Drill Unit Operator`s Manual

Transcription

Drill Unit
Operator’s Manual
997723
Original Issue Date of Manual
February 19, 2002
Any updated pages after this date will have the revision date printed on the bottom of the pages.
Table of Contents
Safety Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Safety-Alert Symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Prior To Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
During Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
While Transporting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Maintenance Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Tire Service Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Be Prepared For Accidents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Safety Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Using This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Terminology: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Serial Number Plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Record of Maintenance Performed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Assembly Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Before Beginning Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Press Wheel Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Optional Opener Shield Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Mounting the Hydraulic Row Marker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Wing Frame Row Marker Hydraulics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Centre Frame Hydraulic Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Assembly Conclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Distribution Kit Layouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
The following diagrams represent layouts of the Distribution Kits on the Xpress Air Drill Units. . .
21
Blockage Module Layouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
The following diagrams represent layouts of the Blockage Modules on the Xpress Air Drill Unit.
35
Operating Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Connecting the Air Cart to the Xpress Air Drill Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Initial Operating Check List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Hydraulic Lift System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Morris Xpress Drill Unit
997723
3
Table of Contents
Hydraulic Fold System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Xpress Air Drill Height & Leveling Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Seeding Depth Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Opener Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Soil Firming Device Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Rigid Scraper Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Maintaining Proper Pinch Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Checking For Loose Pinch Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Checking For Tight Pinch Point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Adding Or Removing Shims . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Unfolding And Folding The Xpress Air Drill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Unfolding Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Folding Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Lubrication Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
The following illustrations in this section show location of the areas needing lubricated and the
frequency.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Wheel Bearings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
At The End Of The Planting Season . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
At The Beginning Of The Next Planting Season . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Appendix Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Proper Bolt Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
SAE Fastener Torque Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Parts Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
The drawings and listings in this section represent all parts available for order. . . . . . . . . . . . 63
Frame & Main Frame Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Left Wing Frame Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Right Wing Frame Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
2-Point Hitch Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Slide Lock Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Centre Lift Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Centre Lift Spindle & Wheel Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Wing Lift Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
Wing Lift Spindle & Tire Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Main Frame Lift Hydraulics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Centre Frame Lift Hydraulics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Outer Wing Lift Hydraulics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
3 3/4" x 10" Hydraulic Cylinder (4431R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
4" x 10" Hydraulic Cylinder (4430R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Transport Lock Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
4
997723
Table of Contents
Main Frame Fold Hydraulics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .98
Centre Frame Fold Hydraulics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100
4" x 16" Hydraulic Cylinder (9725R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .102
All Purpose Heads Up Opener . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .104
All Purpose Heads Up Opener Press Wheel Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . .106
Press Wheel & Tire Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .108
Opener Shield Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110
Row Marker Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .112
Row Marker Mount Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .114
Row Marker Hydraulics on Main Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116
Row Marker Hydraulics on the Centre Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118
Wing Frame Row Marker Hydraulics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120
3" x 20" Hydraulic Cylinder (6633R) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
Light Kit Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .124
Decal Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126
Numerical Part Number Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
997723
5
Table of Contents
6
997723
Safety Section
For your safety and to develop a better understanding of
your equipment, thoroughly read the Operator’s Section of
this manual before operation.
Note: These rules and instructions are for the safety of all
personnel operating this machine and must be reviewed at
least annually.
Safety-Alert Symbols
Prior To Operation
The SAFETY-ALERT SYMBOL indicates that there is a
potential hazard to personal safety involved and extra
safety precautions must be taken. When you see this symbol, be alert and carefully read the notation that follows it.
Hazard control and accident prevention are dependent
upon the carefulness, awareness and proper training of the
personnel involved in the operation, transport, maintenance and storage of this equipment.
CAUTION
Before operating the machine, read and fully understand the Operator’s Manual. If you do not understand
any portion of this Operator’s Manual, contact your
MORRIS dealer for clarification.
1.
Do not wear loose-fitting clothing or clothing with loose
strings or straps which could get entangled in the
machines moving parts. Always wear long pants and
protective shoes.
2.
Securely support any machine elements that must be
raised for assembly, repair or adjustments. Use caution when working under or near these areas.
3.
After assembling, repairing or adjusting, make sure all
tools, parts, and rags are removed from the machine
before attempting to operate it.
4.
Check that wheel lug nuts or bolts are tightened to the
specified torque. Make sure the implement tires are
inflated evenly. Refer to the appendix for the torque
and inflation charts.
5.
Do not use the machine until you are sure the area is
clear, especially of children and animals.
6.
Make a visual inspection of the machine for any loose
bolts, worn or missing parts, and make necessary
repairs. Follow the lubrication instructions in the operating section of this manual.
This notation indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be used to alert you of unsafe
practices.
7.
Do not stand on or straddle the tongue when hitching
or unhitching the machine from the tractor. Do not
allow anyone to stand between the tongue or hitch and
the towing vehicle when backing up the machine.
Safety Rules
8.
Securely attach the machine to the towing vehicle.
Use a high strength, appropriately sized hitch pin and
secure with a suitable retaining device.
9.
Always use a safety chain with a tensile strength equal
to or greater than the gross weight of the machine and
any attachments when transporting. Provide only
enough slack in the chain to permit turning.
The following Safety-Alert Symbols are placed throughout
this manual for your personal safety. Be sure you and your
fellow workers follow them closely.
DANGER
This notation indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This signal word is limited to the most
extreme situations, typically for machine components
that, for functional purposes, cannot be guarded.
WARNING
This notation indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury, and includes hazards that are exposed
when guards are removed. It may also be used to alert
against unsafe practices.
CAUTION
Most accidents are the result of negligence and carelessness, caused by the failure of the operator to follow all the
safety precautions. Your machine has been designed with
many built-in safety features, but the following precautions
are mandatory to prevent such accidents.
Make sure that all personnel who use the machine, read
and fully understand how to operate the machine safely.
This Operator’s Manual is considered a part of the implement and should remain with it even when loaned or sold.
997723
7
Safety Section
While Transporting
CAUTION
Misuse or modification of this machine can cause serious personal injury or damage to the machine.
During Operation
1.
Always use flashing lights when traveling on a road or
highway, except where such use is prohibited by law.
2.
Comply with all state and local laws while transporting.
3.
Always use a slow moving vehicle emblem when
transporting. Keep the SMV emblem and all reflectors
clean and visible to warn other motorists of your presence.
1.
The machine should be operated only by a qualified
person who is familiar with the tractor, the machine,
and all the safety related requirements. Do not let children operate this machine.
4.
2.
Beware of bystanders, particularly children! Always
look around to make sure it is safe to move the
machine.
Latch tractor brakes together and stop slowly. Never
use independent braking with the machine in tow as
loss of control and/or upset of the machine can result.
5.
Never permit riders on the machine or on the tractor
during operation.
Always check the lug nuts for tightness, before transporting.
6.
Shift the tractor into a lower gear when transporting
down steep slopes or hills. Always keep the tractor in
gear when transporting down a slope. Do not coast.
3.
4.
Keep everyone clear of the machine when folding or
unfolding the wings.
5.
Always have the machine attached to the tractor or
another implement when folding or unfolding the
wings.
7.
Do not pull the machine on any public roadways with
any vehicle, except a tractor of the size required for
field operation.
6.
When unfolding the wings, make sure there is adequate room to unfold the machine.
