For wood construction

For wood construction
Courtesy of Waitomo Glow-worm Caves Visitor Centre
2
3
Content
SPAX product characteristics
4 -5
Zinc yellow passivated
head shape
page
Partial threaded with flat countersunk or washer head
Outer diameter Ø
8 mm
6 -9
Partial threaded with flat countersunk or washer head
Thread outer Ø
10 and 12 mm
10 - 13
8, 10 and 12 mm
14 -17
Fully threaded with flat countersunk head
Thread outer Ø
DELTA®-SEAL
head shape
Technical information
page
18 -19
Partial threaded with washer head
Thread outer Ø
6 mm
20
6 mm
21
8 mm
22
Fully threaded with cylindric head
Thread outer Ø
Fully threaded with cylindric head
Thread outer Ø
Partial threaded with flat countersunk or washer head
Thread outer Ø
Stainless steel
10 mm
A2
Thread outer Ø
24 -25
head shape
A4
8, 10 and 12 mm
Blue zinc plated
page
26 -29
head shape
page
SPAX threaded rod
Fully threaded without head or with hex head
Thread outer Ø
Example applications
Instructions for Ü-Logo
16 mm
30 -33
34 -35
36
Product characteristics
SPAX MULTI Head
flush countersinking.
Mills in wood and stops
on metal.
SPAX MULTI Head
Flat countersunk head
SPAX T-STAR with milled ribs
Flush countersinking.
Countersinks the screw head
flush into the wood.
Flat countersunk head
SPAX T-STAR with milled ribs
Washer head
Better tightening of connections
also of warped boards.
Higher pull through forces.
Allows savings with regard to
reduced screw numbers and
working time.
Washer head
Cylindric head
Low splitting effect when sinking
the head.
Can be easily countersunk in wood.
Cylindric head
4
5
SPAX T-STAR plus
positive and secure fit of the
bit and better driving, e. g.
when working overhead.
SPAX T-STAR plus
SPAX 4CUT cutter
from screw lengths over 160 mm.
Reduces the screwing in torque
significantly.
SPAX 4CUT cutter
SPAX 4CUT point
no pre-drilling (wood-dependent),
reduces splitting. Square end
displaces the fibres and reduces
the screwing in torque.
SPAX ground serrations
For quick and secure fastening.
SPAX 4CUT point and SPAX ground serrations
SPAX CUT point
no pre-drilling (wood-dependent),
reduces splitting.
SPAX typical ground serrations
For quick and secure fastening.
SPAX CUT point
and SPAX typical ground serrations
Courtesy of Waitomo
Glow-worm Caves Visitor Centre
6
7
Partial threaded
with flat countersunk and washer head
Outer diameter 8 mm
Features:
Significantly reduced screwing torque and
reduced splitting effect
Easier and faster screwing
No pre-drilling necessary (wood-dependent)
Approved by German building authorities under
licensing number Z-9.1-449. Z-9.1-511 –
approved by building authorities for fastening
rooftop insulation systems
Recess SPAX T-STAR plus T40
Length specification and manufacturer
ID on the head.
Washer head ensures higher
pull through forces
gth
80
The
m
0m
len
tal
to
5
–4
penetrates the wood significantly more easily and faster!
Time [s]
24.3
23.1
21.9
20.7
19.5
17
18.2
15.8
14.6
13.4
12.2
10.9
9.73
7.3
8.51
6.08
4.86
3.65
2.43
Conventional
screw
1.22
into fir wood
gluelam
Screwing torque [Nm]
8 x 600 mm
Ls
Ø d1
LgT
90°
Ø dk
Flat countersunk head,
SPAX T-STAR plus
with SPAX MULTI Head
and SPAX 4CUT point,
case hardened, slide-coated
Zinc yellow passivated A2L
Packaging
units
Dimensions [mm]
SPAX T-STAR plus
SPAX MULTI Head
Thread Ø
d1
Length
total
Ls
8.0
80
47
40
100
57
40
120
70
40
140
80
40
With 4CUT cutter
160
80
40
180
80
40
200
80
40
220
80
40
240
80
40
260
80
40
280
80
40
300
80
40
320
80
40
340
80
40
360
80
40
380
80
40
400
80
40
450
80
40
dk (Ø) =
15.1 mm
Length
partial
thread
LgT
Bit size
T-STAR
plus
T
SPAX No.
