Cable Trays and Integrated Ceilings

Transcription

Cable Support Systems
Cable Trays and
Integrated Ceilings
06
Index
Cable trays & accessories
Bends, Junctions, Risers
Adjustable bend W10/40
90° Bend W10/40
90° Bend W10/60
90° Bend W10F/40
90° Bend W4
T-joint W9/40
T-joint W9/60
T-joint W29/40
T-joint W29/60
T-junction W12/40
T-junction W12/60
T-junction W12F/40
X-junction W13/40
X-junction W13/60
X-junction W13F/40
Vertical riser W11/40
Vertical riser W4, interior
Vertical riser W4, exterior
page
Reducers
Reducer W28/40
Reducer W28/60
Reducing piece W14/40 left
Reducing piece W14/40 left Hdg
Reducing piece W14/40 right
Reducing piece W14/40 right Hdg
Reducing piece W15/40 straight
Reducing piece W15/40 straight Hdg
Brackets
Angle bracket W8
Angle bracket W8S
Bracket 60/40
Combi bracket 53
Cover clamp W62
End bracket WN17
Luminaire bracket W25/40
Luminaire bracket W35
Pendant attachment W21
Pendant bar 1
Pendant bracket W80, W81
Tube pendant attachment W73
Wall bracket 80
Cable trays
Cable tray W1/40 Pre-galv
Cable tray W3/40 Hdg
Ceiling mesh tray WN2
Fixing tray N for casting-in
Installation tray W4
Lighting trunking W70
30
54
32
56
33
77
27
52
28
53
34
57
35
36
58
37
31
55
78
79
26
51
38
39
40
41
59
60
42
43
61
105
106
94
116
115
104
45
65
71
118
72
72
86
95
71
87
83
18
46
21
20
47
108
107
75
68
69
page
Cantilever arms
Adjustable cantilever arm W1840
23
48
Cantilever arm 50L, 50
80-81
Cantilever arm 80
82
Internal cantilever arm W17/40
22
Cantilever arms – accessories
Back plate W30
83
Mounting rail 40
84
Wall bracket 80
83
Ceiling brackets
Ceiling attachment W31
98
Ceiling bracket 5
93
Ceiling bracket 7
88
Ceiling bracket WN16
109
Clamps
Cover clamp W62
115
Earth clamp W79
109
Locking clamp W77
98
Covers
Cover plate W16
110
Cover strip W47/60
66
Cover W5
114
End cover W45/40
29
End cover W45/60
62
Dividers
Dividing strip 39
111
Dividing strip 39/55
64
Insert piece W39
112
Insert piece W39/55
65
Strip fixing W44
117
Support band W6
64 and 112
End plugs
End plug 28C,D,E and F
92
End plug 7
90
Protection strip W48
117
Fixings
Adapter TLF-A12
137
Angled bracket TLF-F12 137
Bitro adapter
131
Bits holder
132
Concrete screws
125-129
Expansion bolts
122
Expansion nail
130
Express hanger SVH
138
Eye screw
130
Fixing strips
140
Hammer drill SDS plus
133
Hammer tool TLF-S
136
Light concrete screw
130
Low density anchor TLF
135
Magnetic socket for Concrete screw 131
Mounting tool for Eye screw
130
Mounting tool SVH-T
139
Securing spring SVH-L
139
Sleeve TLF-H12
136
Socket for Concrete screw
131
Square peg
132
Fixings
Torxbits
Installation summeries
Cable trays
Suspension components
Joints
Joint W2
Side joint W49/40
Side joint W49/60
Junction box plates
Junction box plate W24/40
page
132
14-15
74
16-17
76
26
51
44
63
Lashing wires
Lashing wire
108
Mesh trays
Wibe Defem system. See sep. brochure
Mounting rails
Mounting rail 40
Mounting rail WMS25
Ogebe fixings
Fixings Ogebe
Ogebe fixing type E
Ogebe fixing type D
Ogebe fixing type ED
Ogebe fixing type Eg
Paint
Anti-corrosive paint “Galvafroid”
Repair paint
84
84
141
142
143
144
145
Support brackets
Support bracket W1940
Support bracket W20
Support bracket W20A
Support bracket/joint W7/40
Surface treatment
Corrosion classes
Current load of cables Environment/Quality Potential balancing
Product certificates
Surface treatments Wibe reserve the right to make changes to manufacture and design without prior notice.
25
49
70
70
24
50
7
9
9
12
10-11
8
Tele-conduits
Tele-conduit 36 with knock-out holes 113
Integrated ceilings & accessories
Integrated ceilings
146
Acoustic lamina
147
Installation summaries
Ceilings in corridor
Ceilings with sound baffles
Ceilings with wire baskets
Open ceilings
Sound baffles
Wire baskets
W-swing in corridor
151
149
150
148
152
153
159
Sound baffles
Sound baffles - accessories
155-158
W-swing ceilings
Angle strip W46
Integrated channel W27/40
Pendant/Fixing rails, Vertical pieces Integrated channel W27/60
Fixing rail 24/26x53 for casting-in
99 Profile W-swing 1/40
Pendant/Fixing rail 24/34
91 Profile W-swing 1/60
Pendant/Fixing rail 7L,7
88 Profile W-swing 2
Pendant rail W32
Pendant strip W33
96 Profile W-swing 4A
Threaded rod M10 W76
Vertical piece 2
101 Shade ledge W26/40
Vertical piece 2F
102 Shade ledge W26/60
Vertical piece 2FPK
100 Wall bracket W-swing 2
Vertical piece 20
103 Wall tray W60/40
Vertical piece 7L, 7 89 Wall tray W60/60
Installation examples
Screw sets
Expansion bolts
122-123 Installation examples
Locking plug W41
120
Mounting set W78
119
Screw set 22S
119
Screw set W34
120
Screw set W36
119
Screw set W36C
119
Screw set W37
120
Screw set W38P
120
Screw W40
120
Spring nut M8
119
T-bolt 26F
121
118
118
page
167
166
167
160
160
161
163
164
165
165
166
162
168
168
169
Cable trays
Cable trays - view
4
Corrosion classes, Surface treatments, Current load of cables
7
Environmental policy and certification, Product certificates, Potential balancing
9
Cable trays – installation summary
14
Suspension components – installation summary
16
Cable tray system W1/40, W3/40
18
46
Lighting trunking system W70, W71
67
Installation tray system W4
73
Suspension components, common parts
Cantilever arms, Wall bracket, Back plate, Mounting rail
80
Threaded rod, Pendant attachments, Pendant/Fixing rails, Brackets
85
Pendant rails, Ceiling attachment, Vertical pieces
96
End bracket, Angle brackets, Fixing tray N
104
Ceiling mesh tray, Earth clamp, Cover plate, Dividing strip
108
Tele-conduit, Cover W5, Components
113
Screw sets,T-bolt, Expander bolts
119
Fixing system
124
Ogebe fixings
141
Integrated ceilings
146
169
1
Wibe in Mora, Sweden
There is always a next time.
Usually it’s a matter of a few extras, sometimes more radical changes. New and
old have to fit together regardless. Hand in glove – even in 15 years’ time.
We delivered our first – and the world’s first – cable ladder just over 75 years
ago. And we can still supply additions to it if necessary. We carry over 10,000
items in our range. Just over a hundred are ladders and trays. The remainder
consists of components to meet every possible requirement. And some pretty
impossible ones too.
So don’t just think about this time, think about the next time.
We are the biggest supplier on the market. More concretely, we provide cable
ladders and cable trays, lighting trunking and installation rails, steel wire systems, integrated ceilings – and Defem® mesh trays. We hot dip galvanize in one
of the most modern plants in Scandinavia and do powder coating in one that is
just as technologically advanced.
Wibe is the market leader in telescopic masts and masts for lighting and communication. We have experience from thousands of projects, from planning, to
fitting and erection, to commissioning and service.
Wibe is part of the worldwide Schneider Electric group, which also includes leading brands such as Eljo, Lexel, Merlin Gerin, Telemecanique and Thorsman.
2
3
Cable trays - view
Cable tray W1
Height
Length
Width
Pre-galvanized
Hot dip galvanized
Powder coated white
Electro-galvanized
Stainless steel AISI 316
4
Cable tray W3/40
40 and 60 mm
2000 and 3000 mm
70-600 mm
Height
Length
Width
Pre-galvanized
Hot dip galvanized
Powder coated white
Electro-galvanized
40 mm
3000 mm
50-600 mm
Cable trays - view
Cable tray W3/60
Height
Length
Width
Pre-galvanized
Hot dip galvanized
Powder coated white
Electro-galvanized
60 mm
3000 mm
50-600 mm
Height
Length
Width
15 mm
3000 mm
50-400 mm
Pre-galvanized
Hot dip galvanized
Powder coated white
Electro-galvanized
5
Cable trays - view
Lighting trunking W70, W71
Mesh trays
Wibe Defem system - see separate brochure
Height
Length
Width
Pre-galvanized
Hot dip galvanized
Powder coated white
Electro-galvanized
6
22 and 40 mm
3000 and 6000 mm
40-200 mm
Corrosion classes
The life expectancy of a cable support system is dependent on the
environment in which it is placed. Therefore, it is important to
establish the corrosive properties of an environment to ensure that
the right treatment and the right material are chosen.
To achieve this, several corrosion classes have been drawn up in
accordance with BSK99.
The table below shows various corrosion classes. As a guide, we
have included the surface treatment recommended by Wibe for
the different classes.
On the next page, we briefly outline the various surface treatments
and materials.
As regards environmental corrosion, a steel design component can usually be assigned to one of the corrosion classes (C1-C5-M)
as shown in table 1:23a. Reference values for the average level of corrosion in steel and zinc are given in table 1:23c.
The corrosion classes comply with those stipulated in SS-EN ISO 12944-2.
Table 1:23a
Corrosion classes as stipulated by SS-EN ISO 12944-2 with atmospheric corrosion levels and examples of the environment in which
they are most suitable for use.
7
Surface treatments
Electro-galvanized
Some of Wibe’s products are electro-galvanized in accordance with
ISO 2081. Such products are intended for use only in warm, dry
areas with negligible pollutant levels.
Pre-galvanized
Products are manufactured from Z 275 pre-galvanized sheet steel in
accordance with SS-EN 10142. Surface sections created during
cutting and drilling will, under normal conditions, repair themselves,
providing the plant with superb anti-corrosion protection.
Hot dip galvanized
Wibe has one of the most modern hot dip galvanization plants in the
Nordic countries. The hot dip process is continuous, guaranteeing a
high and even quality.
Once manufactured products are hot dip galvanized in accordance
with SS-EN ISO 1461 whilst nuts and bolts are hot dip galvanized in
accordance with SS-EN ISO 10684:2004. This form of galvanization
affords very good value-for-money anti-corrosion protection in
atmospheres with a pH value of between 6 and 13. However, in acidic environments where pH levels fall below 6 and in alkaline environments where the pH value exceeds 13, the protective zinc layer
breaks down relatively quickly.
Rate of dissolution
The rate of dissolution is determined by the pH value of pure zinc
in distilled oxygenated water that has been pH adjusted to various
levels using HCl or NaOH.
NB The curve only applies to conditions shown, and gives only
an indication of the propensity for corrosion without consideration
to time.
Zinkpox®
The Zinkpox® method involves the coating of the zinc layer with
a homogenous covering of epoxy/polyester.
Epoxy/polyester is a plastic paint that displays the greatest resistance to most chemicals.
The layer of zinc on the steel prevents the formation of underfilm
corrosion, which is a contributing factor in paint degradation.
The paint layer is only affected by atmospheric erosion.
The zinc layer only deteriorates once the paint has been eroded, and
this gives you considerable breathing room before the steel is subject
to attack.
By using this treatment process, the life expectancy of the product is
more than double that had it only been treated using hot dip galvanization.
In addition to providing excellent anti-corrosion protection, Zinkpox®
also allows freedom of choice as regards product colour. Powder
coating is an extremely environmentally friendly finishing method.
The pigment contains no solvents and has, to a great extent, replaced wet finishes.
In the case of visible cable tray installations, both trays and
accessories can be painted in colours matching the décor of their
surroundings.
8
Modern painting plant produces perfect results
Carefully and thoroughly pre-treating of galvanized products is the
cornerstone of achieving perfect adhesion.
We employ a nine-stage process, consisting of alkaline degreasing,
rinsing, rinsing, activation, zinc-manganese phosphatising, rinsing,
rinsing, passivation and rinsing with de-ionised water. Immediately
after the pre-treatment process, products are dried in a tunnel oven
and are then powder coated by an electronically controlled robot,
guaranteeing that all components are treated perfectly. Finally, the
coating is cured in a 24-section tunnel oven, the temperature in each
section being regulated in a stepless manner, producing a perfect
hardening curve. At no stage in the process does a human hand
touch any of the products. Instead, they are moved between the
various stages using a 355-metre long electronically controlled
conveyor belt. A perfect result! The surface is now resistant to both
scratches and impact.
Colour schemes
As standard, cable trays, lighting trunking, mounting fittings and accessories are painted white RAL9003 Gloss 30.
Other colours of your choice can also be offered.
If the powder-coated surface is broken, e.g. when cutting during
mounting, repair paint for minor damages can be supplied.
Quality - Epoxy/polyester
(very high chemical tolerance)
Zinc
Epoxy/polyester................(min 70 µm)
Lustre (ISO 2813)..............30
Finish (ISO 1519)...............6 mm
Cross hatch (ISO 2409)
Erichsen test (ISO 1520)....8 mm
Stainless steel
Wibe stainless steel products, manufactured in accordance with
SS 2333 AISI 304, or in accordance with SS 2348 AISI 316L are
designed for use in highly aggressive environments, either indoors or
outdoors, on industrial sites where there are high levels of potent airborne pollution such as in certain chemical industries, celluloserelated industries, refineries or artificial fertiliser factories, high
humidity tunnels, etc.
Stainless steel products are also ideal for use in environments where
special hygiene requirements are in force, such as dairies, abattoirs,
other food industries and pharmaceuticals factories.
Stainless steel AISI 304 or AISI 316L?
The deciding factor in choosing between stainless steel AISI 304 or
AISI 316L is the aggressiveness of the environment in which it is to
be used, and for this atmospheric chlorine content plays a significant
role. Environments with a high chlorine content - coastal areas
being a prime example - are aggressive and usually require the use
of AISI 316L materials.
When assessing the needs of factories, consideration should be
given to the materials previously used to suspend equipment such as
pipe tubing, and from this determine whether stainless steel AISI 304
or AISI 316L material is required.
Current load of cables
Installation instructions
Installation
The ladders and trays shall be installed in such a way that, as often
as possible the cables can be laid directly in place rather than being
pulled through.
Ladders and trays for current carrying cables along the ceiling shall
be installed in such a way that the distance from the top of the ladder
or tray to the ceiling shall not be less than 300 mm.
The free vertical distance between parallel ladders and trays shall be
at least 200 mm.
Ladders and trays near walls shall be installed with a minimum free
distance of 50 mm to the wall, so that cables can pass between the
ladders and the wall.
Ladders and trays along partition walls shall be installed with
minimum free distance of 100 mm to the wall.
Sharp edges and screw ends on ladders or trays should be removed
before the cables can be installed.
Expansion bolts for the installation of brackets/fixings shall be installed with such a distance between them, that the designated load
for ladders and trays will not be exceeded. When selecting the
distance between cantilever arms or brackets/fixings, the bearing
strength and designated load of the ladders and trays must be taken
into consideration.
Reinforced heavy duty cable ladders
Ladders shall be designed for a uniform load of at least 600 N
per 1000 mm ladder length with a distance of 6000 mm between
brackets/fixings. They shall also be able to carry an occasional point
load as to the heavy duty ladders.
Heavy duty cable ladders, cable trays
Ladders and trays shall be designed for a uniform load of at least
200 N per 1000 mm ladder length and 100 mm width with a distance
of 2000 mm between brackets/fixings. They shall also be able to
carry an occasional point load of 1000 N with a double safety factor
measured between supporting points 3 and 4 when using an
installation with six supporting points.
Light duty cable ladders, cable trays
Ladders and trays shall be designed for a uniform load of at least
100 N per 1000 mm ladder length and 100 mm width with a distance
of 2000 mm between brackets/fixings.
Environmental policy and certification
Environmental product declarations are available for all Wibe
products. These can be ordered direct from Wibe.
Declarations may also be downloaded from the Wibe website at
www.wibe.com
Our product sheets and brochures are marked successively with the
name of the environmental document (WEF-0001-).
Environmental policy
AB Wibe shall actively strive to minimise any negative impact its
operations may have on the environment.
Besides working in a way that prevents pollution, we shall also
ensure that, given Wibe’s production and quality requirements, the
most environment-friendly solutions are always chosen. All of this
shall be within a framework of continual improvement.
Our environmental initiatives shall go beyond what is required by
legislation.
In its work for the environment, Wibe shall maintain suitable
dialogues and collaborations with all interested parties.
The environmental policy shall always be available to the public.
The company’s environmental reviews shall be the base on which
our environmental goals and programmes are founded.
We shall achieve the above by:
Management system - Quality and Environment
Wibe has a third-party certified management system
for quality and environment in accordance with
ISO 9001:2000 and ISO 14001:2004
CE-marking of products
is placed on the product or on the packing according to
"Declaration of Conformity" (D o C), applicable to Wibe Cable
ladders, Cable trays and Lighting trunkings.
EMC directive 89/336 EEC
Above mentioned products are neutral according to the EMC
directive 89/336 EEC.
Low voltage directive 73/23 EEC
According to the low voltage directive we refer to:
SFS 1993:1068 Regulations concerning electrical material.
SFS 1993:1068 General obligations regarding electrical material.
Wibe fulfils the demands according to the harmonized standard
SS-EN 6153 Edition 1:2002.
• Ensuring that, throughout manufacture and design, full attention is
paid to ecological considerations, quality requirements, health
factors and environmental sustainability
• Setting up environment-focused collaborations with suppliers and
customers
• Giving training on our environmental initiatives and promoting staff
involvement
• Maximising efficiency in the use of energy and raw materials
• Minimising the production of waste that cannot be recycled within
our operations
• Ensuring that chemicals and dangerous waste are handled in the
best possible manner
• Continuously evaluating the success of our initiatives
9
10
11
Potential balancing
Resistance testing of Wibe cable trays has been performed by
the Swedish National Testing & Research Institute in Borås and
Wibe test laboratory.
12
The tests have been carried out according to SS-EN 61537,
IEC 61537 and EL-AMA SBD 2.
Potential balancing
13
Installation
summary
Potential
balancing
4
64
35
33
61
53
35
21
51
49
32
55
31
44
17
2
1
50
51
52
21
63
62
18,19
2
16
62
36
39
5
60
37
22
3
25
20
22
30
29
26
28
14
42
41
7
25
59
40
28
47
23,24
9
45
32
14
Potential balancing
Components
54
46
34
5
56
45
7
11
12
8
43
13
48
46
6
45
1
15
38
7
10
58
57
14
27
27
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
3
61
62
63
64
Cable tray W1/40
Cable tray W3/40
Mesh trays – Wibe Defem system
Installation tray W4 (system)
Side joint W49/40
T-joint W9/40
T-joint W29/40
End cover W45/40
90° bend W10/40
T-junction W12/40
X-junction W13/40
Support bracket W20
Pendant brackets W80 and W81
Cantilever arm 50
Cantilever arm 80
Wall bracket 80
Back plate W30
Mounting rail WMS25
Threaded rod M8 W76
Threaded rod M10 W76
Pendant/Fixing rail 7L, 7
Ceiling bracket 7
Vertical piece 7L, 7
Pendant bar 1
Pendant strip W33
Pendant rail W32
Locking clamp W77
Vertical piece 2F
Angle bracket W8
Earth clamp W79
Cover plate W16
Dividing strip 39
Insert piece W39
Support band W6
Tele-conduit 36
Cover W5
Cover clamp W62
Strip fixing W44
Screw sets
Fixing system
Fixings - Ogebe
Integrated ceilings
Sound baffles and accessories
Profile W-swing
Wall tray W60/40 and W60/60
1Page
18
20-21
46-66
73-79
22
23
24
25
26
27
28
29
30
31
32-33
34-35
36-37
38-39
40-41
42-43
44
45
68
69
70
70
71
71
72
72
80
82
83
83
84
85
85
86
87
88
88
89-90
95
96
97
98
98
102
105
107
109
110
111
112
112
113
114
115
117
118
119-123
124-140
141-145
146-168
155-158
160-167
168
15
Common balancing
parts, suspension components
Potential
31
20
20
38
20
20
20
30
18
18
18
18
18
13
12
33
26
11
9
10
8
28
32
25
31
20
31
20
20
29
18
18
18
30
25
30
20
19
36
35
19
20
14
3, (7)
4, (6)
16
Potential balancing
34
22
23
27
38
25
21
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
Components
1Page
Support bracket W20-70
Support bracket W20A-70
Pendant bracket W80
Pendant bracket W81
Cantilever arm 50
Cantilever arm 80
Wall bracket 80
Back plate W30
Threaded rod W76
Pendant/Fixing rail 7L,7
Ceiling bracket 7
End plug 7
Ceiling bracket 5
Bracket 60/40
Pendant bar 1
Pendant strip W33
Pendant rail W32
Vertical piece 2
Vertical piece 2F
Vertical piece 20
Angle bracket W8
Angle bracket W8S
Screw sets
Fixing system
22
23
24
25
48
49
50
70
70
70
70
71
71
80
82
83
83
85
86
87
88
88
89-90
90
91
93
94
95
96
97
98
101
102
103
105
106
119-123
124-140
16
17
24
15
2, (5)
1
17
Potential
Cable
traybalancing
W1/40, unperforated
WEF-0001
Side height 40 mm, length 2000 and 3000 mm. Secondary trays 1300-1800 mm.
Holes Ø5,8 mm at the tray ends can be used for locking of joints.