8.
7.
Always shut off the tractor and shift into park when
leaving the tractor. Remove the key when leaving the
tractor unattended.
Always use a safety chain with a tensile strength rating
equal to or greater than the gross weight of the
machine. Provide only enough slack in the chain to
permit turning. Do not use the safety chain for towing.
9.
ASAE Standards state that while transporting any
equipment that does not have brakes, the maximum
speed should NOT exceed 32 km/h (20 m.p.h.).
8.
Do not adjust, lubricate or repair the machine while it is
in operation.
9.
Use caution when working around hills. Be sure that
the slope is not so steep as to cause the machine or
tractor to turn over. On steep slopes, go up and down
the slope and use caution when turning the machine.
10. Use caution when operating near a ditch, hill, creek or
fences.
11. Following every 100 hours of operation, or as needed,
tighten all the nuts and bolts to the specified torque
listed in the appendix section of this manual.
WARNING
Escaping fluid under pressure can penetrate the skin
causing serious injury. Relieve pressure before disconnecting a hydraulic line or any other line. Tighten
all connections before applying pressure. Keep hands
and body away from pinholes and nozzles which eject
fluids under high pressure. Wear proper hand and eye
protection when searching for leaks. Use a piece of
cardboard or heavy paper instead of your hand to
locate the leak. If ANY Fluid is injected into the skin, it
must be surgically removed within a few hours by a
doctor familiar with this type of injury or gangrene may
result.
8
997723
10. Always check for overhead obstacles during transport.
Know the overall height, width, length, and gross
weight of the machine and the towing vehicle before
transporting.
Maintenance Safety
1.
Understand the service procedures before doing any
work on the machine. Keep the area clean and dry.
2.
Securely support any machine components that must
be raised for service or adjustments. Use caution
when working under or near these areas.
3.
Never lubricate or service the machine while it is moving.
4.
Disengage all power and operate controls to relieve
pressure.
5.
Lower the machine to the ground, stop the engine, and
remove the key, before performing any service or
adjustments.
6.
Keep all parts in good condition and properly installed.
Replace worn or broken parts immediately. Remove
any buildup of grease, oil, or debris.
7.
Check all bolts and nuts frequently to be sure they are
tightened to the specifications.
Safety Section
8.
9.
Make sure all hydraulic line connectors are tight, and
all hydraulic hoses and lines are in good condition
before applying pressure to the system.
Perform the maintenance instructions described in this
manual according to the schedule provided. If major
repairs are ever needed or assistance is desired, contact an Authorized MORRIS Dealer. To ensure optimum performance and safety, always purchase
genuine MORRIS replacement parts and accessories.
Using unapproved replacement parts and accessories
could void the warranty provided by MORRIS.
10. Do not modify or permit any modification to this
machine or any of its components, without first consulting your authorized MORRIS Dealer.
Tire Service Safety
1.
2.
Do not attempt to mount a tire unless you have the
proper equipment and experience to perform the job
safely.
Always maintain the correct tire pressure. Do not
inflate tires above the recommended pressure.
3.
When inflating tires, use a clip-on chuck and extension
hose long enough to allow you to stand off to one side
and NOT in front or over the tire and wheel assembly.
Use a safety cage if available.
4.
Explosive separation of a tire and rim can cause serious injury or death.
5.
Check tires for low pressure, cuts, bubbles, damaged
rims or missing lug bolts and nuts, before and after
each use.
2.
Keep all safety signs clean and legible.
3.
Replace all damaged or missing safety signs. Order
new safety signs from your nearest MORRIS dealer.
4.
When ordering new or replacement components make
sure the correct safety sign is affixed to the new part, if
not be sure to order a replacement safety sign to
install.
5.
Refer to this section or safety sign placement in the
parts section of this manual for the proper sign placement location. To install new safety signs:
6.
Clean the area the sign is to be placed on.
7.
Spray soapy water on the surface where the sign is to
be placed.
8.
Peel the backing from the sign, and carefully place on
the wet surface, when placement is in the correct position, press firmly onto the surface.
9.
Squeeze out the air bubbles with the edge of a credit
card.
The types of safety signs and locations on the machine are
shown in the following illustrations. Good safety requires
that you familiarize yourself with the various safety signs,
the type of warning and area or particular function that
requires your SAFETY AWARENESS.
Be Prepared For Accidents
1.
Review and be aware of what to do in the event of an
accident or fire.
2.
Keep a first aid kit and a fire extinguisher handy.
3.
Keep an up to date list of emergency phone numbers
for doctors, ambulance, hospital, police, and fire
departments near your phone.
4.
Wear close fitting clothing and safety equipment that is
appropriate for the job.
5.
Use a seat belt when you operate a tractor with a rollover protective structure (ROPS) to minimize the
chance of injury from an accident such as an overturn.
6.
DO NOT use a seat belt if you are operating a tractor
without a ROPS.
Safety Signs
1.
Your machine comes equipped with all the safety signs
in place. They were designed to help you safely operate your machine. Read and follow their directions
completely.
997723
9
>
Figure 1
Safety Sign Placement
06149
Safety Section
10
997723
Safety Section
Red Reflective Tape
Orange Reflective Tape
2 997662
1 997661
3 997043
01437
4 997408
01443
5 997313
02156
6 997322
01445
7 997318
01456
8 997323
01444
9 997311
01438
10 997052
01457
11 997324
01458
12 7001
01464
Amber Reflective Tape
13 997663
997723
11
Safety Section
12
997723
Introduction
Congratulations on the purchase of your new MORRIS
product. We welcome you to the growing number of satisfied MORRIS customers. Your new product has been engineered and manufactured with quality and service as our
top priority. It should give you years of service with routine
maintenance.
We especially want to call your attention to Safety.
Although your machine was designed with the safety of the
operator in mind, accidents can still happen, so PRACTICE
ALL SAFETY PRECAUTIONS.
Using This Manual
This Operator’s Manual is designed to help familiarize you
with safety, assembly, operation, adjustments, troubleshooting, and maintenance of your new MORRIS product.
Read this manual and follow the recommendations to help
ensure safe and efficient operation. After reading this manual, keep it in a convenient place for quick and easy reference should any question arise.
05959
Figure 2
Serial Number Plate Location
Serial Number Plate
Refer to Figure 2 for the location of your serial number.
The information contained within this manual was current
at the time of publication. Some parts may change slightly
to assure you the best performance.
For prompt service, always use the serial number and
model number when ordering parts from your MORRIS
Dealer. Be sure to include these numbers in all correspondence.
To order a new Operator’s Manual contact your authorized
MORRIS Dealer or write to the address listed at the end of
this page. Always include the model and serial numbers of
your machine.
MORRIS and your local MORRIS Dealer want you to be
satisfied with your new machine. If for any reason you are
not satisfied with the service received, the following actions
are suggested:
Terminology:
1.
Discuss the matter with your local dealership Service
Manager to make sure they are aware of any problems you may have and give them the opportunity to
correct them.
2.
If you are still not satisfied, seek the Owner or General
Manager of the dealership, explain the problem and
request assistance.
3.
For further assistance, your local dealership will be
able to contact the local MORRIS District Manager.
Right or Left as listed in this manual is determined by
standing to the rear of the machine and facing the direction
of travel.
Definitions:
Note: A special point of information to its preceding topic.
