Sleeved Plug Valves

Transcription

Sleeved Plug Valves

SLEEVED PLUG VALVES
6418, Trans-Canada Highway W., Montreal, (Qc), Canada H4T 1X4
Tel.: (514) 739-0220 • Fax: (514) 739-5452
1-888-269-0220
e-mail: info@fluorosealvalves.com
www.fluorosealvalves.com
AV-102004 PRINTED IN CANADA
FLUOROSEAL INC.
WARRANTY TERMS & CONDITIONS
PLUG VALVES
CONTROLLING PROVISIONS:
9
These terms and conditions shall control
with respect to any purchase order or
sale of Fluoroseal's products. No waiver,
alteration or modification of these terms
and conditions whether on Buyer's purchase order or otherwise, shall be valid
unless the waiver, alteration or modification is specifically accepted in writing
and signed by an authorized representative of Fluoroseal Inc.
4
2
3
10
5
1
6
8
7
Design Features Summary
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Bi-directional inline bubble tight seal independent of line pressure.
Multiple external bubble tight seals independent of line pressure.
Direct mechanical three point adjustment independent of line pressure.
Independent travel stops.
Full encapsulation and retention of all leading edges of PTFE sleeve and
top seal components.
Full lip at port openings protects PTFE sleeve.
Contoured waterway assures minimum flow turbulence characteristic.
No body cavities to entrap flow media.
Positive flow direction indication.
Drilled and tapped flange mounting pads independent of cover and top
seal assembly.
Other Features
-
Bi-directional flow.
Quarter turn operation
Nonlubricated
Self-cleaning on each operation.
Two way and multiport configurations
Special service and jacketed designs available.
All casting components traceable to mill test certificates.
Investment cast on all materials for sizes 1/2" - 10" (Class 150)
Investment cast on all materials for sizes 1/2" – 6" (Class 300)
Castings meet level 1 casting specifications
Heavy duty gears are standard on all our valves
DELIVERY: Fluoroseal Inc. will make
every effort to complete delivery of
products as indicated on its acceptance
of an order, but Fluoroseal assumes no
responsibility or liability, and will
accept no backcharge, for loss or damage due to delay or inability to deliver
caused by acts of God, war, labor difficulties, accident, delays of carriers, by
contractors or suppliers, inability to
obtain materials, shortages of fuel and
energy, or any other causes of any kind
whatever beyond the control of
Fluoroseal Inc. Fluoroseal may terminate any contract of sale of its products
without liability of any nature, by written notice to Buyer, in the event that
the delay in delivery or performance
resulting from any of the aforesaid
causes shall continue for a period of
sixty (60) days. Under no circumstances
shall Fluoroseal Inc. be liable for any
special or consequential damages or
for loss, damage, or expense (whether
or not based on negligence) directly or
indirectly arising from delays or failure
to give notice of delay.
WARRANTY: Fluoroseal Inc. warrants
for one year from the date of shipment
of its manufactured products to the
extent that Fluoroseal will replace
those having defects in material or
workmanship when used for the purpose and in the manner which
Fluoroseal recommends. If Fluoroseal’s
examination shall disclose to its satisfaction that the products are defective,
and an adjustment is required, the
amount of such adjustment shall not
exceed the net sale price of the defective product(s) only and no allowance
will be made for labor or expen-se for
repairing or replacing defective products or workmanship or damage resulting from the same. Fluoroseal Inc. warrants the products which it sells of
other manufacturers to the extent of
the warranties of their respective makers. Where engineering design or fabrication work is supplied.
Buyer's
acceptance of Fluoroseal's design or of
delivery of work shall relieve Fluoroseal
Inc. of all further obligation, other
than expressed in Fluoroseal's product
warranty.
THIS IS FLUOROSEAL'S INC SOLE WARRANTY. FLUOROSEAL INC. MAKES NO
OTHER WARRANTY OF ANY KIND,
EXPRESSED OR IMPLIED, AND ALL
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE WHICH EXCEED
THE AFORESTATED OBLIGATION ARE
HEREBY DISCLAIMED BY FLUOROSEAL
INC AND EXCLUDED FROM THIS WARRANTY.
Fluoroseal Inc. neither assumes, nor
authorizes any person to assume for it,
any other obligation in connection with
the sale of its engineering designs or
products. This warranty shall not apply
to any products or parts of products
which (a) have been repaired or altered
outside of Fluoroseal's factory, in any
manner; (b) have been subjected to
misuse, negligence or accidents; (c)
have been used in a manner contrary to
Fluoroseal's instructions or recommendations. Fluoroseal Inc. shall not be
responsible for design errors due to
inaccurate or incomplete information
supplied by Buyer or its representatives.
FLUOROSEAL'S LIABILITY: Fluoroseal
Inc. will not be liable for any loss, damage, cost of repairs, incidental or consequential damages of any kind,
whether based upon warranty (except
for the obligation accepted by
Fluoroseal Inc. under "Warranty"
above), contract or negligence, arising
in connection with the design, manufacture, sale, use or repair of the products or of the engineering designs
supplied to Buyer.
RETURNS: Fluoroseal Inc. cannot accept
return of any product(s) unless its written permission has been first obtained,
in which case same will be credited
subject to the following: (a) All material returned must, on its arrival at
Fluoroseal's plant, be found to be in
first-class condition; if not, cost of putting in saleable condition will be
deducted from credit memoranda; (b)
A handling charge deduction of twenty percent (20%) will be made from all
credit memoranda issued for material
returned; (c) Transportation charges, if
not prepaid, will be deducted from
credit memoranda.
SHIPMENTS: All products sent out will
be carefully examined, counted and
packed. The cost of any special packing or special handling caused buy
Buyer's requirements or requests shall
be added to the amount of the order.
No claim for shortages will be allowed
unless made in writing within ten (10)
days of receipt of a shipment. Claims
for products damaged or lost in transit
should be made to the carrier, as
Fluoroseal's responsibility ceases, and
title passes, on delivery to the carrier.
SPECIAL PRODUCTS: Orders covering
special or non-standard products are
not subject to cancellation except on
such terms as Fluoroseal Inc. may specify on application.
PRICES AND DESIGNS: Prices and
designs are subject to change without
notice. All prices are F.O.B. Point of
Shipment, unless otherwise stated.
TAXES: The amount of any sales, excise
or other taxes, if any, applicable to the
products, shall be added to the purchase price and shall be paid by Buyer
unless Buyer provides Fluoroseal Inc.
with an exemption certificate acceptable to the taxing authorities.
NUCLEAR PLANTS: Where the products, engineering design or fabrication
is for nuclear plant applications. Buyer
agrees (a) to take all necessary steps to
add Fluoroseal Inc. as an insured under
the American Nuclear Insurers' (ANI)
pool and under the Mutual Atomic
Energy Reinsurance Pool (MAERP) for
property damage and liability insurance and if necessary steps could have
been taken, but are not taken, Buyer
shall hold Fluoroseal Inc. harmless
against all such losses which could
have been thus covered (b) Buyer
agrees to hold Fluoroseal Inc. harmless
with respect to any personal injury or