A
mm
L
mm
Cable tray W1/40-70
70 2000
Cable tray W1/40-100
100 2000
200 2000
300 2000
400 2000
500 2000
600 2000
Cable tray W1/40-500 FS
500 2000
600 2000
Secondary W1/40-200
200 1300
Secondary W1/40-200
200 1600
Secondary W1/40-200
200 1800
Cable tray W1/40-70
70 3000
100 3000
200 3000
300 3000
400 3000
500 3000
600 3000
*EAN-code=732167+Part.no+C (control figure)
Plate thickness
mm
Pre-galv.
Part.No. C*
Pre-galv. White30
Part.No. C*
Weight kg
100 m
0.7
0.7
0.7
1.25
1.25
1.5
1.5
1.5
1.5
0.7
0.7
0.7
0.7
0.7
0.7
1.25
1.25
1.5
1.5
713251 5
713252 2
713254 6
713256 0
713257 7
713258 4
723219 2
786831 5
786832 2
728986 8
728987 5
728988 2
728989 9
728990 5
728991 2
728992 9
786833 9
786834 6
737504 2
737505 9
737506 6
781334 6
781335 3
781336 0
781337 7
781338 4
781339 1
781340 7
95
115
170
400
500
710
825
715
830
170
170
170
95
115
170
400
500
710
825
Use and installation
Cable tray W1/40 is joined with
2 Side joints W49/40 or Support
bracket/joint W7/40.
18
For trays 300 mm and wider we
recommend to use Support
720822 7
720984 2
720985 9
726664 7
726665 4
726666 1
726667 8
Cable tray W1/40, unperforated
WEF-0001
Loadings
In order to calculate the total deflection in the middle of the tray:
add up transversal deflection + longitudinal deflection + deflection of unloaded tray.
Transversal deflection
Deflection of unloaded tray
Tray, length 2 m
Transversal deflection at 0 kg
Longitudinal deflection at 0 kg
Longitudinal deflection
W1/40-100-200
0 mm
5 mm
W1/40-300-400
3 mm
5 mm
W1/40-500-600
5 mm
6 mm
19
Cable tray W3/40, perforated
WEF-0001
Pre-galvanized
Side height 40 mm, length 3000 mm.
Holes Ø5.8 at the tray ends can be used for locking of joints.
Oval holes along the tray sides can be used for mounting of accessories.
A
mm
Cable tray W3/40-50
50
Cable tray W3/40-70
70
100
150
200
300
400
500
600
L
mm
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 m
3000
3000
3000
3000
3000
3000
3000
3000
3000
1.0
1.0
1.0
1.0
1.0
1.25
1.25
1.5
1.5
735388 0
735389 7
735390 3
735391 0
735392 7
735393 4
735394 1
735395 8
735396 5
737537 0
737538 7
737539 4
737540 0
737541 7
737542 4
737543 1
737544 8
737545 5
103
120
136
170
196
316
390
590
683
20
WEF-0001
Hot dip galvanized
Holes Ø5.8 at the tray ends can be used for locking of joints.
Oval holes along the tray sides can be used for mounting of accessories.
A
mm
Cable tray W3/40-50
50
Cable tray W3/40-70
70
100
150
200
300
400
500
600
L
mm
Plate
thickness
mm
Hot dip galv.
Part. No. C*
ZINKPOX®
White80
Part.No. C*
Weight kg
100 m
3000
3000
3000
3000
3000
3000
3000
3000
3000
1.0
1.0
1.0
1.0
1.0
1.25
1.25
1.5
1.5
735400 9
735401 6
735402 3
735403 0
735404 7
735405 4
735406 1
735407 8
735408 5
735412 2
735413 9
735414 6
735415 3
735416 0
735417 7
735418 4
735419 1
735420 7
110
120
156
170
220
350
453
620
723
bracket/joint W7/40
21
WEF-0001
For mounting inside Cable trays W1/40 and W3/40.
Internal
cantilever arm
A
mm
B
mm
C
mm
D
mm
W17/40-100
89 140 70 55
W17/40-200
189 140 70 55
W17/40-300
289 165 95 75
W17/40-400
389 165 95 75
E
mm
Pre-galv.
Part. No. C*
Hot dip Galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
42
42
55
55
716911 5
716912 2
716913 9
716914 6
734572 4
734573 1
734574 8
734575 5
729029 1
729030 7
729031 4
729032 1
783066 4
783067 1
783068 8
783069 5
16
35
80
100
Loading table for Internal cantilever arm W17/40 on wall
F
Mounted onto wall with Expansion
bolt.
Breaking load for cantilever arm
mounted onto wall, see below.
Type of
cantilever arm
W17/40-100
W17/40-200
W17/40-300
W17/40-400
Max load F at 3˚ deflection
of cantilever arm
kN
kg
1.0
0.8
1.1
1.0
100
80
110
100
Deflection in mm at 3˚ deflection
of cantilever arm
5.2
10.5
15.7
20.9
Breaking load
kN
kg
3.0
2.0
3.0
2.0
300
200
300
200
Internal cantilever arm W17/40 is
mounted on Vertical piece 2F
using a T-bolt.
22
When mounting an Internal cantilever arm W17/40 on a porous
wall or when surface pressure
must be reduced use Mounting
rail 40.
The Internal cantilever arm is
mounted onto the wall with an
Expansion bolt alt. a Concrete
screw.
can be mounted right over
support bracket/joint.
For installation inside Cable trays W1/40 and W3/40.
Adjustable
cantilever arm
A
mm
B
mm
C
mm
D
mm
W1840-100
88 160 70 0-25
W1840-200
188 160 70 0-50
W1840-300
289 185 95 0-50
W1840-400
389 185 95 0-50
W1840-500
489 185 95 0-50
W1840-600
589 185 95 0-50
WEF-0001
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
718360 9
718361 6
783587 4
783588 1
783589 8
783590 4
734578 6
734579 3
734580 9
734581 6
734582 3
734583 0
729033 8
729034 5
783591 1
783592 8
783593 5
783594 2
783018 3
783019 0
783020 6
783021 3
783022 0
783023 7
36
47
120
139
156
175
Loading table for cantilever arm W1840 on wall
Mounted onto wall with Expansion bolt.
mounted onto wall - see below.
Type of
cantilever arm
of cantilever arm
kN
kg
W1840-100
W1840-200
W1840-300
W1840-400
W1840-500
W1840-600
1.0
0.8
1.1
1.0
0.65
0.5
100
80
110
100
65
50
Deflection in mm at 3˚ deflection
of cantilever arm
5.2
10.5
15.7
20.9
26
31.5
Breaking load
kN
kg
3.0
2.0
3.0
2.0
1.3
1.0
300
200
300
200
130
100
Mounting directly onto wall.
At this type of installation the
adjusting allowance of the tray is
limited.
Breaking load - see table above.
Mounting on Vertical piece 2F
using T-bolt. The Cantilever arm
W1840 can be adjusted to a
max. of 50 mm.
Mounting of two adjustable cantilever arms on the same Vertical
piece 2F. (Tray widths more than
400 mm).
Use Screw set 20S if the two
trays have the same width.
At different tray widths T -bolt
and Screw set W37 must be
used.
When mounting cable trays width 500-600 mm - it might be
necessary with a reinforcement
of the cantilever arm. Installation
band and stretching screw can
be used for mounting in ceiling or
on a vertical piece.
23
Used as a support bracket or joint for Cable tray W1/40 and W3/40 and for Lighting trunking W70/W71.
When joining Cable tray W1/40 FS (reinforced), Side joint W49/40 must be used.
W7/40-70,100,200,300,400
WEF-0001
W7/40-50,150,500,600
W7/40-40
Support bracket/
joint
A
mm
B
mm
Plate
thickness
mm
W7/40-40
36 180
W7/40-50
48 200
W7/40-70
68 200
W7/40-100
98 200
W7/40-150
148 200
W7/40-200
198 200
W7/40-300
297 300
W7/40-400
397 300
W7/40-500
498 300
W7/40-600
598 300
1.5
1.0
1.0
1.0
1.0
1.0
1.25
1.25
1.25
1.25
Pre-galv
Part. No. C*
Hot dip galv.
Part. No. C*
718480 4
734554 0
720825 8
717021 0
734555 7
717022 7
717023 4
717024 1
720990 3
723180 5
734556 4
734557 1
734558 8
734559 5
734560 1
734561 8
734562 5
734563 2
734564 9
Pre-galv.
White30
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
783080 0
783081 7
783082 4
783083 1
783084 8
783085 5
783086 2
783087 9
783088 6
12
14
16
25
35
43
110
140
170
200
729053 6
729046 8
729047 5
729048 2
729049 9
729050 5
729051 2
729052 9
Support bracket/joint W7/40 is
used for straight joining. Push-in
mounting.
If necessary trays and lighting
trunkings are locked using Screw
set W38P or Locking plug W41.
The Joint W7/40-40 is locked
with Screw set W36/W36C at the
bottom of the trunking.
With Pendant attachment W21
installed on Support bracket/joint
W7/40-100, 200, 300 or 400 a
complete support bracket is
obtained.
W7/40-50, 150, 500 and 600 are
only used for joining, not as support brackets.
Reinforced tray is to be joined
with Side joint W49/40.
End bracket WN17 can be used
as vertical piece on Support
bracket/joint W7/40 mounted
with Screw set W36/W36C.
used to achieve an invisible
suspension in or in connection
with bends or junctions, here with
End bracket WN17 mounted as
vertical piece.
24
or the one half of Pendant
attachment W21 are mounted
on
Support bracket/joint W7/40-70,
100, 200, 300 or 400 with Screw
set W36/W36C.
WEF-0001
A
Support bracket
A
mm
W1940-100
90
W1940-200
190
W1940-300
289
W1940-400
389
W1940-500
489
W1940-600
589
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
718711 9
734401 7
734402 4
734403 1
782342 0
782343 7
734452 9
734453 6
734454 3
734455 0
734456 7
734457 4
729041 3
729042 0
729043 7
729044 4
783753 3
783754 0
783060 2
783061 9
783062 6
783063 3
783064 0
783065 7
11
22
50
68
91
110
Tray W1/40 and W3/40 with
widths of 200 to 400 are
mounted with suitable Support
bracket W1940, Pendant rail
W32, Pendant attachment
W21, Screw sets W37 and W36/
W36C.
Trays with width 100 can be
mounted with Support bracket
W1940-100, one half of Pendant
attachment W21 or Tube
pendant W73 and Screw set
W36/W36C.
Support bracket W1940 mounted
with Ceiling bracket 5, Pendant/
Fixing rail 24/34 and Angle
bracket W8S. Screw set 22S
must be used. For cable trays
with width 500 and 600.
on Vertical piece 2 and Ceiling
bracket 5. Screw set 22S must
be used. For cable trays with
width 500 och 600.
Support bracket W1940 can be
mounted with Vertical piece 2,
Pendant joint 2J, Pendant/Fixing
rail 24/34 and Ceiling bracket 5.
Screw set 22S must be used.
For cable trays with width 500
and 600.
Alternatively, Tray W1/40 and
W3/40 with widths 500 and 600
can be installed with suitable
Support bracket W1940,
Threaded rod M10 W76 and
2 M10 nuts.
Tube pendant attachment W73.
Pendant rail W32, Pendant
attachment W21 and Screw set
W37.
Tray W1/40 and W3/40 can be
mounted on suitable Support
bracket W1940 and 2 End
bracket WN17 as pendant.
The end brackets are joined with
2 Screw sets 22S and can be
adjusted in height. The pendant
can be mounted in the support
bracket with Screw set W36/
W36C.
25
Side joint W49/40
WEF-0001
For straight joining of Cable tray W1/40 and W3/40.
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
Side joint W49/40
786837 7
730191 1
*EAN-code=732167+Part.no+C (control figure) **Produced to order
Pre-galv.
White30
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
786838 4
790231 6**
17
2 Side joints W49/40 are used
for straight joining of Cable tray
W1/40, W1/40 FS and W3/40.
4 Screw sets W38P are required
(not included).
Reducer W28/40
WEF-0001
Used for transition joining from a wider to a narrower cable tray.
Reducer W28/40-100
Reducer W28/40-200
*EAN-code=732167+Part.no+ (control figure)
A
mm
B
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
100
200
37.5
37.5
787436 1
787437 8
787438 5
787439 2
17
23
Used together with 1 Side joint
W49/40 at one-side transition
joining of Cable tray W1/40 and
W3/40, to be mounted with 2
Screw sets W38P. Always use
support close to the reducer.
26
2 Reducers W28/40 are used at
centered transition joining, to be
mounted with Screw set W38P.
Always use support close to the
reducer.
T-joint W9/40
WEF-0001
Mounted in T- or X-branches. Also used for oblique branches.
Part. No. includes 2 T-joints W9/40
Plate
thickness
mm
T-joint W9/40
1.0
(Screw set W38P incl)
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
718205 3
734622 6
729094 9
783128 9
6
1
2
Potential balancing
In order to fulfil the potential
balancing according to SS-EN
61537 the T-joint must be
secured with
1 Self-drilling screw
RXB 4.2 x 13
2 Screw set W38P,
drilling is required.
Tightening torque 2 Nm.
T-joint W9/40 is mounted on the
side edges of the tray with Screw
set W38P.
Straight angling. If necessary, the
lugs are locked to the edge of the
tray using pliers. Can also be
locked with blind rivets or selftapping screws.
Oblique angling. If necessary, the
lugs are locked to the edge of the
tray using pliers. Can also be
locked with blind rivets or selftapping screws.
27
T-joint W29/40
WEF-0001
Simple push-in assembly.
Is hung over the edge of the tray and locked in a suitable way.
T-joint W29/40-70
T-joint W29/40-100
T-joint W29/40-200
T-joint W29/40-300
T-joint W29/40-400
T-joint W29/40-500
T-joint W29/40-600
A
mm
B
mm
Pre-galv.
Part. No. C*
Pre-galv.
White 30
Part. No. C*
Weight kg
100 pcs
68
98
198
301
401
501
601
120
220
320
420
520
790984 1
790985 8
790986 5
790987 2
790988 9
790989 6
790990 2
724942 8
724943 5
724944 2
724945 9
724946 6
724947 3
724948 0
8
12
21
30
40
50
59
Potential balancing
balancing according to SS-EN
61537 the T-joint must be
secured with
RXB 4.2 x 13
2 Screw set W38P,
Tightening torque 2 Nm.
Simply installed with push-in
mounting. Lock into tray with
Screw set W38P.
Used with T- and X-junction.
Mounted directly onto tray edge.
Can be attached to tray by
pinching the lip at the top of the
tray.
Used with open junction together
with Joint W7/40 with opening
and Tray W1/40 with opening.
Attached with Screw set W38P.
Examples of suspensions with open junction where T-joint W29/40, Tray W1/40 with opening and Joint W7/40 with opening are included.
Suspension with Pendant strip
W33.
28
Suspension with Pendant rail
W32 and half a Pendant attachment W21.
Suspension with End bracket
WN17.
Suspension with wire and Ogebe
fixing type E.
End cover W45/40
WEF-0001
For push-in assembly. Mounted as end cover in Cable trays W1/40 and W3/40 and lighting trunking.
A
mm
End cover W45/40-70
68
End cover W45/40-100
98
148
198
298
398
498
598
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
731730 1
731731 8
783030 5
783031 2
783032 9
783033 6
783034 3
783035 0
783036 7
783037 4
731732 5
731733 2
731734 9
731735 5
731736 1
Pre-galv.
White30
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
729177 9
729178 6
783000 8
783001 5
783002 2
783003 9
783004 6
783005 3
783006 0
783007 7
8
9
10
12
15
18
21
24
729179 3
729180 9
729181 6
729182 3
729183 0
Mounted as end in trays and
lighting trunking. Locked with
Locking plug W41 or Screw set
W38P.
29
WEF-0001
Adjustable bend W10/40 permits horizontal angling from 105º to 165º in steps of 7.5º.
Push-in installation.
A
mm
Plate
thickness
mm
Adjustable bend W10/40-50
47
1.0
67
1.0
97
1.0
147
1.0
197
1.0
297
1.0
397
1.0
497
1.25
Adjustable bendW10/40-600
597
1.25
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
734584 7
716833 0
716834 7
734585 4
716835 4
716836 1
716837 8
724965 7
724966 4
734591 5
734592 2
734593 9
734594 6
734595 3
734596 0
734597 7
734598 4
734599 1
Pre-galv.
White30
Part. No. C*
729103 8
729104 5
729105 2
729106 9
729107 6
729108 3
729109 0
V
Push-in installation. Turn up
inner and outer sides and mount
the Adjustable bend W10/40
inside the tray.
30
Adjustable bend W10/40 permits
desired horizontal angling
between 105º and 165º in stages
of 7.5º.
If necessary, Adjustable bend
W10/40 may be locked using
Screw set W38P or Locking plug
W41.
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
782850 0
782851 7
782852 4
782853 1
782854 8
782855 5
782856 2
782857 9
782858 6
9
10
13
24
40
75
125
270
380
WEF-0001
For upward or downward angling to a desired angle up to 90˚, push-in assembly.
Should be locked with Screw set W38P or Locking plug W41.
Vertical riser
A
mm
L
mm
Plate
thickness
mm
W11/40-50
48 150
0.7
W11/40-70
68 150
0.7
W11/40-100
98 150
0.7
W11/40-150
148 150
0.7
W11/40-200
198 200
0.7
W11/40-300
298 200
0.7
W11/40-400
398 200
0.7
W11/40-500
498 200
0.7
W11/40-600
598 200
0.7
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
733498 8
723226 0
723227 7
733499 5
723228 4
723229 1
723230 7
723231 4
723232 1
734101 1
734102 3
734103 0
734104 7
734105 4
734106 1
734107 8
734108 5
734109 2
Pre-galv.
White30
Part. No. C*
729126 7
729127 4
729128 1
729129 8
729130 4
729131 1
729132 8
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
783040 4
783041 1
783042 8
783043 5
783044 2
783045 9
783046 6
783047 3
783048 0
8
10
12
17
28
39
50
61
73
For upward or downward angling at a desired angle up to 90˚.
Should be attached with Screw set W38P or Locking plug W41.
Vertical riser W11/40 is delivered
flat and must be bent by the
installer on the job site.
31
90˚ bend W10/40
WEF-0001
Pre-galvanized
For 90˚ horizontal junction of Cable trays W1/40 and W3/40.
Push-in assembly.
A
mm
90˚ bend W10/40-70
67
90˚ bend W10/40-100
97
90˚ bend W10/40-200
197
90˚ bend W10/40-300
297
90˚ bend W10/40-400
397
90˚ bend W10/40-500
497
90˚ bend W10/40-600
597
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
1.25
1.25
1.25
1.25
1.25
1.25
1.25
717903 9
717904 6
717905 3
717906 0
717907 7
721184 5
723196 6
729201 1
729133 5
729134 2
729135 9
729136 6
729137 3
729138 0
38
51
108
185
281
400
540
Used for 90˚ horizontal angling.
Suspension components should
be mounted in or in connection
with the junction.
32
If necessary, the 90˚ bend W10/
40 can be locked using Screw
Can be provided with holes in
bottom for suspension in
Pendant attachment W21 alt.
W73.
Valid for max. width 200 mm.
Support bracket/joint W7/40, with
a suitable pendant, is used to
achieve an invisible suspension,
here with End bracket WN17
mounted as vertical piece.
90˚ bend W10F/40
WEF-0001
Hot dip galvanized
Push-in assembly.
A
mm
L
mm
Plate
thickness
mm
Hot dip galv.
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
90˚ bend W10F/40-50
47
90˚ bend W10F/40-70
67
90˚ bend W10F/40-100
97
90˚ bend W10F/40-150
147
90˚ bend W10F/40-200
197
90˚ bend W10F/40-300
297
90˚ bend W10F/40-400
397
90˚ bend W10F/40-500
497
90˚ bend W10F/40-600
597
119
153
204
290
375
480
580
714
814
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
783660 4
783661 1
783662 8
783663 5
783664 2
783665 9
783666 6
783667 3
783668 0
783600 0
783601 7
783602 4
783603 1
783604 8
783605 5
783606 2
783607 9
783608 6
18
28
48
92
148
242
353
528
685
with the junction.
33
T-junction W12/40
WEF-0001
Pre-galvanized
Push-in assembly.
A
mm
T-junction W12/40-70
67
97
197
297
397
497
597
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
1.25
1.25
1.25
1.25
1.25
1.25
1.25
717908 4
717909 1
717910 7
717911 4
717912 1
721186 9
723198 0
729139 7
729140 3
729141 0
729142 7
729143 4
729144 1
729145 8
49
64
128
212
314
438
580
Used for horizontal 90˚ junction. Suspension components should be
mounted in or in connection with the junction. Push-in installation.
34
If necessary, the T-junction W12/40 can be locked using Screw set
W38P or Locking plug W41.
Can be provided with holes in bottom for suspension in Pendant
attachment W21 or Tube pendant attachment W73. Valid for max.
width 200 mm.
T-junction W12F/40
WEF-0001
Hot dip galvanized
Push-in assembly.
A
mm
T-junction W12F/40-50
47
67
97
147
197
297
397
497
597
L
mm
Plate
thickness
mm
Hot dip galv.
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
171
219
312
432
553
662
762
932
1032
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
783670 3
783671 0
783672 7
783673 4
783674 1
783675 8
783676 5
783677 2
783678 9
783620 8
783621 5
783622 2
783623 9
783624 6
783625 3
783626 0
783627 7
783628 4
26
35
60
110
192
300
428
640
817
Used for horizontal 90˚ junction.
with the junction.
35
X-junction W13/40
WEF-0001
Pre-galvanized
Push-in assembly.
