless.
Models: 351350 - 351353 Cap threads are:
1-1/2" - 12 NPSM Straight
Stock #
Marking
A
Stock #
Marking
B
SDG351350 ...........Gas .........1-1/2" Hose .............1-1/2"
SDG351351 ...........Diesel .....1-1/2" Hose .............1-1/2"
Stainless Steel Deck Fills - Seadog
Stock #
Hose Deck Fill with Splash Guard
Die cast zinc. Chrome plated.
Stock #
Marking
A
A
SDG351250 ...........Gas .........................................1-1/2" Hose
SDG351255-1 ........Replacement Cap (351250, 351251)
B
SDG351750-1 ........Gas .........1-1/2" Hose .............1-5/8"
SDG351755-1 ........Replacement Cap for: 351750
Markings
Fitting
SDG351260 ...........Gas .........................1-1/2" Pipe
SDG351261 ...........Diesel .....................1-1/2" Pipe
SDG351263 ...........Water ......................1-1/2" Pipe
SDG351264 ...........Waste ......................1-1/2" Pipe
SDG351265 ...........Gas .........................1-1/2" Pipe
SDG351269-1 ........Replacement Cap (351260, 1, 3, 4)
SDG351270-1 ........Replacement Cap (351265, 6, 7, 8)
Deck Fill with Splash Guard
SDG351250 ...........Gas .........................1-1/2" Pipe
SDG351255-1 ........Replacement Cap (351250)
No-Spill Fuel Saver
Designed for gas/diesel. Fuel resistant bottle for
temporary attachment to hull over fuel tank vent.
Captures fuel spilled from vent when tank reaches
full level. Fuel could stain hull & run into water.
Saves money, great for environment & fish.
Attaches to hull with 2 strong suction cups.
Fits all tank vents up to 1.5” in diameter.
Stock #
DAV376 .................No-Spill Fuel Saver
Call Toll Free: (800) 426-2783 8-5 M-F
Locking Gas Fill
• Chrome plated zinc alloy. Black plastic flange.
• Black plastic cap with strap.
• Cap retainer & gasket - grounding screw.
• Locking cap has cover for key hole.
Stock #
Description
HozeSize
OD Neck Od Flange Hole
PRK1399DP...Fill Lock Gas..1-1/2"...1-7/8"...3-1/8"....2-1/8"
Seattle: (206) 285-5010 Fax: (206) 285-7925
Pumps & Plumbing
336
Deck Fills
Deck Fill with Keyless Cap
Built of injection molded fiberglass
filled nylon & do not require
grounding to boat electrical system like
deck fills using metal.
Each deck fill has a special cap with
built-in key for easy cap removal.
Hinged key locks in upright position to
open/close fill & then recessed for flush surface.
Special color caps prevent dangerous and costly mix-ups from placing
fuel in water or waste tanks or vice-versa.
Cap threads are 1-1/4" - 11-1/2 NPSM.
White Body
Stock #
Marking
Cap Color
A
B
Marking
Cap Color
A
B
SDG357023-1 ........Water ......Blue ........1-1/2" Hose ............1-9/16"
Black Body
Special Order
Stock #
SDG357033 ...........Water ......Blue ........1-1/2" Hose .............1-9/16"
Replacement Caps
SDG357090-1 ........Gas .........Replacement Cap - Red
SDG357091-1 ........Diesel .....Replacement Cap - Green
SDG357093-1 ........Water ......Replacement Cap - Blue
SDG357094-1 ........Waste ......Replacement Cap - Brown
Perko Deck Plates For Pipe
Cast bronze or chrome plated bronze
construction. Complete with #1248 key
& O-ring.
1 1/4" & 1 1/2" caps have a slot between the
holes. Unmarked:
Stock #
Pipe Size
O.D. Flange Finish
Pipe Size
O.D. Flange Finish
Pipe Size
O.D. Flange Finish
Stock #
Pipe Size
O.D. Flange Finish
Pipe
Plain
Size
Bronze Cap*
PRK528006PLB ....1" ............2-7/8" ......Bronze
PRK528007PLB ....1-1/4" ......3-5/16" ....Bronze
PRK528008PLB ....1-1/2" ......3-5/8" ......Bronze
PRK528009PLB ....2" ............4-1/4" ......Bronze
PRK528010PLB ....2-1/2" ......4-5/8" ......Bronze
PRK528011PLB.....3" ............5-3/8" ......Bronze
PRK528006CHR ...1" ............2-7/8" ......Chrome
PRK528007CHR ...1-1/4" ......3-5/16" ....Chrome
PRK528009CHR ...2" ............4-1/4" ......Chrome
Marked "Gas".
Stock #
PRK528G08CHR...1-1/2" ......3-5/8" ......Chrome
PRK528G09CHR...2" ............4-1/4" ......Chrome
Marked "Diesel".
Stock #
PRK528D08PLB ...1-1/2" ......3-5/8" ......Bronze
PRK528D09PLB ...2" ............4-1/4" ......Bronze
PRK528D09CHR...2" ............4-1/4" ......Chrome
Deck Fill
• Injection molded fiberglass nylon.
• Caps have attachment chain - Display pack.
Stock #
Marked
Marked "Water".
PRK528W08PLB...1-1/2" ......3-5/8" ......Bronze
Spare Parts - Order Info.
Hose
SDG357010-1 ........Gas .........1 1/2"
SDG357011-1 ........Diesel .....1 1/2"
Chromalex Fills
• Chrome plated zinc. Marked for Gas.
• Black plastic flange & cap.
• Complete with key, O-ring & integral retainer on cap.
Stock#
Hose
Flange
Neck
Chrome-Plated
Bronze Cap*
O-rings Only
(2 per bag)
1" ............................PRK528P0699A.....................................
