Mounting instruction for conversion kit Monster mod

Transcription

Mounting instruction for
conversion kit Monster models 2WD/RTR to 4WD
Item N°. 68500
conversion kit Marder 2WD/RTR to 4WD
Item N°. 68501
FG Modellsport GmbH
Spanningerstr. 2
73650 Winterbach-Germany
Phone: +49 7181 9677-0
Fax: +49 7181 9677-20
info@fg-modellsport.de
www.fg-modellsport.de
conversion kit Baja Buggy 2WD/RTR to 4WD
Item N°. 68502
A.68500-68502-D-200309
Please thoroughly keep this construction
manual for your spare parts orders!
Marder
Monster models
Baja Buggy
The handling with fuels requires circumspective and careful handling. Imperatively observe the security advices.
-Refuel only if the engine is switched off!
-Take off the body.
-Thoroughly clean the area around the fuels nipple.
-Remove the fuel filler cap and carefully fill in the fuel mixture.
-Smoking or any kind of open fire is not admitted.
-Fuels might contain solvent-like substances. Avoid contact with skin
and eyes. Wear gloves for refueling. Do not inhale fuel vapors.
-Do not spill any fuel. If you have spilled fuel immediately clean the
engine and the model.
-Make sure that no fuel will get into the soils (environmental protection). Use an appropriate mat.
-Do not refuel in enclosed rooms. Fuel vapors accumulate at the soil
(risk of explosion).
-Transport and store fuels only in admitted and labeled canisters. Keep
fuel out of the range of children.
-The operator is responsible for any damages caused to third persons
in the operating range of the model, respectively of the engine, if they
are injured or in case of property damage.
-The model must only be passed on to persons who are familiar with
this model and its operation, always provide the operating manual.
-Persons with implanted heart pacemakers must not work on running
engines and on live parts of the ignition system when the engine is
being started.
-The engine must neither be started nor operated in enclosed rooms
(without sufficient ventilation).
-When starting the engine, avoid inhaling the exhausts.
-The model must neither be started nor operated without air filter or
without exhaust system.
-Before every start perform a functional check of the safety-relevant
parts.
-The throttle rods must always return automatically to the idle position.
-Any cleaning, maintenance and repair works must only be performed
with the engine being switched off. The engine and silencers are getting very hot. In particular do not touch the silencer.
As 4WD models have raised steering forces compared
to 2WD models we recommend to use only servos with
metal gear for steering.
Comments regarding the construction manual:
Before starting the assembly please see through this construction
manual. This way you will get an overview of the whole execution.
Please check by means of the parts or bag list if the construction kit is
complete and also check the weight of the individual bags for the positions. Only this way you may be sure that all parts which you need for
the assembly are available. If a part is missing, please immediately
contact your specialized dealer.
Contents
Position 1-2: Front and rear differential gear
Position 3-7: Belt drive, belt stretcher, chassis structure
Position 8-15: Rear axle
Position 14-15: Front and rear shock absorber
Position 16-26: Front axle, front bumper
Position 30-36a: Engine, clutch, gear, air filter, tank
Position 37-43: RC-plate, receiver box, servo saver
Position 44-46: Roll cage, throttle rods
Position 47-50: Body mounts, side plates, roll cage parts
Position 52-56: Body trimmings
All metric screws need to be secured with thread lock fluid.
Reusable parts from your 2WD model have to be checked carefully on their condition, defective and worn parts
should be replaced.
Diff. bevel gearwheel B
Differential
Diff. driving axle
Diff. bevel
gearwheel A
Ball bearing
12x28x8
Steel gearwheel
48 teeth
Screw
M4x40
Rear plastic gear
disk 42 teeth
Plastic stop
disk right
Differential
housing
Stop nut M4
Diff. bevel
gear axle
Position 1
Parts are in
bag B
Steel gearwheel
48 Zähne
Rear
differential
Plastic stop
disk right
Ball bearing
12x28x8
Differential
housing
Ball diff.
driving axle
Stop nut M4
Screw
M4x40
Slant to the
inside
Rear plastic gear
disk 42 teeth
Inserting of the diff.
bevel gearwheels or
of the complete
package is much
easier if you use the
FG mounting tool
08505.
Slant to the
inside
Lubricate
slightly
Mounting of the rear differential gear
1. Press the ball bearing 12x28x8 on the differential housing.
2. Insert the differential bevel gearwheels in the differential housing as
pictured in position 1. When using the FG mounting tool Item N°.
08505 the inserting of the bevel gearwheels will be eased considerably.
3. Lubricate the diff. driving axles slightly with grease and push them in
the diff. housing.
4. Mount the diff. bevel gear axle. If the bevel gear axle resperctively
the driving axles can only be pushed in severely or if it is impossible to
push them in at any position, you have to disassemble the bevel
gearwheels again and insert them once more.
5. Lubricate the gearwheels slightly with multipurpose grease, e.g. Item N°.
06501.
6. Now press the parts on the diff. housing as described in position 1
and in the given sequence: Steel gearwheel 48 teeth ( consider mounting direction of the slant), rear plastic gear disk 42 teeth, plastic stop
disk right. Fix the complete unit with the M4x40 countersunk screws
and stop nuts M4 (impress the M4 stop nuts in the plastic stop disk
right and use the screw retention high-strength).
Position 2
Parts are in
bag C
Front plastic
stop disk
right
Front
differential
Differential
housing
Stop nut M4
Mounting of the front differential gear
1. For mounting of the front differential gear you have to disassemble
the differential from your 2WD model, remove diff. bushing and steel
gearwheel 48 teeth.
2. Now mount the parts on the diff. housing as described in position 2
and in the given sequence: Front plastic stop disk left (consider mounting direction of the slant), front plastic toothed belt wheel 42 teeth, plastic stop disk right. Fix the complete unit with the M4x40 countersunk
screws and the stop nuts M4 (impress the M4 stop nuts in the plastic
stop disk right and use the screw retention high-strength).
3. Push the bearing shafts 6x50mm centrally in the deflection roller
16mm and in the 12-teeth toothed belt wheel.
Right plastic
stop disk
Screw
M4x40
Slant to the
outside
Front plastic
toothed belt
wheel 42 teeth
Bearing
shaft 6x50
Bearing
shaft 6x50
Deflection roller
16mm
Toothed belt
wheel 12 teeth
Front differential
mounted
Position 3
Parts are in
bag C
2. Mount front differential gear, deflection roller
16mm, toothed belt wheel 12 teeth in the left
front axle housing as described in position 3.
Front axle
housing left
3. Now put the toothed belt on the front differential gear, also deflection roller 16mm,
toothed belt wheel with 12 teeth as described in position 3.
Toothed belt wheel
12 teeth
Deflection roller
16mm
Toothed belt
Front axle
housing right
4. Press the right front axle housing on the front differential gear, also deflection roller 16mm and the toothed belt wheel with 12 teeth (position 4).
Position 4
Parts are in
bag C
Front axle
housing left
1. Impress ball bearings 6x16x6 in both front
axle housings left and right.
5. Put the complete front axle housing on
the alloy chassis and fasten it using the
4,2x16 countersunk screws.
Front differential
gear
Alloy chassis
Front axle
housing right
Position 5
Parts are in
bag B+C
1. Put the toothed belt around the rear differential gear
as described in position 5.
2. Press the left and right rear axle mounts on the ball
bearings of the rear differential gear as pictured.
3. Put the left and right rear axle mounts on the alloy
chassis and fix them with the 4,2x16 countersunk
screws on the chassis.
Rear axle mount
left
Countersunk
screw M4,2x16
Upper part belt
channel
Toothed belt
Lower part belt
channel
When mounting pay attention that the closed side of the lower belt channel faces
upwards. The teeth of the toothed belt are
not allowed to touch each other.
1. Place the lower part of the belt channel (with the closed side facing
upwards) on the bottom part of the toothed belt. Then push the top part
of the belt channel in the bottom part. Now insert the complete belt
channel in the opening of the front axle housing (see position 5a). Make
sure that the toothed belt is running smoothly.
2. Fix the belt channel from underneath to the alloy chassis using the
4,2x16 countersunk screws.
Rear axle mount
right
Countersunk
screw M4,2x16
Front axle housing left
Position 5a
Parts are in
bag B+C
Fix the belt channel from underneath to the alloy
chassis with the 4,2x16 countersunk screws.
Alloy chassis
Front axle
housing
right
Upper part
belt channel
Toothed belt
Lower part belt
channel
Position 6
Parts are in
bag B
Screw
M4x14
1. Impress the plastic bearing seat
Disk Ø4,3 with inbound collar (pay attention to
Screw
4,2x16
Countersunk
screw M4,2x16
fitting position) in the left and right
stretching pulley housing as described in position 6.
Fitting position for
toothed belt wheel
40 teeth
Tipp: The position of the front bearing seat is made for
the front plastic toothed belt wheel with 42 teeth. The
position of the rear bearing seat is made for the front
plastic toothed belt wheel with 40 teeth.
Fitting position for
toothed belt
wheel 42 teeth
Stretching pulley
housing left
2. Push the bearing shaft for the stretching pulley
housing centrically in the 3 ball bearings 10x19x7.
Ball bearing
10x19x7
3. Impress the bearing shaft which is equipped with
ball bearings in the bearing seat of the left and
right stretching pulley housing and fix it with
M4x14 pan-head screws and Ø4,3 disks.
Bearing shaft
for stretching
pulley housing
Collar
Plastic
bearing seat
Stretching pulley housing
right
Position 7
Parts are in bag B
1. Place the mounted stretching pulley housing ob toothed belt and belt channel as described in position 7
and fix it on the alloy chassis using the 4,2x16 countersunk screws. For this purpose, slightly move the belt.
2. When the assembly is performed, turn the belt in running direction. Make sure the belt is easily rotatable.
Belt channel mounted
Stretching pulley
housing mounted
Countersunk
screw 4,2x16
Alloy chassis
Position 8
Parts are in
bag D
Stabilizer
5mm
Screw
M4x20
4. Impress the stabilizer 5mm (only for Monster/Stadium
models) in the plastic braces for stabilizer.
Disk
Ø4,3
Rear axle mount
right
Alloy connection brace
Rear axle cover
1. Push the rear axle cover between the left
and right rear axle mounts and fix it with the
alloy connection brace, M4x20 pan-head
screw and disk Ø4,3.
2. Disassemble the rear lower wishbone with
stabilizer from your 2WD model (stabilizer
only in Monster/Stadium models).
3. Fix the rear lower wishbones to the front
ball-and-socket joints using M5x30 countersunk screws and 4 disks Ø5,3 (between balland-socket joints and alloy chassis), then fix
all with M5 stop nuts to the alloy chassis.
Now fasten the rear ball-and-socket joints
with M5x25 countersunk screws and M5
stop nuts to the alloy chassis. Make sure the
mounted wishbones can be moved easily up
and down.