A
mm
X-junction W13/40-70
67
97
197
297
397
497
597
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
1.25
1.25
1.25
1.25
1.25
1.25
1.25
717913 8
717914 5
717915 2
717916 9
717917 6
721188 3
723200 0
729146 5
729147 2
729148 9
729149 6
729150 2
729151 9
729152 6
64
80
150
240
350
480
630
Used for horizontal 90˚ junction of four trays with the same width.
Suspension components should be mounted in or in connection with
the junction.
36
If necessary, the X-junction W13/40 can be locked using Screw set
W38P or Locking plug W41. Can be provided with holes in bottom for
suspension in Pendant attachment W21 or Tube pendant attachment
W73. Valid for max. width 200 mm.
X-junction W13F/40
WEF-0001
Hot dip galvanized
Push-in assembly.
A
mm
X-junction W13F/40-50
47
67
97
147
197
297
397
497
597
L
mm
Plate
thickness
mm
Hot dip galv.
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
148
217
313
434
555
662
762
932
1032
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
783680 2
783681 9
783682 6
783683 3
783684 0
783685 7
783686 4
783687 1
783688 8
783640 6
783641 3
783642 0
783643 7
783644 4
783645 1
783646 8
783647 5
783648 2
27
43
74
147
243
370
510
766
966
Used for horizontal 90˚ junction
of four trays with the same width.
with the junction.
37
WEF-0001
Pre-galvanized
For push-in assembly. Fitted for transition between different widths of Cable trays W1/40 and W3/40 at wall mountings.
Reducing piece W14/40 200-100 left
A
mm
B
mm
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
198
298
398
298
398
398
98
98
98
198
198
298
1.0
1.25
1.25
1.25
1.25
1.25
713620 9
713622 3
713623 0
713631 5
713632 2
713637 7
729159 5
729160 1
729161 8
729162 5
729163 2
729164 9
53
81
96
96
111
126
For transition between different
widths of trays and rails during
wall mounting.
38
If necessary, the Reducing piece
W14/40 can be locked using
W41.
with the reducing piece.
Support bracket/joint W7/40 and
a suitable pendant can be used to
WEF-0001
Hot dip galvanized
E
WIBE
C
A
mm
B
mm
L
mm
Plate
thickness
mm
Hot dip galv.
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
147
197
197
297
297
297
397
397
397
397
497
497
497
497
497
597
597
597
597
597
597
97
97
147
97
147
197
97
147
197
297
97
147
197
297
397
97
147
197
297
397
497
132
182
132
282
222
182
382
332
282
182
482
432
382
282
182
582
532
482
382
282
182
1.25
1.0
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
787796 6
783696 3
787797 3
783697 0
787798 0
783699 4
783698 7
787799 7
783700 7
783701 4
787785 0
787786 7
787787 4
787788 1
787789 8
787790 4
787791 1
787792 8
787793 5
787794 2
787795 9
787811 6
783708 3
787812 3
783709 0
787813 0
783711 3
783710 6
787814 7
783712 0
783713 7
787800 0
787801 7
787802 4
787803 1
787804 8
787805 5
787806 2
787807 9
787808 6
787809 3
787810 9
23
38
30
75
67
56
121
113
102
74
178
170
159
130
92
245
236
226
197
158
101
E
WIBE
C
wall mounting.
39
WEF-0001
Pre-galvanized
Reducing piece W14/40 200-100 right
A
mm
B
mm
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
198
298
398
298
398
398
98
98
98
198
198
298
1.0
1.25
1.25
1.25
1.25
1.25
713536 3
713538 7
713539 4
713547 9
713548 6
713553 0
729165 6
729166 3
729167 0
729168 7
729169 4
729170 0
53
81
96
96
111
126
wall mounting. Push-in installation.
40
Screw set W38P or locking plug
W41.
Support bracket/joint W7/40 and
a suitable pendant can be used to
WEF-0001
Hot dip galvanized
A
mm
B
mm
L
mm
Plate
thickness
mm
Hot dip galv.
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
147
197
197
297
297
297
397
397
397
397
497
497
497
497
497
597
597
597
597
597
597
97
97
147
97
147
197
97
147
197
297
97
147
197
297
397
97
147
197
297
397
497
132
182
132
282
222
182
382
332
282
182
482
432
382
282
182
582
532
482
382
282
182
1.25
1.0
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
787841 3
783690 1
787842 0
783691 8
787843 7
783693 2
783692 5
787844 4
783694 9
783695 6
787830 7
787831 4
787832 1
787833 8
787834 5
787835 2
787836 9
787837 6
787838 3
787839 0
787840 6
787856 7
783714 4
787857 4
783715 1
787858 1
783717 5
783716 8
787859 8
783718 2
783719 9
787845 1
787846 8
787847 5
787848 2
787849 9
787850 5
787851 2
787852 9
787853 6
787854 3
787855 0
23
38
30
75
67
56
121
113
102
74
178
170
159
130
92
245
236
226
197
158
101
wall mounting.
41
WEF-0001
Pre-galvanized
For push-in assembly.
Fitted for transition between different widths of Cable trays W1/40 and W3/40 at symmetric ceiling installation.
Reducing piece W15/40 200-100 straight
A
mm
B
mm
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
198
298
398
298
398
398
98
98
98
198
198
298
1.0
1.25
1.25
1.25
1.25
1.25
713704 6
713706 0
713707 7
713715 2
713716 9
713721 3
729171 7
729172 4
729173 1
729174 8
729175 5
729176 2
53
81
96
96
111
126
tray widths during symmetric
ceiling installation.
Push-in assembly.
42
W41.
with the reducing piece
Support bracket/joint W7/40 and a
suitable pendant can be used to
WEF-0001
Hot dip galvanized
For push-in assembly.
Fitted for transition between different widths of Cable trays W1/40 and W3/40 at symmetric ceiling installation.
A
mm
B
mm
L
mm
Plate
thickness
mm
Hot dip galv.
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
147
197
197
297
297
297
397
397
397
397
497
497
497
497
497
597
597
597
597
597
597
97
97
147
97
147
197
97
147
197
297
97
147
197
297
397
97
147
197
297
397
497
118
154
118
225
190
154
297
261
225
154
368
333
297
225
154
440
404
368
297
225
154
1.25
1.0
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
787751 5
783702 1
787752 2
783703 8
787753 9
783705 2
783704 5
787754 6
783706 9
783707 6
787740 9
787741 6
787742 3
787743 0
787744 7
787745 4
787746 1
787747 8
787748 5
787749 2
787750 8
787766 9
783720 5
787767 6
783721 2
787768 3
783723 6
783722 9
787769 0
783724 3
783725 0
787755 3
787756 0
787757 7
787758 4
787759 1
787760 7
787761 4
787762 1
787763 8
787764 5
787765 2
20
25
26
59
53
46
94
88
81
61
135
129
122
103
76
183
178
171
151
125
91
tray widths during symmetric
ceiling installation.
Push-in assembly.
43
WEF-0001
Junction box plate W24 for installing junction boxes, light fittings etc. in Cable trays W1/40, W3/40 and lighting trunkings.
Unholed
Junction box plate
Plate
thickness
mm
W24/40
1.0
W24/40 unholed
1.0
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
717995 4
730247 5
734617 2
Pre-galv.
White30
Part. No. C*
ZINKPOX®
White80
Part. No. C*
729184 7
734211 2
783130 2
Weight kg
100 pcs
31
31
The Junction box plate W24/40 is
mounted between the bottom of
the trunking or tray and its folded
seam.
44
If necessary, the Junction box
plate W24/40 can be screwed
tight directly in Tray W3/40 with
Screw set W38P. If one requires
a hidden socket box, the junction
box should be folded inwards.
Can be mounted in the middle of
Lighting trunking W70/W71-100
and W70-200 with Screw set
W36 or Tray W3/40 with Screw
set W38P.
To firmly attach Junction box
plate W24/40 in Tray W1/40 or
W3/40, use blind rivets, selftapping screws or Screw set
W38P.
WEF-0001
Used for assembly of light fittings under Cable trays W1/40 and W3/40 or Lighting trunking W70/W71.
Luminaire bracket W25/40-70
A
mm
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
72
101
201
301
401
501
601
1.25
1.25
1.25
1.25
1.25
1.25
1.25
713911 8
713912 5
713914 9
713916 3
713917 0
713918 7
713913 2
729185 4
729186 1
729187 8
729188 5
729189 2
729190 8
729191 5
7
8
11
19
23
27
31
Used for installation of light fittings under tray or trunking.
Can easily be moved along the tray or trunking.
For mounting of light fittings between and under two trays or lighting
trunking. The light fitting is easily moved along the tray or lighting
trunking.
45
Cable tray W1/60, unperforated
WEF-0001
Holes Ø 5.8 mm at the tray ends can be used for locking of joints.
A
mm
Cable tray W1/60-70
70
100
200
300
400
500
600
500
600
L
mm
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 m
2000
2000
2000
2000
2000
2000
2000
2000
2000
1.0
1.0
1.25
1.25
1.25
1.5
1.5
1.5
1.5
781999 7
782000 9
782001 6
723974 0
723975 7
723976 4
723977 1
782046 7
782047 4
782011 5
782012 2
782013 9
782014 6
782015 3
782016 0
782017 7
782048 1
782049 8
165
185
335
440
540
755
870
760
875
46
WEF-0001
Holes Ø 5.8 mm at the tray ends can be used for locking of joints.
Oval holes along the sides can be used for mounting of accessories.
60
A
mm
Cable tray W3/60-70
70
100
150
200
300
400
L
mm
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 m
3000
3000
3000
3000
3000
3000
1.0
1.0
1.0
1.0
1.25
1.25
782202 7
782203 4
782204 1
782205 8
782206 5
782207 2
782306 2
782307 9
782308 6
782309 3
782310 9
782311 6
150
180
200
240
337
440
47
WEF-0001
For installation inside Cable tray W1/60 and W3/60.
W1860 100-200
W1860 300-600
Adjustable
cantilever arm
B
mm
C
mm
D
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
W1860-100
89
160
W1860-200
189
160
W1860-300
289
185
W1860-400
389
185
W1860-500
489
185
W1860-600
589
185
70
70
95
95
95
95
0-25
0-50
0-50
0-50
0-50
0-50
782392 5
782393 2
782394 9
782395 6
782396 3
782397 3
783504 1
783505 8
783506 5
783507 2
783508 9
783509 6
47
65
123
142
161
180
A
mm
Loading table for cantilever arm on wall
Mounted onto wall with Expansion bolt.
mounted onto wall - see below.
Type of
cantilever arm
of cantilever arm
kN
kg
W1860-100
W1860-200
W1860-300
W1860-400
W1860-500
W1860-600
1.0
0.8
1.1
1.0
0.65
0.5
100
80
110
100
65
50
Deflection in mm vid 3˚ deflection
of cantilever arm
5.2
10.5
15.7
20.9
26
31.5
Breaking load
kN
kg
3.0
2.0
3.0
2.0
1.3
1.0
300
200
300
200
130
100
Mounting directly onto wall.
At this type of installation the
adjusting allowance of the tray is
limited.
Breaking load - see table above.
48
Mounting on Vertical piece 2F
using T-bolt. The Cantilever arm
W1860 can be adjusted to a
max. of 50 mm.
Mounting of two adjustable cantilever arms on the same Vertical
piece 2F. (Tray widths more than
400 mm).
Use Screw set 20S if the two
trays have the same width.
At different tray widths T -bolt 26
and Screw set W37 must be
used.
When mounting cable trays widths 500-600 mm - it might be
necessary with a reinforcement
of the cantilever arm. Installation
band and stretching screw can
be used for mounting in ceiling or
on a vertical piece.
WEF-0001
A
A
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
89
189
289
389
489
589
782332 1
782333 8
782334 5
782335 2
782336 9
782337 6
783166 1
783167 8
783168 5
783169 2
783170 8
783171 5
19
37
58
77
96
115
Tray W1/60 and W3/60 with
widths of 200 to 400 are
mounted with suitable Support
bracket W1960 and Pendant rail
W32, Pendant attachment W21
and Screw set W37.
Trays with width 100 can be
mounted with Support bracket
W1960-100, one half of Pendant
attachment W21 or Tube pendant W73 and Screw set W36/
W36C.
with Ceiling bracket 5, Pendant/
Fixing rail 24/34 and Angle
bracket W8S. Screw set 22S
must be used. For cable trays
with width 500 and 600.
on Vertical piece 2 and Ceiling
bracket 5. Screw set 22S must
be used. For cable trays with
width 500 och 600.
Support bracket W1960 can be
mounted with Vertical piece 2,
Pendant joint 2J, Pendant/Fixing
rail 24/34 and Ceiling bracket 5.
Screw set 22S must be used. For
cable trays with width 500 and
600.
2 M10 nuts.
Tube pendant attachment W73.
Pendant rail W32, Pendant
attachment W21 and Screw set
W37.
Tray W1/60 and W3/60 can be
mounted on suitable Support
bracket W1960 and 2 End brackets WN17 as pendant. The end
brackets are joined with 2 Screw
sets 22S and can be adjusted in
height. The pendant can be
mounted in the support bracket
with 1 Screw set W36/W36C.
49
Used as a support bracket or joint for Cable tray W1/60 and W3/60.
When joining Cable tray W1/60 FS (reinforced), Side joint W49/60 must be used.
W7/60-70,150
W7/60-500,600
W7/60-100,200,300,400
Support bracket/joint W7/60-70
Joint W7/60-500
Joint W7/60-600
WEF-0001
A
mm
B
mm
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
68
98
148
198
297
397
498
598
152
200
200
200
300
300
300
300
1.0
1.0
1.0
1.0
1.25
1.25
1.25
1.25
782209 6
718445 3
782210 2
718446 0
718447 7
718448 4
782211 9
782212 6
782318 5
782319 2
782320 8
782321 5
782322 2
782323 9
782324 6
782325 3
22
33
41
49
122
152
180
210
used for straight joining. Push-in
mounting.
If necessary trays are locked
using Screw set W38P or
Locking plug W41.
With Pendant attachment W21
installed, a complete support
bracket is obtained. Does not
apply to W7/60-70,150,500 and
600.
W7/60-500 och 600 are only
used for joining, not as support
brackets.
Reinforced tray is to be joined
with Side joint W49/60.
End bracket WN17 can be used
as vertical piece on Support
bracket/joint W7/60 mounted
used to achieve an invisible
suspension in or in connection
with bends or junctions, here with
End bracket WN17 mounted as
vertical piece.
50
or the one half of Pendant
attachment W21 are mounted
with Screw set W36/W36C.Does
not apply to W7/60-500 and 600.
Side joint W49/60
WEF-0001
For straight joining of Cable tray W1/60 and W3/60.
Side joint W49/60
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
782267 6
782330 7
27
2 Side joints W49/60 are used for
straight joining of Cable tray W1/60,
W1/60 FS and W3/60.
4 Screw sets W38P are required
(not included).
Reducer W28/60
WEF-0001
Used for transition joining of Cable trays W1/60 or W3/60.
Reducer W28/60-100
Reducer W28/60-200
A
mm
B
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
100
200
57.5
57.5
787442 2
787443 9
787444 6
787445 3
27
36
Used together with 1 Side joint
W49/60 at one-side transition
joining of Cable trays W1/60 and
W3/60, to be mounted with
2 Screw sets W38P. Always use
support close to the reducer.
2 Reducers W28/60 are used at
centered transition joining, to be
mounted with Screw set W38P.
Always use support close to the
reducer.
51
T-joint W9/60
WEF-0001
Used for straight or oblique branches of Cable trays W1/60 or W3/60.
T-joint W9/60 (Screw set W38P incl.)
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. NoC*
Weight kg
100 pcs
1.25
782217 1
782218 8
5
1
2
Potential balancing
balancing according to
SS-EN 61537 the T-joint must be
secured with
RXB 4.2x13
2 Screw set W38P,
drilling is required
Tightening torque 2 Nm
52
T-joint W9/60 is mounted on the
sides of the tray with Screw set
W38P.
Straight branches.
If necessary, the lugs are locked
to the edge of the tray using
pliers. Can also be locked with
blind rivets or self-tapping
screws.
Oblique branches.
If necessary, the lugs are locked
to the edge of the tray using
pliers. Can also be locked with
blind rivets or self-tapping
screws.
T-joint W29/60
WEF-0001
Simple push-in assembly. Locks into tray via locking flap.
Is hung over the edge of the tray and locked in a suitable way.
T-joint W29/60-70
T-joint W29/60-100
T-joint W29/60-200
T-joint W29/60-300
T-joint W29/60-400
T-joint W29/60-500
T-joint W29/60-600
A
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
68
98
198
298
398
498
598
783178 4
783179 1
783180 7
783181 4
783182 1
783183 8
783184 5
783185 2
783186 9
783187 6
783188 3
783189 0
783190 6
783191 3
22
27
37
47
57
67
77
Potential balancing
balancing according to
SS-EN 61537 the T-joint must be
secured with
RXB 4.2x13
2 Screw set W38P,
drilling is required
Tightening torque 2 Nm
Used with T- and X-junction.
Mounted directly onto tray edge.
Can be attached to tray by
pinching the lip at the top of the
tray.
53
WEF-0001
For horizontal angling of Cable ladders W1/60 or W3/60.
A
mm
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No C*
Weight kg
100 pcs
67
97
147
197
297
397
497
597
1.0
1.0
1.0
1.0
1.0
1.0
1.25
1.25
782268 3
782269 0
782270 6
782271 3
782272 0
782273 7
782274 4
782275 1
782471 7
782472 4
782473 1
782474 8
782475 5
782476 2
782477 9
782478 6
17
23
37
53
97
156
292
406
V
Push-in installation. Turn up
inner and outer sides and mount
the Adjustable bend W10/60
inside the tray.
54
Adjustable bend W10/60 permits
desired horizontal angling
between 105˚ and 165˚ in stages
of 7.5˚.
If necessary, Adjustable bend
W10/60 may be locked using
W41.
WEF-0001
For upward or downward branching of Cable trays W1/60 or W3/60 to desired angle.
Push-in assembly.
A
mm
L
mm
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
Vertical riser W11/60-70
67
97
147
197
297
397
497
597
150
150
150
200
200
200
200
200
0.7
0.7
0.7
0.7
0.7
0.7
0.7
0.7
782276 8
782277 5
782278 2
782279 9
782280 5
782281 2
782282 9
782283 6
782593 6
782594 3
782595 0
782596 7
782597 4
782598 1
782599 8
782600 1
12
15
19
31
42
53
64
75
Vertical riser W11/60 is delivered
flat and must be bent by the
installer on the job site.
For upward or downward
branching at a desired angle up
to 90˚. Push-in installation.
Should be attached with Screw
55
90˚ bend W10/60
WEF-0001
For 90˚ horizontal angling of Cable trays W1/60 or W3/60.
Push-in assembly.
A
mm
B
mm
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
90˚ bend W10/60-70
67
90˚ bend W10/60-100
97
90˚ bend W10/60-150
147
90˚ bend W10/60-200
197
90˚ bend W10/60-300
297
90˚ bend W10/60-400
397
90˚ bend W10/60-500
497
90˚ bend W10/60-600
597
90˚ bend W10/60-500 FS
497
90˚ bend W10/60-600 FS
597
167
197
247
297
397
497
597
697
597
697
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
782038 2
782039 9
782040 5
782041 2
782042 9
782043 6
782044 3
782045 0
782458 8
782459 5
782408 3
782409 0
782410 6
782411 3
782412 0
782413 7
782414 4
782415 1
787188 9
787189 6
43
55
85
117
196
295
413
551
343
465
with the bend.
56
If necessary, the 90˚ bend
W1060 can be locked using
Screw set W38P or Locking
plug W41. Can be provided with
holes in bottom for suspension
in Pendant attachment W21
alternatively W73.
T-junction W12/60
WEF-0001
For 90˚ horizontal junction of Cable trays W1/60 or W3/60.
Push-in assembly.
T-junction W12/60-500 FS
T-junction W12/60-600 FS
A
mm
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
67
97
147
197
297
397
497
597
497
597
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
782052 8
782053 5
782054 2
782055 9
782056 6
782057 3
782058 0
782059 7
782460 1
782461 8
782424 3
782425 0
782426 7
782427 4
782428 1
782429 8
782430 4
782431 1
787192 6
787193 3
54
70
99
133
217
320
443
585
337
454
Used for 90˚ horizontal junction.
with the junction.
If necessary, the junction can be
locked using Screw set W38P
or Locking plug W41. Can be
provided with holes in bottom for
suspension in Pendant attachment W21 alternatively W73.
57
X-junction W13/60
WEF-0001
For 90˚ horizontal junction of Cable trays W1/60 or W3/60.
Push-in assembly.
A
mm
B
mm
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
67
97
147
197
297
397
497
597
X-junction W13/60-500 FS
497
X-junction W13/60-600 FS
597
268
298
348
398
498
598
698
798
698
798
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
1.25
782095 5
782096 2
782097 9
782098 6
782099 3
782100 6
782101 3
782102 0
782462 5
782463 2
782440 3
782441 0
782442 7
782443 4
782444 1
782445 8
782446 5
782447 2
787196 4
787197 1
62
78
110
146
234
342
469
616
328
441
Used for 90˚ horizontal junction
of four trays with the same width.
with the junction.
58
If necessary, the junction can be
locked using Screw set W38P
or Locking plug W41. Can be
provided with holes in bottom for
suspension in Pendant attachment W21 alternatively W73.
WEF-0001
Push-in assembly fitted for transition between different widths of Cable trays W1/60 or W3/60.
A
mm
B
mm
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
197
297
397
297
397
397
97
97
97
197
197
297
1.25
1.25
1.25
1.25
1.25
1.25
782163 1
782164 8
782165 5
782166 2
782167 9
782168 6
782517 2
782518 9
782519 6
782520 2
782521 9
782522 6
89
139
198
123
183
158
Used for transition between
different widths of trays during
wall mounting.
W41.
Support bracket/joint W7/60,
mounted with a suitable pendant,
is used to achieve an invisible
suspension, here with End
bracket WN17 mounted as
vertical piece.