death, property damage or any other
loss in a nuclear incident which is
caused directly or indirectly by defective design, material, or workmanship,
furnished by Fluoroseal Inc. and which
is covered by insurance maintained by
Buyer (or which could be so covered
but with respect to which Buyer has
elected to self-insure), and further
agrees to waive subrogation by its carriers of such insurance against
Fluoroseal Inc., and (c) as to nuclear
hazards for which Buyer cannot obtain
insurance coverage, the liability of
Fluoroseal Inc. for any personal injury
or death, property damage or any
other loss directly caused by defective
design, material, or workmanship furnished by Fluoroseal Inc. shall not
exceed the value of the material furnished by Fluoroseal Inc. at the time of
the loss occurrence.
MINIMUM INVOICE: $100 plus shipping.
TERMS: Cash, net 30 days unless
otherwise specified.
DESIGN FEATURES
Design Features
FluoroSeal®, Nonlubricated, Sleeved Plug Valves possess the state-of-the-art in PTFE fluorocarbon seated
designs. With little or no maintenance and trouble free operation, a high integrity bubble tight seal is provided both inline and to atmosphere. The specific design features contributing to the superiority of this product
are described, as a function of their individual purpose and engineering precautions taken to assure maximum
service life.
PTFE fluorocarbon, utilized in the FluoroSeal sleeve and top seal components, is universally corrosion resistant
being inert to all but a few rarely encountered chemicals. It is thermoplastic that can be used at a continuous
service temperature of 400°F (204°C) and much higher temperatures can be satisfactorily sustained for shorter
periods. Having a very low coefficient of friction it is self-lubricating negating the need for any other lubrication. Since PTFE is susceptible to deformation as it is put under load and to cold flow, as it becomes more pliable at elevated temperatures, precaution must be taken to control this activity to the advantage of the intended purpose of the valve.
The FluoroSeal internal body configuration has been designed to totally contain all of the leading edges of the
PTFE sleeve at the top, at the bottom and around the entire port opening adjacent to the waterway. Any tendency the sleeve has to grow is accommodated by relief areas, designed for this purpose, positioned at 90
degrees to the body port openings, The port defining metal lips protects the PTFE sleeve from erosion and any
possibility of sleeve rotation within the body.
The waterway in the body has been designed with a contour providing a flow path that assures a minimum flow
turbulence characteristic. The critical sealing areas circumferentially around the top and bottom of the sleeve
and around the body port openings are maintained by means of an adjustable tapered plug compressing the
PTFE sleeve over raised ribs.
The PTFE top seal components are similarly contained and protected from damage. A counter bore is provided
at the top of the metal body to encapsulate the outside diameter of the formed PTFE diaphragm in conjunction
with the formed metal diaphragm and to protect it from rupturing by regulating the amount of compression at
this point. The inside diameter of the formed PTFE diaphragm, adjacent to the plug stem, is also contained by
means of a unique lip design of the formed metal diaphragm preventing extrusion and maintaining the stem
seal throughout variable service conditions. This unique formed metal diaphragm also provides a positive electrical ground between the plug and body eliminating the need for an extra component to fulfill this function
as in the case of other valve manufacturers’ designs.
Three point external adjusting bolts in the cover assures equilibrium to the compression of the stem and inline
seals by imparting a balanced force through a metal thrust washer located under the cover above the formed
metal diaphragm. This mechanism provides a multiple seal to atmosphere and a double (downstream &
upstream) bi-directional inline seal.
Independent wrench stops are cast on the cover to limit the stroke at the open and close positions without
endangering the integrity of the seal adjustment as in other manufacturers’ designs. Parallel flats are machined
on the sides of the plug stem providing positive indication of the direction of flow at all time, independent of
other position indicators.
All major pressure containing components, body, plug and cover, of FluoroSeal valves, are fully traceable to mill
test certificates assuring material authenticity. Quality levels are maintained through continual inspection and
manufacturing surveillance of these and all other components. A concerted effort is made to conform to all regulatory authority requirements as where and when invoked, in keeping with FluoroSeal’s pledge of quality first.
1
VALVE COMPONENTS
WRENCH
ADJUSTING
BOLT
COVER
COVER BOLTS
THRUST WASHER
COMBINATION
FORMED METAL
DIAPHRAGM AND
STATIC ELIMINATOR
PTFE DELTA RING
COMBINATION
PTFE DIAPRRAGN AND
STEM SEAL COLLAR
MATERIALS OF CONSTRUCTION
Body and Plug1
Cover2
Cover Bolts2
Adjusting Bolts
Thrust Washer
Metal Diaphragm3
Delta Ring
Diaphragm
Sleeve4
Wrench Operator5
Wrench Bolt5
Gear Assembly
Gear Adaptor5
Gear Mounting Bracket
Mounting Bracket Bolts5
As specified
Carbon Steel, 304 SS
Steel, 304 SS
304 SS
304 SS
304 SS, Monel
PTFE Fluorocarbon
PTFE Fluorocarbon
PTFE Fluorocarbon
Carbon Steel
Steel
Cast Steel Housing
Steel
304 SS
Steel
PLUG
PTFE SLEEVE
1. See "Technical Data" for material selections.
2. Cover and bolt materials of standard valves will be supplied in accordance with
the following table:
SPECIFIED BODY MATERIAL
Ductile Iron
Carbon Steel
All other materials
COVER MATERIAL
Carbon Steel
Carbon Steel
CF 8
COVER BOLT MATERIAL
ASTM A-193 GR. B7
ASTM A-193 GR. B7
ASTM A-193 GR. B8
3. Monel metal diaphragms will be supplied with valves having a monel or nickel
body or plug. All others will be supplied with 304 SS diaphragms.
4. Glass reinforced PTFE, PFA Fluorocarbon and UHMWPE sleeves are available on
special order.
5. 304 SS Available on special order.
BODY
2
2-WAY VALVES - DIMENSIONAL DATA
CLASS 150 LBS
Flanged Ends
Wrench Operated
(EG) Enclosed Gear Operated
Actuators optional on all sizes
Fig. R152F
DIMENSIONS TO ANSI B16.5 & B.16.10
SIZE
L
H
D
K
G
B
F
D
Q
N
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm. NO.
1/2”
4.25
108.0
3.38
86
3.50
88.9
2.38
60.5
1.38
35.0
0.37
9.5
0.06
1.6
0.63
16.0
8.00
203
3/4”
4.63
117.5
3.38
86
3.88
98.5
2.75
69.9
1.68
42.9
0.37
9.5
0.06
1.6
0.63
16.0
8.00
1”
5.00
127.0
4.50
114
4.25
108.0
3.13
79.5
2.00
50.8
0.44
11.2
0.06
1.6
0.63
16.0
1-1/2”
6.50
165.1
5.31
135
5.00
127.0
3.88
98.6
2.88
73.2
0.56
14.2
0.06
1.6
0.63
2”
7.00
177.8
6.25
159
6.00
152.4
4.75
120.7
3.63
92.0
0.63
16.0
0.06
1.6
0.75
*2-1/2” 8.00
203.2
6.56
167
7.50
190.5
5.50
139.7
4.13
104.6
0.75
19.0
0.06
1.6
WT’S
(kg.)
(lbs.)
4
2.3
5
203
4
2.7
6
9.00
229
4
3.6
8
16.0
14.25
362
4
6.4
14
19.0
16.50
419
4
10.5
23
0.75
19.0
16.50
419
4
16.4
36
419
4
16.4
36
3”
8.00
203.2
6.56
167
7.50
190.5
6.00
152.4
5.00
127.0
0.75
19.0
0.06
1.6
0.75
19.0
16.50
4”
9.00
228.6
7.63
194
9.00
228.6
7.50
190.5
6.19
157.2
0.94
23.9
0.06
1.6
0.75
19.0
23.63
600
8
26.8
59
4” EG
9.00
228.6
9.10
231
9.00
228.6
7.50
190.5
6.19
157.2
0.94
23.9
0.06
1.6
0.75
19.0
7.25
184
8
35.9
79
6”
10.50
266.7 10.80 274
11.00
279.4
9.50
241.3
8.50
215.9
1.00
25.4
0.06
1.6
0.88
22.4
7.25
184
8
55.5
122
8”
11.50
292.1 12.75 324
13.50
342.9 11.75 298.5
10.63
