UTMI+ Low Pin Interface (ULPI) Specification

Transcription

UTMI+ Low Pin Interface (ULPI)
Specification
Revision 1.1
October 20, 2004
UTMI+ Low Pin Interface Specification, Revision 1.1
October 20, 2004
Revision History
Revision
Issue Date
Comment
0.9
November 12, 2003
1.0rc1
January 3, 2004
Introduce PHY interface “modes”.
Update interface timings. Clarify 4-bit data clocking.
Clarify sending of RX CMD’s and interrupts.
Introduce AutoResume feature.
Route int pin to data(3) during 6-pin Serial Mode.
Explain VBUS thresholds.
Add T&MT diagram and updated text.
Add new section to explain how PHY is aborted by Link.
Various clarifications.
1.0rc2
January 13, 2004
Add block diagram.
Tighten interface timing.
Modify suspend protocol to more closely resemble UTMI.
Add SPKR_L and SPKR_MIC to signal list and T&MT
connector.
Various clarifications.
1.0rc3
January 19, 2004
Specify that PHY must send RX CMD after Reset.
Link + PHY clock startup time of no more than 5.6ms for a
peripheral is now mandatory.
PHY output delay reduced from 10ns to 9ns.
Added link decision time numbers for low speed.
Various Clarifications.
1.0
February 2, 2004
1.0rc3 adopted as 1.0 release.
1.1rc1
September 1, 2004
Various clarifications and fixes to hold time numbers, sending
RXCMDs, FsLsSerialMode, Vbus control and monitoring,
Test_J and Tesk_K signalling, Low Power Mode,
Hostdisconnect, ID detection, HS SOF packets, interrupts,
Carkit Mode, interface protection, No SYNC/EOP mode,
linestate filtering, and AutoResume.
1.1rc2
October 4, 2004
Re-arranged text in section 3.8.7.3. Updated contributors list.
1.1
October 20, 2004
1.1rc2 adopted as 1.1 release.
Pre-release.
The present Specification has been circulated for the sole benefit of legally-recognized Promoters,
Adopters and Contributors of the Specification. All rights are expressly reserved, including but not
limited to intellectual property rights under patents, trademarks, copyrights and trade secrets. The
respective Promoter's, Adopter's or Contributor's agreement entered into by Promoters, Adopters
and Contributors sets forth their conditions of use of the Specification.
ii
October 20, 2004
Promoters
ARC International Inc.
Conexant Systems, Inc.
Mentor Graphics Corporation
Philips
SMSC
TransDimension, Inc.
Contributors
Bart Vertenten
Batuhan Okur
Bill Anderson
Bill McInerney
Brian Booker
Chris Belanger
Chris Kolb
Chris Schell
Chung Wing Yan
Dave Sroka
David Wang
David Wooten
Eric Kawamoto
Farran Mackay
Frank Frazier
Fred Roberts
Hassan Farooq
Hyun Lee
Ian Parr
Jay Standiford
Jerome Tjia
Mark Saunders
Mohamed Benromdhane
Morgan Monks
Nabil Takla
Peter Tengstrand
Ramanand Mandayam
Rob Douglas
Saleem Mohamed
Shaun Reemeyer
Simon Nguyen
Subramanyam Sankaran
Sue Vining
Terry Remple
Timothy Chen
Vincent Chang
Philips
Philips
Motorola
TransDimension
Cypress
ARC
ARC
Philips
Philips
Philips
Philips
TransDimension
SMSC
Philips
Conexant
Synopsys
Conexant
TransDimension
Mentor
TransDimension
Philips
Mentor
Conexant
SMSC
ISI
ARC
Conexant
Mentor
Synopsys
Philips (Author)
Cypress
Philips
Texas Instruments
Qualcomm
Conexant
Conexant
Questions should be emailed to lpcwg@boardrooms.org.
iii
October 20, 2004
Table of Contents
1.
Introduction..............................................................................................................................................1
1.1 General...........................................................................................................................................1
1.2 Naming Convention........................................................................................................................1
1.3 Acronyms and Terms .....................................................................................................................1
1.4 References .....................................................................................................................................1
2.
Generic Low Pin Interface ......................................................................................................................2
2.1 General...........................................................................................................................................2
2.2 Signals............................................................................................................................................2
2.3 Protocol ..........................................................................................................................................3
2.3.1 Bus Ownership ..................................................................................................................3
2.3.2 Transferring Data ..............................................................................................................3
2.3.3 Aborting Data ....................................................................................................................4
3.
UTMI+ Low Pin Interface.........................................................................................................................5
3.1 General...........................................................................................................................................5
3.2 Signals............................................................................................................................................6
3.3 Block Diagram ................................................................................................................................7
3.4 Modes.............................................................................................................................................9
3.5 Power On and Reset ....................................................................................................................10
3.6 Interrupt Event Notification ...........................................................................................................10
3.7 Timing...........................................................................................................................................11
3.7.1 Clock ...............................................................................................................................11
3.7.2 Control and Data .............................................................................................................13
3.8 Synchronous Mode ......................................................................................................................15
3.8.1 ULPI Command Bytes.....................................................................................................15
3.8.2 USB Packets ...................................................................................................................18
3.8.3 Register Operations ........................................................................................................30
3.8.4 Aborting ULPI Transfers..................................................................................................37
3.8.5 USB Operations ..............................................................................................................39
3.8.6 Vbus Power Control (internal and external) ....................................................................52
3.8.7 OTG Operations ..............................................................................................................52
3.9 Low Power Mode..........................................................................................................................55
3.9.1 Data Line Definition For Low Power Mode .....................................................................55
3.9.2 Entering Low Power Mode ..............................................................................................55
3.9.3 Exiting Low Power Mode.................................................................................................56
3.9.4 False Resume Rejection .................................................................................................57
3.10 Full Speed / Low Speed Serial Mode (Optional)..........................................................................58
3.10.1 Data Line Definition For FsLsSerialMode .......................................................................58
3.10.2 Entering FsLsSerialMode................................................................................................59
3.10.3 Exiting FsLsSerialMode ..................................................................................................60
3.11 Carkit Mode (Optional) .................................................................................................................61
3.12 Safeguarding PHY Input Signals..................................................................................................62
4.
Registers ................................................................................................................................................65
4.1 Register Map ................................................................................................................................65
4.2 Immediate Register Set................................................................................................................67
4.2.1 Vendor ID and Product ID ...............................................................................................67
4.2.2 Function Control ..............................................................................................................68
4.2.3 Interface Control..............................................................................................................69
4.2.4 OTG Control ....................................................................................................................71
4.2.5 USB Interrupt Enable Rising ...........................................................................................72
4.2.6 USB Interrupt Enable Falling...........................................................................................73
4.2.7 USB Interrupt Status .......................................................................................................74
4.2.8 USB Interrupt Latch.........................................................................................................75
4.2.9 Debug ..............................................................................................................................76
4.2.10 Scratch Register..............................................................................................................76
4.2.11 Carkit Control ..................................................................................................................77
4.2.12 Carkit Interrupt Delay ......................................................................................................77
iv
4.3
4.4
5.
October 20, 2004
4.2.13 Carkit Interrupt Enable ....................................................................................................78
4.2.14 Carkit Interrupt Status .....................................................................................................78
4.2.15 Carkit Interrupt Latch.......................................................................................................79
4.2.16 Carkit Pulse Control ........................................................................................................79
4.2.17 Transmit Positive Width ..................................................................................................80
4.2.18 Transmit Negative Width.................................................................................................80
4.2.19 Receive Polarity Recovery ..............................................................................................80
4.2.20 Reserved .........................................................................................................................81
4.2.21 Access Extended Register Set........................................................................................81
4.2.22 Vendor-specific................................................................................................................81
Extended Register Set .................................................................................................................81
Register Settings for all Upstream and Downstream signalling modes.......................................81
T&MT Connector ...................................................................................................................................83
5.1 General.........................................................................................................................................83
5.2 Daughter-card (UUT) Specification ..............................................................................................83
v
October 20, 2004
Figures
Figure 1 – LPI generic data bus ownership......................................................................................................3
Figure 2 – LPI generic data transmit followed by data receive ........................................................................3
Figure 3 – Link asserts stp to halt receive data................................................................................................4
Figure 4 – Creating a ULPI system using wrappers.........................................................................................5
Figure 5 – Block diagram of ULPI PHY ............................................................................................................7
Figure 6 – Jitter measurement planes............................................................................................................12
Figure 7 – ULPI timing diagram......................................................................................................................13
Figure 8 – Clocking of 4-bit data interface compared to 8-bit interface .........................................................14
Figure 9 – Sending of RX CMD ......................................................................................................................17
Figure 10 – USB data transmit (NOPID) ........................................................................................................18
Figure 11 – USB data transmit (PID)..............................................................................................................19
Figure 12 – PHY drives an RX CMD to indicate EOP (FS/LS LineState timing not to scale)........................20
Figure 13 – Forcing a full/low speed USB transmit error (timing not to scale)...............................................21
Figure 14 – USB receive while dir was previously low...................................................................................22
Figure 15 – USB receive while dir was previously high .................................................................................23
Figure 16 – USB receive error detected mid-packet ......................................................................................24
Figure 17 – USB receive error during the last byte ........................................................................................25
Figure 18 – USB HS, FS, and LS bit lengths with respect to clock................................................................26
Figure 19 – HS transmit-to-transmit packet timing.........................................................................................29
Figure 20 – HS receive-to-transmit packet timing. .........................................................................................29
Figure 21 – Register write ..............................................................................................................................30
Figure 22 – Register read...............................................................................................................................31
Figure 23 – Register read or write aborted by USB receive during TX CMD byte.........................................31
Figure 24 – Register read turnaround cycle or Register write data cycle aborted by USB receive...............32
Figure 25 – USB receive in same cycle as register read data. USB receive is delayed................................33
Figure 26 – Register read followed immediately by a USB receive ...............................................................33
Figure 27 – Register write followed immediately by a USB receive during stp assertion ..............................34
Figure 28 – Register read followed by a USB receive ...................................................................................34
Figure 29 – Extended register write ...............................................................................................................35
Figure 30 – Extended register read................................................................................................................35
Figure 31 – Extended register read aborted by USB receive during extended address cycle ......................36
Figure 32 – PHY aborted by Link asserting stp. Link performs register write or USB transmit. ....................37
Figure 33 – PHY aborted by Link asserting stp. Link performs register read. ...............................................38
Figure 34 – Link aborts PHY. Link fails to drive a TX CMD. PHY re-asserts dir............................................38
Figure 35 – Hi-Speed Detection Handshake (Chirp) sequence (timing not to scale) ....................................40
Figure 36 – Preamble sequence (D+/D- timing not to scale) .........................................................................41
Figure 37 – LS Suspend and Resume (timing not to scale) ..........................................................................43
Figure 38 – FS Suspend and Resume (timing not to scale) ..........................................................................44
Figure 39 – HS Suspend and Resume (timing not to scale)..........................................................................46
Figure 40 – Low Speed Remote Wake-Up from Low Power Mode (timing not to scale) ..............................47
Figure 41 – Full Speed Remote Wake-Up from Low Power Mode (timing not to scale) ...............................48
Figure 42 – Hi-Speed Remote Wake-Up from Low Power Mode (timing not to scale) .................................49
Figure 43 – Automatic resume signalling (timing not to scale) ......................................................................50
Figure 44 – USB packet transmit when OpMode is set to 11b. .....................................................................51
Figure 45 – RX CMD VA_VBUS_VLD ≤ Vbus indication source ........................................................................54
Figure 46 – Entering low power mode............................................................................................................55
Figure 47 – Exiting low power mode when PHY provides output clock .........................................................56
Figure 48 – Exiting low power mode when Link provides input clock ............................................................56
Figure 49 – PHY stays in Low Power Mode when stp de-asserts before clock starts...................................57
Figure 50 – PHY re-enters Low Power Mode when stp de-asserts before dir de-asserts.............................57
Figure 51 – Interface behaviour when entering Serial Mode and clock is powered down.............................59
Figure 52 – Interface behaviour when entering Serial Mode and clock remains powered ............................59
Figure 53 – Interface behaviour when exiting Serial Mode and clock is not running.....................................60
Figure 54 – Interface behaviour when exiting Serial Mode and clock is running...........................................60
Figure 55 – PHY interface protected when the clock is running ....................................................................62
