Flextray NEW Catalog 02/04 Q

Transcription

welcome to flextray
welcome to flextray
This Cable Management System is the time and money
saving alternative to traditional cable tray systems.
FLEXTRAY’s innovative steel mesh design enables faster installation
with less labor and materials. The open mesh design enables cable
networks to be expanded quickly and easily – it is ideal for
today’s sensitive telecommunications and fiber optic cables.
FLEXTRAY is available in a variety of finishes and depths of 11/2”, 2”, 4” and 6”. Widths range from 2” to 34” to meet your
cabling needs. Installation of the FLEXTRAY Cable Management
System is simple. A CLEANSHEAR® Cutter and installation tool are
all that’s needed. And, with FLEXTRAY’s complete line of accessories
and mounting options – you can easily navigate any environment.
THICKEST GAUGE METAL
FLEXTRAY minimum 5mm gauge steel is at least 30%
stronger than competitor’s lesser gauge steel.
BUILT-IN SAFETY
“T” weld safety edge construction eliminates sharp edges -avoiding injury to hands and damage to cable.
www.flextray.com
1
table of contents
2
where to use flextray
UL Classified
4
flextray straight sections
Flextray meets all applicable UL
standard requirements regarding
tray used as an equipment
ground conductor. See page
5 on Flextray sizes that meet
these standards.
CSA Approved
(Canadian Standards Association)
FLEXTRAY is an approved cable
management system for
supporting communications and
optical fiber cables. FLEXTRAY
complies with T.I.L. No. J-26
prepared by CSA, and was
formally approved by the
subcommittee on CSA Standard
C22.2 No. 126.
Sizes, Finishes, Load & Fill Tables, UL classified sizes
6
Bolted, Flexmate, Spring Splice, Coil Splice, UL Splice Information
8
Union Made
Flextray is made by United Steel
Workers Union – Local 7252
Safe
Only FLEXTRAY offers clean,
smooth burr-free cuts every time
with CLEANSHEAR Cutters. Our
“T-weld” design allows easy side
loading of cable without
damaging cable or hands.
Union Made in the USA
support methods
Ceiling types, Wall types, Underfloor types
13
accessories
Drop-outs, Rack Attachments, Hold Down Clips, Dividers, Covers, Solid Bottom Inserts
Conduit Fitting Attachments, Grounding Accessories
16
hardware
Ceiling Anchors, Threaded Rod, Nuts, Washers, Beam Clamps, Metal Framing, Spring Nuts
18
flextray convenience kits
FlexPack, Rack Pack
Made in the USA
Flextray is the only wire mesh
cable tray fully constructed in
the U.S.A.
splice methods
19
RF raised floor system
RF components and accessories
23
cutting tools
Cleanshear, Cleanshear with Bending Attachment, AirShear
25
creating fittings
Making Horizontal Bends, Making Tees, Making Crosses, Making Vertical fittings
32
design/technical tools
33
CSI specification
33
index
Need Help? Call Toll Free 1-888-353-9879 or email flextray@gsmetals.com
table of contents
flextray is…
2
Ceiling and Plenum Spaces
FLEXTRAY Cable Management System installs
in plenum applications faster and with
greater flexibility than standard tray.
Installers can bend, curve, drop or avoid
any obstacle -- adjustments can be made
on-site without delays.
www.flextray.com
3
Raised Access Floors
Today’s computer environment requires a
cable management system that supports
today’s sophisticated cables and can quickly
be expanded for additional runs -FLEXTRAY Cable Management System meets
all these requirements.
Telecommunication Closets
FLEXTRAY‘s open ventilated steel mesh
design provides endless locations to secure
cable and enables easy identification.
FLEXTRAY’s many parts, widths and depths
make organizing the closet simple.
4
straight sections
Flextray straight sections come in 10’ lengths. These are the main components to your pathway installation.
straight sections
Make straight runs, horizontal and vertical changes from these sizes:
FLEXTRAY PART #
2 inch depth
4 inch depth
6 inch depth
Depth
Width
lbs/ea
FT2X2X10
2
2
5.9
FT2X4X10
2
4
8.6
FT2X6X10
2
6
10.2
FT2X8X10
2
8
11.8
FT2X12X10
2
12
15
FT2X16X10
2
16
23
FT2X18X10
2
18
25
FT2X20X10
2
20
27
FT2X24X10
2
24
31
FT4x8x10
4
8
16.4
FT4x12x10
4
12
23
FT4x16x10
4
16
27
FT4x18x10
4
18
29.3
FT4x20x10
4
20
31
FT4x24x10
4
24
35
FT4x30x10
4
30
41
FT6x8x10
6
8
23
FT6x12x10
6
12
27
FT6x16x10
6
16
31
FT6x18x10
6
18
33
FT6x20x10
6
20
35
FT6x24x10
6
24
39
Straight sections are stocked in electro-galvanized and BLE (Black Flex-e-coat) finishes. All sizes are nominal.
1.5 inch depth also available. Contact factory for details.
www.flextray.com
5
loadchart
FLEXTRAY PART#
variety of finishes. Stocked in
galvanized and Black painted
Flex-e-coat, Flextray can also be
purchased in any painted color,
hot dip galvanized and stainless
steel.
Electroplated Zinc Galvanizing:
Electrodeposited zinc coating applied to an
average thickness of 0.7 mils (18 microns) to
0.8 mils (20 microns). This surface treatment
is suitable for most indoor applications.
5 FT.
6 FT.
7 FT.
***
8 FT.
9 FT.
10 FT.
FILL AREA
(sq. in.)
Number of
Cables
219
FT1.5x12x10
10
8
6
6
5
5
11.8
FT2x2x10
35
30
25
22
18
15
4.2
78
FT2x4x10
17
17
17
16
15
14
8.2
152
FT2x6x10
18
17
16
14
11
9
12.4
230
FT2x8x10
20
19
17
14
12
9
16.6
308
FT2x12x10
31
28
25
20
16
11
24.8
461
FT2x16x10
39
33
27
24
20
16
33.4
620
FT2x18x10
41
36
31
26
20
15
37.6
698
FT2x20x10
45
39
32
26
20
14
41.8
776
FT2x24x10
FT4x4x10
FT4x8x10
FT4x12x10
FT4x16x10
84
23
35
52
68
72
23
35
52
64
60
20
31
52
60
50
18
27
46
50
39
15
22
38
40
29
11
18
29
31
50.2
15.6
31.6
47.2
63.6
932
290
587
877
1181