SPAX
BOX
[pieces]
50
50
50
50
0191020800805
0191020801005
0191020801205
0191020801405
50
50
50
50
50
50
50
50
50
50
50
50
50
50
0191020801605
0191020801805
0191020802005
0191020802205
0191020802405
0191020802605
0191020802805
0191020803005
0191020803205
0191020803405
0191020803605
0191020803805
0191020804005
0191020804505
Other lengths, head shapes and surfaces on request.
On request available in DELTA®-SEAL coating for treated Timber see page 18/19.
SPAX 4CUT cutter
Practical screwing aid for rooftop insulation
For use with SPAX 8 mm allowing precise and pinpoint fastening
in the rafter (67° angle).
T 40
8
9
0191020802405
4CUT
SPAX 4CUT point
and SPAX ground serrations
5001020800011
1 unit per box
A2L
SPAX No.
Packaging unit
50
8 240
X
'!0A35DA-aebieg!
Z-9.1-449
Washer head,
SPAX T-STAR plus
with SPAX 4CUT point,
case hardened,
slide-coated
Ls
Ø dk
Ø d1
Lg
Zinc yellow passivated A2L
Packaging
units
Dimensions [mm]
Thread Ø
d1
Length
total
Ls
8.0
80
70 ■ 40
100
80 ■ 40
120
80 ■ 40
140
80 ❑ 40
With 4CUT cutter
160
80 ❑ 40
180
80 ❑ 40
200
80 ❑ 40
220
80 ❑ 40
240
80 ❑ 40
260
80 ❑ 40
280
80 ❑ 40
300
80 ❑ 40
320
80 ❑ 40
340
80 ❑ 40
360
80 ❑ 40
380
80 ❑ 40
400
80 ❑ 40
450
80 ❑ 40
dk (Ø) =
20 mm
Length
thread
Lg
Bit size
T-STAR
plus
T
SPAX No.
SPAX
BOX
[pieces]
50
50
50
50
0251020800805
0251020801005
0251020801205
0251020801405
50
50
50
50
50
50
50
50
50
50
50
50
50
25
0251020801605
0251020801805
0251020802005
0251020802205
0251020802405
0251020802605
0251020802805
0251020803005
0251020803205
0251020803405
0251020803605
0251020803805
0251020804005
0251020804505
SPAX T-STAR plus
Washer head
Other lengths, head shapes and surfaces on request.
On request available in DELTA®-SEAL coating for treated Timber see page 18/19.
■ T-STAR plus, full thread
❑ T-STAR plus, partial thread
SPAX 4CUT cutter
T 40
0251020802405
4CUT
A2L
SPAX 4CUT point and SPAX ground serrations
50
8 240
X
'!0A35DA-ajheeh!
Z-9.1-449
Courtesy of Waitomo
Glow-worm Caves Visitor Centre
10
11
Partial threaded
with flat countersunk and washer head
Outer diameter 10 and 12 mm
Features:
No pre-drilling necessary (wood-dependent)
Absorption of high tensile and compressive
forces by being fully threaded
Approved by German building authorities under
licensing number Z-9.1-449. Z-9.1-511 –
approved by building authorities for fastening
rooftop insulation systems
Recess SPAX T-STAR
Length specification and manufacturer
ID on the head
80
m
0m
gth
en
al l
tot
0
–6
gth
–
80
45
m
0m
to
len
tal
Ls
Ø d1
LgT
90°
Ø dk
Flat countersunk head,
SPAX T-STAR
with milled ribs,
case hardened,
slide-coated
Zinc yellow passivated A2L
Packaging
units
Dimensions [mm]
Thread Ø
d1
Length
total
Ls
Length
partial
thread
LgT
Bit size
T-STAR
plus
T
SPAX
BOX
[pieces]
10.0
80
100
120
140
160
180
200
220
240
260
280
300
320
340
360
380
400
450
100
120
140
160
180
200
220
240
260
280
300
350
400
450
500
550
600
50
60
70
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
60
80
80
100
100
100
100
100
100
100
100
100
100
100
100
100
100
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
20
20
dk (Ø) =
18.6 mm
Flat countersunk head
SPAX T-STAR with milled ribs
12.0
dk (Ø) =
22.6 mm
SPAX typical ground serrations
SPAX No.