Rear axle mount
left
Stop nut M5
Screw
M5x25
Ball-andsocket joint
Adjusting screw
r/l 32mm
Disk Ø5,3
Alloy chassis
Screw
M5x30
Plastic brace for
stabilizer only for
Monster/Stadium
ap
pr
ox
.3
8m
m
Position 9
Parts are in
bag D
m
7,5m
ox. 3
appr
Adjust the setting screws
corresponding to your
existing model.
Rear lower
wishbone
Rear damper
plate 4WD
Position 10
Parts are in
bag D
1. Mount the 4WD damper plate rear to the left and right
rear axle mounts using 4,2x22 pan-head screws.
2. Push the stabilizer (only Monster/Stadium models) into
the rear damper plate and fasten it with 4,2x9,5 pan-head
screws and disks Ø4,3.
3. Disassemble rear uprights, rear driving shafts and rear
lower wishbone pins from your existing 2WD model and
impress them in the rear lower wishbones as described in
position 10+11. Secure the wishbone pins with Ø5 retaining washers.
Screw
4,2x22
Screw
4,2x9,5
Disk Ø4,3
Rear lower
wishbone
Rear axle
mount left
Rear lower
wishbone pin
Rear driving
shaft
Retaining
washer Ø5
Rear upright
left
Position 11
Parts are in bag D
Stabilizer 5mm only in
Monster/Stadium version
Position 12
Parts are in
bag D
1. Disassemble the rear upper wishbone pin and the
ball-and-socket joint with steel ball from your existing
2WD model.
2. Screw the rear wishbone thread rods M10/M8 84mm into
the rear upper wishbones and in the ball-and-socket joints
to the size of approx. 77mm.
3. Fix the completely mounted rear upper wishbones at
the rear axle mounts by using wishbone pins, then
mount the rear damper plate. Secure the wishbone pins
with Ø5 retaining washers.
Rear damper
plate
Retaining
washer Ø5
Adjusting clips
Rear upper
wishbone pin
Headless pin
M5x25
Rear upper
wishbone
Rear wishbone
thread rod
M10/M8 84mm
Ball-and-socket joint
Left upright
Position 13
BaustufeParts
14 are in
Teile sind bag
in D
Beutel
4. Push two adjusting clips each in the rear upper
wishbone pins in the front between rear axle mounts
and rear upper wishbones, then push one adjusting
clip each in the rear upper wishbone pins in the rear
between rear damper plate and rear upper wishbones.
According to the toe-in
adjustment the upper
wishbone needs to be shimmed by adjusting clips.
5. Fix the ball-and-socket joints with steel
ball (steel ball collar must face the upright)
at the uprights using M5x35 countersunk
screws and disks Ø5,3, see position 12+13.
6. Screw M5x25 headless pins from above
into the rear upper wishbones (rebound stop
travel).
Screw
M5x35
approx. 6mm
m
7m
.7
rox
p
ap
Disk
Ø5,3
Make sure the driving shaft has not
more than 2-3mm clearance in horizontal position. Adjust the adjusting screws
of the rear axle correspondingly.
Disk Ø5,3
Steel ball
10x13
Screw
M5x35
Make sure the rear wishbones
can be moved easily up and
down.
Mounting of rear shock absorbers Marder/Baja
1. Mount o-rings 13x2,5 on the top of shock absorber locking M5 and lower
shock absorber locking A (position 14/14a).
2. Push retaining washer Ø3,2 in the first slot of the long damper piston
rod, then mount the damper piston with the recess facing towards the
retaining washer and fix it with a second retaining washer Ø3,2 (position
14b).
3. Press the lower shock absorber locking B (with the flat side facing the
damper piston), two o-rings 4x2 and upper shock absorber locking A
(with the thread facing the damper piston) on the long damper piston
rods.
4. Screw the short damper fixing on the thread of the long damper piston
rod until the thread is no longer visible. Now press it in the shock absorbers housing and screw it tight (position 14b).
5. Pull out the damper piston rod completely and fill the shock absorber
housing with oil to the start of thread. Now slide the damper piston rod
slowly several times in and out the shock absorber housing so that the
air bubbles in the oil will come upwards. If no longer air bubbles appear,
push the damper piston rod slowly into the shock absorber housing until
there are only approx. 5mm visible of the piston rod (position 14c). Then
screw the upper shock absorber lockings M5 on the shock absorber
housings (position 14d).
6. Mount one narrow and one wide damper collet each and a blue damper pressure spring on the shock absorber housings and secure them
with the spring collars (Position 14e).
Mounting of front shock absorbers Marder/Baja
1. Dismount the rear shock absorbers from your existing 2WD model and
disassemble damper pressure springs, spring collar, damper fixings and
damper collets.
2. Screw the short damper fixings on the thread of the damper piston
rods until the thread is no longer visible.
6. Mount two narrow damper collets and a violet damper pressure spring
on the shock absorber housings, secure them with the spring collars
(position 14e).
Hint: Slightly lubricate the o-rings with
silicone oil when mounting. If you use
the FG mounting tool 06853 + 06854,
the mounting of the shock absorbers
will be eased considerably.
Position 14e
Position 14
Parts are in
bag E
Marder/Baja
Mount o-ring 13x2,5
on the top shock
absorber locking.
Position 14a
Parts are in
bag E
Mount o-ring 13x2,5
on the lower shock
absorber locking.
Front damper
mounted
Rear damper
mounted
Position 14c
Parts are in
bag E
Position 14b
Parts are in
bag E
Fill up with oil
to the start of
thread.
Damper piston
Retaining
washer Ø3,2
Lower shock
absorber locking B
O-ring
4x2
Lower shock
absorber locking A
Damper piston
rod long
Damper fixing
short
Mounting of shock absorbers Monster/Stadium
1. Mount the o-rings 13x2,5 on the upper shock absorber lockings M5 (position 14).
2. Dismount four shock absorbers from your existing 2WD model ans disassemble damper pressure springs, spring collar, damper fixings and damper
collets.
3. Screw two long and short damper fixings each on the thread of the
damper piston rod until the thread is no longer visible.
4. Dismount the upper shock absorber lockings M4, remove the oil from
the shock absorbers.
5. Pull out the damper piston rod completely and fill the shock absorber
housing with oil to the start of thread (position 14c). Now slide the damper piston rod slowly several times in and out the shock absorber housing so that the air bubbles in the oil will come upwards. If no longer air
bubbles appear, push the damper piston rod slowly into the shock absorber housing until there are only approx. 5mm visible of the piston rod.
Then screw the upper shock absorber lockings M5 on the shock absorber housings (position 14d).
6. Mount each two narrow damper collets, one violet damper pressure
spring on the shock absorber housings with the long damper fixings and
secure with spring collars. Now mount each two wide damper collets,
one blue damper pressure spring on the shock absorber housings with
the short damper fixings and secure with spring collars (position 14f).
Position 14d
Parts are in
bag E
Position 14f
Monster/Stadium
Push the piston
rod in, then
unscrew the
shock absorber
locking at the
top.
Front damper
mounted
Rear damper
mounted
Position 15
Parts are in
bag E
Stop
nut M5
Nut
M5
Screw
M5x25
Rear damper
plate
Rear shock absorber mounted
Screw M5x25 cylinder screws into the rear
damper plate and counter with M5 nuts,
then fix the top of the shock absorber with
M5 stop nuts. Don’t tighten the stop nut.
Mount the rear shock absorbers to the rear
lower wishbones by using M4x30 headless
pins.
Hint: In order to withdraw the front lower wishbone
pins, screw an M4 screw into the threaded hole of
the front lower wishbone pins.
A clearance of the steel ball in the front lower
wishbone can be adjusted with the 2,9x13 screw.
Position 16
Parts are in
bag F
All metric screws need to be secured
with thread lock fluid.
Front axle
housing
right
3. Insert the front lower wishbones in the front axle housings, then
push the front lower wishbone pins with threaded hole towards
the front in the front axle housings and press them through the
pre-assembled front lower wishbones. Make sure the wishbones
can be moved easily up and down.
Screw
4,2x16
Front axle
housing left
1. Screw the headless pin M5x16 from the
Guide for
stabilizer
Headless bottom into the front lower wishbone until
pin
approx. 2mm thread are visible.
M5x16
Front lower
wishbone pin
4. Impress the stabilizer guide as
locking device for the front lower
wishbone pins into the left and right
front axle housings and fix it using
4,2x16 pan-head screws.
Front lower
wishbone
Screw
2,9x13
2. Disassemble the steel balls from the front axle of your existing 2WD model and push them into the front lower wishbones, then screw in the 2,9x13 pan-head screws.
Steel ball
Fixing nut for
front upright
Position 18
Parts are in
bag F
Front upright
4WD left
Front upright
4WD right
Position 17
Parts are in
bag F
Ball bearing
17x26x7
Ball bearing
8x22x7
1. Impress mounting nuts for front uprights from the
inside into the left and right uprights.
2. Push the ball bearing 17x26x7 from the inside into
the left and right upright.
3. Disassemble the ball bearing 8x22x7 from the
upright of your existing 2WD model and push it into the
front upright 4WD.
Fixing nut for
front upright
Disk
Ø8,4
Retaining
washer Ø5
Adjusting
clips
Diff. driving axle
Front upper
wishbone
pin
Front axle
housing
Front lower
wishbone
Headless
pin
M5x25
Front upper
wishbone
Screw
M5x30
Disk
Ø5,3
Front driving shaft
Disk
Ø5,3
Front wishbone
thread rod
M10/M8 66mm
Front upright
4WD left
Front
driving
axle
Headless pin
M6x6
Ball-and-socket joint
Screw
M5x30
Steel
ball
Disk
Ø5,3
Disk
Ø5,3
Position 19
Parts are in
bag F
1. Screw the front wishbone thread rods M10/M8
66mm into the front upper wishbones, then turn
the ball-and-socket joints on the front wishbone
thread rods M10/M8 66mm.
2. Dismount the steel balls from your existing
2WD model and press them into the ball-andsocket joints.
3. Press the front upper wishbone pins through
the pre-assembled front upper wishbones into the
front axle housings as described in position 19.
Fix the front upper wishbone pins with Ø5 retaining washers.
4. Withdraw the diff. driving axles from the front
differential and press them with disk Ø8,4 in the
front differential again.
5. Push the front driving axles into the pre-assembled left and right uprights. Dismount square
wheel driver from your existing 2WD model and
mount it on the faces of the front driving axles
with the crank facing the bearing.
Square wheel
driver 14mm
Screw the M5x25 headless
pins from above into the
front upper wishbones.
Impress four adjusting clips each in the
front between front axle housing and front
upper wishbones into the front upper
wishbone pins.
Make sure the driving shaft has not more than 2mm
clearance in horizontal position. Corresponding to the
adjustment of the upper wishbone (camber) you have
to mount or dismount enclosed steel disk Ø8,4 between diff. axle and ball bearing.
ap
pr
ox
.19
,5m
m
m
5m
9,
..4
ox
pr
ap
approx. 7,5mm
Screw
M5x30
Disk
Ø5,3
Front upright
left
Mount the left and right
uprights to the lower wishbones and to the ball-and-socket
joints of the upper withbones
using Ø5,3 disks between
steel ball, screw and uprights.