The authors intention is that you read carefully and note
the information before continuing.
IMPORTANT: Information related to its preceding topic,
that the author believes would be of use.
Again Thank You for choosing MORRIS.
Owner Assistance
If customer service of repair parts are required for your
machine, please contact your local MORRIS Dealer. They
have trained personnel, repair parts, and the equipment
needed to repair your product.
These parts have been specially designed for your
machine and should only be replaced with genuine MORRIS REPLACEMENT PARTS. Remember routine maintenance to your product can save on costly repairs and
valuable downtime.
997723
13
Figure 3
Machine and Component Identification
06150
Introduction
14
997723
Introduction
For your convenience, use the following area to record all
your important information regarding your machine. If it
becomes necessary to contact MORRIS, have the model
number, size, serial number, dealer name where it was purchased, and the date of purchase.
Record of Maintenance
Performed
Model Number
Serial Number
Dealer Name
Dealer Phone
Date Purchased
Options Purchased
Additional Notes
997723
15
Introduction
16
997723
Assembly Section
Before Beginning Assembly
This assembly section is a step by step procedure to aid in
proper assembly of your new MORRIS Xpress Air Drill.
Before beginning actual assembly, this entire section
should be read carefully and fully understood.
Carefully unpack all the parts and hardware included and
verify nothing was damaged or lost in shipping.
All bolts and nuts need to be used in the proper locations in
which they were designed, to prevent damage to the
Xpress Air Drill. When two or more bolts are used to attach
a part, always insert the bolts and loosely tighten the nuts.
Once the correct placement has been achieved, tighten the
nuts evenly to prevent misalignment or distortion of the
parts.
through the rear press wheel frame assembly (#2), if not
already in place, then align the rear press wheel frame
assembly in the press wheel frame swivel. Insert the 3/4" x
5 1/2" hex bolt (#3) through the swivel and press wheel
frame assembly and attach and tighten the 3/4" lock nut
(#4).
Optional Opener Shield
Assembly
1.
Insert a 3/8” x 4 1/4” carriage bolt (#1) as shown in Figure 5, through the back of the opener mount. Place a
mounting clip (#3), and a lock nut (#4) on the carriage
bolt, but do not tighten the lock nut all the way.
For the proper torque values, refer to the appendix.
Your new MORRIS Xpress Air Drill was shipped to you
almost completely assembled for your convenience. The
only items that were not fully assembled are the wing press
wheels, which could not be installed at the factory due to
over width limitations.
05953
Figure 5
Opener Shield Assembly
2.
Slide an opener shield (#2) between the mounting clip
and the opener mount. Tighten the lock nut (#4) when
the shield is in position.
3.
When attaching two shields together, place a tie strap
(#6) over the holes on the ends of each opener shield
and insert 3/8” x 1” hex bolts (#5) and lock nuts (#4).
Mounting the Hydraulic Row
Marker
05961
Figure 4
Press Wheel Assembly
1.
Mount the row marker (#1) as shown in Figure 6, to
the Xpress Air Drill frame using a 3/4” x 8 3/4” x 7 13/
16” u-bolt (#7), a flat washer (#4), lock washer (#3)
and a hex nut (#2) on left end of the marker frame.
Press Wheel Assembly
Insert the clamp bushing (#1), as shown in Figure 4,
997723
17
Assembly Section
2.
Use 3/4” x 2 1/2” hex bolts (#8), lock washers (#3) and
hex nuts (#2) on the right end of the marker frame.
2.
Connect a 1/4” x 200” hose (30’ Xpress Air Drill) or a 1/
4” x 263” hose (#2) (40’ Xpress Air Drill), to the elbow
in the rod end of the row marker cylinder.
3.
4” x 240” hose (#3) (40’ Xpress Air Drill), to the elbow
in the base end of the row marker cylinder.
4.
Route the loose ends of hoses (#2) & (#3) toward the
centre of the Xpress Air Drill.
5.
Place pipe clamps (#6) over the hoses and insert a 3/
8” x 2 1/2” hex bolt (#4) with a 3/8” lock washer (#5),
through the pipe clamp and the bracket on the frame.
Centre Frame Hydraulic
Assembly
1.
Insert 90 degree straight thread elbows (#1) as shown
in Figure 8 on page 19, into the sequence valve (#10).
2.
Bolt the sequence valve (#10) to the valve mount (#5),
using 3/8” x 2” hex bolts (#6), flat washers (#11) and
lock nuts (#9).
3.
Attach the valve mount to the frame, using 3/8” x 1”
hex bolts (#12), flat washers (#11) and lock nuts (#9).
4.
Connect hose (#3) coming from the right wing, to the
right side of a union tee (#8).
5.
Connect hose (#2) coming from the right wing, to the
right 90 degree elbow in the sequence valve.
6.
Attach a 1/4” x 200” hose (30’ Xpress Air Drill) or a 1/4”
x 263” hose (#2) (40’ Xpress Air Drill), to the left 90
degree elbow in the sequence valve.
7.
4” x 240” hose (#3) (40’ Xpress Air Drill), to the left
side of the union tee (#8).
8.
Attach a 1/4” x 100” hose (30’ Xpress Air Drill) or a 1/4”
x 173” hose (#6) (40’ Xpress Air Drill), as shown in Figure 9 on page 20, to the 1/4” x 200” hose (#4).
9.
4” x 173” hose (#6) (40’ Xpress Air Drill), as shown in
Figure 9 on page 20, to the 1/4” x 234” hose (#7).
05962
Figure 6
Mounting the Row Marker
Note: Hex bolt (#5) and nut (#6) are left loose until the ubolt (#7) is in place and tight, then the hex bolt (#5) and nut
(#6) can be tightened. Make sure the u-bolt (#7) has been
inserted through the slotted hole in the marker linkage
mount .
Wing Frame Row Marker
Hydraulics
1.
Insert 90 degree straight thread elbows (#1), as shown
in Figure 7, into the row marker cylinder.
10. Route hoses (#4) and (#7) through the tongue. Connect the end of hose (#4) to the front of the union tee,
and attach the end of hose (#7) to the 90 degree
elbow located in the bottom of the sequence valve.
11. Attach male connectors (#2) and male half hydraulic
couplers (#1) as shown in Figure 9 on page 20, to the
ends of hoses (#6). These hoses are routed through
the tongue to the front of the Xpress Air Drill.
Assembly Conclusion
05956
Figure 7
Row Marker Hydraulics on the Wing Frame
18
997723
1.
Your Xpress Air Drill should now be fully assembled.
Before proceeding any further, it is a good time to
check that all of nuts and bolts are tight.
Assembly Section
05955
Figure 8
Row Marker Hydraulics on the Centre Frame
2.
Check all hydraulic fittings and hoses to insure that
they are tight.
3.
Make sure that all moving parts turn freely and do not
bind
4.
Read and understand the Operating Section of this
manual before continuing.
997723
19
Assembly Section
05673
Figure 9
Hose Routing for the Hydraulic Row Marker
20
997723
Distribution Kit Layouts
The following diagrams represent layouts of the Distribution
Kits on the Xpress Air Drill
Units.