269.8
1.13
28.7
0.06
1.6
0.88
22.4
9.75
248
81
100.0
220
10”
13.00
330.2 14.68 373
16.00
406.4 14.25 362.0
12.75
323.9
1.19
30.2
0.06
1.6
1.00
25.4
9.75
248
122
150.0
330
12”
14.00
355.6 16.40 417
19.00
482.6 17.00 431.8
15.00
381.0
1.25
31.8
0.06
1.6
1.00
25.4
10.00
254
122
198.6
437
14”
15.00
381.0 17.40 442
21.00
533.4 18.75 476.3
16.25
412.8
1.38
35.1
0.06
1.6
1.12
28.4
10.00
254
123
295.0
650
Dimensions for sizes larger than 14” available on request
*21/2” valves are made from 3” casting, but flanges are machined to 21/2” dimensions
N= Number of holes
(1) 2 top holes in flanges are tapped for 3/4” - 10 UNC Threads
(3) 2 top holes in flanges are tapped for 1" -8 UNC Threads
CLASS 300 LBS
Flanged Ends
Wrench Operated
Fig. R302F
SIZE
L
H
D
K
G
B
F
D
Q
N
WT'S
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm.
NO.
(kg)
(lbs.)
1/2"
5.5
139.7
3.38
86
3.75
95.3
2.63
66.8
1.38
35
0.56
14.2
0.06
1.6
0.63
16
8
203
4
3.2
7
3/4"
6
152.4
3.38
86
4.63
117.6
3.25
82.6
1.69
42.7
0.63
16
0.06
1.6
0.75
19
8
203
4
4.1
9
1"
6.5
165.1
4.5
114
4.88
124
3.5
88.9
2
50.8
0.69
17.5
0.06
1.6
0.75
19
9
229
4
5.5
12
1-1/2"
7.5
190.5
5.31
135
6.13
155.7
4.5
114.3
2.88
73.2
0.81
20.6
0.06
1.6
0.88
22.4
14.25
362
4
9.5
21
2"
8.5
215.9
6.25
159
6.5
165.1
5
127
3.63
92
0.88
22.4
0.06
1.6
0.75
19
16.5
419
8
13.2
29
*2-1/2" 11.13 282.7
3"
11.13 282.7
6.56
167
8.25
209.6
5.88
149.4
4.13
104.6
1.13
28.7
0.06
1.6
0.88
22.4
16.5
419
8
21.8
48
6.56
167
8.25
209.6
6.63
168.4
5
127
1.13
28.7
0.06
1.6
0.88
22.4
16.5
419
8
21.8
48
4"
12
304.8
7.53
191
10
254
7.88
200.2
6.19
157.2
1.25
31.8
0.06
1.6
0.88
22.4
23.63
600
8
42
92
4" EG
12
304.8
9.1
231
10
254
7.88
200.2
6.19
157.2
1.25
31.8
0.06
1.6
0.88
22.4
7.25
184
8
54
119
8.5
201
6"
15.88 403.4
10.8
274
12.5
8"
16.5 419.1
12.75
324
15
14.68
373
17.5
16.4
417
20.5
520.7 17.75 450.9
17.4
442
23
584.2 20.25 514.4
10"
12"
14"
18
457.2
19.75 501.7
30
762
317.5 10.63
215.9
1.44
36.6
0.06
1.6
0.88
22.4
7.25
184
12
91.4
330.2
10.63 269.8
1.63
41.4
0.06
1.6
1
25.4
9.75
248
12
141.4
311
444.5 15.25 387.4
12.75 323.9
1.88
47.8
0.06
1.6
1.13
28.7
9.75
248
16
210.9
464
381
13
270
15
381
16.25 412.8
2
50.8
0.06
1.6
1.25
31.8
10
254
16
279
614
2.12
53.8
0.06
1.6
1.25
31.8
10
254
20
363
800
N= Number of holes
3
Fig. R152/302 SE
CLASS 150/300
Screwed Ends
Wrench Operated
Actuators optional
DIMENSIONS TO ANSI B.16.11
SIZE
L
H
Q
Wt's
in.
mm.
in.
mm.
in.
mm.
(kg)
(lbs.)
1/2"
3.93
100
3.38
86
8
203
2
4.4
3/4"
3.93
100
3.38
86
8
203
2
4.4
1"
5.5
140
4.5
114
9
229
3
6.6
1-1/2"
6.3
160
5.31
135
14.25
362
6
13.2
2"
7.87
200
6.25
159
16.5
419
10
22
Fig. R152/302 SW
CLASS 150/300
Socketweld Ends
Wrench Operated
Actuators optional
SIZE
4
L
H
D
J
F
Q
Wt's
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm.
(kg)
(lbs.)
1/2"
3.93
100
3.38
86
0.85
21.6
0.55
14
0.37
9.5
8
203
2
4.4
3/4"
3.93
100
3.38
86
1.07
27.2
0.75
19
0.5
12.7
8
203
2
4.4
1"
5.5
140
4.5
114
1.34
34
0.98
25
0.5
12.7
9
229
3
6.6
1-1/2"
6.3
160
5.31
135
1.92
48.8
1.5
38
0.5
12.7 14.25
362
6
13.2
2"
7.87
200
6.25
159
2.4
61
1.97
50
0.66
16.7
419
10
22
16.5
CLASS 600
Refer to size range availability for
selection, available in all materials,
except ductile iron.
CLASS 600 LBS
Flanged Ends
Wrench Operated
Fig. R602 F
CLASS600
600DIMENSIONS
DIMENSIONS
CLASS
L
H
D
K
g
SIZE
600#
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm.
1/2"
3/4"
1"
1-1/2"
2"
2-1/2"
3"
4"
4" EG
6"
8"
10"
12"
6.50
7.50
8.50
9.50
11.50
13.00
14.00
17.00
17.00
22.00
26.00
31.00
33.00
165.1
190.5
215.9
241.3
292.1
330.2
355.6
431.8
431.8
558.8
660.4
787.4
838.2
3.38
3.38
4.50
5.31
6.25
6.56
6.56
7.53
9.10
10.80
12.75
14.68
16.40
85.7
85.9
114.3
134.9
158.8
166.6
166.6
191.1
231.1
274.3
323.9
372.9
416.6
3.75
4.62
4.88
6.12
6.50
7.50
8.25
10.75
10.75
14.00
16.50
20.00
22.00
95.3
117.3
124.0
155.4
165.1
190.5
209.6
273.1
273.1
355.6
419.1
508.0
558.8
2.62
3.25
3.50
4.50
5.00
5.88
6.62
8.50
8.50
11.50
13.75
17.00
19.25
66.5
82.6
88.9
114.3
127.0
149.4
168.1
215.9
215.9
292.1
349.3
431.8
489.0
1.38
1.69
2.00
2.88
3.62
4.12
5.00
6.19
6.19
8.50
10.62
12.75
15.00
35.1
42.9
50.8
73.2
91.9
104.6
127.0
157.2
157.2
215.9
269.7
323.9
381.0
CLASS
CLASS600
600DIMENSIONS
DIMENSIONS
b
f
d
Q
Wt's
SIZE
600#
in.
mm.
in.
mm.
in.
mm.
in.
mm.
N
NO.
(kg)
(lbs.)
1/2"
3/4"
1"
1-1/2"
2"
2-1/2"
3"
4"
4" EG
6"
8"
10"
12"
0.56
0.62
0.69
0.88
1.00
1.12
1.25
1.50
1.50
1.88
2.19
2.50
2.62
14.2
15.7
17.5
22.4
25.4
28.4
31.8
38.1
38.1
47.8
55.6
63.5
66.5
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
0.25
6.4
6.4
6.4
6.4
6.4
6.4
6.4
6.4
6.4
6.4
6.4
6.4
6.4
0.62
0.75
0.75
0.88
0.75
0.88
0.88
1.00
1.00
1.12
1.25
1.38
1.38
15.7
19.1
19.1
22.4
19.1
22.4
22.4
25.4
25.4
28.4
31.8
35.1
35.1
8.00
8.00
9.00
14.25
16.50
16.50
16.50
23.63
7.25
7.25
9.75
9.75
13.75
203.2
203.2
228.6
362.0
419.1
419.1
419.1
600.2
184.2
184.2
247.7
247.7
349.3
4
4
4
4
8
8
8
8
8
12
12
16
20
3.6
5.0
7.3
12.3
18.2
N/A
38.6
68.2
81.8
152.3
222.7
N/A
N/A
8
11
16
27
40
N/A
85
150
180
335
490
N/A
N/A
N= Number of holes
5
FULL PORT PLUG VALVES
You like the design features of
our standard port valves, but
you are concerned about
flow restrictions?
N o w, y o u h a v e t h e b e s t
of two worlds:
FluoroSeal proven design combined with non-restricted flow.
Now, you have the choice.
The new F Series, is available in:
Classes 150, 300 and 600 lbs.
Size range from 1” to 8”.
Same material offering as our
standard valves.
Fig. F152 F
Fig. F302 F
FluoroSeal proven
design
now combined
with
non-restricted flow
CLASS 150 / 300 LBS
Flanged Ends
Wrench Operated
DIMENSIONS
FULL PORT DIMENSIONS
SIZE
150&
300#
L
in.
H
mm.
in.
3.38
1/2" (150#)
4.25
108.0
3.38
1/2" (300#)
5.50
139.7
N/A
3/4"
6.00
152.4
1"
6.50
165.1
5.06
1-1/2"
7.50
190.5
5.81
9.25
2"
8.50
215.9
9.25
3"
11.13
282.7
11.00
4"
12.00
304.8
6"
22.00
558.8
N/A
8"
27.00
685.8
17.81
NOTE:
1- Class
600 dimensions
available
on request.
Class 600
dimensions
available on
request.
Available
DIN valves.
2- Available
DIN valves.
D
K (150#)
K (300#)
mm.
in.
mm.
in.
mm.
85.9
85.9
N/A
128.6
147.5
235.0
235.0
279.4
N/A
452.5
3.50
3.75
3.75
4.88
6.12
6.50
8.25
10.00
12.50
15.00
88.9
95.3
95.3
124.0
155.4
165.1
209.6
254.0
317.5
381.0
2.38
60.5
2.75
3.12
3.88
4.75
6.00
7.50
9.50
11.75
69.9
79.2
98.6
120.7
152.4
190.5
241.3
298.5
in
2.62
3.25
3.50
4.50
5.00
6.62
7.88
10.62
13.00
g
mm.
in.
mm.
66.5
82.6
88.9
114.3
127.0
168.1
200.2
269.7
330.2
1.38
1.38
1.69
2.00
2.88
3.62
5.00
6.19
8.50
10.62
35.1
35.1
42.9
50.8
73.2
91.9
127.0
157.2
215.9
269.7
N (150#)
N (300#)
NO.
(kg.)
(lbs.)
4
4
4
4
8
8
8
12
12
2.3
3.2
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
5
7
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
FULL PORT DIMENSIONS
DIMENSIONS
SIZE
150&
300#
b
in.
f
mm.
in.
1/2" (150#)
0.37
9.4
0.06
1/2" (300#)
0.56
14.2
0.06
3/4"
0.62
15.7
0.06
1"
0.69
17.5
0.06
1-1/2"
0.81
20.6
0.06
2"
0.88
22.4
0.06
3"
1.12
28.4
0.06
4"
1.25
31.8
0.06
6"
1.44
36.6
0.06
8"
1.62
41.1
0.06
NOTE:
1- Class
600 dimensions
available
on request.
Class 600
dimensions
available on
request.
Available
DIN valves.
2- Available
DIN valves.
N= Number of holes
6
d (150#)
mm.
in.
mm.
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
1.6
0.62
15.7
0.62
0.62
0.62
0.75
0.75
0.75
0.88
0.88
15.7
15.7
15.7
19.1
19.1
19.1
22.4
22.4
d (300#)
in.
0.62
0.75
0.75
0.88
0.75
0.88
0.88
0.88
1.00
Q
mm.
in.
mm.
NO.
203
203
N/A
362
419
600
600
248
N/A
349
4
15.7
19.1
19.1
22.4
19.1
22.4
22.4
22.4
25.4
8.00
8.00
N/A
14.25
16.50
23.63
23.63
9.75
N/A
13.75
4
4
4
4
4
8
8
8
Wt's
3 WAY & MULTIPORT
3-WAY VALVES
Flow arrangements:
Flow is indicated by the arrow.
When rotating plugs FA2, FA3 or FA4 a transflow condition exists at all times.
Only position B in plugs FA1 And FA5 will provide a shut off condition.
Valves will be supplied with 900 operators as standard, should 1800 operator be
needed, please specify.
PLUG TYPE
FA1
Position A
00
Position B
900
Position C
1800
8
FA2
FA3
FA4
FA5
CLASS 150 LBS
Flanged Ends
Wrench Operated
Fig. R153 F
SIZE
L
in.
H
D
K
g
b
f
d
Q
G
N
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
108
3.38
86
3.5
88.9
2.38
60.4
1.38
35
0.37
9.5
0.06
1.6
0.63
16
8
203
2.75
70
3/4" 4.63 117.8 3.38
86
3.88 98.5
2.75
69.8
1.68
42.7
0.37
9.5
0.06
1.6
0.63
16
8
203
2.88
4.5
114
4.25 108
3.13
79.5
2
50.8
0.44
11.2
0.06
1.6
0.63
16
9
229
3.5
3.88
1/2" 4.25
1"
5
127
*1-1/2" 6.5
165.1 5.31
135
5
127
2"
7
177.8 6.25
159
6
152.4
*2-1/2"
8
203.2 6.56
167
3"
8
203.2 6.56
167
4"
9
228.6 7.63
194
9
228.6
4" EG
mm. NO.
Wt's
(kg.)
(lbs.)
4
2.5
6
73.2
4
3.2
7
88.9
4
5
11
98.6
2.88
73.2
0.56
14.3
0.06
1.6
0.63
16
14.25
362
4.13
105
4
8.2
18
4.75 120.7
3.63
92.2
0.63
16
0.06
1.6
0.75
19
16.5
419
4.5
114.3
4
13.6
30
7.5 190.5
5.5
139.7
4.13
104.9 0.75
19
0.06
1.6
0.75
19
16.5
419
5.13 130.3
4
18.2
40
7.5 190.5
6
152.4
5
19
0.06
1.6
0.75
19
16.5
419
5.13 130.3
4
19.1
42
72
127
0.75
9
228.6
7.5
190.5
6.19
157.2 0.94
23.9
0.06
1.6
0.75
19
23.63
600
19
6
152.4
8
32.7
9.1
231
9
228.6
7.5
190.5
6.19
157.2 0.94
23.9
0.06
1.6
0.75
7.25
184
6
152.4
8
41.4
91
6"
10.5 266.7 10.8
274
11 279.4
9.5
241.3
8.5
215.9
1
25.4
0.06
1.6
0.88 22.4
7.25
184
7.5
190.5
8
70.8
148
8"
11.5 292.1 12.75 324
270
1.13
28.7
0.06
1.6
0.88 22.4
9.75
248
9
228.6
81
117.5
259
12.75 323.9 1.19
30.2
0.06
1.6
1
25.4
9.75
248
11
279.4 122
181.9
401
1
25.4
10
254
N/A
N/A
122
N/A
N/A
1.12 28.4
10
254
N/A
N/A
123
N/A
N/A
13.5 342.9 11.75 298.5 10.63
10"
13
330.2 14.68 373
16 406.4 14.25
12"
14
355.6 16.4
417
19 482.6
1.25
31.8
0.06
1.6
14"
15
442
21 533.4 18.75 476.3 16.25 412.8 1.38
35.1
0.06
1.6
381
17.4
17
362
431.8
15
381
N= Number of holes
(3) 2 top holes in flanges are tapped for 1" -8 UNC Threads
CLASS 300 LBS
Flanged Ends
Wrench Operated
Fig. R303 F
SIZE
L
H
D
mm.
1/2"
5.5
139.7 3.38
86
3.75 95.3
3/4"
6
152.4 3.38
86
1"
6.5
165.1
114
1-1/2" 7.5
2"
8.5
in. mm.
4.5
190.5 5.31 135
215.9 6.25 159
*2-1/2" 11.13 282.7 6.56 167
3"
4"
11.13 282.7 6.56 167
12
4" EG 12
d
Q
G
mm.
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
2.63
66.8
1.38
35.1
0.56
14.2
0.06
1.6
0.63
16
8
203
4.63 117.5 3.25
82.6
1.69
42.9
0.63
16
0.06
1.6
0.75
19
8
203
9
3.5
88.9
2
50.8
0.69
17.5
0.06
1.6
0.75
19
6.13 155.7
124
4.5
114.3
2.88
73.2
0.81
20.6
0.06
1.6
0.88
22.4
6.5 165.1
5
N
Wt's
mm. NO.
(kg)
2.88
73.2
4
4.1
(lbs.)
9
3
76.2
4
5.5
12
229
3.75
95.3
4
7.3
16
14.25 362
4.38
111.3
4
13.2
29
57
127
3.63
92.2
0.88
22.4
0.06
1.6
0.75
19
16.5
419
4.75 120.7
8
25.9
8.25 209.6 5.88
149.4
4.13
104.9 1.13
28.7
0.06
1.6
0.88
22.4
16.5
419
5.56 141.2
8
28.6
63
8.25 209.6 6.63
168.4
5
1.13
28.7
0.06
1.6
0.88
22.4
16.5
419
5.56 141.2
8
28.6
63
127
254
7.88
200.2
6.19
157.2 1.25
31.8
0.06
1.6
0.88
22.4
23.63 600
6.75 171.5
8
53.3
118
10
254
7.88
200.2
6.19
157.2 1.25
31.8
0.06
1.6
0.88
22.4
7.25
184
6.75 171.5
8
65.3
144
270
8.5
215.9 1.44
231
16.5 419.1 12.75 324
457.2 14.68 373
12" 19.75 501.7 16.4 417
30
f
in.
10
9.1
15.88 403.4 10.8 274
14"
b
mm.
304.8
8"
18
g
in.
4.88
mm.
304.8 7.53 191
6"
10"
in.
K
in.
762
17.4 442
12.5 317.5 10.63
36.6
0.06
1.6
0.88
22.4
7.25
184
8.5
215.9
12
110.2
243
1.63
41.4
0.06
1.6
1
25.4
9.75
248
10
254
12
171.5
378
17.5 444.5 15.25 387.4 12.75 323.9 1.88
47.8
0.06
1.6
1.12
28.4
9.75
248
N/A
N/A
16
N/A
N/A
20.5 520.7 17.75 450.9
50.8
0.06
1.6
1.25
31.8
10
254
N/A
N/A
16
N/A
N/A
53.8
0.06
1.6
1.25
31.8
10
254
N/A
N/A
20
N/A
N/A
15
23
381
13
330.2 10.63
15
270
381
2
584.2 20.25 514.4 16.25 412.8 2.12
N= Number of holes
9
Fig. R153/303 SW
CLASS 150/300
Socketweld Ends
SIZE
L
H
D
J
F
in.
mm.
in.
mm.
in.
mm.
in.
mm.
in.
1/2"
3.93
100
3.38
86
0.85
21.7
0.55
14
3/4"
3.93
100
3.38
86
1.07
27.2
0.75
19
1"
5.5
140
4.5
114
1.34
34
0.98
25
1-1/2"
6.3
160
5.31
135
1.92
48.8
1.5
2"
7.87
200
6.25
159
2.4
61
1.97
G
Q
Wt's
mm.
in.
mm.
in.
mm.
(kg) (lbs.)
0.37
9.5
1.69
42.9
8
203
2.1
0.5
12.7
1.8
45.7
8
203
2.1
4.7
0.5
12.7
2.38
60.5
9
229
3.2
7.1
38
0.5
12.7
2.88
73.2 14.25
362
6.4
14.2
50
0.66
16.7
3.38
85.9
419
10.4
23
16.5
4.7
Fig. R153/303 SE
CLASS 150/300
Screwed Ends
SIZE
10
L
H
G
Q
Wt's
in.
mm.
in.
mm.
in.
mm.
in.
mm.
(kg)
(lbs.)
1/2"
3.93
100
3.38
86
1.69
42.9
8
203
2.1
4.7
3/4"
3.93
100
3.38
86
1.8
45.7
8
203
2.1
4.7
1"
5.5
140
4.5
114
2.38
60.5
9
229
3.2
7.1
1-1/2"
6.3
160
5.31
135
2.88
73.2
14.25
362
6.4
14.2
2"
7.87
200
6.25
159
3.38
85.9
16.5
419
10.4
23
SPECIAL PRODUCTS
FLUOROSEAL CAGED PLUG VALVES
Caged Control Valves
The caged control valve is ideal for abrasive applications with high concentrations of solids. The caged control valve is commonly used in both throttling
and on/off applications. Caged valves have been used successfully in many
critical applications in the Mining, Pulp & Paper, and Chemical Processing
industries.
The design of the Caged Control valve provides maximum protection to the
PTFE sealing surfaces in the plug valves. The key to the caged design is that
the PTFE sleeve in the valve is never directly exposed to the process flow. This
allows the sleeve to maintain its sealing integrity in abrasive applications.
The design of the caged control valve allows the plug to rotate freely around
a fixed cage within the body. The cage stays stationary in the body while the
plug rotates around the cage. Thus the sealing area of the plug is in direct
contact with the sleeve to provide bubble tight shutoff. The cage stays in
position protecting the PTFE sleeve from the flow while the plug is in any
intermittent position such as when the valve is moving from the open to the
closed position or when the valve is throttling.
The cage has upper and lower bearings made from either UHMWPE or RTFE
that prevents galling between the plug and cage. A keyway keeps the cage
from rotating in the body. The body has a male key and the cage has a
female keyway that keeps it locked into the body. This allows free movement
of the plug around the cage.
Outer Plug
The caged control valve still allows for in line adjustment for through valve
leakage just as a standard plug valve does since the plug and the cage are
independent of each other.
Caged control valves can be used in many abrasive applications as well as
applications with suspended solids. The cage and plug in the caged control
valve are generally made from CD4MCu material; it’s an abrasion resistant
alloy with the corrosion resistance of 316SS. Caged Control valves are available in any material, from carbon steel and stainless steel to any of the more
exotic alloys.
Cage
Full flow
Plug 00
12
Control flow
Plug throttling
shut-off
Plug 900
V-PORT & CHARACTERIZED PLUGS
FluoroSeal Plug Valves are also available with Characterised Plugs for fine
control applications. Standard V-Ports in 60 deg. and other custom configurations are available in all trim materials.
The design and features of the FluoroSeal plug valve makes it an excellent
choice for fine throttling in slurry and chemical applications. The no cavity
design allows the plug valve to throttle without exposing the stem seal to
line pressure, a definite advantage over most ball valves specifically in high
cycling applications.
The cage control V-Port plug valve is mostly used in highly abrasive applications offering the benefits of a metal seated control valve, with the added