1-1/4" ......................PRK528P0799A.....PRK528C0799A ....PRK513007
1-1/2" ......................PRK528P0899A.....................................PRK513008
2..............................PRK528P0999A.....PRK528C0999A ....PRK513009
2-1/2" ......................PRK528P1099A.....................................PRK513010
3" ............................PRK528P1199A .....................................PRK513011
*Complete with 0-ring.
Screw
PRK1313DP...........................1-1/2" ......3-1/2" ......2-1/2" ......6
Spare Parts:
Stock #
Description
PRK126DP.............................Spare Non-Locking Cap
PRK1324DP...........................Spare Locking Cap
Deck Fill with Slotted CAP
All caps include attachment chains.
• Black body color
• Water cap marking. Blue cap color.
1-1/2” hose, 6- 7/8" overall.
Stock #
Description
SDG357013-1 ........Deck Fill 1.5” Blue Water DP
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
337
Deck Plates
Waste Deck Plate For Pipe
Chrome plated bronze.
Complete with 1248 key & O-ring.
Cap has a slot between the holes.
Pipe
Size
O.D.
Flange
Stock #
Description
Screw
Stock#
Size
PRK524DP.............1-1/2" ......3-5/8" ......................8
Stock #
Inches
Inches
Length
Neck
Inches
Length
Neck
Screw
Size
Description
PRK124878DP.......Spare Key
PRK513008 ............Spare O-rings only (2 per bag).
Waste Deck Plate For Hose
• Chrome plated zinc.
• Black plastic cap.
• Complete with key & O-ring.
• Cap has a slot between holes.
O.D.
Flange
O.D.
Flange
PRK520DPDCHR .1-1/2" ......3-1/8" ......3-1/2" ......8
PRK524DP99A ......Spare Cap with O-ring
PRK513008 ............Spare O-rings only (2 per/bag).
Pipe
Size
Hose
Size
Pumps & Plumbing
1 Pc. per card
Deck Plates For Hose
Chrome plated bronze. Marked for diesel.
• Complete with: #1248 key, O-ring. Integral retainer on Cap.
• Caps have a slot between the holes.
Deck Plates For Hose
Chrome plated zinc. Black plastic cap.
• Complete with: #1248 key, O-ring. Integral retainer on Cap.
• Caps have a slot between the holes.
Display Pkg. -5 pcs
1 Pc. per card
Screw
Stock#
Size
Hose
Size
O.D.
Flange
Length
Neck
Screw
Size
1-1/2........3-1/2........2-1/2........PRK1269DP........... 8
PRK1270DPW .......1-1/2" ......3-1/2" ......2-1/2" ......8
Stock #
Stock #
Description
Description
Deck Plate
• Chrome. 1-1/2" fills for hose
• Base length 1-1/4" x 3/4". Hole size: 5/16".
Stock #
Regular Deck Plate
• Cast bronze.
• Plain standard.
• Complete with key.
Stock#
I.D.
Opening
Description
PRK1270DPG ........................Deck Fill Gas
PRK1270DPDCHR ...............Deck Fill Diesel
PRK1270DPW .......................Deck Fill Water
O.D.
Overall
Screw
Size
Weight
PRK526003PLB ....3..............5-3/8........................10............2
Lb.
PRK526004PLB ....4..............7-1/16 ......................10............3-3/8 Lb.
PRK526005PLB ....5..............8-3/8........................10............4-3/4 Lb.
PRK526006PLB ....6..............9-3/8........................1/4 ..........7-1/2 Lb.
Gas Fill
• Chrome plated zinc alloy.
Black plastic flange.
• Black plastic cap with strap.
• Cap retainer & gasket. Grounding screw.
Stock #
Description
HozeSize
OD Neck Od Flange Hole
PRK1313DP...Fill Gas Chrome..1-1/2"...1-7/8"...3-1/8"....2-1/8"
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
338
Deck Plates / Fills
Deck Fill
• Aluminum, with key and plastic cap. 1.75 filler opening.
Pumps & Plumbing
Stock #
Description
BAYB-02 ...............Aluminum Fill
Sink Drain
Injection Molded Delrin
Stock #
Style
A
SDG517310 ...........Drain Straight .........1"
SDG517315 ...........Sink Drain 90 Deg 1” Hose
Universal Deck Plate Key
Fits all deck plate caps. Stainless steel will not corrode.
Stock #
Description
DAV381 .................Universal Deck Plate Key
Deck Fill - Display Pack
Investment cast brass 316 stainless steel.
Dimensions: Length: 1-3/16".
Stock #
Description
SDG351399-1 ........Deck Fill Key SS DP
Deck Plate Key
Keys for 1" thru 1-1/2" deck plates have a 1"
spade on handle allows fitting many other "slot"
type opening deck plates.
Deck
Plate Size
Stock #
C. to C.
Of Lugs
PRK124878DP.......................1-1/4" - 1-1/2" .........1-1/8"
PRK1248009ZNC ..................2" ............................1-11/16"
PRK1248010ZNC ..................2-1/2" ......................2"
Retaining Deck Plate Key
• Chrome plated zinc.
• Compact size with a hole for a key chain.
• Fits Perko 1-1/4" & 1-1/2" deck plates.
• Fits many other "slot" type deck plates.
Stock #
Deck Plate Key
• Formed 304 stainless - 7" length
Stock #
PRK1247DP...........Deck Plate Key
Description
SDG335699 ...........Key For Deck Plate
SDG335699-1 ........Key For Deck Plate, DP
Universal Deck Plate Fill Key
Ultimate deck plate key fits all
Sea-Dog fuel fills, & most others on market.
A very handy tool for any toolbox
Screwdriver, shackle key, bottle-opener.
Stock #
Description
Perko Deck Plate Key
Chrome plated zinc.