Figure 56 – Power up sequence when PHY powers up before the link. Interface is protected.....................63
Figure 57 – PHY automatically exits Low Power Mode with interface protected...........................................63
Figure 58 – Link resumes driving ULPI bus and asserts stp because clock is not running...........................64
vi
October 20, 2004
Figure 59 – Power up sequence when link powers up before PHY (ULPI 1.0 compliant links) ....................64
Figure 60 – Recommended daughter-card configuration (not to scale) ........................................................83
vii
October 20, 2004
Tables
Table 1 – LPI generic interface signals ............................................................................................................2
Table 2 – PHY interface signals .......................................................................................................................6
Table 3 – Mode summary.................................................................................................................................9
Table 4 – Clock timing parameters.................................................................................................................11
Table 5 – ULPI interface timing ......................................................................................................................13
Table 6 – Transmit Command (TX CMD) byte format ...................................................................................15
Table 7 – Receive Command (RX CMD) byte format ....................................................................................16
Table 8 – USB specification inter-packet timings...........................................................................................26
Table 9 – PHY pipeline delays .......................................................................................................................27
Table 10 – Link decision times .......................................................................................................................28
Table 11 – OTG Control Register power control bits .....................................................................................52
Table 12 – Vbus comparator thresholds ........................................................................................................52
Table 13 – RX CMD VbusValid over-current conditions ................................................................................53
Table 14 – Vbus indicators in the RX CMD required for typical applications.................................................54
Table 15 – Interface signal mapping during Low Power Mode ......................................................................55
Table 16 – Serial Mode signal mapping for 6-pin FsLsSerialMode ...............................................................58
Table 17 – Serial Mode signal mapping for 3-pin FsLsSerialMode ...............................................................58
Table 18 – Carkit signal mapping...................................................................................................................61
Table 19 – Register map ................................................................................................................................66
Table 20 – Register access legend ................................................................................................................67
Table 21 – Vendor ID and Product ID register description ............................................................................67
Table 22 – Function Control register ..............................................................................................................68
Table 23 – Interface Control register..............................................................................................................70
Table 24 – OTG Control register ....................................................................................................................71
Table 25 – USB Interrupt Enable Rising register ...........................................................................................72
Table 26 – USB Interrupt Enable Falling register...........................................................................................73
Table 27 – USB Interrupt Status register .......................................................................................................74
Table 28 – USB Interrupt Latch register.........................................................................................................75
Table 29 – Rules for setting Interrupt Latch register bits ...............................................................................75
Table 30 – Debug register ..............................................................................................................................76
Table 31 – Scratch register ............................................................................................................................76
Table 32 – Carkit Control Register .................................................................................................................77
Table 33 – Carkit Interrupt Delay register ......................................................................................................77
Table 34 – Carkit Interrupt Enable register ....................................................................................................78
Table 35 – Carkit Interrupt Status Register ....................................................................................................78
Table 36 – Carkit Interrupt Latch register.......................................................................................................79
Table 37 – Carkit Pulse Control .....................................................................................................................79
Table 38 – Transmit Positive Width................................................................................................................80
Table 39 – Transmit Negative Width ..............................................................................................................80
Table 40 – Receive Polarity Recovery ...........................................................................................................81
Table 41 – Upstream and downstream signalling modes ..............................................................................82
Table 42 – T&MT connector pin view.............................................................................................................84
Table 43 – T&MT connector pin allocation.....................................................................................................84
Table 44 – T&MT pin description ...................................................................................................................85
viii
1.
October 20, 2004
Introduction
1.1
General
This specification defines a generic PHY interface in Chapter 2.
In Chapter 3, the generic interface is applied to the UTMI+ protocol, reducing the pin count for discrete USB
transceiver implementations supporting On-The-Go, host, and peripheral application spaces.
1.2
Naming Convention
Emphasis is placed on normal descriptive text using underlined Arial font, e.g. must.
Signal names are represented using the lowercase bold Arial font, e.g. clk.
Registers are represented using initial caps, bold Arial font, e.g. OTG Control.
Register bits are represented using initial caps, bold italic Arial font, e.g. USB Interrupt Enable Falling.
1.3
Acronyms and Terms
A-device
B-device
DRD
FPGA
FS
HNP
HS
Link
LPI
LS
OTG
PHY
PLL
SE0
SIE
SRP
T&MT
ULPI
USB
USB-IF
UTMI
UUT
1.4
[Ref 1]
[Ref 2]
[Ref 3]
[Ref 4]
[Ref 5]
[Ref 6]
[Ref 7]
Device with a Standard-A or Mini-A plug inserted into its receptacle
Device with a Standard-B or Mini-B plug inserted into its receptacle
Dual-Role Device
Field Programmable Gate Array
Full Speed
Host Negotiation Protocol
Hi-Speed
ASIC, SIE, or FPGA that connects to an ULPI transceiver
Low Pin Interface
Low Speed
On-The-Go
Physical Layer (Transceiver)
Phase Locked Loop
Single Ended Zero
Serial Interface Engine
Session Request Protocol
Transceiver and Macrocell Tester
UTMI+ Low Pin Interface
Universal Serial Bus
USB Implementers Forum
USB 2.0 Transceiver Macrocell Interace
Unit Under Test
References
Universal Serial Bus Specification, Revision 2.0
On-The-Go Supplement to the USB 2.0 Specification, Revision 1.0a
USB 2.0 Transceiver Macrocell Interface (UTMI) Specification, v1.05
UTMI+ Specification, Revision 1.0
CEA-2011, OTG Transceiver Specification
CEA-936A, Mini-USB Analog Carkit Interface Specification
USB 2.0 Transceiver and Macrocell Tester (T&MT) Interface Specification, Version 1.2
1
2.
October 20, 2004
Generic Low Pin Interface
2.1
General
This section describes a generic low pin interface (LPI) between a Link and a PHY. Interface signals are
defined and the basic communication protocol is described. The generic interface can be used as a common
starting point for defining multiple application-specific interfaces.
Chapter 3 defines the UTMI+ Low Pin Interface (ULPI), which is based on the generic interface described
here. For ULPI implementations, the definitions in chapter 3 over-ride anything defined in chapter 2.
2.2
Signals
The LPI transceiver interface signals are described in Table 1. The interface described here is generic, and
can be used to transport many different data types. Depending on the application, the data stream can be
used to transmit and receive packets, access a register set, generate interrupts, and even redefine the
interface itself. All interface signals are synchronous when clock is toggling, and asynchronous when clock
is not toggling. Data stream definition is application-specific and should be explicitly defined for each
application space for inter-operability.
Control signals dir, stp, and nxt are specified with the assumption that the PHY is the master of the data
bus. If required, an implementation can define the Link as the master. If the Link is the master of the
interface, the control signal direction and protocol must be reversed.
Signal
Direction
Description
PHY Interface
clock
data
dir
stp
nxt
I/O
Interface clock. Both directions are allowed. All interface signals are
synchronous to clock.
I/O
Bi-directional data bus, driven low by the Link during idle. Bus ownership is
determined by dir. The Link and PHY initiate data transfers by driving a nonzero pattern onto the data bus. LPI defines interface timing for single-edge
data transfers with respect to rising edge of clock. An implementation may
optionally define double-edge data transfers with respect to both rising and
falling edges of clock.
OUT
Direction. Controls the direction of the data bus. When the PHY has data to
transfer to the Link, it drives dir high to take ownership of the bus. When the
PHY has no data to transfer it drives dir low and monitors the bus for Link
activity. The PHY pulls dir high whenever the interface cannot accept data
from the Link. For example, when the internal PHY PLL is not stable.
IN
Stop. The Link asserts this signal for 1 clock cycle to stop the data stream
currently on the bus. If the Link is sending data to the PHY, stp indicates the
last byte of data was on the bus in the previous cycle. If the PHY is sending
data to the Link, stp forces the PHY to end its transfer, de-assert dir and
relinquish control of the the data bus to the Link.
OUT
Next. The PHY asserts this signal to throttle the data. When the Link is
sending data to the PHY, nxt indicates when the current byte has been
accepted by the PHY. The Link places the next byte on the data bus in the
following clock cycle. When the PHY is sending data to the Link, nxt indicates
when a new byte is available for the Link to consume.
Table 1 – LPI generic interface signals
2
2.3
2.3.1
October 20, 2004
Protocol
Bus Ownership
The PHY is the master of the LPI bi-directional data bus. Ownership of the data bus is determined by the dir
signal from the PHY, as shown in Figure 1. When dir is low, the Link can drive data on the bus. When dir is
high, the PHY can drive data on the bus. A change in dir causes a turnaround cycle on the bus during
which, neither Link nor PHY can drive the bus. Data during the turnaround cycle is undefined and must be
ignored by both Link and PHY.
The dir signal can be used to directly control the data output buffers of both PHY and Link.
clock
data
turn
around
Link data
turn
around
PHY data
Link data
dir
Figure 1 – LPI generic data bus ownership
2.3.2
Transferring Data
As shown in the first half of Figure 2, the Link continuously drives the data bus to 00h during idle. The Link
transmits data to the PHY by driving a non-zero value on the data bus. To signal the end of data
transmission, the Link asserts stp in the cycle following the last data byte.
In the second half of Figure 2, the Link receives data when the PHY asserts dir. The PHY asserts dir only
when it has data to send to the Link, and keeps dir low at all other times. The PHY drives data to the Link
after the turnaround cycle.
The nxt signal can be used by the PHY to throttle the data during transmit and receive. During transmit, nxt
may be asserted in the same cycle that the Link asserts stp.
Transmit
Receive
clock
data
D0
D1
turn
around
D0
D1
turn
around
dir
stp
nxt
Figure 2 – LPI generic data transmit followed by data receive
3
2.3.3
October 20, 2004
Aborting Data
The PHY can assert dir to interrupt any data being transmitted by the Link. If the Link needs to interrupt data
being received from the PHY, it asserts stp for one clock cycle, as shown in Figure 3. This causes the PHY
to unconditionally1 de-assert dir and accept a complete data transmit from the Link. The PHY may re-assert
dir again only when the data transmit from the Link has completed.
clock
data
D2
D3
D4
turn
around
D0
D1
dir
stp
nxt
Figure 3 – Link asserts stp to halt receive data
1
4
The PHY will not de-assert dir if the ULPI interface is not usable. For example, if the internal PLL is not stable.
3.
3.1
October 20, 2004
UTMI+ Low Pin Interface
General
This section describes how any UTMI+ core can be wrapped to convert it to the smaller LPI interface. The
generic interface described in chapter 2 is used as a starting point. This section always over-rides anything
stated in chapter 2. While this specification details support of UTMI+ Level 3, PHY implementers may
choose to support any of the Levels defined in UTMI+.
ULPI defines a PHY to Link interface of 8 or 12 signals that allows a lower pin count option for connecting to
an external transceiver that may be based on the UTMI+ specification. The pin count reduction is achieved
by having relatively static UTMI+ signals be accessed through registers and by providing a bi-directional
data bus that carries USB data and provides a means of accessing register data on the ULPI transceiver.
This specification relies on concepts and terminology that are defined in the UTMI+ specification [Ref 4].
Specifically, if a ULPI PHY design is based on an internal UTMI+ core, then that core must implement the
following UTMI+ features.
Linestate must accurately reflect D+/D- to within 2-3 clocks. It is up to individual Link designers to
use Linestate to time bus events.
Filtering to prevent spurious SE0/SE1 states appearing on Linestate due to skew between D+ and
D-. Filtering of 14 clock cycles is required in Low Speed, and 2 clock cycles in Full Speed and HiSpeed modes.
The PHY must internally block the USB receive path during transmit. The receive path can be
unblocked when the internal Squelch (HS) or SE0-to-J (FS/LS) is seen.
TxReady must be used for all types of data transmitted, including Chirp.
Due to noise on the USB, it is possible that RxActive asserts and then de-asserts without any valid
data being received, and RxValid will not assert. The Link should operate normally with these dataless RxActive assertions.
As shown in Figure 4, a PHY or Link based on this specification can be implemented as an almost
transparent wrapper around existing UTMI+ IP cores, preserving the original UTMI+ packet timing, while
reducing pin count and leaving all functionality intact. This should not be taken to imply that other
implementations are not possible.
OTG/Host/Peripheral Core (Link)
UTMI+
Link Core
ULPI Link
Wrapper
ULPI Transceiver (PHY)
ULPI Interface
ULPI PHY
Wrapper
UTMI+ PHY
Core
USB
Register
Map
Figure 4 – Creating a ULPI system using wrappers
5
3.2
October 20, 2004
Signals
Table 2 describes the ULPI interface on the PHY. The PHY is always the master of the ULPI bus. USB and
Miscellaneous signals may vary with each implementation and are given only as a guide to PHY designers.
Signal
Direction
Description
PHY Interface
clock
data
I/O
I/O
Interface clock. The PHY must be capable of providing a 60MHz output clock.
Support for an input 60MHz clock is optional. If the PHY supports both clock
directions, it must not use the ULPI control and data signals for setting the
clock direction.
Data bus. Driven to 00h by the Link when the ULPI bus is idle. Two bus
widths are allowed:
•
8-bit data timed on rising edge of clock.
•
(Optional) 4-bit data timed on rising and falling edges of clock.
dir
OUT
Controls the direction of the data bus2. The PHY pulls dir high whenever the
interface cannot accept data from the Link. For example, when the internal
PLL is not stable. This applies whether Link or PHY is the clock source.
stp
IN
The Link must assert stp to signal the end of a USB transmit packet or a
register write operation, and optionally to stop any receive. The stp signal
must be asserted in the cycle after the last data byte is presented on the bus.
OUT
The PHY asserts nxt to throttle all data types, except register read data and
the RX CMD. Identical to RxValid during USB receive, and TxReady during
USB transmit. The PHY also asserts nxt and dir simultaneously to indicate
USB receive activity (RxActive), if dir was previously low. The PHY is not
allowed to assert nxt during the first cycle of the TX CMD driven by the Link.
nxt
USB Interface
D+
I/O
D+ pin of the USB cable. Required.
D-
I/O
D- pin of the USB cable. Required.
ID
IN
ID pin of the USB cable. Required for OTG-capable PHY’s.
VBUS
I/O
VBUS pin of the USB cable. Required for OTG-capable PHY’s. Required for
driving VBUS and the VBUS comparators.
Miscellaneous
XI
IN
Crystal input pin. Vendors should specify supported crystal frequencies.
XO
OUT
Crystal output pin.
C+
I/O
Positive terminal of charge pump capacitor.
C-
I/O
Negative terminal of charge pump capacitor.
SPKR_L
IN
Optional Carkit left/mono speaker input signal.
SPKR_MIC
I/O
Optional Carkit right speaker input or microphone output signal.
RBIAS
I/O
Bias current resistor.
Table 2 – PHY interface signals
2
UTMI+ wrapper developers should note that data bus control has been reversed from UTMI to ensure that USB data
reception is not interrupted by the Link.
6
3.3
October 20, 2004
Block Diagram
An example block diagram of a ULPI PHY is shown in Figure 5. This example is based on an internal
UTMI+ Level 3 core [Ref 4], which can interface to peripheral, host, and On-The-Go Link cores. A
description of each major block is given below.
ULPI Transceiver (PHY)
ULPI PHY
Wrapper
UTMI+ Level 3 PHY core
Reset
CLK
DataIn(7:0)
DataOut(7:0)
TXValid
TXReady
RXActive
RXValid
RXError
clock
data(7:0) or data(3:0)
ULPI
Interface
dir
stp
nxt
SuspendM
XcvrSelect(1:0)
TermSelect
OpMode(1:0)
LineState(1:0)
HostDisconnect
IdPullup
IdDig
DpPulldown
DmPulldown
DrvVbus
ChrgVbus
DischrgVbus
BValid
AValid
VbusValid
SessEnd
FsLsSerialMode
Tx_Enable_N
Tx_DAT
Tx_SE0
Rx_DP
Rx_DM
Rx_RCV
Register Map
D+
USB 2.0
ATX
DID
ID Detector
USB
Cable
VBUS
Vbus
Sensors
SRP
Charge &
Discharge
Charge
Pump
Supply
C+
C-
Charge
Pump
Capacitor
Digital
Logic
TxBitstuffEnable
DrvVbusExternal
VbusValidExternal
Car Kit Option
SPKR_L
SPKR_L
SPKR_MIC
SPKR_R
Carkit Interrupt
Detectors
XI
Crystal
Oscillator
XO and PLL
MIC
RBIAS
General Biasing
Power-On-Reset
Figure 5 – Block diagram of ULPI PHY
7
October 20, 2004
UTMI+ Level 3 PHY core