At the same time mount the
driving shaft between front
driving axle and diff. driving
axle.
Baja Buggy Position 20+21
1. Fix the front shock mount 4WD to
the reinforcing plate for the front axle
by using M4x16 countersunk screws,
Ø4,3 disks and M4 stop nuts.
Disassemble countersunk screw
M4x25 and M4 nut from the shock
mount of your existing 2WD model and
mount them at the front shock mount
4WD.
2. Mount the plastic fixing plate with
brake guide rail and alloy distances
between brake guide rail and reinforcing plate to the reinforcing plate for
the front axle using M4x30 cylinder
screws, disks Ø4,3 and M4 stop nuts.
Position 20
Parts are in
bag G
Baja Buggy
Stop nut M4
Screw
M4x16
Screw
4,2x13
Disk
Ø4,3
Reinforcing plate
for front axle
Plastic fixing
plate
Screw
M4x25
Nut
M4
Brake
guide
rail
Front shock
mount 4WD
Alloy
distance
Disk
Ø4,3
Position 21
Parts are in
bag G
Disk
Ø4,3
Baja Buggy
Screw
M4x30
Stop nut M4
Marder Position 22
1. Fix front shock mount 4WD to the reinforcing plate
for the front axle using M4x16 countersunk screws,
disks Ø4,3 and M4 stop nuts.
Dismount countersunk screw M4x25 and M4 nut from
the shock mount of your existing 2WD model and
mount them in the 4WD shock mount.
2. Cover the rear bore holes of the reinforcing plate for
the front axle with an adhesive tape to prevent a contamination of the gearwheel drive.
Position 22
Parts are in
bag G
Marder
Screw
M4x16
Adhesive
tape
Front shock
mount 4WD
Screw
4,2x13
Nut
M4
Reinforcing brace
for front axle
Screw
M4x25
Marder/Baja Buggy
Position 23
Parts are in
bag G
Disk
Ø4,3
Stop nut
M4
Screw
4,2x13
Stop
nut M4
Screw
4,2x16
Front bumper
Disk
Ø4,3
Screw
M4x8
Screw M4x14
Marder/ Baja Buggy Position 23
1. Fix the assembled reinforcing plate for the front
axle on the front axle carriers using 4,2x13 pan-head
screws.
2. Mount the front shock absorbers at the front lower
wishbones using M4x14 cylinder screws, then fix the
top of the shock absorber with M4 stop nuts.
3. Assemble the front bumper with M4x8 pan-head
screws and Ø4,3 disks to the alloy chassis and with
4,2x16 pan-head screws at the front axle carriers.
Position 24
Parts are in
bag G
Front shock
mount 4WD
Monster/Stadium
Plastic part for
reinforcing plate
Headless pin
M5x45
Nut M5
Screw
4,2x16
Screw
4,2x32
Reinforcing plate for
front axle
Body mount short,
80mm, adjustable
Body support
Screw
4,2x13
Body clip
Screw
4,2x16
Dampening rubber
for body support
Screw
4,2x13
Monster/Stadium Position 24-25
1. Mount front shock mount 4WD to the reinforcing plate for front axle
using 4,2x16 countersunk screws.
2. Dismount the plastic parts for reinforcing brace from the shock mount of
your existing 2WD model and fix them to the front shock mount 4WD by
using 4,2x32 countersunk screws (position 25).
3. Screw the headless pins M5x45 from the front into the front shock
mount 4WD until they are flush with the rear side of the shock mount.
Then counter the headless pins witrh M5 nuts.
4. Disassemble the adjustable body mounts from the shock mount of
your existing 2WD model and mount them to the front shock mount
4WD by using 4,2x16 pan-head screws.
5. Fix the body clips in the adjustable body mounts as described in position
25 and press on the body support. Use the body clips and the body support from your existing 2WD model.
Monster/Stadium
Position 25
Parts are in
bag G
Nut M5
Plastic
mount
Headless
pin M5x45
Screw
4,2x32
Position 26
Parts are in
bag G
Monster/Stadium
Stop
nut M5
Monster/Stadium Position 26
1. Fix the assembled reinforcing plate for front axle
on the front axle carrier using 4,2x13 pan-head
screws.
2. Mount the front shock absorbers to the front lower
wishbones with M4x14 cylinder screws, then fix the
shock absorbers at the top with M5 stop nuts.
3. Assemble the front bumper at the alloy chassis
using M4x8 pan-head screws and disks Ø4,3, then fix
it with 4,2x16 pan-head screws at the front axle carriers.
Screw
4,2x16
Front bumper
Screw
M4x8
Disk
Ø4,3
Screw M4x14
Position 30
Parts are in
bag H
1. Cover the outlet port of the engine
with an adhesive tape.
2. Saw off the housing part
with an metal hand saw, see
also illustration in position 31.
Dr
ivin
gd
ire
cti
on
Position 31a
Parts are in
bag H
Clutch spring
Clutch blocks
Position 30b
Parts are in
bag H
1. Disassemble the complete engine from your existing 2WD model.
Remove muffler, airfilter, gearplate and clutch. Make sure no dirt gets in the outlet port of the engine.
2. Dismount the clutch spring by twisting the clutch blocks.
3. Mount new clutch spring as described in position 30a-30c.
4. Now disperse the clutch blocks slightly until the clutch blocks lay straight parallel again, position 30b.
5. Push the clutch blocks on top of each other by using tongs or a vice, until they lock. Position
30c.
6. Push the shaft washers on the dowel screws for the clutch blocks and press them into the
clutch blocks from the side with the arrows (engine running direction). Fix them on the clutch
block carrier using 6x15x1 disks. Position 30d and 31.
7. Disassemble steel fixing plates and ball bearing 10x19x7 from the existing 2WD parts and
mount them to the large plastic mount 4WD.
8. Now mount the large plastic engine mount 4WD with the long and short steel fixing plates on
the engine using 4,2x13 pan-head screws as described in position 31.
Hint: If you use the FG piston punching pin Item N°. 08542 the mounting of the clutch will be considerably simplified.
Position30c
Parts are in
bag H
Position 31
Parts are in
bag H
Position 30d
Parts are in
bag H
Plastic engine
mount large
4WD
Ball bearing
10x19x7
Disk
6x15x1
Steel fixing plate long
Shaft washer
Screw
4,2x13
Steel fixing plate short
Screw
4,2x13
Dowel screw for
clutch blocks
Make sure that driving gearwheels, driving shafts
a.s.o. can be turned easily without any resistance.
Position 32
Parts are in
bag I
Basic
body
Airfilter
adapter
Screw
4,2x13
Screw
4,2x13
Gearwheel
cover gear
Screw
M6x16
ge
flan
chl
t
u
l
C
Gear
shaft
4WD
Steel
gearwheel
14 teeth
Headless
pin
M5x5
Screw
4,2x13
Insert the o-ring for the airfilter
adapter in the basic body and
fasten it to the airfilter adapter
Press the oiled foam filter of your
existing 2WD model on the basic
body and fix it with filter cover and
4,2x16 countersunk screw.
Mount the gearwheel cover at the large plastic
engine mount 4WD using 4,2x13 pan-head
screws as described in position 32+34.
Gear
plate
1. Remove the adhesive
tape from the outlet port of
the engine and re-assemble
muffler with muffler gasket
from your existing 2WD
model.
Screw
4,2x16
Filter cover
O-ring for airfilter
adapter
Plastic engine
mount large
4WD
Foam filter
3. Push the gear shaft 4WD through the ball bearing of the large
plastic engine mount 4WD and re-assemble the gear plate at the
clutch flange using M6x40 cylinder screws and Ø6,4 disks.
4. Press steel gearwheel 14 teeth on the gear shaft 4WD as pictured and fix it on the surfaces of the gear shaft 4WD using
M5x5 headless pins, secure with M6x16 countersunk screw and
use a high-strength screw retention (Position 32+34).
Disk
Ø6,4
Screw
M6x40
2. Remove retaining washer Ø7 of the gear shaft from the plastic
gearwheel. Dismount headless pin M5x5 of the brake square and pull
out the 2WD geart shaft from the gear plate. Then press the 4WD
gear shaft through the brake square, gear plate, shim ring 1x16x1
and plastic gearwheel and secure it with retaining washer Ø7. Mount
brake square backlash-free on the surface of the gear shaft 4WD
using the headless pin M5x5.
Gear
plate
Position 33
Parts are in
bag I
Gear
shaft
4WD
Hint: Rinse the existing foam filter (if it is dirty) with rinsing water,
let it dry and oil it again. To oil the foam filter knead it in a plastic
bag with FG filter oil Item N°. 06441 repeatedly.
Shim ring
10x16x1
Plastic
gearwheel
Position 34
Parts are in
bag I
Brake
square
Headless
pin
M5x5
Clutch bell
Retaining
washer Ø7
Headless
pin
M5x5
Retaining
washer Ø7
Steel gearwheel
15 teeth only for
Monster models
Only for Monster models:
Dismount steel geawheel 16 teeth.
Mount steel gearwheel 15 teeth on the clutch bell and
secure with Ø7 retaining washer.
Tighten the steel gearwheel 15 teeth backlash-free on the
surfaces of the clutch bell using headless pins M5x5.
3. Dismount tank from your existing 2WD
model. Fix the tank (tank cap facing the right
side) with tank mount on the tank base using
4,2x16 countersunk screws (longer side of tank
base must face the right side).
4. Mount the tank assembled on tank base on
the alloy chassis using 4,2x16 countersunk
screws.
Position 35
Parts are in
bag I
Screw
4,2x32
Disk
Ø4,3
Tank complete
Tank mount
Engine fixing
disk
Screw
4,2x16
Alloy chassis
Screw
4,2x16
Screw
4,2x16
Tank base
1. Insert the complete engine in the
alloy chassis and fasten it with
4,2x32 pan-head screw and disk
Ø4,3 through the rear axle mount.
Do not tighten the 4,2x32 pan-head
screw yet, see also position 36a.
2. Fix the pre-assembled engine
using 4,2x16 countersunk screws
and engine fixing disks from
underneath on the alloy chassis.
Position 36
Parts are in
bag I
5. Tighten the 4,2x32 pan-head
screws after setting the engine fixing
screws tight.
6. Install the fuel pipes as pictured,
shorten them if necessary.
Position 36a
Parts are in
bag I
Alloy connecting brace
Plastic engine mount
large 4WD
Screw
4,2x32
Disk Ø4,3
Rear axle
mount left
Position 37
Parts are in
bag J
Flexible aerial
Receiver
box
Screw
2,9x13
Collar disk for
rc-plate 4WD
Plastic rc-plate
4WD
Hint: Fill the bottom part of the receiver box 1. Dismount the rc-plate from your existing 2WD
model, remove battery mount, servos and receiver
with some foam to protect the receiver
box.
against vibrations.