Heavy duty. Will fit sizes up to 8" diameter.
Stock #
Overall Length
PRK826DP.............8-1/2"
SDG335690-1 ........Deck Key
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
339
Shields Hose
Stock #
Shields VAC Hose Extra Heavy Duty Industrial Grade
Multi-purpose, extra-heavy smooth-walled, all vinyl hose.
Uses: critical bilge, drain, scupper & air conditioner circulation lines.
• Available: large sizes for high capacity pumps.
• Good economy grade sanitation hose for head intake, holding
tank vent, holding tank discharge, 1/2 toilet discharge.
• Clear vinyl reinforced with white rigid helix.
• See-through to allow visual check for blockage.
• Good bend radius, vacuum rating & corrosion protection.
• Smooth cover permits clamping without cuffs.
• Recommended double clamps & sealing compound for below
waterline connection.
Stock #
I.D.
Bend
Radius
Vac
Rating
Wt. "C"
SHD146-0340 ........3/4" .........3..............28............20
SHD146-0580 ........5/8 ..........3..............28............15
SHD146-1000 ........1" ............3..............28............27
SHD146-1140 ........1-1/4" ......3..............28............30
SHD146-1120 ........1-1/2" ......4..............28............40
SHD146-1180 ........1-1/8" .....4..............28............25
SHD146-2000 ........2" ............5..............28............57
SHD146-2120 ........2-1/2" ......7..............28............74
SHD146-3000 ........3" ............9..............28............94
Shields 400/402 Vinylvent Vent Hose
Venting of bilge gases & fumes.
• PVC hose supported by helical wire.
• Resistant to ozone, sunlight and weathering.
• Will not support a flame.
Stock #
I.D.
O.D.
Wt/C
I.D.
Wall
Pressure
70°F
Wt/C
SHD150-0366 ........3/16".........062.........65#..........3
SHD150-0146 ........1/4" ..........078.........60#..........4
SHD150-0566 ........5/16".........093.........55#..........5
SHD150-0386 ........3/8" ..........094.........55#..........6
SHD150-0126 ........1/2" ..........110 .........45#..........12
SHD150-0586 ........5/8" ..........110 .........40#..........15
SHD150-0346 ........3/4" ..........110 .........35#..........19
SHD150-1006 ........1" .............125.........20#..........27
SHD150-1146 ........1-1/4" .......125.........20#..........31
SHD150-1126 ........1-1/2" .......125.........20#..........34
Pumps & Plumbing
PVC Tubing Clear Hose
Single layer vinyl, non toxic, made of FDA approved compound.
Uses: sink, shower, cooler, refrigerator & livewell drain lines.
• Supply line for non-pressurized water system.
• Not recommended for hot water.
All Clear PVC Tubing Polyester Reinforced (Red Tracer)
• Heavy duty: hot/cold pressurized water systems.
(burst pressure 250#). Vent & drain lines, bilge pump discharge.
• Heavy walled FDA approved vinyl compound, non-toxic,
tasteless, odorless. Polyester braid reinforcement.
• Temp range: 25°F - 150°F
Stock #
I.D.
O.D.
Burst
Pressure
Wt/C
SHD162-0386 ........3/8" .........9/16"........250#........7
SHD162-0126 ........1/2" ..........23/32" ......250#........11
SHD162-0586 ........5/8" .........27/32" ......250#........14
SHD162-0346 ........3/4" .........31/32" ......250#........17
SHD162-1006 ........1" ............1-5/16" ....250#........24
SHD162-1146 ........1-1/4" ......1-5/8" ......250#........44
SHD162-1126 ........1-1/2" ......1-15/16" ..250#........67
Reinforced Vinyl Hose
Non-collapsing wire reinforced vinyl hose.
Stock #
Color
Description
BOS044 ..Hose Wire Reinforced 1” ID
SHD400-3000 ........3" ............3 1/8" ......8..............White
SHD400-4000 ........4" ............4 1/8" ......10............White
SHD402-3000B .....3" ............3 1/8" ......8..............Black
SHD402-4000 ........4" ............4 1/8" ......10............Black
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
Pumps & Plumbing
340
Hose
Shields VAC Extra Heavy Duty FDA Hose
For sanitation system connections.
• Multi-purpose, extra-heavy smooth walled, all vinyl hose.
• Use for head intake, head to holding tank, holding tank discharge & pump out.
• Critical bilge, drain, scupper line, & potable water fill uses.
• Specially formulated with FDA approved & low water absorption compounds
gives excellent resistance to odor permeation & toilet chemicals.
• Reinforced with hard vinyl helix for good bend radius,
vacuum rating/corrosion protection.
• Smooth cover permits clamping without cuffs. Temp range: -13° to +158°F.
Recommended for below water line use.
Stock #
I.D.
Bend
Radius
Vac
Rating
Wt. "C"
Stock #
SHD148-0586 ........5/8" .........3..............28............15
SHD148-0346 ........3/4" .........3..............28............19
SHD148-1006 ........1" ............3..............28............24
SHD148-1186 ........1-1/8" ......4..............28............28
SHD148-1146 ........1-1/4" ......4..............28............30
SHD148-1126 ........1-1/2" .....5..............28............39
I.D.
O.D.
Spiral
Burst Pres.
Wt. "C"
SHD130-0126 ........1/2" .........25/32" ........2............450#..........18
SHD130-0586 ........5/8" ..........15/16" ........4............450#..........20
SHD130-0346 ........3/4" .........1 3/32" .......4............450#..........24
Blue Water Suction Hose
Use for sink, icebox, shower, baitbox drainline, engine water, bilge pump
& air conditioner circulation.
• Resistant to mild chemicals, heat, cold, ozone, & saltwater.
• Clear with blue spiral reinforcement.