0191021000805
0191021001005
0191021001205
0191021001405
0191021001605
0191021001805
0191021002005
0191021002205
0191021002405
0191021002605
0191021002805
0191021003005
0191021003205
0191021003405
0191021003605
0191021003805
0191021004005
0191021004505
0191021201005
0191021201205
0191021201405
0191021201605
0191021201805
0191021202005
0191021202205
0191021202405
0191021202605
0191021202805
0191021203005
0191021203505
0191021204005
0191021204505
0191021205005
0191021205505
0191021206005
Other lengths, head shapes and surfaces on request.
On request available in DELTA®-SEAL coating for treated Timber see page 18/19.
12
13
'!0A35DA-ajafbg!
Z-9.1-449
50 Stück
10X240
Art.: 0191021002405
A2L
Senkkopf mit Fräsrippen T 50
verzinkt, gelb pass.
Washer head,
SPAX T-STAR
Case hardened,
slide-coated
Ls
Ø dk
Ø d1
Lg
Zinc yellow passivated A2L
Packaging
units
Dimensions [mm]
Thread Ø
d1
Length
total
Ls
Length
thread
Lg
Bit size
T-STAR
plus
T
SPAX
BOX
[pieces]
10.0
80
100
120
140
160
180
200
220
240
260
280
300
320
340
360
380
400
450
70 ▲
80 ▲
80 ▲
80
80
80
80
80
80
80
80
80
80
80
80
80
80
80
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
25
25
25
25
25
25
25
25
25
25
25
25
25
25
dk (Ø) =
25 mm
SPAX No.
0251021000805
0251021001005
0251021001205
0251021001405
0251021001605
0251021001805
0251021002005
0251021002205
0251021002405
0251021002605
0251021002805
0251021003005
0251021003205
0251021003405
0251021003605
0251021003805
0251021004005
0251021004505
Washer head
Other lengths, head shapes and surfaces on request.
On request available in DELTA®-SEAL coating for treated Timber see page 18/19.
▲ T-STAR, full thread
T-STAR, partial thread
A2L
SPAX typical ground serrations
Z-9.1-449
14
15
Fully threaded with flat countersunk
Outer diameter 8, 10 and 12 mm
Features:
Absorption of high tensile and compressive
forces by being fully threaded
Absorption of particularly high pulling
forces compared to partial threaded
screws
Wide spectrum of applications through screw
lengths of up to 600 mm
Approved by German building authorities
under Z-9.1-519
Length specification and manufacturer
ID on the head
160
–6
0
m
0m
gth
tot
en
al l
Ls
Ø d1
LgV
90°
Ø dk
Flat countersunk head,
SPAX T-STAR plus
with SPAX MULTI Head and
SPAX CUT point,
case hardened, slide-coated
Zinc yellow passivated A2L
Packaging
units
Dimensions [mm]
SPAX MULTI Head
Length
total
Ls
8.0
160
180
200
220
240
260
280
300
350
400
450
500
550
600
dk (Ø) =
15.1 mm
Length
full
thread
LgV
Thread close to head
SPAX T-STAR plus
Thread Ø
d1
Bit size
T-STAR
plus
T
SPAX
BOX
[pieces]
40
40
40
40
40
40
40
40
40
40
40
40
40
40
50
50
50
50
50
50
50
50
50
50
50
25
25
25
SPAX No.
1201020801605
1201020801805
1201020802005
1201020802205
1201020802405
1201020802605
1201020802805
1201020803005
1201020803505
1201020804005
1201020804505
1201020805005
1201020805505
1201020806005
Other lengths, head shapes and surfaces on request.
On request available in DELTA®-SEAL coating for treated Timber see page 18/19.
T 40
16
17
1201020802405
A2L
SPAX CUT point
and SPAX typical ground serrations
50
8 240
X
'!0A35DA-bddegg!
CUT
Z-9.1-519
Ls
Ø d1
LgV
90°
Ø dk
Flat countersunk head,
SPAX T-STAR
with milled ribs and
SPAX CUT point,
case hardened, slide-coated
Zinc yellow passivated A2L
Packaging
units
Dimensions [mm]
10.0
200
220
240
260
280
300
350
400
450
500
550
600
200
220
240
260
280
300
350
400
450
500
500
600
dk (Ø) =
18.6 mm
12.0
dk (Ø) =
18.6 mm
Length
full
thread
LgV
Thread close to head
Length
total
Ls
Thread close to head
Thread Ø
d1
Bit size
T-STAR
plus
T
SPAX
BOX
[pieces]
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
25
25
25
25
25
25
25
25
25
25
25
25
25
20
20
SPAX No.