2. Mount the throttle/brake servo and the steering servo in the plastic rc-plate 4WD as described in position 37.
3. Fix the receiver box to the plastic rc-plate
Battery mount with
4WD using 2,9x13 pan-head screws, connect
receiver battery
Steering servo
the servo cables, battery cables to the receiver
again and check the function. Now stow the
receiver and the rest of the servo cables in the
receiver box, lead the aerial cable of the receiver
in the flexible aerial.
4. Press the collar disk for the 4WD rc-plate into
Body clip the plastic rc-plate 4WD.
5. Mount the bolts for the battery mounts to the
plastic rc-plate 4WD using 2,9x13 pan-head
screws. Fix the battery mount with receiver battery with body clips to the bolts.
6. Now press the servo arm back on the steering
Bolt for bat- servo as described in position 38 and fix it with
tery mount
enclosed screw. The servo arm should be in a
Screw
90-degree position to the steering servo at neu2,9x13
tral position of the radio control, change the
Gas/brake
servo
position of the servo arm correspondingly.
Screw
2,9x13
Position 38
Parts are in
bag J
Servo
arm
Receiver
box
Position 40
Parts are in
bag J
approx. 108mm
4. Disassemble the track
rods of your existing 2WD
model.
5. Mount the track rods
(collar of the joint ball
must face the servo saver)
to the servo saver by
using M4x20 cylinder
screws and M4 stop nuts.
Servo rods
mounted
Joint
ball
Screw
M4x20
Plastic rc-plate
4WD
Collar disk for
rc-plate 4WD
1. Impress the tension sleeve for servo saver
from above through servo saver part B and
servo saver part A.
2. Mount the servo saver spring with the
M10 nut on the thread of the tension sleeve and check on free movement.
3. Lubricate the servo saver axle slightly
and press it from the top into the tension
sleeve for servo saver. Secure the servo
saver axle with an M5x10 pan-head
screw. Use screw retention lacquer.
Position 39
Parts are in
bag J
Servo saver
axle
Tension sleeve for
servo saver
Servo saver
mounted
Stop nut
M4
Track rod
mounted
Servo
saver
Part A
Servo
saver
Part B
Steel ball
7mm
Ball bearing
7mm
Screw
2,9x19
Rods M4x51
6. Dismount the servo rods from your existing 2WD model
and remove the ball-and-socket joints from the linkage.
7. Screw the ball-and-socket joints 7mm on the rods M4x51
and press the steel balls 7mm into the ball-and-socket joints.
8. Fix the servo rods (collar of the steel ball must face the
servo saver) at the inner hole of the servo saver using 2,9x19
pan-head screws as pictured.
Servo
saver
spring
Nut M10 for
servo saver
Screw
M5x10
Position 41
Parts are in
bag J
Steering servo
Screw
M5x16
Disk
Ø5,3
Front axle
stiffening
Servo
saver
Plastic rc-plate 4WD
Servo rods
Track rod
Alloy chassis
Screw
4,2x16
Stop nut
M4
Dirt, but also longer downtimes can
affect the function and free movement of the servo saver. Therefore we
recommend to spray some penetrating oil between tension sleeve and
servo saver part A+B. Then press servo saver part A downwards against
the spring and check the function. If it
does not function smoothly you have
to dismount and clean the part.
A stiff servo saver can cause a servo
damage.
Screw
2,9x16
Screw
4,2x16
Front upright
left
Disk
Ø4,3
Screw
M4x20
1. Mount the plastic rc-plate 4WD underneath the front axle stiffening to the alloy chassis using 4,2x16 countersunk screws.
2. Now mount the servo saver underneath the plastic rc-plate
4WD by using M5x16 pan-head screw and Ø5,3 disk as pictured. Use screw retention lacquer.
Position 42
Parts are in Screw
bag J
M5x16
Disk
Ø5,3
Front axle
stiffening
Servo
saver
Plastic rcplate 4WD
Track rod
Position 43
Parts are in
bag J
Disk
Ø4,3
Front upright
left
Screw
M4x20
Stop nut
M4
3. Switch on the remote control system, set the trimming of
the steering to central position. Adjust the servo saver in
centre to the chassis. First mount one servo rod to the
servo arm of the steering servo using a 2,9x16 pan-head
screw, then mount the second servo rod. Both servo rods
should be adjusted in the same length. You should be able
to mount both servo rods easily and without any resistance
to the servo arm of the steering servo using 2,9x16 panhead screws, position 41-43.
4. Mount the track rods to the front uprights by using M4x20
cylinder screws, Ø4,3 disks and M4 stop nuts as described
in position 43.
Position 44
Parts are in
bag K
Position 45
Parts are in
bag K
1. Mount the throttle rods to the carburetor arm using
collets and M3x3 headless pins as described in position 45. Keep some clearance between the collets and
the carburetor arm. Make sure the carburetor arm can
be easily moved and does not jam.
Carburetor
arm
Headless
pin M3x3
Headless
pin M3x3
Collet
Collet
tle
rot
Th
s
rod
s
rod
ke
a
r
B
2. Push the M3x25 pan-head screw from the bottom
into the servo arm as described in position 46 and
secure it with an M3 nut. Screw on two M3 stop nuts
as distance. Switch on the remote control system and
set the trimming for throttle/brake in central position.
Press the servo arm on the the servo as pictured in
position 46 and fix it with enclosed screw.
Position 46
Parts are in
bag K
Screw
M3x25
Stop
nut M3
Headless
pin
M3x3
Throttle rods
Throttle pivot
post
Collet
3. Push the collet, pressure spring, throttle pivot post
and collet on the throttle rods. In doing so, press the
throttle pivot post on the M3x25 pan-head screw and
secure it with an M3 stop nut. Fix the collets using
M3x3 headless pins. See position 46.
Switch on the remote control system. Set the servo for
throttle/brake in central position. Now clamp the collet
to the throttle pivot post using an M3x3 headless pin.
Set the transmitter to full throttle position and check if
the carburetor arm opens completely.
Tipp: Do not tighten the M3 stop nut at the throttle
pivot post. The throttle pivot post and the throttle rods
must run smoothly, move easily and should neither
touch nor clamp in any position.
Steering servo
Pressure spring
Stop
nut M3
Nut
M3
rods
Brake
Servo
arm
Throttle/brake
servo
Collet
Headless pin
M3x3
Monster/Stadium models
Position 47
Parts are in
bag K
1. Dismount roll bar and reinforcing brace from your existing 2WD
model.
2. Mount the plastic parts for the reinforcing braces at the roll bar
again using 4,2x32 pan-head screws as pictured. Push the reinforcing
Spoilerhalter
braces
into the plastic parts for the braces at the front shock mount
and fix them using 2,9x9,5 pan-head screws.
Kunststoff
strebe kurz
Screw
2,9x9,5
Reinforcing brace
Scheibe
Plastic part for
Ø4,3
reinforcing brace
Schraube
4,2x13
Auspuffrohr
Halterung für
Auspuffrohr
Schraube
4,2x22
Roll bar
Dämpferplatte
hinten 4WD
Baustufe 50
Alloy chassis
Teile sind in
Beutel
Schraube
M6x75
Baja
Screw
4,2x16
3. Mount the roll bar to the alloy chassis
Reinforcing brace
Screw
4,2x32
Screw
2,9x9,5
Screw
2,9x9,5
Plastic part for
reinforcing brace
1. Disassemble the left and right alloy side plates from your existing 2WD model and mount them to
the alloy chassis using M4x8 pan-head screws. Fix the left and right alloy side plates to the front
shock mount using 4,2x16 pan-head screws, Ø4,3 disks and plastic bushes 4/6x5.
2. Fasten the left alloy side plate with M6x75 cylinder screw, Ø6,4 disk and alloy distance 10x34.
3. Fasten the right alloy side plate with M4x45 cylinder screw, Ø4,3 disk and alloy distance 8x27.
4. Dismount the complete rear spoiler mount from your existing 2WD model and fix it at the rear shock
mount 4WD by using M4x20 cylinder screws and M4 stop nuts. Spoiler mount and rear body mounts
can differ for Hummer, Jeep and Beetle Pro models.
5. Mount the long plastic braces with 4,2x32 pan-head screws and roll bar.
Position 48
Plastic brace
long
Screw
4,2x32
Monster/Stadium models
Roll bar
Alloy side
plate right
Plastic
bush
4/6x5mm
Disk
Ø4,3
Screw
4,2x16
Allloy distance
10x34
Alloy side
plate left
Alloy chassis
Side body
mount
Screw
M4x8
Screw
M4x8
Disk Ø6,4
Cylinder screw
M6x75
If necessary file the boring to a long slot.
Treat the other side in the same way.
If necessary file the side plates here slightly to
make sure the track rods do not pile while
steering. Treat the other side in the same way.
Mount exhaust pipe from your
existing 2WD model.
Position 49
Parts are in
bag K
n
tio
ec ja
t
o a
pr r B
ug fo
Pl nly
o
Plastic part for
reinforcing brace
only for Baja
Roll bar
Plastic
Plastic
brace short
brace long
Screw
Rear body
4,2x22
mount only for
Baja
Spoiler mount
Screw
4,2x13
Marder/
Baja Buggy
Screw
M4x8
Allo
y ch
ass
is
Rocker
panel left
Screw
M4x8
Rear damper
plate 4WD
1. Dismount the left and right rocker panels from your existing
2WD model and fix them to the alloy chassis by using M4x8 panhead screws.
2. Remove the complete rear spoiler mount from your existing
2WD model and fix it at the rear 4WD shock mount using M4x20
cylinder screws and M4 stop nuts.
3. Mount the long plastic braces with M4x50 headless pins (for
Marder only with 4,2x32 pan-head screws) and plastic parts for
reinforcing brace to the roll bar.
Screw
M4x20
Alloy cover
Screw
2,9x9,5
Position 50
Parts are in
bag K
Long alloy
brace Baja 4WD
Screw
2,9x9,5
Baja Buggy
1. Dismount the front roll bar from your existing
2WD model.
2. Remove screws 2,9x9,5 from the alloy cover
and front alloy plate. Dismount front roll bar
parts and plastic braces for cover.
3. Mount the front roll bar parts and the plastic
braces for the cover to the long alloy braces
Baja 4WD, then push the complete part into the
plastic part for stiffening brace and in the front
plastic fixing plate as described in position 50.
4. Bore out the front alloy plate and the alloy
cover with a 2,5mm drill as pictured and fix
them to the long alloy braces 4WD Baja by
using 2,9x9,5 pan-head screws.
Front plastic
fixing plate
Drill 2,5mm
Plastic brace for
cover
Front
alloy plate
Position 51
Parts are in
bag K
Front part
roll bar
Plastic part for stiffening brace
Position 52
Hummer
Drill 9mm hole
for aerial
Cut out the left and right wheel cases of the
rear bodyshell a little more with a scissors to
prevent the bodyshell from rubbing against
the wheels.
Even the cut borders slightly
with an emery cloth.
Position 53
Baja Buggy
Cut out the left and right wheel cases of the front bodyshell a little more as pictured by using a scissors or a
model knife to prevent the bodyshell from rubbing
against the wheels.