• Very flexible for a heavy duty suction hose.
Stock #
Description
PRBBW34 .............3/4” PCV Blue Water Hose
PRBBW1 ...............1” PVC Blue Water Hose
PRBBW114 ............1-1/4” PCV Blue Water Hose
PRBBW112 ............1-1/2” PVC Blue Water Hose
PRBBW2 ...............2” PCV Blue Water Hose
Description
SHD168-0146 ........Tubing PVC Reinforced 1/4” FDA
Shields # 1300 H.D. Water Heater Hose
Use for sink, icebox, shower, baitbox drainline, engine water, bilge pump
& air conditioner circulation.
• Resistant to: mild chemicals, heat, cold, ozone, & saltwater.
• Temp range: -40° to -210°F.
Stock #
Heavy-Duty Polyester Reinforced PVC Tubing
Extra heavy-duty for hot or cold pressurized water systems,
where superior kink resistance is desired.
• Extra wall thickness increases kink resistance.
• FDA approved virgin vinyl/compound. Non-toxic.
• Polyester bias assures high burst pressure.
Bellowsflex Hose
Flexible, wire reinforced hose with a continuous yellow stripe.
Meets USCG for specification SAEJI527 Type B2 hose as a fuel
fill hose. Temp. range -20 to 212 F. All sizes shown are I.D.
Stock #
Description
BRP79100500 ........Hose Bellowsflex 1/2” Yellow
BRP79101000 ........Hose Bellowsflex 1” Yellow
BRP79101125 ........Hose Bellowsflex 1-1/8” Yellow
/
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
341
Hose
Marine Water / Exhaust Hose (w/wire)
Stock #
I.D.
Length
SHD250-0124 ........1/2”...............12.5 Ft.
SHD250-0344 ........3/4”...............12.5 Ft.
SHD250-0584 ........5/8”...............12.5 Ft.
SHD250-0784 ........7/8”...............12.5 Ft.
Pumps & Plumbing
Flex II Marine Water/Exhaust Hose with Wire
Premium reinforced marine hose. Shieldsflex II is used in marine
water & wet-exhaust uses.
Designed for engine intake, bilge discharge, toilet/holding tank connections,
scupper line. Marine wet-exhaust connections requiring a
long-length (greater than 4 times inside diameter) or if connection
needs big bend.
• Reinforced with wire helix imbedded between
tough synthetic spiral cord plies.
• Excellent flexibility & bend radius, prevents
panting/collapsing & provides excellent service life.
• Resists: engine heat, exhaust fumes, ozone, mild acids, toilet
effluent, salt water & abrasion.
• Meets/exceeds standards for: Type certified wet exhaust hose.
• Recommended double clamp & sealing compound for below water
line connection.
• Color coded: Blue & Green stripe marked continuously with size
& part number.
SHD250-1000 ........1”..................50 Ft.
SHD250-1004 ........1"..................12.5 Ft.
SHD250-1120 ........1-1/2"........... 50 Ft.
SHD250-1124 ........1-1/2”........... 12.5 Ft.
SHD250-1140 ........1-1/4”........... 50 Ft.
SHD250-1144 ........1-1/4"........... 12.5 Ft.
SHD250-1180 ........1-1/8”........... 50 Ft.
SHD250-1184 ........1-1/8"........... 12.5 Ft.
SHD250-1344 ........1-3/4"........... 12.5 Ft.
SHD250-1380 ........1-3/8”........... 50 Ft.
SHD250-1384 ........1-3/8"........... 12.5 Ft.
SHD250-1580 ........5/8”.............. 50 Ft.
SHD250-1584 ........1-5/8”........... 12.5 Ft.
SHD250-1780 ........1-7/8"........... 50 Ft.
SHD250-1784 ........1-7/8”........... 12.5 Ft.
SHD250-2004 ........2"..................12.5 Ft.
SHD250-2124 ........2-1/2"........... 12.5 Ft.
SHD250-2140 ........2-1/4”........... 50 Ft.
SHD250-2144 ........2-1/4"........... 12.5 Ft.
SHD250-2184 ........2-1/8"........... 12.5 Ft.
SHD250-2344 ........2-3/4"........... 12.5 Ft.
SHD250-2384 ........2-3/8"........... 12.5 Ft.
SHD250-2584 ........2-5/8"........... 12.5 Ft.
SHD250-2784 .......2-7/8"........... 12.5 Ft.
SHD250-3000 ........3”..................50 Ft.
SHD250-3004 ........3" ..................12.5 Ft.
SHD250-3124 ........3-1/2"........... 12.5 Ft.
SHD250-4004 ........4" ..................12.5 Ft.
SHD250-6001 ........6”..................6.25 Ft.
"Buckeye" Wet Exhaust Hose 2 Ply Hose
2 ply soft wall hose. No wire.
• For straight connection in wet exhaust systems on marine
gasoline/diesel engines.
• Marine drains, replacement of metal piping & vibration absorption.
• Continuous blue stripe.
• Tube blended for coolant & heat resistance.
• Temperature Range 0 to 212 degrees F.
Sizes: 3/4" to 1-7/8" rated at 150 PSI
2" to 5" rated at 100 PSI
Sizes: 5-1/2" to 12" available by special order only.
Call Toll Free: (800) 426-2783 8-5 M-F
Stock#
I.D.
O.D.
BRP24001250 ........1-1/4" ......1.95"
BRP24001375 ........1-3/8" ......2.08"
BRP24001500 ........1-1/2" ......2.20"
BRP24001625 ........1-5/8" .....2.32"
BRP24001750 ........1-3/4" .....2.45"
BRP24001875 ........1-7/8" ......2.57"
BRP24002000 ........2" ............2.70"
BRP24002125 ........2-1/8" .....2.82"
BRP24002250 ........2-1/4" ......2.95"
BRP24002375 ........2-3/8" ......3.07"
BRP24002500 ........2-1/2" ......3.20"
BRP24002625 ........2-5/8" ......3.33"
Stock#
I.D.
