Saab 9-3 4D/5D M03

Monteringsanvisning
900
SCdefault
MONTERINGSANVISNING · INSTALLATION INSTRUCTIONS
MONTAGEANLEITUNG · INSTRUCTIONS DE MONTAGE
SITdefault
Saab 9-3 4D/5D M03-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
Saab 9-5 M01- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 17
Handsfree kit, mobile phone
Accessories Part No.
Group
Date
Instruction Part No.
32 025 907
9:89-31
Nov 06
32 025 872
Replaces
F930A592
2 32 025 872
1x
1x
1x
11x
1x
1x
1x
F930A488
32 025 872 3
Saab 9-3 4D/5D M03-
1
2
B
A
C
B
F930A489
3
F930A490
4
F930A491
1 Ignition in OFF position.
2 Remove the floor console's right-hand side
piece.
3 Remove the lower glove box screws.
4 Remove the inner glove box screws.
Saab 9-3 4D/5D M03-
F930A492
4 32 025 872
5
6
A
B
F930A493
7
F930A494
8
F930A495
5 Unplug the connector for the glove box lighting
(A).
Cars with ACC: Remove the coolant hose from
the glove box (B).
6 Remove the cover plate from the A-pillar trim.
7 Remove the retaining screw.
8 Grip the upper edge of the A-pillar trim and carefully pull out and up.
Saab 9-3 4D/5D M03-
F930A496
32 025 872 5
9
10
F930A497
11
F930A498
12
F930A499
9 Remove the rear cover.
10 Remove the front cover.
11 Remove the screws.
12 Remove the centre cover.
Saab 9-3 4D/5D M03-
F930A500
6 32 025 872
14
13
F930A502
F930A501
15
16
F930A503
13 Cars with rain sensor: Remove the cover.
14 Fit the adhesive tape onto the microphone.
15 Fit the microphone.
16 Insert the microphone cable through the hole in
the headlining by the roof console.
Saab 9-3 4D/5D M03-
F930A504
32 025 872 7
17
18
F930A506
F930A505
19
20
F930A507
17 Route the microphone cable on under the headlining towards the windscreen. Press in the centre cover and draw the microphone cable tight at
the same time.
18 Route the microphone cable under the headlining.
19 Secure the microphone cable to the A-pillar.
20 Route the microphone cable under the panel,
and on to the centre console and secure it.
Important
Fasten the wiring harness correctly so that there is
no risk of it chafing or rattling.
Saab 9-3 4D/5D M03-
F930A508
8 32 025 872
22.1-22.5
21.1-21.7
F930A509
Fit the keypad in accordance with one of the alternatives.
Saab 9-3 4D/5D M03-
32 025 872 9
21.2
21.1
A
A
B
F930A511
21.3
B
F930A512
21.4
F930A513
21 Fitting the keypad, alternative 1:
21.1 Remove the ashtray/storage compartment.
21.2 Remove the ACC panel.
21.3 Fit the keypad to the console and mark out
the cable route.
21.4 Cut out from the console for the cable.
Saab 9-3 4D/5D M03-
F930A514
10 32 025 872
21.5
21.6
F930A515
21.7
A
B
F930A516
21.5 Fit the keypad to the console.
21.6 Route the cable down behind the radio
down towards the air bellows and secure it.
Important
Fasten the wiring harness correctly so that there is
no risk of it chafing or rattling.
21.7 Fit the ACC panel (A). Check that the keypad's cable is located in the groove. Fit the
ashtray/storage compartment (B).
Saab 9-3 4D/5D M03-
F930A517
32 025 872 11
22.1
22.2
B
A
F930A518
22.3
F930A519
22.4
B
A
F930A520
22 Fitting the keypad, alternative 2:
22.1 Remove the cover.
22.2 Route the cable along the right-hand side,
down towards the air bellows.
22.3 Route the cable in the dashboard's groove.
22.4 Fit the cover.
Saab 9-3 4D/5D M03-
F930A521
12 32 025 872
22.5
23
A
F930A522
B C
F930A523
25
24
F930A524
22.5 Fit the keypad and adjust any excess cable
length.
23 Connect the control module (A), microphone (B)
and keypad (C) to the adapter harness.
24 Secure the control module using two cable ties
to the panel member.
25 Release the Tele1 connection from the car's
cable harness by cutting the tape. The Tele1
connection is located adjacent to the lower edge
of the centre console on the right-hand side.