advantage of a bubble tight shutoff at a fraction of the cost. The product is
available in all materials from 1” to 14”.
=
V-Port cage assembly
Typical flow chart for a 1” 60 deg. V-Port.
35
30
25
Cv
20
15
10
5
0
10%
20%
30%
40%
50%
60%
70%
80%
90%
100%
13
FLUOROSEAL® FIRE SEALED SLEEVED PLUG VALVES
FluoroSeal sleeved plug valves with the fire seal top seal have been tested and certified by an independent
laboratory to the requirements of API 607, fourth edition for external leakage.
The FluoroSeal fire seal design utilizes a PTFE sleeve and PTFE diaphragm as the external sealing components
under normal conditions. Should these components be destroyed by fire, external leakage is prevented by:
1. A secondary flexible graphite seal ring
encapsulated and compressed between
the metal diaphragm and the machined
counterbore in the valve body.
2. A flexible graphite delta ring encapsulated and compressed between the
unique shaped metal diaphragm and
the machined plug stem.
FluoroSeal fire seal valves also utilize a vented
plug designed to relieve pressure buildup
resulting from expansion of the service media,
within the plug, due to elevated temperatures
caused by fire. The pressure is relieved to the
upstream side, resulting in a uni-directional
valve, which is indicated by an arrow on the
side of the valve body.
COMBINATION FORMED METAL
DIAPHRAGM AND STATIC
ELIMINATOR
FLEXIBLE GRAPHITE
DELTA RING
PTFE DIAPHRAGM
COVER
FLEXIBLE GRAPHITE RING
BODY
1/8" VENT HOLE ON
UPSTREAM SIDE
OF PLUG
PLUG
Fire Seal Assembly
14
HF ALKY VALVES
FluoroSeal HF Alky valves are designed and manufactured in strict compliance with the requirements of the
major HF Alkylation’s Process Licencesors specifications. Due to the severity of the process, all testing procedures
are strictly adhered to per Licencesor's requirements.
FluoroSeal’s commitment to high quality require each valve
body to be subjected to hydrostatic shell test at 1.5 times the
ANSI rating at 100 Degrees F, as defined in ASME B16.34.
In addition, every valve body casting is tested with Helium gas
at 300 PSIg for 100% assurance
of no through-wall leakage.
We also conduct a full X-Ray
test on the bodies to
ensure that they meet
FluoroSeal’s requirement
of Level 1 castings per
ASTM E446.
Body
Plug
Cover
Cover Bolts
Adjusting Bolts
Thrust Washer
Metal Diaphragm
Delta Ring
Cover Seal Ring
Diaphragm
Sleeve
Paint
ASTM A494 Gr. M35-1
ASTM A494 Gr. M35-1
ASTM A494 Gr. M35-1
ASTM A193 Gr. B7M
ASTM A193 Gr. B7M
ASTM A494 Gr. M35-1
Monel 400
Flexible Graphite
Flexible Graphite
PTFE
GF2P (Molecularly Enhanced PTFE)
Special for leak detection
15
CHLORINE VALVES
Chlorine valves are provided with a pressure relief vent hole in the side of the
plug to relieve pressure to the upstream side. This modification results in a
uni-directional valve which is indicated on the valve whith a flow direction arrow.
Vent holes can also be provided in the bottom of the plug upon request.
FluoroSeal sleeved plug valves are manufactured in accordance with the recommendations of the Chlorine Institute and provide superior performance on this
demanding application. All FluoroSeal chlorine valves are made from thoroughly
cleaned and dried components under controlled conditions and this control is
maintained throughout parts preparation, assembly, testing to special protective
packaging.
Body
Plug*
Cover
Cover Bolts**
Adjusting Bolts
Trust Washer
Metal Diaphragm
Delta Ring
Diaphragm
Sleeve
Carbon Steel ASTMA216 Gr. WCB
Monel ASTM A494 Gr. M35-1
Carbon Steel ASTMA216 Gr. WCB
Steel ASTMA193 B7
Monel
Monel ASTMA494 Gr. M35-1
Monel 400
PTFE
PTFE
PTFE
See Technical Section for material specifications
Plug* - also available in hastelloy C
Cover bolts** - also available in monel
16
FluoroSeal Severe Service Sleeved Plug Valves
FluoroSeal has developed this FE model sleeved plug valve for
tight emission control in more demanding services. This valve is
intended for applications in processes involving thermal cycles or
a high number of mechanical operations. Proven features from
the standard FluoroSeal sleeved plug valve form the basis of the
design, combined with innovative use of other proven seal technologies all incorporated into a compact but robust package.
Extensive testing across the envelope of intended conditions
have proven the capability of the design to perform under
varying applications.
*Please ask your local Rep. for a full fugitive EMISSION
TEST REPORT.
DESIGN FEATURES
In-line seal adjustable
independent of
shaft seal.
Standard lockout
capability and solid
position stop.
Innovative shaft seal*
provides self-adjusting,
redundant and independent packing available in all PTFE or PTFE
and flexible graphite
combination. Configured
for optional monitoring
or injection port.
Primary shaft seal
extrusion is controlled
with reinforced PTFE
end rings, secondary
shaft seal utilizes tight
gap metallic shaft for
full metal to metal
containment.
Bonnet is double sealed
with fully contained
independent PTFE and
flexible graphite seal
backing up the primary
seal at the sleeve.
PTFE sleeve provides
inline and primary external seals. Performance is
enhanced with full
encapsulation at port
opening and precise
body ribs to focus sealing forces on plug.
Precision (Investment)
cast body provides tight
dimensional control to
assure concentricity
between plug and body.
This minimizes induced
side loads to the primary
seals and shaft seals during operation.
*Patent Pending
17
DIMENSIONS – with handle
Class 150
SIZE
L
HT
H
D
B
G
N
O
P
QC
E
1
5.00
7.38
6.94
4.25
0.44
2.00
4
0.63
3.12
10.24
9.94
2
7.00
8.88
8.25
6.00
0.63
3.63
4
0.75
4.75
16.73 12.75
3
8.00
9.38
8.75
7.50
0.75
5.00
4
0.75
6.00
16.73 14.38
4
9.00
11.44
10.44 9.00
0.94
6.19
8
0.75
7.50
23.62 17.62
6
10.50
-
15.70 11.00
1.00
8.50
8
0.88
9.50
-
23.75
8
11.50
-
19.38 13.50
1.13
10.63
8
0.88
11.75
-
31.00
SIZE
L
HT
H
D
B
G
N
O
P
QC
E
1
6.50-
7.38
6.94
4.88
0.69
2.00
4
0.75
3.50
10.24
9.94
Class 300
2
8.50
8.88
8.25
6.50
0.88
3.63
8
0.75
5.00
16.73 12.75
3
11.13
9.38
8.75
8.25
1.13
5.00
8
0.88
6.63
16.73 14.38
4
12.00
11.44
10.44 10.00
1.25
6.19
8
0.88
7.88
23.62 17.62
6
15.88
-
15.70 12.50
1.44
8.50
12
0.88
10.62
-
23.75
8
16.50
-
19.38 15.00
1.63
10.63
12
1.00
13.00
-
31.00
10" and up dimensions supplied upon request.
NOTE:
This product is engineered for each application
and is available in many alloys as well as
custom configurations.
Let us know your specific needs
ITEM NO. QTY
1
1
2
1
3
1
4
1
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
18
1
1
1
1
1
1
1
2
2
1
4
1
1
1
1
1
1
1
1
1
DESCRIPTION
Bonnet
Plug Adjuster
Packing Gland
Packing Set
& Virgin PTFE
Follower
Belleville Washer
Seal Washer
Top Packing
Seal Retainer
Shaft adapter
Stop
Packing Bolt
Plug Bolt
Plug
Bonnet Bolt
BodySeal Retainer
BodySeal
BodySeal
Body
Thrustwasher
Sleeve
Handle
Handle Bolt
Pipe Plug
MATERIALS
Customer Specified
ASTM A351 CD-4MCU
ASTM A351 CD-4MCU
Carbon Fld. PTFE
Customer Specified
Inconel
Nitronic 60
Flexible Graphite or PTFE
Nitronic 60
304 Stainless Steel
304 Stainless Steel
304 Stainless Steel
304 Stainless Steel
Customer Specified
Customer Specified
Customer Specified
Flexible Graphite
Virgin PTFE
Customer Specified
Carbon RPTFE
Virgin PTFE
Carbon Steel
Carbon Steel
316 Stainless Steel
DOUBLE BLOCK AND BLEED AND SAMPLING VALVES
Because of the double port seals in both directions
and the sealed isolation of the chamber below the
plug and the areas around the plug, 900 to the port
openings, a drainage connection into the plug cavity may be drilled and tapped through the body from