O.D.
BRP24002750......2-3/4".....3.43"
BRP24002875......2-7/8" 3.57"
BRP24003000......3"...........3.70"
BRP24003250......3-1/4".....3.95"
BRP24003500......3-1/2".... 4.20"
BRP24003750......3-3/4".....4.45"
BRP24004000......4"...........4.70"
BRP24004500......4-1/2".....5.20"
BRP24285000......5"...........5.70"
Seattle: (206) 285-5010 Fax: (206) 285-7925
342
Hose
Pumps & Plumbing
Shields 315 Fuel Feed & Vent Hose
Premium quality marine fuel hose, designed to handle today's
alcohol-enhanced gasolines.
• Use where fire retardant hose is Not required.
• Excellent for diesel fuel.
• Permeation is less than 300g/m²/24 hours.
• Reinforced with 2 spirals of high-strength polyester fabric.
• Shields 315 meets/exceeds reqs: SAE J1527 Type B2.
Stock #
I.D.
O.D.
Ply
Burst
Pressure
Wt. "C"
SHD315-0146 ........1/4" .........17/32" ......2..............175#........9.2
SHD315-0566 ........5/16"........19/32" ......2..............175#........10.8
SHD315-0386 ........3/8" .........21/32" ......2..............175#........10.8
SHD315-0586 ........5/8" .........29/32" ......2..............175#........24.0
Shields Fire-Acol Fuel Feed, Vent & Fill Hose
Premium quality fire retardant marine fuel hose handles alcohol enhanced gasolines.
• High nitrile tube resists permeation of alcohol enhanced fuels.
• Reinforced with 2 spirals of high-strength synthetic fabric provides excellent bend radius.
• Fill hose sizes have helical wire imbedded between fabric plies:
for superior kink resistance/durability.
Fire-acol approved: USCG & NMMA for all pleasure boat fuel systems.
• Fire-acol Fuel Feed hoses: 1/4" I.D - 1/2" I.D. Complies with SAE J1527 Type A1.
• Fire-acol Fuel Vent & Fill hoses: 1-5/8" I.D - 2 3/8" I.D. Complies with SAE J1527 Type A2.
Type 1 Fuel Feed Hose
Stock #
Description
SHD368-0140 ........Hose Fuel 1/4” Fire-Acol 250 Spl
SHD368-0146 ........Hose Fuel 1/4” Fire-Acol 50' Box
Type 2 Vent/Fill Hose
Stock #
I.D.
Burst
O.D.
Ply
Pressure
Wt. "C"
SHD350-1580 ........1-5/8" .....2-3/64" ...2..............90#..........89
SHD350-1784 ........1-7/8" .....2-9/32" ...2..............90#..........114
SHD350-2004 ........2" ............2-31/64" .2..............90#..........121
SHD350-2384 ........2-3/8" .....2-27/32" .2..............90#..........137
SHD355-1124 ........1-1/2 .......Type A Fuel Fill Hose
Red Horizon Multi-Purpose Hose
High quality multi-purpose rubber hose with
EPDM liner.
Stock #
Description
Size:
PRBGDYR1...........Hose Red Horizon 1”
PRBGDYR1/2 .......Hose Red Horizon 1/2”
PRBGDYR1-1/2 ....Hose Red Horizon 1-1/2”
PRBGDYR1-1/4 ....Hose Red Horizon 1-1/4”
PRBGDYR2...........Hose Red Horizon 2”
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
343
Fittings
1-1/8" Hose Fittings
Stock #
Description
MNE7040W ...........Thru-Hull L-Head 3/4"
MNE7240W ...........Thru-Hull L-Head 1"
MNE6440W ...........Thru-Hull L-Head 1-1/8"
Elbow
Molded of rugged nylon, fits marine sanitation hose.
Stock #
Description
Hose ID Barb
Male
MNE8090...Elbow 100D EL........1-1/8 "x 1-1/2"
Bulkhead Connector
• Designed to reduce hose & cable chafing.
• Ideal for hose cable or wires. • Black.
Stock#
Description
Size:
MNE7920...............Bulkhead Connector 1-1/4” Long
MNE7940...............Bulkhead Connector 1-1/8” Long
MNE7950...............Bulkhead Connector 1-1/8” Short
MNE7960...............Bulkhead Connector 1” Long
MNE7980...............Bulkhead Connector 3/4” Long
MNE7990...............Bulkhead Connector 5/8” Long
Pumps & Plumbing
L- Head Thru Hull
The L-Head allows total compartment drainage.
• Barbed for easy marine hose fitting.
• Available in white. (Black by special order).
• Available in 2 thread lengths 2" & 3".
Hose Adaptor
Molded of high strength engineered plastic.
Stock #
Description
MNE8815...............Adapter Hose x Hose 1-1/8" x 5/8
MNE8840...............Adapter Hose x Hose 1-1/8" x 3/4
MNE8860...............Adapter Hose x Hose 1-1/8" x 1”
MNE8875...............Adapter Hose x Hose 1-1/8" x 1-1/8"
MNE8880...............Adapter Hose x Hose 1-1/8" x 1-1/4
MNE8885...............Adapter Hose x Hose 1-1/8" x 1-1/2
MPT to Barb Hose Adaptors
• Fits marine sanitation hose.
• Molded of high strength engineered plastic.