997723
21
06066
Figure 10
Primary Hose Diagram on Air Cart
(30’ Xpress Air Drill, 10” Spacing with 36 Openers)
06067
Figure 11
(30’ Xpress Air Drill, 7.5” Spacing with 48 Openers)
(40’ Xpress Air Drill, 10” Spacing with 48 Openers)
22
997723
06068
Figure 12
(40’ Xpress Air Drill, 7.5” Spacing with 64 Openers)
Note: Refer to the following pages for the primary and secondary hose lengths for your particular Xpress Air Drill. The
lengths are approximate and do not have to be exact.
IMPORTANT: Use only hot water for lubrication when connecting the Primary and Secondary hoses. Do not use any
type of petroleum based lubricant as this will damage the
hoses.
997723
23
PRIMARY AND SECONDARY HOSE LENGTHS
30FT - 10" SPACING - 36 RUNS
PRIMARY
SECONDARY #1
SECONDARY #2
SECONDARY #3
SECONDARY #4
SECONDARY #5
SECONDARY #6
SECONDARY #7
SECONDARY #8
SECONDARY #9
SECONDARY #10
LT WING LT MAIN
#1 - 96" #8 - 120"
N/R
N/R
RT MAIN RT WING
#2 - 120" #7 - 96"
N/R
N/R
06082
.
30FT - 7 1/2" SPACING - 48 RUNS
PRIMARY
SECONDARY #1
SECONDARY #2
SECONDARY #3
SECONDARY #4
SECONDARY #5
SECONDARY #6
SECONDARY #7
SECONDARY #8
SECONDARY #9
SECONDARY #10
LT WING LT MAIN CENTER RT MAIN RT WING
#1 - 96" #5 - 120" #8 - 120" #2 - 120" #7 - 96"
N/R
N/R
06081
24
997723
40FT - 10" SPACING - 48 RUNS
PRIMARY
SECONDARY #1
SECONDARY #2
SECONDARY #3
SECONDARY #4
SECONDARY #5
SECONDARY #6
SECONDARY #7
SECONDARY #8
SECONDARY #9
SECONDARY #10
LT WING LT MAIN CENTER RT MAIN RT WING
#1 - 120 #5 - 120" #8 - 120" #2 - 120" #7 - 120
N/R
N/R
06080
40FT - 7 1/2" SPACING - 64 RUNS
LT OUTER LT INNER LT MAIN CENTER RT MAIN RT INNER RT OUTER
#1 - 132"
#3 - 96" #6 - 120" #8 - 120" #2 - 120" #4 - 96"
#7 - 132"
PRIMARY
66"
60"
102"
76"
98"
60"
66"
SECONDARY #1
74"
60"
93"
66"
95"
60"
74"
SECONDARY #2
85"
66"
102"
69"
95"
66"
85"
SECONDARY #3
102"
78"
106"
59"
103"
78"
102"
SECONDARY #4
86"
80"
109"
57"
108"
80"
86"
SECONDARY #5
97"
72"
102"
66"
96"
72"
97"
SECONDARY #6
78"
60"
108"
66"
108"
60"
78"
SECONDARY #7
60"
60"
108"
60"
104"
60"
60"
SECONDARY #8
56"
60"
108"
69"
108"
60"
56"
SECONDARY #9
N/R
N/R
N/R
62"
N/R
N/R
N/R
SECONDARY #10
997723
25
26
06069
997723
Figure 13
30’ Xpress Air Drill, 10” Spacing with 36 Openers
06073
27
997723
Figure 14
28
06070
997723
Figure 15
30’ Xpress Air Drill, 7.5” Spacing with 48 Openers
06074
29
997723
Figure 16
30
06071
997723
Figure 17
06075
31
997723
Figure 18
32
06072
997723
Figure 19
06076
33
997723
Figure 20
34
997723
Blockage Module Layouts
The following diagrams represent layouts of the Blockage
Modules on the Xpress Air
Drill Unit.
997723
35
36
997723
06136
Figure 21
30’ Xpress Air Drill, 7.5” Spacing with 48 Openers (12 Run Blockage Module)
37
Figure 22
30’ Xpress Air Drill, 10” Spacing with 36 Openers (12 Run Blockage Module)
997723
06135
38
997723
06140
Figure 23
30’ Xpress Air Drill, 7.5” Spacing with 48 Openers (All Run Blockage Modules)
39
Figure 24
30’ Xpress Air Drill, 10” Spacing with 36 Openers (All Run Blockage Modules)
997723
06139
40
997723
06138
Figure 25
40’ Xpress Air Drill, 7.5” Spacing with 64 Openers (12 Run Blockage Module)
41
Figure 26
40’ Xpress Air Drill, 10” Spacing with 48 Openers (12 Run Blockage Module)
997723
06137
42
.
997723
06142
Figure 27
40’ Xpress Air Drill, 7.5” Spacing with 64 Openers (All Run Blockage Modules)
43
Figure 28
40’ Xpress Air Drill, 10” Spacing with 48 Openers (All Run Blockage Modules)
997723
06141
44
997723
Operating Section
Connecting the Air Cart to the
Xpress Air Drill Unit
1.
Back the air cart up to the Xpress Air Drill unit and connect the two point hitch to the arms on the rear of the
air cart. Secure the two point connection and fasten
the safety chain.
DANGER
Do not allow anyone to stand between the air cart and
the Xpress Air Drill unit when backing the cart up.
2.
3.
The hydraulics are marked with tags on the rear of the
cart. Match the hose ends on the Xpress Air Drill unit
when connecting them to the cart.
Raise the two-point lift on the rear of the cart and raise
the parking stand on the Xpress Air Drill unit.
Initial Operating Check List
Your MORRIS Xpress Air Drill has been manufactured and
assembled at the factory, utilizing optimum levels of quality
control standards. However, before taking the Xpress Air
Drill to the field, minor adjustments may be necessary for
your field conditions. The following check points will help
insure safe and efficient operation of your Xpress Air Drill.
1.
Read through the operating section and service your
machine accordingly.
2.
Pay special attention to all safety suggestions.
3.
Check the tire pressure. Tires should be equally
inflated.
4.
Visually inspect all opener assemblies. Check for freedom of movement on all moving parts.
DANGER
Always make sure the jack stand is lowered on the
Xpress Air Drill unit when unhooking the tractor from
the air cart.
Hydraulic Lift System
The rephasing lift system on the MORRIS folding Xpress
Air Drill has been filled with oil and purged of air before
leaving the factory. In the event of a hose rupture or cylinder replacement, the air trapped in the lines will need to be
purged from the system.
WARNING
causing serious injury. Relieve pressure before disconnecting hydraulic or other lines. Tighten all connections before applying pressure. Keep hands and
body away from pinholes and nozzles which eject fluids under high pressure. Wear proper hand and eye
cardboard or paper instead of your hand. If ANY fluid is
injected into the skin, it must be surgically removed
within a few hours by a doctor familiar with this type of
injury or gangrene may result.
The cylinders are purged by connecting the lift system
hoses to the tractor. Make sure the tractors reservoir is full
of the manufacturers recommended hydraulic oil. Raise the
unit and hold the tractor lever to allow oil to bypass and fill
each wing cylinder. Lower the unit making sure the cylinders actuate simultaneously throughout the stroke. If the
cylinders are not in unison, continue holding the cylinders
extended and cycling the oil to purge any remaining air.