either side or the bottom.
BLOCK VALVE
A 1/4” drain connection is standard, but other sizes
can also be provided. Specify connection size; length
as indicated on the drawing and whether the bleed
valve is required. A FluoroSeal Fig. R152/302SE is ideally suited as the bleed valve.
SPECIFY
BLEED VALVE
Valve
Bleeding
Size
Valve size
(Inches) (Inches)
2
1/2
2-1/2
1/2
3
1/2
4
1/2
5
3/4
6
3/4
8
3/4
10
1
12
1
14
1
16
1
18
1
24
1
19
ENGINEERED SOLUTIONS DIVISION
Our Engineered Solutions Division (ESD) is staffed with highly skilled engineers,technicians and
draftsmen specialized in modifying existing designs to meet your special needs.
You are not sure of the compatibility of
your process with your valve selection? We
will assist you in making the most appropriate selection of alloys and Polymers to
suite your application.
You are not sure if your valve selection
will meet your flow parameters ? We will
provide you with CV factor and other flow
calculations that you need , therefore
making your selection process as easy
as possible.
You need non-standard valve configuration or geometry to meet a special application ? We will work together with you
to develop it.
20
JACKETED VALVES
JACKETED VALVES
We are proud to offer our latest product, a Fully
jacketed Plug Valve with standard flanges.
There’s no more need to oversize the piping
flanges, translating in tremendous savings to the
user.
Among other features, the ease of installation
allows any FluoroSeal plug valve to be retro-fitted in-line in process.
FluoroSeal plug valves are also available with
Partial Steam Jackets, choose accordingly to the
application requirements.
New
Full Jacket using the valve body
standard flanges
(Jacket Pressure rating available in
150 & 300 Lbs)
Standard Full Jacket
with oversized Flanges
Three Way Full Jacket
Partial Jacket Welded
22
There’s No limits to the possibilities all our
valves in all trim materials are available in
either a two way or multi-port versions, with
partial or full jackets
Dimensional data for full jacketed valves with oversized flanges
Class 150 Wrench Operated
Size
Units
L
H
D
BC
g
b
f
d
N
Q
2” x 1” x 2”
inch
7.00
7.00
6.00
4.75
3.63
.63
.06
.75
4
12.00
mm
177.8
177.8
152.4
120.7
92.0
16.0
1.6
19.0
4
304.8
21/2” x 11/2” x 21/2”
inch
8.00
7.625
7.50
5.50
4.13
.75
.06
.75
4
16.00
mm
203.2
193.7
190.5
139.7
104.6
19.0
1.6
19.0
4
406.4
3” x 2” x 3”
inch
8.00
8.00
7.50
6.00
5.00
.75
.06
.75
4
24.00
mm
203.2
203.2
190.5
152.4
127.0
19.0
1.6
19.0
4
609.6
4” x 3” x 4”
inch
9.00
9.00
9.00
7.50
6.19
.94
.06
.75
8
24.00
mm
228.6
228.6
228.6
190.5
157.2
23.9
1.6
19.0
8
609.6
6” x 4” x 6”
inch
10.50
10.00
11.00
9.50
8.50
1.00
.06
.88
8
36.00
mm
266.7
254.0
279.4
241.3
215.9
25.4
1.6
22.4
8
914.4
Size
Units
L
H
D
BC
g
b
f
d
N
Q
6” x 4” x 6”
inch
10.5
11.50
11.00
9.50
8.50
1.00
.06
.88
8
9.00
mm
266.7
292
279.4
241.3
215.9
25.4
1.6
22.4
8
228.6
8” x 6” x 8” EG
inch
11.5
13.00
13.50
11.75
10.63
1.13
.06
.88
8
12.00
mm
292.1
330
342.9
298.5
269.8
28.7
1.6
22.4
8
304.8
Size
Units
L
H
D
BC
g
b
f
d
N
Q
2” x 1” x 2”
inch
8.50
5.00
6.50
5.00
3.63
.88
.06
.75
8
12.00
mm
215.9
127
165.1
127.0
92.2
22.4
1.6
19.0
8
304.8
21/2” x 11/2” x 21/2”
inch
11.13
5.31
8.25
5.88
4.13
1.13
.06
.88
8
16.00
mm
282.7
135
209.6
149.4
104.9
28.7
1.6
22.4
8
406.4
3” x 2” x 3”
inch
11.13
5.31
3.25
6.63
5.00
1.13
.06
.88
8
24.00
mm
282.7
135
209.6
168.4
127.0
28.7
1.6
22.4
8
609.6
4” x 3” x 4”
inch
12.00
6.10
10.00
7.88
6.19
1.25
.06
.88
8
24.00
mm
304.8
155
254.0
200.2
157.2
31.8
1.6
22.4
8
609.6
6” x 4” x 6” EG
inch
15.88
11.50
12.50
10.63
8.50
1.44
.06
.88
12
36.00
mm
403.4
292
317.5
270.0
215.9
36.6
1.6
22.4
12
914.4
Size
Units
L
H
D
BC
g
b
f
d
N
Q
6” x 4” x 6” EG
inch
10.5
11.50
11.00
9.50
8.50
1.00
.06
.88
8
9.00
mm
266.7
292
279.4
241.3
215.9
25.4
1.6
22.4
8
228.6
8” x 6” x 8” EG
inch
11.5
13.00
13.50
11.75
10.63
1.13
.06
.88
8
12.00
mm
292.1
330
342.9
298.5
269.8
28.7
1.6
22.4
8
304.8
Class 150 Enclosed Gear operated
Class 300 Wrench Operated
Class 300 Enclosed Gear operated
Other dimensions supplied upon request
Full jacket 3 way valves are also available. Consult your nearest FluoroSeal Distributor for these and
other special requirements.
23
PARTIAL JACKETED VALVES
Heat dissipation due to the partial insulating effect of the PTFE sleeve, combined with the basic plug valve
design, provides a more uniform heat flange to flange with a partial jacket than with a full jacket. Therefore, a
partial jacket should be selected for most applications.
Refer to standard valves for dimensional data
2 Way Class 150 & 300
4" to 12"
Enclosed Gear Operated
1" to 4"
Wrench Operated
3 Way Class 150 & 300
4" to 8"
Enclosed Gear Operated
1" to 4"
Wrench Operated
JACKET INLET OUTLET AND DRAIN CONNECTIONS
24
Valve Size
1
11/2
2
3
4
6
8
10
12
NPT
3/8
1/2
1/2
1/2
1/2
1
1
1
1
TECHNICAL DATA
AND ACCESSORIES
CV VALUES / TORQUES
Cv Values - For 2 Way Valves
Valve Size
1/2"
3/4"
1"
1 1/2"
2"
3"
4"
6"
8"
10"
12"
Cv Values - For Caged Control Valve
10
20
Degrees Open
30
40
50
0.0
0.0
0.2
0.4
0.9
1.6
0.0
0.0
0.2
0.4
0.9
1.6
2.7
5.4
9
0.0
0.0
1.1
1.7
4.3
7.7
13.0
26.0
43
0.0
0.2
2.7
6.7
12.5
25.0
37.0
58.0
89
0.0
1.9
6.9
12.0
21.0
34.0
55.0
101.0
172
0.0
5.0
8.8
21.0
44.0
60.0
103.0
182.0
294
0.0
9.8
30.0
56.0
99.0
145.0
208.0
345.0
548
0.0
13.0
45.0
90.0
140.0
245.0
380.0
634.0
1075
0.0
19.0
51.0
103.0
183.0
317.0
541.0
939.0
1591
0.0
23.0
69.0
140.0
248.0
430.0
734.0
1274.0
2159
0.0
27.0
102.0
208.0
368.0
637.0
1088.0 1888.0
3200
Cv Values for 3 Way Valves
FA
FA4
FA4
1, 2, 3, 5 Pos. A&C Pos. B
1/2"
9
6
6
3/4"
9
6
6
1"
20
11
17
1 1/2"
36
19
33
2"
68
37
43
3"
88
47
78
4"
154
86
139
6"
315
189
227
8"
425
324
408
10"
645
452
753
12"
—
—
—
14"
—
—
—
60
70
80
90
2.7
5.4
9
Valve Size
1"
1 1/2"
2"
3"
4"
6"
8"
10"
12"
10
0
0
0
0
0
0
—
—
—
Degrees Open
20 30 40 50
0 1.7 3.4 6.3
0.8 3.6 7.2 12.5
1.7 5.5 11.1 25
4.5 9.4 21 35
9.8 30 55 82
12.9 43 86 138
— — — —
— — — —
— — — —
60
10
20.6
30
54
138
232
—
—
—
70
18
34
52
103
193
378
—
—
—
80
32
55
90
162
336
593
—
—
—
CV Values for Standard V-Port
Size
Valve Size Pipe Size
1"
2"
1 1/2"
1"
1 1/2"
3"
2"
1 1/2"
2"
4"
3"
2"
3"
6"
4"
3"
4"
8"
6"
4"
6"
10"
8"
6"
10% 20% 30% 40%
0.31 1.15 2.47 4.27
0.35 1.29 2.78
4.8
0.38 1.42 3.06 5.27
0.38 1.39 3.01 5.18
0.39 1.45 3.13 5.39
0.4
1.48
3.2
5.52
0.64 2.37 5.11
8.81
0.67 2.48 5.34
9.2
0.69 2.55
5.5
9.48
1.43 5.31 11.45 19.75
1.51
5.6 12.06 20.8
1.54 5.74 12.37 21.33
2.226 8.39 18.1 31.21
2.35 8.73 18.81 32.44
2.42 9.01 19.42 33.5
4.9 18.21 39.26 67.7
4.95 18.4 39.67 68.4
5.1 18.97 40.89 70.52
Percentage Open
50%
60% 70%
6.51
9.2
12.31
7.32 10.34 13.84
8.04 11.36 15.22
7.91 11.17 14.96
8.23 11.63 15.57
8.42 11.89 15.93
13.45
19
25.44
14.04 19.84 26.56
14.47 20.44 27.38
30.13 42.56 57.59
31.75 44.84 60.09
32.55 45.98 61.57
47.62 67.26 90.07
49.5 69.92 93.63
51.12 72.2 96.69
103.31 145.93 195.41
104.39 147.45 197.44
107.62 152.01 203.55
80%
15.68
17.83
19.59
19.27
20.05
20.51
32.77
34.21
35.26
73.4
77.33
79.3
115.99
120.58
124.51
251.65
254.27
262.13
90%
19.82
22.28
24.49
24.08
25.07
25.64
40.96
42.76
44.07
91.74
95.66
99.12
144.99
150.72
155.64
314.55
317.82
327.65
Operating Torque (in.lbs) Standard Port
Size
1/2"
3/4"
1"
1 1/2"
2"
3"
4"
6"
8"
10"
12"
14"
Break torque
140
140
400
800
1100
1200
2400
5000
7800
14400
21000
21000
Torque adjustment factors:
1. For UHMWPE sleeves: Multiply value by 2
2. For slurry or abrasive service: Multiply value by 1.5
Note: Torque values are the same for 2 way and 3 way valves
26
90
40.9
80.3
138
235
439
860
—
—
—