The ULPI PHY may contain a core that is compliant to any UTMI+ level [Ref 4]. Signals for 16-bit data buses
are not supported in ULPI. While Figure 5 shows the typical blocks for a Level 3 UTMI+ core, the PHY
vendor must specify the intended UTMI+ level, and provide the functionality necessary for compliance to that
level.
ULPI PHY Wrapper
The ULPI PHY wrapper of Figure 5 reduces the UTMI+ interface to the Low Pin Interface described in this
document. All signals shown on the UTMI+ Level 3 PHY core are reduced to the ULPI interface signals
clock, data, dir, stp, and nxt. The Register Map stores the relatively static signals of the UTMI+ interface.
Crystal Oscillator and PLL
When a crystal is attached to the PHY, the internal clock(s) and the external 60MHz interface clock are
generated from the internal PLL. When no crystal is attached, the PHY may optionally generate the internal
clock(s) from an input 60MHz clock provided by the Link.
General Biasing
Internal analog circuits require an accurate bias current. This is typically generated using an external,
accurate reference resistor.
DrvVbusExternal and ExternalVbusIndicator
The PHY may optionally control an external VBUS power source via the optional pin DrvVbusExternal. For
example, the external supply could be a charge pump or 5V power supply controlled using a power switch.
The external supply is controlled by the DrvVbus and the optional DrvVbusExternal bits in the OTG
Control register. The polarity of the DrvVbusExternal output pin is implementation dependent.
If control of an external VBUS source is provided the PHY may optionally provide for a VBUS power source
feed back signal on the optional pin ExternalVbusIndicator. If this pin is provided, the use of the pin is
defined by the optional control bits in the OTG Control and Interface Control registers. See Section 3.8.6.3
for further detail.
Power-On-Reset
A power-on-reset circuit must be provided in the PHY. When power is first applied to the PHY, the power-onreset will reset all circuitry and leave the ULPI interface in a usable state.
Carkit Option
The PHY may optionally support Carkit Mode [Ref 6]. While in Carkit Mode, the PHY routes speaker and
microphone signals between the Link and the USB cable. In carkit mono mode, SPKR_L inputs a mono
speaker signal and SPKR_MIC outputs the microphone signal, MIC. In carkit stereo mode, SPKR_L inputs
the left speaker signal, and SPKR_MIC inputs the right speaker signal, SPKR_R.
8
3.4
October 20, 2004
Modes
The ULPI interface can operate in one of five independent modes listed in Table 3. The interface is in
Synchronous Mode by default. Other modes are enabled by bits in the Function Control and Interface
Control registers. In Synchronous Mode, the data bus carries commands and data. In other modes, the data
pins are redefined with different functionality. Synchronous Mode and Low Power Mode are mandatory.
Mode Name
Mode Description
Synchronous Mode
This is the normal mode of operation. The clock is running and is stable
with the characteristics defined in section 3.6. The ULPI interface carries
commands and data that are synchronous to clock.
Low Power Mode
The PHY is powered down with the clock stopped. The PHY keeps dir
asserted, and the data bus is redefined to carry LineState and interrupts.
See section 3.9 for more information.
6-pin FS/LS Serial Mode
(optional)
The data bus is redefined to 6-pin serial mode, including 6 pins to transmit
and receive serial USB data, and 1 pin to signal interrupt events. The clock
can be enabled or disabled. This mode is valid only for implementations
with an 8-bit data bus. See section 3.10 for more information.
3-pin FS/LS Serial Mode
(optional)
The data bus is redefined to 3-pin serial mode, including 3 pins to transmit
and receive serial USB data, and 1 pin to signal interrupt events. The clock
can be enabled or disabled. See section 3.10 for more information.
Carkit Mode
(optional)
The data bus is redefined to Carkit mode [Ref 6], including 2 pins for serial
UART data, and 1 pin to signal interrupt events. The clock may optionally
be stopped. See section 3.11 for more information.
Table 3 – Mode summary
9
3.5
October 20, 2004
Power On and Reset
The ULPI PHY provides an internal power-on reset circuit that resets all logic, including the UTMI+ core,
ULPI interface and registers, on power-up.
After power-up, and when the clock starts toggling, the Link must reset the PHY by writing to the Reset bit in
the Function Control register. When this bit is set, the transceiver will assert dir and reset the digital core.
When the reset completes, the PHY de-asserts dir and automatically clears the Reset bit in the Function
Control register. After de-asserting dir, the PHY must immediately re-assert dir and send an RX CMD
update to the Link.
During reset, the data bus is driven by the PHY, however the data is undefined and must not be interpreted
by the Link. The Link must not attempt to access the PHY until the reset has completed and dir is deasserted. The ULPI interface and registers are not affected by Reset, unless otherwise stated in the register
definitions of chapter 4.
Further power up and reset requirements are outlined in section 3.12.
3.6
Interrupt Event Notification
In any mode, the PHY is able to detect interrupt events, and notify the link that an interrupt event has
occurred. Interrupt event notifications are enabled by the USB Interrupt Enable Rising, USB Interrupt
Enable Falling, and the Carkit Interrupt Enable registers. If an interrupt is enabled, the PHY must power
the needed circuitry regardless of which mode the PHY is in. The only exceptions are the HostDisconnect
interrupt which is valid only in Synchronous Mode, and the IdGnd interrupt which is controlled by IdPullup.
To ensure interrupts are detectable when clock is powered down, the link should enable both rising and
falling edges.
If the link is in Synchronous Mode, an interrupt event causes the PHY to send an RX CMD byte to the Link.If
the link is not in Synchronous Mode, an interrupt event causes the PHY to assert the int pin. When the Link
detects that int is asserted, it wakes up the clock (if powered down), and then reads the USB Interrupt
Latch and Carkit Interrupt Latch registers to determine the source of the interrupt.
10
3.7
Timing
3.7.1
Clock
October 20, 2004
Clock timing is summarized in Table 4. Timing for 8-bit peripherals are taken from UTMI [Ref 3]. New timing
has been added for the optional 4-bit interface. ULPI also introduces several new parameters that must be
filled in by the PHY vendor. If the PHY supports the optional input clock, then the Link clock must meet the
requirements of Table 4 and any vendor-specific requirements.
Parameter
Symbol
Min
Nominal
Max
8-bit ±10%
FSTART_8BIT
54
60
66
4-bit ±5%1
FSTART_4BIT
57
60
63
FSTEADY
59.97
60
60.03
8-bit ±10%
DSTART_8BIT
40
50
60
4-bit ±5%1
DSTART_4BIT
45
50
55
Duty Cycle (steady state) ±500ppm
DSTEADY
49.975
50
50.025
%
Time to reach steady state frequency and duty
cycle after first transition
TSTEADY
1.4
ms
Peripheral 2
TSTART_DEV
5.6
3
TSTART_HOST
Frequency (first transition)
Frequency (steady state) ±500ppm
Duty Cycle (first transition)
Clock startup time after deassertion of SuspendM
Host
Units
MHz
MHz
%
ms
PHY preparation time after first transition of
input clock 4
TPREP
us
Jitter
TJITTER
ps
TRISE/TFALL
ns
Rise and fall time
Table 4 – Clock timing parameters
1
4-bit clock frequency and duty cycle have been reduced by 5% to provide a usable falling edge of clock.
2
Peripheral clock startup time is calculated to meet chirp timing, and is taken from the UTMI specification
[Ref 3] section 5.22.2.3.
3
Host clock startup time must be filled in by the PHY vendor. A startup time of less than 1ms is
recommended to meet resume timing. If the PHY is used as a host and the interface clock cannot be
designed to be usable within 1ms, it must internally transmit resume signalling automatically. This is
illustrated in section 3.8.5.4.4.
4
If the PHY supports the optional input clock feature, the PHY vendor must state the preparation time. The
PHY must synchronize its PLL and be ready to accept a transmit command from the Link by the specified
time. This is illustrated in Figure 48. The Link clock startup time added to the PHY preparation time, must
meet the 5.6ms startup time for a peripheral (UTMI specification [Ref 3], section 5.22.2.3). A total startup
time of 1ms is recommended for a host.
11
3.7.1.1
October 20, 2004
Output Clock
The PHY must be capable of sourcing an output clock, and meet the requirements listed in Table 4.
Output clock timing for an 8-bit peripheral follows the UTMI specification [Ref 3]. The steady state frequency
(FSTEADY) provides ±500ppm accuracy as required by USB Hi-Speed data. The startup time (TSTART_DEV)
allows a peripheral to wake up its clock and finish transmitting a Chirp-K within the maximum allowed time of
7ms (TSTART_DEV + TSTEADY).
For a host with an 8-bit data bus, ULPI defines a new output clock startup time (TSTART_HOST). When a USB
host detects remote wake-up signalling, it must wake up its clock and start transmitting resume-K within the
maximum allowed time of 1ms. The PHY vendor must specify this value.
For the optional 4-bit data interface, both rising and falling edges are used to clock data. To provide a usable
falling edge, ULPI reduces frequency (FSTART_4BIT) and duty cycle (DSTART_4BIT) requirements by 5%.
In all cases, the output clock must be stopped when the PHY is suspended or when clock is not “usable”.
3.7.1.2
Input Clock (optional)
The PHY may optionally support a 60MHz input clock from the Link, removing the need for a crystal. The
PHY must drive its internal PLL from the 60MHz input clock.
PHY vendors are responsible for specifying the required input clock timing. The PHY vendor must state the
required tolerances on frequency, duty cycle, jitter, rise and fall times, as shown in Table 4. The internal PHY
clock preparation time, TPREP, must also be specified. If necessary, the requirements should include the
input capacitance, and the current sinking and sourcing capability.
The Link can choose to disable or shut down its PLL during Low Power Mode, and should not activate its
clock output until its PLL is stable. An unstable Link clock may cause the PHY PLL to take longer to
stabilize.
3.7.1.2.1
Input Clock Jitter
For the timing measurement planes shown in Figure 6, the USB Specification mandates a 7.5% jitter budget
on the Hi-Speed transmit eye diagram, measured at Connector A (TP2). A jitter budget of 5% is
recommended at the PHY pins (TP1). The ULPI specification does not specify the clock jitter requirement at
the Link output clock pin (TP0), however Link and PHY designers should minimize their clock jitter such that
the total of Link plus PHY jitter meets the recommended 5% jitter budget.
TP0
TP1
TP2
clock
LINK
USB CABLE
PHY
USB
CONNECTOR
USB OTG, Host or Peripheral Circuit Board
Figure 6 – Jitter measurement planes
12
3.7.2
October 20, 2004
Control and Data
Control and data timing requirements are given in Table 5 and illustrated in Figure 7. These timings apply to
Synchronous Mode only. All timings are measured with respect to the clock as seen at the PHY clock pin.
Control signals and 8-bit data are always clocked on the rising edge of clock, while the optional double-edge
4-bit data signals are clocked on rising and falling edges.
clock
TSC
THC
Control In
(stp)
data In
(8-bit)
TSD
data In
(4-bit)
THD
TSDD
THDD
TSDD
THDD
Control out
(dir,nxt)
TDC
TDC
TDD
data out
(8-bit)
TDDD
TDDD
data out
(4-bit)
Figure 7 – ULPI timing diagram
Parameter
Symbol
Min
Max
Units
6.0
ns
Output clock
Setup time (control in, 8-bit data in)
TSC, TSD
Hold time (control in, 8-bit data in)
THC, THD
Output delay (control out, 8-bit data out)
TDC, TDD
9.0
ns
Setup time (4-bit data in) (optional)
TSDD
3.0
ns
Hold time (4-bit data in) (optional)
THDD
Output delay (4-bit data out) (optional)
TDDD
4.0
ns
Setup time (control in, 8-bit data in)
TSC, TSD
3.0
ns
Hold time (control in, 8-bit data in)
THC, THD
Output delay (control out, 8-bit data out)
TDC, TDD
6.0
ns
Setup time (4-bit data in)
TSDD
2.5
ns
Hold time (4-bit data in)
THDD
Output delay (4-bit data out)
TDDD
0.0
ns
-0.8
ns
Input clock (optional)
1.5
ns
0.8
ns
3.5
ns
Table 5 – ULPI interface timing
13
3.7.2.1
October 20, 2004
4-bit Data Clocking (optional)
The PHY may optionally support a 4-bit data bus instead of an 8-bit data bus. The original 8-bit data or
command is split into two 4-bit “nibbles”. The least significant nibble, data(3:0), is transferred first on the
rising edge of clock. The most significant nibble, data(7:4), is transferred second on the falling edge of
clock. Transferring an odd number of 4-bit nibbles is not allowed. The 4-bit data must be clocked as shown
in Figure 8. This ensures that a complete byte of data arrives at the same rising edge as 8-bit designs.
The Link and PHY must meet tighter timing as specified in Table 5 with respect to both rising and falling
edges. Both output and input clock directions are allowed.
The control signals dir, stp, and nxt are clocked only on the rising edge of the 60MHz interface clock
because data transfers are always byte-aligned.
Transmit
Receive
clock
data (8-bit)
data (4-bit)
D0
D1
D0L D0U D0L D0U D1L D1U
turn
around
turn
around
D0
D1
D0L D0U D1L D1U
dir
stp
nxt
Figure 8 – Clocking of 4-bit data interface compared to 8-bit interface
14
turn
around
turn
around
3.8
October 20, 2004
Synchronous Mode
This section describes the Synchronous Mode of the UTMI+ Low Pin Interface protocol. The rules of Chapter
2 always apply unless otherwise stated in this section. ULPI also defines a register map in the PHY that is
accessed by the Link.
3.8.1
ULPI Command Bytes
ULPI modifies the original UTMI data stream so that it can fit more data types. Redundancy in the PID byte
during transmit is overloaded with ULPI transmit commands (TX CMD). Unused data bytes in the receive
stream are overloaded with receive commands (RX CMD). ULPI defines a Transmit Command byte that is
sent by the Link and a Receive Command byte that is sent by the PHY.
3.8.1.1
Transmit Command Byte (TX CMD)
The Link initiates transfers to the PHY by sending the Transmit Command byte of Table 6 The TX CMD
byte consists of a 2-bit command code and a 6-bit payload.
Byte
Name
Command
Code
data(7:6)
Special
00b
Transmit
RegWrite
RegRead
01b
10b
11b
Command Payload
data(5:0)
000000b
(NOOP)
Command Description
No operation. 00h is the idle value of the data bus.
The Link drives NOOP by default.
XXXXXXb (RSVD)
Reserved command space. Values other than those
above will give undefined behavior.
000000b
(NOPID)
Transmit USB data that does not have a PID, such as
chirp and resume signalling. The PHY starts
transmitting on the USB beginning with the next data
byte.
00XXXXb
(PID)
Transmit USB packet. data(3:0) indicates USB
packet identifier PID(3:0).
XXXXXXb (RSVD)
Reserved Command space. Values other than those
above will give undefined behaviour.
101111b
Extended reqister write command. 8-bit address
available in the next cycle.
(EXTW)
XXXXXXb (REGW)
Register write command with 6-bit immediate
address.
101111b
Extended register read command. 8-bit address
available in the next cycle.
(EXTR)
XXXXXXb (REGR)
Register read command with 6-bit immediate
address.
Table 6 – Transmit Command (TX CMD) byte format
15
3.8.1.2
October 20, 2004
Receive Command Byte (RX CMD)
The Receive Command byte of Table 7 is sent by the PHY to update the Link with LineState, USB receive,
disconnect and OTG status information. VBUS thresholds are described in 3.8.7.3.
data
1:0
Name
Description and Value
LineState
UTMI+ LineState signals.
data(0) = LineState(0)
data(1) = LineState(1)
3:2
5:4
Vbus
State
RxEvent
Encoded Vbus Voltage state
Value
VBUS Voltage
SessEnd
SessValid
VbusValid3
00
VBUS < VB_SESS_END
1
0
0
01
VB_SESS_END ≤ VBUS < VSESS_VLD
0
0
0
10
VSESS_VLD ≤ VBUS < VA_VBUS_VLD
X
1
0
11
VA_VBUS_VLD ≤ VBUS
X
X
1
Encoded UTMI event signals
Value
RxActive
RxError
HostDisconnect4
00
0
0
0
01
1
0
0
11
1
1
0
10
X
X
1
6
ID
Set to the value of IdGnd (UTMI+ IdDig). Valid 50ms after IdPullup is set to 1b.
7
alt_int
Asserted when a non-USB interrupt occurs. This bit must be set when an unmasked
event occurs on any bit in the Carkit Interrupt Latch register. The Link must read the
Carkit Interrupt Latch register to determine the source of the interrupt.
Table 7 – Receive Command (RX CMD) byte format
3
The VbusValid indicator in the RX CMD comes from either the internal VbusValid comparator, or the external Vbus
indicator input.
4
Hostdisconnect state must be indicated to the Link only in host mode (DpPulldown and DmPulldown both set to 1b).
When in peripheral mode, Hostdisconnect must be ignored and must not mask events on RxActive or RxError.
16
3.8.1.3
October 20, 2004
When to send an RX CMD
An RX CMD is sent only in Synchronous Mode, and conveys two types of information to the Link. The first is
USB receive information. The second is interrupt events. All information is encoded into the single RX CMD
byte of Table 7.
USB receive information includes LineState, RxActive and RxError. The sending of RX CMD’s for USB
receive data is covered in 3.8.2.4. After a USB transmit, the PHY must send an RX CMD with LineState
indicating EOP to the Link. For Hi-Speed, an EOP is the !squelch to squelch transition on LineState. For Full
Speed and Low Speed, an EOP is the transition from SE0 to J on LineState. This is illustrated in section
3.8.2.2.
Interrupt events include Hostdisconnect, Vbus, IdGnd, and alternative sources such as Carkit interrupts.
An RX CMD is sent to the Link whenever these events are detected, and the corresponding USB Interrupt
Enable Rising or USB Interrupt Enable Falling registers are set.
Figure 9 illustrates how the PHY sends RX CMD information to the Link. The first packet shows a single RX
CMD. If back-to-back changes are detected, the PHY keeps dir asserted and drives back-to-back RX
CMD’s, as shown in the second packet of Figure 9. The Link must be able to accept any number of
continuous, back-to-back RX CMD’s.
An RX CMD has lower priority than USB receive and transmit data, but has higher priority than Register
Read and Write commands. If the ULPI bus is busy with USB data, the RX CMD will be queued in the PHY
and sent when the ULPI bus is available. When sent to the Link, a queued RX CMD must always convey the
current RX CMD values, not a previous or old value. The PHY must also send RX CMD’s to the Link when
nxt is de-asserted during USB receive packets.
ULPI Signals
clock
data[7:0]
turn
around
RX CMD
turn
around
turn
around
RX CMD
RX CMD
turn
around
dir
stp
nxt
Figure 9 – Sending of RX CMD
17
3.8.2
October 20, 2004
USB Packets
This section describes how USB packets are transmitted and received over the ULPI bus. Limits on PHY
and Link processing delays are given so that USB inter-packet delays can be met.
3.8.2.1
USB Data Transmit (NOPID)
As shown in Figure 10, to transmit data on the USB that does not contain a Packet Identifier (PID), the Link
sends a TX CMD byte of the NOPID type. The PHY must assert nxt to throttle the data coming from the
Link. The PHY must not assert nxt in the first cycle of the TX CMD, and must de-assert nxt when it detects
stp high. Since this command does not contain PID data, the PHY must wait for the next data byte before
beginning transmission on the USB. When the last byte has been consumed by the PHY, the Link asserts
stp for 1 cycle, and drives data to 00h if no transmit errors occurred. The Link must not assert stp before the
first byte has been consumed by the PHY.
This command must be used for chirp and resume signalling, which are detailed in sections 3.8.5.1 and
3.8.5.3, respectively. For such signalling, the OpMode bits in the Function Control register must first be set
to 10b. For chirp and resume signalling, the PHY does not need to insert stuff bits and so must hold nxt high
until it sees the stp pulse.
While the Link is driving the ULPI bus with a NOPID packet, the PHY should not assert dir unless it wants to
abort the packet. All RX CMD changes during the USB packet transmit must be replaced with a single RX
CMD update that is sent at the end of the USB transmit, when the ULPI bus is available. The RX CMD
