SunMaster Shadow - Tanning Bed Superstore: Tanning Lotions

From
Care and Use Guide
_________________________
Place
Stamp
Here
_________________________
_________________________
UVA SunSystems, Inc.
6208 Technology Dr.
Browns Summit, NC 27214
CUT ON DOTTED LINE
FOLD AT LINE AND SECURE WITH TAPE
SunMaster Shadow
32 Lamp Commercial Tanning Bed
Important!
Read this manual before installing, operating
or servicing this product.
Keep this manual in a safe place, for future reference.
Sales and support:
1-800-274-1744
Sold by: UVA SunSystems, Inc. / SunMasterUSA
6208 Technology Dr., Browns Summit, NC 27214
v-sm32es-1
Revised: June 4, 2012
SPECIFICATIONS
Model
Length
Width
Lamps
Amps
Power
Weight Limit
Shadow (SM32ES)
86” (nominal)
39” (nominal)
32 Power Bronzer 100
14.6
120v / 15A min.
300 lbs
Please completely fill out this warranty card so that your warranty
can be validated.
Name:_______________________
Address:______________________________________________
City:_________________________State:______Zip___________
Email:________________________________________________
GENERAL WARNINGS AND PRECAUTIONS
DANGER: Ultraviolet radiation. Follow instructions. Avoid overexposure. As
with natural sunlight, overexposure can cause eye and skin injury and allergic
reactions. Repeated exposure may cause premature aging of the skin and
skin cancer. WEAR PROTECTIVE EYEWEAR. FAILURE TO DO SO MAY
RESULT IN SEVERE BURNS OR LONG TERM INJURY TO THE EYES.
WARNING: Receive proper operation instructions from the proprietor. When
using a machine with bench and canopy, pull the canopy down until it will
move no futher. Recommended distance of the body from the canopy of this
machine should be 6 inches. Operation of any sunbed closer than the recommended minimum distance for use may result in overexposure.
Medications or Cosmetics: Some may increase your sensitivity to the ultraviolet radiation. Consult a physician before using sunlamps if you are using medications, have a history of skin problems, or believe yourself especially sensitive to sunlight. If you do not tan
in the sun, you are unlikely to tan from the use of this product. Tanning may appear after
one application provided that your skin is capable of developing a suntan. Allow 48 hours
between sessions to obtain a base tan, and once or twice per week to maintain appearance.
Recommended eyewear. Provided eye shields, such as Intrexco Nr: 563511s or equivalent eyewear as defined under 21CFR 1040.20 2(b)(6). One pair of protective eyewear is
furnished with this equipment. Eyewear should be worn by all persons in the room when
the lamps are on. ENSURE THAT THE SUNBED USED CONTAINS COMPATIBLE
LAMPS TO THOSE LISTED HEREIN. ALL SUNBEDS HAVE LABELS STATING COMPLIANCE WITH PERFORMANCE STANDARDS FOR SUN LAMP PRODUCTS UNDER
21 CFR PART 1040.20
BASIC INFORMATION ON THE TANNING PROCESS
Melanin, the brownish pigment produced by special cells in the base layer of the skin,
determines the individual’s ability to tan. As the skin is exposed to ultraviolet rays, the
melanin is activated and combines with protein cells that rise in the skins surface, thus producing a tan. The amount of melanin in your body determines how quickly and darkly you
tan. The tan produced by the sunlamp is a cosmetic tan, however, regardless of how much
an individual may tan with this unit, it will not provide adequate protection against overexposure to natural sunlight or UVB exposure. Use sunscreen outside to protect your skin.
Model #_______________ Serial #_________________________
Purchased from:________________________________________
Sales representative: ____________________________________
I learned about your company from:
___ Internet
____Friend
____Paper
____Other (below)
__________________________________________________
Please give us your comments on the purchasing experience:
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
_____________________________________________________
Signature:
___________________________________
Privacy Policy Statement
Your email and address information will not be sold to any other company. See
website for complete privacy policy, which was desgined to protect your rights.
SOLUTION
Make sure unit is plugged in.
Check outlet, reset breaker if needed.
Verify that cords connecting bed halves to the center timer control are fully
Some of the lights 1. Check to see if lamp is installed correctly.
will not come on. 2. Switch “bad” lamp with a good lamp to see if the problem is the lamp or the
socket.
Canopy won’t stay 1. Make sure shocks are installed properly (ie: thicker part UP)
up or down
2. Replace shock.
Bed cuts off after a 1. Check source of power, reset breaker.
few minutes
2. Make sure cord connecting the bed halves are FIRMLY connected to the
timer box.
WARNING! UNIT MUST BE DISCONNECTED FROM POWER
BEFORE ATTEMPTING ANY MAINTENANCE. INTERNAL MAINTENANCE SHOULD ONLY BE PERFORMED BY A
CERTIFIED ELECTRICIAN OR TECHNICIAN
This unit is designed to be virtually maintenance free. Other than lamps, no other parts are expected
to need replacing for the life of the product. Clean only with the tanning bed solution provided, diluting as instructed on the bottle. More can be purchased at 1-800-274-1744. Using household chemicals can and will cause damage to the acrylic surfaces.
