F820 Instruct BOOK p1

INSTRUCTIONS
INSTRUCTIONS
F820
Retractable Gate
Retractable Gate
Important: Keep instructions for future reference
Important: Keep instructions for future reference
Complies with Standards: ASTM F1004-04
Complies with Standards: ASTM F1004-07
Read INSTRUCTIONS thoroughly before assembling and installing gate.
Read INSTRUCTIONS thoroughly before assembling and installing gate.
Patent No. 1/604,922
The plastic parts are made of fibreglass-armed polyamide, Polypropylene and Polyester.
Plastic parts: Nylon & Polyoxymethylene (POM) materials.
Mesh fabric made of 40% polyester and 60% non-toxic PVC coating.
Other components are made of steel and aluminium.
The materials are used for their durability and resistance.
Spacers made of ABS (Acrylonitrile Butadiene Styrene).
•
•
•
•
•
MAINTENANCE & CARE
•
•
Gate must be fitted according to instructions, to ensure it works correctly.
Regularly check gate to ensure it is fitted properly and securely. Adjust as required.
Regularly check that brackets, brace and hooks are securely in place.
If gate is used outdoors, bring inside and keep out of rain, hail, snow or below freezing conditions.
Do not use the safety gate if any components are damaged or missing.
To clean, wipe surface with a damp cloth or sponge using mild detergent and warm water.
Never clean with abrasive, ammonia based bleach based or spirit type cleaners.
Any additional and replacement parts should be obtained from Tee-Zed Products.
•
•
•
•
•
CONTACT DETAILS
TEE-ZED PRODUCTS PTY LIMITED OR TEE-ZED PRODUCTS (N.Z.) LIMITED ACCEPTS NO RESPONSIBILTY FOR ANY LOSS OR DAMAGE SUFFERED BY ANY
PERSON AS A RESULT OF THE USE OR MISUSE OF THESE GOODS. IN THE CASE OF ANY DEFECT IN THE GOODS, TEE-ZED’S LIABILITY SHALL BE LIMITED
SOLELY TO REPLACEMENT OF THE DEFECTIVE GOODS.
Dream Baby® products by
Tee-Zed Products Pty Ltd, PO Box 2022,
Bondi Junction NSW 1355
Australia Ph: (02) 9386 4000
Made in China
©2009 Tee-Zed Products Pty Ltd
Tee-Zed Products (N.Z.) Ltd PO Box 64013,
Botany Town Centre, Auckland
New Zealand Ph: (09) 274 8788
info@tee-zed.com.au
www.dream-baby.com
www.dream-babyblog.com
Patent No. 1/604,922
WARNING
COMPOSITION
•
•
•
•
•
•
F820
•
•
This gate is suitable for openings up to 140cm (55”).
This gate is NOT suitable for openings wider than
140cm (55”).
This product is intended for use with children from
6 - 24 months.
Never leave child unattended. This product may
not prevent all accidents.
This product is not to be used with a child able to
climb over or dislodge/open the gate.
WARNING: Incorrect fitting or positioning of this
safety barrier can be dangerous.
To prevent serious injury, never allow adults,
children or pets to climb over or under the gate, as
it may damage this safety gate.
The surfaces that the safety gate is to be fixed to
must be suitable for the purpose and must be
structurally sound.
NOTE: Do not use this gate if it can’t be installed to
walls, door frames or posts – tightly and flatly.
DO NOT install this gate to hollow walls.
The clearance space between the Base of Casing
and the floor MUST NOT exceed 0.3cm (0.12”).
This safety gate must NOT be fitted across window
openings and the like.
NOTE: Never use without Locking Hooks.
Securely install and operate the gate according to
instructions to help prevent accidental injury.
•
•
•
•
•
•
•
Do not use the safety gate if any components are
damaged or missing.
Install this gate away from heaters and other
sources of heat.
This gate must NEVER be used as a pool or
pond barrier.
Gate is not meant to replace proper
adult supervision.
Always check that gate is locked after closing gate.
If the gate is used at the bottom of the stairs to
prevent the child from climbing up the stairs, it
must be placed on the lowest stair.
If the gate is to be used at the top of the stairs to
prevent the child from falling down the stairs, it
must not be placed on any stair below the level of
the top stair.
At the top of landing, position the gate 15cm (6”)
away from the top step.
WARNING – The position of the safety
barrier in relation to the stairs may
have an adverse effect on your
child’s safety
OPERATION
6. The Retractable Safety Gate is easy to use and allows for one-handed operation by adults.
To close the Retractable Gate
• Release the gate by pushing down the Release Button (Z) (see 6-1), and while maintaining downward pressure,
turning the Release Button (Z) clockwise (see 6-2).
• The gate is now unlocked, and the Release Button (Z) can be released.
• Pull out the Safety Barrier (A) (see 6-3) without stopping and hook the Locking Catches (F) over the Locking Hooks (E).
• Retractable Gate automatically locks closed.
WARNING – AFTER CLOSING Retractable Safety Gate, ALWAYS CHECK THAT THE GATE IS LOCKED.
To open the Retractable Gate
•
•
•
•
Release the gate by repeating the operations in 6-1 and 6-2.
Unhook the gate, hold handle while it retracts back into its casing.
Please note that the noise while retracting gate is meant as a warning signal.
To avoid the noise, simply keep button depressed while retracting the Safety Gate.