Stock #
Description
Size:
MNE8903...............King Nipple 1-1/8” x 1/2” MNPT
MNE8913...............King Nipple 1-1/8” x 3/4” MNPT
MNE8923...............King Nipple 1-1/8” x 1” MNPT
MNE8933...............King Nipple 1-1/8” x 1-1/4” MNPT
MNE8943...............King Nipple 1-1/8” x 1-1/2” MNPT
3 Way Fittings for Bilge Hose
Rule offers these convenient Y & T fittings
for bilge hoses.
Stock #
Description
RUL213.......Hose Fitting Y 1-1/8”
RUL216.......Hose Fitting T 1-1/8”
Shields Bilge Flex Bilge Hose
Discharge of electric bilge pumps & hand pumps.
Sizes to fit most major brand pumps.
• Single layer corrugated polyethelene.
• Resists oily acids & sea water.
Color: Black or white. Has clamping cuff every foot.
Stock #
Description
SHD120-0346 ........Hose Bilge 3/4” White
SHD120-0586 ........Hose Bilge 5/8” White
SHD120-1126 ........Hose Bilge 1-1/2” White
SHD120-1146 ........Hose Bilge 1-1/4” White
SHD120B1186 .......Hose Bilge 1-1/8” Black
SHD120W1186 ......Hose Bilge 1-1/8” White
Call Toll Free: (800) 426-2783 8-5 M-F
Seattle: (206) 285-5010 Fax: (206) 285-7925
344
Pipe
Bronze Fittings
Bronze Bushings
Pumps & Plumbing
Stock #
MID44-500
MID44-502
MID44-503
MID44-504
MID44-505
MID44-507
MID44-508
MID44-509
MID44-510
MID44-513
MID44-514
MID44-517
MID44-518
MID44-519
MID44-522
MID44-523
MID44-524
MID44-531
Size: NPT
........... 1/4" x 1/8"
........... 3/8" x 1/4"
........... 1/2" x 1/8"
........... 1/2" x 1/4"
........... 1/2" x 3/8"
........... 3/4" x 1/4"
........... 3/4" x 3/8"
........... 3/4" x 1/2"
........... 1" x 1/4"
........... 1" x 3/4"
...........1-1/4" x 1/4"
...........1-1/4" x 3/4"
...........1-1/4" x 1"
...........1-1/2" x 1/4"
...........1-1/2" x 3/4"
...........1-1/2" x 1"
...........1-1/2" x 1-1/4"
...........2" x 1 1/2"
Bushings
Bronze Caps
Stock #
MID44-471
MID44-472
MID44-473
MID44-474
MID44-475
MID44-476
MID44-477
MID44-478
Size:
...........1/4"
...........3/8"
...........1/2"
...........3/4"
...........1"
...........1-1/4"
...........1-1/2"
...........2"
Caps
Bronze Street Ells 90°
Stock #
Size:
MID44-161 ...........1/4"
MID44-162 ...........3/8"
MID44-163 ...........1/2"
MID44-164 ...........3/4"
MID44-165 ...........1"
MID44-166 ...........1-1/4"
MID44-167 ............1-1/2"
MID44-168 ...........2"
90° Street Elbow
Bronze Plugs
Stock #
MID44-650
MID44-651
MID44-652
MID44-653
MID44-654
MID44-655
MID44-656
MID44-657
MID44-658
Size:
...........1/8"
...........1/4"
...........3/8"
...........1/2"
...........3/4"
...........1"
...........1-1/4"
...........1-1/2"
...........2"
Call Toll Free: (800) 426-2783 8-5 M-F
Plug
Seattle: (206) 285-5010 Fax: (206) 285-7925
345
Pipe
Black Iron SCH40 Fittings
Elbow 90°
MID65-101
MID65-102
MID65-103
MID65-104
MID65-105
MID65-106
MID65-107
MID65-108
...........1/4"
...........3/8"
...........1/2"
...........3/4"
...........1"
...........1-1/4"
...........1-1/2"
...........2"
90° Street Elbow
MID65-161 ...........1/4"
MID65-162 ...........3/8"
MID65-163 ...........1/2"
MID65-164 ...........3/4"
MID65-165 ...........1"
MID65-166 ...........1-1/4
MID65-167 ...........1-1/2"
MID65-168 ...........2"
45° Elbow
MID65-181
MID65-182
MID65-183
MID65-184
MID65-185
MID65-186
MID65-187
MID65-188
...........1/4"
...........3/8"
...........1/2"
...........3/4"
...........1"
...........1-1/4"
...........1-1/2"
...........2"
Pipe Tee
MID65-251 ...........1/4"
MID65-252 ...........3/8"
MID65-253 ...........1/2"
MID65-254 ...........3/4"
MID65-255 ...........1"
MID65-256 ...........1-1/4"
MID65-257 ...........1-1/2"
MID65-258 ............2"
Plugs
MID67-653
MID67-671
MID67-672
MID67-774
MID65-655
MID65-656
MID65-657
MID65-658
Bell Reducers
MID65-432 ...........3/8" x 1/4"
MID65-435 ...........1/2" x 3/8"
MID65-438 ...........3/4" x 1/2"
MID65-442 ...........1" x 3/4"
MID65-446 ...........1-1/4" x 1"
MID65-450 ...........1-1/4" x 1-1/2"
MID65-454 ...........2-1/2" x 1-1/2"
MID65-461 ...........2" x 1-1/2"
King Nipples
MID973-850 .........1/2"
MID973-851 .........3/4"
MID973-852 .........1"
MID973-853 .........1-1/4"
MID973-854 .........1-1/2"
MID973-855 .........2"