FT4x18x10
FT4x20x10
68
67
64
58
54
49
44
39
35
30
26
21
71.6
79.6
1330
1478
FT4x24x10
66
52
38
29
20
11
95.6
1775
6” depth loads available - call us for data.
**Clear Span of Support (Support Points- lbs/ft) ***Fill Rates – Cables used for fill rate testing is .1852 diameter. FLEXTRAY fill capacity
is based on NEC allowable fill of 50%. This rule requires the cable cross-sectional areas added together may not exceed 50% of the tray
area (width x depth = fill area). Fill capacities stated are based on typical Cat5 diameters (.1852 dia.) In real world tray installations,
cables will near completely fill the cable tray when reaching the 50% cable fill (see illustration below). When the tray is full, the total of the
cable area is only 50% of the tray, this is due to empty space between the surface of the cable. Tray Selection is governed by fill rate, not
load. Flextray loads, as shown in chart , will not be exceeded before fill capacity - see illustration
Special sizes also available.
Black FLEX-E-COAT: A 60% gloss with a
film thickness of 0.4-1.2 mils capable of
withstanding a 90 degree angle bend with a
1/4” radius. This finish is compliant with
NFPA 90A, (Plenum Rated), and ASTM B117
for salt spray testing.
fill capacity
GS Pre-Galvanized Finish: Zinc coated
Carbon steel. Pre-galvanized wire before
fabrication. This finish is suitable for most
indoor controlled environments. ASTM A641.
Hot Dip Galvanizing: Provided by
immersing the product in a molten zinc
bath, this coating is applied to an average
thickness of 2.4 mils (60 microns) to 3.2
mils (80 microns). This treatment is most
suitable for outdoor applications or
situations where increased corrosion
resistance is desired.
Stainless: Corrosive resistant Stainless Steel
with no additional surface treatment. This
material option provides the most corrosion
resistant option available. Stainless steel is
used primarily in marine environments or food
processing facilities.
Special Colors (E-Coat painted finishes) are
available upon request.
UL classified sizes
These sizes of Flextray meet UL requirements regarding use as an equipment ground conductor.
FT1.5X12X10
FT2X6X10
FT2X8X10
FT2X10X10
FT2X12X10
FT2X14X10
FT2X16X10
FT2X18X10
FT2X20X10
FT2X22X10
FT2X24X10
FT2X26X10
FT2X28X10
FT2X30X10
FT4X4X10
FT4X6X10
FT4X8X10
FT4X10X10
FT4X12X10
FT4X14X10
FT4X16X10
FT4X18X10
FT4X20X10
FT4X22X10
FT4X24X10
FT4X26X10
FT4X28X10
FT6X8X10
FT6X10X10
FT6X12X10
FT6X14X10
FT6X16X10
FT6X18X10
FT6X20X10
FT6X22X10
FT6X24X10
straight sections
Flextray is available in a wide
fillchart
**
Finishes
6
splice methods
Flextray offers Fast and Secure connections to splice straight runs and radius fittings.
See note
s on pag
e 7 for
Flexmate
UL comp
liance.
Flexmate is the fastest splice method available.
Position connector inside of tool. Squeeze to secure splice.
p/n# FLEXMATE TOOL
p/n# FLEXMATE (50/bx)
HEIGHTS
WIDTHS
2
4
6
2
2
-
4
2
5
5
6
3
-
8
3
6
6
Stocked in electro-galv and
black finishes.
12 16 18 20 24
4
4
4
5
5
6
7
7
7
8
6
7
7
7
8
Chart illustrates number of splice parts RECOMMENDED for each size of FLEXTRAY.
Spring Splice
Spring Splice method enable fast connections of continuous runs.
for
on page 7
See notes L compliance.
eU
Spring Splic
Stocked in electro-galv
and black finishes.
Splice Washers
Washer kits can be used with any application.
UL approved method for splicing cable tray.
p/n# SPRING SPL
(50/BX- includes
installation tool)
1/4"-20 X 1" Carriage
Bolt (FTHDWE 1/4)
WIDTHS
HEIGHTS
2
4
6
2
2
-
4
4
5
-
6
4
-
8
4
6
6
1-3/16" Square Splice
Washer (BTM WASHER)
12 16 18 20 24
4
4
4
5
6
6
7
7
7
8
6
7
7
7
8
1" Square Splice Washer
(TOP WASHER)
1/4 " Serrated Nut
(FTHDWE 1/4)
p/n# WASHER SPL KIT (50/BX)
Assemble with wrench
WIDTHS
HEIGHTS
splice methods
Flexmate System
With two trays end to end, position Spring Splice on the inside of the
tray. Pull assembly tool toward you to tighten. Spring Splice will
automatically lock into place.Repeat on opposite side.
2
4
6
2
2
-
4
2
5
5
6
3
-
8
3
6
6
Stocked in
12 16 18 20 24
4
4
4
5
5
6
7
7
7
8
6
7
7
7
8
electro-galv
and black
finishes.
www.flextray.com
7
Splice Bars
Splice bars are used on side rails only. They add rigidity to washer splice installations. Use on widths greater than 12 inches.
UL approved method for splicing cable tray.
WIDTHS
Stocked in electro-galv
and black finishes.
HEIGHTS
p/n# Splice Bar (50/bx)
2
4
6
12 16 18 20 24
2
2
2
2
2
4
4
4
4
4
4
4
4
4
4
Chart illustrates number of splice parts
RECOMMENDED for each size of FLEXTRAY.
Splice bars require Top Washer and FTHDWE 1/4
to connect. Order 3x’s number of bars needed.
Washer Splice Kit is used for tray bottom splice
splice methods
Assembled Splice
Bar method
attaches between
two side
rails with Top
Washers, nuts
and bolts.
UL Compliance
To meet UL compliance, Tray sizes that meet cross-section area requirements by UL must be spliced using “bolted” connectors. Flextray
petitioned Underwriters Labs for the inclusion of a single bolted connection, in conjunction with our other splicing options that offer much
faster installation options. Flexmate and Spring Splice methods can be used and meet UL requirements by utilizing a bolted splice method on
the bottom of the trays or a single GROUND BOLT.
Ground
Bolt
(p. 15)
Flexmate with Ground Bolt
Spring Splice with Ground Bolt
UL grounding requirements are based on cross sectional areas. When removal of wire, such as when horizontal or vertical fittings are created by cutting and removing