6-1
7
6-2
6-3
5
1. PARTS LIST
INSTALLATION
4. Installing the Locking Hooks &
Locking Brackets
Align the grooved line marking on Face of Casing (Y) to the
arrow show on the Upper Locking Bracket (B) (see 5-1).
Snap the gate into place until you hear a clicking sound (see 5-2).
Fit the Locking Brace (C) over the Upper Locking Bracket (B) (5-3).
The Locking Brace (C) will provide a dual-locking system (5-4).
To detach the Safety Barrier mechanism, first slide off the
Locking Brace (C) from the Upper Locking Bracket (B) (5-5).
Push the latch on Locking Bracket (B) towards the wall and pull the Safety Barrier mechanism upward to release from
Locking Brackets (B & D) (5-6).
77.6cm (30.55”)
5. Fitting the Retractable Gate
6.8cm (2.68”)
81.2cm(31.97”)
0.3cm (0.12”)
Template (1 = Locking Brackets; 2 = Locking Hooks) (4-1).
Locate the frame/stud and overlay the Locking Bracket template
directly on it and install the Locking Brackets (B & D).
The clearance space between the Base of Casing (X) and the floor
MUST NOT exceed 0.3cm (0.12”) (4-2).
Overlay the Locking Hooks template directly on other side of
the wall/door opening and install the Locking Hooks (E).
Ensure that the Looking Hooks (E) and Brackets (B & D) properly
engage.
A
B
Safety Barrier
C
D
E
F
G
H
Locking Brace (x1)
Upper Locking Bracket (x2)
Lower Locking Bracket (x2)
Locking Hook (x4)
Locking Catch
Screws 4 x 25mm (0.157 x 0.984”) (x16)
Plugs (x16)
I
J
B
G
C
Z
Y
I
Bracket Spacer
[1.27cm (1/2”) sold separately]
J
Backing Bracket Spacer
[I+J= 1.91cm (3/4”) sold separately]
K
Hook Spacer
[1.27cm (1/2”) sold separately]
L
Backing Hook Spacer
[K+L= 1.91cm (3/4”) sold separately]
M
X
Y
Z
Screws 4 x 45mm (0.157 x 1.771”) (x16)
A
Base of Casing
Face of Casing
Release Button
F
G
E
NOTE: Safety Gate and all parts are removable, re-usable and relocatable.
Two sets of brackets, hooks and spacers are enclosed to conveniently set up a second location for the Safety Gate.
M
H
M
D
G
F G E
X
4
1
K
L
INSTALLATION
INSTALLATION
2. Best location for the Retractable Gate
Locate the best position for the Retractable Safety Gate which can be fitted in hallways / doorways (see 2-1 & 2-2)
and stairways (see 2-3, 2-4). Also decide which side to have opening handle prior to installation.
Bottom of stairs: If the barrier is used at the bottom of the stairs to prevent the child from climbing up the stairs,
it must be placed on the lowest stair (2-3).
Top of stairs: If the gate is to be used at the top of the stairs to prevent the child from falling down the stairs, it must
not be placed on any stair below the level of the top stair.
At the top of the landing, position the gate 15cm (6”) away from top step (2-4).
Decide which side is more convenient for opening this gate, handle to the left or right.
Always ensure that the Safety Barrier (A) is positioned according to the template.
2-1
3. Skirting boards (baseboards)
If there is a skirting board (baseboard) to which the Retractable Safety Gate is to be attached, build up the wall areas
equivalent to thickness of baseboard (skirting board) with Spacers (sold separately) (see configuration and measurements below (3-7).
Upper Locking Bracket (B) (3-3).
Make sure that the gate is mounted firmly and evenly in vertical position.
Upper Locking Hook (E) (3-4).
Make sure that the upper and lower Locking Hooks (E) are positioned to securely engage the Locking Catches (F).
Locking Hooks (E) can be mounted upright (3-5) or flat (3-6), depending on if Gate is mounted to inside of door frame or not.
NOTE: Never use Backing Spacers to mount Safety Gate or Locking Hooks on their own (3-8).
Backing Spacers must only be used in conjunction with Bracket and Hook Spacers.
3-3
Bottom of stairs
2-2
3-4
3-6
spacer
spacer
If the gate is used at the bottom of
the stairs to prevent the child from
climbing up the stairs, it must be
placed on the lowest stair.
3-5
2-3
Top of stairs
15cm
6”
If the gate is to be used at the top of
the stairs to prevent the child from
falling down the stairs, it must not be
placed on any stair below the level of
the top stair.
At the top of landing, position the gate
15cm (6”) away from the top step.
2-4
3-7
3. Installing the Retractable Gate
There are 3 grooved line markings on the Face of Casing (I), to allow
for 3 options to secure gate into its position. Grooved line marking is
to be lined up with the arrow on Upper Locking Bracket (B) to suit
direction for Safety Barrier (A) extension (see 3-1 & 3-2).
Hardware is required to install this gate.
Mounting materials used for fixing gate must be suitable for the
wall surface.
Mounting screws (G) supplied.
If mounting to concrete or brick walls, use supplied raw plugs (H).
J
Top view of gate
Side view of gate
I
K
I = 1.27cm (1/2”)
I+J = 1.91cm (3/4”)
K = 1.27cm (1/2”)
K+L = 1.91cm (3/4”)
3-8
J
2
JI
L
3
LK
L