1201021002005
1201021002205
1201021002405
1201021002605
1201021002805
1201021003005
1201021003505
1201021004005
1201021004505
1201021005005
1201021005505
1201021006005
1201021202005
1201021202205
1201021202405
1201021202605
1201021202805
1201021203005
1201021203505
1201021204005
1201021204505
1201021205005
1201021205505
1201021206005
Other lengths, head shapes and surfaces on request.
A2L
On request available in DELTA®-SEAL coating for treated Timber see page 18/19.
CUT
Z-9.1-519
Flat countersunk head
SPAX T-STAR with milled ribs
SPAX CUT point
and SPAX typical ground serrations
S
A
T
L
DE
®
18
19
L
A
E
S
DELTA®-SEAL
The DELTA®-SEAL is a system topcoat.
The topcoat provides controlled properties, which makes these the ideal seal over
electroplated layers.
Product description:
DELTA®-SEAL is a zinc flake coating system. The system comprises electroplated
base layer and DELTA®-SEAL topcoat which provides highly effective anti-corrosion
protection and other properties regulated by sealer.
DELTA®-SEAL is free of any harmful heavy metals, such as Cr-(VI), and conforms
to EU guidelines.
No hydrogen embrittlement occurs in the application of DELTA®-SEAL.
As appropriate, the coating process can be carried out jigged or in bulk.
Properties:
Including lubricant coating for reduced torque while driving the screw home
Special features:
Organic topcoat
Withstands ACQ, CCA, and LOSP timber treatments.
Excellent chemical resistance
Particularly suitable for multiple screw fixing
DELTA®-SEAL in comparison:
DELTA®-SEAL compared with zinc yellow electro plated
10 times higher corrosion resistance.
DELTA®-SEAL compared with standard galvanized screws
more than twice the corrosion resistance.
Tests carried out with neutral salt spray test.
Corrosion resistance endurance life – DIN EN ISO 9227 (depending upon the
build-up of coats, geometry and type of application)
Ls
Ø d1
Lg
Ø dk
Washer head,
SPAX T-STAR plus
with SPAX 4CUT point,
case hardened, slide-coated
DELTA®-SEAL
Packaging
units
Dimensions [mm]
SPAX T-STAR plus
Thread Ø
d1
Length
total
Ls
6.0
60
56 ■ 30
80
61 ■ 30
100
61 ❑ 30
120
68 ❑ 30
140
68 ❑ 30
With 4CUT cutter
160
65 ❑ 30
180
65 ❑ 30
dk (Ø) =
13.6 mm
Length
thread
Lg
Bit size
T-STAR
plus
T
SPAX No.
SPAX
BOX
[pieces]
200
200
100
100
100
0251900600605
0251900600805
0251900601005
0251900601205
0251900601405
100
100
0251900601605
0251900601805
Other lengths, head shapes and surfaces on request.
4CUT
SPAX 4CUT point
and SPAX ground serrations
S
A
T
L
DE
®
T 30
20
21
0251900601805
SPAX 4CUT cutter
■ T-STAR plus, full thread
❑ T-STAR plus, partial thread
A9L
Washer head
100
6 180
X
'!0A35DA-biddhj!
Z-9.1-235
Cylindric head,
SPAX T-STAR plus
with SPAX 4CUT point,
case hardened, slide-coated
Ls
Ø dk
Ø d1
LgV
DELTA®-SEAL
Packaging
units
Thread Ø
d1
Length
total
Ls
6.0
80
100
120
140
160
180
200
dk (Ø) =
8.4 mm
Length
full
thread
LgV
Bit size
T-STAR
plus
T
SPAX
BOX
[pieces]
Thread close to head
Dimensions [mm]
30
30
30
30
30
30
30
200
100
100
100
100
100
100
SPAX No.
1211900600805
1211900601005
1211900601205
1211900601405
1211900601605
1211900601805
1211900602005
SPAX T-STAR plus
Other lengths, head shapes and surfaces on request.
Please check availability with your local distributor.
Cylindric head
L
A
SE
T 30
1211900601805
4CUT
A9L
SPAX 4CUT point and SPAX ground serrations
100
6 180
X
'!0A35DA-bidefe!