wires from the tray, this area is effected. Separate grounding methods must therefore be used.
8
support methods
ceiling types
support methods ceiling types
Trapeze Support
p/n#TRAPEZE SUPT2 (50/BX)
After cable is loaded snap in plastic retainer to lock support to tray. Accepts
1/4” & 3/8” threaded rod sizes.
Center Hangers
NEW!
p/n#
4 CTR HGR
6 CTR HGR
8 CTR HGR
12 CTR HGR
16 CTR HGR
18 CTR HGR
20 CTR HGR
24 CTR HGR
Position hanger below tray.
Lock hanger into place by twisting hanger where tabs are over tray cross
wire. Tabs can be bent over wire if needed.
Center Hung Clips
p/n# CTR HUNG CLP (50/BX)
Use Clips for 4” - 8” widths. Accepts 1/4” threaded rod.
www.flextray.com
9
support methods
2” Center Supports
p/n# 2 IN CTR SUPT (50/BX)
C Brackets
NEW!
improved hold-down tab
C Bracket attached to strut or other ceiling type
p/n# 4 C BRKT
8 C BRKT
12 C BRKT
Combination L and C bracket for layered runs of tray.
Profile
*All items on these
pages are available
from stock in
electro-galv or BLEBlack finish. Add BLE
to suffix of part
p/n# 10 LFT PROFILE
number for black.
Use as a trapeze support for wider runs of tray.
ceiling types
Assemble with ATTACHMENT CLIP (P. 11). Accepts 1/4” threaded rod.
10
wall types
support methods wall types
Shelf Brackets
support methods
NEW!
p/n#
6 SHELF BRKT
8 SHELF BRKT
12 SHELF BRKT
16 SHELF BRK
18 SHELF BRKT
20 SHELF BRKT
24 SHELF BRKT
Shelf Brackets offer heavy duty support.
Conduit sizes from 1/4” - 1 1/2” can be supported through shelf brackets.
L Brackets
NEW!
improved hold-down tab
p/n#
4 L BRKT
8 L BRKT
12 L BRKT
16 L BRKT
20 L BRKT
24 L BRKT
Use L BRKT
with
PEDESTAL
CLAMP
Hold down tray with tab or with TOOLLESS CLIP
Z Brackets
p/n# Z BRKT
Use as a vertical support
Use Z BRKT to lift tray off floor
www.flextray.com
11
support methods
Attachment Clip
wall types
p/n# Attachment Clip (50/bx)
Use with 2 IN CTR SUPT (p. 9)
Wall support for 2” wide tray
Support Washer
p/n#SUPT WASHER (50/BX)
Use as a hold down
Use as center hanger with threaded rod
Wall Support
p/n# WALL SUPT
Use as center hanger with threaded rod
Mount to metal framing for vertical support
support methods
underfloor types
12
support methods underfloor types
Pedestal Clamps
NEW!
Use with Shelf BRKT
p/n# PEDESTAL CLAMP
Use with L BRKT
Pedestal Kit
Floor Pan
p/n# FLOOR PAN 4
FLOOR PAN 6
p/n#
PEDESTAL KIT
(2 EA PEDESTAL
CLAMPS & 1 EA
24” PROFILE,
NUTS & BOLTS
FOR HOLD DOWN)
Available in 18” width.
Other heights available.
Pedestal Kits provide full
24” support for underfloor
applications.
Support Flextray independent of other infrastructure.
www.flextray.com
13
accessories
Straight run drop-out
Drop-Outs
accessories
p/n#
4 IN DROP-OUT
6 IN DROP-OUT
Drop Out cable from
sides of tray
Rack Clamp
Toolless Connectors
p/n# TOOLLESS CLIP (50/BX)
p/n# RACK CLAMP BLE (4/BX)
Snap in locking
pin secures the
tray to support
Installs without drilling into rack
Use TOOLLESS
CLIP to hold
down tray to
supports
14
accessories
Dividers
accessories
Attach Divider with
WASHER SPL KIT (p. 6)
p/n#
2 IN DIVIDER
4 IN DIVIDER
6 IN DIVIDER
Covers
p/n#
2 IN COVER
4 IN COVER
6 IN COVER
8 IN COVER
12 IN COVER
16 IN COVER
18 IN COVER
20 IN COVER
24 IN COVER
Bend down tabs to secure covers to tray
Solid Bottom Inserts
p/n#
INSERT 2X118
INSERT 4X118
INSERT 6X118
INSERT 8X118
INSERT 12X118
INSERT 16X118
INSERT 18X118
INSERT 20X118
INSERT 24X118
*All items on this
page are available
from stock in
electro-galv or BLEBlack finish. Add
BLE to suffix of part
Use inserts for solid surface needs.
number for black.
www.flextray.com
15
Conduit Fittings
NEW!
Ground Bolts
Allows smooth transition from tray to conduit
Assembles easily
Ground Wire Supports
p/n# GROUND SUPT GL
(100/BX)
p/n# GROUND BOLT
Use GROUND BOLT with Spring Splice or
Flexmate to meet UL requirements –
see page 7
Supports ground wire along side of trays
accessories
p/n#
fits conduit size
FTEMTDO50
1/2”
FTEMTDO75
3/4”
FTEMTDO100
1”
FTEMTDO125
1 1/4”
(comes unassembled) (4/BX)
16
hardware
Bottom Mounted Installation
hardware
Ceiling Anchors
Ceiling Rod Anchors allow fast & easy installation of threaded rods to most ceiling types. Anchors for wood, steel or
concrete ceilings utilizing 3/8” threaded rods are available. Side or Bottom mounting types makes it convenient for
space sensitive installations. 1/4“ and 3/8” rod sizes are available – call factory for price and availability
CEILING TYPES
WOOD . . . . . . . .
WOOD . . . . . . . .
WOOD . . . . . . . .
WOOD . . . . . . . .
STEEL . . . . . . . .
STEEL . . . . . . . .
STEEL . . . . . . . .
STEEL . . . . . . . .
STEEL . . . . . . . .
CONCRETE . . . . . .
(anchors come 50/bx)
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
P/N#
FT3820WDB
FT3820WDS
FT3830WDB
FT38075WDB
FT38125STS
FT3820STB
FT38075STB
FT38125STB
FT3810STB
FT3820CTB
Side Mounted Installation
SIZE/DESCRIPTION
3/8”X2” BOTTOM MOUNT
3/8”X2” SIDE MOUNT
3/8”X3” BOTTOM MOUNT
3/8 X.75” BOTTOM MOUNT
3/8 X 1.25 SIDE MOUNT
3/8 X 2 BOTTOM MOUNT
3/8 X .75 BOTTOM MOUNT
3/8 X1.25 BOTTOM MOUNT W/NUT
3/8 X 1 BOTTOM MOUNT W/NUT
3/8X2 BOTTOM MOUNT
Concrete Installation
Extension Pole Tool
Eliminate the hassle of building scaffolding or lifts to install your threaded rod
TO INSTALL...
1. Cut rod to length, screw ceiling anchor onto rod, and insert rod into pole.
2. In vertical position with drill on working end of pole, center screw on
members to be penetrated and begin installation. When drill lags down,
check to see if installation is complete. Do not overtorque screw.