Caps
MID65-472 ............3/8"
MID65-473 ...........1/2"
MID65-474 ...........3/4"
MID65-475 ...........1"
MID65-476 ...........1-1/4"
MID65-477 ...........1-1/2"
MID65-478 ...........2"
Bushings
MID65-504
MID65-507
MID65-510
MID65-513
MID65-514
MID67-509
MID65-517
MID65-518
MID65-523
MID65-524
MID65-531
...........1/2 x 1/4"
...........3/4 x 1/4"
...........1 x 1/4"
...........1 x 3/4"
...........1-1/4" x 1-1/4"
........... 3/4" x 1/2"
...........1-1/4" x 3/4"
...........1-1/4" x 1"
...........1-1/2" x 1"
...........1-1/2" x 1-1/4"
...........2"
x 1-1/2"
...........1/2"
...........1/4"
...........3/8"
...........3/4"
...........1"
...........1-1/4"
...........1-1/2"
...........2"
Pumps & Plumbing
Couplings
MID65-411.............1/4"
MID65-412 ...........3/8"
MID65-413 ...........1/2"
MID65-414 ...........3/4"
MID65-415 ...........1"
MID65-416 ...........1-1/4"
MID65-417 ...........1-1/2"
MID65-418 ...........2"
Pipe Nipples
MID57-020 ...........1/4" x CLOSE
MID57-022 ...........1/4" x 2"
MID57-040 ...........3/8" CLOSE
MID57-042 ...........3/8" x 2"
MID57-044 ...........3/8" x 3"
MID57-060 ...........1/2" CLOSE
MID57-062 ...........1/2" x 2"
MID57-064 ...........1/2" x 3"
MID57-080 ...........3/4" CLOSE
MID57-084 ...........3/4" x 3"
MID57-100 ...........1" CLOSE
MID57-103 ...........1" x 3"
MID57-120 ...........1-1/4" CLOSE
MID57-123 ...........1-1/4" x 3
MID57-125 ...........1-1/4" x 4"
MID57-140 ...........1-1/2" CLOSE
MID57-143 ...........1-1/2" x 3"
MID57-160 ...........2" CLOSE
MID57-164 ...........2" x 4"
Brass Fittings
90 Degree Brass Elbows
MID44-101 ............1/4"
MID44-102 ............3/8"
MID44-103 ............1/2"
MID44-104 ............3/4"
MID44-105 ............1"
MID44-106 ............1-1/4"
MID44-107 ............1-1/2"
MID44-108 ............2"
Call Toll Free: (800) 426-2783 8-5 M-F
90° Elbow
Seattle: (206) 285-5010 Fax: (206) 285-7925
346
Fittings
Pumps & Plumbing
PVC SCH40 Fittings
PVC Elbow 90°
SPR408005 ...........1/2"
SPR408007 ...........3/4"
SPR408010 ...........1"
SPR408012 ...........1-1/4"
SPR408015 ...........1-1/2"
SPR408020 ...........2"
King Nipple
SPR1436005 .........1/2"
SPR1436007 .........3/4"
SPR1436010 ..........1"
SPR1436012 ..........1-1/4"
SPR1436015 ..........1-1/2"
SPR1436020 ..........2"
Street Ell 90°
SPR412005 ...........1/2"
SPR412007 ...........3/4"
SPR412010 ...........1"
SPR412012 ...........1-1/4
SPR412015 ...........1-1/2
SPR412020 ...........2"
Nipples PVC SCH 80
SPR880005 ...........1/4" CLOSE
SPR880015 ...........1/4" x 1-1/2"
SPR880020 ...........1/4" x 2"
SPR880030 ...........1/4" x 3"
SPR880060 ...........1/4" x 6"
Nipples PVC SCH 80
SPR881005 ...........3/8" x CLOSE
SPR881015 ...........3/8" x 1-1/2"
SPR881020 ...........3/8" x 2"
SPR881030 ...........3/8" x 3"
SPR881040 ...........3/8" x 4"
SPR881060 ...........3/8" x 6"
Nipples PVC SCH 80
SPR882005 ...........1/2" x CLOSE
SPR882020 ...........1/2" x 2"
SPR882030 ...........1/2" x 3"
SPR882040 ...........1/2" x 4"
SPR882050 ...........1/2" x 5"
SPR882060 ...........1/2" x 6"
Nipples PVC SCH 80
SPR883005 ...........3/4" CLOSE
SPR883015 ...........3/4" x 1 1/2"
SPR883020 ...........3/4" x 2"
SPR883030 ...........3/4" x 3"
SPR883040 ...........3/4" x 4"
SPR883050 ...........3/4" x 5"
SPR883060 ...........3/4" x 6"
Call Toll Free: (800) 426-2783 8-5 M-F
PVC Bushings
SPR439052 ............3/8" x 1/4"
SPR439073 ............1/2" x 3/8"
SPR439101 ...........3/4" x 1/2"
SPR439131 ............1" x 3/4"
SPR439168 ............1-1/4" x 1"
SPR439212 ...........1-1/2 x 1-1/4
SPR439251 ...........2" x 1-1/2"
PVC Tee
SPR405005 ............1/2" FNPT
SPR405007 ...........3/4" FNPT
SPR405010 ...........1" FNPT
SPR405012 ...........1-1/4" FNPT
SPR405015 ...........1-1/2" FNPT
SPR405020 ...........2"
FNPT
PVC SCH80 Fittings
Couplings SCH80
SPR830005 ...........1/2" NPT
SPR830007 ...........3/4" NPT
SPR830010 ...........1" NPT
SPR830012 ...........1-1/4" NPT
SPR830015 ...........1-1/2" NPT
SPR830020 ...........2"
NPT
PVC Caps
SPR448003 ............3/8"NPT
SPR448005 ...........1/2" NPT