Saab 9-3 4D/5D M03-
F930A525
32 025 872 13
27
26
F930A527
F930A528
29
28
F930A529
26 Connect the adapter harness to the car's Tel 1
connection and secure the wiring.
27 Secure the wiring to the panel member.
Important
Fasten the wiring harness correctly so that there is
no risk of it chafing or rattling.
28 Cars with rain sensor: Fit the cover.
29 Fit the screws to the cover.
Saab 9-3 4D/5D M03-
F930A530
14 32 025 872
30
31
F930A531
32
F930A532
33
5Nm
(4lbf ft)
F930A533
30 Fit the front cover.
31 Fit the rear cover.
32 Align the A-pillar trim in position. Take care not
to damage the inflatable curtain.
WARNING
Take care not to damage the inflatable curtain.
Damage could result in the inflatable curtain not
providing the intended protection to the occupants
in the event of a collision.
33 Fit the retaining screw.
Tightening torque: 5 Nm (4 lbf ft).
Saab 9-3 4D/5D M03-
F930A534
32 025 872 15
35
34
A
B
F930A535
F930A536
37
36
F930A537
34 Fit the cover plate to the A-pillar trim.
35 Plug in the connector for the glove box lighting
(A).
Cars with ACC: Fit the coolant hose for the
glove box (B).
36 Fit the inner glove box screws.
37 Fit the lower glove box screws.
Saab 9-3 4D/5D M03-
F930A538
16 32 025 872
38
B
C
A
F930A539
38 Fit the floor console's right-hand side piece.
Saab 9-3 4D/5D M03-
32 025 872 17
Saab 9-5 M01-
M01-05
2.1
1
A
CLICK
B
E930A427
M01-05
2.2
E930A428
M01-05
2.3
E930A429
1 Ignition in OFF position.
2 Remove the radio/navigation unit, M01-05:
2.1 Insert the special tools into the intended
holes until the tools engage and pull out
the unit.
2.2 Remove the compartment.
2.3 Unplug the connectors.
Saab 9-5 M01-
E930A430
18 32 025 872
M063.1
M063.2
E930A431
4
A
B
E930A433
3 Remove the radio/navigation unit, M063.1 Remove the plugs and remove the screws.
3.2 Pull the unit out and unplug the connectors
and disconnect the antenna connection.
4 Remove the ACC panel.
Saab 9-5 M01-
E930A432
32 025 872 19
5
B
B
B
A
C
D
E930A434
5 Remove the lower section of the dashboard on
the driver's side:
5.1 Remove the data link connector (A).
5.2 Remove the lower panel (B).
5.3 Remove the clip (C).
5.4 Remove the floor lighting (D).
Saab 9-5 M01-
20 32 025 872
6
7
A
E930A435
8
E930A436
9
A
B
E930A437
6 Remove the cover to the fuses.
7 Remove the A-pillar trim (secured with clips).
Remove the upper clip (A) from the trim.
WARNING
Take care not to damage or loosen the energy
absorbers. Damaged or loosened energy absorbers must not be refitted. In appropriate cases, the
whole of the headlining must be replaced. A damaged energy absorber could provide reduced protection to the head in the event of impact.
8 Remove the sun visor's screws and allow the
sun visor to hang down.
9 Remove the glass cover (A), the retaining screw
(B) and lower the cover.
Saab 9-5 M01-
E930A438
32 025 872 21
10
11
E930A439
E930A440
13
12
E930A441
10 Fit the adhesive tape to the microphone.
11 Press the microphone in on the outside of the
cover, beside the car's original microphone.
12 Route the microphone cable up, under the
headlining and on, down around the A-pillar.
13 Secure the microphone cable up against the
existing cable ties.
Saab 9-5 M01-
E930A442
22 32 025 872
14
B
A
E930A443
14 Press the cover in, fit the retaining screw (B) and
the glass cover (A).
Saab 9-5 M01-
32 025 872 23
E930A444
15 Route and secure the microphone cable:
Route the cable under the panel, towards the
centre console and in behind the radio/navigation unit.
Secure the cable under the panel (A).
Important
Fasten the wiring harness correctly so that there is
no risk of it chafing or rattling.
Saab 9-5 M01-
24 32 025 872
16
17
E930A446
18.1
E930A447
18.2
E930A448
16 Remove the cover for the heating and ventilation unit.
17 Fold aside the floor carpet.
18 Cars with diesel engine:
18.1 Remove the sound absorber.
18.2 Cut out the top insulation layer.
Saab 9-5 M01-
E930A445
32 025 872 25
19
20
E930A449
E930A450
22
21
E930A451
19 Position the adapter harness.
20 Connect the control module to the adapter harness.
21 Align the control module and secure the wiring.
Important
Fasten the wiring harness correctly so that there is
no risk of it chafing or rattling.