Z-9.1-519
NEW
SPAX T-STAR plus
Ø d1
LgV
DELTA®-SEAL
Packaging
units
Dimensions [mm]
Thread Ø
d1
Length
total
Ls
8.0
200
220
240
260
280
300
350
400
450
dk (Ø) =
10 mm
Length
full
thread
LgV
Thread close to head
NEW
Ls
Ø dk
Cylindric head,
SPAX T-STAR plus
with SPAX CUT point,
case hardened, slide-coated
Bit size
T-STAR
plus
T
SPAX
BOX
[pieces]
40
40
40
40
40
40
40
40
40
50
50
50
50
50
50
50
50
50
SPAX No.
1221900802005
1221900802205
1221900802405
1221900802605
1221900802805
1221900803005
1221900803505
1221900804005
1221900804505
Other lengths, head shapes and surfaces on request.
Please check availability with your local distributor.
Cylindric head
DE
L
A
E
S
A
LT
®
T 40
22
23
1121900802405
A9L
SPAX CUT point
and SPAX typical ground serrations
50
8 240
X
'!0A35DA-bidegb!
CUT
Z-9.1-519
SPAX fully threaded screws,
application area
Reinforcing notched beams e.g. at beams
support
SPAX 8 x 400
with full thread
Due to timbers characteristic minimal load
bearing capacity for tension lateral to grain,
reinforcing of notched beams can increase their
load bearing capacity significantly.
Binder GL 24h,
20 x 60 cm2
53.2 kN
Connecting lowered beams to main beam
≥ 0.7 ∙ H
SPAX full thread screws are especially applicable
to transfer high tension loads. Instead of headpull-through the load bearing capacities of the
two thread parts are taken into account.
Supporting beam A
Reinforcing beams support area
Vd = 248 kN
Due to timbers characteristic minimal load
bearing capacity for compression lateral to grain,
reinforcing the support area can increase their
load bearing capacity significantly.
Binder GL 28h, 20 x 145 cm2
SPAX 10 x 450 with full thread
Steel sheet t = 8 mm
Neoprene bearing
Reinforced concrete support 45 x 45 cm
300 mm
Ls
Ø d1
LgT
90°
Ø dk
Flat countersunk head,
SPAX T-STAR
with milled ribs,
case hardened,
slide-coated
DELTA®-SEAL
Packaging
units
Dimensions [mm]
Thread Ø
d1
Length
total
Ls
Length
partial
thread
LgT
Bit size
T-STAR
plus
T
SPAX
BOX
[pieces]
10.0
80
100
120
140
160
180
200
220
240
260
280
300
47
57
70
80
80
80
80
80
80
80
80
80
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
25
25
25
25
25
25
25
25
dk (Ø) =
18.6 mm
Flat countersunk head
SPAX T-STAR with milled ribs
SPAX typical ground serrations
SPAX No.
0191901000805
0191901001005
0191901001205
0191901001405
0191901001605
0191901001805
0191901002005
0191901002205
0191901002405
0191901002605
0191901002805
0191901003005
Other lengths, head shapes and surfaces on request.
S
A
T
L
DE
®
Senkkopf mit Fräsrippen T 50
24
25
'!0A35DA-bideeh!
Z-9.1-449
50 Stück
10X240
Art.: 0191901002405
gelb verzinkt 10my+deltaseal silber
Washer head,
SPAX T-STAR
Case hardened,
slide-coated
Ls
Ø dk
Ø d1
Lg
DELTA®-SEAL
Packaging
units
Dimensions [mm]
Thread Ø
d1
Length
total
Ls
Length
thread
Lg
Bit size
T-STAR
plus
T
SPAX
BOX
[pieces]
10.0
80
100
120
140
160
180
200
220
240
260
280
300
70 ▲
80 ▲
80 ▲
80
80
80
80
80
80
80
80
80
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
25
25
25
25
25
25
25
25
dk (Ø) =
25 mm
SPAX No.
0251901000805
0251901001005
0251901001205
0251901001405
0251901001605
0251901001805
0251901002005
0251901002205
0251901002405
0251901002605
0251901002805
0251901003005
Other lengths, head shapes and surfaces on request.
Washer head
▲ T-STAR, full thread
T-STAR, partial thread
L
A
SE
SPAX typical ground serrations
'!0A35DA-bhheai!