Seating Torque
80
80
250
500
650
700
1450
3000
4700
8600
12600
12600
Running torque
70
70
200
400
550
600
1200
2500
3900
7200
10500
10500
100%
24.2
27.2
29.9
29.4
30.6
31.3
50
52.2
53.8
112.01
117.01
121.01
177.01
184.01
190.01
384.03
388.03
400.03
TECHNICAL DATA
Quality Assurance
Pressure-Temperature Chart
Class 150
Fluoroseal valves possess all of
the best design features
presently available in a nonlubricated plug valve. They
are inspected throughout the
full manufacturing process
from foundry to final assembly and packaging to assure
high quality and consistency
in each and every unit.
CF3-CF8M
LCB
260
240
CF3-CF8
CN7M
Pressure 9psig)
Hi-temp sleeve limit
WCR
280
GF2P sleeve limit
PTFE sleeve limit
300
220
N12MV-CW12MW
200
180
160
140
120
600
500
475
400
300
200
100
-20
100
Temperature (deg. F)
All valves are pressure tested
prior to shipment and fully
compliant to ANSI B16.34 shell
tests and MSS SP-61 seat test
requirements. All nickel alloys
are helium tested as standard.
Class 300
inspected
800
WCR
700
LCB
throughout
N12MV-CW12MW
400
300
100
GF2P sleeve limit
PTFE sleeve limit
200
600
500
475
400
300
200
0
-20
process
500
100
manufacturing
CF3-CF8
CF3-CF8M
Pressure 9psig)
the full
CN7M
600
27
TECHNICAL DATA
Class 600
CF3-CF8M
1400
LCB
WCR
GF2P sleeve limit
1500
PTFE sleeve limit
1600
Pressure 9psig)
1300
1200
CF3-CF8
1100
1000
CN7M
900
N12MV-CW12MW
800
600
500
475
400
300
200
100
-20
700
Testing:
• All our valves are tested with dry air to 1.5 times the full rated pressure of class 150 as per ANSI
B16.34 paragraph 7.1.
• All our valves in classes 150, 300 and 600 are tested in full compliance with ANSI B16.34
paragraph 7.2.
• Our Fire-Safe valves are tested to API607 fourth edition.
28
ACCESSORIES
T-Wrench and Extension Option
Valve Size
1/2
3/4
1
11/2
2
3
4
Q
12
12
12
16
24
24
36
H
6
6
7
8
8
9
10
If longer “H” dimension, please specify.
Handwheel Extension - Gear Operator
Heavy duty gear
supplied as standard
Support may be required depending on the
length of the extension.
(To be supplied by customer.)
Stem Extension - Gear Operator
Stem extensions are used for remote operation of the valve. Actuators can be
attached to the top of the extension. Specify the length of the extension required
and the figure number of the valve it is to be attached to.
Crank Handle
Units
4” EG
inch
10.75
8.00
9
mm
273
203
229
inch
11.50
10.00
12
mm
292
254
305
inch
13
10.00
15
mm
330
254
381
inch
15.50
12.00
18
mm
394
305
457
inch
17.25
12.00
15
mm
438
305
381
6” EG
8” EG
10” EG
12” EG
Chain Wrench
Valve Size Units
Q
1/2
3/4
1
11/2
2
3
4
inch
13
13
16
24
36
36
48
mm
330
330
406
610
914
914
1219
H
Q
Handwheel
Dia.
Size
Specify the chain length required and
whether the valve will be install in a horizontal
or vertical line.
To calculate chain length:
900 rotation: 1. Double required drop
2. Multiply “Q” by .5
3. 1+2= required chain length
1800 rotation: Double calculation for 900
Chain Wheel
Specify the chain length required and
whether the valve will be install in a
horizontal or vertical line.
To calculate chain length:
1. Double required drop “B”.
2. Multiply chain wheel diameter
“A” by 2.6.
3. 1+2= required chain length.
29
WRENCH OPERATOR LOCKING DEVICE
Pad lock is not supplied.
GEAR OPERATOR LOCKING DEVICE
Pad lock is not supplied.
30
PRODUCT AVAILABILITY
END CONNECTION
SIZE RANGE
Threaded or socket weld
1/2” to 2”
Flanged Raised & Flat Face
1/2” to 24”
Buttweld
1/2” to 24”
Ring type joint
1/2” to 24”
1/2” to 2”
1/2” to 24”
Buttweld
1/2” to 24”
Ring type joint
1/2” to 24”
1/2” to 2”
1/2” to 14”
Buttweld
1/2” to 14”
Ring type joint
1/2” to 14”
1/2” to 2”
1/2” to 8”
Buttweld
1/2” to 8”
Ring type joint
1/2” to 8”
1/2” to 2”
1/2” to 8”
Buttweld
1/2” to 8”
Ring type joint
1/2” to 8”
1/2” to 2”
1/2” to 8”
Buttweld
1/2” to 8”
Ring type joint
1/2” to 8”
Standard port
PRESSURE CLASS
Class 150
Class 300
Class 600
Full port
PRESSURE CLASS
Class 150
Class 300
Class 600
Material selection
Body, Plug & Sleeve material selection guide is available in the How to Order section.
Manual operators
Wrench
1/2” to 4”
T-Bar
1/2” to 4”
Enclosed Gear
2” to 24”
Heavy duty gear is standard
31
HOW TO ORDER
FLUOROSEAL SLEEVED PLUG VALVES
Size
Size
Range available from 1/2" to 24"
Refer to catalog for Class availability
Port
R: Reduced Port
F: Full Port
Class
15: Class 150
30: Class 300
60: Class 600
Flow
2: 2 Way
3: 3 Way
End Connection
F: Flanged Raised Face
FF: Flanged Flat Face
SE: Screwed
SW: Socket Weld
X: Screwed x Socket Weld
BW: Buttweld
S: Special
Operator
W: Wrench
WL: Wrench + Locking device
EG: Enclosed Gear
EGL: Enclosed Gear + Locking device
B: Bare Stem
Flow Pattern (leave blank for 2 way)
FA1, FA2, FA3, FA4, FA5
Refer to catalog for patterns
Body Material
Refer to Body & Plugs Material Table
Plug Material
Refer to Body & Plugs Material Table
Sleeve Material
P: PTFE
R: RTFE
G: GF2P
A: PFA
U: UHMWPE
K: PEEK
Z: HIGH TEMPERATURE TEFLON
Special
(Combination of Specials can be used)
FS: Fire Safe
FE: Severe Service Valves
HF: HydroFluoric Acid Valves
CL: Prepared for Chlorine Service
OX: Prepared for Oxygen Service
DBB: Double Block & Bleed
PJ: Partial Jacket
FJ: Full Jacket
CCV: Cage Control Valve
V6: V-Port 60 Deg.
S: Special (description required)
VN: Vented Plug (specify location & Diameter)
U: Upstream
D: Downstream
B: Bottom
Exemple for Vented Plug:
VN(U,B,1/4")
Note: HF,FS,CL are vented by defaut, refer to catalog for
details.
32
Port
Class
Flow
End
Connection Operator
/
/
-
Flow
Pattern
-
Body
Material
/
Plug
Material
-
Sleeve
Material
Body & Plugs Material Table
CODE
DESCRIPTION
ASTM DESIGNATION
DI
Ductile Iron
A395
WCB
Carbon steel
ASTM A216 WCB
LCB
Carbon steel Low Temp.
ASTM A352
304
304 stainless steel
ASTM A351 CF8
304L
304L stainless steel
ASTM A351 CF3
316
316 stainless steel
ASTM A351 CF8M
316L
ASTM A351 CF3M
317
317 stainless steel
ASTM A351 CG8M
317L
ASTM A351 CG3M
A20
Alloy 20
ASTM A351 CN7M
B61
Bronze
ASTM B61
CD4
CD4MCu
ASTM A351 CD4MCu
HB
Hastelloy B
ASTM A494 N7M
HB2
Hastelloy B 2
ASTM A494 N12MV
HC
Hastelloy C
ASTM A494 CW6M
I600
Inconel
ASTM A494 CY40
NI
Nickel
ASTM A494 CZ-100
MO
Monel
ASTM A494 M-35-1
NAB
Ni-Al Bronze
ASTM B367 Gr.958
TC3
Titanium
ASTM B367 Gr.C3
ZC2
Zirconium
ASTM B752 Gr. 702C
ZC5
Zirconium
ASTM B752 Gr. 705C
OTHER & SPECIAL ALLOYS AVAILABLE ON REQUEST
-
Special
FLUOROSEAL INC.
WARRANTY TERMS & CONDITIONS
PLUG VALVES
CONTROLLING PROVISIONS:
9
These terms and conditions shall control
with respect to any purchase order or
sale of Fluoroseal's products. No waiver,
alteration or modification of these terms
and conditions whether on Buyer's purchase order or otherwise, shall be valid
unless the waiver, alteration or modification is specifically accepted in writing
and signed by an authorized representative of Fluoroseal Inc.
4
2
3
10
5
1
6
8
7
Design Features Summary
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
Bi-directional inline bubble tight seal independent of line pressure.
Multiple external bubble tight seals independent of line pressure.
Direct mechanical three point adjustment independent of line pressure.
Independent travel stops.
Full encapsulation and retention of all leading edges of PTFE sleeve and
top seal components.
Full lip at port openings protects PTFE sleeve.
Contoured waterway assures minimum flow turbulence characteristic.
No body cavities to entrap flow media.
Positive flow direction indication.
Drilled and tapped flange mounting pads independent of cover and top
seal assembly.
Other Features
-
Bi-directional flow.
Quarter turn operation