Pull down on pole and the rod will remain ready to receive your FLEXTRAY
Support selection.
TOOLS
P/N#
FTSIDE
FTBTM
FTPOLE
DESCRIPTION
NUT DRIVER FOR SIDE MOUNTING ANCHORS
NUT DRIVER FOR BOTTOM MOUNTING
EXTENSION POLE TOOL
www.flextray.com
17
Threaded Rod/Beam Clamps/Hardware
Threaded Rod
Coupling Nuts
Hex Nuts
p/n#
FT1905
FT1906
FT1907
FT1908
FT1909
FT1910
FT1911
FT1912
FT1913
p/n#
FT1859
FT1860
FT1861
(50/BX)
p/n#
FT1842
FT1843
FT1844
FT1845
(100/BX)
size
1/4”-20
3/8”-16
1/2”-13
Lock Washers
Finned Nuts
p/n#
FINNED NUT 1/4
FINNED NUT 3/8
(100/BX)
size
1/4”-20
5/16”-18
3/8”-16
1/2”-13
p/n#
FT1881
FT1883
FT1884
(200/BX)
size
1/4”-20
3/8-16
size
1/4”
3/8”
1/2”
Beam Clamp
Flat Washers
Square Washers
p/n#
FT6500
FT6502
FT6503
p/n#
FT1874
FT1876
FT1877
(200/BX)
p/n#
FT2003
FT2004
FT2005
(50/BX)
size
1/4”
3/8”
1/2”
C Clamp
p/n#
FT6053
FT6054
size
3/8”
1/2”
size
1/4”
3/8”
1/2”
Swivel Rod Hanger
U Bolt Clamp
p/n#
size
FT6061
1/2”
p/n#
FT6030
Spring Nuts
Channel Framing
p/n#
FT5812SL
FT5812SH
FT1315SL
FT1315SH
1-5/8"
p/n#
FT1032 SW
FT1034 SW
FT1035 SW
(100/BX)
size
1 5/8”X1 5/8” SL – 12 GAUGE – 10’ LENGTHS
1 5/8”x1 5/8”SH – 12 GAUGE – 10’ LENGTHS
13/15”x1 5/8”SL – 15 GAUGE – 10’ LENGTHS
13/15”X1 5/8”SH – 15 GAUGE – 10’ LENGTHS
13/16"
1-5/8"
1-5/8"
size
5/16”
3/8”
1/2”
size
1/4”-20
3/8”-16
1/2”-13
hole style
SL
hole style
SH
Channel framing also available in special pre-cut lengths and colors.
hardware
sizes
1/4”-20 X 6’
1/4”-20 X 10’
1/4”-20 X 12’
3/8”-16 X 6’
3/8”-16 X 10’
3/8”-16 X 12’
1/2”-13 X 6’
1/2”-13 X 10’
1/2”-13 x 12’
18
Flexpack
Convenient pre-packaged Flextray system includes 4 straight sections and hardware for closet or small installations.
All sizes contain 7’ lengths that can be shipped FEDX or UPS quickly.
p/n#
FP2X8X7
FP2X12X7
FP4X12X7
Size
2” H X 8”W
2”H X 12”W
4”H X 12”W
*Also available in Black (BLE) finish
Rackpack
Rackpack offer items you
NEW!
P/N#
RP4X12 BLE
RP6x12 BLE
SIZE
4”H X 12”W
6”H x 12”W
need to organize pathways
into racks and closet spaces.
Each pack includes one 4’7”
(nom.) section of tray, two
RACK CLAMPS and one Z BRKT
all in the Black (BLE) Finish.
Try the convenience of prepackaged, easy to ship
Flextray all-inclusive system.
www.flextray.com
19
RF raised floor system NEW!
Self Supporting – Patented vertical support that does not
compromise raised floor support weight limitations or warranties.
No Stringer Types to Consider – RF System is not suspended
from tile stringers – it is independently supported. Meaning no
variables or regulations to consider.
UL Classified – All sizes of RF System trays are now UL Listed
when connected with ground clip (see page 21).
(patent pending)
Easy Drop-In Design – RF components are designed to fit 24”
Raised Floor designs – just drop through tile space and lock into
place – no fastening required. No cutting or splicing needed.
Add More RF Easily – Additional runs and layers of RF can be
easily added or changed without waste, demolition or lost time.
Multiple Tray Sizes – 24, 12 and 6 inch standard sizes.
Others available upon request.
Computer Centers
The RF System’s modular design adapts easily for use
with any cabling application.
Switch Rooms
The New RF System gives you the flexibility you’ve come to expect from Flextray products. This patented design is
self-supporting – meaning no floor stringer or stanchion variables to consider. The ease of installation and RF’s
design will allow you to re-configure your cable pathways for future expansion. Install vertical supports and lock
the horizontal bar into position. You are ready to lay in the tray sections and go.
Install Vertical
Support Legs
Lock on the Horizontal Support Bar
Drop in Tray Panels
FLEXTRAY’S RF System
provides maximum accessibility
and flexibility for your raised
floor cabling needs:
20
RF components
Flextray’s RF System uses 24’ centered floor support design. This configuration will allow easy retrofit capabilities without
compromising the access floor installation. Tray sizes offered will fit into this configuration.
Components needed to complete your job are simple…
Vertical Supports (patented)
RF’s vertical supports independently support cable tray without compromising raised access floor
weight limitations or warranties. Vertical supports are offered in a side variety of heights.
Part number:
FTRF 2” Vertical Support - 2” Vertical Support
(special sizes also available)
Installs independently of Raised Floor System.
Horizontal Support Bars
Horizontal Supports have simple lock-in design to fit tray
widths. Snap into vertical supports - then install tray - no
fastening needed.
Part number:
FTRF 6” Horizontal Support - 6” Horizontal Support
www.flextray.com
21
Trays come in 6”, 12” and 24” widths, in depths of 2”, 4” and 6” and lengths of 2’
and 4’ to fit through floor areas easily.
Part number:
FTRF 2X6X2 Tray Section 2 inch deep, 6 inch wide, 2 feet long
Horizontal Fitting Flat
Multi-Level Bracket
This tray allows easy transition through T’s, elbows and
crosses in your pathway.
Use brackets to achieve
multi-level pathways.
p/n #
FTRF 0x24x2
FTRF12CBRKT
FTRF6BRKT
FTRFLBRKT
Ground Clip
Vertical Clip
UL approved connector. Use for additional hold down to
Horizontal Supports and C Brkts for Multi-tier runs.
Locks vertical support around stanchion.
p/n #
FTRF GROUND CLIP
p/n #
VERTICAL CLIP
Trays
22
RF accessories
Cable Roller
Flextray’s new Cable Roller maintains recommended cable radius in bends and turns.