59
WEF-0001
Push-in assembly fitted for transition between different widths
of Cable trays W1/60 or W3/60.
A
mm
B
mm
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
197
297
397
297
397
397
97
97
97
197
197
297
1.25
1.25
1.25
1.25
1.25
1.25
782153 2
782154 9
782155 6
782156 3
782157 0
782158 7
782505 9
782506 6
782507 3
782508 0
782509 7
782510 3
89
139
198
123
183
158
different widths of trays during
wall mounting.
60
W41.
vertical piece.
WEF-0001
Push-in assembly fitted for transition between different widths of Cable trays W1/60 or W3/60.
A
mm
B
mm
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
197
297
397
297
397
397
97
97
97
197
197
297
1.25
1.25
1.25
1.25
1.25
1.25
782104 4
782105 1
782106 8
782107 5
782108 2
782109 9
782491 5
782492 2
782493 9
782494 6
782495 3
782496 0
76
122
179
105
162
134
different tray widths during
symmetric ceiling installation.
Push-in assembly.
W41.
vertical piece.
61
End cover W45/60
WEF-0001
Push-in assembly mounted as end cover in Cable trays W1/60 or W3/60.
A
mm
End cover W45/60-70
68
98
198
298
398
498
598
Mounted as end cover in cable
trays. Locked with Screw set
W38P or Locking plug W41.
62
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
1.0
1.0
1.0
1.0
1.0
1.0
1.0
782292 8
782293 5
782294 2
782295 9
782296 6
782297 3
782298 0
786771 4
786772 1
786773 8
786774 5
786775 2
786776 9
786777 6
12
13
18
23
28
34
39
WEF-0001
Used for installing junction boxes, light fittings etc. in Cable
trays W1/60 or W3/60.
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
1.0
718193 3
782659 9
34
The Junction box plate W24/60 is
mounted between the bottom of
the tray and its folded seam.
If necessary, the Junction box
plate W24/60 can be tightened
directly in Tray W3/60 with Screw
set W38P. If one requires a
hidden socket box, the junction
box should be folded inwards.
Can be mounted in the middle
of Tray W3/60 with Screw set
W38P.
To firmly attach Junction box
plate W24/60 in Tray W1/60
or W3/60, use blind rivets, selftapping screws or Screw set
W38P.
63
WEF-0001
Mounted to divide Cable trays W1/60 or W3/60.
*EAN-code=732167+Part.nr+C (control figure)
Plate
thickness
mm
H
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
0.6
55
725785 0
782787 9
73
Used to separate tray in two or
more ducts, thereby separating
control cables from other cables
and pipes. The hole structure at
distances of 250 mm permits two
fixing opportunities with Support
band W6 even after cutting.
Support band W6
WEF-0001
The Support band W6 is mounted to fix the lateral position of one or several Dividing strips 39/55.
Support band W6-70
Support band W6-100
Support band W6-200
Support band W6-300
Support band W6-400
Support band W6-500
Support band W6-600
L
mm
Pre-galv.
Part. No. C*
Weight kg
100 pcs
67
97
197
297
397
497
597
718828 4
718829 1
718830 7
718831 4
718832 1
718833 8
718834 5
1.0
1.4
2.8
4.3
5.7
7.2
8.6
Support band W6 is mounted to
fix one or more Dividing strips 39
laterally. The holes in the support
band and the locking pins in
Dividing strip 39 allow for a fixed
division with intervals of 25 mm.
64
Insert piece W39/55
WEF-0001
Insert piece W39/55 is used to join Dividing strips 39/55.
Insert piece W39/55
Pre-galv.
Part. No. C*
Pre-galv. White30
Part. No. C*
Weight kg
100 pcs
782299 7
786873 5
19
Insert piece W39/55 is used to
join Dividing strips 39/55 and is
mounted on Support bracket/joint
W7/60.
Used for assembly of light fittings under Cable trays W1/60 and W3/60.
WEF-0001
A
mm
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
72
101
201
301
401
501
601
1.25
1.25
1.25
1.25
1.25
1.25
1.25
782284 3
782285 0
782286 7
782287 4
782288 1
782289 8
782290 4
782614 8
782615 5
782616 2
782617 9
782618 6
782619 3
782620 9
7.7
8.6
14
18
23
27
32
The luminaire bracket can easily
be moved along the tray.
For mounting of lighting fittings
under Cable tray W1/60 and
W3/60.
65
Cover strip W47/60
WEF-0001
Used for covering space between joined Cable trays W1/60 or W3/60.
B
mm
Cover strip W47/60-70
71.5
101.5
202
302
402
502.5
602.5
Cover strip W47/60 is mounted
to cover the space that might
occur when joining cable trays.
66
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
1.0
1.0
1.0
1.0
1.0
1.0
1.0
786799 8
786800 1
786801 8
786802 5
786803 2
786804 9
786805 6
786806 3
786807 0
786808 7
786809 4
786810 0
786811 7
786812 4
8
9
12
15
18
21
24
67
WEF-0001
Use Support bracket W7/40 for joining.
A
mm
B
mm
C
mm
D
mm
t
mm
L
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 m
40
70
100
200
22
40
40
40
10.5
8.5
8.5
8.5
6
5
5
5
1.5
1
1
1
2995
3000
3000
3000
720980 4
720792 3
720793 0
720794 7
729023 9
729024 6
729025 3
729026 0
107
125
147
220
A
mm
B
mm
C
mm
D
mm
t
mm
L
mm
Hot dip galv.
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 m
Lighting trunking W70-40
40
22
70
40
100 40
200 40
10.5
8.5
8.5
8.5
6
5
5
5
1.5
1
1
1
2995
3000
3000
3000
790067 1
790068 8
790069 5
790079 1
790071 8
790072 5
790073 2
790074 9
113
133
157
237
Load capacity
Downward deflection refers to outer compartment
Downward deflection refers to middle compartment
K = Bracket distance
Load kg
W70/70-200
A
25
50
30
60
20
40
B
C
D
68
Installation method K = 1.5 m
Deflection mm
W70-40
W70/70-200
W70-40
20
40
20
40
20
40
Installation method K = 3 m suspended in joints
Load kg
Deflection mm
W70/70-200
W70-40
W70/70-200
W70-40
1.5
2
25
10
3.5
4.5
50
20
1
2.5
30
10
2.5
5
60
20
2
3
20
10
4
6.5
40
20
Breaking load for Support bracket/joint W7/40-70 = 120 kg
15
30
7
14
13
26
15
31
4
8
19
38
WEF-0001
Use Support bracket W7/40 for joining.
A
mm
70
100
B
mm
C
mm
D
mm
t
mm
L
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 m
40
40
8.5
8.5
6
6
1
1
6000
6000
734511 3
734512 0
734513 7
734514 4
130
153
Load capacity
Downward deflection refers to outer compartment
Downward deflection refers to middle compartment
K = Bracket distance
Installation method K = 1.5 m
Load kg
Deflection mm
W71/70-100
W71/70-100
A
B
C
D
25
50
30
60
20
40
Installation method K = 3 m suspended in joints
Load kg
Deflection mm
W71/70-100
W71/70-100
1.5
25
3.5
50
1
30
2.5
60
2
20
4
40
Breaking load for Support bracket/Joint W7/40-70 = 120 kg
15
30
7
14
13
26
69
Support bracket W20
WEF-0001
For invisible installation of Lighting trunking W70/71, width 70 and 100 mm.
The support bracket is snapped firmly into the trunking. Threaded rod M10 W76 is used.
W20-100
W20-70
Pre-galv.
Part. No. C*
Weight kg
100 pcs
720973 6
721943 8
9
13
Support bracket W20-70 (2 nuts M10 are included)
Support bracket W20-100 (2 nuts M10 are included)
Support bracket W20-70 is
mounted with Threaded rod M10
W76 and 2 M10 nuts.
Lightly press down Support bracket W20-70 into Lighting trunking
W70/W71-70.
Support bracket W20-100 is
mounted with Threaded rod M10
W76 with 2 M10 nuts.
WEF-0001
For invisible installing of Lighting trunking W70/W71, width 70 and 100 mm. Threaded rod M10 W76 is used.
The support bracket’s spring locking device facilitates easy vertical adjustment.
W20A-100
W20A-70
*EAN-code=732167+Part. No.+C (control figure)
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
720970 5
721180 7
729027 7
729028 4
15
20
Support brackets W20A-70 and
W20A-100 are mounted on
Threaded rod M10 W76. This
enables simple vertical adjustment of ±30 mm.
70
Lightly press down Support bracket W20A-70 into Lighting trunking
W70/W71-70.
is easily snapped firmly into
Lighting trunking W70/W71-100.
Pendant brackets W80 and W81
WEF-0001
Used together with Lighting trunking W70-40.
Pendant bracket W80
Pendant bracket W81
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
718474 3
718477 4
729056 7
729057 4
9
8
(Only for Lighting trunking W70-40)
Pendant bracket W80 mounted
under Lighting trunking W70-40
and attached with Screw set
W36/W36C. Threaded rod M10
W76 is easily mounted in the
spring clasp without bolts.
Adjustable to ±30 mm.
Pendant bracket W81 is
mounted under Lighting trunking
W70-40 and is attached with
Screw set W36/W36C. Pendant
rail W32 is mounted using Screw
set W37. Adjustable to ±18 mm.
WEF-0001
For mounting of strip lighting centred under Lighting trunking W70/W71.
Use Screw set W36/W36C or W34.
Plate
thickness
mm
Pre-galv.
Part. No. C*
Weight kg
100 pcs
1.5
715650 4
3
Mounted in the rail’s module
holes with Screw set W36/W36C
or W34.
Note! The fork openings must be
mounted in the same direction.
71
WEF-0001
Used for mounting of light fittings under Lighting trunking W70.
Electro-galv.
Part. No. C*
Weight kg
100 pcs
720979 8
0.8
Mounted in the mounting holes in
Lighting trunking W70.
Always mount the Luminaire
bracket W55 from above so that
it rests in the tray.
WEF-0001
Used for installation of light fittings in Lighting trunking W71.
Luminaire bracket W56 (screw MSCS6x12)
Always mount the Luminaire
bracket W56 from above so that
it rests in the tray.
72
Aluminium
Part. No. C*
Weight kg
100 pcs
734565 6
1
73
Installation tray W4,
outline of assembly
Components
1. Cantilever arm 50
2. Installation tray W4
3. Joint W2
4. 90˚ bend W4
5. Vertical riser W4, interior
6. Vertical riser W4, exterior
7. Angle bracket W8
8. Screw set W38P
9. Screw set W34
74
WEF-0001
Wibe installation trays W4 are perforated with a hole structure suitable for the majority of clamping methods.
Suitable even for vertical wall mounting in industries, in lifts and fan rooms.
Holes Ø 3.5 mm in the tray bottom allow clamping of cables with plate screws.
The tray can also be used for horizontal mounting on cantilever arms.
Maximum bracket distance 1.5 m. Joints are to be mounted on the cantilever.
A varity of colours can be offered.
t
mm
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 m
Installation tray W4-50
3000 50 1.0
3000 75 1.0
3000 100 1.0
3000 150 1.0
3000 200 1.25
3000 250 1.25
1960 300 1.25
1960 400 1.25
735988 2
735989 9
735990 5
735991 2
735992 9
735993 6
736609 5
736610 1
735977 6
735978 3
735979 0
735980 6
735981 3
735982 0
736619 4
736620 0
787227 5
787228 2
787229 9
787230 5
787231 2
787232 9
736639 2
736640 8
735999 8
736000 0
736001 7
736002 4
736003 1
736004 8
736005 5
736006 2
57
76
93
125
195
228
238
313
L
mm
A
mm
Suitable for leading cables down
from a cable ladder to machine
cabinet etc.
75
Joint W2
WEF-0001
For joining of Installation tray W4.
Plate
thickness
mm
Pre-galv.
Part. No. C*
Joint W2
1.25
788572 5
Used for joining Tray W4. To be
mounted on the outside of the
tray and attached in bottom with
2 Screw sets W34/W38P.
76
Hot dip galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
788573 2
788574 9
788575 8
8
90˚ bend W4
WEF-0001
For horizontal 90˚ angling of Installation tray W4.
A
mm
90˚ bend W4-50
52
90˚ bend W4-75
77
90˚ bend W4-100
102
90˚ bend W4-150
152
90˚ bend W4-200
202
90˚ bend W4-250
252
90˚ bend W4-300
302
90˚ bend W4-400
402
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
724848 3
724849 0
724850 6
724851 3
724852 0
724853 7
724854 4
724855 1
724981 7
724982 4
724983 1
724984 8
724985 5
724986 2
724987 9
724988 6
729095 6
729096 3
729097 0
729098 7
729099 4
729100 7
729101 4
729102 1
782930 9
782931 6
782932 3
782933 0
782934 7
782935 4
782936 1
782937 8
12
19
26
44
66
92
121
192
Used for horizontal 90˚ angling.
Mounted outside of W4 trays.
Attached in bottom with Screw
set W34 (pre-galvanized and
powder coated trays).
In hot dip galvanized trays Screw
set W38P must be used.
77
Vertical riser W4, interior
WEF-0001
For vertical 90˚ angling of Installation tray W4.
A
mm
Vertical riser W4-50, interior
52
77
102
152
202
252
302
402
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
724840 7
724841 4
724842 1
724843 8
724844 5
724845 2
724846 9
724847 6
724934 3
734935 0
734936 7
724937 4
727938 1
724939 8
724940 4
724941 1
729110 6
729111 3
729112 0
729113 7
729114 4
729115 1
729116 8
729117 5
782950 7
782951 4
782952 1
782953 8
782954 5
782955 2
782956 9
782957 6
18
24
30
41
53
65
76
99
Used for vertical 90˚ angling.
Mounted outside of trays W4.
powder coated trays).
In hot dip galvanized trays Screw
set W38P must be used.
78
Used for vertical 90˚ angling from
cable ladder. Attached to cable
ladders with strips.
Vertical riser W4, exterior
WEF-0001
For vertical 90˚ angling of Installation tray W4.
A
mm
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
Vertical riser W4-50, exterior
52
77
102
152
202
252
302
402
724832 2
724833 9
724834 6
724835 3
724836 0
724837 7
724838 4
724839 1
724926 8
724927 5
724928 2
724929 9
724930 5
724931 2
724932 9
724933 6
729118 2
729119 9
729120 5
729121 2
729122 9
729123 6
729124 3
729125 0
782970 5
782971 2
782972 9
782973 6
782974 3
782975 0
782976 7
782977 4
18
24
30
41
53
65
76
99
Used for vertical 90˚ angling.
Mounted outside of Trays W4.
powder coated trays). In hot dip
galvanized trays Screw set
W38P must be used.
Used for vertical 90˚ angling from
cable ladder. Attached to cable
ladders with strips.
79
Cantilever arm 50
WEF-0001
For mounting on walls, pendant/fixing rails or vertical pieces.
50L,50/100-300 50L,50/400-600 50L,50/700-1000
A
mm
Cantilever arm 50L-100
150
200
250
298
348
447
548
646
Cantilever arm 50-100
150
200
250
300
350
450
550
650
750
850
950
1050
80
F
mm
H
mm
T
mm
Hot dip galv.
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
34
36
39
56
60
70
77
84
34
36
39
56
60
70
77
84
90
95
100
105
85
85
85
105
105
120
140
150
85
85
85
105
105
120
140
150
150
160
160
170
4
4
4
4
4
5
6
6
4
4
4
6
6
8
8
10
10
10
10
10
725105 6
725106 3
725107 0
725108 7
725109 4
725110 0
725111 7
725112 4
723432 5
723433 2
723434 9
723435 6
723436 3
723437 0
723438 7
723439 4
727125 2
727126 9
727127 6
727128 3
725113 1
725114 8
725115 5
725116 2
725117 9
725118 6
725119 3
725120 9
723440 0
723441 7
723442 4
723443 1
723444 8
723445 5
723446 2
723447 9
727782 7
727783 4
727784 1
727785 8
24
28
34
46
54
103
160
191
24
28
34
52
60
118
172
215
270
310
350
390
Cantilever arm 50
F
F
Installation of a Cantilever arm
50 to a wall using an Expansion
bolt.
Breaking load F, see table below.
Installation of a Cantilever arm
50 using a T-bolt on pendant/
fixing rails mounted on the wall.
F
Installation of Cantilever arm 50
using T-bolt with vertical pieces.
Also check the breaking load of
vertical pieces.
Breaking load F
F
Type of
cantilever arm
50L-100
50L-150
50L-200
50L-250
50L-300
50L-400
50L-500
50L-600
50-100
50-150
50-200
50-250
50-300
50-400
50-500
50-600
50-700
50-800
50-900
50-1000
Mounted on wall
kN
kg
1.5
150
1.5
150
1.5
150
2.0
200
2.0
200
3.0
300
3.0
300
3.0
300
3.0
300
3.0
300
2.5
250
4.0
400
4.0
400
6.5
650
7.0
700
7.0
700
6.0
600
5.5
550
5.3
530
5.0
500
Mounted on P/F rail 24/48
with T-bolt 26F
kN
kg
1.5
150
1.5
150
1.5
150
2.0
200
2.0
200
3.0
300
3.0
300
3.0
300
3.0
300
3.0
300
2.5
250
4.0
400
4.0
400
6.5
650
7.0
700
7.0
700
5.5
550
5.2
520
4.8
480
4.2
420
81
Cantilever arm 80
WEF-0001
For installation of Cable trays W1 and W3.
The cantilever arm can be mounted on Vertical piece 7/7L or Wall bracket 80.
(Screw set 22S not included)
L
mm
H
mm
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
Weight kg
100 pcs
155
70
730448 6
205
71
730449 3
255
70
730450 9
305
70
730451 6
355
70
730452 3
455
80
730453 0
555
90
730454 7
655
100
730455 4
* EAN-code=732167+Part.no+( (control figure) **Produced to order
732124 7**
732125 4**
732126 1**
732127 8**
732128 5**
732129 2**
732130 8**
732131 5**
12
16
20
28
35
50
65
110
Cantilever arm 80 mounted on
Vertical piece 7/7L with Screw
set 22S. Infinitely adjustable
along the vertical piece. Breaking
load see loading table below.
Cantilever arm 80 can also be
mounted on both sides of Vertical
piece 7 at the same level.
When mounting Cantilever arm
80 on wall, Wall bracket 80 shall
be used together with Screw set
22S.
Breaking load see loading table
below.
Breaking load F
Type of
Cantilever arm
80-100
80-150
80-200
80-250
80-300
80-400
80-500
80-600
82
Mounted on
Wall bracket 80
kN
kg
2.5
250
2.3
230
2.2
220
2.0
200
1.9
190
1.7
170
1.7
170
1.7
170
Mounted at the end of
Vertical piece 7/7L
kN
kg
2.5
250
2.5
250
2.5
250
2.0
200
2.2
220
1.9
190
1.9
190
1.9
190
Mounted along
the Vertical piece 7/7L
kN
kg
2.3
230
2.3
230
2.3
230
2.0
200
2.0
200
1.8
180
1.8
180
1.6
160
Wall bracket 80
For installation of Cantilever arm 80 on wall.
Fits all widths. (Screw set 22S not included.)
WEF-0001
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
Weight kg
100 pcs
Wall bracket 80
729216 5
* EAN-code=732167+Part.no+C (control figure) **Produced to order
733209 0**
23
Wall bracket 80 shall be
mounted with Screw set 22S.
Breaking load see loading table
for Cantilever arm 80.
Back plate W30
For installation behind internal cantilever arms to reduce the
surface pressure on porous walls.
WEF-0001
t
mm
Pre-galv.
Part. No. C *
Pre-galv.
White30
Part. No. C *
Weight kg
100 pcs
Back plate W30
3.0
786792 9
786793 6
42
Mount Back plate W30 as shown
in the illustration to reduce the
surface stress on porous walls.
83
Mounting rail 40
Mounting rail 40 is installed between a cantilever arm and wall to reduce surface
pressure on porous walls or to enable height adjustment of cantilever arms.
Mounting rail 40
WEF-0001
Hot dip galv.
Part. No. C*
ZINKPOX®
White30
Part. No. C*
ZINKPOX®
White80
Part. No C*
Weight kg
100 pcs
717001 2
729045 1
717006 7
56
The mounting rail is installed
between a cantilever arm and
wall to reduce surface pressure
on porous walls or to enable
vertical adjustment of cantilever
arms.
Cantilever arm 50 is installed
using a T-bolt.
The arm is adjustable vertically.
Internal cantilever arm W17 and
are mounted with T-bolt.
The cantilever arm is vertically
adjustable.
Mounting rail WMS25
WEF-0001
Mounting rail WMS 25
Mounting of cables with lashing
wire, strips etc.
84
The mounting rail is installed
directly onto wall.
Hot dip galv.
Part. No. C*
Weight kg
100 pcs
725000 4
147
Threaded rod M8 and M10 W76
WEF-0001
Used for installations of cable trays and lighting trunkings.
Joint nut M8 and M10 are used for joining of Threaded rods M8 and M10 W76.
L
mm
Threaded rod M8
500
Threaded rod M8
1000
Threaded rod M10 W76-2000
2000
Threaded rod M10 W76-3000
3000
Joint nut M8
Joint nut M10
Electro-galv.
Part. No. C*
Stainl. steel
(AISI316)
Part. No. C*
725077 6
725079 0
716792 0
716793 7
725083 7
724806 3
725078 3
725080 6
723925 2
723926 9
725084 4
724807 0
Electro-galv.
White30
Part. No. C*
729061 1
729062 8
Electro-galv.
White80
Part. No. C*
Weight kg
100 pcs
718795 9
718797 3
16
32
100
150
5
7.2
Nut M8 and M10 are used with Threaded rod M8 and M10 W76.
Nut M8
Nut M10
Hot dip galv.