update must always convey the current RX CMD values, not a previous or old value.
ULPI Signals
clock
data[7:0]
TX CMD
(NOPID)
D0
D1
D2
D0
D1
D2
dir
stp
nxt
UTMI+ Equivalent Signals
TxValid
TxReady
TxData[7:0]
Figure 10 – USB data transmit (NOPID)
18
3.8.2.2
October 20, 2004
USB Packet Transmit (PID)
As shown in Figure 11, to transmit a USB packet, the Link first drives a TX CMD byte. As in Table 6, the Link
sets the Command Code to 01b (Transmit), and places the USB Packet Identifier (PID) on data(3:0). The
PHY throttles the data using nxt such that the Link provides the next byte in the cycle after nxt is detected
as high. This is identical to UTMI’s DataIn and TxReady. When the last byte has been consumed by the
PHY, the Link asserts stp for 1 cycle, and drives data to 00h if no transmit errors occurred. The Link must
not assert stp before the first byte has been consumed by the PHY.
For all PID packets, the PHY must automatically prepend a SYNC pattern and append an EOP pattern. In
High Speed, when the PID field of the TX CMD is 5h, the PHY must recognize that this is a Start-Of-Frame
(SOF) packet and automatically append a long EOP.
After asserting stp, the Link cannot transmit another packet until the first packet has completed on the USB.
The Link must follow the packet timings given in section 3.8.2.6, however if an RX CMD indicating end-ofpacket (EOP) is received before the given timings, the Link can begin transmitting the next packet, as shown
in Figure 12. The PHY must always send the RX CMD indicating EOP.
While the Link is driving the ULPI bus with a PID packet, the PHY should not assert dir unless it wants to
abort the packet. All RX CMD changes during the USB packet transmit must be replaced with a single RX
CMD update that is sent at the end of the USB transmit, when the ULPI bus is available. The RX CMD
update must always convey the current RX CMD values, not a previous or old value.
As clarified in UTMI+ [Ref 4], the PHY must internally block the USB receive path during transmit.
ULPI Signals
clock
data[7:0]
TX CMD
(PID)
D1
D2
D3
PID
D1
D2
D3
dir
stp
nxt
TxValid
TxReady
TxData[7:0]
Figure 11 – USB data transmit (PID)
19
October 20, 2004
ULPI Signals
clock
data[7:0]
Other FS/LS RX CMD’s can occur here
(Hi-Speed)
data[7:0]
turn
around
(Full/Low Speed)
LineState
SE0
turn
around
turn
around
LineState
squelch
turn
around
turn
around
LineState
J
turn
around
dir
stp
nxt
LineState
(Hi-Speed)
LineState
(Full/Low Speed)
!squelch (01b)
J/K (10b/01b)
squelch (00b)
SE0 (00b)
J (10b)
TxValid
TxReady
TxData[7:0]
Figure 12 – PHY drives an RX CMD to indicate EOP (FS/LS LineState timing not to scale)
20
3.8.2.3
October 20, 2004
USB Transmit Error
If the Link experiences a buffer under-run during the transmission of a Full Speed or Low Speed USB
packet, it must insert a bit-stuff error into the packet before the packet ends. To force a transmit error, the
Link drives FFh onto data at the end of the packet, in the same cycle it asserts stp. This is shown as the
last, grey-colored data byte in Figure 11. The Link must drive no more than one byte to FFh, and the PHY
will automatically generate the Full Speed transmit error by sending a minimum of 8 consecutive 1’s on the
USB bus. The Link must wait for an RX CMD indicating the SE0-to-J transition before transmitting another
packet. The Link must not assert stp before the first byte has been consumed by the PHY.
This sequence replaces UTMI’s method of changing OpMode from 00b to 10b during the last byte of
transmission.
To force a Hi-Speed transmit error, the Link must transmit an inverted CRC at the end of the packet.
ULPI Signals
clock
data[7:0]
TX CMD
(PID)
D1
D2
D3
FFh
dir
stp
nxt
OpMode
10
00
00
TxValid
TxReady
TxData[7:0]
PID
D1
D2
D3
FFh
Figure 13 – Forcing a full/low speed USB transmit error (timing not to scale)
21
3.8.2.4
October 20, 2004
USB Packet Receive
As shown in Figure 14, when the PHY is receiving USB data, it first gains ownership of the data bus by
asserting dir. The PHY asserts dir in the same cycle that UTMI’s RxActive asserts. As shown in Figure 14,
if dir was previously low, the PHY will assert both dir and nxt so that the Link knows immediately that this is
a USB receive packet. If dir was previously high, as seen in Figure 15, the PHY will de-assert nxt and drive
an RX CMD with the RxEvent field set to 01b (RxActive state). The PHY can start driving data in the
following cycle, or will output RX CMD’s until USB data is available. Valid USB packet data is presented to
the Link by asserting nxt and placing a byte onto the bus. When nxt is low, the PHY drives the RX CMD
byte. All RX CMD changes during the USB packet receive must be signaled when nxt is low. If nxt is never
low during the packet receive, all RX CMD changes must be replaced with a single RX CMD update that is
sent at the end of the USB packet receive, when the ULPI bus is available. The RX CMD update must
always convey the current RX CMD values, not a previous or old value.
While the data stream has been modified from UTMI’s DataOut, nxt is identical to RxValid. The Link
considers a packet to be completed when the RX CMD byte shows RxActive is set to 0b, or dir is deasserted, whichever occurs first.
ULPI Signals
clock
data[7:0]
turn
around
RX CMD
PID
RX CMD
D1
D2
D3
D2
D3
dir
stp
nxt
RxActive
RxValid
RxData[7:0]
PID
D1
Figure 14 – USB receive while dir was previously low
22
turn
around
October 20, 2004
ULPI Signals
clock
data[7:0]
Previous
RX CMD
(RxActive)
RX CMD
PID
RX CMD
D1
D2
D3
D2
D3
turn
around
dir
stp
nxt
RxActive
RxValid
RxData[7:0]
PID
D1
Figure 15 – USB receive while dir was previously high
23
3.8.2.5
October 20, 2004
USB Receive Error
If the PHY detects a USB packet receive error, it ignores any currently received data byte, de-asserts nxt
and drives RX CMD bytes with the RxEvent field set to 11b (RxError state). The PHY de-asserts dir when
RxActive is de-asserted. The RxError state is identical to UTMI’s RxError signal.
All PHY implementations must set RxError when a Full Speed bit-stuff error is detected. The PHY can
optionally set RxError for a Hi-Speed EOP that is not aligned to a byte boundary, for data overflow, data
underflow, or another valid receive error condition. The PHY does not assert RxError for a single Full Speed
dribble bit prior to the EOP5.
Figure 16 shows the behaviour of the ULPI interface when a bit-stuff error is detected mid-packet. Figure 17
shows the behaviour when a bit-stuff error occurs in the final CRC byte.
The Link must ignore packets with a receive error.
ULPI Signals
clock
data[7:0]
turn
around
RX CMD
PID
D1
PID
D1
RX CMD
(RxError)
RX CMD
dir
stp
nxt
RxActive
RxValid
RxError
RxData[7:0]
Figure 16 – USB receive error detected mid-packet
5
For an explanation of dribble bit see USB Specification [Ref 1] 7.1.9.1.
24
RX CMD
turn
around
October 20, 2004
ULPI Signals
clock
data[7:0]
turn
around
RX CMD
PID
RX CMD
D1
D2
RX CMD
(RxError)
turn
around
dir
stp
nxt
RxActive
RxValid
RxError
RxData[7:0]
PID
D1
D2
Figure 17 – USB receive error during the last byte
25
3.8.2.6
October 20, 2004
USB Packet Timing
The USB specification [Ref 1] defines inter-packet timing. The ULPI specification relates these timings back
to the ULPI interface by specifying a budget of clock cycles available to the PHY and Link. The PHY must
process data within the given timing range. Similarly, the Link must respond within the given decision time,
or timeout if a response is not received within the given timing range. The following sections detail all
required ULPI inter-packet timing, and are derived from both the USB specification [Ref 1] and UTMI PHY
processing and synchronization delays6.
3.8.2.6.1
USB Inter-packet delay and Packet timeout
Table 8 is provided as background information. Full Speed inter-packet delays are measured from the SE0to-J transition of the first packet, to the start of the SYNC pattern on the second packet. Hi-Speed interpacket delays are measured from the time the bus enters the idle state at the end of the first packet, to the
time the bus leaves the idle state at the start of the second packet. There are 8 HS bit times in one clock
cycle, 5 clock cycles in one FS bit time, and 40 clock cycles in one LS bit time, as shown in Figure 18.
Packet Sequence
HS bit times
Definition
FS/LS bit times
Min
Max
Min
Max
Transmit-Transmit
(host only)
88
192
2
6.5
Two consecutive host packets must have an interpacket delay within this range.
Receive-Receive
(peripheral only)
32
-
2
-
Peripherals must be capable of receiving back-toback packets with this timing.
Receive-Transmit
(host or peripheral)
8
192
2
6.5
Host or peripheral receives a packet and must
transmit a response within the given timing range.
736
816
16
18
Host or peripheral transmits a packet and will
timeout within this range if a response is not
received7.
Transmit-Receive
Table 8 – USB specification inter-packet timings
clock
1 clock = 8 HS bit times
5 clocks = 1 FS bit time
40 clocks = 1 LS bit time
HS
D+/DFS
D+/DLS
D+/D-
Figure 18 – USB HS, FS, and LS bit lengths with respect to clock
6
PHY timings are taken from the UTMI Specification [Ref 3]. Implementers can refer to UTMI for architectural pointers.
Timing includes a maximally connected USB system consisting of a return trip through 6 USB cables, 5 external hubs,
and the downstream host or peripheral. Refer to USB specification 7.1.19 for more information.
7
26
3.8.2.6.2
October 20, 2004
PHY Pipeline Delays
Any PHY using the ULPI interface must comply to the timings given in Table 9. USB bus events are
measured relative to transitions on D+ and D- lines. ULPI interface timings are measured relative to the
clock edge on which the transition is detected (e.g. clock edge on which stp is detected by the PHY).
Parameter
Name
HS PHY
Delay
FS PHY
Delay
LS PHY
Delay
RX CMD Delay8
2-4
2-4
2-4
Number of clocks after a change in the internal USB bus
state is detected to an RX CMD byte being sent over the
ULPI bus. Applies to all changes except SE0.
2-4
4-6
16-18
Number of clocks between the USB bus indicating SE0 to
an RX CMD byte being sent over the ULPI bus. Delay is
increased due to filtering.
TX Start Delay
1-2
1-10
1-10
Number of clocks between the PHY detecting a TX CMD
on the ULPI bus to transmitting the first K of the SYNC
pattern on the USB bus.
TX End Delay
2-5
N/A
N/A
Number of clocks between the PHY detecting stp on the
ULPI bus to completing transmission of EOP on the USB
bus. Used for HS packets only. The Link can use TX End
Delay to calculate when the packet has completed
transmitting on the USB.
HS EOP is completed when all 8 consecutive 1’s have
finished transmitting on the USB bus.
FS and LS packets finish many clock cycles after stp is
asserted. The Link must look for RX CMD bytes indicating
SE0-to-J transition to determine when the transmission has
completed on the USB bus.
6-9
N/A
N/A
HS SOF packets have a long EOP. The link must wait at
least 9 clocks or for an RX CMD indicating squelch
(LineState = 00b) before transmitting the next packet.
RX Start Delay
3-8
N/A
N/A
Number of clocks after first K of SYNC pattern is seen on
the USB bus to the simultaneous assertion of dir and nxt,
or an RX CMD indicating RxActive. Used for HS packets
only.
For FS and LS packets the Link must look for RX CMD
bytes indicating J-to-K transition.
RX End Delay
3-8
17-18
122-123
Number of clocks after EOP occurs on the USB bus to the
PHY de-asserting dir or indicating RxActive low in an RX
CMD byte.
HS EOP is measured when all 8 consecutive 1’s have
finished transmitting on the USB bus.
FS and LS EOP occurs when SE0 starts on the USB bus.
For FS and LS, the Link uses LineState and not RX End
Delay to time USB packets.
Definition
Table 9 – PHY pipeline delays
8
Same as UTMI’s LineState delay of 2-3 clocks, but with 1 extra clock cycle added to the maximum due to ULPI bus
turnaround during an RX CMD.
27
3.8.2.6.3
October 20, 2004
Link Decision Time
Table 10 shows the time allotted to the ULPI Link for the various packet sequences. When the Link transmits
the second packet, it must meet the inter-packet delay. When the Link is expecting a response to a
transmitted packet, it must time the inter-packet delay to detect a timeout. For back-to-back receive packets,
the Link must be capable of receiving them with the timing given.
Packet Sequence
HS Link
Delay
FS Link
Delay
LS Link
Delay
Definition
Transmit-Transmit
(host only)
15-24
7-189
77-247
Number of clocks a host link must wait before driving
the TX CMD for the second packet.
In HS, the link starts counting from the assertion of
stp for the first packet.
In FS, the link starts counting from the RX CMD
indicating LineState has transitioned from SE0-to-J
for the first packet. The timings given ensure interpacket delays of 2-6.5 bit times.
Receive-Transmit
1-14
7-189
77-247
Number of clocks the link must wait before driving the
TX CMD for the transmit packet.
In HS, the link starts counting from the end of the
receive packet (de-assertion of dir or an RX CMD
indicating RxActive is low).
In FS/LS, the link starts counting from the RX CMD
indicating LineState has transitioned from SE0-to-J
for the receive packet. The timings given ensure
inter-packet delays of 2-6.5 bit times.
Receive-Receive
(peripheral only)
1
1
1
Transmit-Receive
9210
80
718
Minimum number of clocks between consecutive
receive packets. The link must be capable of
receiving both packets.
Host or peripheral transmits a packet and will timeout
after this amount of clock cycles if a response is not
received7. Any subsequent transmission can occur
after this time.
Table 10 – Link decision times
9
Same as UTMI’s FS SIE Decision Time of 7-19 clocks, but with 1 clock cycle subtracted from the maximum due to the
ULPI PHY requiring a bus turnaround during the RX CMD.
10
The UTMI specification [Ref 3] Hi-Speed transmit to receive timing is incorrect and should be ignored.
28
3.8.2.6.4
October 20, 2004
Inter-packet Timing Diagrams
Figure 19 and Figure 20 illustrate the PHY pipeline delays and the Link decision time for the various packet
sequences.
USB Inter-packet Delay (88-192 HS bit times)
USB
data
eop
idle
sync
clk
data
DN-1
DN
TX CMD
D0
D1
dir
stp
nxt
TX End Delay
(2-5 clocks)
Link Decision Time
(15-24 clocks)
TX Start Delay
(1-2 clocks)
Figure 19 – HS transmit-to-transmit packet timing
USB Inter-packet Delay (8-192 HS bit times)
USB
data
eop
idle
sync
clk
data
DN-4 DN-3 DN-2 DN-1
DN
turn
around
TX CMD
D0
D1
dir
stp
nxt
RX End Delay
(3-8 clocks)
Link Decision Time (1-14 clocks)
TX Start Delay
(1-2 clocks)
Figure 20 – HS receive-to-transmit packet timing.
29
3.8.3
October 20, 2004
Register Operations
ULPI provides a set of registers in the PHY that are accessed by the Link to control PHY functionality. The
ULPI register set is detailed in chapter 4. Where possible, registers follow the input signals defined in the
UTMI+ specification [Ref 4]. The Link can read or write register bytes, set and clear register bits as needed
using the TX CMD byte of Table 6.
3.8.3.1
Immediate Register Read and Write
Immediate registers are accessed by first sending the TX CMD byte as either a RegWrite or a RegRead
command with the required register address.
For a register write, as shown in Figure 21, the Link sends a register write command and waits for nxt to
assert. In the cycle after nxt asserts, the Link sends the register write data and waits for nxt to assert again.
When nxt asserts the second time, the Link asserts stp in the following cycle to complete the operation. The
PHY must detect stp assertion before it can accept another transmit command. If the PHY aborts the
RegWrite by asserting dir, the Link must retry the RegWrite when the bus is idle.
For a register read, as shown in Figure 22, the Link sends a register read command and waits for nxt to
assert. In the cycle after nxt asserts, the PHY asserts dir to gain control of the data bus. In the cycle after
dir asserts, the PHY must return the register read data. The PHY does not assert nxt when dir is asserted
during the register read operation, even during the cycle that register read data is being returned. This
allows a USB receive to always over-ride the register read during any cycle, and is explained in 3.8.3.2. If
the PHY aborts the RegRead by asserting dir earlier than shown in Figure 22, the Link must retry the
RegRead when the bus is idle.
clock
data[7:0]
TX CMD
(RegWrite)
Data
dir
stp
nxt
Figure 21 – Register write
30
October 20, 2004
clock
TX CMD
(RegRead)
data[7:0]
turn
around
Data
turn
around
dir
stp
nxt
Figure 22 – Register read
3.8.3.2
Immediate Register Read and Write Aborted by USB Receive
A register read is the only instance where ULPI does not use nxt to throttle data. The nxt signal is asserted
only during USB receive so that the Link can always distinguish a USB receive from other data transfers.
Figure 23 shows a register read or write being aborted by a USB receive during the initial Transmit
Command byte. Figure 24 shows a register read being aborted by a USB receive in the same cycle that
register read data was to be returned to the Link. In both cases, the PHY asserts both dir and nxt to indicate
RxActive.
Register read and write operations are also aborted by the PHY sending an RX CMD, except during the
cycle that register read data is being returned to the Link.
ULPI Signals
RegRead or RegWrite
USB Receive
clock
data[7:0]
TX CMD
(Reg)
turn
around
RX CMD
PID
D1
D2
D3
dir
stp
nxt
RxActive
Figure 23 – Register read or write aborted by USB receive during TX CMD byte
31
October 20, 2004
ULPI Signals
RegRead or RegWrite
USB Receive
clock
data[7:0]
TX CMD
(Reg)
turn
around
RX CMD
PID
D1
D2
dir
stp
nxt
RxActive
Figure 24 – Register read turnaround cycle or Register write data cycle aborted by USB receive
3.8.3.3
Back-to-back Immediate Register Read/Write and USB Receive
Figure 25 shows a USB receive occurring in the same cycle that register read data is returned to the Link.
The PHY must first return the register read data, not an RX CMD byte indicating RxActive. The PHY
indicates RxActive in the next cycle, placing the USB Receive data back-to-back with the register read.
Figure 26 shows a USB receive occurring in the cycle immediately after a register read completes. The PHY
places the USB receive data back-to-back with the register read.
The Link must be able to accept back-to-back packets where dir does not de-assert between packets.
As shown in Figure 27, if dir asserts during the same cycle that stp is asserted at the end of a register write
operation, the PHY considers the register write to have completed successfully. The PHY does not de-assert
dir because of stp.
Figure 28 shows a USB receive starting in the cycle after the register read data is returned to the Link. Note
the two cycles of bus turnaround when dir de-asserts for a single cycle.
In all cases, the PHY asserts dir and nxt to indicate RxActive.
32
October 20, 2004
ULPI Signals
USB Receive
RegRead
clock
TX CMD
(RegRead)
data[7:0]
turn
around
Reg Data
RX CMD
(RxActive)
PID
D1
D2
dir
stp
nxt
RxActive
Figure 25 – USB receive in same cycle as register read data. USB receive is delayed.
ULPI Signals
USB Receive
RegRead
clock
TX CMD
(RegRead)
data[7:0]
turn
around
Reg Data
RX CMD
(RxActive)
PID
D1
D2
dir
stp
nxt
RxActive
Figure 26 – Register read followed immediately by a USB receive
33
October 20, 2004
ULPI Signals
RegWrite
USB Receive
clock
TX CMD
(RegWrite)
data[7:0]
Data
turn
around
RX CMD
PID
D1
D2
dir
stp
nxt
RxActive
Figure 27 – Register write followed immediately by a USB receive during stp assertion
ULPI Signals
USB Receive
RegRead
clock
TX CMD
(RegRead)
data[7:0]
turn
around
Reg Data
turn
around
turn
around
dir
stp
nxt
RxActive
Figure 28 – Register read followed by a USB receive
34
PID
D1
3.8.3.4
October 20, 2004
Extended Register Read and Write
Access to immediate register address 2Fh indicates an access to the extended register set. In this case, the
address is available in the next clock cycle.
For an extended register write, as shown in Figure 29, the Link sends a register write command with the
address set to 2Fh, and waits for nxt to assert. In the cycle after nxt asserts, the Link sends the extended
register address and waits for nxt to assert again. When nxt asserts the second time, the Link sends the
