Side Jamb Liner Replacement

Side Jamb Liner Replacement
for E-Series Double-Hung
Thank you for choosing Andersen.
For questions call 1-888-888-7020. For more information and/or guides visit www.eaglewindow.com
Please leave this guide with building owner.
▶▶ Read guide from beginning to end before starting maintenance procedure. Read all warnings and cautions during unit maintenance.
▶▶ For information, calculating, and design pressure ratings for E-Series windows and doors go to
www.eaglewindow.com/Wintelligence/Design-Pressure-Estimator.aspx
▶▶ Check with your local building code official to identify and confirm compliance with local building code requirements.
Parts Included
(1) Side Jamb Liner
Tools Needed
∙∙ Safety Glasses
∙∙ Flat Blade Screw Driver
∙∙ Finish Nailer (for monumental units only)
∙∙ Pliers (for monumental units only)
∙∙ Putty Knife (for monumental units only)
Supplies Needed
∙∙ Denatured Alcohol
∙∙ Clean Cloth
Windows and doors can be heavy. Use safe
lifting techniques and a reasonable number of
people with enough strength to lift, carry and
install window and door products to avoid injury
and/or product damage.
Side Jamb Liner
Use caution when working at elevated
heights and around unit openings. Follow
manufacturers’ instructions for ladders and/
or scaffolding. Failure to do so may result in
injury or death.
“Andersen” and all other marks where denoted are trademarks of Andersen Corporation and its subsidiary. ©2013 Andersen Corporation. All rights reserved.
Follow manufacturers’ instructions for hand
or power tools. Always wear safety glasses.
Failure to do so may result in injury and/or
product damage.
9 0 6 9 1 5 8 BA
Revised 06/03/13
1
2
Interior Side Stop
Interior
Interior
Putty Knife
Lock
Handles
Interior Side Stop
Pliers
4 Inches
For Monumental Only
▶▶ For single and double hung units proceed to step 2.
Pry interior side stop away from frame. Repeat on opposite side. Remove any nails from frame and
interior side stops.
Unlock window and raise bottom sash 4".
3
4
5
Interior
Interior
Interior
Bottom Sash
Lock
Handles
Bottom Sash
Single Hung and Monumental Only
Rotate and hold lock handles toward center
while tilting sash in 90 degrees.
7
6
Interior
Pivot bottom sash to remove from window
frame as shown. Place sash on clean flat work
surface, exterior side up.
▶▶ For double hung units proceed to step 6.
6 Inches
8
Tilt
Latch
Interior
Remove sash stop from the side jamb.
Interior
Top Sash
Tilt
Latches
Lower top sash 6”.
9 0 69158
Slide tilt latches inward while tilting sash in
90 degrees.
2
Pivot top sash to remove from window frame
as shown. Place sash on clean flat work
surface, exterior side up.
9
Interior
Pocket Cover
Grasp jamb liner pocket cover at bottom and pull outward and down
from behind head stop to remove and save for reuse.
10
Interior
Balance shoes are under
high tension. Use flat blade
screwdriver with long handle
so that both hands can be
used to release balance
tension. Suddenly releasing
balance shoe could damage
window unit.
Balance
Shoe
Cam in locked position
Shoe
Balance
Cam
Cam in unlocked
(travel) position
Flat Blade
Screwdriver
2nd
1st
Insert flat blade screwdriver into cam slot, apply firm downward pressure, and rotate 1/4 turn. Hold firmly allowing shoe to rise until it stops. Repeat for
other three balances.
11
12
Interior
Interior
Outside Jamb Liner
Insert
12 Inches
Sill
Cushion
Flat Blade
Screwdriver
Remove existing sill cushion and save for reuse.
9 0 69158
Slide outside side jamb liner insert up 12”.
3
13
14
Interior
Interior
Jamb
Liner
Head Stop
Side Jamb Liner
Jamb Liner
Remove side jamb liner working from bottom to top, prying jamb liner
edge from frame to disengage as shown.
Pull side jamb liner down slowly, while supporting head stop and remove
from frame. Dispose of side jamb liner properly.
15
16
Interior
Interior
Interior
Side
Stop
Jamb Liner
Insert new side jamb liner behind head stop.
Position side jamb liner in frame, locking front lip behind interior side stop.
17
18
Interior
Interior
Balance
Shoe
Locked
Position
Shoe
Balance
Cam
Flat Blade
Screwdriver
Unlocked
Position
Jamb Liner
Re-engage side jamb liner, working from bottom to top, pressing jamb
liner edge into frame to engage as shown.
9 0 69158
Insert flat blade screwdriver into cam and pull down until shoe is aligned
with shoe on opposite side. Rotate cam ¼ turn to lock.
4
19
20
Interior
Interior
Jamb Liner
Exterior Insert
Clean Cloth and
Denatured Alcohol
Slide outside side jamb liner insert down to sill.
21
Clean area with a clean cloth and denatured alcohol.
22
Wide End
Interior
Interior
Jamb Side
LinerCutting
Pliers
Channel
Balance
Shoes
Sill Cushion
Checkrail
Weatherstrip
Sill Cushion
Pivot Pin
Position wide end of sill cushion in jamb liner channel, adhesive side
down, and press into place.
Rotate top sash to engage pivot pins into balance shoes of exterior
channel. Push down until both pivot pins are fully engaged.
23
24
Interior
Interior
Tilt
Latches
Beveled Side
Head
Stop
Jamb Liner
Pocket Cover
Interior
Channel
Tilt Latches
Tilt sash up, retracting tilt latches by sliding inward. Release tilt latches
to re-engage sash in frame. Verify top sash operation. Repeat steps
22-23 if sash does not operate correctly.
9 0 69158
Insert top of jamb liner pocket cover, beveled side toward exterior, into
interior channel, sliding it up behind head stop. Press jamb liner pocket
cover firmly into place, starting at top, zippering down full length.
▶▶ For double hung units proceed to step 26.
5
25
26
Interior
Interior
Balance
Shoe
Interior
Channel
Sash Stop
Pivot Pin
Single Hung and Monumental Only
Replace sash stop in the side jamb.
Rotate bottom sash to engage pivot pins into balance shoes of interior
channel. Push down until both pivot pins are fully engaged.
27
28
Interior
Interior
Lock
Handles
Lock
Handles
Tilt sash up, retracting tilt latches by rotating lock handles toward
center, then release lock handles to re-engage sash.
Verify sash operation. Repeat steps 26-27 if sash does not
operate correctly.
29
30
31
Interior
Interior
Interior
Interior
Side
Stop
Lock
Handles
Lock
Handles
For Monumental Only
Verify sash operation. Repeat steps 30-31 if
sash does not operate correctly.
9 0 69158
Close and lock sash.
▶▶ Side jamb liner replacement procedure is complete for single and double hung units.
▶▶ For monumental units proceed to step 31.
6
Reapply interior side stop on frame. Repeat
on opposite side. Fasten with finish nailer.
▶▶ Side jamb liner replacement procedure is complete for monumental units.