Part. No. C*
Stainl. steel
(AISI316)
Part. No. C*
Weight kg
100 pcs
725085 1
723938 2
725086 8
723939 9
0.54
1.1
Use Joint nut M8 or M10 when
joining 2 pieces of Threaded rods
M8 or M10 W76.
The Threaded rod M10 W76 is
cut to required length and
mounted with 2 Tube pendant
attachments W73.
Installation of Threaded rod M8
or M10 W76 with Concrete screw
MMS-I.
85
WEF-0001
Mounted in Support bracket/joint W7 etc.
Plate
thickness
mm
2
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
716630 5
734618 9
729054 3
783107 4
12
The Pendant attachment W21
is inserted into the slits in the
Support bracket/joint W7 (100400). Does not apply to W7-50,
150, 500 and 600.
The required length of Pendant
rail W32 is mounted in the
Pendant attachment W21 with
Screw set W37.
Adjustable to ±30 mm.
For lighter installations with
small loads, only one half of the
Pendant attachment W21 is
mounted in Support bracket W7
The second part of the Pendant
attachment W21 is used as a
ceiling bracket. The Pendant rail
W32 is mounted using Screw set
W37.
When mounting with wire, only
one half of the Pendant attachment W21 is mounted in Support
bracket/joint W7 using Screw set
W36/W36C. The wire is mounted
through the oval hole and locked
with a wire lock.
When mounting cable tray or
Lighting trunking W70/W71, one
half of Pendant attachment W21
is mounted directly in Support
bracket/joint W7 with Screw set
W36/W36C. Pendant rail W32 is
mounted with Screw set W37.
In concrete ceilings Pendant
attachment W21 is mounted with
Expansion bolt.
In metal plate ceilings, Pendant
attachment W21 is mounted with
Ogebe fixing type ED. Use
Screw set W36/W36C.
1. Pendant attachment W21
2. Screw set W36/W36C
3. Support bracket/joint W7
4. Cable tray/Lighting trunking
Ceiling installation with cable tray/lighting trunking
W7 = Support bracket/joint
W21 = Pendant attachment
W31 = Ceiling attachment
W32 = Pendant rail
W36 = Screw set
W37 = Screw set
W73 = Tube pendant attachment
W76 = Pendant bolt M10
86
WEF-0001
Used for mounting of Pendant bolt M10 W76 in ceilings and trays.
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
734621 9
729055 0
783117 3
7
716634 3
The Tube pendant attachment
W73 is mounted in Support
bracket/joint W7 with Screw set
W36/W36C. Does not apply to
W7-500 and 600.
The Tube pendant attachment
can also be mounted directly in
the lighting trunking using Screw
set W36/W36C. Does not apply
to Lighting trunking W70-40,
where Pendant bracket W80
must be used.
Pendant bolt M10 W76 is easily Mounted in wood with self-drilling
mounted in the spring clasp with- screws.
out screws. Simple adjustment
up to ±30 mm.
Mounted in concrete ceilings with
Expansion bolt.
87
Pendant/Fixing rail 7L, 7
Used with Ceiling bracket 7 to form vertical pieces on site. End plug 7 must be used in Pendant/Fixing rail 7.
Pendant/Fixing rail 7L
Pendant/Fixing rail 7
WEF-0001
7L
7
L
mm
Pendant/Fixing rail 7L
3020
Pendant/Fixing rail 7
3020
* EAN-code=732167+part.no+C (control figure)
Pre-galvanized
Part. No. C*
Hot dip galv.
Part. No. C*
Weight kg
100 pcs
734206 8
735432 0
734205 1
360
370
Using Ceiling bracket 7 together
with Pendant/Fixing rail 7L/7
makes it possible to produce
vertical pieces in different lengths
on site. Use 2 Screw sets 22S.
Cantilever arm 80 is infinitely
adjustable along Pendant/Fixing
rail 7L/7. Screw set 22S shall be
used when mounting.
End plug 7 must be used on
Pendant/Fixing rail 7.
mounted on both sides of the
Pendant/Fixing rail 7 at the same
level (not 7L).
Breaking load for symmetrical
loading 2500 kg (25 kN).
Ceiling bracket 7
To be used with Pendant/Fixing rail 7/7L to form vertical pieces on site.
WEF-0001
11 x 18
Ceiling bracket 7
* EAN-code=732167+Part.no+C (control figure)
Plate thickness
mm
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
Weight kg
100 pcs
2.5
734331 7
734458 1
40
Using Ceiling bracket 7 together
with Pendant/Fixing rail 7/7L
makes it possible to produce
vertical pieces in different lengths
on site. Use 2 Screw sets 22S.
88
WEF-0001
To be used together with Cantilever arm 80. The Cantilever arm is infinitely adjustable along the Vertical piece.
End plug 7 is mounted on Vertical piece 7 on delivery.
Vertical piece 7L
Vertical piece 7
L
mm
Hot dip galv.
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
218
290
398
506
614
722
794
902
1010
1118
1190
735207 4
735208 1
735209 8
735210 4
735211 1
735212 8
735213 5
735214 2
735215 9
735216 6
735217 3
780417 7**
780418 4**
780419 1**
780420 7**
780421 4**
780422 1**
780423 8**
780424 5**
780425 2**
780426 9**
780427 6**
46
56
69
83
98
111
120
135
148
162
171
Vertical piece 7-200
216
731871 1
288
731872 8
396
731873 5
504
731874 2
612
731875 9
720
731876 6
792
731877 3
900
731878 0
1008
731879 7
1116
731880 3
1188
731881 0
1296
731882 7
1404
731883 4
1512
731884 1
1620
731885 8
738487 7**
738488 4**
738489 1**
738490 7**
738491 4**
738492 1**
738493 8**
738494 5**
738495 2**
738496 9**
738497 6**
738498 3**
738499 0**
738500 3**
738501 0**
60
70
80
100
110
120
130
150
170
180
190
200
220
230
250
Vertical piece 7L-200
89
WEF-0001
Loading tables for Vertical piece 7L and 7
Vertical piece 7L
Vertical piece 7
The bending moment M is the total sum of
F x A in kgcm.
F = Force on cantilever arms in kg
F = Loading (kg/m) x Support distance (m)
A = Distance between force and centerline
vertical piece in cm
A = Width of ladder + 1.75 cm
2
The bending moment M is the total sum of
F x A in kgcm.
F = Force on cantilever arms in kg
F = Loading (kg/m) x Support distance (m)
A = Distance between force and centerline
vertical piece in cm
A = Width of ladder + 3.5 cm
2
adjustable along Vertical piece
7L. Screw set 22S must be used
when mounting. The cantilever
arm must always be mounted in
the same direction as the ceiling
bracket.
adjustable along Vertical piece 7.
Screw set 22S must be used
when mounting. End plug 7 must
be used on Vertical piece 7.
mounted on both sides of the
Vertical piece 7 at the same level
(not 7L).
Breaking load for symmetrical
loading 2500 kg (25 kN).
End plug 7
For Vertical piece 7 or Pendant/Fixing rail 7.
End plug 7
Use and installations
End plug 7 must always be used
at the cut end of Vertical piece 7
or Pendant/-Fixing rail 7.
90
WEF-0014
Polyamide (PA) Red
Part. No. C*
Weight kg
100 pcs
730178 2
1.5
U
WEF-0001
For mounting together with Ceiling bracket 5 to provide vertical pieces.
L
mm
292.5
382.5
495
697.5
990
2970
*Ean-code=732167+Part.no+C (control figure)
Pre-galv
Part. No. C*
725357 9
725358 6
725359 3
725360 9
725361 6
721102 5
Hot dip galv
Part. No. C*
715879 9
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
716309 0
23
31
40
56
80
240
MAX 20 o
1 Pendant/Fixing rail 24/34,
1 Ceiling bracket 5 and 1 Screw
set 22S together provide a
vertical piece that can be
mounted with up to 20º slope.
Side mounting of pendant/fixing
rails may be done using
2 Expansion bolts.
91
End plug 28C,D,E and F
WEF-0003
Used for mounting in pendant ends to provide protection against personal injury.
End plug 28C
End plug 28D
End plug 28E
End plug 28F
End plug 28C fits Vertical piece 2
and Pendant/ Fixing rail 24/34.
End plug 28E fits Vertical piece
2F and Pendant/ Fixing rail 24/48.
92
End plug 28F fits Vertical piece
20FS and Pendant/ Fixing rail
24/20FS.
End plug 28D fits Vertical piece 20
and Pendant/ Fixing rail 24/20.
Orange plastic
Part. No. C*
Weight kg
100 pcs
789875 6
709020 4
709021 1
789876 3
0.5
1
0.5
4
Ceiling bracket 5
WEF-0001
Can be used together with Pendant/Fixing rail 24/34.
Ceiling bracket 5
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
721101 2
718640 2
716293 2
35
Max 20°
1 Pendant/Fixing rail 24/34, 1
Ceiling bracket 5 and 1 Screw
set 22S together provide a vertical piece that can be mounted
with up to 20º slope.
Breaking load for rail 24/34
=1000 kg (10 kN).
Breaking load for rail 24/48
= 1200 kg (12 kN).
Ceiling bracket 5 is installed
against the back of the pendant
rail by turning the bracket 90º
and by pushing the lip into the
hole of the rail.
Next the bracket is turned back
again and fastened in the desired
position with 1 Screw set 22S.
When installing against a horizontal ceiling the bolt must be
locked in the recess of the slot
for better stability sideways.
93
Bracket 60/40
WEF-0001
Bracket 60/40 is installed together with Pendant/Fixing rail 24/34 to reduce the deflection of long pendants.
Bracket 60/40
Use Bracket 60/40 with Pendant/Fixing rail 24/34 to reduce the
deflection of long pendants. Cut the pendant/fixing rail to a suitable
length on site.
94
Hot dip galv.
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
718904 5
720531 8
10
Pendant bar 1
WEF-0001
Installed in order to reduce the deflection of long Vertical pieces 2F and 20.
A
A
B
Pendant bar 1/300-800
B
Pendant bar 1-1500
A
mm
B
mm
Pendant bar 1-300
80
300
Pendant bar 1-500
130
500
Pendant bar 1-800
215
800
Pendant bar 1-1500
May vary
*EAN-code=732167+Part.no+C (control figure) **Produced to order
Hot dip galv.
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
717640 3
717641 0
717642 7
718903 8
717643 4**
717644 1**
717645 8**
720530 1**
50
80
125
560
In order to reduce deflection of Vertical piece 2F for heavy loads on
Internal cantilever arm W17/40 and Cantilever arm 50/50L, Pendant
bar 1 is installed with T-bolt. Loadings in accordance with table
below.
Loading table for Cantilever arm W17/40
Max. loading F at 3˚ deflection of cantilever arm
Cantilever arm
type
Without bar
W17/40-100
200
300
400
With bar 1-300
W17/40-100
200
300
400
With bar 1-500
W17/40-100
200
300
400
With bar 1-800
W17/40-100
200
300
400
2F-280
kN
kg
0.65
65
0.60
60
0.70
70
0.55
55
2F-370
kN
kg
0.65
65
0.60
60
0.70
70
0.55
55
2F-505
kN
kg
0.60
60
0.50
50
0.70
70
0.55
55
0.75
75
0.60
60
0.80
80
0.70
70
2F-730
kN
kg
0.55
55
0.50
50
0.65
65
0.50
50
0.70
70
0.55
55
0.75
75
0.65
65
0.90
90
0.70
70
0.95
95
0.70
70
2F-1000
kN
kg
0.55
55
0.45
45
0.55
55
0.45
45
0.65
65
0.50
50
0.70
70
0.50
50
0.70
70
0.60
60
0.80
80
0.55
55
0.80
80
0.60
60
0.85
85
0.65
65
95
Pendant strip W33
WEF-0001
The Pendant strip W33 is delivered in straight 1 m lengths and bent on site.
Pendant strip W33
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
721786 1
729059 8
19
The Pendant strip W33 is
delivered straight. Can be bent
on site. Pendants longer than
1 m are joined by overlapping
using Screw set W36/W36C.
96
If an adjustment of pendant
length is required this can be
achieved by cutting the strip in
the middle and overlapping the
two parts so that a joint can be
achieved using Screw set W36/
W36C.
Mounted in open intersections
for ceiling installation. Mounted
with Screw set W36/W36C in
Support bracket/joint W7.
Pendant rail W32
WEF-0001
Pendant rail W32 can be installed in ceilings together with Ceiling attachment W31 or Ogebe fixing type E.
Pre-galv
Part. No. C*
Hot dip galv
Part. No. C*
Pre-galv.
White30
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
Pendant rail W32
716798 2
734620 2
729058 1
783122 7
180
The Pendant rail W32 is cut to
the required length and mounted
in the ceiling with Ceiling attachment W31 and Pendant attachment W21 mounted onto Support
bracket/joint W7.
For lighter installations with
small loads, only one half of
the Pendant attachment W21 is
mounted in Support bracket W7
The second part of the Pendant
attachment W21 is used as a
ceiling bracket. The Pendant rail
W32 is mounted using Screw set
W37.
The Pendant rail W32 can be
joined by placing overlapping
and assembly using Screw set
W37
Using Locking clamp W77, the
Pendant rail W32 can be
mounted between two lighting
trunkings or cable trays either as
a stabiliser or to form a simple
dukt.
97
Ceiling attachment W31 for Pendant rail W32.
Plate
thickness
mm
2
WEF-0001
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
716816 3
734619 6
729063 5
783120 3
6.5
The Ceiling attachment W31 is
mounted in concrete ceilings with
one or two Expansion bolts.
Pendant rail W32 is mounted
with Screw set W37.
The Ceiling attachment W31 can
be rotated 90˚.
be mounted directly in a slanted
ceiling with Screw set W37.
The Ceiling attachment W31
can be mounted directly in TP
ceilings using an Ogebe fixing
type E.
be mounted onto a concrete
beam with Expansion bolts.
Locking clamp W77
Mounted to lock Pendant rail W32 when installed between lighting trunking or cable trays as a stabilizer.
Locking clamp W77
WEF-0001
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
1.25
716797 5
729060 4
1.5
Pendant rail W32 mounted with
Screw set W36/W36C or W34.
98
Locking clamp W77 used when Pendant rail W32 is mounted
between two Lighting trunking W70/W71 or cable trays as a stabilizer.
Locking clamp W77 fixed to the
fold of trunking/tray with a pair of
pliers.
Fixing rail 24/26x53, casting-in
For casting-in in walls and ceilings.
WEF-0001
lx
Fixing rail 24/26x53 for casting-in
10.39 cm4
Transverse force
Wx
ly
3
3.92 cm
2.78 cm4
Wy
Hot dip galv.
Part. No. C*
Weight kg
100 pcs
1.90 cm3
768063 4
970
Fixing rail 24/26 x 53 for castingin in walls and ceilings. Mount
cantilever arms with T-bolt 26F.
Max. pull-out load:
1000 kg/0.5 m of casting-in fixing
rail (Concrete class K200).
99
Vertical piece 2FPK
For installations in ceilings close to wall.
L
mm
WEF-0001
Hot dip galv.
Part. No. C*
Vertical piece 2FPK-300
280
788655 5
500
788656 2
730
788657 9
1000
788658 6
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
788660 9**
788661 6**
788662 3**
788663 0**
120
155
205
250
Loadings
Vertical piece 2FPK mounted in Vertical piece 2FPK mounted in Deflection of Vertical piece 2FPK
the inner hole.
the outer hole.
is reduced by installing Pendant
Breaking load=1400 kg
Breaking load=200 kg
bar 1. Loadings in accordance
(14 kN) at symmetrical loading.
(2kN) at symmetrical loading.
with table below.
Max permitted load F at max permitted deflection 1/20 of the length L of the cantilever arm in accordance to standard IEC 61537.
Cantilever arm
Without
Pendant bar 1
With
Pendant bar 1/500
50-200 L=250
50-400 L=450
50-600 L=650
50-200 L=250
50-400 L=450
50-600 L=650
2FPK-300
kg
140
145
105
Vertical piece 2FPK can be
mounted in ceiling close to wall.
100
Vertical piece 2FPK is suitable
for floor mounting.
2FPK-500
kg
130
135
100
2FPK-750
kg
100
95
80
155
165
115
2FPK-1000
kg
80
75
60
125
120
90
Vertical piece 2
WEF-0001
To be used for installation of centre pendant of Cable trays W1 and W3, mesh trays and lighting trunking.
L
mm
Hot dip galv.
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
279
392
504
729
1022
717191 0
717192 7
717193 4
717194 1
717195 8
716283 3
716284 0
716285 7
716286 4
716287 1
52
62
72
93
120
Mount Vertical piece 2 using an
Expansion bolt alt. Concrete
screw.
Mount Vertical piece 2 on Fixing
rail 24/26x53 for casting-in using
T-bolt.
Vertical piece 2 may be joined to
achieve the required length using
Pendant/Fixing rail 24/34 and
Pendant joint 2J.
Support bracket W1940/W1960
can be mounted on Vertical piece
2 with Angle bracket W8S.
Use Screw set W36/W36C.
Support bracket W1940/1960
mounted in the fixing plate of the
vertical piece with Screw set
W36/W36C.
Use Pendant joint 2J to join two
Vertical pieces 2.
101
Vertical piece 2F
WEF-0001
Used for installation of Internal cantilever arm W17/40,
Adjustable cantilever arm W1840/W1860 or Cantilever arm 50.
Vertical piece 2F-280
L
mm
Hot dip galv.
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
280
370
505
730
1000
1495
717196 5
717197 2
717198 9
717199 6
717200 9
787276 3
717201 6
717202 3
717203 0
717204 7
717205 4
787277 0
80
100
130
170
220
290
Mounted in ceiling with Expansion bolt alt. Concrete screw.
102
Cantilever arm 50 is mounted
with a T-bolt.
mounted with a T-bolt.
In order to reduce the deflection
of Vertical piece 2F for heavy
loads on Internal cantilever arm
W17/40 and Adjustable cantilever arm W1840/W1860, Pendant bar 1 is installed.
Vertical piece 20
WEF-0001
Used for vertical installation with cantilever arms from a ceiling or on a floor.
L
mm
Hot dip galv.
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
505
730
1000
1495
1990
2980
715723 5
715724 2
715725 9
715726 6
715727 3
715728 0
716276 5
716277 2
716278 9
716279 6
716280 2
716281 9
250
330
440
620
800
1180
Mounted in ceiling with Expansion bolt alt. Concrete screw.
mounted with a T-bolt.
On Vertical piece 20, mount Can- Vertical piece 20 may be
tilever arm 50 using a T-bolt.
equipped with a protective
orange coloured End plug 28D.
103
End bracket WN17
WEF-0001
Used as vertical piece, for example mounted on Support bracket/joint W7 to achieve an invisible suspension.
End bracket WN17
End bracket WN17 can
be mounted as vertical piece on
Support bracket/joint W7, use
Screw set W36/W36C.
The end brackets are joined with
2 Screw sets 22S.
Max symmetrical load on the end
bracket is 100 kg at a tightening
torque of 10.4 Nm.
104
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
Pre-galv.
White80
Part. No. C*
Weight kg
100 pcs
733090 4
733091 1
733092 8
10
Angle bracket W8
WEF-0001
The angle bracket is mounted in the tray horizontally to a wall or vertically to a floor.
The angle bracket can also be mounted as a pendant bracket in the lighting trunking.
It can also be used as stabilizing angle.
Pre-galv.
Part. No. C*
Angle bracket W8
716821 7
Hot dip galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
728883 0
729066 6
783124 1
6
2 Angle brackets W8 are
mounted in Cable trays W1/40 or
W3/40 using 2 Screw sets W38P
for horizontal connection to wall
and vertical connection to floor.
Can be mounted with legs
pointing inwards or outwards.
Angle bracket W8 mounted in
bottom of lighting trunking with
Screw set W36/W36C.
Expansion bolts are used for
installation in concrete walls.
In sheet metal walls mounting is
achieved with an Ogebe fixing
type ED.
Horizontal installation of Cable
tray W3/W1 on floor or vertically
on wall.
The angle bracket W8 can be
turned to reduce the distance to
floor or wall.
Horizontal installation of Cable
tray W3 on floor or vertically on
wall.
The angle bracket W8 can be
turned to reduce the distance to
floor or wall.
The Angle bracket W8 is
mounted to achieve clearance
from wall or where there is a
large asymmetric load on the tray
at pendant installation. Mounted
at a distance of 1.5-2 m.
Angle bracket mounted in bottom
of lighting trunking with Screw
set W36/W36C as pendant
attachment.
105
Angle bracket W8S
WEF-0001
To be used for various installations of Pendant/Fixing rail 24/34, support brackets etc.
Pre-galv.
Part. No. C*
Angle bracket W8S
728071 1
Hot dip galv.
Part. No. C*
Pre-galv.
White80
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
726873 3
726874 0
783126 5
8
Vertical piece 2 or Pendant/
Fixing rail 24/34 can be mounted
with Angle bracket W8S directly
into the lighting trunking.
Use Screw set 22S.
Support bracket 3 can be
Support bracket W1940/ W1960
mounted in ceilings with Angle
can be mounted on Ceiling
bracket W8S and Screw set 22S. bracket 5 with Angle bracket
W8S and Screw set 22S.
Clamp suspension of cable tray
can be made with Pendant/Fixing rail 24/34, Angle bracket W8S
and Screw set 22S.
Angle bracket W8S can be used
for installations in Pendant/Fixing
rail 24/34. Use Screw set
22S. An easy way to build stands
for electrical cabinets.
106
Support bracket/joint W7 can be
mounted directly on Vertical
piece 2 with Angle bracket W8S
and Screw set 22S.
Does not apply to widths used for
joining only.
Support bracket W1940/ W1960
can be mounted on Vertical piece
2 with Angle bracket W8S and
Screw set 22S.
WEF-0001
Pieces of Polystyrene at both ends makes it possible to adjust the height of the tray.