register write data and waits for nxt to assert again. When nxt asserts the third time, the Link asserts stp in
the following cycle to complete the operation. If the PHY aborts the RegWrite by asserting dir, the Link must
retry the RegWrite when the bus is idle.
For an extended register read, as shown in Figure 30, the Link sends a register read command with the
address set to 2Fh, and waits for nxt to assert. In the cycle after nxt asserts, the Link sends the extended
register address and waits for nxt to assert again. When nxt asserts the second time, the PHY asserts dir to
gain control of the data bus. In the cycle after dir asserts, the PHY returns the register read data. The PHY
does not assert nxt when dir is asserted during the register read operation, even during the cycle that
register read data is being returned. This allows a USB receive to over-ride the register read during any
cycle, and is explained in 3.8.3.5. If the PHY aborts the RegRead by asserting dir earlier than shown in
Figure 30, the Link must retry the RegRead when the bus is idle.
clock
data[7:0]
TX CMD
Extended
(Extended RegWrite) Address
Data
dir
stp
nxt
Figure 29 – Extended register write
clock
data[7:0]
TX CMD
Extended
(Extended RegRead) Address
turn
around
Data
turn
around
dir
stp
nxt
Figure 30 – Extended register read
35
3.8.3.5
October 20, 2004
Extended Register Read aborted by and back-to-back with USB Receive
An extended register read is identical to an immediate register read, except for the extended address byte
cycle. Therefore, Figure 23, Figure 24, Figure 26, and Figure 27 also apply to extended register reads.
There is one extra corner case and this is shown in Figure 31, an extended register read aborted by a USB
receive during the extended address cycle.
Extended register read and write operations are also aborted by the PHY sending an RX CMD, except
during the cycle that register read data is being returned to the Link.
Extended RegRead
USB Receive
clock
data[7:0]
TX CMD
(Extended RegRead)
turn
around
RX CMD
PID
D1
turn
around
dir
stp
nxt
Figure 31 – Extended register read aborted by USB receive during extended address cycle
36
3.8.4
October 20, 2004
Aborting ULPI Transfers
3.8.4.1
Link aborted by PHY
When the Link is transferring data on the ULPI bus, the PHY can abort the Link by asserting dir. ULPI does
not specify any conditions that will cause this to happen.
3.8.4.2
PHY aborted by Link
When the PHY has dir asserted in Synchronous Mode, the Link can abort the PHY by asserting stp, as
shown in Figure 32 and Figure 33. In the next cycle, the PHY must de-assert dir, and keep dir de-asserted,
until the Link transaction has completed. If the Link performs a register write or USB transmit as in Figure 32,
the PHY must wait for the stp pulse at the end of the sequence before re-asserting dir. If the Link performs a
register read, the PHY must return the register read data as in Figure 33, and is allowed to continue to
assert dir if it needs to communicate USB Receive data or an RX CMD.
The Link cannot abort the PHY in the same cycle that dir is asserted, and the PHY must ignore stp in the
same cycle that it first asserts dir.
If the Link asserts stp in the same cycle that dir is de-asserted, the PHY must still guarantee the Link
transaction.
When the PHY is aborted, the Link must drive a TX CMD immediately after the turnaround cycle. If the Link
does not immediately drive a TX CMD, the PHY is allowed to re-assert dir, as shown in Figure 34.
All ULPI PHY implementations must support being aborted by the Link asserting stp. While this feature can
be used at any time, it is provided primarily for the Link to shut down a babbling port by disabling the PHY.
The PHY cannot guarantee the validity of USB data during the current packet and the next packet if the Link
asserts stp during a USB receive packet.
Guaranteed Link transaction
clock
data[7:0]
DATA
DATA
turn
around
TX CMD
DATA
dir
stp
nxt
Figure 32 – PHY aborted by Link asserting stp. Link performs register write or USB transmit.
37
October 20, 2004
Guaranteed Link transaction
clock
data[7:0]
DATA
DATA
turn
around
TX CMD
(RegRead)
turn
around
DATA
turn
around
dir
stp
nxt
Figure 33 – PHY aborted by Link asserting stp. Link performs register read.
No TX CMD. PHY can assert dir.
clock
data[7:0]
DATA
DATA
turn
around
dir
stp
nxt
Figure 34 – Link aborts PHY. Link fails to drive a TX CMD. PHY re-asserts dir.
38
3.8.5
October 20, 2004
USB Operations
The following sections describe how the Link and PHY must communicate on the ULPI bus to perform
specific USB operational sequences. The diagrams are compressed horizontally on the time axis and not to
scale.
3.8.5.1
Hi-Speed Detection Handshake (Chirp)
Hi-Speed Detection Handshake, or Chirp, is shown in Figure 35. Note that Figure 35 timing is not to scale,
and not all RX CMD updates are shown. Bus turnaround cycles are also not shown, and must occur for one
cycle after every assertion and de-assertion of dir. The following sequence of events must be followed.
1. FS/LS Detect – The host detects a peripheral attachment as low speed if D- is high and as full
speed if D+ is high. If a host detects a low speed peripheral, it does not follow the remainder of this
protocol.
2. Host Drives – If a host detects a full speed peripheral, it resets the peripheral by writing to the
Function Control register and setting XcvrSelect = 00b (HS) and TermSelect = 0b which drives
SE0 on the bus (D+ and D- connected to ground via 45Ω). The host also sets OpMode = 10b for
correct chirp transmit and receive11. The start of SE0 is labelled T0. The peripheral PHY asserts dir
and informs the Link of the LineState change using an RX CMD.
3. Peripheral Responds – After detecting SE0 for no less than 2.5us, if the peripheral is Hi-Speed
capable, the peripheral Link sets XcvrSelect to 00b (HS) and OpMode to 10b (chirp), and follows
this immediately with a TX CMD (NOPID), transmitting a chirp K for no less than 1ms. and the chirp
K must end it no more than 7ms after reset time T0. If the peripheral is in Low Power Mode, it must
wake up its clock within 5.6ms, leaving 200us for the Link to start transmitting the chirp K, and 1.2ms
for the chirp K to complete (worst case with 10% slow clock).
4. Host Responds – If the host does not detect the peripheral chirp, it must continue the assertion of
SE0 until the end of reset. If the host detects the peripheral chirp K for no less than 2.5us, then no
more than 100us after the bus leaves the chirp K state, the host sends a TX CMD (NOPID) with an
alternating sequence of chirp K’s and J’s. Each individual chirp K or J must last no less than 40us
and no longer than 60us.
5. HS Idle – The peripheral must detect a minimum of chirp K-J-K-J-K-J. Each individual chirp K and J
must be detected for at least 2.5us. After seeing that minimum sequence, the peripheral Link sets
TermSelect = 0b and OpMode = 00b. The peripheral is now in Hi-Speed mode and sees !squelch
(01b) on LineState. When the peripheral sees squelch (10b) on LineState, it knows the host has
completed chirp and waits for Hi-Speed USB traffic to begin. After transmitting the chirp sequence,
the host changes OpMode to 00b and begins sending USB packets.
11
Receiving chirp signalling causes LineState to be encoded differently, and takes into account the Hi-Speed differential
receiver output so as not to see false bus activity.
39
ULPI Host
FS/LS detect Host drives
T0
TX CMD S
E
data[7:0]
RegWr 0
October 20, 2004
Device Responds
Host Responds
TXCMD
NOPID
0
0
K
K
J
...
K
J
HS Idle
TX CMD
RegWr
dir
stp
nxt
XcvrSelect
01(FS)
00(HS)
TermSelect
OpMode
LineState
00(normal)
10(chirp)
J
(01b)
SE0
(00b)
00(normal)
Peripheral chirp K
(10b)
Host Chirp K/J
(10b/01b)
squelch
(00b)
squelch
(00b)
ULPI Peripheral
RX CMD’s
S
E
0
data[7:0]
TX CMD
RegWr
TXCMD
NOPID
K
K
...
K
0
0
K
J
K
J
K
J
TX CMD
RegWr
0
0
dir
stp
nxt
XcvrSelect
01(FS)
00(HS)
TermSelect
OpMode
LineState
00(normal)
J
(01b)
10(chirp)
SE0
(00b)
Peripheral chirp K
(10b)
squelch
(00b)
00(normal)
Host Chirp K/J
(10b/01b)
!squelch
(01b)
squelch
(00b)
USB Signals
D+
D-
Figure 35 – Hi-Speed Detection Handshake (Chirp) sequence (timing not to scale)
40
3.8.5.2
October 20, 2004
Preamble
USB defines preamble packets as headers to low speed packets that must travel over a full speed bus,
between host and hub. To enter preamble mode, the Link sets XcvrSelect = 11b in the Function Control
register. When in preamble mode, the PHY operates identically to full speed mode, and sends all data with
full speed rise and fall times. Whenever the Link transmits a USB packet in preamble mode, the PHY must
automatically send a preamble header at full speed bitrate before sending the Link packet at low speed
bitrate. The PHY must ensure a minimum gap of 4 full speed bit times between the last bit of the full speed
PRE PID and the first bit of the low speed packet SYNC. The PHY must drive a J for at least 1 FS bit time
after sending the PRE PID, after which the pull-up resistor can hold the J state on the bus.
In preamble mode, the PHY can also receive low speed packets from the full speed bus.
ULPI Signals
clock
data[7:0]
TX CMD
(low speed packet PID)
D0
D1
PID
D0
D1
dir
stp
nxt
TxValid
TxReady
TxData[7:0]
USB Signals
D+/D-
FS
SYNC
FS
PRE PID
Idle (min
4 FS bits)
LS
SYNC
LS
PID
LS
D0
LS
D1
Figure 36 – Preamble sequence (D+/D- timing not to scale)
41
3.8.5.3
October 20, 2004
USB Suspend and Resume
This section deals with suspend and resume initiated by a host or hub.
3.8.5.3.1
Low Speed Suspend and Resume
Figure 37 illustrates how a host or hub enters Low Speed suspend and then initiates resume signalling to
wake up the downstream Low Speed peripheral. Note that Figure 37 timing is not to scale, and does not
show all RX CMD Linestate updates. Bus turnaround cycles are also not shown, and must occur for one
cycle after every assertion and de-assertion of dir. The following text describes the sequence of events.
1. LS Traffic – Initially, the host and peripheral are sending low speed traffic over the USB bus
(XcvrSelect set to 10b). The host has its 15kΩ pull-downs enabled (DpPulldown and DmPulldown
set to 1b) and the 45Ω terminations disabled (TermSelect set to 1b). The peripheral has the 1.5kΩ
pull-up connected to D- (TermSelect set to 1b).
2. LS Suspend – When the peripheral sees no bus activity for 3ms, it enters the suspend state. The
peripheral Link places the PHY into Low Power Mode by setting the SuspendM bit as described in
3.9, causing the PHY to draw only suspend current. The host may or may not be powered down.
3. Resume K – When the host wants to wake up the peripheral, it sets OpMode to 10b and transmits a
LS K for at least 20ms. The peripheral Link sees the Resume K (01b) on LineState, and asserts stp
to wake up the PHY as described in 3.9.
4. EOP – The host PHY automatically appends a LS EOP (2 bits LS SE0 followed by 1 bit LS J) when
stp is asserted. The host PHY knows to add the LS EOP because DpPulldown and DmPulldown
are set to 1b for a host. After the LS EOP has completed, the host Link sets OpMode to 00b for
normal LS operation. The peripheral Link sees the LS EOP and also resumes normal LS operation.
42
October 20, 2004
ULPI LS Host (XcvrSelect = 10b, DpPulldown = 1b, DmPulldown = 1b, TermSelect = 1b)
LS Traffic
LS Suspend
Resume K
TX CMD TX CMD
K
(RegWr) (NOPID)
data[7:0]
K
...
EOP
K
S
E
0
LS Traffic
J TX CMD
dir
stp
nxt
OpMode
00b
LS J/K
LineState (10/01)
10b
LS J (10b)
LS K (01b)
00b
SE0
(00b)
LS J (10b)
ULPI LS Peripheral (XcvrSelect = 10b, DpPulldown = 0b, TermSelect = 1b)
clk
data[7:0]
TX CMD
TX CMD
(RegWr)
LineState J
LineState K
TX CMD
(RegWr)
S
E
0
J
dir
stp
nxt
OpMode
00b
10b
00b
SuspendM
LS J/K
LineState (10/01)
LS J (10b)
LS K (01b)
SE0
(00b)
LS J (10b)
USB Signals
dp
dm
Figure 37 – LS Suspend and Resume (timing not to scale)
43
3.8.5.3.2
October 20, 2004
Full Speed Suspend and Resume
Figure 38 illustrates how a host or hub enters Full Speed suspend and then initiates resume signalling to
wake up the downstream Full Speed peripheral. Note that Figure 38 timing is not to scale, and does not
show all RX CMD Linestate updates. Bus turnaround cycles are also not shown, and must occur for one
cycle after every assertion and de-assertion of dir. The following text describes the sequence of events.
1. FS Traffic – Initially, the host and peripheral are sending full speed traffic over the USB bus
set to 1b) and the 45Ω terminations disabled (TermSelect set to 1b). The peripheral has the 1.5kΩ
pull-up connected to D+ (TermSelect set to 1b).
2. FS Suspend – When the peripheral sees no bus activity for 3ms, it enters the suspend state. The
peripheral Link places the PHY into Low Power Mode by setting the SuspendM bit as described in
3.9, causing the PHY to draw only suspend current. The host may or may not be powered down.
FS K for at least 20ms. The peripheral Link sees the Resume K (10b) on LineState, and asserts stp
4. EOP – The host PHY automatically appends a LS EOP (2 bits LS SE0 followed by 1 bit FS J) when
stp is asserted. The host PHY knows to add the LS EOP because DpPulldown and DmPulldown
are set to 1b for a host. After the LS EOP has completed, the host Link sets OpMode to 00b for
normal FS operation. The peripheral Link sees the LS EOP and also resumes normal FS operation.
ULPI FS Host (XcvrSelect=01b, DpPulldown=1b, DmPulldown=1b, TermSelect=1b)
FS Traffic
FS Suspend
Resume K
TX CMD TX CMD
K
(RegWr) (NOPID)
data[7:0]
K
...
EOP
FS Traffic
K
TX CMD
dir
stp
nxt
OpMode
00b
FS J/K
LineState (01/10)
10b
FS J (01b)
FS K (10b)
00b
SE0
(00b)
FS J (01b)
ULPI FS Peripheral (XcvrSelect=01b, DpPulldown=0b, TermSelect=1b)
clk
data[7:0]
TX CMD
TX CMD
(RegWr)
LineState J
LineState K
TX CMD
(RegWr)
S
E
0
J
dir
stp
nxt
OpMode
00b
10b
00b
SuspendM
FS J/K
LineState (01/10)
FS J (01b)
FS K (10b)
SE0
(00b)
USB Signals
dp
dm
Figure 38 – FS Suspend and Resume (timing not to scale)
44
FS J (01b)
3.8.5.3.3
October 20, 2004
Hi-Speed Suspend and Resume
Figure 39 illustrates how a Hi-Speed host or hub enters Full Speed suspend and then initiates resume
signalling to wake up the downstream Hi-Speed peripheral. Note that Figure 39 timing is not to scale, and
does not show all RX CMD Linestate updates. Bus turnaround cycles are also not shown, and must occur
for one cycle after every assertion and de-assertion of dir. The following text describes the sequence of
events.
1. HS Traffic – Initially, the host and peripheral are sending Hi-Speed traffic over the USB bus
set to 1b) and the 45Ω terminations enabled (TermSelect set to 0b). The peripheral has its 45Ω
terminations enabled (TermSelect set to 0b).
2. FS Suspend – When the peripheral sees no bus activity for 3ms, it enters the suspend state. The
peripheral Link places the PHY into Full Speed mode (XcvrSelect set to 01b), removes the 45Ω
terminations and enables the 1.5kΩ pull-up on D+ (TermSelect set to 1b). The peripheral Link then
places the PHY into Low Power Mode by setting SuspendM as described in 3.9, causing the PHY to
draw only suspend current. The host also changes to Full Speed (XcvrSelect set to 01b), removes
the 45Ω terminations (TermSelect set to 1b), and then may or may not be powered down.
FS K for at least 20ms. The peripheral Link sees the Resume K (10b) on LineState, and asserts stp
4. HS Traffic – The host Link sets Hi-Speed (XcvrSelect set to 00b), and enables its 45Ω terminations
(TermSelect set to 0b). The peripheral Link sees SE0 on the USB bus and also sets Hi-Speed
(XcvrSelect set to 00b), and enables its 45Ω terminations (TermSelect set to 0b). The host Link
sets OpMode to 00b for normal HS operation.
45
ULPI HS Host
October 20, 2004
(DpPulldown=1b, DmPulldown=1b)
HS Traffic
FS Suspend
TX CMD
(RegWr)
data[7:0]
Resume K
TX CMD TX CMD
K
(RegWr) (NOPID)
K
...
HS Traffic
K
TX CMD
(RegWr)
TX CMD
dir
stp
nxt
XcvrSelect
00b
00b
01b
TermSelect
OpMode
00b
squelch
LineState !squelch
(01b)
(00b)
00b
10b
FS J (01b)
FS K (10b)
!squelch
(01b)
squelch (00b)
ULPI FS Peripheral (DpPulldown=0b)
clk
data[7:0]
TX CMD
(RegWr)
TX CMD
LineState J
LineState K
TX CMD
(RegWr)
S
E
0
TX CMD
(RegWr)
dir
stp
nxt
XcvrSelect
00b
00b
01b
TermSelect
OpMode
00b
10b
00b
SuspendM
squelch
LineState !squelch
(00b)
(01b)
FS J (01b)
FS K (10b)
squelch (00b)
USB Signals
dp
dm
Figure 39 – HS Suspend and Resume (timing not to scale)
46
!squelch
(01b)
3.8.5.4
October 20, 2004
Remote Wake-up
This section deals with a peripheral initiating a remote wake-up (resume). When placed into USB suspend,
the Link remembers what speed it was originally operating in. Depending on the original speed, the Link
follows one of the protocols detailed below. Note that in the following figures, timing is not to scale, and not
all RX CMD Linestate updates are shown. Bus turnaround cycles are also not shown, and must occur for
one cycle after every assertion and de-assertion of dir.
3.8.5.4.1
Low Speed Remote Wake-up
ULPI Host
TxCmd
RegWr
data[7:0] LineState
TxCmd
NOPID
TxCmd
RegWr
00h
dir
stp
nxt
10b
XcvrSelect
TermSelect
10b
OpMode
00b
ULPI Peripheral
data[7:0] LineState
TxCmd
RegWr
TxCmd
NOPID
00h
RxCmd
RxCmd
RxCmd
TxCmd
RegWr
dir
stp
nxt
10b
XcvrSelect
TermSelect
00b
10b
OpMode
USB Signals
D+
D-
T1
A
B
C
D
E
F
G
H
J
Figure 40 – Low Speed Remote Wake-Up from Low Power Mode (timing not to scale)
A)
B)
C)
D)
E)
F)
G)
H)
J)
Both Host and Peripheral start out in Low Power Mode.
The Peripheral begins Remote Wake-Up by re-enabling its clock and setting its SuspendM
bit.
The Peripheral begins driving K on the bus to signal Resume. Note that the peripheral Link
should assume that LineState is K (01b) while transmitting.
The Host recognizes the resume, re-enables its clock and sets its SuspendM bit.
The Host takes over driving the resume within 1ms of detecting the remote wake-up12.
The Peripheral stops driving resume.
The Peripheral sees the Host continuing to drive the resume.
The Host stops driving Resume and the PHY adds the LS EOP to the end of Low Speed
Resume. The Peripheral recognizes the LS EOP as the end of Resume. (T1 is the LS EOP
interval. Refer to the UTMI+ specification [Ref 4] for more details).
Both Host and Peripheral revert to normal operation by writing OpMode to normal.
12
If the clock cannot be restarted in less than 1ms, the PHY must implement the AutoResume feature described in
3.8.5.4.4.
47
3.8.5.4.2
October 20, 2004
Full Speed Remote Wake-up
ULPI Host
TxCmd
RegWr
data[7:0] LineState
TxCmd
NOPID
TxCmd
RegWr
00h
dir
stp
nxt
01b
XcvrSelect
01b
TermSelect
10b
OpMode
00b
ULPI Peripheral
data[7:0] LineState
TxCmd
RegWr
TxCmd
NOPID
00h
RxCmd
RxCmd
RxCmd
TxCmd
RegWr
dir
stp
nxt
01b
01b
XcvrSelect
TermSelect
00b
10b
OpMode
USB Signals
D+
D-
T1
A
B
C
D
E
F
G
H
J
Figure 41 – Full Speed Remote Wake-Up from Low Power Mode (timing not to scale)
A)
B)
C)
D)
E)
F)
G)
H)
J)
48
The Peripheral begins Remote Wake-Up by re-enabling its clock and setting its SuspendM bit.
The Peripheral begins driving K on the bus to signal Resume. Note that the peripheral Link should
assume that LineState is K (10b) while transmitting.
The Host recognizes the resume, re-enables its clock and sets its SuspendM bit.
The Host stops driving Resume and the PHY adds the LS EOP to the end of Full Speed Resume.
The Peripheral recognizes the LS EOP as the end of Resume. (T1 is the LS EOP interval. Refer
to the UTMI+ specification [Ref 4] for more details)
Both Host and Peripheral revert to normal operation by writing OpMode and XcvrSelect.
3.8.5.4.3
October 20, 2004
Hi-Speed Remote Wake-up
ULPI Host
TxCmd
RegWr
data[7:0] LineState
TxCmd
NOPID
TxCmd
RegWr
00h
dir
stp
nxt
01b
XcvrSel
00b
TermSel
10b
OpMode
00b
ULPI Peripheral
data[7:0] LineState
TxCmd
RegWr
TxCmd
NOPID
00h
TxCmd
RegWr
RxCmd
RxCmd
dir
stp
nxt
01b
XcvrSel
00b
TermSel
10b
OpMode
00b
USB Signals
D+
DT1
A
B
C
D
E
F
G
H
J
Figure 42 – Hi-Speed Remote Wake-Up from Low Power Mode (timing not to scale)
A)
B)
C)
D)
E)
F)
G)
H)
J)
The Peripheral begins Remote Wake-Up by re-enabling its clock and setting its SuspendM bit (1).
The Peripheral begins driving K on the bus to signal Resume. Note that the peripheral Link should
assume that LineState is K (10b) while transmitting.
The Host recognizes the resume, re-enables its clock and sets its SuspendM bit (2).
The Host stops driving Resume and the Bus returns to Hi-Speed Idle. The Peripheral recognizes