p/n# CABLE ROLLER
label clip
Label Clips enable wiring identification.
p/n# LABEL CLIP (10/BX)
Use as horizontal radius protection.
www.flextray.com
23
cutting tools
CleanShear ®
Cut, Bend, Install…..Flextray can be formed into any pathway configuration by simply cutting and bending straight
sections. Cleanshear is the only tool that eliminates sharp edges that could damage you or your cable installation.
BAD
Correct cut made with a
CLEANSHEAR Cutter.
patented
Incorrect cut made with
standard bolt cutter.
Offset bolt cutters
leave sharp edges.
p/n# CLEANSHEAR
How To Cut Flextray
STEP 1 With tray facing up,
position bolt cutter in the middle
of a section.
STEP 2 Slide bolt cutter to
the right flush against the vertical
wire at a 45˚ angle.
STEP 3 Cut wire.
STEP 4 Turn tray up, with open
side facing you. Repeat steps 1
and 2.
STEP 5 Face tray, open side down,
and repeat steps 1 and 2 until all
wires are cut on this side.
STEP 6 Approach tray from
opposite side and repeat steps 1-5
to cut wires on other side.
CleanShear ® Bender – With Bending Attachment
Cleanshear can be purchased with our exclusive bending attachment. It makes bending larger sized of tray easy.
patented
p/n# CLEANSHEAR BEND
How To
Bend
Flextray
STEP 1 Position bending tool between sections on the side
wires with handles apart.
STEP 2 Push handles together to bring tray together. Secure
with hardware.
cutting tools
GOOD
24
cutting tools
AirShear
Flextray offers the fastest cutting tool available. The patented Cleanshear cutting heads along
cutting tools
with effort free cutting make Flextray the fastest- safest pathway option to install.
NEW!
patented
p/n#AIRSHEAR
• TIME SAVINGS WITH AIRSHEAR 56.8%
Cutting Method Tray Size
CLEANSHEAR
FT2 X 24
AIRSHEAR
FT2 X 24
Configuration Time
1 minute 58 seconds
58 seconds
Airshear operatate neumatically. 90 lbs PSI is required. 1/4” fitting.
Cutting with
Airshear makes
installation fast
www.flextray.com
25
creating fittings
Making Horizontal Bends
FLEXTRAY can be cut and formed on-site into nearly any configuration by cutting the bottom and side wires of the straight
illustrate just a few suggested methods for creating bends. Please refer to your cable manufacturer’s suggested bend radius when
forming FLEXTRAY.
STEP 1 Position bending tool
between sections on the side wires
with handles apart.
To create bends, simply remove sections of FLEXTRAY. For long radius bends, remove every other section. For short radius bends,
remove one section and both side rails.
STEP 2 Push handles together to bring
tray together. Secure with hardware.
Bends can be connected using FLEXMATE Connectors or Splice Washers, nuts and bolts.
creating fittings
sections. After removing the cut wires, a radius can be bent and fastened with appropriate hardware. The following pages
26
creating fittings
creating fittings
Creating Horizontal Radius Bends
1 Connector
Using the CLEANSHEAR Cutter, cut out sections.
Using the CLEANSHEAR Bender pull sections together. FLEXMATE
Connectors make it easy.
Cut out one center section of 4" tray and
one side rail both directions.
Simply bend and attach with Top and Bottom
Washers, nuts and bolts.
Cut out two sections of larger sizes of FLEXTRAY and three side rail
sections, both directions.
Simply bend and attach with Top and Bottom
Washers, nuts and bolts.
1 Bolt
BOTTOM WASHER
TOP WASHER
1 Nut
1 Bolt
2 SUPPORT
WASHERS
1 Nut
www.flextray.com
27
Creating Two-Piece Radius Bends
This tight radius
creating fittings
style bend is
accomplished by
cutting FLEXTRAY
and assembling
using hardware
shown.
Remove two side rail sections.
Overlap pieces and attach with two Washer Splice Kits. Smaller
sizes may require only one set.
Remove side rail sections.
For larger sizes, use two Support Washers.
Remove two side rail sections.
Overlap pieces and attach with four FLEXMATE Connectors. Smaller
sizes may require only two.
28
creating fittings
Making Tees
creating fittings
The flexibility of FLEXTRAY enables tees and
intersections to be placed anywhere along the run at
any time. Simply cut, bend and connect.
Cut out side rail of main run according to width of the intersecting tee.
Remove sections on both sides of the intersecting run.
Bend the side rails out of both runs and connect to intersecting run
with Splice Washers, nuts and bolts.
Alternate wide radius 2" to 8".
p/n#
90 DEGREE BAR
Short radius 4" to 12" tee attached with 90 Degree Splice Bar.
Wide radius 12" to 20" tee.
www.flextray.com
29
Making Crosses
Wide radius 12" to 20" tee.
Reducing Sizes of Trays
Reducing 12" to 8".
Use 3 sets of Top and Bottom Washers, nuts and bolts to splice.
Creating “Y” Fittings
Attach pieces with Splice Washers, nuts and bolts.
Remove side wires from main tray (1). Remove bottom wires at angles on attachment tray (2).
creating fittings
Short radius 4" to 12" cross attached with 90 Degree Splice Bar.
30
creating fittings
Making Vertical Fittings
creating fittings
Avoid any obstacles. It is easy with FLEXTRAY. Simply cut the side wires and bend.
Simply cut side wires and bend.
Alternate cuts allow a variety of vertical drops and rises. Whatever the obstacle.
www.flextray.com
31
Tools Available for Architects, Consultants and Engineers
Flextray offers information that will help you plan and design pathway applications. Our easy to use software and
Technical Binder contain all the information you’ll need to complete your design. Call us at 1-888-353-9879 or email
flextray@gsmetals.com to select your free tools today.