Nonlubricated
Self-cleaning on each operation.
Two way and multiport configurations
Special service and jacketed designs available.
All casting components traceable to mill test certificates.
Investment cast on all materials for sizes 1/2" - 10" (Class 150)
Castings meet level 1 casting specifications
Heavy duty gears are standard on all our valves
DELIVERY: Fluoroseal Inc. will make
every effort to complete delivery of
products as indicated on its acceptance
of an order, but Fluoroseal assumes no
responsibility or liability, and will
accept no backcharge, for loss or damage due to delay or inability to deliver
caused by acts of God, war, labor difficulties, accident, delays of carriers, by
contractors or suppliers, inability to
obtain materials, shortages of fuel and
energy, or any other causes of any kind
whatever beyond the control of
Fluoroseal Inc. Fluoroseal may terminate any contract of sale of its products
without liability of any nature, by written notice to Buyer, in the event that
the delay in delivery or performance
resulting from any of the aforesaid
causes shall continue for a period of
sixty (60) days. Under no circumstances
shall Fluoroseal Inc. be liable for any
special or consequential damages or
for loss, damage, or expense (whether
or not based on negligence) directly or
indirectly arising from delays or failure
to give notice of delay.
WARRANTY: Fluoroseal Inc. warrants
for one year from the date of shipment
of its manufactured products to the
extent that Fluoroseal will replace
those having defects in material or
workmanship when used for the purpose and in the manner which
Fluoroseal recommends. If Fluoroseal’s
examination shall disclose to its satisfaction that the products are defective,
and an adjustment is required, the
amount of such adjustment shall not
exceed the net sale price of the defective product(s) only and no allowance
will be made for labor or expen-se for
repairing or replacing defective products or workmanship or damage resulting from the same. Fluoroseal Inc. warrants the products which it sells of
other manufacturers to the extent of
the warranties of their respective makers. Where engineering design or fabrication work is supplied.
Buyer's
acceptance of Fluoroseal's design or of
delivery of work shall relieve Fluoroseal
Inc. of all further obligation, other
than expressed in Fluoroseal's product
warranty.
THIS IS FLUOROSEAL'S INC SOLE WARRANTY. FLUOROSEAL INC. MAKES NO
OTHER WARRANTY OF ANY KIND,
EXPRESSED OR IMPLIED, AND ALL
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE WHICH EXCEED
THE AFORESTATED OBLIGATION ARE
HEREBY DISCLAIMED BY FLUOROSEAL
INC AND EXCLUDED FROM THIS WARRANTY.
Fluoroseal Inc. neither assumes, nor
authorizes any person to assume for it,
any other obligation in connection with
the sale of its engineering designs or
products. This warranty shall not apply
to any products or parts of products
which (a) have been repaired or altered
outside of Fluoroseal's factory, in any
manner; (b) have been subjected to
misuse, negligence or accidents; (c)
have been used in a manner contrary to
Fluoroseal's instructions or recommendations. Fluoroseal Inc. shall not be
responsible for design errors due to
inaccurate or incomplete information
supplied by Buyer or its representatives.
FLUOROSEAL'S LIABILITY: Fluoroseal
Inc. will not be liable for any loss, damage, cost of repairs, incidental or consequential damages of any kind,
whether based upon warranty (except
for the obligation accepted by
Fluoroseal Inc. under "Warranty"
above), contract or negligence, arising
in connection with the design, manufacture, sale, use or repair of the products or of the engineering designs
supplied to Buyer.
RETURNS: Fluoroseal Inc. cannot accept
return of any product(s) unless its written permission has been first obtained,
in which case same will be credited
subject to the following: (a) All material returned must, on its arrival at
Fluoroseal's plant, be found to be in
first-class condition; if not, cost of putting in saleable condition will be
deducted from credit memoranda; (b)
A handling charge deduction of twenty percent (20%) will be made from all
credit memoranda issued for material
returned; (c) Transportation charges, if
not prepaid, will be deducted from
credit memoranda.
SHIPMENTS: All products sent out will
be carefully examined, counted and
packed. The cost of any special packing or special handling caused buy
Buyer's requirements or requests shall
be added to the amount of the order.
No claim for shortages will be allowed
unless made in writing within ten (10)
days of receipt of a shipment. Claims
for products damaged or lost in transit
should be made to the carrier, as
Fluoroseal's responsibility ceases, and
title passes, on delivery to the carrier.
SPECIAL PRODUCTS: Orders covering
special or non-standard products are
not subject to cancellation except on
such terms as Fluoroseal Inc. may specify on application.
PRICES AND DESIGNS: Prices and
designs are subject to change without
notice. All prices are F.O.B. Point of
Shipment, unless otherwise stated.
TAXES: The amount of any sales, excise
or other taxes, if any, applicable to the
products, shall be added to the purchase price and shall be paid by Buyer
unless Buyer provides Fluoroseal Inc.
with an exemption certificate acceptable to the taxing authorities.
NUCLEAR PLANTS: Where the products, engineering design or fabrication
is for nuclear plant applications. Buyer
agrees (a) to take all necessary steps to
add Fluoroseal Inc. as an insured under
the American Nuclear Insurers' (ANI)
pool and under the Mutual Atomic
Energy Reinsurance Pool (MAERP) for
property damage and liability insurance and if necessary steps could have
been taken, but are not taken, Buyer
shall hold Fluoroseal Inc. harmless
against all such losses which could
have been thus covered (b) Buyer
agrees to hold Fluoroseal Inc. harmless
with respect to any personal injury or
death, property damage or any other
loss in a nuclear incident which is
caused directly or indirectly by defective design, material, or workmanship,
furnished by Fluoroseal Inc. and which
is covered by insurance maintained by
Buyer (or which could be so covered
but with respect to which Buyer has
elected to self-insure), and further
agrees to waive subrogation by its carriers of such insurance against
Fluoroseal Inc., and (c) as to nuclear
hazards for which Buyer cannot obtain
insurance coverage, the liability of
Fluoroseal Inc. for any personal injury
or death, property damage or any
other loss directly caused by defective
design, material, or workmanship furnished by Fluoroseal Inc. shall not
exceed the value of the material furnished by Fluoroseal Inc. at the time of
the loss occurrence.
MINIMUM INVOICE: $100 plus shipping.
TERMS: Cash, net 30 days unless
otherwise specified.
SLEEVED PLUG VALVES
6418, Trans-Canada Highway W., Montreal, (Qc), Canada H4T 1X4
Tel.: (514) 739-0220 • Fax: (514) 739-5452
1-888-269-0220
e-mail: info@fluorosealvalves.com
AV-102004 PRINTED IN CANADA

Sleeved Plug Valves

Transcription

Similar documents

Gas Essentials Inc.

Tufline® Sleeved Plug Valves

A guide to dismantling the Theoben H.E. Gas Ram

XOMOX® Tufline® Lined Plug Valves

The list of publications

Lined Plug Valves Catalogue (Whole - 2 Mb)

Cardiovascular System II

brands you trust. Tufline® Severe Service Valves

Pool Valves / TruSeal Diverter Valves and Swing

Corporate Leaflet

Sunbelt Supply Co

CheckValves

FITS Al1L KM electronic OverDrive

Valve Guide