22 Cars with diesel engine: Fit the sound absorber.
Saab 9-5 M01-
E930A452
26 32 025 872
23
24
E930A453
25
E930A454
26
E930A455
23 Refit the floor carpet.
24 Fit the cover for the heating and ventilation unit.
25 Cut the tape around the Tele1 connection on the
car's wiring harness.
26 Connect the adapter harness to the car's Tele1
connection.
Saab 9-5 M01-
E930A456
32 025 872 27
27
E930A457
27 Connect the adapter harnesses.
Saab 9-5 M01-
28 32 025 872
29.1-29.4
28.1-28.14
E930A458
Fit the keypad in accordance with one of the alternatives.
Saab 9-5 M01-
32 025 872 29
28.1-28.4
A
A
C
D
B
E
28 Fitting the keypad, alternative 1:
Important
This location is not an option for cars equipped
with ashtray, as the ashtray would come into contact with the keypad when extended.
28.1 Remove the storage compartment (A).
28.2 Automatic transmission: Remove the
surround (B).
28.3 Manual gearbox: Lift up the gear lever
gaiter (C).
28.4 Remove the cover's screws (D) and unplug
the connector (E).
Saab 9-5 M01-
E930A460
30 32 025 872
28.5
28.6
3mm (0.1in)
30mm
(1.2in)
20mm
(0.8in)
E930A461
28.7
E930A462
28.8
E930A463
28.5 Measure out the keypad location and drill a
3 mm hole.
28.6 Cut/drill a groove straight out.
28.7 Connect the keypad to the adapter harness.
28.8 Secure the wiring.
Saab 9-5 M01-
E930A459
32 025 872 31
28.9-28.12
A
A
C
D
B
E
28.9 Plug in the connector (E) and fit the cover's
screws (D).
28.10Manual gearbox: Fit the gear lever gaiter
(C).
28.11Automatic transmission: Fit the surround.
28.12Fit the storage compartment (A).
Saab 9-5 M01-
E930A464
32 32 025 872
28.13
28.14
E930A465
28.13Secure the keypad's wiring harness.
Important
Fasten the wiring harness correctly so that there is
no risk of it chafing or rattling.
28.14Fit the keypad.
Saab 9-5 M01-
E930A466
32 025 872 33
29.1
29.2
E930A467
29.3
E930A468
29.4
E930A469
29 Fitting the keypad, alternative 2:
29.1 Carefully prize out the switch panel and
route the keypad cable between the switch
panel and the dashboard.
29.2 Fit the keypad.
29.3 Connect the keypad to the adapter harness.
29.4 Secure the wiring.
Saab 9-5 M01-
E930A470
34 32 025 872
31
30
E930A472
E930A471
32
33
A
E930A473
30 Secure the wiring together with the car's wiring
harness.
Important
Fasten the wiring harness correctly so that there is
no risk of it chafing or rattling.
31 Fit the sun visor's screws.
32 Fit the lower section of the trim in place, fit the
clip (A) with the loop down in the trim and press
the trim into all of the clips.
WARNING
Take care not to damage or loosen the energy
absorbers. Damaged or loosened energy absorbers must not be refitted. In appropriate cases, the
whole of the headlining must be replaced. A damaged energy absorber could provide reduced protection to the head in the event of impact.
33 Fit the cover to the fuses.
Saab 9-5 M01-
E930A474
32 025 872 35
34
B
B
B
A
C
D
E930A475
34 Fit the lower section of the dashboard:
34.1 Connect the floor lighting (D).
34.2 Fit the clip (C).
34.3 Fit the lower panel (B).
34.4 Fit the data link connector (A)
Saab 9-5 M01-
36 32 025 872
M01-05
36.1
35
E930A476
M01-05
36.2
E930A477
M01-05
36.3
E930A478
35 Fit the ACC panel.
36 Fit the radio/navigation unit, M01-05:
36.1 Plug in the connectors.
36.2 Fit the compartment.
36.3 Insert the unit.
Saab 9-5 M01-
E930A479
32 025 872 37
M0637.1
M0637.2
E930A480
37 Fit the radio/navigation unit, M0637.1 Plug in the connectors.
37.2 Insert the unit, fit the screws and the plugs.
Saab 9-5 M01-
E930A481