Flextray offers answers to pathway questions. Ask for our Technical
Updates today. We’ll keep you informed.
www.flextray.com
NEW!
Our Website offers quick
reference to all your
Flextray questions. Use
our product configurator
to choose the materials
you’ll need. Load/Fill
rates and CSI
specification are ready
when you need them.
32
CSI Specification Form
Use this form to create the pathway specification you need. You can create your specification from our Selector
Software CD or go to our website www.flextray.com. Pick the options you want to use in your specification.
MANUFACTURER
PRODUCT NAME
❑ FLEXTRAY® Cable Management System
❑ FLEXTRAY Cable Managment System, or approved equal.
❑ Approved Flexible site configurable wire mesh basket tray. Approved manufacturers are:
❑ Approved flexible site configurable wire mesh basket tray, 5mm minimum wire gauge
MANUFACTURER
❑ GS Metals Corp. 3764 Longspur Road Pinckneyville, IL 62274, Phone: (888) 353-9879,
Fax: (618) 357-8486, Website: www.FLEXTRAY.com, Email: flextray@gsmetals.com
❑ Approved Supplier
❑ Manufacturer must have US production facilities; tray must be produced and finished in
United States with full domestic content.
❑ Product must be manufactured in unionized production facility by union workers.
❑ Manufacturer must have a demonstrated history of production and distribution of product
offering for a minimum period of 3 years in the US.
❑ Tray specified shall be UL classified and listed.
❑ Tray specified shall have T-weld on top rail (all sizes of tray) in order to avoid sharp
surfaces or protrusions on tray surface.
❑ Company shall be ISO 9001 Certified.
CABLE MANAGEMENT SYSTEM
PRODUCT DESCRIPTION
FLEXTRAY is a welded wire mesh cable management system. The open mesh permits easy
access to the tray and provides continuous ventilation of cables installed in the tray. A
continuous ground conductor fixing system can be accomplished by the use of approved
splices and bonding jumpers.
GS Metals 'Flextray' continuous rigid welded steel wire mesh cable management system.
1. Continuous safety edge wire welded to top of tray.
2. Wire mesh welded at all intersections.
UL CLASSIFICATION
Straight sections 1.5x12, 2x6,2x8,2x12,2x16,2x18,2x20,2x24,4x4,4x8,4x12,4x16,
4x18,4x20 and 4x24 UL Classified.
COMPOSITION & MATERIALS
FLEXTRAY is produced from high mechanical strength steel wire, which is first welded into a
net, then formed into channels to carry the cables. Covers and inserts are made from pregalvanized steel are available to protect cables. They are easily installed and can be easily
lifted for maintenance activities. Splicing options in five styles made of electro galvanized
steel effectively connects trays end to end. Material Carbon steel wire, ASTM A 510, Grade
1008. Wire welded bent and surface treated after manufacturer. Stainless steel wire AISI
316L, 2B, finished cold drawn wire.
APPROVED TRAY
❑ FT1.5X4X10
❑ FT2X2X10
❑ FT2X12X10
❑ FT2X24X10
❑ FT2X34X10
❑ FT4X16X10
❑ FT4X26X10
❑ FT6X16X10
❑
❑
❑
❑
❑
❑
❑
❑
FT1.5X6X10
FT2X4X10
FT2X16X10
FT2X26X10
FT4X4X10
FT4X18X10
FT4X30X10
FT6X20X10
❑
❑
❑
❑
❑
❑
❑
❑
FT1.5X8X10
FT2X6X10
FT2X18X10
FT2X30X10
FT4X8X10
FT4X20X10
FT6X8X10
FT6X24X10
❑
❑
❑
❑
❑
❑
❑
❑
FT1.5X12X10
FT2X8X10
FT2X20X10
FT2X32X10
FT4X12X10
FT4X24X10
FT6X12X10
FT6X26X10
TO DENOTE BLACK FINISH, ADD BLE TO THE PART NUMBER
Standard sizes - Mesh size is 2" x 4" (50 x 100 mm). The standard tray length is 118" (3 m)
supplied in four channel depths, 1 1/2", 2", 4" and 6" (38, 54, 105 and 159 mm). Thirteen
widths offered include 2", 4", 6", 8", 12" 16", 18", 20", 24", 26", 30", 32" and 34". (50,100,
150, 200, 300, 400 450, 500, 600, 650, 759, 800 and 850 mm).
Special size - Custom sizes are available on request.
Wire Diameter - A minimum of 0.197" on all mesh sections.
FINISHES
Finish options include:
❑ Electroplated Zinc Galvanizing (Standard Stock Finish) - Electrodeposited zinc coating
applied to an average thickness of 0.7 mils (18 microns) to 0.8 mils (20 microns). This
surface treatment is suitable for most indoor applications and may be used outdoors in
mild environments only.
❑ Hot Dip Galvanizing - Provided by immersing the product in a molten zinc bath, this
coating is applied to an average thickness of 2.4 mils (60 microns) to 3.2 mils (80
microns). This treatment is most suitable for outdoor applications or situations where
increased corrosion resistance is desired.
❑ Epoxy Powder Coat Paint - Powder painted surface treatment using ASA 61. This finish
option provides an aesthetically pleasing durable coating ideal for use in office buildings
and various other indoor applications. Powder Coat colors are available on special
request.
❑ Stainless Steel - Corrosive resistant AISI 316L Stainless Steel with no additional surface
treatment. This material option provides the most corrosion resistant option available.
Stainless steel is used primarily in marine environments or food processing facilities.
LIMITATIONS
See page 13 for capacities of various FLEXTRAY widths at different spans, or consult the
software in the FLEXTRAY CD.
TECHNICAL DATA
APPLICABLE STANDARDS American Iron and Steel Institute (AISI)/American Society for Testing
and Materials (ASTM)
ASTM A123 - Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products
ASTM A510 - General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel
ASTM A569 - Steel, Carbon (0.15 Maximum, Percent), Hot-Rolled Sheet and Strip
Commercial Quality