Sunmaster Limited Warranty
All SunMaster and Virtual Sun tanning beds purchased directly from UVA SunSystems, Inc. by phone or through
their websites come with a One Year Limited Warranty, as stated below.
For a period of one year from the date of purchase, UVA SunSystems, Inc. will provide replacement parts for parts
that are shown to be defective. Lamps, acrylics and labor are covered for a period of 30 days. Under all circumstances, transporation is the responsibility of the consumer.
This warranty does not cover: Abuse, misuse, unauthorized repairs or modifications, transportation, damage during
transit or installation, nor normal wear and tear. UVA SunSystems, Inc. or their authorized dealers SHALL NOT BE
LIABLE FOR LOSS OF USE, LOSS OF TIME, RENTAL OR SUBSTITUTE PRODUCTS, LOSS OF INCOME, LOSS
OF BUSINESS, INCONVENIENCE OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL DAMAGES. IN ANY
AND ALL CASES, THE LIABILITY SHALL BE CONFIDED TO THE REPLACEMENT OF DEFECTIVE AND NONCONFORMING PARTS.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above may not
apply to you. This warranty gives you specific legal rights that vary from state to state. No one may modify this warranty in any way. Warranty claims should be made by calling 1-800-274-1744 weekdays from 9am to 5pm, excepting holidays. You may also write to: UVA SunSystems, Inc., 6208 Technology Dr, Browns Summit, NC 27214.
Governing Law: This Limited Warranty shall be governed, interpreted and enforced in accordance with the substantive and procedural as of the State of North Carolina and the United States of America, conflict of law rules not
withstanding.
NOTICES: In order to validate this warranty, you just mail the attached warranty card and mail to the address provided within 30 days from the date of receiving your tanning bed. You must be able to provide a copy of your original receipt upon demand, or your warranty will be voided.
For the purpose of this warranty, the “date of purchase” will be considered the day the system arrives at your home
or other final destination by our carriers.
F-71
F-71
Make sure timer and on/off switch are ON.
Reflex Bronzer
Reflex LT
PROBLEM
Lamps won’t light. 1.
2.
3.
plugged in.
4.
100w
100w
TROUBLESHOOTING AND MAINTENANCE
OPERATING YOUR TANNING BED
BEFORE using tanning bed, cycle the timer one full time to break
in lamps and verify that the timer is counting down accurately.
Motorized (analog) Timer Instructions
The motorized timer will automatically turn the tanning bed on when turned
passed the “0” mark. Turn knob to the desired number of minutes and the bed
will automatically energize and count down.
If your tanning bed came with a “shorting plug”, then it was designed to work with
either the onboard timer, or with a remote timer for commercial use. (Remote
timer is not included). Using a remote timer requires a special cord to replace the
shorting plug on the back of the tanning bed, which then connects to the remote
timer itself. If a remote timer is used, then the onboard timer will act as an ON /
OFF switch. The timer will not count down, but will allow the bed to be turned on
and off if the remote timer is set to the ON position and timing down as well. This
is provided so that customers in the salon will always have the option to turn the
bed off before the full session is complete.
Additionally, the “shorting plug” can be used in the home environment to disable
the tanning bed, and prevent unauthorized persons from using it. In this configuration, it works as a safety device. Simply twist the locking mechanism and
remove the shorting plug to disable the tanning bed. This will not remove power
to the tanning bed, but will disable the timer so that it can not be energized. To
restore function, simply replace the shorting plug. The shorting plug can always
be found on the back edge of the canopy of the tanning bed.
Universal ballast diagram
To remove the shock, you need to
gently pry the metal clip back, but
not off, then pull end off the ball.
Final steps: Make sure the “shorting plug” is installed into the
timer port on the back of the bed. (not shown) This is a safety
lock feature, and the bed will not operate unless this is in
place. Now plug the cord from the bench into the slot of the
canopy, to provide power to both halves, then plug in the wall.
Once the bed is fully assembled and plugged into the wall, be
sure to run the bed one full cycle without actually tanning, to
insure the timer is operating properly.
This next step takes two strong persons, as you connect the hinge
bolt into the canopy of the bed, allowing it to swivel. NOTE: Be
sure to follow the diagram exactly in respect to the washers!
Once you have completed this step, you will then insert the back
bar that says “Shadow” in between the two hinges using the four
supplied bolts. After these steps are all complete, you will then
tighten all the bolts in the hinges until the are snug. You don’t
need to over-tighten them.
Installing your new SunMaster E Series tanning bed
Start by assembling the leg kit. It will be in a large cardboard box,
along with all the misc. hard ware.
(Note: the triangle pieces shown are no longer included in the kit)
Next, you will roll the bench of the tanning bed (the half that
does NOT have a timer) upside down, then attach the leg kit
using 6 screws. Again, the triangle pieces shown here are no
longer included. You do not need to overtighten these screws.
Now turn the unit right side up, and place it in its final
destination. It is easier to move now than with the full weight of
the bed.
Once you have have turned the bench right side up, you will
attache the hinges to the bench. It is often helpful to leave the
bolts slightly loose during the next few steps, to allow it to flex and
the bolts and holes to line up easier.