Fixing tray N-300 for casting-in
Fixing tray N-400 for casting-in
A
mm
Pre-galv.
Part. No. C*
Weight kg
100 pcs
330
430
782695 7
782696 4
1800
2200
mounted in the mould.
Fixing tray N adjusted onto the
mould (from out- or inside).
The length is adjustable to ceiling
and floor by moving the pieces of
Polystyrene, total height min
2400-max 3000 mm.
The mesh tray mounted into the
Fixing tray N is used for
mounting of cables.
107
Lashing wire
WEF-0011
For lashing of wires in mesh trays.
HTR-2303 Lashing wire, stainless steel, white PVC
HTR-2313 Lashing wire, stainless steel, black PVC
HT-2304 Lashing wire, white PVC
HT-2314 Lashing wire, black PVC
Diam
mm
Breaking load
kg
Part. No. C*
Weight kg
100 m
1.25
1.25
1.5
1.5
92
92
25
25
713686 5
713687 2
713684 1
713685 8
1.3
1.3
1.8
1.8
Lashing wire is used for
mounting in mesh trays.
WEF-0001
For installation in ceilings. Wire Ø4.4 mm.
2000
B
A
A
B
Electro-galv.
Part. No. C*
100 60
727991 3
Mounted in ceilings with
Ceiling bracket WN16.
108
Mounted under desks with
Ceiling bracket WN16.
Hot dip galv.
Part. No. C*
Stainl. steel
(AISI316)
Part. No. C*
Electro-galv.
White80
Part. No. C*
Weight kg
100 pcs
727992 0
727993 7
727994 4
100
For installation of Ceiling mesh tray WN2.
WEF-0001
Electro-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
Stainl. steel
(AISI316)
Part. No. C*
Electro-galv.
White80
Part. No. C*
Weight kg
100 pcs
727996 8
727997 5
727998 2
5
727995 1
Ceiling mesh tray WN2 must be
mounted with Ceiling bracket
WN16.
Ceiling mesh tray WN2 mounted
under desks with Ceiling bracket
WN16.
Earth clamp W79
Suitable for mounting on Junction box plate W24. Used for protective earthing.
Earth clamp W79
WEF-0001
Electro-galv.
Part. No. C*
Weight kg
100 st
716640 4
0.2
Earth clamps W79 are intended for use when the earthing of
mounting plates for the installation of machines complying with
regulations for use of high tension current is required.
The junction box plate’s (mounting plate’s) oval holes facilitate the
moving of the Earth clamp W79 so that it is always located under the
machine casing.
If the machine’s earth clamp is not approved for splicing of earth
cable, this must pass in unbroken state through the machine’s earth
clamp to the earth clamp in the junction box plate.
Wibe Junction box plate W24 and Earth clamp W79 are approved by
the National Electrical Inspectorate 850513 in accordance with
annotation S24-138/85.
109
Cover plate W16
WEF-0001
Mounted with Screw set W36/W36C under 90˚ bends, T- and X-junction
if one needs to level out differences in levels between tray and junction.
A
mm
Cover plate W16-70
70
Cover plate W16-100
100
Cover plate W16-200
200
Cover plate W16-300
300
Cover plate W16-400
400
Mounted with Screw set W36/
W36C under X-junction W13/40 if
one needs to level out differences
in height between tray and bend.
110
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
1.5
1.5
1.5
1.5
1.5
718036 3
718037 0
718038 7
718039 4
718040 0
729154 0
729155 7
729156 4
729157 1
729158 8
6
12
48
108
192
Dividing strip 39
WEF-0001
Mounted to divide a cable tray or lighting trunking into two or more channels in order to
separate different types of cables and pipes. Mounted with Support band W6.
Plate
thickness
mm
H
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Pre-galv.
White80
Part. No. C*
Weight kg
100 pcs
0.6
0.6
24
55
718835 2
725785 0
782787 9
717950 3
725786 7
46
73
Plate
thickness
0.6
0.6
H
mm
Hot dip galv.
Part. No. C*
Stainl. steel
(AISI316L)
Part. No. C*
Weight kg
100 pcs
24
55
731747 9
732983 0
725593 1
725594 8
46
73
Used to separate tray or trunking in two or more ducts thereby
separating control cables from other cables and pipes. The hole
structure at distances of 250 mm permits two fixing opportunities
with Support bands W6 even after cutting.
111
Insert piece W39
WEF-0021
Insert piece W39 is used to join Dividing strips W39.
Insert piece W39
Plastic
Part. No. C*
Weight kg
100 pcs
716824 8
3
Insert piece W39 is used to join Dividing strips W39 and is mounted
on Support bracket/joint W7 or Internal cantilever arm W17/40.
When mounting over Internal cantilever arm W17/40, break away
plastic bit from component.
Support band W6
WEF-0001
The Support band W6 is mounted to fix the lateral position of one or several Dividing strips 39.
Support band W6-70
Support band W6-100
Support band W6-200
Support band W6-300
Support band W6-400
Support band W6-500
Support band W6-600
L
mm
Pre-galv.
Part. No. C*
Weight kg
100 pcs
67
97
197
297
397
497
597
718828 4
718829 1
718830 7
718831 4
718832 1
718833 8
718834 5
1.0
1.4
2.8
4.3
5.7
7.2
8.6
Support band W6 is mounted to fix one or more Dividing strips 39 laterally. The holes in the support band and the locking pins in Dividing
strip 39 allow for a fixed division with intervals of 25 mm.
112
Tele-conduit 36
WEF-0001
With knock-out holes
Tele-conduit is installed where a separate tray is required for low-tension cables.
B
mm
C
mm
Pre-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
Pre-galv.
White80
Part. No. C*
Weight kg
100 pcs
Tele-conduit 36-50
42
Tele-conduit 36-100
92
Tele-conduit 36-200
192
50
100
200
725065 3
725066 0
725067 7
731748 6
731749 3
731750 9
725068 4
725069 1
725070 7
94
142
238
Make a hole for cable passage
by pushing out the washer from
below with a screw driver or
similar.
113
Cover W5
WEF-0001
Length 2000 mm. The cover is used for screening control cables and in dusty and dirty premises.
Cover W5-60
Cover W5-70
Cover W5-100
Cover W5-150
Cover W5-200
Cover W5-300
Cover W5-400
Cover W5-500
Cover W5-600
t
mm
B
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
0.7
0.7
0.7
0.7
0.7
0.7
1.0
1.0
0.7
61
71
101
151
201
301
401
501
601
732213 8
732214 5
732215 2
732216 9
732217 6
732218 3
732219 0
732220 6
732221 3
734133 7
729015 4
729016 1
733134 5
729017 8
729018 5
729019 2
729020 8
729021 5
90
100
140
190
250
360
680
840
700
t
mm
B
mm
Cover W5-60
1.0
61
Cover W5-70
1.0
71
Cover W5-100
1.0
101
Cover W5-150
1.0
151
Cover W5-200
1.0
201
Cover W5-300
1.0
301
Cover W5-400
1.0
401
Cover W5-500
1.0
501
Cover W5-600
1.0
601
Hot dip galv.
Part. No. C*
ZINKPOX®
White80
Part. No. C*
Weight kg
100 pcs
732261 9
732262 6
732263 3
732264 0
732265 7
732266 4
732267 1
732268 8
732269 5
782362 8
782363 5
782364 2
782365 9
782366 6
782367 3
782368 0
782369 7
782370 3
140
160
210
290
370
540
710
880
1050
Used for screening of control
cables and in dusty and dirty
premises.
114
Covers must be mounted on cable
trays with Cover clamp W62.
Cover clamp W62
WEF-0001
Used for fixing covers on Trays W1 and W3 as well as on Lighting trunking W70/W71.
Cover clamp W62
Stainl. steel
(AISI304)
Part. No. C*
Weight kg
100 pcs
730186 7
0.8
Cover clamp W62 used for
fixing the covers on Cable tray
W1 and W3 as well as on
Lighting trunkings W70 and W71.
Start by pressing the Cover
clamp W62 over the sides of the
cover. Then snap the cover over
the folded edges of the tray.
6 Cover clamps W62 are needed
per cover.
115
Combi bracket 53
Used for mounting cable trays, mesh trays and cable ladders on seemed roofing sheet etc.
WEF-0001,-0031
Hot dip galv.
Part. No. C*
Combi bracket 53
Insulating plate 54
Plastic
Part. No. C*
Weight kg
100 pcs
787223 7
26
2
782353 6
Breaking load*
Type of roofing sheet
Insulating plate
Permitted load
Bandsheet Prelac
Copper sheeting
Bandsheet Prelac
Copper sheeting
No
Yes
No
Yes
F1=100 kg
F2=50 kg
F3=100 kg
F4=50 kg
* Loading values and fixing of roof sheet - follow the supplier´s recommendations
Test have been made of:
Bandsheet Prelaq BLX t=0.6 SSAB tunnplåt
Copper sheeting annealed SS 5015-80 t=0.6
Tightening torque at test=60Nm
Combi bracket 53 mounted on
seamed roofing sheet.
Alternative mounting of Combi
bracket 53.
In order to avoid contact between
Combi bracket 53 and copper
sheeting, Insulating plate 54
must be used.
Alternative mounting of Combi
bracket 53 and Insulating plate
54.
Cable ladder mounted across the
seams of the roofing sheets with
Combi bracket 53, Wall bracket
11/25 and Screw set 22S.
Cable ladder mounted along the
seams of the roofing sheets with
Combi bracket 53, Wall bracket
11/25, Screw set 22S, Pendant/
Fixing rail 24/48 and T-bolt 26F.
Mesh tray mounted along the
seams of the roofing sheets
with Combi bracket 53 and
accessories from the Mesh tray
program.
Mesh tray mounted across the
seams of the roofing sheets
with Combi bracket 53 and
accessories from the Mesh tray
program.
116
Strip fixing W44
WEF-0022
The Strip fixing W44 enables strapping of cables in an unperforated tray.
Strip fixing W44
*EAN-code=732167+Part.no+C(control figure)
Plastic (black)
Part. No. C*
Weight kg
100 pcs
718469 9
1.0
The Strip fixing W44 is provided with double sided adhesive tape and is attached to the tray bottom.
Alternatively, blind rivets or self-tapping screws can be used.
When mounting with double sided adhesive tape, the surface on the tray bottom must be wiped clean.
Loads may not be applied until after 24 hours. Full adhesion is obtained after 72 hours in 21˚C. Ideal
application temperature is 21˚-38˚C. Application below normal room temperature is not recommended.
Each Strip fixing W44 can be split up in 2 to 6 pieces. Supplied with 50 pieces in a plastic bag.
Used to protect the cables from damage.
WEF-0030
Plastic
Part. No. C*
Weight kg
100 pcs
787211 4
6.1
When cutting a cable tray you can
mount Protection strip W48 to
protect the cables from damage.
117
For mounting light fittings between two parallel Cable trays W1/W3 or Lighting trunking W70/W71.
Dimension H is specified when ordering.
H
mm
**
**Selected with respect to height of the light fittings
***H=100 mm
WEF-0001
Plate
thickness
mm
Pre-galv
Part. No. C*
Pre-galv.
White80
Part. No. C*
Weight kg
100 pcs
2.5
720520 2
720785 5
25***
Repair paint
Galvafroid for repair of damaged places on pre-galvanized or hot dip galvanized cable trays and accessories.
Repair paint for minor damages of powder coated products.
Anti-corrosive paint "Galvafroid", tin
Repair paint White RAL 9003 Gloss 30, spray bottle
Repair paint White RAL 9010 Gloss 80, spray bottle
WEF-0013, 0016
Volume
l
Part. No. C*
Weight kg
100 pcs
0.3
0.4
0.4
717637 3
739713 6
728027 8
86
60
60
Galvafroid used to increase the
protection of cut or damaged
places.Applied with a colour
brush.
118
Repair paint in spray bottle
for repainting of minor paint
damages.
Screw set 22S
For mounting of Ceiling bracket 5 on Pendant/Fixing rail 24/34 and
Cantilever arm 80 on Vertical piece 7 or Wall bracket 80 etc.
Screw set 22S (bolt MVBF8x16+nut M6MF8)
WEF-0001
Hot dip galv.
Part. No. C*
Stainl. steel
(AISI316)
Part. No. C*
Weight kg
100 pcs
713694 0
725582 5
1.9
Spring nut M8
For permanent mounting of fittings (instrument cabinets etc.) on Pendant/Fixing rail 24/48.
Spring nut M8
WEF-0001
Hot dip galv.
Part. No. C*
Weight kg
100 pcs
716407 3
2.7
Mounting set W78
For mounting of Threaded rod M10 W76 in plate or light concrete ceilings.
WEF-0001
Mounting set W78 (washer diam.50+nut M6M10)
Hot dip galv.
Part. No. C*
Weight kg
100 pcs
717069 2
5.5
Screw set W36
For mounting of pendant attachments in Support bracket/Joint W7.
WEF-0001
Electro-galv.
Part. No. C*
Stainl. steel
(AISI316)
Part. No. C*
Weight kg
100 pcs
715646 7
725581 8
1.2
Screw set W36 (bolt MVBF8x16+nut M6MF8)
Screw set W36C
Slotted screw used for mounting of pendant attachments in Support bracket/joint W7.
Screw set W36C (Slotted screw M8x16+nut M6MF 8 toothed)
WEF-0001
Electro-galv.
Part. No. C*
Weight kg
100 pcs
783500 3
1.8
119
Screw set W37
For assembly of Pendant attachment W21 and Ceiling attachment W31 with Pendant rail W32.
For joining of Pendant rail W32.
Screw set W37 (bolt MVBF 8x35+nut M6MF 8)
WEF-0001
Electro-galv.
Part. No. C*
Stainl. steel
(AISI316)
Part. No. C*
Weight kg
100 pcs
716799 9
725586 3
2.8
Screw set W38P
Used for mounting of joints, bends, junctions, Shade ledge W26 and Integrated ceiling support channel W27.
Screw set W38P pierces through lacquered surfaces securing potential balancing.
N. B. The joints must be unlacquered. Patented.
Electro-galv.
Part. No. C*
Dacromet
Part. No. C*
Screw set W38P
735177 0
733258 8
*Ean-code=732167+Part.no+C (control figure) **White laquered screw head
WEF-0001
Electro-galv.
White60**
Part. No. C*
Weight kg
100 pcs
782216 4
0.4
Screw set W34
For mounting Tray W3 on Cantilever arm 50.
For mounting Junction box plate W24 in Tray W3, Lighting trunking W70 and W71.
For mounting Locking clamp W77 or Angle bracket W8 onto Pendant rail W32.
For assembly of Angle bracket W8 (light fitting bracket).
For joining of Installation Trays W4 and installations with Profile W-swing 2.
Screw set W34 (bolt MSCS 6x12+nut M6MF6)
WEF-0001
Dacromet
Part. No. C*
Electro-galv.
Part. No. C*
Stainl. steel
(AISI316)
Part. No. C*
Weight kg
100 st
734646 2
718473 6
725589 4
0.8
Screw W40
For locking of T-joint W29 in open junctions.
Screw W40 (screw RXS ST 5.5x13-H)
Electro-galv
Part. No. C*
Weight kg
100 pcs
721868 4
0.3
Locking plug W41
For quick locking of joints, bends and branches in cable trays and lighting trunking.
Locking plug W41
120
WEF-0004
Plastic
Part. No. C*
Weight kg
100 pcs
718645 7
0.1
T-bolt 26F
WEF-0002
Used for mounting with Pendant/Fixing rails.
D
A
L
T-bolt 26F/M8
T-bolt 26F/M10
(For P/F-rail 24/48)
D
L
mm
T-bolt 26F
M8
30
T-bolt 26F
M10
30
T-bolt 26F
M8
40
T-bolt 26F
M10
40
T-bolt 26F
M8
50
T-bolt 26F
M10
50
A
mm
Electro-galv.
Part. No. C*
Hot dip galv.
Part. No. C*
Stainl. steel
(AISI316)
Part. No. C*
Weight kg
100 pcs
24
24
34
34
44
44
734983 8
734864 0
734984 5
734865 7
734985 2
734866 4
734744 5
716794 4
734745 2
716795 1
734746 9
716796 8
734986 9
728596 9
734987 6
728597 6
734988 3
728598 3
4.5
7
5
7.5
5.5
8
Max permitted extraction force
T-bolt 26F M8/M10 + P/F-rail 24/48 +Washer 8,4x19x1,5
T-bolt 26F M8 + P/F-rail 24/48 + Washer 9x35x2
T-bolt 26F M10 + P/F-rail 24/48 + Washer 9x35x2
Installation of Pendant/Fixing rail
on floor (or wall) with Angle
bracket 5L and T-bolt.
Check the position mark on the
bolt to ensure the right position of
the T-bolt in the rail.
T-bolt M8 makes it possible to
mount through the perforation of
Pendant/Fixing rail 24/48.
121
Expansion bolts
Electro-galvanized, hot dip galvanized or stainless steel AISI316.
For installation of all Wibe cantilever arms and vertical pieces.
D
mm
L
mm
G
mm
WEF-0001
Electro-galv
Part. No. C*
Hot dip galv.
Part. No. C*
Stainless steel
(AISI316)
Part. No. C*
Expansion bolt M6x40**
6
40
18
782222 5
782237 9
782252 2
6
65
28
782223 2
782238 6
782253 9
8
50
24
782224 9
782239 3
782254 6
8
95
41
782225 6
782240 9
782255 3
8
120
66
782226 3
782241 6
782256 0
Expansion bolt M10x60
10
60
29
782227 0
782242 3
782257 7
10
80
34
782228 7
782243 0
782258 4
10
100
54
782229 4
782244 7
782259 1
12
85
35
782230 0
782245 4
782260 7
12
100
50
782231 7
782246 1
782261 4
12
145
82
787052 3
787053 0
787054 7
16
110
53
782232 4
782247 8
782262 1
16
125
63
782233 1
782248 5
782263 8
16
150
76
782234 8
782249 2
782264 5
20
170
55
782235 5
782250 8
782265 2
20
220
55
782236 2
782251 5
782266 9
** M6 and M8 are delivered with an extra washer with a larger diameter. This washer must be mounted close to the
cantilever arm or vertical piece. The smaller standard washer must be put on top of the bigger washer close to the nut.
D1= Drill diameter
M = Installation depth
B = Min. drilling depth
T = Material thickness
Data for installation
Dim
M6x40
M6x65
M8x50
M8x95
M8x120
M10x60
M10x80
M10x100
M12x85
M12x100
M12x145
M16x110
M16x125
M16x150
M20x170
M20x220
122
D1
mm
6
6
8
8
8
10
10
10
12
12
12
16
16
16
20
20
B
mm
35
50
45
65
65
60
70
70
80
80
80
105
105
105
150
150
M
mm
30
50
35
55
55
40
60
60
50
75
75
100
100
100
120
120
T
mm
5
15
5
30
55
5
10
30
5
20
60
5
20
45
20
70
Tightening
moment
Nm
7
7
20
20
20
35
35
35
55
55
55
100
100
100
240
240
Weight kg
100 pcs
1.04
1.54
2.22
3.61
4.35
4.44
5.32
6.28
8.17
9.23
12.5
18.57
20.4
23.9
44.83
57.02
Expansion bolts
WEF-0001
Extraction force
Permitted extraction force in kN for various concrete qualities
Dim
Installation
depth mm
C25
Concrete class
C30
C35
C40
M6
M6
M6
M8
M8
M8
M10
M10
M12
M12
M12
M16
M20
30
40
50
35
40
55
40
60
50
75
80
100
120
1.4
2.3
3.2
1.6
2.0
3.3
2.2
4.0
3.1
6.5
7.5
9.4
12.3
1.6
2.8
3.5
1.8
2.4
3.8
2.5
4.5
3.5
7.4
8.5
10.7
14.0
1.8
2.9
3.7
2.0
2.5
4.0
2.8
5.0
3.9
7.8
9.0
12.0
15.7
2.0
3.0
4.0
2.3
2.9
4.7
3.1
5.6
4.4
9.3
10.5
13.4
17.4
Transverse force
Permitted transverse force in kN for various concrete qualities
Dim
Installation
depth mm
C25
Concrete class
C30
C35
C40
M6
M6
M6
M8
M8
M8
M10
M10
M12
M12
M12
M16
M20
30
40
50
35
40
55
40
60
50
75
80
100
120
1.1
1.6
2.2
1.4
2.0
3.8
1.6
5.7
2.2
9.6
10.6
12.3
15.9
1.3
2.1
2.4
1.6
2.2
4.0
1.8
6.0
2.5
9.9
11.0
12.8
17.0
1.5
2.2
2.6
1.8
2.4
4.2
2.0
6.2
2.7
10.2
11.4
13.2
17.5
1.6
2.3
2.8
1.9
2.5
4.4
2.2
6.5
3.0
10.5
12.2
13.7
19.3
123
Fixing system
124
Concrete screw MMS-S
For installation with cantilever arms and vertical pieces.
Concrete screw with hexagonal head and special thread constructed for safe fixing in concrete or brickwork.
Suitable for fixing of tubes, electrical installations, rails, handrails, machines, ventilating ducts, wood constructions.
❑ Easy to install
❑ High extraction values are obtained due to the special thread. The drill diameter is the same as the root diameter of the screw
which gives a solid fixing inside the hole.
❑ Can be dismounted and reinstalled without reduced extraction force.
❑ A weaker drill can be used compared to using anchor, expansion bolt, screw and plug.
❑ Suitable in environments which are fire classified.
Installation of cantilever arms.
Installation of vertical pieces.