CAUTION
If cylinders are not in unison do not attempt to fully
retract (lower the Xpress Air Drill). Damage to the centre lift may occur. Fully extend the cylinders (raise the
Xpress Air Drill) to cycle oil through the system, then
the cylinders should be in unison.
Do not loosen any hydraulic fittings. Recheck the tractors
oil reservoir to make sure it is within operating limits.
Prior to starting any field operation, verify that all lift cylinders are operating in unison. If the cylinders are not operating together, hold the cylinders fully extended to cycle the
oil through the lift system. During field operations with the
Xpress Air Drill, always fully raise the unit when making
turns. This will insure that the cylinders are working in unison and keep the Xpress Air Drill operating level.
Note: Retracting the cylinders during periods of storage
will prevent rusting of the shafts and subsequent damage
to the seals.
Hydraulic Fold System
Note: Keep all persons away from the Xpress Air Drill
when folding or unfolding.
The hydraulic fold cylinders on the MORRIS folding Xpress
Air Drill have been filled with oil and purged of air before
leaving the factory. In the event of a hose rupture or cylinder replacement, the air trapped in the lines will need to be
997723
45
Operating Section
purged from the system.
CAUTION
causing serious injury. Relieve pressure before disconnecting hydraulic or other lines. Tighten all connections before applying pressure. Keep hands and
body away from pinholes and nozzles which eject fluids under high pressure. Wear proper hand and eye
cardboard or paper instead of your hand. If ANY fluid is
injected into the skin, it must be surgically removed
within a few hours by a doctor familiar with this type of
injury or gangrene may result.
To purge the fold cylinders of air, unpin the rod ends of the
cylinders, position cylinders to allow for rod extension and
connect fold system hoses to the tractor couplers. Make
sure the tractor reservoir is full of the manufacturers recommended hydraulic oil. Fully extend and retract the cylinders
several times until the action is positive and immediately
responsive. Do not loosen or crack any hydraulic fittings.
Recheck the tractor reservoir to make sure it is within operating limits. Reconnect the cylinders to the Xpress Air Drill.
46
997723
Operating Section
Xpress Air Drill Height & Leveling Adjustments
The top parallel link as shown in Figure 29, must maintain
the 3/4-1" measurement from the parallel link stop during
planting, or the opener will not function properly. To
increase the distance from the top parallel link and the parallel link stop, simply lower the Xpress Air Drill. Raising the
Xpress Air Drill will decrease the distance between the link
and the stop.
2.
Note: The stroke control segments (cylinder stops) must
be installed only on the two centre lift cylinders. Do not
install segments on the wing cylinders. The two centre lift
cylinders will control the depth of the entire Xpress Air Drill.
3.
After the stroke control segments (depth stops) have
been installed on the two centre lift cylinders, check
the measurement on the openers toward the outside
on the ends of the wings. The measurement on the
openers at the ends of the wings should also be 3/4" to
1". If the measurements are not the same, adjust the
wings as shown in Figure 30 on page 48, to achieve
the proper measurement on the opener.
4.
Use the lift system to maintain proper Xpress Air Drill
height in soft or loose soils.
5.
When changing fields or different soil conditions (conventional to no-till or loose vs. firm soil), the depth settings should be checked again.
Note: When the Xpress Air Drill is shipped new from the
factory, stroke control segments (cylinder stops) are
shipped with it. These segments are used to maintain the
proper height when drilling.
1.
Lower the Xpress Air Drill down to achieve the 3/4" to
1" measurement between the top parallel link and the
parallel link stop during drilling. Check this measurement on the inside openers toward the centre of the
Xpress Air Drill.
Note: The when leveling the Xpress Air Drill from front to
rear, always level the centre main frame of the Xpress Air
Drill. The tongue may not be parallel to the ground when
the centre frame is level.
When the desired planting depth and the 3/4" to 1"
measurement are achieved, install the stroke control
segments (cylinder stops) on the two centre lift cylinders.
05006
Figure 29
Opener Adjustments
997723
47
Operating Section
05963
Figure 30
Leveling the Wings (Side-to-Side)
Seeding Depth Adjustment
The seeding depth of each opener is controlled by the position of the depth cam assembly located on the back of the
opener frame, as shown in Figure 31. To change the setting, pull the spring-loaded D-handle out of the notch while
rotating the cam to a different setting, release the D-handle
in the new notch. To decrease the seeding depth, rotate the
cam to a notch more forward.
Note: Adjusting the opener down pressure does not
change the seeding depth. The seed depth is controlled by
the adjustment on the press wheel.
01465
Figure 31
Seeding Depth Control Adjustment
48
997723
Operating Section
Opener Adjustments
Note: Adjusting the opener down pressure does not
change the seeding depth. The seed depth is controlled by
the adjustment on the press wheel. See “Seeding Depth
Control Adjustment” on page 48.
The opener down pressure is adjusted, as shown in Figure
29 on page 47, by changing the notch setting on the top
parallel link. The first notch, number 1, provides the least
down pressure. The rear notch, number 4, provides the
greatest down pressure.
Stop the tractor and raise the Xpress Air Drill until the
openers are off the ground, move the adjustment bolt from
one notch to the other by grasping each end of the bolt and
moving it to the new notch setting.
Initially set all of the openers in the same notch. Lower the
Xpress Air Drill until the 3/4" -1" measurement as shown in
Figure 29 on page 47, is reached on all of the openers.
Next measure the two centre main frame master lift cylinders. Measure from the cylinder head casting to the clevis
on the rod end of the cylinder to determine how many
stroke control segments are needed to hold the Xpress Air
Drill at this height.
mize performance and extend blade and bearing life. If the
pressure is too tight, excessive wear, bearing failure and
plugging may occur. If the pressure is to light, bearing failure and seed trench deterioration may result.
Checking For Loose Pinch
Point
With the openers off the ground, grasp a blade from behind
and rotate it in a forward direction. The pinch point pressure should be adequate enough to rotate both blades
while turning only one. A slight loss of contact during rotation is acceptable. Ideally, you want full contact between
the blades during rotation.
If the blades are loose, shims must be removed from
behind the opener blades to move them closer together. As
blades wear and bearings break in, shims should be
removed. Remove the number of shims necessary to maintain pinch point. Store the shims on the other side of the
bearing under the dust cap.
Checking For Tight Pinch
Point
Place the same number of stroke control segments on the
two master lift cylinders. The outer slave cylinders on the
wings do not require any segments, they will stop when the
master cylinders reach the stroke control segments.
With the openers off the ground, grasp each blade from
behind and rotate them independently in the opposite
direction from each other. The blades should glide against
each other easily without binding.
Openers behind the tire tracks might require additional
down pressure for uniform seed placement. Place the
openers in the tire tracks in a higher setting if more down
pressure is required.
If the blades bind or work against each other while rotating,
shims need to be installed between the opener bar and the
blade to space them apart. When new blades are installed,
shimming is sometimes required. Add the number of shims
necessary to maintain pinch point.
Soil Firming Device Adjustment
The purpose of the firming device is to prevent blowout and
to minimize soil and residue disturbance. For most seeding
conditions, the firming device angle should be set at
approximately 11 1/4" measurement as shown in Figure 29
on page 47. If you are seeding excessively deep or shallow, you may need to change the angle of the firming
device to match your conditions.
Rigid Scraper Adjustment
The rigid scrapers should maintain slight contact with the
inside of the blades for best performance. If adjustment is
required, loosen the two mounting bolts and adjust the
scraper. Tighten the mounting bolts.
