F3xDGA Instalation instruction
Transcription
F3xDGA Instalation instruction
Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Installation Guide AWRON Display F36DGA BMW • F36 Gran Coupe Page: 1 Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Page: 2 Table of Contents Table of Contents 2 Scope of delivery 3 Toolkit 4 Cabel system 5 Schematic 6 Installation Guide • • • • • • • • • • • • • • Disassembly interior trim Disassembly panel under the glove box on passenger side Disassembly door sill on passenger side Disassembly side trim on the passenger side Expose the connector from the FEM control unit Dismounting plug CON 2 Dismounting plug CON 3 Unpin cable from connector Pin the cable into the connector Plug CON 3 into the connector Remove plug CON 2 Disassembly trim on the passenger side Plug CON 10 connection Remove plug CON 10 Support & FAQs 7 9 12 13 14 15 16 17 18 20 21 22 24 25 28 Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Scope of delivery F3xDGA Display module Power cord set Page: 3 Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Page: Toolkit Mounting wedge Assembly tool Flat screwdriver 2mm Socket wrench 10mm Screwdriver TORX T25 2mm 4 Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Page: 150cm USB Cabel system 5 Schematic Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Page: 6 Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Page: 7 Disassembly interior trim 1. Remove with a plastic wedge strip the interior. Begin from the right. 2. Pay attention to the connector on startup button and the operating unit warning lights, etc. (see picture below right) 3. Disconnect the connectors, then you can remove air vent. Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Page: 8 Disassembly panel under the glove box on passenger side Unfolding the screw Hex, wrench size 8 mm Unfolding the screw Hex, wrench size 8 mm Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Page: 9 Disassembly panel under the glove box on passenger side No tools required Remove connector No tools required Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Page: 10 Disassembly panel under the glove box on passenger side Remove connector No tools required Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Disassembly door sill on passenger side Use a plastic wedge Unclip side trim Use a plastic wedge Page: 11 Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Disassembly side trim on the passenger side Remove the side panel Use a plastic wedge Unscrew the cover Screwdriver TORX T25 Page: 12 Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Expose the connector from the FEM control unit Remove the side panel No tools required Remove connector CON2 No tools required Page: 13 Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Page: 14 Dismounting plug CON 2 CON10 CON3 CON2 Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Dismounting plug CON 2 Unlocking bracket at the connector solve No tools required Remove connector No tools required Page: 15 Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Unpin cable from connector (CON 2) Remowe connector from the case Flat screwdriver 2mm 18 = PT_CAN_LOW (rot) 19 = PT_CAN_HIGH (blau/rot) 21 20 19 18 17 16 15 14 19 18 Unpin 18 and 19 Pin Flat screwdriver 2mm Page: 16 Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Pin the cable into the connector (CON 2) Pin 1 = PT_CAN_LOW (rot) Pin 2 = PT_CAN_HIGH (blau/rot) Install the supplied white connector No tools required 21 14 Cable red and blue / red from Pin the AWRON cable harness in chamber 18 and 19 No tools required Page: 17 Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Pin the cable into the connector (CON 2) No tools required Page: 18 Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Page: 19 Plug CON 3 into the connector CON10 CON3 CON2 Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Remove plug CON 3 Unlocking bracket at the connector solve Kein Werkzeug notwendig Remove connector Kein Werkzeug notwendig Page: 20 Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Page: 21 Disassembly trim on the passenger side (CON 3) Remowe connector from the case No tools required 20 = Kl.15 (!2V) (braun/grau) 24 = Kl.31 MASSE (braun/schwarz) 19 18 Unpin 20 und 24 Pin Flachschraubenzieher 2mm Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Page: 22 Disassembly trim on the passenger side (CON 3) Pin 1 = Kl.15 (12V) (grün/grau) Pin 2 = Kl.31 MASSE (braun/schwarz) Install the supplied black connector No tools required 19 18 Cable green / brown and brown / black from Pin AWRON cable harness in chamber 20 and 24 No tools required Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Page: 23 Plug CON 10 connection CON10 CON3 CON2 Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Page: 24 Remove plug CON 10 Unlocking bracket at the connector solve No tools required Remove connector 19 18 No tools required Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Page: 25 Remove plug CON 10 Remowe connector from the case No tools required 19 18 Unpin Pin 3 Flachschraubenzieher 2mm Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Page: 26 Remove plug CON 10 Pin 1 = ETH_WUP (blau/gelb) Install the supplied blue connector No tools required 19 18 No tools required Installation Guide: F3xDGA Version: V1.1 Autor: AWRON GmbH Datum: 04.05.2016 Page: 27 Support & FAQs For all enquiries concerning your AWRON display system, or if you have problems with installation guide the AWRON support team at support@awron.de are at your service. Please also seen us and our another AWRON products on our website www.awron.de
Similar documents
front mount intercooler – part #48.10.95
11. Remove plastic outside air temp mount from steel bumper then remove sensor from plastic mount. 15. Using a 13mm wrench, unbolt left-side horn from its bracket. Remove OE bracket and using suppl...
More information