Cut out the openings for the
track rods as marked on the illustration a little more by using a
scissors or a model knife to prevent the track rods from rubbing
against the bodyshell.
Drill 9mm hole
for aerial
Cut out an opening for the tank cap by using a
scissors or a model knife.
Position 54
Drill 9mm hole
for aerial
Monster Truck
Cut out the left and right wheel cases of the
front bodyshell a little more as pictured by
using a scissors or a model knife to prevent
the bodyshell from rubbing against the wheels.
Position 55
Jeep
Jeep
Drill new 9mm hole
for aerial
Cut out the left and right wheel cases of
the front and rear bodyshell a little more
as pictured by using a scissors or a
model knife to prevent the bodyshell
from rubbing against the wheels.
Position 56
Marder
Marder
Cut out an opening on the right
side of the bodyshell for receiver
box respectively flexible aerial.
Remove the front and rear body part by
using a scissors or a model knife. Cut out
the bodyshell a little more within the area
of the track rods.
Marder
Cut out an opening on the left
side of the bodyshell for servo
arm respectively the brake rods.
Exploded view for
1:6 BAJA BUGGY 4WD
1:6 MARDER OFF-ROAD BUGGY 4WD
06087/01
06087
08523 Set/Kit
06093
66305
66304
06086
06089
06445
68140/02
06421/05
06088
07091
68140/01
68150/01
06093
06732/03
06093 06088
06092
07087/01
68155
06714/19
06022/01
60215/05
06714/13
06714/09
06714/09
06540
60236
60237
8
28
66
09
4/
71
6
0
66200
05718/16
06734/04
60235
3
23
3
60
01
06
06738/04
06738/04
06731/08
54
662
06722/30
06733/06
06734/06
06714/16
68323
06714/19
08
29/
060
06714/13
06081/01
06112
66245
01
26/
68323 060
66244
01
28/
060
5
34/0
067
66230
60230
04
38/
067
30
060
68271
68270
68327
0
25/2
067
06029/07
06730/16
06078/05
68277
06730/25
5
32/0
067
71
662
67
662
06731/08
65
682
1
50/0
662
68324
68266
68
682
06734/05
06712/16
07102
06712/16 07100
76
682
6
16/1
067
06726/16
06712/16
66255
50
682
06069/01
06731/08
06013
5
63/0
060
06066/02
06734/04
52
682
57
662
64
060
06067/02
06068
06725/14
53
682
16
12/
067
08523
66305
06011
06013
54
662
66286
66285
04
34/
067 8/04
3
067
30
25/
067
06739/04
06734/04
58
662
56
662
40
20/
067
25
20/
067
66285/01
51
682
93
080
66287
68240
06029/07
06734/04
68325
68326
06725/20
06738/06 06081/01
06030
06738/04
06735/10
06712/13
06451/03
07384
06712/16
06464/04
66218/01
06464/05
8
30/0 5
073
34/0
067
06465/01
06465-Set
06451/04
FG Modellsport GmbH
Spanningerstr. 2
Phone: +49 7181 9677-0
Fax: +49 7181 9677-20
01
37/
061
07329/01
5 06038 06712/16
38/0 1
7
6
0
06723/16
34/0
07332
061
66217
13
/
6
1
06728/03
067
08345
11
06020
06730/05
662
06726/40
06716/32
07331/06
6
4
3
2
06734/04
68
8/0
06728/03
06727/10
06738/03 0672020
06036/05
07315
6
0
06020
1
3
06728/03
16/1 6037/0
26
68216
1
7
6
6
0
0
0
06020
/08
06724
06738/03
5
1
06039/07
2
68
06739/03
06730/05 06045/03
06534/02
07315/01
06038
07316
06042/01
6
39/0
05019/01
06724/08
060
07317/11
06044/01
06732/05
07318
06036/05
06045/01
08456
06745
06049/01
06051
06734/06
06040/05
06724/18
06050
06137/01
06727/40
06730/05
06432
06732/07
06427
06732/07
06725/20
60238
66210
60239/01
06013
04
34/
067
06716/22
60239
06034/01 06729/50
06730/30
06712/13
66236
66235
06013
60240
06725/20
66258
06
682
06712/16
06033
66207
06738/04
06738/04
66208
06067/02
68213
06720/40
06068
21
682
06738/05
06029/08
12
662
16
12/
067
06726/25
06734/04
06731/14
06722/35
60209/05
06077
66226
06712/16
07348
06712/16
06080
06078/05
06077/08
06734/05
06078/05
68220
66238/02
66304
06729/30
66222
66223
07352
08523
06069/01
06073
06732/05
68225
07353
06739/05
06738/05
06072/02
06036/05
06350
06712/16
68205
03
00/
061
75
060
07351
01
38/
662
06063/05
30
22/ 06
067
081
067
32/0
/01
067
5
34/0
5 100
07
37
662
06066/02
06081/01
05
38/ 06722/25
067
06029/08
00
662
06716/22
06064
067
30/2
5
31
060
06077/05
06029/08
06733/06
06079
06734/06
66230
06738/06
06112
Spare parts list for 68040R - 68050R
1:6 BAJA BUGGY 4WD
1:6 Marder Off-Road Buggy 4WD
Bolt for battery holder, 2pcs.
Pressure spring 0,4x5x25mm, 2pcs.
Side guards l./r. each, 1pce.
Body clips, 10pcs.
Collets 2,1 mm, 5pcs.
Flexible aerial and mount, 1pce.
Rods M4 x 51mm, 2pcs.
Track rod right/left 1:6, 74mm, 2pcs.
Ball-and-socket joint for M6, 4pcs.
Steel balls 10 x 10,75, 4pcs.
Roll cage, 1pce.
Wing mount, 1pce.
Plastic part f. stiffening brace, 2pcs.
FG ball bearing 10x19x7 w. grease fill., 2pcs.
Steel fixing plates, 2pcs.
Engine mount washers, 4pcs.
Gear plate 06, 1pce.
GRP brake plate, 1pce.
Brake square 97, new 1pce.
Brake disk epoxy 97, new 1pce.
Brake operating shaft 97, new each 1pce.
Brake lever 30mm, 1pce.
Clutch bell, 1pce.
Plastic gear carrier 60 mm, 1pce.
Dampening rubber, 4pcs.
FG ball bearing 12x28x8w. grease filling, 2pcs.
Differential housing, 1pce.
Diff. gearwheel A reinforced, 2pcs.
Diff. gearwheel B reinforced, 2pcs.
Bevel differential gear axle, 1pce.
Diff.driving axle, pluggable, 1pce.
Adj. rear lower wishbone Monster, 1pce.
Rear lower wishbone pin, 2pcs.
Rear upper wishbone pin, 2pcs.
Rear upright raised l./r., 2pcs.
Steel ball 10x13 for rear upright, 2pcs.
Distance bush for rear upright, 2pcs.
FG ball bearings 8x22x7 w. grease filling, 2pcs.
Rear driving axle, 1pce.
Rear dogbone, 1pce.
Ball 5/10x15 M5, 4pcs.
Rear shock absorber housing, 1pce.
Upper shock plug M4, 2pce.
Lower shock plug A+B, 2pcs.
Shock piston 2-hole, 2pcs.
Spring plate, 2pcs.
Shock seal kit, 4pcs.
Turnbuckle right/left, 36 mm, 2pcs.
M6 nuts with disk, 10pcs.
Brake rods compl./1:6, set
Engine mount small/G230 RC/Marder, 1pce.
Bolt f. gear unit 24,5/26,5mm, 3pcs.
Battery holder, 1pce.
Fuel tube, 1pce.
Polycarbonate rear spoiler f.1:6 OR, 1pce.
Plastic gearwheel 46 teeth, 1pce.
Steel gearwheel 18 teeth, 1pce.
Shock absorber collet, 8pce.
Air filt. adapt.f. Zen.G230/G260,CY23/26, 1pce.
O-rings f. air filter adapt.19x1,5/ 57x2,5 , 2pcs.
Foam filter oiled, 2pcs.
FG inlet air filter 1:6 OR complete, set
Filter cover, 1pce.
Item N°. Description
05014/05
05019/01
06011
06013
06020
06022/01
06026/01
06028/01
06029/07
06029/08
06030
06031
06033
06034/01
06036/05
06037/01
06038
06039/06
06039/07
06040/05
06042/01
06044/01
06045/01
06045/03
06049/01
06050
06051
06063/05
06064
06066/02
06067/02
06068
06069/01
06072/02
06073
06075
06077
06077/05
06077/08
06078/05
06079
06080
06081/01
06086
06087
06087/01
06088
06089
06092
06093
06100/03
06112
06126
06134/01
06137/01
06268
06350
06421/05
06427
06432
06445
06451/03
06451/04
06464/05
06465
06465/01
Oil for shock absorber 2000, 1pce.
Throttle pivot post 2,1 mm, set
Receiver box, 1pce.
FG receiver battery NiCd 6V/1500mAh, 1pce.
Single storage batt. NiCd 1,2V/800mAh, 4pcs.
Charger 220V/Fut., Hitec, 1pce.
Counters.sh.met.screws,4.2x13mm,20pcs.
Counters.sh.met.screws,4.2x16mm,20pcs.
Pan-head tap.screws, 2.9x9.5mm, 15pcs.
Pan-head tap.screws, 2.9x13mm, 15pcs.
Pan-head tapping screw 2,9x16mm, 15pcs.
Pan-head tapping screw 2,9x19mm, 15pcs.
Rec. counters.head screws,M4x25mm,10pcs.
Rec.counters.head screws,M4x40mm,10pcs.
Rec.counters.head screws,M6x16mm, 10pcs.
Socket head cap screws 8.8,M3x8mm,10pcs.
Sock. head cap screws 8.8,M3x18mm,10pcs.
Socket head cap screws M4x14mm,10pcs.
Socket head cap screw M4x20mm, 10pcs.
Sock. head cap screws 8.8,M6x40mm, 5pcs.
Headless pin M3x3mm, 15pcs.
Headless pin M4x30, 15pcs.
Headless pin M4x50, 8pcs.
Tallow-drop screw M4x8mm, 15pcs.
Retain.washers-spring steel,3.2mm, 15pcs.
Retain.washers-spring steel, 5mm, 15pcs.
Headless pin, M6x6mm, 15pcs.
Washers, steel 4.3mm, 15pcs.
Pan-head cap screw M5x10, 10pcs.
Self-locking hexagon nut, M3, 15pcs.
Hexagon nut M3, 15pcs.
Shim rings 10x16x1mm, 10pcs.
Body screws, 15pcs.
Lower shock retaining, short 2pcs.
Shock piston shaft long, 1pce.
Adjusting clips for front axle 16pcs.
Front wishbone pin, 2pcs.
Clutch block carrier, 1pce.
Screw for carrier/Zenoah, 1pce.
Clutch blocks, 2pcs.
Clutch spring Ø G230/240/260/270, 1pce.
Dowel screws f.clutch blocks/Zenoah, 2pcs.
Metal coating for standard plug cap, 1pce.