Z-9.1-449
Art.: 0251901002405
gelb verzinkt 10my+deltaseal silber
26
27
Outer diameter
8, 10 and 12 mm
Fields of application:
For use outside (e.g. carports, playground
equipment, pergolas, porches, bridges,
bridge plank flooring, balconies)
Fastening of sheet metal
(e.g. solar roof hooks)
Securing of carpenter wood connections
(e.g. offsets)
50
m
0m
gth
en
al l
tot
0
–2
160
–5
5
m
0m
gth
tot
en
al l
NEW
Washer head,
SPAX T-STAR plus
with SPAX 4CUT point,
slide-coated
ange
uct r ed!
d
o
r
P pand
ex
SPAX T-STAR plus
Ls
Ø dk
Ø d1
Lg
Stainless steel A2 II
Packaging
units
Dimensions [mm]
Thread Ø
d1
Length
total
Ls
8.0
50
46 ■ 40
60
56 ■ 40
80
70 ■ 40
100
80 ■ 40
120
80 ■ 40
140
80 ❑ 40
With 4CUT cutter
160
80 ❑ 40
180
80 ❑ 40
200
80 ❑ 40
dk (Ø) =
20 mm
Length
thread
Lg
Bit size
T-STAR
plus
T
SPAX No.
SPAX
BOX
[pieces]
50
50
50
50
50
50
0257000800505
0257000800605
0257000800805
0257000801005
0257000801205
0257000801405
50
50
50
0257000801605
0257000801805
0257000802005
For new articles, price and quantity are available upon request.
Other lengths, head shapes and surfaces on request.
Washer head
■ T-STAR plus, full thread
❑ T-STAR plus, partial thread
SPAX 4CUT cutter
T40
28
29
0257000801605
304
4CUT
SPAX 4CUT point
and SPAX ground serrations
INOX
STAINLESS STEEL
50
8 160
X
'!0A35DA-bhhjba!
Z-9.1-449
NEW!
NEW!
NEW!
NEW!
NEW
Ls
Ø d1
LgV
90°
Ø dk
Flat countersunk head,
SPAX T-STAR
with cutting rips,
SPAX CUT point,
slide-coated
NEW
Stainless steel A4 III
Packaging
units
Dimensions [mm]
Length
total
Ls
10.0
160
200
220
240
260
280
300
350
400
400
450
500
550
12.0
dk (Ø) =
18.6 mm
Thread close
to head
dk (Ø) =
18.6 mm
Length
full
thread
LgV
Thread close to head
Thread Ø
d1
Bit size
T-STAR
plus
T
SPAX
BOX
[pieces]
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
50
25
25
25
25
SPAX No.
1208001001605
1208001002005
1208001002205
1208001002405
1208001002605
1208001002805
1208001003005
1208001003505
1208001004005
1208001204005
1208001204505
1208001205005
1208001205505
For the entire product range, price and quantity are available upon request.
Other lengths, head shapes and surfaces on request.
Flat countersunk head
SPAX T-STAR with milled ribs
SPAX CUT point
and SPAX typical ground serrations
Senkkopf mit Fräsrippen T 50
CUT
'!0A35DA-bhigij!
Z-9.1-519
50 Stück
10X240
Art.: 1208001002405
A4
INOX
STAINLESS STEEL
316
Ice sport hall Erfurt
www.gunda-niemann-stirnemann-halle.de
30
31
SPAX threaded rod
The alternative for transverse reinforcement
The features at a glance:
Transverse reinforcement in cases of large wooden
constructions (usually made of gluelam)
Ideal replacement for glued threaded rods
Ideal also for use in subsequent refurbishment at
building site, irrespective of the outside temperature
Dimensioning according to national technical
approval number Z-9.1-832
Possible to work overhead
No glue necessary: saving time and money
Less sensitive to adverse conditions
(damp, temperature, …)
Pre-drilling to core diameter with 12 -13 mm
Low screwing-in torque
Galvanised and additional sliding coating
–
800
m
0m
tot
220
gth
m
0m
gth
en
al l
len
tal
to
300
Z-9.1-832
SPAX threaded rod
without head,
slide-coated
Ø d1
Ls
Blue zinc plated A2J
Dimensions [mm]
Packaging
units
Thread Ø
d1
Length
total
Ls
Shaft ring
[piece]
16.0
3,000
10
SPAX No.
35616000201011
Other lengths on request.
SPAX-screw-sleeve, width across flats SW 11
For threaded rods without head
SPAX No.