Electro-galvanized
WEF-0001
A = Drill diameter
B = Min. installation depth
C = Min. drilling depth
F = Extraction force kN**
T = Transverse force kN
N = Width of jaws
**For concrete class C25
Part. No. C*
F
kN
T
kN
N
mm
ØxL
mm
A
mm
B
mm
C
mm
Number/
package
Weight kg
100 pcs
MMS-S 6x401
787067 7
2.40
2.2
10
6x40
5
30
50
200
0.74
MMS-S
6x501
787047 9
2.80
2.2
10
6x50
5
30
50
100
0.92
MMS-S
6x601
787048 6
2.80
2.2
10
6x60
5
30
50
100
1.03
MMS-S 7.5x352
781550 0
2.50
4.8
13
7.5x35
6
30
50
100
1.2
MMS-S 7.5x402
781551 7
2.50
4.8
13
7.5x40
6
30
50
100
1.3
MMS-S 7.5x502
MMS-S 10x60
MMS-S 10x70
MMS-S 10x80
MMS-S 12x80
781552 4
3.00
4.8
13
7.5x50
6
30
50
100
1.4
781553 1
781554 8
781555 5
781556 2
6.10
6.10
7.20
8.00
7.8
7.8
7.8
7.8
16
16
16
18
10x60
10x70
10x80
12x80
8
8
8
10
55
55
55
60
75
75
75
80
50
50
50
25
3.2
3.4
4.0
6.0
1 Washer 7.0x16x1.5 Electro-galv. is included
2 Washer 8.4x19x1.5 Electro-galv. is included
125
Hot dip galvanized
WEF-0001
A = Drill diameter
N = Width of jaws
Part. No. C*
F
kN
T
kN
N
mm
ØxL
mm
A
mm
B
mm
C
mm
Number/
package
Weight kg
100 pcs
MMS-S 6x401
790356 6
2.40
2.2
10
6x40
5
30
50
200
0.74
MMS-S 6x501
790357 3
2.80
2.2
10
6x50
5
30
50
100
0.92
MMS-S 6x601
790358 0
2.80
2.2
10
6x60
5
30
50
100
1.03
MMS-S 7.5x352
790359 7
2.50
4.8
13
7.5x35
6
30
50
100
1.2
MMS-S 7.5x402
790360 3
2.50
4.8
13
7.5x40
6
30
50
100
1.3
MMS-S 7.5x502
MMS-S 10x60
MMS-S 10x70
MMS-S 10x80
MMS-S 12x80
790361 0
3.00
4.8
13
7.5x50
6
30
50
100
1.4
790362 7
790363 4
790364 1
790365 8
6.10
6.10
7.20
8.00
7.8
7.8
7.8
7.8
16
16
16
18
10x60
10x70
10x80
12x80
8
8
8
10
55
55
55
60
75
75
75
80
50
50
50
25
3.2
3.4
4.0
6.0
1 Washer 7.0x16x1.5 Hot dip galv. is included
2 Washer 8.4x19x1.5 Hot dip galv. is inclcluded
Stainless steel AISI316
Concrete screw with soldered phosphatized carbon steel tip.
WEF-0001
L2
L1
A = Drill diameter
N = Width of jaws
MMS-S 7.5x50/653
MMS-S 10x70/85
MMS-S 12x80/100
Part. No. C*
F
kN
T
kN
N
mm
ØxL1/L2
mm
A
mm
B
mm
C
mm
Number/
package
Weight kg
100 pcs
781557 9
3.00
4.8
13
7.5x50/65
6
30
85
50
1.9
781558 6
781559 3
7.20
8.10
7.8
7.8
16
18
10x70/85
12x80/100
8
10
55
60
105
120
50
25
4.4
7.6
3Washer 8.4x24x2.0 AISI316 is incl.
126
Concrete screw MMS-S FL
Electro-galvanized
Concrete screw with flange.
WEF-0001
A = Drill diameter
D = Flange diameter
N = Width of jaws
Part. No. C*
MMS-S FL 6x40
790394 8
MMS-S FL 6x50
790395 5
MMS-S FL 6x60
790396 2
MMS-S FL 7.5x50
790397 9
MMS-S FL 7.5x70
790398 6
MMS-S FL 10x70
790399 3
MMS-S FL 10x80
790400 6
MMS-S FL 12x90
790401 3
MMS-S FL 12x100
790402 0
F
kN
T
kN
N
mm
ØxL
mm
D
mm
A
mm
B
mm
C
mm
Number/
package
Weight kg
100 pcs
2.40
2.80
2.80
3.00
3.00
6.10
7.20
8.00
8.00
2.2
2.2
2.2
4.8
4.8
7.8
7.8
7.8
7.8
10
10
10
13
13
16
16
18
18
6x40
6x50
6x60
7.5x50
7.5x70
10x70
10x80
12x90
12x100
15.0
15.0
15.0
17.5
17.5
19.0
19.0
22.0
22.0
5
5
5
6
6
8
8
10
10
30
30
30
30
30
55
55
60
60
50
50
50
50
50
75
75
80
80
100
100
100
50
50
25
25
25
25
0.8
1.0
1.1
1.6
2.0
3.9
4.5
7.7
8.5
Concrete screw MMS-S FL
Hot dip galvanized
Concrete screw with flange.
WEF-0001
A = Drill diameter
D = Flange diameter
N = Width of jaws
Part. No. C*
MMS-S FL 6x40
790376 4
MMS-S FL 6x50
790377 1
MMS-S FL 6x60
790378 8
MMS-S FL 7.5x50
790379 5
MMS-S FL 7.5x70
790380 1
MMS-S FL 10x70
790381 8
MMS-S FL 10x80
790382 5
MMS-S FL 12x90
790383 2
MMS-S FL 12x100
790384 9
F
kN
T
kN
N
mm
ØxL
mm
D
mm
A
mm
B
mm
C
mm
Number/
package
Weight kg
100 pcs
2.40
2.80
2.80
3.00
3.00
6.10
7.20
8.00
8.00
2.2
2.2
2.2
4.8
4.8
7.8
7.8
7.8
7.8
10
10
10
13
13
16
16
18
18
6x40
6x50
6x60
7.5x50
7.5x70
10x70
10x80
12x90
12x100
15.0
15.0
15.0
17.5
17.5
19.0
19.0
22.0
22.0
5
5
5
6
6
8
8
10
10
30
30
30
30
30
55
55
60
60
50
50
50
50
50
75
75
80
80
100
100
100
50
50
25
25
25
25
0.8
1.0
1.1
1.6
2.0
3.9
4.5
7.7
8.5
127
Concrete screw MMS-PAN
Electro-galvanized
For installation of Pendant strip W33.
Panheaded concrete screw, electro-galvanized and yellow chromated. Torx-recess.
WEF-0001
A = Drill diameter
E = Screw head diameter
Part.No. C*
F
kN
MMS-PAN 5x30
787049 3
0.8
MMS-PAN 5x50
787050 9
1.4
MMS-PAN 6x30
781560 9
2.40
MMS-PAN 7.5x45
781561 6
3.20
MMS-PAN 10x70
781562 3
7.20
T
kN
Torx
ØxL
mm
A
mm
B
mm
C
mm
E
mm
Number/
package
Weight kg
100 pcs
1.4
1.4
2.2
4.8
7.8
T-20
T-20
T-30
T-40
T-40
5x30
5x50
6x30
7.5x45
10x70
4
4
5
6
8
25
25
25
30
55
45
45
45
50
75
7.9
7.9
11.5
13
17
200
200
200
100
50
0.32
0.5
0.65
1.10
3.40
Installation of Pendant strip W33. Mounting with JR-clamp.
Concrete screw MMS-PAN SH
WEF-0001
Electro-galvanized
For installation of Ceiling attachment W31 or Tube pendant attachment W73.
Concrete screw with extra big panhead, electro-galvanized and yellow chromated. Torx-recess.
A = Drill diameter
E = Screw head diameter
Part. No. C*
MMS-PAN SH 7.5x45
781696 5
Installation of Ceiling attachment
W31.
128
F
kN
T
kN
Torx
ØxL
mm
A
mm
B
mm
C
mm
E
mm
Number/
package
Weight kg
100 pcs
3.00 4.8
T-30
7.5x45
6
30
50
17
100
1.4
Concrete screw MMS-ST
Electro-galvanized
WEF-0001
For installation of eye nuts. The screw is specially developed for safe fixing in concrete.
Suitable for tube installations, electrical installations, rails, handrails, machines, ventilating ducts, wood constructions.
A = Drill diameter
E = Length of thread engagement
N = Widths of jaws
M = English thread
T
kN
N
mm
DxL1
mm
L2
mm
M
A
mm
B
mm
C
mm
E
mm
Number/
package
Weight kg
100 pcs
MMS-ST 7.5x70
781563 0
3.20 4.8
MMS-ST 10x80
781564 7
6.51 7.8
10
13
7.5x70
10x80
53
65
M8
M10
6
8
30
55
50
75
13
10
50
50
1.8
3.5
Part. No. C*
F
kN
Installation of eye nut.
Concrete screw MMS-I
Electro-galvanized
For installation of Pendant M8 or M10.
❑ High extraction values are obtained due to the special thread.
The drill diameter is the same as the root diameter of the screw which gives a solid fixing inside the hole.
❑ Can be dismounted and reinstalled without diminished extraction force.
❑ A weaker drill and less drilling depth can be used compared to using anchor, expansion bolt, screw and plug.
❑ Suitable in environments which are fire classified.
WEF-0001
A = Drill diameter
N = Widths of jaws
M = Metrisk gänga
T
kN
N
mm
DxL1
mm
MMS-I 7.5x55
781565 4
3.20 4.8
13
7.5x93
Part. No. C*
F
kN
L2
mm
M
A
mm
B
mm
C
mm
Number/
package
Weight kg
100 pcs
M8/M10
6
30
50
100
1.9
Installation of Threaded rod M8
or M10.
129
Eye screw MMS-R
Electro-galvanized
For installation of wires in ceiling.
WEF-0001
A = Drill diameter
Part. No. C*
F
kN
MMS-R 6x40
781566 1
2.80
T
kN
ØxL
mm
A
mm
B
mm
C
mm
Number/
package
Weight kg
100 pcs
2.2
6x40
5
30
50
250
0.76
Light concrete screw
Electro-galvanized
For installation in porous concrete. Torx-recess.
WEF-0001
E = Head diameter
F = Permitted extraction force kN
Part. No. C*
Light concrete screw 8x100
790412 9
F
kN
Torx
ØxL
mm
B
mm
E
mm
Number/
package
Weight kg
100 pcs
0.67
T-40
8x100
95
14.8
50
2.4
Expansion nail
WEF-0001
Electro-galvanized/ Aluminium
For fixing of light details in concrete.
A = Drill diameter
Expansion nail 5x22
Part. No. C*
ØxL
mm
A
mm
B
mm
C
mm
Number/
package
Weight kg
100 pcs
790413 6
5x22
5
20
30
250
0.5
Mounting tool for Eye screw MMS-R
Electro-galvanized.
Mounting tool for Eye screw MMS-R
130
WEF-0001
Part. No. C*
Number/
package
Weight kg
100 pcs
781567 8
1
5.5
Bitro adapter
Electro-galvanized + plastic.
The Bitro adapter must be installed direct on Hammer drill SDS PLUS.
Drilling machine can be used. Suitable for drilling only in C25 concrete.
Bitro adapter 5, yellow
Bitro adapter 6, green
Bitro adapter 8, red
Bitro adapter 10, blue
WEF-0001
Part. No. C*
For drill
mm
D
mm
L
mm
Number/
package
Weight kg
100 pcs
781568 5
781569 2
781570 8
781571 5
5
6
8
10
10
10
12
14
73
73
80
80
1
1
1
1
2.5
3.0
4.0
5.0
Turn off the hammer function of the drilling machine. Install the Bitro
adapter on the drill. Check that the adapter locks the drill to avoid
turning. Put in Torxbits or Magnetic socket or Square peg + Socket
16/18. When removing the adapter tilt it lightly and pull the bit,
magnetic socket or the square peg.
When mounting use a drilling machine with torque regulator.
Otherwise be very careful. If you let the machine continue to run
when the screw is in bottom it is very easy to destroy the tip of the
drill or that the drill gets stuck or broken. The risk increases with the
length of the drill.
Magnetic socket for Concrete screw MMS-S
Untreated steel.
WEF-0001
Magnetic socket 10x45
Magnetic socket 13x45**
**Can also be used for MMS-I.
Part. No. C*
Dim
mm
D
mm
Number/
package
Weight kg
100 pcs
781572 2
781573 9
10x45
13x45
10
13
1
1
2.5
3.0
Socket for Concrete screw MMS-S
Untreated steel.
To be used together with Square peg.
Part. No. C*
Socket 16
781574 6
Socket 18
781575 3
WEF-0001
Dim
mm
D
mm
Number/
package
Weight kg
100 pcs
16x34
18x34
16
18
1
1
6.0
10.0
131
Bits holder
Stainless steel AISI304.
Bits holder 11x60
WEF-0001
Part. No. C*
Number/
package
Weight kg
100 pcs
781576 0
1
2.5
Square peg
Untreated steel.
To be used with Socket 16 and 18.
Square peg 3/8x50
WEF-0001
Part. No. C*
Number/
package
Weight kg
100 pcs
781577 7
1
2.0
Torxbits
Untreated steel.
To be used with Concrete screw MMS-PAN SH.
Torxbits TX 30x25
Torxbits TX 40x25
132
WEF-0001
Part. No. C*
Number/
package
Weight kg
100 pcs
788552 7
788553 4
2
2
0.5
0.6
Hammer drill SDS PLUS
Untreated steel.
Hammer drill SDS PLUS 4x110
Hammer drill SDS PLUS 5.5x110
Hammer drill SDS PLUS 5.5x160
WEF-0001
Part. No. C*
Dim
mm
Cutting length
of the drill
mm
Number/
package
Weight kg
100 pcs
787021 9
781631 6
781632 3
787022 6
787023 3
781633 0
781634 7
781635 4
787025 7
787026 4
781636 1
781637 8
781638 5
781639 2
787027 1
787028 8
787029 5
4x110
5x110
5x160
5.5x110
5.5x160
6x110
6x160
6x210
7x160
7x210
8x160
8x210
10x160
10x210
12x210
16x300
20x450
50
50
100
50
100
50
100
150
100
150
100
150
100
150
150
230
370
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
3.0
3.5
4.0
4.0
4.0
4.5
5.0
5.5
5.5
6.0
6.0
6.5
7.5
9.0
9.5
20.0
56.0
4x 75
5x 85
5x150
5.5x 85
5.5x150
6x100
6x150
7x100
7x150
7x300
8x150
8x200
10x150
10x200
12x200
16x300
20x400
40
50
60
50
90
60
90
60
90
220
90
135
90
135
135
220
230
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2.0
2.5
2.0
2.0
2.0
2.0
4.0
4.0
4.0
8.0
4.0
6.0
6.0
8.0
10.0
26.0
62.0
Masonry drill WBL/WBE
Tungsten carbide tip.Tool steel shank with plated finish.
Masonry drill WBE 4x 75
787030 1
Masonry drill WBE 5x 85
787031 8
Masonry drill WBL 5x150
787032 5
Masonry drill WBE 5.5x 85
787033 2
Masonry drill WBL 5.5x150
787034 9
Masonry drill WBE 6x100
787035 6
787036 3
Masonry drill WBE 7x100
787037 0
787038 7
787039 4
787040 0
787041 7
787042 4
787043 1
787044 8
787045 5
787046 2
133
Concrete screws - Loadings
Mounting of Wibe concrete screws
To use Wibe concrete screws is both safe and easy. No special tools or machines are required.
The screw performs an exact adapted thread in the bedding which means that no control of the tightening moment is required.
The extraction force of a Wibe concrete screw is better than that of an expansion bolt with the same diameter
You can choose a smaller diameter of a concrete screw than that of an expansion bolt and still receive the same extraction force.
The same concrete screw can be re-used.
Mounting instruction
Use a drill suitable to the screw.
Drill the hole.
Switch off the hammer function.
Mount the Bitro adapter on the
drill. Pull in a bit or socket suitable for the screw to be used.
Mount with drilling machine.
Wibe concrete screws can also
be mounted with regular hand
tools as box sockets.
1. Drill a hole with the same diameter as the root of the screw
(for 6 mm drill 5 mm, for 7.5 mm drill 6 mm, for 10 mm drill 8 mm and for 12 mm drill 10 mm).
The drill depth must be at least 20 mm deeper than the installation depth.
2. Blow the hole free from dust.
3. Mount the concrete screw close to the application bedding, no defined tightening moment is required.
Note – don´t tighten the screw with a higher moment than stated on the package or technical data.
Extraction forces, in kN, depending on installation depth in uncracked concrete C25.
Calculated values with a safety factor of 3.0.
Installation depth
mm
25
30
35
40
45
50
55
60
70
80
MMS-5
MMS-6
MMS-7.5
0.8
1.4
2.02
2.40
2.50
2.80
2.80
2.80
2.15
2.50
2.60
3.00
3.20
4.10
6.10
6.51
2.80
MMS-10
3.50
3.80
4.00
4.30
6.10
7.20
7.90
MMS-12
5.50
6.30
7.20
8.00
8.10
10.00
Transverse forces Concrete screw MMS
Dimensioned transverse force in kN.
Concrete screw
Screw diameter mm
Breaking torsional moment (Nm)
Recommended max
tightening moment (Nm)
MMS-5
MMS-6
MMS-7.5
MMS-10
MMS-12
1.4
2.2
4.8
7.8
7.8
5
12
10
6
24
10
7.5
28
20
10
80
50
12
120
80
Spacing
The above values are valid when the distance from the nearest corner or free edge to the screw is at least
10 x screw diameter. The spacing between two screws must be minimum 20 x screw diameter.
134
Low density anchor TLF
Hot dip galvanized
For fixing in light concrete or clinker concrete. For medium or heavy installations.
Unique advantages:
❑ Long expansion area and heavy expansion – very high loading values
❑ The expansion can be directed - superior loading values even at small edge distances.
❑ Very quick installation – drives in and expands with a hammer and Hammer tool TLF-S
DxL
mm
D1
mm
Drill diameter
mm
Number/
package
Weight kg
100 pcs
8x 65
12x100
12x145
16x130
13
20
20
25
8
12
12
16
50
25
25
10
1.4
4.7
6.2
10.0
Part. No. C*
Low density anchor TLF 8x65**
781782 5
Low density anchor TLF 12x100
781783 2
781784 9
781785 6
**One Hammer tool is incl. in each package.
Loading - All loadings refer to mounting in light concrete Y 500
Max Tightening moment
M=Nm
Extraction force F1
kN
Transverse force
kN
1
6
6
10
0.3
0.6
0.6
0.6
0.3
0.6
0.6
0.6
TLF 8x65 mounted with wood screw TKX Fzb SPAX-5x35
TLF 12x100 mounted with hexagon head wood screw T6S 4.6 Fzv 8x40
Max permitted load F on Cantilever arm 50
50-200
TLF 8x 65
TLF 12x100
TLF 12x145
TLF 16x130
WEF-0006
50-300
50-400
50-500
50-600
Kg
kN
Kg
kN
Kg
kN
Kg
kN
Kg
kN
26
26
26
0.26
0.26
0.26
25
25
25
0.25
0.25
0.25
22
22
22
0.22
0.22
0.22
23
23
23
0.23
0.23
0.23
21
21
21
0.21
0.21
0.21
Drill with recommended drill
diameter, see above. (Without
pre-drilling in quality Y400 and
Y450).
Low density anchor TLF installed
with Hammer tool TLF-S. Put the
hammer tool into the installation
hole of the low density anchor
and bolt the anchor.
Lower the distance.
Expand the anchor by means of
the Hammer tool.
135
Hammer tool TLF-S
Untreated steel.
For driving in and expansion of the Low density anchor TLF.
Hammer tool TLF-S 12x100
WEF-0001
Part. No. C*
L
mm
Number/
package
Weight kg
100 pcs
781842 6
781843 3
781844 0
180
225
220
1
1
1
23
24
42
Put the Hammer tool into the
Lower the distance.
installation hole of the Low
density anchor and bolt the
fixing (without pre-drilling in quality Y400 and Y450).
Expand the anchor by means of
the Hammer tool.
Sleeve TLF-H12
Hot dip galvanized.
To be used together with Low density anchor TLF 12x100 or 12 x145
in order to raise the transverse force performance.
Sleeve TLF-H12
Part. No. C*
Number/
package
Weight kg
100 pcs
781867 9
25
1.3
Put the sleeve on the Low
density anchor.
(See instructions for Low density
anchor TLF).
136
WEF-0001
Bolt the Low density anchor with
the sleeve in level with the wall.
Adapter TLF-A12
Electro-galvanized.
To be used together with Low density anchor TLF 12x100 or 12x145
in order to receive an interior M10 thread.
Suits Pendant M10.
Adapter TLF-A12
WEF-0007
Part. No. C*
Number/
package
Weight kg
100 pcs
781868 6
10
2.1
Screw the Adapter into the
expanding Low density anchor.
Pendant M10 fits in the Adapter.
Angled bracket TLF-F12
Pre-galvanized.
To be mounted with Low density anchor TLF 12x100 or 12x145
and can be used as fixing for band or wire installations.
Angled bracket TLF-F12
WEF-0001
Part. No. C*
Number/
package
Weight kg
100 pcs
781869 3
25
2.6
Mount the Angled bracket on the
Low density anchor.
(See instructions for Low density
anchor TLF).
Bolt the Low density anchor with
the Angled bracket into the bedding and check that it is secured.
137
Express hanger SVH
For fixing in concrete, natural stone, solid brick or plate.
Used for installation of armatures close to the ceiling (with locking block) as well as
for hanging of integrated ceilings, armatures, electrical-, tube- or ventilating equipment.
Mounting tool SVH-T, for mounting to the right installation depth, is included in the package.
Cover plate is included only for SVH-E1.
Part. No. C*
Express hanger SVH-E1
781870 9
Express hanger SVH-E2**
781871 6
**Cover plate not included.
WEF-0001
Drill
mm
Min. drilling depth
mm
Number/
package
Weight kg
100 pcs
8
8
30
30
100
500
0.3
0.3
Loading
Permitted load capacity at safety factor 3 at extraction
Concrete C25 kN
Solid brick kN
1.0
1.0
0.5
0.5
Hole must be drilled with a 8 mm
drill, drilling depth minimum 30
mm. Drive in the Express hanger
with the Mounting tool SVH-T.