SPR448007 ............3/4" NPT
SPR448010 ...........1"
NPT
SPR448012 ...........1-1/4" NPT
SPR448015 ...........1-1/2" NPT
SPR448020 ...........2"
NPT
SPR448025 ...........2-1/2" NPT
SPR448030 ............3"
NPT
Plugs
SPR450003 ............3/8" NPT
SPR450005 ...........1/2" NPT
SPR450007 ...........3/4" NPT
SPR450010 ...........1"
NPT
SPR450012 ...........1-1/4" NPT
SPR450015 ............1-1/2" NPT
SPR450020 ...........2"
NPT
SPR450025 ...........2-1/2" NPT
SPR450030 ...........3"
NPT
SPR450040 ...........4"
NPT
PVC Nipples PVC SCH 80
SPR884005 ...........1" x CLOSE
SPR884020 ...........1" x 2"
SPR884030 ...........1" x 3"
SPR884040 ...........1" x 4"
SPR884050 ...........1" x 5"
SPR884060 ...........1" x 6"
Nipples PVC SCH 80
SPR885005 ...........1-1/4" x CLOSE
SPR885020 ...........1-1/4" x 2"
SPR885030 ...........1-1/4" x 3"
SPR885040 ...........1-1/4" x 4"
SPR885050 ...........1-1/4" x 5"
SPR885060 ...........1-1/4" x 6"
Nipples PVC SCH 80
SPR886005 ...........1-1/2" x CLOSE
SPR886020 ...........1-1/2" x 2"
SPR886030 ...........1-1/2" x 3"
SPR886040 ...........1-1/2" x 4"
SPR886060 ...........1-1/2" x 6"
Nipples PVC SCH 80
SPR887005 ...........2" x CLOSE
SPR887030 ...........2" x 3"
SPR887040 ...........2" x 4"
SPR887060 ...........2" x 6"
Seattle: (206) 285-5010 Fax: (206) 285-7925
347
Hose Clamps
Stainless Steel T Bolt Hose Clamp
Stock #
Description
Size:
1-1/2” T-B SS
1-3/4” T-B SS
1-7/8” T-B SS
2”
T-B SS
2-1/4” T-B SS
2-3/8” T-B SS
2-1/2” T-B SS
2-5/8” T-B SS
2-3/4” T-B SS
2-7/8” T-B SS
3”
T-B SS
3-1/8” T-B SS
3-1/4” T-B SS
3-1/2” T-B SS
3-3/4” T-B SS
4”
T-B SS
4-1/4” T-B SS
4-1/2” T-B SS
4-3/4” T-B SS
5”
T-B SS
5-1/4” T-B SS
5-1/2” T-B SS
6”
T-B SS
6-1/2” T-B SS
7”
T-B SS
7-1/2” T-B SS
8”
T-B SS
8-1/2” T-B SS
8-3/4” T-B SS
8-7/8” T-B SS
9”
T-B SS
Stainless Steel Hose Clamp
AWAB, stainless steel.
Stock #
Stainless Steel Hose Clamp
Stock #
Description
Size / Inches
BANV202 ..............Clamp Hose SS #2 ................ 7/32” - 5/8”
BANV203 ..............Clamp Hose SS #3 ................ 5/16” - 7/8”
BANV006 ..............Clamp Hose SS #6 ................. 7/16” - 7/8”
BANV008 ..............Clamp Hose SS #8 ................. 7/16 ”- 1”
BANV010 ..............Clamp Hose SS #10 ............... 1/2” - 1-1/8”
BANV012 ..............Clamp Hose SS #12 .............. 5/8” - 1-1/4”
BANV024 ..............Clamp Hose SS #24 ..............1-1/8” - 2”
BANV028 ..............Clamp Hose SS #28 ..............1-1/4” - 2-1/8”
BANV040 ..............Clamp Hose SS #40 .............. 2” - 2-7/8”
BANV104 ..............Clamp Hose SS #104 ............5-1/8” - 7”
Call Toll Free: (800) 426-2783 8-5 M-F
Description
PMC10 ...................Clamp Hose SS 5/16-13/32
PMC11 ...................Clamp Hose SS 23/64-29/64
PMC11-17 ..............Clamp Hose SS US Size #4
PMC12 ...................Clamp Hose SS 25/64-31/64
PMC13 ...................Clamp Hose SS 7/16-17/32
PMC14 ...................Clamp Hose SS 15/32-9/16
PMC140-178 ..........Clamp Hose SS US Size #104
PMC15 ...................Clamp Hose SS 33/64-39/64
PMC16 ...................Clamp Hose SS 35/64-41/64
PMC17 ...................Clamp Hose SS 19/32-11/16
PMC256-283 ..........Clamp Hose SS #180 Dscv
PMC319014 ...........Clamp Outbrd Fuel SAE #3
PMC319014D ........Clamp Outboard Fuel SAE #3 2cd
PMC8 .....................Clamp Hose SS 15/64-21/64
PMC89-114 ............Clamp Hose SS US Size #64
PMC89-127 ............Clamp Hose SS US Size #72
PMC125015 ...........Red Tail Tip 100/Pk Chicklet
PMC125015P .........Red Tail Tip 25/Pk Chicklet
Pumps & Plumbing
DIXSTBC150 ........Clamp Hose
DIXSTBC8000 ......Clamp Hose
Seattle: (206) 285-5010 Fax: (206) 285-7925

Pumps - Seattle Marine and Fishing Supply Co.

Transcription

Similar documents

Mineflex Brochure - Reel Easy

Booster Pump Filter Cleaner v1

BEST VALUE DUAL WAND- MORE SUCK FOR YOUR BUCK

SCP 5000 - Karcher Cleaning Equipment

Napa Unicoil sellsheet Dealer copy.indd

Autocirc® Instant Hot Water Pump

INDUSTRIAL PUMP SOLUTIONS

Portable RV Waste Pump - Xylem Flow Control

GOLDENHORN 12S

UNICOIL Hose Bender Flyer