The Kill Light® Motion Feeder Light Instructions

The Kill Light® Motion Feeder Light Instructions
Thank you for purchasing The Kill Light® Motion Feeder Light from Elusive Wildlife
Technologies, LP. Many years of testing and research have gone into developing The Kill
Light® Motion Feeder Light. It is our sincere desire that you will have as much fun using
it as we do. If you have not already done so, please check with your local game laws to
make sure it is legal to use a light source while hunting or observing animals at night.
Front
Step 1
Remove the Locking Screw on the side of
The Kill Light® with a Phillips screwdriver.
Elusive Wildlife Technologies, LP and its affiliates do not condone the use of these lights
to illegally take game animals. Please take a moment to thoroughly read the instructions
and helpful tips to get the most out of your Kill Light®, and to ensure you don’t void your
warranty. Good luck and happy hunting.
Back
Step 2
Rotate the top of light until the white
arrow moves from the lock to unlock
position.
Inside
Step 3
Gently separate the bottom and top half
of light by pulling the top half away from
the bottom half of light.
Step 4
Install 4 C size Alkaline batteries. Set
desired motion time or timer setting.
Reassemble light, and reinstall Locking
Screw. See reverse page for timer settings.
Operating the Kill Light®
The Kill Light® can be turned OFF with the switch on the front of the
light. When the switch is in AUTO (Motion) position the light will only
come on at night when motion is detected, and it will stay on for the
selected amount of time as described in the Motion - Timer Instructions
below. When the switch is in the ON (Timer) position it will turn on at
dusk and stay on for the selected amount of time. The on/off switch
is almost flush with the front of the light to prevent animals from
accidentally turning the light on or off.
Important The Kill Light® Motion Feeder Light should be reset before
making changes to the Motion-Timer dip switch settings on the inside
of the light. To do this, turn the Off/Auto/On switch on the front of the
light to the Off position before making changes to the Motion-Timer
dip switches. Once the Motion-Timer dip switches are changed to the
desired setting then move the Off/Auto/On switch on the front of the
light to the Auto (for motion activation) or On (for dusk-to-dawn timer
activation) position.
Mounting the Kill Light®
The Kill Light® is designed to be mounted in three ways.
1.
Magnetically attach The Kill Light® to the bottom of your feeder
control unit or barrel.
2.
Hang on your feeder varmint cage by installing one of the quick
clips directly to the center swing out loop on the back of the light
and attach the light to the varmint cage. You can also hang the
light from a tree limb where you know hogs roam or root around,
and bait that location if allowed in your state.
Helpful Tip If it is windy or if it could become windy do not hang
the light by the center swing out loop. Use the 3 outside swing out
loops and attach a quick clip to all 3, then hang to your varmint
cage to prevent the light from blowing around in the wind. This
could cause the animals to be spooked by their own shadows
dancing around.
3.
Permanently attach under your feeder by using the three self
drilling screws and metal tab protectors. Simply place a metal
protector tab over the plastic mounting tab on the light and
install the self drilling screws. Important The metal protector
tabs have been included with your light, and must be used when
permanently mounting to prevent animals from chewing on the
tabs and causing the light to possibly fall off the feeder.
with the LED’s facing the ground to prevent water damage from rain
or condensation. Take care to insure the light is mounted properly
and always install the light safely inside a varmint cage when leaving
the light on a feeder for extended periods of time. Elusive Wildlife
Technologies, LP will not warranty any light damaged by user neglect or
failure to adhere to these instructions and guidelines. No lights will be
warranted due to water penetration or from animal damage.
Date of Purchase________________________________________ q Ms. q Mr.
Name_________________________________________________________
Address________________________________________________________
Powering the Kill Light®
The Kill Light® operates on 4 C batteries, and will last approximately
25–30 days if set to come on for one minute after motion is detected or
7–10 days if set to stay on all night. The Kill Light® can also be powered
by the optional power cord that has been included with your Kill
Light®. The optional power cord can be used to power the light from an
auxiliary 6 or 12 volt DC power source. A 6 or 12 volt feeder battery will
operate the light, but not as long as with the 4 C batteries. It is highly
recommended that if you decide to power your light longer and make it
maintenance free with this cord that you use a large 12 volt car battery
or deep cycle marine type battery, a charge controller, and a 10 watt
solar panel on the battery to ensure the battery will stay charged and
have enough current to power the light every night.
Warranty
Elusive Wildlife Technologies, LP warranties this product for one
year from the original purchase date. Please complete the warranty
registration and mail it in to register your light. You may also e-mail the
warranty registration information to info@elusivewildlife.com.
Your Kill Light® is NOT waterproof. It is water resistant ONLY when
used as intended. The Kill Light® must be hung or mounted level
City, State, Zip____________________________________________________
Phone_________________________________________________________
E-mail_________________________________________________________
q Received as a gift
q Purchased for yourself
Name of store where purchased_________________________________________
Please rate your satisfaction with this product from 1–10 with 10 being the most satisfied. If you
have not used this product please enter N/A. _________
Elusive Wildlife Technologies, LP respects your privacy, and we will not sell or provide personal information
to any other party. However, we would like to occasionally send you information about your Elusive Wildlife
product or special offer. If you do not wish to receive this information please check here q.
Please mail or e-mail warranty info to:
Elusive Wildlife Technologies, LP
1107 West Dallas Street • Suite A • Conroe, TX 77301
800-780-6861 • info@elusivewildlife.com
Motion - Timer Instructions
Off / Motion / Timer Switch
Off / Motion / Timer Switch
Off / Motion / Timer Switch
Dip Switch
Position
Off/Motion/Timer
Switch Position
Duration After
Motion Trigger
Dip Switch
Position
Off/Motion/Timer
Switch Position
1 Minute
Switch in this position will operate the Kill
Light® motion sensor timer. The light will
turn on when motion is detected and stay on
for selected amount of time.
Dip Switch
Position
Off/Motion/Timer
Switch Position
Switch in this position will operate the
Kill Light® dusk-to-dawn timer. The light
will turn on at dusk and run for selected
amount of time.
Duration After
Motion Trigger
3 Minutes
Duration After
Dusk Trigger
4 Hour
Dip Switch
Position
Off/Motion/Timer
Switch Position
Duration After
Motion Trigger
5 Minute
Duration After
Dusk Trigger
6 Hour
2 Minutes
Duration After
Dusk Trigger
It is important to reset the light by moving
this switch to the OFF position before making changes to the Motion - Timer dip switch
on the inside of the light.
Duration After
Dusk Trigger
1 Hour
Dip Switch
Position
Off/Motion/Timer
Switch Position
Duration After
Motion Trigger
10 Minutes
Duration After
Dusk Trigger
10 Hour
Duration After
Motion Trigger
2 Hour
Dip Switch
Position
Off/Motion/Timer
Switch Position
Duration After
Motion Trigger
15 Minutes
Duration After
Dusk Trigger
All Night