Silencer f. Marder/Zenoah, 1pce.
Scews f. silencer M5x60, 2pcs.
Silicone tube 14x3x40, 2pcs.
Silencer gasket, 2pcs.
Tank complete/Zenoah, 1pce.
06510/20
06534/02
06540
06546
06546/04
06548
06712/13
06712/16
06714/09
06714/13
06714/16
06714/19
06716/13
06716/16
06716/22
06716/32
06720/25
06720/40
06722/25
06722/30
06722/35
06723/16
06724/08
06724/18
06725/14
06725/20
06726/16
06726/25
06726/40
06727/10
06727/40
06728/03
06729/30
06729/50
06730/05
06730/16
06730/25
06730/30
06731/08
06731/14
06732/03
06732/05
06732/07
06733/06
06734/04
06734/05
06734/06
06735/10
06738/03
06738/04
06738/05
06738/06
06739/03
06739/05
06745
07058
07087/01
07091
07100
07102
07315
07315/01
07316
07317/11
07318
07328/05
07329/01
07330/08
07331/06
07332
07348
Fuel tube/Zenoah, 1pce.
Rubber gasket f. tank, 1pce.
FG Zenoah engine G260RC
Hitec RCS Aggressor FM/DCX receiver, set
Brake guide rail, 1pce.
Coupling flange Zenoah 1:6, 1pce.
Steel brake plates, 2pcs.
Rear shock absorber set, long, 2pcs.
Baja tires S wide glued, 2pcs.
Baja tires M narrow glued, 2pcs.
Front bumper Baja, 1pce.
Roll cage parts front, 2pcs.
Front alloy plate, 1pce.
Alloy cover, 1pce.
Plastic brace for cover, 2pcs.
Plug protection, 1pce.
Plastic brace long, 2pcs.
Plastic brace short, 2pcs.
Rear body mount Baja, 2pcs.
Model sticker f. Baja Buggy 4WD comp., set
Alloy chassis 4WD, 1pce.
Plastic gear disk rear 42t. 4WD, 1pce.
Steel gear wheel 48t. 4WD, 1pce.
Rear axle cover 4WD, 1pce.
Gear wheel protection 4WD, 1pce.
Alloy connection rod gear 4WD, 1pce.
Steel gear wheel 14t. narrow, 1pce.
Basic body f. inlet silencer, 1pce.
Bear.shaft f. tension. pulley housing 4WD,1pce.
Plastic bearing seat 4WD, 2pcs.
Wishbone thread rod M10/M8x84mm, 2pcs.
Alloy square wheel driver 14mm/M6, 2pcs.
Lower part belt channel, 1pce.
Upper part belt channel, 1pce.
Toothed belt, 1pce.
Lower tank mount 4WD, 1pce.
Upper tank mount 4WD, 1pce.
Ball-and-socket joint 7mm f.M4, 8pcs.
Steel ball 7mm, 4pcs.
Guide f. front stabi 4mm 4WD, 2pcs.
Bearing shaft, 6x50mm, 1pce.
Ball bearing 6x15x5, 4pcs.
Front plastic toothed belt wheel 42t. 4WD,1pce.
Front plastic stop disk left 4WD, 1pce.
Plastic stop disk right 4WD, 1pce.
Reinforcing plate f. front axle Baja 4WD, 1pce.
Alloy distance SW 10x7, 2pcs.
Plastic fixing plate front Baja 4WD, 1pce.
Front alloy shock mount Baja 4WD, 1pce.
Alloy brace long Baja 4WD, 2pcs.
Damper press. spring blue 2,1x100mm, 2pcs.
Damper press. spring violet 2,2x100mm, 2pcs.
Body Baja Buggy 4WD painted, 1pce.
Rear Spoiler Baja Buggy 4WD painted, 1pce.
Body Baja Buggy 4WD clear, 1pce.
Plastic rear axle mount left 4WD, 1pce.
Plastic rear axle mount right 4WD, 1pce.
Plastic damper plate rear 4WD, 1pce.
Plastic engine mount large 4WD, 1pce.
Gear shaft 4WD, 1pce.
Hous. f. plastic tension. pulley left 4WD, 1pce.
Hous. f. plastic tension. pulley right 4WD, 1pce.
Rear upper plastic wishbone 4WD, 2pcs.
Plastic RC-plate 4WD, 1pce.
Throttle rods 4WD compl., set
Plastic front axle housing left 4WD, 1pce.
Plastic front axle housing right 4WD, 1pce.
Plastic toothed belt wheel 12t. 4WD, 1pce.
Plastic deflection roller 16mm, 1pce.
07352
07353
07384
07561
08093
08345
08456
08523
60209/05
60215/05
60230
60233
60235
60236
60237
60238
60239
60239/01
60240
66155
66200
66207
66208
66210
66211
66212
66217
66218/01
66222
66223
66226
66230
66235
66236
66237
66238/01
66238/02
66244
66245
66250/01
66254
66255
66256
66257
66258
66267
66271
66285
66285/01
66286
66287
66288
66304
66305
68140/01
68140/02
68150/01
68205
68206
68213
68215
68216
68220
68221
68225
68240
68246
68250
68251
68252
68253
Front lower plastic wishbone 4WD, 1pce.
Front upper plastic wishbone 4WD, 2pcs.
Front lower wishbone pin 106mm, 2pcs.
Front plastic upright 4WD, 2pcs.
Fixing nut f. front upright, 2pcs.
Front driving axle 4WD, 1pce.
Front driving shaft 4WD, 1pce.
Servo saver A/B, 1pce.
Servo saver axle new, 1pce.
Servo saver spring 2,0mm, 4WD, 1pce.
Nut M10 f. servo saver, 1pce.
Tension sleeve f.servo saver new, 1pce.
68265
68266
68268
68270
68271
68276
68277
68323
68324
68325
68326
68327
05014/05
05019/01
06013
06020
06022/01
06026/01
06028/01
06029/07
06029/08
06030
06031
06033
06033/01
06034
06034/01
06036/05
06037/01
06038
06039/11
06039/12
06040/05
06042/01
06044/05
06045/01
06045/03
06047/01
06049/01
06050
06051
06052
06063/05
06064
06066/02
06067/02
06068
06069/01
06072/02
06073
06075
06077
06077/05
06077/08
06078/05
06079
06080
06081/01
06086
06087/01
06088
06089
06092
06093
06100/03
06112
06126
06134/01
06137/01
06175
06176
06183
06183/01
06183/02
06183/03
06184
Bolt for battery holder, 2pcs.
Pressure spring 0,4x5x25mm, 2pcs.
Body clips, 10pcs.
Collets 2,1 mm, 5pcs.
Flexible aerial and mount, 1pce.
Rods M4 x 51mm, 2pcs.
Track rod right/left 1:6, 74mm, 2pcs.
Steel balls 10 x 10,75, 4pcs.
Roll cage, 1pce.
Wing mount, 1pce.
Body support, 1pce.
Stiffening brace f. Monster Truck, 2pcs.
Plastic part f. stiffening brace, 2pcs.
Steel fixing plates, 2pcs.
Engine mount washers, 4pcs.
Gear plate 09, 1pce.
GRP brake plate, 1pce.
Brake square 97, new 1pce.
Metal brake disk, 1pce.
Brake operating shaft 97 new, each 1pce.
Brake lever 30mm, 1pce.
Steel gearwheel 15theeth widened, 1pce.
Clutch bell, 1pce.
Plastic gear carrier 60 mm, 1pce.
Dampening rubber, 4pcs.
FG ball bearing 12x28x8w. grease fill., 2pcs.
Differential housing, 1pce.
Diff. gearwheel A reinforced, 2pcs.
Diff. gearwheel B reinforced, 2pcs.
Bevel differential gear axle, 1pce.
Diff. driving axle, pluggable, 1pce.
Adj. rear lower wishbone Monster, 1pce.
Rear lower wishbone pin, 2pcs.
Rear upper wishbone pin, 2pcs.
Rear upright raised l./r., 2pcs.
Steel ball 10x13 for rear upright, 2pcs.
Distance bush for rear upright, 2pcs.
FG ball bearings 8x22x7 w. grease fill., 2pcs.
Rear driving axle, 1pce.
Rear dogbone, 1pce.
Ball 5/10x15 M5, 4pcs.
Rear shock absorber housing, 1pce.
Lower shock plug A+B, 2pcs.
Shock piston 2-hole, 2pcs.
Spring plate, 2pcs.
Shock seal kit, 4pcs.
Turnbuckle right/left, 36 mm, 2pcs.
M6 nuts with disk, 10pcs.
Brake rods compl./1:6, set
Engine mount small/G230 RC/Marder, 1pce.
Bolt f. gear unit 24,5/26,5mm, 3pcs.
Body support Monster models, 1pce.
Dampening rubber f. body support, 4pcs.
Left alloy side plate, 1pce.
Alloy distance 8x27/ 10x34, 2pcs.
Socket head cap screw M6x75mm, 1pce.
Right alloy side plate, 1pce.
Spare parts list for 1:6 Monster Truck,
Monster Hummer, Monster Jeep 4WD/
1:6 Stadium Truck, Stadium Hummer,
Stadium Jeep 4WD
Shim rings 10x16x1mm, 10pcs.
Body screws, 15pcs.
Stabilizer 5mm rear, 1pce.
Plastic brace f.stabilizer long, 6pcs.
Lower shock retaining, short 2pcs.
Shock piston shaft long, 1pce.
Adjusting clips for front axle 16pcs.
Front wishbone pin, 2pcs.
Body mount adjustable, 1pce.
Body mount adjustable 80mm, 1pcs.
Body mount short, adjustable, 1pce.
Clutch block carrier, 1pce.
Screw for carrier/Zenoah, 1pce.
Clutch blocks, 2pcs.
Clutch spring Ø G230/240/260/270, 1pce.
Dowel screws f.clutch blocks/Zenoah,2pcs
Metal coating for standard plug cap, 1pce.
Scews f. silencer M5x60, 2pcs.
Silencer, 1pce.
Exhaust pipe bended, 1pce.
Silicone tube 14x3x40, 2pcs.
Mount for exhaust, 1pce.
Silicone tube f. 7331/7, 2pcs.
Silencer gasket, 2pcs.
Tank complete/Zenoah, 1pce.
Fuel tube/Zenoah, 1pce.
Rubber gasket f. tank, 1pcs.
FG Zenoah engine G260RC
Hitec RCS Aggressor FM/DCX receiver, set
Coupling flange Zenoah 1:6, 1pce.
Steel brake plates, 2pcs.
Plastic bush 4/6x5mm, 4pcs.
Rear shock absorber set, long, 2pcs.
Body Monster/Stadium Truck 4WD white, 1pce.
Front body Monst./Stad./Street Truck white,1p.
Body Monster/Stadium Truck 4WD yellow, 1pce
Front body Monst./Stad./Street Truck yellow,1p.
Body Monst/Stad./ Truck 4WD transparent, 1p.
Front body Monst./Stad./Str.Truck transp., 1pc.