the Hi-Speed Idle as the end of Resume. (T1 is the LS EOP interval. Refer to the UTMI+
specification [Ref 4] for more details)
Both Host and Peripheral revert to normal operation by writing OpMode, XcvrSelect and
TermSelect.
49
3.8.5.4.4
October 20, 2004
AutoResume
When a USB host detects remote wake-up signaling (resume-K) from a downstream peripheral or hub, the
host must take over driving of the resume-K signaling within 1ms. This is described in detail in the USB
specification [Ref 1], sections 7.1.7.7 and 7.9.
If the PHY is in host mode, the clock is powered down, and the remote wake-up signaling is detected by the
PHY, the Link must wake up the clock and take over driving of the resume-K signaling. If the clock cannot be
restarted within 1ms, the PHY must provide an automatic resume feature. As shown in Figure 43, the PHY
must internally drive the resume-K until the clock is restored and it receives a TXCMD of the NOPID type.
When the clock is restored, the Link takes over driving the resume-K by sending a TXCMD of the NOPID
type. The PHY must ensure there are no glitches during the resume sequence when transitioning between
automatic resume and the resume-K driven by the link in the NOPID command. The PHY must also ensure
the SuspendM register bit is automatically set to 1b before exiting Low Power Mode. Implementation details
are left to the PHY vendor, however the PHY vendor must specify the clock wake-up time, TSTART_HOST, as
defined in Table 4.
If the clock can be restarted within 1ms, the PHY does not need to provide the automatic resume feature.
Figure 40, Figure 41, Figure 42 can be applied without modification.
The AutoResume bit in the Interface Control register controls the automatic resume feature.
ULPI Signals
Clock wakeup = TSTART_HOST
clock
data
turn
around
Low Power Mode
TX CMD
(NOPID)
K
K
K
K
dir
stp
nxt
SuspendM
USB Signals
D+ / D- idle-J
resume-K
Downstream peripheral
drives remote wakeup
Host PHY automatically takes over driving resume-K
Figure 43 – Automatic resume signalling (timing not to scale)
50
Link drives resume-K.
PHY stops AutoResume
3.8.5.5
October 20, 2004
Peripheral Connect and Disconnect Detection
The HostDisconnect bit in the USB Interrupt Status register indicates when a peripheral is connected or
disconnected, and is valid only when the PHY is used as a host (DpPulldown and DmPulldown both set to
1b). When used as a host PHY, a change in an unmasked HostDisconnect causes the PHY to generate an
interrupt event notification as described in section 3.6.
When used as a peripheral (DpPulldown set to 0b), the PHY must never generate an interrupt event
notification indicating a Hostdisconnect event.
The reader is referred to the UTMI+ specification [Ref 4] for a discussion on how to generate the
HostDisconnect signal.
3.8.5.6
No SYNC and EOP Generation (OpMode 11b) (Optional)
This mode affects how packets are transmitted, and must be used for Hi-Speed only. When OpMode is set
to 11b, the PHY will not automatically add the SYNC and EOP patterns when transmitting a packet. The
PHY must still NRZI encode the data and perform bit-stuffing. When the Link wants to transmit a USB
packet, it must send a TX CMD of the NOPID type. After the NOPID command, the Link sends a 4-byte
SYNC pattern on the ULPI bus (00h, 00h, 00h, 80h), followed by the PID, data payload, and finally a 1-byte
EOP (FEh), as shown in Figure 44. The TxBitstuffEnable signal of UTMI+ is not supported. The PHY
automatically enables bit-stuffing when a packet is started, and disables bit-stuffing when stp is asserted.
The Link asserts stp in the same cycle it drives the EOP byte. If data is set to 00h when stp is asserted, the
PHY will not transmit any EOP on the USB bus. The PHY must detect if the PID byte is A5h (SOF packet)
and automatically send a long EOP when stp is asserted. For transmitting chirp and resume signalling, the
Link must set OpMode to 10b.
Sending a TX CMD of the PID type when OpMode is set to 11b will result in undefined behaviour. Receiving
RX CMD and USB receive packets when OpMode is 11b operates identically to OpMode 00b.
ULPI signals
clk
data
TX CMD
00h
00h 00h 08h PID
D1
D2
D3
...
...
DN-1
DN
FEh
dir
stp
nxt
UTMI+ equivalent signals
TxValid
TxReady
TxBitstuffEnable
USB bus
D+D-
idle
sync
pid
data payload
eop
idle
Figure 44 – USB packet transmit when OpMode is set to 11b.
51
3.8.6
October 20, 2004
Vbus Power Control (internal and external)
The link turns on Vbus by setting the DrvVbus bit in the OTG Control register. If the Vbus supply is external
to the PHY, the link sets DrvVbus and the optional DrvVbusExternal bit in the OTG Control register. The
VBUS control settings are detailed in Table 11.
DrvVbus
0
1
1
DrvExternalVbus
X
0
1
Power Source used
Internal and external VBUS power sources disabled.
Internal VBUS charge pump enabled.
External 5V VBUS supply enabled.
Table 11 – OTG Control Register power control bits
3.8.7
3.8.7.1
OTG Operations
Session Request Protocol (SRP)
ULPI provides full SRP support. The Link uses the ChrgVbus and DischrgVbus bits in the OTG Control
register to begin and end a session.
3.8.7.2
Host Negotiation Protocol (HNP) (Optional)
ULPI does not define HNP support. It is assumed that HNP is implemented in Link hardware and/or in
software. This does not preclude PHY implementers from adding HNP support to any ULPI PHY so long as it
does not interfere with or violate the ULPI protocol defined in this specification.
3.8.7.3
VBUS Comparator Thresholds
While the OTG specification [Ref 2] provides for separate A-device and B-device session valid comparators,
the A-device session valid comparator with a 0.8V to 2.0V threshold (VA_SESS_VLD) can also be used for the
B-device session valid comparator, which requires a 0.8V to 4.0V threshold (VB_SESS_VLD), removing the
need for a separate B-device comparator. Implementations with separate A-device and B-device session
valid comparators can map into the single session valid definition (VSESS_VLD). ULPI Vbus comparator
thresholds are shown in Table 12.
The purpose of the VA_VBUS_VLD threshold is to allow the A-device to determine whether or not it is able to
output a valid voltage on VBUS. Thus, the upper limit on the VA_VBUS_VLD threshold is not specified by ULPI.
However, the upper limit on this threshold is generally dependent on the characteristics of the A-device
power supply.
Thus, if the A-device power supply operates by driving VBUS to a reference of VA_VBUS_REF, and the output
voltage does not drop below x% when the B-devices on its Targeted Peripheral List are not drawing too
much current, then the threshold voltage would be:
4.4V < VA_VBUS_VLD ≤ (x / 100) * VA_VBUS_REF
where x is determined by the power supply designer.
Threshold Name
Threshold Range
B-device session end
0.2 ≤ VSESS_END < 0.8
A/B-device session valid
0.8 ≤ VSESS_VLD < 2.0
A-device Vbus Valid
4.4 ≤ VA_VBUS_VLD
Table 12 – Vbus comparator thresholds
52
October 20, 2004
If the VBUS power supply is external to the PHY, and the external supply provides a signal indicating when
VBUS is valid, it is recommended that this signal be an input to the PHY on an optional pin
ExternalVbusIndicator, and that the state of that pin be reflected to the Link via the VA_VBUS_VLD ≤ VBUS
indication in the RX CMD byte. The optional UseExternalVbusIndicator bit in the OTG Control register
selects between the internal and external VbusValid indicators.
To support industry standard USB power control devices, the PHY may optionally support two additional bits
in the Interface Control register, IndicatorPassThru and IndicatorComplement. These two bits allow the
optional ExternalVbusIndicator pin to interoperate with either a power valid signal or an over-current fault
output from the power control device, and to adapt to either active high or active low signals from the power
control device. When a power fault signal is provided on the ExternalVbusIndicator pin, the PHY must use
a logical combination of the output from the internal VbusValid comparator and the external power fault
signal to generate the VA_VBUS_VLD ≤ VBUS indication. Table 13 defines the use of the
UseExternalVbusIndicator, IndicatorPassThru and IndicatorComplement register bits to control the use
of the ExternalVbusIndicator input pin and the internal VbusValid comparator output to generate the
VA_VBUS_VLD ≤ VBUS indication in the RX CMD byte. Table 13 also indicates typical applications of each
setting. Figure 45 provides a graphical representation of the logical combination of the internal and external
VbusValid sources, and how the control register bits effect the VA_VBUS_VLD ≤ VBUS indication in the RX
CMD byte. The UseExternalVbusIndicator, IndicatorPassThru and IndicatorComplement control
register bits are individually optional. The PHY may implement any combination of the optional control bits,
however, if the control bits are implemented they must provide the function defined in Table 13. If any of the
control bits are not implemented it is the responsibility of the PHY to define how the optional
ExternalVbusIndicator pin effects the state of the VA_VBUS_VLD ≤ VBUS indication in the RX CMD byte.
RxCmd VBUS Valid source
Typical
Application
UseExternal
VbusIndicator
Indicator
PassThru
Indicator
Complement
OTG Device
0
don’t care
don’t care
1
1
0
External active high VA_VBUS_VLD signal.
1
1
1
External active low VA_VBUS_VLD_N
signal.
1
0
1
External active high power fault signal
qualified with internal VA_VBUS_VLD
comparator.
1
0
0
External active low power fault signal
qualified with internal VA_VBUS_VLD
comparator.
1
1
0
External active high power fault signal.
1
1
1
External active low power fault signal.
0
don’t care
don’t care
Standard
Host
Standard
Peripheral
Internal VA_VBUS_VLD comparator.
Internal VA_VBUS_VLD comparator.13
Table 13 – RX CMD VbusValid over-current conditions
13
A standard peripheral should not use Vbus Valid to begin operation. The internal VbusValid may not indicate Vbus is
valid on the 5th hub tier, which is allowed to be as low as 4.375V. Therefore the peripheral should use Session Valid.
53
Vbus
+
-
October 20, 2004
Internal VbusValid
(0,X)
RX CMD VbusValid
(1,0)
ExternalVBusIndicator
(1,1)
Complement Output
IndicatorComplement
(UseExternalVbusIndicator, IndicatorPassThru)
Figure 45 – RX CMD VA_VBUS_VLD ≤ Vbus indication source
Depending on the application, the link should enable or disable the appropriate VBUS interrupts. Example
settings for typical applications are given in Table 14.
Application
VbusValid14
SessValid
Standard Host
Yes
No
No
Standard Peripheral
No
Yes
No
OTG A-Device
Yes
Yes
No
OTG B-Device
No
Yes
Yes
SessEnd
Table 14 – Vbus indicators in the RX CMD required for typical applications
14
The VbusValid indicator in the RXCMD comes from either the internal VbusValid comparator, or the external Vbus
indicator input.
54
3.9
October 20, 2004
Low Power Mode
The Link can optionally place the PHY into Low Power Mode when the USB bus is suspended. The PHY can
power down all circuitry except the interface pins and full speed receiver. The bus resistors must also be
powered if VBUS is present. Any function must be powered if its corresponding register bit is set, including
interrupt sources and the charge pump. If the PLL is powered down, the clock must be stopped without
glitches.
3.9.1
Data Line Definition For Low Power Mode
When in Low Power Mode, the PHY drives data(3:0) with the signals listed in Table 15. When in Low Power
Mode, LineState must be driven combinatorially from the FS receiver. The int pin is asserted whenever any
unmasked interrupt occurs. The PHY must latch interrupt events directly from analog circuitry because clock
is powered down. The Link ignores the data(7:4) signals for 8-bit data bus configurations. These rules must
be followed for both input clock and output clock modes.
Signal
Maps to
Direction
Description
linestate(0)
data(0)
OUT
Combinatorial LineState(0) driven directly by FS analog receiver.
linestate(1)
data(1)
OUT
Combinatorial LineState(1) driven directly by FS analog receiver.
reserved
data(2)
OUT
Reserved. The PHY must drive this pin to low.
int
data(3)
OUT
Active high interrupt indication. Must be asserted whenever any
unmasked interrupt occurs.
Table 15 – Interface signal mapping during Low Power Mode
3.9.2
Entering Low Power Mode
The Link sets SuspendM in the Function Control register to 0b to place the PHY into Low Power Mode.
The Link or PHY clock may be stopped a minimum of five cycles after the PHY accepts the register write
data, as shown in Figure 46. While in Low Power Mode, the PHY asserts dir, and holds nxt low. There is
one cycle of data bus turnaround provided after the assertion of dir, during which the value on data is not
valid. The PHY starts driving the signals of Table 15 immediately after the turnaround cycle.
clock
(input/output)
data[7:0]
TX CMD
(RegWr)
Data
turn
around
Low Power Mode signals
dir
stp
nxt
SuspendM
Figure 46 – Entering low power mode
55
3.9.3
October 20, 2004
Exiting Low Power Mode
As shown in Figure 47 and Figure 48, the Link signals the PHY to exit Low Power Mode by asynchronously
asserting stp. The PHY immediately starts to wake up its internal circuitry. When the PHY clock meets ULPI
timing requirements, the PHY de-asserts dir. The PHY must ensure a minimum of 5 cycles of clock have
been driven prior to de-asserting dir. The PHY must also ensure that the SuspendM register is
automatically set to 1b prior to de-asserting dir. The Link de-asserts stp in the cycle following the deassertion of dir. There is one cycle of data bus turnaround provided after the de-assertion of dir, during
which the value on data is not valid. The PHY stops driving the signals of Table 15 immediately before the
turnaround cycle.
As shown in Figure 48, when the Link provides an input clock, the PHY must synchronize its internal clock
within TPREP. Note that TPREP is implementation dependent. Refer to Table 4 for more information on TPREP.
PHY output clock
data[7:0]
turn
around
Synchronous
Mode signals
dir
stp
nxt
SuspendM
Figure 47 – Exiting low power mode when PHY provides output clock
TPREP
Link input clock
Internally synchronized PHY clock
data[7:0]
turn
around
dir
stp
nxt
SuspendM
Figure 48 – Exiting low power mode when Link provides input clock
56
Synchronous
Mode signals
3.9.4
October 20, 2004
False Resume Rejection
Noise in the USB environment may cause momentary non-J-state conditions or glitches on the
asynchronous LineState outputs from the PHY during Low Power Mode. Glitches on LineState can
potentially cause momentary assertions of stp from the Link to the PHY. These should be considered as
false resume events and should be rejected by the PHY. The PHY may optionally reject glitches on stp prior
to re-starting the clock, as shown in Figure 49. The PHY must qualify the stp assertion that is used to exit
Low Power Mode by checking that stp is active on the clock edge that the PHY de-asserts dir. If stp is not
asserted during the cycle that dir is de-asserted, then the PHY must re-assert dir and return to Low Power
Mode without further action from the Link, as shown in Figure 50.
clock
data[7:0]
dir
stp
nxt
SuspendM
Figure 49 – PHY stays in Low Power Mode when stp de-asserts before clock starts.
clock
data[7:0]
dir
stp
nxt
SuspendM
Figure 50 – PHY re-enters Low Power Mode when stp de-asserts before dir de-asserts.
57
3.10
October 20, 2004
Full Speed / Low Speed Serial Mode (Optional)
Full Speed / Low Speed Serial Mode (FsLsSerialMode) gives the Link direct access to the FS/LS serial
analog transmitter and receiver. Two types of serial mode are defined in ULPI: 3-pin FsLsSerialMode, and
6-pin FsLsSerialMode. Both modes are optional. Unlike Low Power Mode, the FS/LS transmitters must be
powered. Any function must be powered if its corresponding register bit is set, including interrupt sources
and the charge pump.
3.10.1
Data Line Definition For FsLsSerialMode
The 6-pin serial mode provides a separate data line for each serial signal defined in UTMI+. The 3-pin serial
mode compresses the USB receive and transmit data onto bi-directional data lines and is provided so that 4bit data bus PHY implementations can support serial signalling. When in 6-pin serial mode, the PHY drives
data(7:0) with the signals listed in Table 16. When in 3-pin serial mode, the PHY drives data(3:0) with the
signals listed in Table 17.
In either mode, the active-low tx_enable_n signal of UTMI+ is converted to active high tx_enable for
transmission over the ULPI bus. This allows the default ULPI bus idle state to remain at 00h.
In both serial modes, an interrupt pin is provided. The int pin is asserted whenever an unmasked interrupt
event occurs.
Signal
Maps to
Direction
Description
tx_enable
data(0)
IN
Active high transmit enable.
tx_dat
data(1)
IN
Transmit differential data on D+/D-.
tx_se0
data(2)
IN
Transmit single-ended zero on D+/D-.
int
data(3)
OUT
rx_dp
data(4)
OUT
Single-ended receive data from D+.
rx_dm
data(5)
OUT
Single-ended receive data from D-.
rx_rcv
data(6)
OUT
Differential receive data from D+/D-.
reserved
data(7)
OUT
Reserved. The PHY must drive this pin to low.
Table 16 – Serial Mode signal mapping for 6-pin FsLsSerialMode
Signal
Maps to
Direction
tx_enable
data(0)
IN
dat
data(1)
I/O
se0
data(2)
I/O
int
data(3)
OUT
Description
Active high transmit enable.
Transmit differential data on D+/D- when tx_enable is high.
Receive differential data from D+/D- when tx_enable is low.
Transmit single-ended zero on D+/D- when tx_enable is high.
Receive single-ended zero from D+/D- when tx_enable is low.
Table 17 – Serial Mode signal mapping for 3-pin FsLsSerialMode
58
3.10.2
October 20, 2004
Entering FsLsSerialMode
To enter 6-pin serial mode, the Link sets the 6-Pin FsLsSerialMode bit in the Interface Control register,
causing the data bus to switch to asynchronous operation and take on a new definition as shown in Table
16.
To enter 3-pin serial mode, the Link sets the 3-Pin FsLsSerialMode bit in the Interface Control register,
causing the data bus to switch to asynchronous operation and take on a new definition as shown in Table
17.
By default, the output clock is powered down to reduce power consumption in serial mode. Entering Serial
Mode and stopping the clock shown in Figure 51. The clock can be stopped a minimum of 5 clock cycles
after Serial Mode is entered. When the clock is not usable, the PHY must assert dir. There is one cycle of
data bus turnaround provided after the assertion of dir, during which the value on data is not valid. The PHY
starts driving the serial mode signals immediately after the turnaround cycle.
If the Link requires the clock to be running in Serial Mode, it can set the ClockSuspendM signal in the
Interface Control register before entering Serial Mode. Entering Serial Mode with the clock running is
shown in Figure 52.
clock
data[7:0]
TX CMD
(RegWr)
Data
turn
around
FsLsSerialMode signals
dir
stp
nxt
FsLsSerialMode
Figure 51 – Interface behaviour when entering Serial Mode and clock is powered down
clock
data[7:0]
TX CMD
(RegWr)
Data
turn
around
dir
stp
nxt
FsLsSerialMode
Figure 52 – Interface behaviour when entering Serial Mode and clock remains powered
59
3.10.3
October 20, 2004
Exiting FsLsSerialMode
When the Link detects int as high, it should exit FsLsSerialMode by asserting stp. When the ULPI interface
has returned to Synchronous Mode, the Link can read the USB Interrupt Latch register to determine the
source of the interrupt. Exiting FsLsSerialMode is identical to exiting Low Power Mode if the clock is not
running. Exiting FsLsSerialMode when the clock is not running is shown in Figure 53.
If the clock is running, the Link signals the PHY to exit FsLsSerialMode by asserting stp. The PHY will deassert dir 1 or more cycles after it detects stp asserted, as shown in Figure 54. The Link de-asserts stp in
the cycle following the de-assertion of dir. Like Low Power Mode, there is a single cycle of bus turnaround
on data in the cycle following the de-assertion of dir. During the turnaround cycle, the value on data is not
valid. The PHY stops driving the serial mode signals immediately before the turnaround cycle.
PHY output clock
data[7:0]
turn
around
Synchronous
Mode signals
dir
stp
nxt
FsLsSerialMode