www.flextray.com
33
ASTM A570 - Standard Specification for Steel, Sheet and Strip, Carbon, Hot- Rolled,
Structural Quality
ASTM A653/A653M - Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) or
Zinc-Iron Alloyed-Coated (Galvanized) by the Hot-Dip Process
ASTM B633 - Electrodeposited Coatings of Zinc on Iron and Steel
National Uniform Seismic Installation Guide (NUSIG)
AVAILABILITY
Available nationwide from manufacturer's authorized representatives.
APPROVALS
FLEXTRAY meets applicable Underwriters Laboratories standards and requirements. Contact GS
Metals for detailed UL classification information.
WARRANTY
Limited 3 year. Lifetime on materials and workmanship if Installed by a FLEXTRAY Certified
Contractor.
EXAMINATION
MAINTENANCE
None required.
INSTALLATION
METHODS
FLEXTRAY can be fashioned on the job site by simply cutting the steel wires. The exclusive use
of CleanShear cutters, NOT standard bolt cutters with an offset cutting blade jaw, is recommended to ensure a safe and finished edge entraining of a protective coat over cuts and creation of a galvanic couple to protect them.
Install and support cable management system in accordance with span load criteria of L/240.
PRECAUTIONS
For Carbon Steel FLEXTRAY to be used as an equipment ground conductor, certain splicing
methods must be used. Contact GS Metals for more information.
Install cable management system using hardware, splice connectors, support components and
accessories furnished by manufacturer.
TECHNICAL SERVICES
A free video/CD is available. Layout drawings and details in AutoCAD are provided upon
request. Flextray offers its Configurator and FlexDraw software for determining requirements
for Flextray. GS Metals Flextray representatives will assist with technical questions, provide
assistance in determining bill of materials, and in installation management and training.
SPEC-DATA® and MANU-SPEC® are registered trademarks of The Construction Specifications
Institute. The ten-part SPEC-DATA format conforms to the editorial style of The Construction
Specifications Institute and is used with their permission. The manufacturer is responsible for
technical accuracy.
Filing Systems
Architects' First Source for Products
MANU-SPEC®
Sweet's Catalog Files
Additional product information is available from the manufacturer.
product index
12 C Brkt . . . . . . . . . . . . . . . . . 9
12 CTR HGR . . . . . . . . . . . . . . . 8
12 L Brkt . . . . . . . . . . . . . . . . 10
12 Shelf Brkt . . . . . . . . . . . . . 10
16 CTR HGR . . . . . . . . . . . . . . . 8
16 L Brkt . . . . . . . . . . . . . . . . 10
16 Shelf Brkt . . . . . . . . . . . . . 10
18 CTR HGR . . . . . . . . . . . . . . . 8
18 Shelf Brkt . . . . . . . . . . . . . 10
20 CTR HGR . . . . . . . . . . . . . . . 8
20 L Brkt . . . . . . . . . . . . . . . . 10
20 Shelf Brkt . . . . . . . . . . . . . 10
24 CTR HGR . . . . . . . . . . . . . . . 8
24 L Brkt . . . . . . . . . . . . . . . . 10
24 Shelf Brkt . . . . . . . . . . . . . 10
4 C Brkt. . . . . . . . . . . . . . . . . . 9
4 CTR HGR . . . . . . . . . . . . . . . . 8
4 L Brkt . . . . . . . . . . . . . . . . . 10
4 Shelf Brkt . . . . . . . . . . . . . . 10
6 CTR HGR . . . . . . . . . . . . . . . . 8
8 C Brkt. . . . . . . . . . . . . . . . . . 9
8 CTR HGR . . . . . . . . . . . . . . . . 8
8 L Brkt . . . . . . . . . . . . . . . . . 10
8 Shelf Brkt . . . . . . . . . . . . . . 10
FT38075STB . . . . . . . . . . . . . . 16
FT38075WDB . . . . . . . . . . . . . 16
FT3810STB. . . . . . . . . . . . . . . 16
FT38125STB . . . . . . . . . . . . . . 16
FT38125STS . . . . . . . . . . . . . . 16
FT3820CTB. . . . . . . . . . . . . . . 16
FT3820STC . . . . . . . . . . . . . . . 16
FT3820WDB . . . . . . . . . . . . . . 16
FT3820WDS . . . . . . . . . . . . . . 16
FT3830WDB . . . . . . . . . . . . . . 16
FTBTM -btm mount nut drive . . 16
FTPOLE - extension Pole . . . . . 16
FTSIDE- side mount nut driver . 16
Pedestal Clamp . . . . . . . . . . . . 12
Pedestal Clamp kit . . . . . . . . . 12
12 in Cover . . . . . . . . . . . . . . 14
16 in Cover . . . . . . . . . . . . . . 14
18 in Cover . . . . . . . . . . . . . . 14
2 in Cover . . . . . . . . . . . . . . . 14
2 in Ctr Supt. . . . . . . . . . . . . . . 9
2 in Divider . . . . . . . . . . . . . . 14
20 in Cover . . . . . . . . . . . . . . 14
24 in Cover . . . . . . . . . . . . . . 14
4 in Cover . . . . . . . . . . . . . . . 14
4 in Divider . . . . . . . . . . . . . . 14
4 in Drop-Out . . . . . . . . . . . . . 13
6 in Cover . . . . . . . . . . . . . . . 14
6 in Drop-Out . . . . . . . . . . . . . 13
8 in Cover . . . . . . . . . . . . . . . 14
Airshear. . . . . . . . . . . . . . . . . 24
Attachment Clip . . . . . . . . . . . 11
Beam Clamps . . . . . . . . . . . . . 17
Btm Washer . . . . . . . . . . . . . . . 6
C Brackets . . . . . . . . . . . . . . . . 9
Cable Roller . . . . . . . . . . . . . . 22
Ceiling and Plenum Spaces. . . . . 2
Ceiling Rod Anchors. . . . . . . . . 16
Center Hangers. . . . . . . . . . . . . 8
Cleanshear . . . . . . . . . . . . . . . 23
Cleanshear Bend. . . . . . . . . . . 23
Coil Splice . . . . . . . . . . . . . . . . 7
Coil Spring Splice . . . . . . . . . . . 7
Conduit Clamps. . . . . . . . . . . . 15
Coupling Nuts . . . . . . . . . . . . . 17
Covers . . . . . . . . . . . . . . . . . . 14
Creating Fittings- Vertical . . . . . 30
Creating Fittings-"Y" . . . . . . . . 29
Creating fittings-Crosses. . . . . . 29
Creating Fittings-Horizontal . . . 25