Sales unit
5001900900011
1 piece in carton
For pre-drilling, the following drills
having a diameter of 12 to 13 mm are
recommendable:
FAMAG, Remscheid:
Auger bit
32
33
WOODTEC FANKHAUSER, CH-Vordemwald:
Deep hole drill flushed with pressurised air
Ls
SPAX threaded rod
with hex head,
slide-coated
Ø dk
Ø d1
LgV
Blue zinc plated A2J
Packaging
units
Dimensions [mm]
Length
total
Ls
16.0
800
1,000
1,200
1,400
1,600
1,800
2,000
2,200
dk (Ø) =
26 mm
Length
full
thread
LgV
Thread close to head
Thread Ø
d1
Widths
across
flats
SW 22
SW 22
SW 22
SW 22
SW 22
SW 22
SW 22
SW 22
SPAX No.
Shaft
ring
[piece]
25
25
25
25
25
25
25
25
35616000108011
35616000101011
35616000102011
35616000103011
35616000104011
35616000105011
35616000106011
35616000107011
Other lengths on request.
SPAX threaded rods are
wood screws according to
DIN 1052 : 2008-12 with
continuous thread to DIN 7998.
Pre-drilling
Hexagonal head SW 22 mm
Outer Ø d1
= 16 mm
Core -Ø d3
= 12 mm
What must be observed
during processing:
The drill bit can deviate in case
of very narrow components
and long drilled holes. If no
experience is available in
the factory, please check in
advance.
Screwing in
The following machines are
recommended for screwing-in:
PROTOOL DRP 32-4,
BOSCH GBM 32-4,
FEIN angle screwing machine
Mammut SCW 16-6,
MAKITA angle screwing
machine DA 4301.
Shortening to desired length
possible.
Ready!
Use drill bits with Ø 12-13 mm.
Z-9.1-832
Example applications
Wall connection, wood frame
construction
Economic alternative to coach
screw conf. to DIN 571
Safe tightening, e.g. of wall
fixtures
No pre-drilling necessary
(wood-dependent)
67% higher hold down forces
than other screws
Rafter connection, purlin
Fastening the rafters. With the
washer head screw even heavily
twisted rafters can be tightened
High wind draft protection
Does without rafter purlin
anchors
Z-9.1- 511 – approved by building
authorities for fastening rooftop
insulation systems
Washer head ensures higher
head to hold down forces,
allowing for larger screw
distances
Static calculation service
34
35
Partial threaded
Fully threaded
Lateral pressure reinforcement
Simple and universal opportunity
for increasing the bearing pressure
through fully threaded screws
Apply computing procedure
according to Z-9.1-519
Lateral tension reinforcements
conforming to DIN 1052:2008-12
Safe alternative to glued on
reinforcing boards and glued in
threaded bars
Can be performed by any carpentry
business
No gluing license necessary
Can be safely applied on site even
after construction
(e.g. when renovating)
Flexibly connected bending beams
High stiffness of the overall
cross section through angularly
aligned screws (cross-sectional
strengthening)
Particularly of interest in the field of
renovation
Cost-effective alternative to:
Bolt connections
Formed sheet metal parts
Laterally reinforced through:
– glued on reinforcement panels
or
– glued in threaded bars
Ü-Logo
Approval Notification
Certificate of Compliance
Ü-Logo
By SPAX according to
General Technical Approvals
For SPAX different General Technical
Approvals are available regulating their
use as building and construction product.
Please be aware that not only an
approval is needed but also a
certificate of compliance of a
therefore accredited inspection agency!
This certificate attests that the products
correspond to the approval and that
a proper self monitoring and external quality
control are existant. Therefore, we as the
producer, are qualified to supply our products
with the Ü-Logo.
Of course, SPAX has all these
documents on hand. From our certificate of
compliance, which is accessible
at any time (i.e. as a download on
www.spax.com or on demand), you can see
that SPAX is produced in Germany.
Quality “Made in Germany”!
SPAX International GmbH & Co. KG
OFFICIAL DISTRIBUTOR:
www.spaxpacific.com
Australia
New Zealand
Phone +61- (0) 4 19 - 02 87 64
Phone +64- (0) 8 00 - 77 29 69
4735 / 04 / 12 / AUS / ???
KÖLNER STRASSE 71-77 · D-58256 ENNEPETAL · GERMANY
TEL + 49-(0) 23 33-799-0 · FAX + 49-(0) 23 33-799-199
info@spax.com · www.spax.com
www.sanderwerbung.de
ALTENLOH, BRINCK & CO - GRUPPE