Figure 53 – Interface behaviour when exiting Serial Mode and clock is not running
clock
data[7:0]
turn
around
Synchronous Mode signals
dir
One or more clocks
stp
nxt
FsLsSerialMode
Figure 54 – Interface behaviour when exiting Serial Mode and clock is running
60
3.11
October 20, 2004
Carkit Mode (Optional)
This mode is selected when the CarkitMode bit in the Interface Control register is set. It allows the link to
communicate through the PHY to a remote carkit using UART signalling. Refer to [Ref 6] for more
information on carkit. In cases of conflict between this specification and the Carkit specification, the Carkit
specification shall take precedence.
By default, the clock is powered down when the PHY enters Carkit Mode. Entering and exiting Carkit Mode
is identical to Serial Mode. If the Link requires the clock to be running in Carkit Mode, it can set the
ClockSuspendM signal in the Interface Control register before entering Carkit Mode.
The int pin is asserted whenever an unmasked interrupt event occurs. When the Link detects int as high, it
should wake-up the clock (if powered down) by asserting stp. If the clock is already running, the Link asserts
stp for 1 cycle to switch the interface to Synchronous Mode. When the PHY is in Synchronous Mode, the
Link can read the Carkit Interrupt Latch register to determine the source of the interrupt.
Signal
Maps to
Direction
txd
data(0)
IN
rxd
data(1)
OUT
reserved
data(2)
-
int
data(3)
OUT
Description
UART TXD signal that is routed to D- pin.
UART RXD signal that is routed from D+ pin.
Reserved.
Active high interrupt indication. Must be asserted whenever
any unmasked interrupt occurs.
Table 18 – Carkit signal mapping
61
3.12
October 20, 2004
Safeguarding PHY Input Signals
For reasons including but not limited to hardware reset or slow power up, the link may not be able to
correctly drive the ULPI interface. In such cases, when the PHY has dir de-asserted, the link is unable to
drive data to the idle 00h state. The unknown values on the PHY data input signals could initiate unsolicited
USB activity, register writes, serial or carkit transmissions. For this reason, the PHY must protect its data
inputs at all times.
To safeguard against false commands on its data inputs, the PHY must incorporate a weak pull-up resistor
on stp. Any time stp is unexpectedly high, the PHY assumes the link is unable to drive the interface and
must enter a holding state. While in the holding state the PHY must not interpret commands on data, and
must not assert dir unless its internal clocks de-stabilize. The link is also allowed to drive stp high at any
time, forcing the PHY to stop interpreting commands on data. When the PHY is in the holding state, it can
optionally enable weak pull-down resistors on data, preventing them from floating.
All RXCMD changes that occur while the PHY is in the holding state must be replaced with a single RX CMD
update that is sent when the PHY exits the holding state, when the ULPI bus is available. The RX CMD
update must always convey the current RXCMD values, not a previous or old value.
If the link can always drive stp and data to known values, it can disable the protection feature by setting the
Interface Protect Disable bit in the Interface Control register to 1b. This potentially reduces power
consumption.
When the clock is running, the link should drive stp high for at least one clock cycle before ceasing to drive
the ULPI interface, forcing the PHY into the holding state to protect its data inputs. The pull up in the PHY
will hold stp high in subsequent cycles. Figure 55 illustrates this scenario. Safe PHY operation cannot be
guaranteed for implementations where the link cannot drive stp high before ceasing to drive the ULPI
interface.
Link unable to meet ULPI protocol
Link ready
clock
data[7:0]
PHY ignores data
dir
stp
nxt
Pull-up protects PHY
Link drives stp high
minimum 1 cycle
Figure 55 – PHY interface protected when the clock is running
During power up or when the clock is not running, the PHY always asserts dir, protecting its data inputs. As
shown in Figure 56 and Figure 57, if stp is high when the PHY de-asserts dir, the PHY will immediately
enter the holding state and protect its data inputs. When the link drives stp low, the PHY immediately starts
processing its data inputs.
Further to Figure 57, if the PHY is in Low Power Mode when the link ceases driving the ULPI interface, the
pull up on stp will automatically wake up the PHY. If the link does not want the PHY to automatically wake
up, it must drive stp low.
62
PHY powered
clock
Z
data[7:0]
Z
dir
Z
stp
Z
nxt
Z
October 20, 2004
Clock stable
PHY drives data
turn
around
Link ready
PHY ignores data
turn
around
RX turn
around
CMD
Figure 56 – Power up sequence when PHY powers up before the link. Interface is protected.
Clock stable
Link ready
clock
data[7:0]
PHY drives data
turn
around
PHY ignores
data
turn
around
RX turn
around
CMD
dir
stp
nxt
Figure 57 – PHY automatically exits Low Power Mode with interface protected
If dir is high when the link resumes driving the ULPI interface, the link should assume the PHY is in Low
Power Mode and drive stp high to wake up the PHY, as shown in Figure 58. The link de-asserts stp in the
cycle after dir is de-asserted. The PHY begins processing its data inputs in the cycle when dir and stp are
both low. This also applies during power up.
63
Link powered
October 20, 2004
Clock stable
clock
data[7:0]
turn
around
PHY drives data
turn
around
RX
CMD
turn
around
dir
stp
Pull-up begins wakeup
Link continues wakeup
nxt
Figure 58 – Link resumes driving ULPI bus and asserts stp because clock is not running
As shown in Figure 59, the link is allowed to drive stp low during power up, when dir is high. The PHY
begins processing its data inputs after the turnaround cycle when dir is de-asserted.
PHY powered
clock
Z
data[7:0]
Z
dir
Z
stp
nxt
Clock stable
PHY drives data
turn
turn
around around
RX turn
around
CMD
Link drives 00h
Link drives stp low before dir is low
Z
Figure 59 – Power up sequence when link powers up before PHY (ULPI 1.0 compliant links)
64
4.
4.1
October 20, 2004
Registers
Register Map
As shown in Table 19, ULPI provides an immediate register set with a 6-bit address that forms part of the
Transmit Command Byte. An extended register set is also provided with an 8-bit address that requires an
extra clock cycle to complete. The immediate register set is mirrored into the lower end of the extended
address space. That is, reading or writing to extended address “00XXXXXX” will in fact operate on the
immediate register set. The PHY must support both immediate and extended register operations. The
register access legend of Table 20 applies.
65
October 20, 2004
Size
(bits)
Rd
Vendor ID Low
8
00h
-
-
-
Vendor ID High
8
01h
-
-
-
Product ID Low
8
02h
-
-
-
Product ID High
8
03h
-
-
-
Function Control
8
04-06h
04h
05h
06h
Interface Control
8
07-09h
07h
08h
09h
OTG Control
8
0A-0Ch
0Ah
0Bh
0Ch
USB Interrupt Enable Rising
8
0D-0Fh
0Dh
0Eh
0Fh
USB Interrupt Enable Falling
8
10-12h
10h
11h
12h
USB Interrupt Status
8
13h
-
-
-
USB Interrupt Latch
8
14h
-
-
-
Debug
8
15h
-
-
-
Scratch Register
8
16-18h
16h
17h
18h
Carkit Control (Optional)
8
19-1Bh
19h
1Ah
1Bh
Carkit Interrupt Delay (Optional)
8
1Ch
1Ch
Carkit Interrupt Enable (Optional)
8
1Dh-1Fh
1Dh
1Eh
1Fh
Carkit Interrupt Status (Optional)
8
20h
-
-
-
Carkit Interrupt Latch (Optional)
8
21h
-
-
-
Carkit Pulse Control (Optional)
8
22-24h
22h
23h
24h
Transmit Positive Width (Optional)
8
25h
25h
-
-
Transmit Negative Width (Optional)
8
26h
26h
-
-
Receive Polarity Recovery (Optional)
8
27h
27h
-
-
Reserved
8
Access Extended Register Set (see below)
8
-
-
Vendor-specific
8
Field name
Address (6 bits)
Wr
Set
Clr
Immediate Register Set
-
2Fh
30-3Fh
Address (8 bits)
Extended Register Set
Maps to Immediate Register Set above
8
00-3Fh
Reserved
8
40-7Fh
Vendor-Specific
8
80-FFh
Table 19 – Register map
66
28-2Eh
October 20, 2004
Access Code
Expanded Name
Meaning
rd
Read
Register can be read. Read-only if this is the only mode given.
wr
Write
Pattern on the data bus will be written over all bits of the register.
s
Set
Pattern on the data bus is OR’d with and written into the register.
c
Clear
Pattern on the data bus is a mask. If a bit in the mask is set, then
the corresponding register bit will be set to zero (cleared).
Table 20 – Register access legend
4.2
Immediate Register Set
4.2.1
Vendor ID and Product ID
Address: 00h-03h Read-only.
Register
Bits
Access
Address
Reset
Description
Vendor ID Low
7:0
rd
00h
Fixed
Lower byte of Vendor ID supplied by USB-IF.
Vendor ID High
7:0
rd
01h
Fixed
Upper byte of Vendor ID supplied by USB-IF.
Product ID Low
7:0
rd
02h
Fixed
Lower byte of Product ID supplied by Vendor.
Product ID High
7:0
rd
03h
Fixed
Upper byte of Product ID supplied by Vendor.
Table 21 – Vendor ID and Product ID register description
67
4.2.2
October 20, 2004
Function Control
Address: 04h-06h (Read), 04h (Write), 05h (Set), 06h (Clear).
Controls UTMI function settings of the PHY.
Field name
XcvrSelect
Bit
Access
Reset
1:0
rd/wr/s/c
01b
Description
Selects the required transceiver speed.
00b : Enable HS transceiver
01b : Enable FS transceiver
10b : Enable LS transceiver
11b : Enable FS transceiver for LS packets
(FS preamble is automatically pre-pended)
TermSelect
OpMode
2
rd/wr/s/c
0b
Controls the internal 1.5kΩ pull-up resistor and 45Ω HS
terminations. Control over bus resistors changes depending
on XcvrSelect, OpMode, DpPulldown and DmPulldown,
as shown in Table 41. Since Low Speed peripherals never
support Full Speed or Hi-Speed, providing the 1.5kΩ on Dfor low speed is optional.
4:3
rd/wr/s/c
00b
Selects the required bit encoding style during transmit.
00b : Normal operation
01b : Non-driving
10b : Disable bit-stuff and NRZI encoding
11b :
Optional. Do not automatically add SYNC and EOP
when transmitting. Must be used only for HS packets.
Reset
5
rd/wr/s/c
0b
Active high transceiver reset. After the Link sets this bit, the
PHY must assert dir and reset the UTMI+ core. When the
reset is completed, the PHY de-asserts dir and
automatically clears this bit. After de-asserting dir, the PHY
must re-assert dir and send an RX CMD update to the Link.
The Link must wait for dir to de-assert before using the ULPI
bus. Does not reset the ULPI interface or ULPI register set.
SuspendM
6
rd/wr/s/c
1b
Active low PHY suspend. Put PHY into Low Power Mode.
The PHY can power down all blocks except the full speed
receiver, OTG comparators, and the ULPI interface pins.
The PHY must automatically set this bit to ‘1’ when Low
Power Mode is exited.
0b : Low Power Mode
1b : Powered
Reserved
7
rd/wr/s/c
0b
Reserved.
Table 22 – Function Control register
68
4.2.3
October 20, 2004
Interface Control
Enables alternative interfaces and PHY features. All bits in this register are optional features of the PHY.
Field name
6-pin
FsLsSerialMode
Bits
Access
Reset
0
rd/wr/s/c
0b
Description
Changes the ULPI interface to 6-pin Serial Mode. The PHY
must automatically clear this bit when serial mode is exited.
It is optional for any ULPI PHY to support this mode.
A PHY that has only 4 data pins can never support this
mode.
0b : FS/LS packets are sent using parallel interface.
1b : FS/LS packets are sent 6-pin using serial interface.
3-pin
FsLsSerialMode
1
rd/wr/s/c
0b
Changes the ULPI interface to 3-pin Serial Mode. The PHY
must automatically clear this bit when serial mode is exited.
0b : FS/LS packets are sent using parallel interface.
1b : FS/LS packets are sent using 4-pin serial interface.
CarkitMode
2
rd/wr/s/c
0b
Changes the ULPI interface to carkit interface. The PHY
must automatically clear this bit when carkit mode is exited.
Refer to [Ref 6] for more information on carkit.
0b : Disable serial carkit mode.
1b : Enable serial carkit mode.
ClockSuspendM
3
rd/wr/s/c
0b
Active low clock suspend. Valid only in Serial Mode and
Carkit Mode. Powers down the internal clock circuitry
only15. Valid only when SuspendM = 1b. The PHY must
ignore ClockSuspend when SuspendM = 0b. By default,
the clock will not be powered in Serial and Carkit Modes.
0b : Clock will not be powered in Serial and Carkit Modes.
1b : Clock will be powered in Serial and Carkit Modes.
AutoResume
4
rd/wr/s/c
Xb
Enables the PHY to automatically transmit resume
signaling.
Any PHY that cannot wake up its clock in less than 1ms
must implement this feature and have it turned on by
default. The Link can disable this feature if needed.
Any PHY that can wake up its clock in less than 1ms can
optionally implement this feature and should have it turned
off by default.
Refer to USB specification 7.1.7.7 and 7.9 for more details.
Indicator
Complement
5
rd/wr/s/c
0b
Tells the PHY to invert the ExternalVbusIndicator input
signal, generating the Complement Output. Refer to 3.8.7.3
and Figure 45 for more details.
0b: PHY will not invert ExternalVbusIndicator signal
(default).
1b: PHY will invert ExternalVbusIndicator signal.
15
Useful for Link implementations that switch to serial or carkit mode(s), and do not require a clock source from the PHY.
69
Field name
Indicator
PassThru
Bits
Access
Reset
6
rd/wr/s/c
0b
October 20, 2004
Description
Controls whether the Complement Output is qualified with
the Internal VbusValid comparator before being used in the
Vbus State in the RX CMD. Refer to 3.8.7.3 and Figure 45
for more details.
0b: Complement Output signal is qualified with the Internal
VbusValid comparator.
1b: Complement Output signal is not qualified with the
Internal VbusValid comparator.
Interface Protect
Disable
7
rd/wr/s/c
0b
Controls circuitry built into the PHY for protecting the ULPI
interface when the link tri-states stp and data. Any pull-ups
or pull-downs employed by this feature can be disabled.
This bit is not intended to affect the operation of the holding
state. Refer to section 3.12 for more details.
0b : Enables the interface protect circuit (default).
1b : Disables the interface protect circuit.
Table 23 – Interface Control register
70
4.2.4
October 20, 2004
OTG Control
Address: 0Ah-0Ch (Read), 0Ah (Write), 0Bh (Set), 0Ch (Clear). Controls UTMI+ OTG functions of the PHY.
Field name
Bits
Access
Reset
Description
IdPullup
0
rd/wr/s/c
0b
Connects a pull-up to the ID line and enables sampling16 of the
signal level.
0b : Disable sampling of ID line.
1b : Enable sampling of ID line.
DpPulldown
1
rd/wr/s/c
1b
Enables the 15k Ohm pull-down resistor on D+.
0b : Pull-down resistor not connected to D+.
1b : Pull-down resistor connected to D+.
DmPulldown
2
rd/wr/s/c
1b
Enables the 15k Ohm pull-down resistor on D-.
0b : Pull-down resistor not connected to D-.
1b : Pull-down resistor connected to D-.
DischrgVbus
3
rd/wr/s/c
0b
Discharge VBUS through a resistor. A minimum of 656Ω is
defined in the OTG specification [Ref 2]. If the Link sets this bit
to 1, it waits for an RX CMD indicating SessEnd has
transitioned from 0 to 1, and then resets this bit to 0 to stop the
discharge.
0b : do not discharge VBUS
1b : discharge VBUS
ChrgVbus
4
rd/wr/s/c
0b
Charge VBUS through a resistor. Used for VBUS pulsing SRP. A
minimum of 281Ω output impedance with a voltage source of
3.0V is one example given in the OTG specification [Ref 2]. The
Link must first check that VBUS has been discharged (see
DischrgVbus bit), and that both D+ and D- data lines have
been low (SE0) for 2ms.
0b : do not charge VBUS
1b : charge VBUS
DrvVbus
5
rd/wr/s/c
0b
Signals the internal charge pump or external supply to drive 5V
on VBUS.
0b : do not drive Vbus (default)
1b : drive 5V on Vbus
DrvVbus
External
6
rd/wr/s/c
0b
Selects between the internal and the external 5V Vbus supply.
This bit is optional and does not need to be present if only one
Vbus power source is supported.
0b : Drive Vbus using the internal charge pump (default).
Support of an internal charge pump is optional.
1b : Drive Vbus using external supply. Support of an external
Vbus power source is optional.
UseExternal
VbusIndicator
7
rd/wr/s/c
0b
Tells the PHY to use an external VBUS over-current indicator.
This bit is optional. Refer to 3.8.7.3.
0b: Use the internal OTG comparator (VA_VBUS_VLD) or internal
VBUS valid indicator (default).
1b: Use external VBUS valid indicator signal
Table 24 – OTG Control register
16
If the Carkit Mode registers are implemented, the pull-up resistor and detection circuitry shall comply with [Ref 6].
71
4.2.5
October 20, 2004
USB Interrupt Enable Rising
Address: 0Dh-0Fh (Read), 0Dh (Write), 0Eh (Set), 0Fh (Clear).
If set, the bits in this register cause an interrupt event notification to be generated when the corresponding
PHY signal changes from low to high. By default, all transitions are enabled. RxActive and RxError must
always be communicated immediately and so are not included in this register. Interrupt circuitry can be
powered down in any mode when both rising and falling edge enables are disabled. To ensure interrupts are
detectable when clock is powered down, the link should enable both rising and falling edges.
Field name
Bits
Access
Reset
Hostdisconnect
Rise
0
rd/wr/s/c
1b
Generate an interrupt event notification when
Hostdisconnect changes from low to high. Applicable
only in host mode (DpPulldown and DmPulldown both
set to 1b).
VbusValid Rise
1
rd/wr/s/c
1b
Generate an interrupt event notification when VbusValid
changes from low to high.
SessValid Rise
2
rd/wr/s/c
1b
Generate an interrupt event notification when SessValid
changes from low to high. SessValid is the same as
UTMI+ AValid.
SessEnd Rise
3
rd/wr/s/c
1b
Generate an interrupt event notification when SessEnd
changes from low to high.
IdGnd Rise
4
rd/wr/s/c
1b
Generate an interrupt event notification when IdGnd
changes from low to high. IdGnd is valid 50ms after
IdPullup is set to 1b, otherwise IdGnd is undefined and
should be ignored.
7:5
rd/wr/s/c
0b
Reserved.
Reserved
Description
Table 25 – USB Interrupt Enable Rising register
72
4.2.6
October 20, 2004
USB Interrupt Enable Falling
If set, the bits in this register cause an interrupt event notification to be generated when the corresponding
PHY signal changes from high to low. By default, all transitions are enabled. RxActive and RxError must
always be communicated immediately and so are not included in this register. Interrupt circuitry can be
powered down in any mode when both rising and falling edge enables are disabled. To ensure interrupts are
detectable when clock is powered down, the link should enable both rising and falling edges.
Field name
Bits
Access
Reset
Description
Hostdisconnect
Fall
0
rd/wr/s/c
1b
Generate an interrupt event notification when
Hostdisconnect changes from high to low. Applicable
only in host mode.
VbusValid Fall
1
rd/wr/s/c
1b
Generate an interrupt event notification when VbusValid
changes from high to low.
SessValid Fall
2
rd/wr/s/c
1b
Generate an interrupt event notification when SessValid
changes from high to low. SessValid is the same as
UTMI+ AValid.
SessEnd Fall
3
rd/wr/s/c
1b
Generate an interrupt event notification when SessEnd
changes from high to low.
IdGnd Fall
4
rd/wr/s/c
1b
Generate an interrupt event notification when IdGnd
changes from high to low. IdGnd is valid 50ms after
IdPullup is set to 1b, otherwise IdGnd is undefined and
should be ignored.
Reserved
7:5
rd/wr/s/c
0b
Reserved.
Table 26 – USB Interrupt Enable Falling register
73
4.2.7
October 20, 2004
USB Interrupt Status
Address: 13h (Read-only).
Indicates the current value of the interrupt source signal. Interrupt circuitry can be powered down in any
mode when both rising and falling edge enables are disabled. To ensure interrupts are detectable when
clock is powered down, the link should enable both rising and falling edges.
Field name
Bits
Access
Reset
Hostdisconnect
0
rd
0b
Current value of UTMI+ Hostdisconnect output.
Applicable only in host mode. Automatically reset to 0b
when Low Power Mode is entered.
VbusValid
1
rd
0b
Current value of UTMI+ VbusValid output.
SessValid
2
rd
0b
Current value of UTMI+ SessValid output. SessValid is
the same as UTMI+ AValid.
SessEnd
3
rd
0b
Current value of UTMI+ SessEnd output.
IdGnd
4
rd
0b
Current value of UTMI+ IdGnd output. IdGnd is valid
50ms after IdPullup is set to 1b, otherwise IdGnd is
undefined and should be ignored.
7:5
rd
Xb
Reserved.
Reserved
Description
