Pataco TURTLE

Pataco TURTLE
SI8S TURTLE
SI8M TURTLE
EN
COMPONENT INSTRUCTION
Clutch
Mechanical switch
Speaker
Socket
Sensivity switch
Rubber pad
Base plate
Slider
LED
Tape clamp
Transportation security clip
Battery cover
Silicon bumper
Slot
Movement sensor
MULTI ALARM TECHNOLOGY
Alarm 1
Alarm 2
Alarm 3
Alarm 1:
Armed TURTLE triggers EAS systems.
Alarm 2
Alarm 4
Alarm 2-4:
Anti-tamper, TURTLE will full alarm if sensor
wire is cut or dampered with.
Pataco AG
Looäcker 1
CH-9247 Henau, Switzerland
www.pataco.com - info@pataco.com
Int. Freecall: +800 72 82 26 24
INSTRUCTION MANUAL
1
© Pataco AG 09/2014 release 2.0
Pataco TURTLE
SI8S TURTLE
SI8M TURTLE
EN
PRE-ALARMING
Pre-Alarm
Pre-Alarm
Small movement of the Turtle causes a pre-alarm
of three beeps
The pre-alarm acts as a deterrent.
HOW TO STOP ALARMING
Open the Turtle by placing the detacher onto the clutch.
The alarm will stop immediately.
HOW TO CHANGE BATTERY
screwdriver to take the
1 Use
Battery cover screw out.
Pataco AG
Looäcker 1
CH-9247 Henau, Switzerland
www.pataco.com - info@pataco.com
Int. Freecall: +800 72 82 26 24
battery cover as
2 Open
indicator shows
3 Change battery
INSTRUCTION MANUAL
2
Pataco TURTLE
SI8S TURTLE
SI8M TURTLE
EN
APPLICATION WITH PACKING STRAP
the transportation
1 Remove
security clip
2
Insert base plate under the
cross of packing strap, make
sure packing strap is in the
slot of base plate.
Turtle on base plate and
3 Close
press down until lock.LED
flashes once and speaker beeps
once indicate merchandize
protected.
Pull
HOW TO REALEASE - APPLICATION WITH PACKING STRAP
the magnetic detacher onto
1 Place
clutch and press to open Turtle.
out Turtle from packing
2 Take
strap.
the carton box as transport
3 Use
device from cashier to stock!
APPLICATION WITH GLUE STRIPE
surface of merchandise and Turtle
1 The
has to be cleaned with an alcohol pad
to ensure maximum glue force.
Pataco AG
Looäcker 1
CH-9247 Henau, Switzerland
www.pataco.com - info@pataco.com
Int. Freecall: +800 72 82 26 24
INSTRUCTION MANUAL
3
Pataco TURTLE
SI8S TURTLE
SI8M TURTLE
EN
APPLICATION WITH GLUE STRIPE
a glue stripe and remove
2 Take
one release paper.
the glue stripe into the
3 Stick
slot of base plate.
the end of the glue stripe
4 Place
into the tape clamp.
the Turtle then remove the
5 Close
second release paper
The TURTLE onto the
6 Attach
merchandise and press down to
LED flashes once and
7 Now
speaker beeps once to indicate
make sure it sticks tight on the
merchandise.
merchandise is protected.
HOW TO REALEASE - APPLICATION WITH GLUE STRIPE
1
Place the ejecter onto the clutch
and press to open the TURTLE.
out the end of the glue stripe
2 Take
from tape clamp, hold the Turtle
3
Take off TURTLE from
merchandise.
tightly and pull the glue stripe
horizontally
Pataco AG
Looäcker 1
CH-9247 Henau, Switzerland
www.pataco.com - info@pataco.com
Int. Freecall: +800 72 82 26 24
INSTRUCTION MANUAL
4
Pataco TURTLE
SI8S TURTLE
SI8M TURTLE
EN
APPLICATION WITH SENSOR
as step 1 to 6 of
1-6 Same
"Application with glue stripe".
9
Take off the release paper from the
sensor head.
in the end of the sensor
7 Plug
cable into the socket.
the sensor head onto
10 Stick
merchandise. Use a cable tie
the sensor cable around
8 Wiring
the strain-relief.
the TURTLE and press
11 Close
down until it locks.
for better holding if required
(optional)
HOW TO REALEASE - APPLICATION WITH SENSOR
Same as step 1 to step 3 of "How to realease - Application with Glue Stripe".
HOW TO REALEASE THE SENSING HEAD
1
Take off the glued
sensor by rotating the
sensor head.
Pataco AG
Looäcker 1
CH-9247 Henau, Switzerland
www.pataco.com - info@pataco.com
Int. Freecall: +800 72 82 26 24
INSTRUCTION MANUAL
5
Pataco TURTLE
SI8S TURTLE
SI8M TURTLE
EN
SPECIFICATION TURTLE
Frequency:
58kHz / 8.2MHz
Dimension:
Ø65mm x 35mm
Color:
black, white or customize
Beep volume: 95dB
Battery life:
3 years
Lock:
super or normal magnetic
Battery:
CR2450
Usage environment
Temperature:
0 ~ 40°C (32 ~ 104°F)
Humidity:
20% ~ 85%
Alarm duration: 5 minutes
SPECIFICATION GLUE STRIPE
Temperature:0 ~ 40°C (32 ~ 104°F)
Humidity:20% ~ 85%
Max strength after 30 minutes: 2800g / 20mm (stick 20mm width stripe on stainless metal under 23°C and 65% RH
NOTES
• Working indicator:
1. While locking the TURTLE, LED flashes once and speaker beeps once.
2. No LED flash when the TURTLE is armed.
3. During alarming, the speaker beeps continuously and LED flashes.
4. During Pre-Alarm speaker beeps three times.
• Low battery indicator:
LED flashes 10 times continuously when becomes armed.
Please change battery when low battery indicates.
• Defective TURTLE must be duly disposed. The battery and the TURTLE must to be disposed of separately from each other and not be allowed to arrive into the household refuse.
• Pre-Alarm sensivity:
Position 1: low sensitive (alows larger movements without alarming)
Position 2: medium sensitive (delivery status)
Position 3: high sensitive (alarm is triggered by small movements)
Pataco AG
Looäcker 1
CH-9247 Henau, Switzerland
www.pataco.com - info@pataco.com
Int. Freecall: +800 72 82 26 24
INSTRUCTION MANUAL
6