Model stickers f.Monster/Stad. Truck 4WD, set
Body Monster/Stadium Hummer H2 yellow,1p.
Body Monster/Stadium Hummer H2 black, 1p.
Body Monster/Stadium Hummer H2 transp.,1p.
Model stickers for Hummer H2 4WD, set
Body Monster/Stadium-Jeep 4WD, red, 1pce.
Body Monster/Stadium-Jeep 4WD, black, 1pce.
Body Monster/Stadium Jeep 4WD transp.,1p.
Model stickers for Jeep 4WD, set
Front bumper Baja, 1pce.
Plastic brace long, 2pcs.
Plastic brace short, 2pcs.
Alloy chassis 4WD, 1pce.
Plastic gear disk rear 42t. 4WD, 1pce.
Steel gear wheel 48t. 4WD, 1pce.
Rear axle cover 4WD, 1pce.
Gear wheel protection 4WD, 1pce.
Alloy connection rod gear 4WD, 1pce.
Steel gear wheel 14t. narrow, 1pce.
Basic body f. inlet silencer, 1pce.
Bearing shaft f.tension. pulley housing 4WD,1p.
Plastic bearing seat 4WD, 2pcs.
Alloy square wheel driver 14mm/M6, 2pcs.
Square wheel driver 14mm/M6 steel, 2pcs.
Lower part belt channel, 1pce.
Upper part belt channel, 1pce.
Toothed belt, 1pce.
Lower tank mount 4WD, 1pce.
Upper tank mount 4WD, 1pce.
Ball-and-socket joint 7mm f.M4, 8pcs.
Steel ball 7mm, 4pcs.
06745
07058
07071/01
07071/02
07087/01
07091
07100
07102
07154
07154/01
07155
07315
07315/01
07316
07317/11
07318
07328/05
07330/08
07331/03
07331/04
07331/06
07331/07
07331/08
07332
07348
07352
07353
07384
07561
08345
08456
08462/01
08523
26100/01
26100/02
26110/01
26110/02
26150/01
26150/02
26155
36110
36130
36150
36155
46120
46130
46150
46155
60230
60239
60239/01
66200
66207
66208
66210
66211
66212
66217
66218/01
66222
66223
66226
66230
66230/05
66235
66236
66237
66238/01
66238/02
66244
66245
06185
06227/07
06228/07
06230/07
06231/07
06268
06350
06427
06432
06445
06451/03
06451/04
06464/05
06465
06465/01
06510/20
06534/02
06540
06546
06546/04
06548
06565/29
06712/13
06712/16
06712/32
06714/09
06714/13
06714/16
06714/19
06716/09
06716/13
06716/16
06716/22
06716/32
06720/40
06722/25
06722/30
06722/35
06723/16
06724/08
06724/16
06724/18
06725/14
06725/20
06726/16
06726/25
06726/40
06727/10
06727/40
06728/03
06729/30
06730/05
06730/16
06730/25
06730/30
06731/08
06731/14
06732/03
06732/05
06732/07
06733/06
06734/04
06734/05
06734/06
06735/10
06738/03
06738/04
06738/05
06738/06
06739/03
06739/05
Side body mounts, 2pcs.
Monster Truck tires S 14mm glued, 2pcs.
Monster Truck tires M 14mm glued, 2pcs.
Stadium Truck tires M/14mm glued, 2pcs.
Stadium Truck tires S/14mm glued, 2pcs.
Battery holder, 1pce.
Fuel tube, 1pce.
Steel gearwheel 18 teeth, 1pce.
Shock absorber collet, 8pce.
Air filt. adapt.f. Zen.G230/G260,CY23/26, 1pce.
O-rings f. air filter adapt.19x1,5/ 57x2,5 , 2pcs.
Foam filter oiled, 2pcs.
FG inlet air filter 1:6 OR complete, set
Filter cover, 1pce.
Oil for shock absorber 2000, 1pce.
Throttle pivot post 2,1 mm, set
Receiver box, 1pce.
FG receiver battery NiCd 6V/1500mAh, 1pce.
Single storage batt. NiCd 1,2V/800mAh, 4pcs.
Charger 220V/Fut., Hitec, 1pce.
Cable clamps black, 4.8x290mm, 25pcs.
Counters.sh.met.screws 4.2x13mm, 20pcs.
Counters.sh.met.screws 4.2x16mm, 20pcs.
Counters.sh.met.screws 4,2x32mm, 20pcs.
Pan-head tap.screws 2.9x9.5mm, 15pcs.
Pan-head tap.screws 2.9x13mm, 15pcs.
Pan-head tap.screws 2,9x16mm,15pcs.
Pan-head tap.screws 2,9x19mm, 15pcs.
Pan-head tap.screws 4,2x9.5mm, 15pcs.
Rec.counters.head screws M4x40mm,10pcs.
Rec.counters.head screws M6x16mm, 10pcs.
Sock. head cap screws 8.8,M3x8mm,10pcs.
Sock. head cap screws M3x16mm,10pcs.
Sock. head cap screws 8.8 M3x18mm,10pcs.
Socket head cap screws M6x10mm, 5pcs.
Socket head cap screws 8.8,M6x40mm, 5pcs.
Retain.washers-spring steel,3.2mm, 15pcs.
Headless pin, M6x6mm, 15pcs.
Pan-head cap screw M5x10, 10pcs.
66250/01
66254
66255
66256
66257
66258
66267
66271
66284
66287/01
66287/02
66291/05
66304
66305
68205
68206
68213
68215
68216
68220
68221
68225
68241
68246
68250
68251
68252
68253
68265
68266
68268
68270
68271
68276
68277
68323
68324
68325/01
68326
68327
Guide f. front stabi 4mm 4WD, 2pcs.
Bearing shaft, 6x50mm, 1pce.
Front plastic toothed belt wheel 42t. 4WD,1pce.
Front plastic stop disk left 4WD, 1pce.
Plastic stop disk right 4WD, 1pce.
Reinforcing plate f.fr.-axle Monst./Stad.4WD,1p.
Front shock mount Monster/Stadium 4WD, 1p.
Lower shock retaining, long 4WD, 2pcs.
Damper pressure spring blue 2,1x100mm,2pcs.
Dampfer pressure spring violet 2,2x100mm,2p.
Plastic rear axle mount left 4WD, 1pce.
Plastic rear axle mount right 4WD, 1pce.
Plastic damper plate rear 4WD, 1pce.
Plastic engine mount large 4WD, 1pce.
Gear shaft 4WD, 1pce.
Housing f. plastic tensioning pulley left 4WD,1p.
Housing f.plastic tensioning pulley right 4WD,1p
Rear upper plastic wishbone 4WD, 2pce.
Plastic RC plate 4WD f. 9960MG, 1pce.
Throttle rods 4WD compl., set
Plastic front axle housing left 4WD, 1pce.
Plastic front axle housing right 4WD, 1pce.
Plastic toothed belt wheel 12t. 4WD, 1pce.
Plastic deflection roller 16mm, 1pce.
Front lower plastic wishbone 4WD, 1pce.
Front upper plastic wishbone 4WD, 2pcs.
Front lower wishbone pin 106mm, 2pcs.
Front plastic upright 4WD, 2pcs.
Fixing nut f. front upright, 2pcs.
Front driving axle 4WD, 1pce.
Front driving shaft 4WD, 1pce.
Servo saver A/B, 1pce.
Servo saver axle new, 1pce.
Servo saver spring 2,4mm, 1pce.
Nut M10 f. servo saver, 1pce.
Tension sleeve f.servo saver new, 1pce.
1:6 MONSTER/STADIUM TRUCK/ HUMMER/ JEEP 4WD
Exploded view for
1:6 Monster Truck, Monster Hummer, Monster Jeep 4WD
1:6 Stadium Truck, Stadium Hummer, Stadium Jeep 4WD
26100/01
26110/01
26150/01
36110
36130
36150
26100/02
26110/02
26150/02
46120
46130
46150
36155
26155
46155
2
6/3
71
06
06230/07
06714/09
75
061
32
12/
067
06183/01
4
18
06
06716/13
8
1/0
73
06
16
16/
067
06714/09
06734/04
08462/01
01
34/
060
07155
Hummer/Jeep
06185
Truck
4
03
06
06716/16
06176
1
4/0
03
6
0
06183/03
06734/04
3
01
06
8
1/0
73
06
68241
66200
06013
06183/01
16
16/
067
07154/01
Hummer
66287/01
06738/05
68251
58
662
56
662
08523
06183/02
84
662
02
87/
662
05
39/
067
07154
Truck/Jeep
06738/04
66305
68324
07100
06730/16
06730/25
01
28/
060
06733/06
06734/06
06112
68323
06714/19
08
29/
060
06714/13
06714/16
06029/07
67
662
65
682
06081/01
66245
1
6/0
68323 602
0
66244
06722/30
66230
60230
68327
0
25/2
067
5
4/0
73
06
68271
68270
06714/09
68266
5
32/0
067
71
662
06078/05
68277
06022/01
07102
04
38/
067
30
060
76
682
50
682
01
69/
060
06731/08
13
14/
067
19
14/
067
06734/05
55
662
06712/16
68
682
1
50/0
662
06712/16
54
662
64
060
16
12/
067
6
16/1
067
53
682
5
63/0
060
06066/02
07
28/
062
40
065
06726/16
54
662
40
20/
067
57
662
14
25/ 06067/02
067
06068
06734/04
52
682
06183
68325/01
06029/07
06734/04
68326
06725/20
06738/06 06081/01
06030
06738/04
06735/10
06712/13
66218/01
06451/03
8
30/0
073 34/05
067
06464/04
06464/05
06451/04
06093
66305
06465/01
06465-Set
66304
06086
06712/13
06738/05
08523 Set
06087/01
06712/16
06089
06726/40
06716/13
38
32
06723/16
060 06134/01
3
06734/04
7
0
66217
3
1
/
08345
6
71
6
0
07331/07
06730/05
07331/08 66211
4
0
07331/03
/
06716/32
1
3
6 073
31/0
06734/04
3
6
7
4
0
06728/03
682
06036/05
/01
9
06020
1
06037/01
050
07315
68216
06126
06565/29
05724/08
15
682
07315/01
06042/01
06716/13
06045/03
06020
1
038
37/0 06
06534/02 07316
1
6
0
06728/03
06712/16 06039/12
06724/08
07317/11
06738/03
06044/05
06732/05
06739/03
06036/05
07318
08456 06045/01
06745
/11
06039
06049/01
06050
06137/01
06724/18
06734/06
06051
06040/05
06730/05
06727/40
06432 Stadium
06047/01 Monster
06732/07
06445
06088
07091
07384
06093
06732/03
06092
06093
06088
07087/01
66291/05
06732/07
06427 Stadium
06052 Monster
06725/20
06013
06175
07154
66210
06013
04
34/
067 12
662
06176
06716/3
2
06716/22
60239
06730/3
0
36
662
60239/01
06231/07
35
662
04
8/
73
06
06712/16
06033
66258
6
20
68
66207
06033/01
06725/20
06738/04
66208
68213
06067/02
06716/22
06068
68221
06738/05
05
38/ 06722/25
067
03
06029/08
00/
061
37
662
06036/05
06350
6
2/1
71
06
07353
68205
06726/25
06739/05
06724/16
07071/02
06738/05
06069/01
06072/02
08523
66304
06729/30
06073
06732/05
68225
66222
06227/07
06080
06078/05
66223
06077
66226
06079
07352
06734/05
68220
06734/04
07348
06712/16
06734/04
05
63/
06712/16
060
06029/08
30
22/ 0608
067
067
32/0
067 1/01
5
34/0
5
0
0
1
07
75
060
06712/16
01
38/
662
06066/02
067
30/2
5
00
662
06716/09
06064
06081/01
66238/02
07071/01
06720/40
06031
06077/05
06077/08
06078/05
06733/06
06734/06
06029/08
06731/14
06722/35
66230/05
06738/06
06112
7374
Ersatzteilliste/ Spare parts list
7375
7377/8
7300/9 Zenoahmotor G230RC/04
7378/8
7384 Zenoahmotor G260RC
7379/8
Kurbelgehäuse A+B, 1 St.