Table 27 – USB Interrupt Status register
74
4.2.8
October 20, 2004
USB Interrupt Latch
Address: 14h (Read-only with auto-clear).
These bits are set by the PHY when an unmasked change occurs on the corresponding internal signal. The
PHY will automatically clear all bits when the Link reads this register, or when Low Power Mode is entered.
The PHY also clears this register when Serial Mode or Carkit Mode is entered regardless of the value of
ClockSuspendM. Interrupt circuitry can be powered down in any mode when both rising and falling edge
enables are disabled. To ensure interrupts are detectable when clock is powered down, the link should
enable both rising and falling edges.
The PHY must follow the rules in Table 29 for setting any latch register bit. It is important to note that if
register read data is returned to the Link in the same cycle that a USB Interrupt Latch bit is to be set, the
interrupt condition is given immediately in the register read data and the Latch bit is not set.
Note that it is optional for the Link to read the USB Interrupt Latch register in Synchronous Mode because
the RX CMD byte already indicates the interrupt source directly.
Field name
Bits
Access
Reset
Hostdisconnect
Latch
0
rd
0b
Set to 1b by the PHY when an unmasked event occurs
on Hostdisconnect. Cleared when this register is read.
Applicable only in host mode.
VbusValid Latch
1
rd
0b
on VbusValid. Cleared when this register is read.
SessValid Latch
2
rd
0b
on SessValid. Cleared when this register is read.
SessValid is the same as UTMI+ AValid.
SessEnd Latch
3
rd
0b
on SessEnd. Cleared when this register is read.
IdGnd Latch
4
rd
0b
on IdGnd. Cleared when this register is read. IdGnd is
valid 50ms after IdPullup is set to 1b, otherwise IdGnd
is undefined and should be ignored.
7:5
rd
0b
Reserved.
Reserved
Description
Table 28 – USB Interrupt Latch register
Input Conditions
Resultant value of
Latch Register bit
Register read data returned
in current clock cycle
Interrupt Latch bit is to be set
in current clock cycle
No
No
0
No
Yes
1
Yes
No
0
Yes
Yes
0
Table 29 – Rules for setting Interrupt Latch register bits
75
4.2.9
October 20, 2004
Debug
Indicates the current value of various signals useful for debugging.
Field name
Bits
Access
Reset
LineState0
0
rd
0b
Contains the current value of LineState(0)
LineState1
1
rd
0b
Contains the current value of LineState(1)
7:2
rd
0b
Reserved.
Reserved
Description
Table 30 – Debug register
4.2.10
Scratch Register
Field name
Bits
Access
Reset
Scratch
7:0
rd/wr/s/c
00h
Description
Empty register byte for testing purposes. Software can
read, write, set, and clear this register and the PHY
functionality will not be affected.
Table 31 – Scratch register
76
4.2.11
October 20, 2004
Carkit Control
Address: 19h-1Bh (Read), 19h (Write), 1Ah (Set), 1Bh (Clear).
This register is optional. Controls the operation of the carkit circuitry within the PHY. The TxdEn and RxdEn
bits are ignored if the CarkitMode bit in the Interface Control register is not set. If the CarkitMode bit is
set, and the RxdEn bit is not set, then the data(1) pin is held at logic high.
Field name
Bits
Access
Reset
Description
CarkitPwr
0
rd/wr/s/c
0b
Applies power to carkit circuitry.
IdGndDrv
1
rd/wr/s/c
0b
Drives ID pin to ground.
TxdEn
2
rd/wr/s/c
0b
Routes TXD signal from data(0) pin onto D- pin.
RxdEn
3
rd/wr/s/c
0b
Routes RXD signal from D+ pin to data(1) pin.
SpkLeftEn
4
rd/wr/s/c
0b
Routes audio signal from SPKR_L pin to D- pin.
SpkRightEn
5
rd/wr/s/c
0b
Routes audio signal from SPKR_MIC pin D+ pin.
MicEn
6
rd/wr/s/c
0b
Routes audio signal from D+ pin to SPKR_MIC pin.
Reserved
7
-
Xb
Reserved.
Table 32 – Carkit Control Register
4.2.12
Carkit Interrupt Delay
Address: 1Ch (Read), 1Ch (Write).
This register is optional. When a carkit interrupts a phone, it pulls D+ low for an extended period of time. As
per [Ref 6], the phone must detect an interrupt if D+ is below the VPH_DP_LO voltage threshold for a time of
TPH_DP_INT.
The Carkit Interrupt Timer in the PHY is enabled whenever the CarIntDet bit in the Carkit Interrupt Enable
register is set. If enabled, the Carkit Interrupt Timer increments when the D+ voltage is below VPH_DP_LO. If
the D+ voltage is above VPH_DP_LO, then the Carkit Interrupt Timer resets. The Carkit Interrupt Timer must
reset when D+ is above VPH_DP_LO for times as short as TCR_INJ_WDTH.
When the Carkit Interrupt Timer reaches the value stored in CarIntDly, the CarIntDet bit in the Carkit
Interrupt Latch register is set and an interrupt is generated.
Field name
Bits
Access
Reset
CarIntDly
7:0
rd/wr
18h
Description
Sets interrupt time in units of 0.25 ms.
Table 33 – Carkit Interrupt Delay register
77
4.2.13
October 20, 2004
Carkit Interrupt Enable
Address: 1Dh-1Fh (Read), 1Dh (Write), 1Eh (Set), 1Fh (Clear).
This register is optional. If set, the bits in this register cause an interrupt event notification to be generated
when the corresponding PHY signal changes. By default, all bits in this register are cleared.
Field name
Bits
Access
Reset
IdFloat Rise
0
rd/wr/s/c
0b
Generate an interrupt event notification when the ID pin
changes from not floating to floating. The IdPullup bit in the
OTG Control register must be set, and the ID pull-up and
detection circuitry must conform to that defined in [Ref 6].
IdFloat Fall
1
rd/wr/s/c
0b
Generate an interrupt event notification when the ID pin
changes from floating to not floating. The IdPullup bit in the
OTG Control register must be set, and the ID pull-up and
detection circuitry must conform to that defined in [Ref 6].
CarIntDet
2
rd/wr/s/c
0b
Generate an interrupt event notification when the Carkit
Interrupt Timer reaches the value stored in the Carkit
Interrupt Delay register.
CarDp Rise
3
rd/wr/s/c
0b
Generate an interrupt event notification when a rising voltage
on the D+ line crosses the VPH_DP_LO threshold.
CarDp Fall
4
rd/wr/s/c
0b
Generate an interrupt event notification when a falling voltage
on the D+ line crosses the VPH_DP_LO threshold.
7:5
rd/wr/s/c
0b
Reserved.
Reserved
Description
Table 34 – Carkit Interrupt Enable register
4.2.14
Carkit Interrupt Status
This register is optional. When a carkit interrupt event notification occurs, the link can read this register to
determine which event triggered the interrupt.
Field name
Bits
Access
Reset
IdFloat
0
rd
0b
Asserted when the ID pin is floating.
CarIntDet
1
rd
0b
Asserted when the CarIntDet bit in the Carkit Interrupt Latch
register is set.
CarDp
2
rd
0b
Asserted when the D+ line is above the VPH_DP_LO threshold.
7:3
rd
0b
Reserved.
Reserved
Description
Table 35 – Carkit Interrupt Status Register
78
4.2.15
October 20, 2004
Carkit Interrupt Latch
Address: 21h (Read-only with auto-clear).
This register is optional. These bits are set by the PHY when an unmasked carkit event occurs. The PHY will
automatically clear all bits when the Link reads this register, or when Low Power Mode is entered.
The PHY must follow the rules in Table 29 for setting any latch register bit. It is important to note that if
register read data is returned to the Link in the same cycle that a Carkit Interrupt Latch bit is to be set, the
interrupt condition is given immediately in the register read data and the latch bit is not set.
Field name
Bits
Access
Reset
IdFloat Latch
0
rd
0b
Asserted if the IdFloat Rise bit in the Carkit Interrupt
Enable register is set, and the ID line changes from not
floating to floating. Also asserted if the IdFloat Fall bit in
the Carkit Interrupt Enable register is set, and the ID line
changes from floating to not floating.
CarIntDet Latch
1
rd
0b
Asserted if the CarIntDet bit in the Carkit Interrupt Enable
register is set, and the Carkit Interrupt Timer reaches the
value stored in the Carkit Interrupt Delay register.
CarDp Latch
2
rd
0b
Asserted if the CarDp Rise bit in the Carkit Interrupt
Enable register is set, and the D+ line rises above the
VPH_DP_LO threshold. Also asserted if the CarDp Fall bit is
set, and the D+ line falls below the VPH_DP_LO threshold.
7:3
rd
0b
Reserved.
Reserved
Description
Table 36 – Carkit Interrupt Latch register
4.2.16
Carkit Pulse Control
This register is optional. It controls the operation of the carkit data-during-audio function within the PHY. The
TxPlsEn and RxPlsEn bits are ignored if the CarkitMode bit in the Interface Control register is not set.
Field name
Bits
Access
Reset
TxPlsEn
0
rd/wr/s/c
0b
Enables data-during-audio pulse transmit
RxPlsEn
1
rd/wr/s/c
0b
Enables data-during-audio pulse receive
SpkrLeftBiasEn
2
rd/wr/s/c
0b
Enables bias for left speaker.
SpkrRightBiasEn
3
rd/wr/s/c
0b
Enables bias for right speaker.
7:4
-
0000b
Reserved
Description
Reserved.
Table 37 – Carkit Pulse Control
TxPlsEn
When the TxPlsEn bit is set, and the SpkLeftEn bit in the Carkit Control register is set, then the PHY shall
output a positive pulse followed by a negative pulse on the D- line after each rising or falling edge on the
79
October 20, 2004
data(0) line. When generating such a pulse pair, the PHY shall perform the steps, as defined in the Carkit
specification [Ref 6]. The following list of steps provides information on the intent of the Carkit specification.
•
•
•
•
•
•
•
tri-state the speaker buffer that drives the D- line
drive the D- line to a voltage of 3.3V +/- 10%
wait for the time specified in the Transmit Positive Width register
drive the D- line to ground
wait for the time specified in the Transmit Negative Width register
stop driving the D- line to ground
enable the speaker buffer that drives the D- line
RxPlsEn
When the RxPlsEn bit is set, and the MicEn bit in the Carkit Control register is set, then the PHY shall
toggle the data(1) output each time a falling edge is detected on the D+ line that crosses the carkit interrupt
threshold of VPH_DP_LO. When the RxPlsEn bit is set, the Receive Polarity Recovery timer shall be
enabled.
4.2.17
Transmit Positive Width
Address: 25h (Read), 25h (Write)
This register is optional. It specifies the width of the positive pulse that is output on the D- line when the
TxPlsEn bit is set. The time is measured in units of 60MHz clock periods. The minimum TxPosWdth that
must be supported is 8. The maximum TxPosWdth that must be supported is 64.
Field name
Bits
Access
Reset
TxPosWdth
7:0
rd/wr
10h
Description
Transmit positive pulse width
Table 38 – Transmit Positive Width
4.2.18
Transmit Negative Width
This register is optional. It specifies the width of the negative pulse that is output on the D- line when the
TxPlsEn bit is set. The time is measured in units of 60MHz clock periods. The minimum TxNegWdth that
must be supported is 8. The maximum TxNegWdth that must be supported is 64.
Field name
Bits
Access
Reset
TxNegWdth
7:0
rd/wr
20h
Description
Transmit negative pulse width
Table 39 – Transmit Negative Width
4.2.19
Receive Polarity Recovery
This register is optional.
When the data-during-audio feature is enabled in the Carkit [Ref 6], then the carkit sends UART data to the
phone by converting the non-return-to-zero (NRZ) UART signal into a series of pulses, and transmitting
80
October 20, 2004
these pulses to the phone on the D+ line. The PHY in the phone then converts these pulses back into an
NRZ UART signal by toggling to the data(1) line each time a pulse is received. If the PHY were to
erroneously miss a pulse, or detect an extra pulse, then the polarity on the data(1) line would be incorrect.
To recover from this condition, the PHY automatically resets the polarity of the data(1) line to logic high
whenever the polarity of the data(1) line has been logic low for the time specified in the Receive Polarity
Recovery register.
The Receive Polarity Recovery is only active if the RxPlsEn bit in the Carkit Pulse Control register is set.
The time is measured in units of 0.25ms. The minimum RxPolRcvry that must be supported is 1. The
maximum RxPolRcvry that must be supported is 255.
Field name
Bits
Access
Reset
RxPolRcvry
7:0
rd/wr
02h
Description
Receive polarity recovery time
Table 40 – Receive Polarity Recovery
4.2.20
Reserved
Address: 28h-2Eh.
These registers are reserved for future use.
4.2.21
Access Extended Register Set
Address: 2Fh (Read/Write).
Accesses the extended register set. See 3.8.3.4 for an explanation of Extended Register accesses.
4.2.22
Vendor-specific
Address: 30h-3Fh.
Allocated for vendor-specific use.
4.3
Extended Register Set
Addresses 00h to 3Fh of the Extended Register Set map directly into the Immediate Set defined in 4.2. A
read, write, set, or clear operation to extended address 00h to 3Fh operates on the immediate register set.
Addresses 40h to 7Fh are reserved for future use. Addresses 80h to FFh are allocated for Vendor-specific
use.
4.4
Register Settings for all Upstream and Downstream signalling modes
Table 41 shows what register settings must be applied by the Link to achieve the desired signalling mode.
The PHY must generate the correct signalling, prepend the SYNC and append the EOP automatically as
required. The table also shows which resistors are enabled as a result of the register settings. The following
signals conceptually exist inside the PHY. All resistor signals are active high, a value of 1b enables the
resistor, a value of 0b disables the resistor.
•
•
•
•
•
rpu_dp_en enables the 1.5kΩ pull-up resistor on D+
rpu_dm_en enables the 1.5kΩ pull-up resistor on Drpd_dp_en enables the 15kΩ pull-down resistor on D+
rpd_dm_en enables the 15kΩ pull-down resistor on Dhsterm_en enables the 45Ω termination resistors on D+ and D-
81
October 20, 2004
TermSelect
OpMode
DpPulldown
DmPulldown
rpu_dp_en
rpu_dm_en
rpd_dp_en
rpd_dm_en
hsterm_en
Resistor Settings
XcvrSelect
Register Settings
Tristate Drivers
XXb
Xb
01b
Xb
Xb
0b
0b
0b
0b
0b
Power-up or Vbus < Vth(SESSEND)
01b
0b
00b
1b
1b
0b
0b
1b
1b
0b
Host Chirp
00b
0b
10b
1b
1b
0b
0b
1b
1b
1b
Host Hi-Speed
00b
0b
00b
1b
1b
0b
0b
1b
1b
1b
Host Full Speed
X1b
1b
00b
1b
1b
0b
0b
1b
1b
0b
Host HS/FS Suspend
01b
1b
00b
1b
1b
0b
0b
1b
1b
0b
Host HS/FS Resume
01b
1b
10b
1b
1b
0b
0b
1b
1b
0b
Host Low Speed
10b
1b
00b
1b
1b
0b
0b
1b
1b
0b
Host Low Speed Suspend
10b
1b
00b
1b
1b
0b
0b
1b
1b
0b
Host Low Speed Resume
10b
1b
10b
1b
1b
0b
0b
1b
1b
0b
Host Test_J/Test_K
00b
0b
10b
1b
1b
0b
0b
1b
1b
1b
Peripheral Chirp
00b
1b
10b
0b
0b
1b
0b
0b
0b
0b
Peripheral Hi-Speed
00b
0b
00b
0b
0b
0b
0b
0b
0b
1b
Peripheral Full Speed
01b
1b
00b
0b
0b
1b
0b
0b
0b
0b
Peripheral HS/FS Suspend
01b
1b
00b
0b
0b
1b
0b
0b
0b
0b
Peripheral HS/FS Resume
01b
1b
10b
0b
0b
1b
0b
0b
0b
0b
Peripheral Low Speed
10b
1b
00b
0b
0b
0b
1b
0b
0b
0b
Peripheral Low Speed Suspend
10b
1b
00b
0b
0b
0b
1b
0b
0b
0b
Peripheral Low Speed Resume
10b
1b
10b
0b
0b
0b
1b
0b
0b
0b
Peripheral Test_J/Test_K
00b
0b
10b
0b
0b
0b
0b
0b
0b
1b
OTG device, Peripheral Chirp
00b
1b
10b
0b
1b
1b
0b
0b
1b
0b
OTG device, Peripheral Hi-Speed
00b
0b
00b
0b
1b
0b
0b
0b
1b
1b
OTG device, Peripheral Full Speed
01b
1b
00b
0b
1b
1b
0b
0b
1b
0b
OTG device, Peripheral HS/FS Suspend
01b
1b
00b
0b
1b
1b
0b
0b
1b
0b
OTG device, Peripheral HS/FS Resume
01b
1b
10b
0b
1b
1b
0b
0b
1b
0b
OTG device, Peripheral Test_J/Test_K
00b
0b
10b
0b
1b
0b
0b
0b
1b
1b
Signalling mode
General Settings
Host Settings
Peripheral Settings
Table 41 – Upstream and downstream signalling modes
82
5.
October 20, 2004
T&MT Connector
5.1
General
This chapter specifies the Transceiver and Macrocell Tester’s (T&MT) mechanical and electrical interface for
testing the ULPI PHY. The T&MT is typically a ULPI Link FPGA/ASIC board, and the PHY daughter-card
(UUT) is plugged onto this.
The daughter-card and placement of the interfacing connector are shown in this chapter. The connector pin
assignment is described here using the naming convention of the UTMI+ Low Pin Interface and the original
T&MT specification [Ref 7].
The ULPI T&MT interface has the following features:
•
•
•
•
•
•
•
5.2
100 pin Amp connector.
Maintains compatibility with UTMI and UTMI+ T&MT connector pin assignments where possible.
Routes all ULPI digital interface pins between Link and PHY.
Provides 15 general-purpose I/O pins for vendor-specific functions.
Multiple power and ground pins.
Switchable VBUS power control.
Defines separate I/O voltage pins. I/O voltage is vendor-specific. Typical I/O voltages include 3.3
±0.3V and 1.8 ±0.15V.
Daughter-card (UUT) Specification
The PHY IC resides on the daughter-card. Daughter-card dimensions are given in the T&MT specification
[Ref 7]. An example daughter-card and PCI-based Link board is depicted in Figure 60. Note the orientation
of the 100 pin Amp connector and the USB connector.
PHY
IC
Link ASIC/FPGA board
Amp 2-557100-5
USB
receptacle
Amp 2-557101-5
PHY daughter-card
Link
ASIC/FPGA
PCI connector
Figure 60 – Recommended daughter-card configuration (not to scale)
83
October 20, 2004
With the daughter-card viewed from the backside of the Amp connector (USB receptacle side), and with the
Amp connector at the bottom, the connector pin numbers are shown in Table 42. Pins shown in blue are
ground pins, red indicates power pins, and green indicates I/O power pins.
49
50
99
100
47
48
97
98
45
46
95
96
43
44
93
94
41
42
91
92
39
40
89
90
37
38
87
88
35
36
85
86
33
34
83
84
31
32
81
82
29
30
79
80
27
28
77
78
25
26
75
76
23
24
73
74
21
22
71
72
19
20
69
70
17
18
67
68
15
16
65
66
13
14
63
64
11 9 7 5 3 1
12 10 8 6 4 2
61 59 57 55 53 51
62 60 58 56 54 52
Table 42 – T&MT connector pin view
The Amp connector on the daughter-card has the pin assignment shown in Table 43. A description of each
pin is given in Table 44.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
GPIO0
GND
GPIO2
GND
GPIO4
GPIO5
GPIO7
VDD
GND
Reserved
GPIO9
GPIO11
GND
Reserved
SPKR_L
VDD
reset
Reserved
Reserved
Reserved
GND
Reserved
Reserved
GND
Reserved
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
GPIO1
GND
VBUS_out
GPIO3
Reserved
data7
GND
data5
data3
GND
data1
Reserved
VIO
GND
Reserved
Reserved
Reserved
GND
Reserved
SPKR_MIC
GND
VBUS_in
Reserved
dc_psnt_n
GPIO13
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
GND
sys_clk
GND
GND
Reserved
GPIO6
VDD
GPIO8
Reserved
Reserved
GPIO10
GND
GPIO12
Reserved
GND
Reserved
Reserved
GND
VDD
dir
nxt
Reserved
GND
Reserved
Reserved
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
Table 43 – T&MT connector pin allocation
84
GND
Reserved
GPIO14
Reserved
GND
VIO
data6
data4
GND
data2
data0
VIO
Reserved
Reserved
clock
Reserved
GND
Reserved
Reserved
GND
stp
Reserved
Reserved
Reserved
psu_shd_n
October 20, 2004
Direction
on UUT
Active
Level
clock
I/O
n/a
Clock pin. Can be output from the PHY and/or input from the Link.
data0-7
I/O
n/a
ULPI bi-directional data bus.
dir
Output
High
ULPI dir signal.
stp
Input
n/a
ULPI stp signal.
nxt
Output
n/a
ULPI nxt signal.
Input
High
Optional reset pin.
dc_psnt_n
Output
Low
When low, the Link detects the presence of the daughter-card. A
pull-down resistor of 200Ω is required
psu_shd_n
Input
Low
When low, the PHY power supply unit is shutdown and can be
sourced from the Link through the T&MT connector pins.
sys_clk
Input
n/a
Optional vendor-specific input clock.
Reserved
I/O
n/a
Reserved.
GPIO0-14
I/O
n/a
General Purpose I/O. Spare interconnects between the UUT and
T&MT.
GND
I/O
n/a
Ground plane.
VBUS_in
I/O
n/a
Used by the Link to monitor VBUS pin of the USB connector.
VBUS_out
I/O
n/a
5 Volt supply from the Link. Used primarily by the PHY for driving
VBUS. The Link controls VBUS using the DrvVbusExternal register
bit in the PHY.
VDD
I/O
n/a
PHY power supply.
VIO
I/O
n/a
Vendor-specific pad ring power supply. The voltage on VIO
determines the switching thresholds of the ULPI interface signals.
Input
n/a
In carkit mono mode, inputs mono speaker signal. In carkit stereo
mode inputs left speaker signal.
I/O
n/a
In carkit mono mode, outputs microphone signal. In carkit stereo
mode, inputs right speaker signal.
Name
reset
SPKR_L
SPKR_MIC
Description
Table 44 – T&MT pin description
85

UTMI+ Low Pin Interface (ULPI) Specification

Transcription

Similar documents

EMUKEY Product Sheet

What does it measure? The Visioscan® VC 98 USB is a special UVA

Convert your laptop to a desktop in seConds!

portable usb dj mixer + scratch controll er + dj software

MiXiM - CCS Labs

3.5" SATA to USB 3.0 External Hard Drive Enclosure

SC-2300 spec

Charging your PowerSLIMTM 9.0 - eshop x

www.globo.com.pl OPTICUM HD 9600 PRIMA id: O9600PRIMA

AccuPower hardware