Creating FittingsReducing sizes . . . . . . . . . . . 29
Creating fittings-Tees . . . . . . . . 28
Creating Fittingstwo piece horizontal. . . . . . . 27
Ctr Hung Supt. . . . . . . . . . . . . . 8
Design Tools . . . . . . . . . . . . . . 31
Dividers . . . . . . . . . . . . . . . . . 14
Drop-Outs . . . . . . . . . . . . . . . 13
Fill Rates . . . . . . . . . . . . . . . . . 5
Flat Washers. . . . . . . . . . . . . . 17
Flexmate System . . . . . . . . . . . 6
Flexmate Tool. . . . . . . . . . . . . . 6
Flexmate2 . . . . . . . . . . . . . . . . 6
FlexPack . . . . . . . . . . . . . . . . 18
Flextray Convenience Kits . . . . 18
Floor Pan 4 . . . . . . . . . . . . . . 12
Floor Pan 6 . . . . . . . . . . . . . . 12
FT1032SW . . . . . . . . . . . . . . . 17
FT1034SW . . . . . . . . . . . . . . . 17
FT1035SW . . . . . . . . . . . . . . . 17
FT1315SH . . . . . . . . . . . . . . . 17
FT1315SL. . . . . . . . . . . . . . . . 17
FT1842 . . . . . . . . . . . . . . . . . 17
FT1843 . . . . . . . . . . . . . . . . . 17
FT1844 . . . . . . . . . . . . . . . . . 17
FT1845 . . . . . . . . . . . . . . . . . 17
FT1859 . . . . . . . . . . . . . . . . . 17
FT1860 . . . . . . . . . . . . . . . . . 17
FT1861 . . . . . . . . . . . . . . . . . 17
FT1874 . . . . . . . . . . . . . . . . . 17
FT1876 . . . . . . . . . . . . . . . . . 17
FT1877 . . . . . . . . . . . . . . . . . 17
FT1881 . . . . . . . . . . . . . . . . . 17
FT1883 . . . . . . . . . . . . . . . . . 17
FT1884 . . . . . . . . . . . . . . . . . 17
FT1905 . . . . . . . . . . . . . . . . . 17
FT1906 . . . . . . . . . . . . . . . . . 17
FT1907 . . . . . . . . . . . . . . . . . 17
FT1908 . . . . . . . . . . . . . . . . . 17
FT1909 . . . . . . . . . . . . . . . . . 17
FT1910 . . . . . . . . . . . . . . . . . 17
FT1911 . . . . . . . . . . . . . . . . . 17
FT1912 . . . . . . . . . . . . . . . . . 17
FT1913 . . . . . . . . . . . . . . . . . 17
FT2003 . . . . . . . . . . . . . . . . . 17
FT2004 . . . . . . . . . . . . . . . . . 17
FT2005 . . . . . . . . . . . . . . . . . 17
FT5812SH . . . . . . . . . . . . . . . 17
FT5812SL. . . . . . . . . . . . . . . . 17
FT6030 -UBOLT CLAMP . . . . . . 17
FT6053 . . . . . . . . . . . . . . . . . 17
FT6054 . . . . . . . . . . . . . . . . . 17
FT6500 . . . . . . . . . . . . . . . . . 17
FT6502 . . . . . . . . . . . . . . . . . 17
FT6503 . . . . . . . . . . . . . . . . . 17
FTEMTDO075 . . . . . . . . . . . . . 15
FTEMTDO100 . . . . . . . . . . . . . 15
FTEMTDO125 . . . . . . . . . . . . . 15
FTEMTDO50 . . . . . . . . . . . . . . 15
Fthdwe 1/4 . . . . . . . . . . . . . . . 6
Ground Bolt . . . . . . . . . . . . . . 15
Ground Supt GL . . . . . . . . . . . 15
Hex Nuts:. . . . . . . . . . . . . . . . 17
insert 12x118 . . . . . . . . . . . . 14
insert 16x118 . . . . . . . . . . . . 14
insert 18x118 . . . . . . . . . . . . 14
insert 20x118 . . . . . . . . . . . . 14
insert 24x118 . . . . . . . . . . . . 14
insert 2x118 . . . . . . . . . . . . . 14
insert 4x118 . . . . . . . . . . . . . 14
insert 6x118 . . . . . . . . . . . . . 14
insert 8x118 . . . . . . . . . . . . . 14
L Brackets . . . . . . . . . . . . . . . 10
Label Clip. . . . . . . . . . . . . . . . 22
Load Tables . . . . . . . . . . . . . . . 5
Lock Washers . . . . . . . . . . . . . 17
Metal Framing . . . . . . . . . . . . 17
RF Components. . . . . . . . . . . . 20
RF System . . . . . . . . . . . . . . . 19
Rack Clamp . . . . . . . . . . . . . . 13
RackPack . . . . . . . . . . . . . . . . 18
Raised Access Floors . . . . . . . . . 3
Shelf Brackets. . . . . . . . . . . . . 10
Solid Bottom Inserts . . . . . . . . 14
Specification . . . . . . . . . . . . . . 32
Splice Bar. . . . . . . . . . . . . . . . . 7
Splice Methods . . . . . . . . . . . . . 6
Spring Nuts . . . . . . . . . . . . . . 17
Spring Splice . . . . . . . . . . . . . . 6
Square Washers . . . . . . . . . . . 17
Straight Sections . . . . . . . . . . . . 4
Support Methods. . . . . . . . . . . . 8
Supt Washer . . . . . . . . . . . . . . 11
Telecommunication Closets . . . . . 3
Threaded Rod . . . . . . . . . . . . . 17
Toolless Clip . . . . . . . . . . . . . . 13
Top Washer . . . . . . . . . . . . . . . 6
Trapeze Supt . . . . . . . . . . . . . . 8
UL Classified Sizes. . . . . . . . . . . 5
Wall Support. . . . . . . . . . . . . . 11
Wall Supports . . . . . . . . . . . . . 10
Washer Splice Kit . . . . . . . . . . . 6
Where to Use Flextray. . . . . . . . 2
Z Bracket . . . . . . . . . . . . . . . . 10
product index
Inspect areas to receive cable management system. Notify the Engineer of conditions that
would adversely affect the installation or subsequent utilization of the system. DO not proceed
with the installation until the unsatisfactory conditions are corrected.
COST
Product is priced per unit and may depend on quantities ordered. Many parts come in bags of
50. Installation cost may be affected by substrate fastening requirements. Local distributor
will quote actual materials price. Refer to FLEXTRAY pricing guide for budgetary pricing.
3764 Longspur Road • Pinckneyville, IL 62274
618-357-5353 • 888-353-9879 • 618-357-3605 fax
www.flextray.com
705-05

Flextray NEW Catalog 02/04 Q

Transcription

Similar documents

christmas brochure

Party Trays Relax. Eat. Enjoy.

MARQ Comparison Sheet - Marq Packaging Systems

information flyer - Penwell

introducing empress food trays!

Whitening Instructions - Michigan Beautiful Smiles

Oven Ready Food Trays

Carrello Multiservice Multi-service trolleys Chariots à

milk crate - Melmat, Inc.

Tutorial