Instructions - Honda Parts Super Store

INSTALLATION
INSTRUCTIONS
Accessory
Application
FRONT UNDER SPOILERS
P/N 08F01-T3L-100A
2016 ACCORD
2-DOOR
Publications No.
VERSION 1
Issue Date
AUG 2015
PARTS LIST
TOOLS AND SUPPLIES REQUIRED
Right front under spoiler
Phillips screwdriver
Drill
3 mm, 6 mm, 8 mm, and 10 mm Drill bits
Eye protection (face shield, safety goggles, etc.)
File
Pushpin
Tape
Masking tape
Blanket
Diagonal cutters
10 mm Open end wrench
The following tool is available through the Honda Tool and
Equipment Program. On the iN, click on: Service >
Service Bay > Tool and Equipment Program, then enter
the number under “Search”. Or, call 888-424-6857.
• Rubber Roller (T/N MHLE54D)
Left front under spoiler
4
Clips
4
Bumper clips A
Illustration of the Front Under Spoilers on the Vehicle
2
Bumper clips B (long)
4
Washers
2
Self-tapping screws
2
RIGHT FRONT
UNDER SPOILER
Alcohol swabs
© 2015 American Honda Motor Co., Inc. – All Rights Reserved.
AII02174-14 (1508)
LEFT FRONT
UNDER SPOILER
08F01-T3L-1000-9A
QE30201AC
1 of 6
INSTALLATION
3.
Remove the front grille cover.
4 CLIPS
Customer Information: The information in this
installation instruction is intended for use only by skilled
technicians who have the proper tools, equipment, and
training to correctly and safely add equipment to your
vehicle. These procedures should not be attempted by
“do-it-yourselfers.”
FRONT GRILLE
COVER
NOTE:
• Do not damage the paint finish.
• This kit should be installed only if the ambient air
temperature is 15°C (60°F) or above.
• Clean the areas to be covered.
• To allow the adhesive to cure, do not wash the vehicle
for 24 hours. Please advise the customer.
1. Disconnect the negative cable from the battery.
2. Attach masking tape to the front bumper, headlights
and front fenders as shown.
QE13005AG
4.
RIGHT
HEADLIGHT
LEFT
HEADLIGHT
Remove the front bumper.
• Remove the four self-tapping screws and ten
clips.
SELF-TAPPING
SCREW
(Discard.)
2 SELF-TAPPING
SCREWS
FRONT
BUMPER
LEFT FRONT
FENDER
CLIP
(Discard.)
8 CLIPS
MASKING
TAPE
QE13004AG
CLIP
(Discard.)
2 of 6
SELFTAPPING
SCREW
CLIP
(Discard.)
BOTTOM VIEW (Discard.)
AII02174-14 (1508)
8 CLIPS
CLIP
(Discard.)
QE13006AG
© 2015 American Honda Motor Co., Inc. – All Rights Reserved.
•
Release the four retaining tabs on each side.
•
•
4 RETAINING
TABS
•
Remove the two clips.
With the help of an assistant, remove the front
bumper.
Place the front bumper on a blanket.
VEHICLE
CONNECTOR
(if equipped)
FRONT BUMPER
•
2 CLIPS
VEHICLE
CONNECTOR
(if equipped)
QE13007AG
Release the four retaining tabs on each side.
FRONT
BUMPER
QE13009AG
4 RETAINING
TABS
5.
Using a pushpin, pierce the inside of the front
bumper through the center of the four scribe marks.
PUSHPIN
FRONT
BUMPER
SCRIBE
MARKS
(Do not
pierce.)
4 SCRIBE
MARKS
4 MARKS
FRONT BUMPER
QE13008AG
FRONT
BUMPER
QE60401AG
© 2015 American Honda Motor Co., Inc. – All Rights Reserved.
AII02174-14 (1508)
3 of 6
6.
While wearing eye protection, drill the four pierced
marks to 10 mm.
• First drill with a 3 mm drill bit, and then with a
6 mm drill bit, with an 8 mm drill bit, and finish
with a 10 mm drill bit. Remove any burrs.
8.
Using one alcohol swab, thoroughly clean the front
bumper where the left front under spoiler will attach.
FRONT
BUMPER
FRONT
BUMPER
Clean with an
alcohol swab.
4 MARKS
9.
3 mm
6 mm
8 mm
10 mm
DRILL BITS
ALCOHOL
SWAB
QE60403AG
Install the left front under spoiler to the front bumper.
LEFT FRONT
UNDER SPOILER
2 CLIPS
DRILL
QE60402AG
7.
Peel back the adhesive backings, and tape them to
the front surface of the left front under spoiler with
masking tape.
3 ADHESIVE
BACKINGS
(Peel.)
MASKING
TAPE
FRONT
BUMPER
QE60404AG
LEFT FRONT
UNDER SPOILER
QE30211BC
4 of 6
AII02174-14 (1508)
© 2015 American Honda Motor Co., Inc. – All Rights Reserved.
10. Secure the left front under spoiler with two clips.
NOTE: Do not push the clip too tightly, or it may
deform the left front under spoiler. Readjust the clips,
if necessary.
13. With the help of an assistant, install the front bumper
on the vehicle.
SELF-TAPPING
SCREW
(supplied)
FRONT
BUMPER
2 SELF-TAPPING
SCREWS
SELFTAPPING
SCREW
(supplied)
8 CLIPS
4 WASHERS
4 BUMPER
CLIPS A
2 BUMPER
CLIPS B
(LONG)
BOTTOM VIEW
2 BUMPER
CLIPS A
2 CLIPS
Cut off.
2 BUMPER
CLIPS A
QE60405AG
11. Cut off the excess from the clips.
12. Repeat steps 5 through 11 to install the right front
under spoiler.
BUMPER
CLIP B
(LONG)
8 CLIPS
BUMPER
CLIP B
(LONG)
QE60406AG
14. Secure the left and right front under spoilers to the
front bumper with four bumper clips A, two bumper
clips B (long), four washers, and two self-tapping
screws.
© 2015 American Honda Motor Co., Inc. – All Rights Reserved.
AII02174-14 (1508)
5 of 6
15. While applying light pressure against the left front
under spoiler, carefully remove the adhesive
backings.
FRONT
BUMPER
LEFT FRONT
UNDER SPOILER
19. Check that all wire harnesses are routed properly
and all connectors are plugged in.
20. Install all removed parts.
21. Connect the negative cable to the battery.
22. Press and hold the audio unit power button for two
seconds to restore the audio and navi (if equipped)
system functions.
23. Reset the clock (on vehicles without navigation).
3 ADHESIVE
BACKINGS
(Remove.)
QE60407AG
16. Using your hand, firmly press the left front under
spoiler against the front bumper for 30 seconds.
17. Using a rubber roller, apply firm pressure while
rolling to set the adhesive, especially at the ends.
FRONT
BUMPER
RUBBER
ROLLER
LEFT FRONT
UNDER SPOILER
QE60408AG
18. Repeat steps 15 through 17 to install the right front
under spoiler.
6 of 6
AII02174-14 (1508)
© 2015 American Honda Motor Co., Inc. – All Rights Reserved.