Maintaining Proper Pinch
Point
The point at which the two opener blades contact each
other is called the pinch point. The pinch point must be
properly setup with the right amount of pressure to maxi-
997723
49
Operating Section
Adding Or Removing Shims
Note: Each shim is equal to 1/32" at pinch point.
Unfolding And Folding The
Xpress Air Drill
3
1
05964
Figure 32
Pinch Point Adjustment
1.
00206
To add or remove opener shims, as shown in Figure
32, loosen the 3/4" bolt (#1) (the left side has left hand
threads) that mounts the blade to the opener bar. If the
Xpress Air Drill is equipped with soil control devices,
remove the locking arm 3/8" bolt (#2) and the locking
arm (#3) first.
2.
Slowly remove the blade (#4) and bolt (#1) together
being careful not to drop and lose any shims (#5) on
the ground. Remove the 3/4" bolt (#1) and transfer the
shims (#5) from one side to the other, depending on
the adjustment required.
3.
Insert the bolt (#1) through the blade bearing and
place the shims (#5) on the end of the bolt, against the
bearing. Reattach the blades (#4) to the opener bar
with the 3/4" bolt (#1).
4.
2
Tighten the bolts and recheck the pinch point pressure, as described above. Install the soil control
devices, and set the angle while tightening the 3/4"
bolt (#1). Again check the pinch point pressure as
described above. If the pinch point pressure is correct,
attach the locking arm (#3) and the locking arm 3/8"
bolt (#2).
Figure 33
Transport Lock Bar
Note: The folding and unfolding operation of the MORRIS
Xpress Air Drill should be done on smooth terrain.
Unfolding Instructions
1.
The transport bar (#1), as shown in Figure 33, locks
the wing frames in position for transport by a 1" x 6"
transporting pin (Pin has been removed for picture).
When the machine is folded for transport, the pin
should be inserted through the hole (#2). This pin
(shown removed) must be removed to unfold the
Xpress Air Drill. Store the pin in the holder (#3), to prevent loss.
Note: Make sure the bolts that connect the wing braces to
the tongue latch are tight. Periodically check these bolts to
see that they are kept tight.
2.
Make sure the slide hook (#1), as shown in Figure 34,
is lowered to allow automatic locking of tongue latch.
00270
Figure 34
Slide Lock Assembly In Position for Unfolding the Drill
50
997723
Operating Section
3.
Raise the Xpress Air Drill completely.
4.
Lower the air cart’s 2-point lift arms. This allows the
transport bar to clear the lock pin. Now you are ready
to unfold.
5.
Place the tractor in neutral - NOT PARK. This allows
the Xpress Air Drill to pull the tractor backward and forward, allowing the wing lift arm wheels to roll more
easily instead of a sliding motion.
2.
Unlatch the slide hook (#1), as shown in Figure 36, by
rotating it forward in the direction of the arrow to
unlatch the hook.
Note: Always keep your tractor idled down as slow as possible. Be sure the Xpress Air Drill tongue is low enough for
the transporting bar to clear the lock bracket.
6.
Slowly activate the lever on the air cart that controls
the hydraulic fold cylinders. This will allow the Xpress
Air Drill wings to unfold. During this procedure, the
slide lock will slide toward the back of the machine.
After the cylinders are fully extended, move the tractor
ahead until the tongue latch is engaged.
7.
Once the slide lock is locked in position as shown in
Figure 35, the unfolding operation is complete.
05693
Figure 36
Unlatching the Slide Lock Hook
3.
Lower the 2-point arms on the air cart just enough so
that the transport bar will clear the transport locking
pin when the Xpress Air Drill is completely folded.
4.
Slowly activate the lever on the tractor that controls
the hydraulic fold cylinders, and the Xpress Air Drill will
begin to fold. Once the Xpress Air Drill is fully folded,
lift the air cart’s 2-point lift arms. This places the transport bar in a locked position.
5.
Check to see if the transport lock is in the locked position as shown in Figure 37. Using the lever in the tractor that controls the lift cylinders, raise the wing lift
arms (lower the Xpress Air Drill).
05686
Figure 35
Slide Lock Engaged After Unfolding Xpress Air Drill
Folding Instructions
1.
The Xpress Air Drill folds basically the same as it
unfolds. Raise the Xpress Air Drill up with the lever
that controls the hydraulic lift cylinders.
Note: Never fold the Xpress Air Drill while it is in the
ground.
00271
Figure 37
Transport Lock in Locked Position
997723
51
Operating Section
6.
Place the 1" x 6" transport pin, under the transport bar
in hole (#2) as shown in Figure 33 on page 50. The
Xpress Air Drill is now in the transport position.
Note: If the wings will not fold completely in so the transport lock bar will latch as shown in Figure 33 on page 50,
make the necessary adjustments in the following steps.
7.
Loosen the jam nut (#2) as shown in on the inside of
the mount shown in Figure 38. By tightening the nut
(#1) on the outside of the mount, the stroke of the fold
cylinder will lengthen which will bring the wings
together at the front of the Xpress Air Drill. Make equal
adjustments to each side.
06283
Figure 39
Depth Cam Transportation Setting
Lubrication
Your MORRIS Xpress Air Drill is designed to give maximum service life, but a lubrication and maintenance schedule must be followed.
The machine should be thoroughly greased with a multipurpose grease after initial setup and prior to the first field
operation. Greases that may be used are SAE Multipurpose EP grease with 3 to 5 percent molybdenum disulfide
or SAE multipurpose EP grease.
05698
Figure 38
Wing Fold Adjustment Bolts
8.
Small adjustments to the bolts (#3) will bring the wings
in a significant distance. Measure the starting dimension before adjusting the rear nut so the same adjustment can be made to the other side.
Note: Before transporting the drill, adjust the center drill
section depth cam assemblies on the press wheels to the
notch between A & B as shown in Figure 39.
52
997723
Lubricating and regular servicing of the Xpress Air Drill will
insure long life and maximum performance of moving
parts. Wipe dirt from the grease fittings before lubrication. If
a grease fitting is lost, replace it immediately.
The following illustrations in the “Lubrication Section” on
page 31, show the locations of the grease fittings.
Lubrication Section
The following illustrations in
this section show location of
the areas needing lubricated
and the frequency.
997723
53
Lubrication Section
03623
50
Hours
OPTIONAL HYDRAULIC ROW MARKER
Lubrication: Multipurpose Grease
50
Hours
PRESS WHEEL SWIVEL
05965
50
Hours
WING BRACE SWIVEL
05966
50
Hours
2-POINT HITCH
05684
54
997723
Lubrication Section
50
Hours
SHORT WING PIVOTS
05967
50
Hours
CENTRE FRAME PIVOTS
05694
Yearly
WHEEL BEARINGS
(PACK WHEEL BEARINGS)
05695
997723
55
Lubrication Section
Wheel Bearings
The wheel hubs should be cleaned and repacked annually.
This ensures that all contaminants are removed and provides a fresh supply of grease. The following procedure is
necessary in order to properly install the triple lip seal. It is
essential the seal lips are facing away from the hub if the
contaminants are to be kept out.
At The Beginning Of The Next
Planting Season
1.
