M200F Estrusori ENG

EXTRUDER
FOR COLD EXTRUSION
!!!
The Marvalglass cold extruders are used for the final sealing by hand of panels of insulating glass with polysulphide and silicone products
!!
The articles in the production are the following :
M200/FT - Two-Sealants Extruder For Cold For Polysulphide (Thiokol)
Of 200 Lt.
M200/FS - Two-Sealants For Cold For Structural Silicon
Of 200 Lt
M200/FSM - Monocomponent Extruder For Silicon
Of 200 Lt
M20/FSM - Monocomponent Extruder For Silicon
Of 20 Lt
M200/FT
Two-Sealants Manual Hydraulic Extruder Of 200 Lt
!!
for polysulphide (Thiokol) at high viscosity
Drums for basis comp. of lt. 200 - catalyst comp. of about 20 lt.
It allows to apply manually the sealant to the final closure of insulating glass.
Structure mounted on swivel wheel to facilitate the movement.
Volumetric pump to take the product.
Dosing system with a lever mechanism which allows the adjustment of the ratio between the two
components.
Hydraulic motor of pump of A Comp. Hydraulic power plant with pump, adjustable volume.
Pneumatic lifting device of the basis and catalyst product.
Pneumatic motor of pump of B Comp.
Mixing device with manual gun AP.
Pressure checking by manometers with security device.
High pressure hoses. Electrical panel with all controls
Heater plate and temperature checking It is possible to wash the mixer/gun with the basis
component with a simple operation or use the FREEZER (supplied separately).
Volt. 400 HZ 50/60 Trifase + N - Potenza KW 4 - Bar da 2 a 8
Dimensioni D’ingombro: 1500 x 1300 x 2400 mm.
Marvalglass Srl Si Riserva Il Diritto Di Modificare I Dati In Questi Fogli Di Descrizione Generale. La Macchina Mostrata È Una
Semplice Linea Guida, Potrebbe Includere Accessori Opzionali E Variare In Base All'altezza Massima Di Lavoro.
!
M200/FS
Two-Sealants Manual Hydraulic Extruder Of 200 Lt
for structural silicon at high viscosity.
It allows to apply manually the sealant to the final closure of insulating glass.
Structure mounted on swivel wheel to facilitate the movement.
Volumetric pump to take the product.
Dosing system with a lever mechanism which allows the adjustment of the ratio between the two components.
Hydraulic motor of pump of A Comp. Hydraulic power plant with pump, adjustable volume.
Pneumatic lifting device of the basis and catalyst product.
Pneumatic motor of pump of B Comp.
Mixing device with manual gun AP.
Pressure checking by manometers with security device
Dosing and pressure control with proportional valve.
High pressure hoses in Teflon. Electrical panel with all controls.
Heater plate and temperature checking.
!!
!
Volt. 400 HZ 50/60 Three phase + N - Power KW 4 - Bar from 2 to 8
Dimensions: 1500 x 1300 x 2400 mm.
M20/FSM
Monocomponent Manual Pneumatic Extruder
Of 20 Lt For Silicon
Drum of lt. 20. Pneumatic pump to take the product.
Lifting device with 2 pneumatic cylinders.
High pressure hose in Teflon. Gun with rotatine joint.
!
M200/FSM
Monocomponent Manual Hydraulic Extruder Of 200 Lt For Silicon.
It allows to apply manually the sealant to the final closure of insulating glass.
Structure mounted on swivel wheel to facilitate the movement.
Volumetric pump to take the product.
Hydraulic motor of pump. Hydraulic power plant with pump, adjustable volume.
Pneumatic lifting device.
Manual gun AP
Pressure checking by electronic manometer with security device.
High pressure hoses in Teflon. Electrical panel with all controls.
Heater plate and temperature checking.
!!
!
Volt. 400 HZ 50/60 Three phase + N - Power KW 4 - Bar from 2 to 8
Dimensions: 1300 x 1100 x 2400 mm.
MARVALGLASS
!
S.R.L.!
Via La Valle 47/49 - 22066 - Mariano Comense (CO) - ITALY
Tel. +39 031 744752 - Fax +39 031 751117
www.marvalglass.com - www.marvalglass.net
info@marvalglass.com - marvalgl@marvalglass.com - sales@marvalglass.com