7385/1
Dichtring, 2 St.
7385/2
Kugellager, 2 St.
7385/3
Kurbelgehäusedichtung, 1 St.
7385/4
Zylinder-Fußdichtung, 1 St.
8344/1
Zylinder G230/04,1St.
8345
Tun.-Zylinder f. FG Zenoah02 ,1St.
Kolben G230/04, 1 St.
7300/9
Kolbenring G230/04, 1 St.
7384
Kolbenbolzen, 1 St.
7301/8
Kolbenbolzensicherung, 2 St.
7303/8
Nadellager kompl., 1 St.
7304/2
Zentrierscheiben f. Nadellager, 2 St.
7305/8
Kurbelwelle kompl., 1 St.
7306/8
Keil für Kurbelwelle, 1 St.
7307/9
Sechskantmutter, 1 St.
7307/10
Mitnehmer f. Kuppl.-Backen, 1 St.
7308/9
Schraube f.Mitnehmer, 1 St.
7309/9
Kupplungsbacken, 2 St.
7310
Kupplungsfeder, 1 St.
7311
Passschrauben f. K.-Backen 2 St.
7312
Lüfterrad/G230/260RC,CY, 1St.
7312/1
Seilzugstartv. kpl./G230/260RC,CY,1St
Startergehäuse/G230/260RC,CY, 1St.
Federkassette /G230/260RC,CY, 1St.
Seilrolle/G230/260RC,CY, 1St.
Starterseil/G230/260RC,CY, 1St.
Startergriff/G230/260RC,CY, 1St.
Starterklinke/G230/260RC,CY, 1St.
Druckfeder/G230/260RC,CY, 1St.
Schraube/ Scheib./ G230/260RC,CY, 3St.
Sicherungsring/G230/260RC,CY, 1St.
Zündkerzenstecker, 1 St.
Zündspule/ G230/260RC,CY, 1St.
Schrauben f.Schalld.M5x60/Zen.,CY 2St.
Schalldämpferdichtung /Zenoah,CY, 2St.
Schraubensatz-Motor, Set
Dichtung f. Isolator /Zenoah,CY, 1St.
Isolator, 1 St.
Dichtung f. Vergaser /Zenoah,CY, 1St.
Vergaserschrauben/ G230/260RC,CY, 2St.
Aus-Schalter/ G230/260RC,CY, 1St.
Motorgehäuse A, 1 St.
Motorgehäuse B, 1 St.
Zündkerze/ G230 RC,CY, 1St.
Kabeldurchführung/ G230/260RC,CY, 1St.
Distanzstück/ G230 RC,CY, 1St.
Vergaser/ G230/260RC,CY, 1St.
Luftfilter/G230/260RC,CY,kompl., 1St.
Luftfilter-Einsatz / Zenoah,CY, 2St.
Vollgasdüsennadel/ Feder, 2 St.
Leerlaufdüsennadel/ Feder G230/04, 2 St.
Membrane-Satz, 2 St.
Vergaserdeckel, 1 St.
Standgasschraube/ Feder, 2 St.
Standgasschr./Feder G230/260RC04, 2St.
Drosselklappenwelle m. Schraube, 2 St.
Drosselklappe, 1 St.
Schenkelfeder, 1 St.
Membrane-Satz, 2 St.
Kunststoffteil m. Vergaser-Nippel, 1 St.
Metallteil f. Pumpe, 1 St.
Schrauben für Metallteil, 4 St.
Pumpe, 1 St.
7301/8
7303/8
7304/2
7305/8
7306/8
7307/9
7307/10
7308/9
7309/9
7310
7311
7312
7312/1
7313/8
7313/1
7314
7315
7315/1
7316
7317/8
7318
7319/8
7323/8
7323/9
7323/10
7323/11
7323/12
7323/13
7323/14
7323/15
7323/16
7326/8
7328/2
7328/8
7330/8
7332
7334/8
7335
7336
7337
7339/8
7340/8
7341/8
7342/8
7343/8
7344/8
7354/8
7355/8
7356/8
7357
7361/8
7362/9
7363
7364
7365
7365/9
7366/8
7367/8
7368
7370
7371
7372
7372/1
7373
Vergaserhebel, 1 St.
7313/8
Schraube f. Vergaserhebel, 1 St.
7313/1
Choke-Welle m. Schraube, 2 St.
7314
Choke-Klappe, 1 St.
7315
Choke-Hebel, 2 St.
7315/1
Zylinder 26 ccm, 1 St.
7316
Kolben 26 ccm, 1 St.
7317/8
Kolbenring 26 ccm, 1 St.
7318
Kolbenbolzen 26 ccm, 1 St.
7319/8
Kuppl.-Flansch Zen. liegend, 1 St. 7323/8
Kuppl.-Flansch Zen. stehend, 1 St. 7323/9
7323/10
Zenoah engine G230RC/04
7323/11
Zenoah engine G260RC
7323/12
7323/13
7323/14
7323/15
7323/16
7326/8
7328/2
7328/8
7330/8
7332
7334/8
7335
7336
7337
7373
7339/8
7340/8
7341/8
7342/8
7343/8
7344/8
7354/8
7355/8
7356/8
7357
7361/8
7362/9
7363
7364
7365
7366/8
7368
7370
7371
7372
7372/1
7373
7374
7375
7377/8
7378/8
7379/8
7305/8
7312/1
7344/8
7341/8
7340/8
7385/1
7385/2
7385/3
7385/4
8344/1
8345
7301/8
Cylinder 26 ccm, 1 pce.
Piston 26 ccm, 1 pce.
Piston ring 26 ccm, 1 pce.
Gudgeon pin 26 ccm, 1 pce.
Coupling flange Solo/Zeno horizontal
Coupling flange Zenoah vertical
EL.7300-9-280906
FG Modellsport GmbH
Spanningerstr. 2
Phone: +49 7181 9677-0
Fax: +49 7181 9677-20
7323/13
7323/11
7323/14
7323/15
7323/16
7323/9
7334/8
7314
7319/8
7323/10
7328/8
7334/8
7323/12
Screws f.carb./G230/260RC,CY, 2pcs.
Circuit breaker/G230/260RC,CY,1pce.
Engine housing A, 1 pce.
Engine housing B, 1 pce.
Spark plug G230 RC,CY, 1pce.
Cable bush./G230/260RC,CY, 1pce.
Spacer block/G230RC,CY, 1 pce.
Carburetor/G230/260RC,CY, 1pce.
Air filter/G230/260RC,CY, 1pce.
Air filter foam, Zenoah,CY 2pcs.
Needle(full-speed)/ spring, 2 pcs.
Needle(idle speed)/spring G230/04,2pcs.
Diaphragm, 2 pcs.
Carburetor cover, 1 pce.
Throttle screw /spring, 2 pcs.
Valve, 1 pce.
Leg spring, 1 pce.
Diaphragm set, 2 pcs.
Plastic part with carb. nipple, 1 pce.
Metal part f. pump, 1 pce.
Screws f. metal part, 4 pcs.
Pump, 1 pce.
Carburetor arm, 1 pce.
Screw f. carburetor arm, 1 pce.
Choke shaft w. screw, 2 pcs.
Choke flap, 1 pce.
Choke lever, 2 pcs.
7343/8
7342/8
7307/9
7307/10
7385/1
7330/8
7332
7334/8
7303/8
7334/8
7311
7310
7385/4
7313/9
7313/8
7312
7308/9
7385/2
ohne Abb.
7328/2
Kerzenstecker
7379/8
7304/2
7306/8
7309/9
7385/3
7335
7374/7375
7378/8
7377/8
7371
7372/1
Crankshaft complete, 1 pce.
Key for crankshaft, 1 pce.
Hexagon nut, 1 pce.
Clutch block carrier, 1 pce.
Screw for carrier, 1 pce.
Clutch blocks, 2 pcs.
Clutch spring, 1 pce.
Dowel screws f. clutch blocks, 2 pcs.
Cooling fan/G230/260RC,CY, 1pce.
Pull start unit/G230/260RC,CY, 1pce.
Starter hous./G230/260RC,CY, 1pce.
Spring assem./G230/260RC,CY, 1pce.
Rope pulley/G230/260RC,CY, 1pce.
Rope/G230/260RC,CY, 1pce.
Starter handle/G230/260RC,CY, 1pce.
Starter ratchet/G230/260RC,CY, 1pce.
Press. spring/G230/260RC,CY, 1pce.
Screw,disks/G230/260RC,CY, 3pcs.
Securing ring/G230/260RC,CY, 1pce.
Spark plug cap, 1pce.
Ignition coil/G230/260RC,CY, 1 pce.
Scews f.silencer M5x60/Zen.,CY,2pcs.
Silencer gasket /Zenoah,CY, 2pcs.
Screw set engine
Insulator gasket/Zenoah,CY, 1pce.
Insulator, 1 pce.
Carburetor gasket/Zenoah,CY, 1pce.
7372
7370
7361/8
7355/8
7336
7301/8
7337
7363
7364
7326/8
7303/8
7368
7365
7365/9
8344/1
8345
7315
7315/1
7366/8 7367/8
7354/8
7362/9
7357
Crank case housing A+B, 1 pce.
Seal ring, 2 pcs.
Bearings, 2 pcs.
Crankshaft gasket, 1 pce.
Cylinder gasket, 1 pce.
Cylinder G230/04, 1 pce.
Tun.-Cylinder f. FG Zen. 02, 1 pce.
Piston G230/04, 1 pce.
Piston ring G230/04, 1 pce.
Gudgeon pin, 1 pce.
Gudgeon pin clips, 2 pcs.
Needle bearing, 1 pce.
Spacer washer, 2 pcs.
7356/8
7339/8
7317/8
7316
7318

Mounting instruction for conversion kit Monster mod

Transcription

Similar documents

Original FG Ersatz- und Tuningteile Original FG Ersatz