Clean off any dirt or grease that may have accumulated while the Xpress Air Drill was stored. This will
prevent any abrasive action that could cause excessive wear.
Remove the dust cap, cotter pin, slotted nut and
washer.
2.
Install the rubber seed tubes.
3.
Install all drive chains and lubricate.
2.
Remove the hub and clean the bearings and cavity.
Replace any damaged or worn parts.
4.
Again inspect all nuts and bolts for tightness. Make
sure all moving parts move freely and do not bind.
3.
Pack the hubs with grease.
5.
4.
Install the seal on the spindle shaft. Do not try to place
the hub on the spindle with the seal in the hub.
5.
Replace the hubs with inner bearings in place.
Take the time to read through the manual to refresh
yourself with the safety information and the operating
instructions. This time spent could prevent an injury to
yourself and also prevent damage to the Xpress Air
Drill.
6.
Place the outer bearing, washer and slotted nut on the
wheel spindle.
7.
Adjust the bearings by tightening the slotted nut until
there is a resistance to rotation. Loosen the slotted nut
until the hub can be rotated freely by hand without end
play.
8.
Put the cotter pin through the spindle and slotted nut,
and replace the dust cap
9.
Slide the seal down the spindle, revolving it on the
spindle so the seal lips will be facing away from the
hub.
1.
10. Install the seal in the hub as shown in Figure 39.
Storage
At The End Of The Planting
Season
1.
Clean the Xpress Air Drill thoroughly and inspect all
parts for wear and breakage. Order replacement parts
required now, so needless delays can be avoided at
the beginning of the next planting season.
2.
Remove any seed remaining in the hopper. Any
remaining grain in the seeder units should be removed
by rotating the seeder shaft.
3.
Remove the rubber seed tubes and store inside.
4.
Coat the double disc with oil and grease to prevent
rusting.
5.
Remove all drive chains and clean with diesel fuel. Oil
thoroughly and store in a dust proof and moisture
proof container.
6.
Coat all sprockets with oil or grease to prevent rusting.
56
997723
02139
Figure 39
Installing the Seal in the Hub
Trouble Shooting
Table 1: Trouble Shooting
Symptom
Planting too deep
Probable Cause
Possible Remedy
Press wheel is adjusted too high
Lower the press wheel adjustment, see
“Seeding Depth Adjustment” on
page 48
Excessive down pressure
Decrease the down pressure setting,
see “Opener Adjustments” on page 49
Seed bed is too loose
Use Hydraulic Depth Stops
Xpress Air Drill is not level (Front to
Back)
Adjust 3-point height on the Air Cart
Press wheel is adjusted too low
Raise the press wheel setting, see
“Seeding Depth Adjustment” on
page 48
Insufficient down pressure
Increase the down pressure behind the
tires, see “Opener Adjustments” on
page 49
Press wheel depth is not properly
adjusted
Adjust the press wheels, see “Seeding
Depth Adjustment” on page 48
Seeding shallow behind tractor tires
Increase down pressure behind tractor
tires, see “Opener Adjustments” on
page 49
Seed tubes are sagging
Shorten the seed tubes
Not Maintaining the 3/4” - 1” measurement between the parallel link & the
parallel link stop
Lower the Xpress Air Drill, refer to
“Opener Adjustments” on page 49
Planting too shallow
Uneven seeding depth
Seed is bunching
997723
57
Trouble Shooting
58
997723
Appendix Section
Proper Bolt Use
SAE Fastener Torque
Specifications
When assembling this machine, it is important the proper bolts
are used in each location and that each bolt is torqued correctly. Over torquing a bolt is one of the most frequent causes
of bolt failure. When a bolt is over torqued, the stress on the
bolt exceeds the elastic limit and places the material in a plastic
condition. The bolt will then be permanently lengthened which
lowers the effective tension and clamping force which may
cause it to fail. During assembly, avoid using “cheater bars” as
their use increases the possibility of over torquing a bolt.
SAE Grade Number
The torque specifications below are for UNC and UNF
thread fasteners, plated or unplated, as received from the
supplier. Fasteners can be dry or lubricated with normal
motor oil. Specifications do not apply if graphite, moly-disulfide, or other extreme pressure lubricant is used.
2
5
8*
Bold Head
Identification
(see note)
Foot Pounds Newton Meter Foot Pounds Newton Meter Foot Pounds Newton Meter
Bolt Size Max.
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
1/4”
5
6
7
8
9
11
12
15
12
15
16
20
5/16”
10
12
14
16
17
20.5
23
28
24
29
33
39
3/8”
20
23
27
31
35
42
48
57
45
54
61
73
7/16”
30
35
41
47
54
64
73
87
70
84
95
114
1/2”
45
52
61
70
80
96
109
130
110
132
149
179
9/16”
65
75
88
102
110
132
149
179
160
192
217
260
5/8”
95
105
129
142
150
180
203
244
220
264
298
358
3/4”
150
185
203
251
270
324
366
439
380
456
515
618
7/8”
160
200
217
271
400
480
542
651
600
720
814
976
1”
250
300
339
406
580
696
787
944
900
1080
1220
1464
1-1/8”
800
880
1085
1193
1280
1440
1736
1953
1-1/4”
1120
1240
1519
1681
1820
2000
2468
2712
1-3/8”
1460
1680
1980
2278
2380
2720
3227
3688
1-1/2”
1940
2200
2631
2983
3160
3560
4285
4827
Note: Bolt Head Identification Marks As Per Grade. Manufacturing marks may
vary.
* Thick Nuts Must Be Used With
Grade-8 Bolts.
997723
59
Appendix Section
STANDARD TORQUE SPECIFICATIONS FOR HYDRAULIC TUBES AND FITTINGS
O-Ring Face Seal Fittings (Face Seal End)
Foot Pounds
Tubing O.D.
Newton-Meters
Thread Size
Size
Inches
Millimeters
Min.
Max.
Min.
Max.
4
1/4”
6.4
9/16”-20
10
12
14
16
6
3/8”
9.5
11/16”-16
18
20
24
27
8
1/2”
12.7
13/16”-16
32
35
43
47
10
5/8”
15.9
1”-14
46
50
60
68
12
3/4”
19.1
1-3/16”-12
65
70
90
95
14
7/8”
22.2
1-3/16”-12
65
70
90
95
16
1”
25.4
1-7/16”-12
92
100
125
135
20
1-1/4”
31.8
1-11/16”
125
140
170
190
24
1-1/2”
38.1
2”-12
150
165
200
225
O-RING BOSS PLUGS, ADJUSTABLE
FITTING LOCK NUTS, JIC-37° SEATS
Foot Pounds
Newton Meter
Size
Min.
Max.
Min.
Max.
4
6
10
8
14
5
10
15
14
20
6
15
20
20
27
8
25
30
34
41
10
35
40
47
54
12
60
70
81
95
14
70
80
95
109
16
80
90
108
122
20
95
115
129
156
24
120
140
163
190
1. Lubricate the O-ring
seal with a light coat of
oil or petroleum jelly
and install it into the
groove of the fitting
next to the metal backup washer.
2. Install the fitting until
the metal back-up
washer contacts the
face of the boss. This
locates the maximum
depth of the fitting.
Note: Do not overtighten or distort the
metal back-up washer.
3. Position the fitting by
turning it out (counterclockwise) to a maximum of one complete
revolution and tighten
the locknut to the recommended torque.