The installation depth always
turns out to be the right.
The short and stiff wire ends grip
effectively into the sides of the
hole resulting in a safe and
strong fixing.
Mounting of wires. Cover plate
hides the hole.
Express hanger SVH can also be
used for installation of Fixing
strip TRB and TGB.
When the fixing strip is turned
into position it self-locks. Can
also be locked with screw, rivet
or lashing wire for extra security.
At a visible installation, hide the
hole with a cover plate. Delivered
together with SVH-E1.
138
Mounting close to the ceiling with
Securing spring SVH-L.
For installation of armatures close to ceiling.
WEF-0001
Part. No. C*
Number/
package
Weight kg
100 pcs
781872 3
25
0.20
For installation of armatures close
to the ceiling. Maximum loading
per securing spring is 4 kg.
Mounting tool SVH-T
Electro-galvanized.
For installation of Express hanger SVH.
Mounting tool SVH-T
WEF-0001
Part. No. C*
Number/
package
Weight kg
100 pcs
781873 0
10
1.8
For installation of Express
hanger SVH. The installation
depth will always turn out to be
the right.
139
Fixing strip TGB
Pre-galvanized.
For pendant installation and clamping
Cold-rolled and galvanized sheet metal, perforated for easy installations.
For fixing tools as Express hanger SVH or Low density anchor TLF with Angled bracket TLF-F12.
Fixing strip TGB 11x0.7
WEF-0001
Part. No. C*
Number/
Package
Weight kg
100 pcs
781874 7
1 (25m)
105
Can be mounted with Express
hanger SVH.
Can be mounted with Low
density anchor TLF and
Angled bracket TLF-F12.
Can easily be mounted with other suitable fixing tools.
Fixing strip TRB
For pendant installation and clamping.
Stainless steel band AISI304 for qualified installations in all type of environments.
Express hanger SVH or Low density anchor TLF with Angled bracket TLF-F12 can be used as fixing tools.
Fixing strip TRB 11x0.7
WEF-0001
Part. No. C*
Number/
package
Weight kg
100 pcs
781875 4
1 (10m)
42
Can be mounted with Express
hanger SVH.
140
Can be mounted with Low
density anchor TLF and
Angled bracket TLF-F12.
Can easily be installed with other suitable fixing tools.
Fixings - Ogebe
The Ogebe fixing is a patented fixing intended for use when mounting plating with a thickness of 0.7-0.9 mm and 13 mm gypsum board.
Pendants, cantilevers and holed strips can be mounted with these fittings.
Technical data
Material
Material treatment
Surface treatment
Maximum load
Cold-rolled sheet steel SS 1142–32
Case-hardened
Electro-galvanized
See load tables
Nut
Bolt
Washer
Locking Nut M8, SMS 2165 FZB
M8 x 16 mm FZB
SRB 13.5 x 26 x 2 mm FZB
ø12 mm
0,7–0,9 mm
Drill a 12 mm dia. hole. A 10 mm
drill can be used if one increases
the hole dia. by slanting the
electric drill.
Place the accompanying washer
over the thin legs. Insert the legs
through the drilled hole and fold
the broader legs towards each
other. If sealing is required, a
standard sealing mass from
building retailers can be used.
Mount the pendant, bracket or
holed strip with the enclosed
bolts and nuts. (The nut should
always be a locking nut).
Breaking load
The load applied at an equi-distance between 2 beams 600 mm apart.
The values are taken from Swedish National Testing Institute Report 8410.0032 1984-09-28.
Fixing type E
Fixing types D, ED
Fixing type Eg
F3
F3
F1
F1
F3
F2
F3
F1
F3
F2
F3
F2
141
Ogebe fixing type E
WEF-0001
The Ogebe fixing type E is used for mounting in 0.7-0.9 mm sheeting or board material.
The following can be mounted: hole straps, pendants, ducts and pipings etc.
Ogebe fixing type E
Electro-galv.
Part. No. C*
Weight kg
100 pcs
716474 5
4.8
Mounting of Pendant rail W32.
Mounting of Pendant rail W32
with Ogebe fixing type E direct
in lighting trunking.
Mounting of Ceiling attachment
W31 on Ogebe fixing type E.
Mounting of hole strap.
Stand installation on wall.
Suspension of duct or pipe.
Mounting of holed beam.
A wire can be mounted directly
in the Ogebe fixing type E.
The Ogebe fixing type E can be
mounted direct into Support
bracket/joint W7.
142
Ogebe fixing type D
WEF-0001
The Ogebe fixing type D is used for mounting in 0.7-0.9 mm sheeting or board material.
The following can be mounted: pendant fittings etc.
Ogebe fixing type D
Electro-galv.
Part. No. C*
Weight kg
100 pcs
716475 2
6.8
Mounting of ceiling attachment
W31 on fixture, type D.
Use Screw set W36 or W36C.
Ogebe fixing type D or ED can
be mounted in lighting trunking
as light fitting.
143
WEF-0001
The Ogebe fixing type ED is used for mounting in 0.7-0.9 mm sheeting or board material.
The following can be mounted: suspension devices, light fittings etc.
Electro-galv.
Part. No. C*
Weight kg
100 pcs
716477 6
5.8
Mounting of Pendant attachment
W21 or Tube pendant attachment W73 with Ogebe fixing type
ED. Use screw set W36/W36C.
When mounting Ceiling attachment W31 on cable trays/lighting
trunking, the load can be distributed onto two or more fixings.
This allow for lateral adjustment.
Mounting of light fittings in plate metal ceiling.
144
Use Screw set W36/W36C.
Installation of holed beam. Use
Screw set W36/W36C.
as light fitting.
WEF-0001
The Ogebe fixing type Eg is intended for mounting in single gypsum boards.
Eg
Electro-galv.
Part. No. C*
Weight kg
100 pcs
716478 3
5.6
Eg mounted in single gypsum
board.
145
Integrated ceilings
Ceilings from Wibe provide undreamt of possibilities to build different types of system ceilings with very high demands on functionality.
You build using reliable, reputable components which are easy to install and combine in an almost neverending number of variations.
146
,
Acoustic lamina
We can supply acoustic lamina for baffle frames, wire baskets and
ceilings with T-profiles.
There are several manufacturers on the market offering lamina of
varying thicknesses, colours, suface coverings and structures.
It is possible to select the colour of your choice
Cable trays, lighting trunking, mounting fittings and accessories
come in standard version in pre-galvaniced or pre-galvanized with
white paint finish (RAL 9010) design in accordance with the Zinkpox method.
A celling often gives a room its character.Exploit the possibilities
The lamina comply with current standardes for fire-protection and
are available with various sound absorption factors.
of choosing a coulor scheme for your ceiling thereby creating a
pleasing atmosphere.
We can supply the whole of our programme in RAL colour of your
choice and with lustre you desire.
147
Open ceilings
4
7
8
3
2
7
3
1
6
9
3
3
5
2
5
3
1
1
Components
1. Cable tray W1
3. Tube pendant attachment W73
4. Pendant strip W33
5. T-joint W9 (alt. W29)
6. Junction box plate W24
7. Screw set W36
8. Screw set W38P
9. Threaded rod M10 W76
148
9
Ceilings with sound baffles
4
8
5
8
7 3
2
10
10
4
8
5
2
10
8
3
10
9
9
9
6
1
1
2
38
1
10
1
6
Components
1. Cable tray W1
4. Ceiling attachment W31
5. Pendant rail W32
7. Screw set W37
8. Screw set W38P
9. Sound baffles
10. Position retainer W43
149
Ceilings with wire baskets
9
4
8
5
3
7
4
1
8
5
3
2
6
10
2 6
10
1
1
Components
1. Cable tray W1
4. Ceiling attachment W31
5. Pendant rail W32
7. Junction box plate W24
8. Screw set W37
9. Screw set W38P
10. Wire baskets
150
4
2
3
7
6
1
5
30
B
1
3
4
5
2
8
1
5
Components
1. Cable trays and Lighting trunking
2. Suspension
3. Junction box plate
4. Support bracket/joint
5. Baffles, baskets etc.
6. W-swing profiles
7. W-swing wall bracket
8. Shade ledges, angle strips, integrated ceiling support channels
and wall trays
B= please state when ordering
151
Sound baffles
Wibe baffle frames are constructed of side and gable sections which are cut to measure
and mounted in accordance with customer requirements.
Baffles with hooks
Baffles with rings
Baffles with hooks
The bottoms of the baffles and trays are on the same level.
Hinged hooks
The hooks allow the baffles to be lowered. However, this necessitates that the space between tray and baffle may not be less then
25 mm.
Clearence hooks
The hooks provide clearence and define the space between tray and
baffle.
Baffles with suspension rings
The rings are adapted to the W-swing profiles used in corridor
installations.
In this type of installation the baffles end up lower than the tray
bottom.
Absorbents
The baffles are provided with optional acoustic lamina. There are
several producers in the market who can offer acoustic lamina in
various thickness, colours and design.
Ordering
When ordering please specify the following measurements:
L = Length of baffle
B = Width of baffle
C = Clearence measurement
Installation with Profile W-sving 2
on Wall bracket W-sving 2.
Suspended baffle.
Installation of suspended baffle
in Profile W-swing 3.
Installation with tray and Profile
W-swing 5. Suspended baffle.
W-swing 1. Suspended baffle.
152
Position retainer
2 Position retainers W43 per baffle must be mounted diagonally.
Mounting
When installing the baffles directly in the trays normally 2 Hinged
hooks are fitted to the one end of the baffles and 2 Clearence hooks
in the other.
At installation without distance between baffle and tray 4 Hinged
hooks must be used.
Material
Made of pre-galvanized sheet steel + powder coated white. Other
colours can be quoted.
Installation of suspended baffle
in Profile W-swing 2 mounted on
Profile W-swing 4A.
Wire baskets
Wire baskets are an alternative to baffles.
They provide an open and airy atmosphere.
In shops and stores they provide good possibilities for
hanging advertisements, bargain offers and decorations.
The grating can be manufactured of wire with different diameters.
Note that the shape of the mesh can either be square or rectangular.
Material
Automatic welding of steel.
Design
The welded grating is aesthetically attractive by simplicity, stability and plasticity.
Abundance of variation due to the mesh pattern 50x50.
Bigger mesh sizes can be offered. Standard pattern 50x50x4 mm.
Ordering
Please state the following
L = Length of basket (mm)
B = Width of basket (mm)
Surface treatment
Powder coated
153
154
Accessories Sound baffles
The following accessories are included in an unassembled sound baffle:
4 Corners, 2 Hinged hooks, 2 Clearence hooks, 2 Side profiles and 2 Gable profiles.
Hinged hooks and clearence hooks can be replaced with suspension rings when necessary.
The baffles are easy to assemble without any tool.
Gable profile
WEF-0001
Gable profile 570
Gable profile 1170
Length
mm
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
570
1170
728802 1
728803 8
13.6
27.9
Side profile
WEF-0001
Side profile for hook
Side profile for suspension ring
Please state length of profile when ordering
Length
mm
Pre-galv.
White30
Part. No. C*
571-625
626-749
750-999
1000-1170
1171-1249
1250-1400
1401-1750
1751-1990
1991-2400
739535 4
739536 1
739537 8
739538 5
739539 2
739540 8
739541 5
739542 2
739543 9
Weight kg
100 pcs
Clearance hook
WEF-0001
Clearance hook 25
Clearance hook 30
Clearance hook 40
Clearance hook 50
Distance between baffle and tray
mm
Electro-galv.
Part. No. C*
Weight kg
100 pcs
25
30
40
50
720252 2
720253 9
720254 6
720255 3
2.0
2.0
2.0
2.0
155
Hinged hook
WEF-0001
Hinged hook 25-30
Hinged hook 40
Hinged hook 50
Distance between baffle and tray
mm
Electro-galv.
Part. No. C*
Weight kg
100 pcs
25-30
40
50
720260 7
720261 4
720262 1
2.0
2.0
2.0
Suspension ring
WEF-0001
Suspension ring 575
Suspension ring 1175
Length
mm
Electro-galv.
Part. No. C*
Weight kg
100 pcs
575
1175
728804 5
728805 2
7
14
Reinforced profile
WEF-0001
Reinforced profile 570
Reinforced profile 1170
Length
mm
White30
Part. No. C*
Weight kg
100 pcs
570
1170
733995 2
733996 9
13.6
27.9
Corner
WEF-0001
Corner
156
Pre-galv
Part. No. C*
Weight kg
100 pcs
720286 7
2.5
Gypsum clip
Used to mount gypsum wallboards in baffle frames.
WEF-0001
Gypsum clip
Steel strip
Part. No. C*
Weight kg
100 pcs
732241 1
0.4
Gypsum boards in Wibes baffle
frames must have dimensions
that are 20 mm smaller than the
size of the baffle. The clip will
keep the board in place.
Lock the gypsum clip by pressing
down the tab.
The gypsum clip suits a
9 mm thick board.
Normally it is enough with 4
gypsum clips pro baffle. The clips
must be mounted diagonally.
Position retainer W43
Support W42
WEF-0017
Two pcs are mounted per baffle.
Support W42
Mounted in T-joint W9 as a support for cables.
Support W42
White plastic
Part. No. C*
Weight kg
100 pcs
718245 9
718214 5
0.4
0.4
Position retainer W43 holds the
sound baffles in the correct
position. W 43 is snapped tight
into the edge of the cable tray or
lighting trunking.
Support W42 is mounted at
T-joint W9 to prevent the cables
from gliding out over the corner
of the cable tray or lighting
trunking. W42 is snapped tight
into the edge of the tray.
157
Frame clip W90
Enables clip mounting in baffle frame.
Frame clip W90 (screw RXS Combi B6x19, fzb)
WEF-0001
Pre-galv.
Part. No. C*
Weight kg
100 pcs
723021 1
1.0
Mounting of decoration strip etc.
The Frame clip W90 is clamped
tight under the edge of the
section.
Mounting of light fittings on
Reinforced profile.
Installation of air component.
T-section is easily mounted with
Frame clips W90 in the baffle
frames.
In large frames an extra support
for the absorbent lamina can be
required. Install a T-section with
2 Frame clips W90.
Light fitting mounted in baffle frame.
2 T-profiles mounted with 4 Frame clips W90.
158
159
Profile W-swing 1/40
A profile that will simplify service and maintenance, used for mounting on trays with edge height 40 mm.
600 mm c/c is standard. Other c/c measurements can be manufactured on request.
Profile W-swing 1
WEF-0001
White30
Part. No. C*
Weight kg
100 pcs
729196 0
210
Installation with tray on both sides and Profile W-swing 1 hanging on tray
Installation with tray and Profile W-swing 1. Suspended baffles,
edge. Suspended baffle, folding in both directions.
folding in both directions. The trays have pendular suspension from ceiling.
A profile that will simplify service and maintenance, used for mounting on trays with edge height 60 mm.
WEF-0001
White30
Part. No. C*
Weight kg
100 pcs
786871 1
200
Installation with tray on both sides and Profile W-swing 1 hanging on tray
Installation with tray and Profile W-swing 1. Suspended baffles, folding in
edge. Suspended baffle, folding in both directions.
both directions. The trays have pendular suspension from ceiling.
160
Profile W-swing 2
A profile that will simplify service and maintenance.
Profile W-swing 2
WEF-0001
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
728866 3
730162 1
110
Installation with Profile W-swing 2 on Wall bracket W-swing 2.
Suspended baffle, folding in both directions.
Ceiling installation with Profile W-swing 2. Suspended baffle, folding
in both directions.
When joining, Ceiling bracket
W31 can be both joint and ceiling
bracket. Mounted with Screw set
W34.
Profile W-swing 2 can be
suspended in Pendant strip W33.
Mounted with Screw set W34.
suspended in Pendant attachment W21. Mounted with Screw
set W34.
161
Wall bracket W-swing 2
WEF-0001
Used for installation with Profile W-swing 2.
Wall bracket W-swing 2
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
721175 3
729067 3
16
Wall bracket W-swing 2 mounted on pendant or direct on wall.
162
Profile W-swing 2 mounted on
Wall bracket W-swing 2 with
Screw set W34. The profile can
easily be adjusted in the oval
holes of the wall bracket and the
profile. Infinitely variable lengthwise and ± 20 mm towards wall.
Profile W-swing 3
WEF-0001
Profile W-swing 3
White30
Part. No. C*
Weight kg
100 pcs
729198 4
277
Installation with tray and Profile W-swing 1, Wall bracket W-swing 2
with Profile W-swing 2 and pendant with Profile W-swing 3.
Hanging baffles, folding in both directions
W34.
suspended in Pendant attachment W21. Mounted with Screw
set W34.
suspended in Pendant strip W33.
Mounted with Screw set W34.
163
Profile W-swing 4A
WEF-0001
Profile W-swing 4A
White30
Part. No. C*
Weight kg
100 pcs
731618 2
150
For suspension of baffles,
Profile W-swing 4A is used
in combination with Profile
W-swing 2. Mounted with Screw
set W34.
Profiles W-swing 2 och W-swing W-swing 4A can be suspended
4A mounted with Screw set W34. in Pendant attachment W21.
W-swing 4A can be suspended
in Pendant strip W33.
W34.
164
Profile W-swing 5
WEF-0001
White30
Part. No. C*
Weight kg
100 pcs
729200 4
200
Profile W-swing 5
W-swing 5. Baffle in level with tray
and folding in both directions.
Shade ledge W26/40
Used as a support for ceilings mounted between cable trays with edge height 40 mm.
Shade ledge W26/40
WEF-0001
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
1.0
717990 9
729192 2
154
Shade ledge W26/40 is hung
over the side edge of the cable
tray.
Shade edge W26/40 is used as a
support for ceilings mounted
between cable trays. Also suitable for Lighting trunking W70/
W71. Mounted along the side
edges of the cable tray or the
lighting trunking.
Shade list W26/40 is locked tight
in the tray by pinching the ends
in under the tray edge with pliers.
165
Shade ledge W26/60
Shade edge W26/60
WEF-0001
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
1.0
718559 7
782661 2
185
Shade ledge W26/60 is hung
over the side edge of the cable
tray.
Shade edge W26/60 is used as a
support for ceilings mounted
between cable trays.
Mounted along the side edges of
the cable tray.
Shade list W26/60 is locked tight
in the tray by pinching the ends
in under the tray edge with pliers.
Integrated ceiling support channel
W27/40
Integrated ceiling support channel W27/40
WEF-0001
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
1.0
714008 4
729193 9
130
Integrated ceiling support
channel W27/40 is hung over
and mounted along the side
edge of the cable tray and
is used as a support for ceilings mounted between cable
trays. Also suitable for Lighting
trunking W70/W71.
166
W27/40 is locked tight in the tray
by pinching the ends in under the
tray edge with pliers.
W27/60
WEF-0001
Plate
thickness
mm
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
1.0
718556 6
782662 9
160
Integrated ceiling support channel W27/60
W27/60 is used as a support for
ceilings mounted between cable
trays. Mounted along the side
edge of the cable tray.
W27/60 is locked tight in the tray
by pinching the ends in under the
tray edge with pliers.
Angle strip W46
Used as a support for ceiling installations.
Plate
thickness
mm
Angle strip W46
0.6
WEF-0001
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
718608 2
729194 6
52
Angle strip W46 is mounted
directly onto wall, column or
similar as a support for baffles or
ceiling lamina.
167
Wall tray W60/40
Wall tray with edge height 60 mm used for mounting of ceiling in corridor.
The tray is mounted directly onto the wall.
L
mm
Wall tray W60/40
2000
WEF-0001
Pre-galv.
Part. No. C*
Pre-galv. White30
Part. No. C*
Weight kg
100 pcs
718383 8
729195 3
135
Wall tray W60 is mounted directly
onto the wall.
Mounting of ceiling in corridor when canalisation on one side is
required but with the same functionality as for cable trays on both
sides.
Wall tray W60/60
Wall tray with edge height 60 mm used for mounting of ceiling in corridor.
The tray is mounted directly onto the wall.
Plate
thickness
mm
Wall tray W60/60
1.0
WEF-0001
Pre-galv.
Part. No. C*
Pre-galv.
White30
Part. No. C*
Weight kg
100 pcs
787182 7
782783 1
333
Wall tray W60/60 is mounted
directly onto the wall.
168
Mounting of ceiling in corridor when canalisation on one side is
required but with the same functionality as for cable trays on both
sides.
Use Vertical piece 2F at installa- Example of corridor installation. This way of mounting reduce the
tions in corridors with gypsum
obliquity of the cable tray.
walls. The installation can easily
be adjusted both vertically and
horizontally and will not be
effected of vibrations in the walls.
Example of installation with uneven loadings. The installation has
been reinforced with lashing wires. The wire can be fixed to the ceiling or the ceiling bracket.
Internal cantilever arm can be
mounted right over support
bracket/joint.
Mounting of Pendant rail W32
with Ogebe fixing type E direct in
lighting trunking.
as light fitting.
The Ogebe fixing type E can be
mounted direct into Support
bracket/joint W7.
169
170
171
172
Management system - Quality and Environment
Wibe has a third-party certified management system for
quality and environment in accordance with ISO 9001:2000
and ISO 14001:2004
AB WIBE
Box 401, SE-792 27 MORA, Sweden
Telephone +46 250 280 00, Telefax +46 250 188 55
e-mail: info@wibe.se, www.wibe.se

Cable Trays and Integrated Ceilings

Transcription

Similar documents

CVJM-Informationen 4

DECORUM Indoor Collection

entire Catalog in PDF format

Anchor Systems

Z400 Z Master

rema tip top automotive programme - 2015/2016

Anchor Systems

alfresco collection