Note: In special applications, the fitting will
contact the internal part
of the straight threaded
boss prior to the backup washer.
60
997723
Appendix Section
TIRE INFLATION CHART
Tire Size
Ply/Load Rating
Inflation Pressure (psi) (max.)
16.5 x 6.50 x 8
6 (C)
70 psi
20.5 x 8.00 x 10
4 (E)
90 psi
6.70 x 15
6 (C)
44 psi
7.60 x 15
6 (C)
40 psi
9.5L x 15
8 (D)
44 psi
9.5L x 15
12 (F)
64 psi
11L x 15
8 (D)
36 psi
11L x 15
12 (F)
52 psi
11L x 15 FI*
12 (F)
90 psi
11L x 15
18
76 psi
12.5L x 15
10 (E)
44 psi
12.5L x 15
12 (F)
52 psi
12.5L x 15 FI*
12 (F)
90 psi
12.5L x 15
16
70 psi
12.5 x 15*
20
90 psi
* Use with special Morris heavy duty rim only.
WARNING
Serious injury or death may result from tire failure due to misapplication, improper inflation, overloading or
exceeding the maximum speed.
1.
Follow the tire manufacturer’s instructions.
2.
Check the tire pressure frequently for the proper inflation.
997723
61
Appendix Section
7180 AIR CART
Model
Xpress-30
Xpress-30
Xpress-40
Xpress-40
Spacing
7½”
10”
7½”
10”
Transport Length (overall)
49’6”
49’ 6”
55’ 6”
55’ 6”
Transport Height (overall)
10’9”
10’9”
10’9”
10’9”
Transport Width (overall)
13’10”
13’10”
13’10”
13’10”
Auger
7”x17’
7”x17’
7”x17’
7”x17’
Est. Weight (combined)
21,696
20,223
26,910
24,946
Air Cart
Seeding Unit
5,200
16,496
5,200
15,023
5,200
21,710
5,200
19,746
Tank Capacity
180 bu.
180 bu.
180 bu.
180 bu.
71
109
71
109
71
109
71
109
Front tank
Rear tank
7240 AIR CART
Model
Xpress-30
Xpress-30
Xpress-40
Xpress-40
Spacing
7½”
10”
7½”
10”
Transport Length (overall)
51’ 4”
51’ 4”
57’ 4”
57’ 4”
Transport Height (overall)
10’9”
10’9”
10’9”
10’9”
Transport Width (overall)
13’10”
13’10”
13’10”
13’10”
Auger
7”x20’
7”x20’
7”x20’
7”x20’
Est. Weight (combined)
23,321
21,848
28,535
26,571
Air Cart
Seeding Unit
6,825
16,496
6,825
15,023
6,825
21,710
6,825
19,746
Tank Capacity
240 bu.
240 bu.
240 bu.
240 bu.
95
145
95
145
95
145
95
145
Front tank
Rear tank
62
997723
Parts Section
The drawings and listings in
this section represent all parts
available for order.
997723
63
05943
Frame & Main Frame Assembly
64
997723
Parts Section
Frame & Main Frame Assembly
Seq
Part Number
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
SF9896R
SF2098-1
SF140
SF6477R
SF2096
SFDR80044
SF396
SF397
SF9897R
SF4738
SF6478R
SF3567
SF9261R
SF9909R
SF9895R
SF9271
SF2561
SF1300
SF9900R
SF9268R
SF9915
SF2079
SF1978
SF10313R
SF7001
SF3881
SF2566
SF506
SF2568
SHORT WING, 9433, RIGHT
GREASE ZERK, 1/8" NPTF, 5/8" L
HEX BOLT, 1/2"-13 X 4 1/2", GR 5, Y/D
PIN, 2 1/2" X 14 1/4"
LOCK NUT, 1/2"-13 HEX NYLON INSERT
U-BOLT, 7/8"-9 X 8 3/4" X 7 15/16" W, GR 5, Y/D
LOCK WASHER, 7/8" SPLIT TYPE MED, Y/D
HEX NUT, 7/8"-9 FULL, GR 2, Y/D
SHORT WING, 9433, LEFT
HEX BOLT, 3/8"-16 X 2 3/4", GR 5, Y/D
COLLAR, 3/4"
LOCK NUT, 3/8"-16 HEX NYLON INSERT, GR 2, Y/D
CYLINDER LINK
MAIN FRAME, 9433-30, GRAIN DRILL
MAIN FRAME, FRONT, 9433-40
HEX BOLT, 1 1/8"-7 X 3 1/2" GR5, Y/D
LOCK WASHER, 1 1/8" SPLIT TYPE MED, Y/D
HEX NUT, 1 1/8"-7 FULL, GR 2, Y/D
MAIN FRAME, BACK, 9433-40
TIE PLATE
ADJUSTABLE CYLINDER STOP
JAM NUT, 1 1/2"-6 HEX, GR 2, Y/D
FRAME, DRILL UNIT, 10' @7 1/2"&10"SP(CENTRE ON THE 30’ & 40’ MODELS)
SMV EMBLEM
S.M.V. SOCKET
FLAT WASHER, 1/4", Y/D
HEX BOLT, 1/4"-20 X 3/4", GR 2 Y/D
997723
65
05944
Left Wing Frame Assembly
66
997723
Parts Section
Left Wing Frame Assembly
Seq
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
SF3065
SF9140R
SF669-1
SFDR80044
SFFK150272
SF1283
SF110
SF6757R
SF396
SFDR12031
SF3564
SF9907R
SF6776R
SF397
SF1918
SF10299R
SF9952R
SFFK105044
SF2098-1
SF6785R
SF3164
SF5341
SFFK150157
SF9950R
SF9949R
13
14
15
16
17
18
19
20
21
22
Description
HEX BOLT, 5/8"-11 X 4", GR 5, Y/D
PIN, 2" X 15 3/4" (13 1/4")SQ HEADED
LOCK NUT, 5/8" HEX NYLON INSERT, GR 5, Y/D
U-BOLT, 7/8"-9 X 8 3/4" X 7 15/16" W, GR 5, Y/D
HEX BOLT, 1 1/4"-7 X 10", GR 5, Y/D
LOCK WASHER, 1" SPLIT TYPE MED, Y/D
HEX NUT, 1"-8 FULL, GR 5, Y/D
MOUNTING BRACKET
PIN, 1" X 6" (4 1/4"), Y/D W/ROLL PIN
WIRE LOCK PIN, 3/8" X 1 1/2"
WING BRACE, 9433-30
WING BRACE, 40’
HEX BOLT, 1"-8 X 2 1/2", GR 5 Y/D
WING FRAME, 9030-30 LT, DRILL UNIT
WING FRAME, 9030-40 LT, DRILL UNIT
HEX NUT, 1 1/4"-7, GR 2, Y/D
WING BRACE SWIVEL
ROLL PIN, 5/16" X 2" SPIRAL MEDIUM DUTY, Y/D
PIN, 1 1/4" X 4 5/16" (3 1/4") Y/D
LOCK WASHER, 1 1/4", Y/D
FRAME, DRILL UNIT, 10'@7 1/2"&10"SP (WINGS ON THE 30’ MODEL)
FRAME, DRILL UNIT, 15'@7 1/2"&10"SP(WINGS ON THE 40’ MODEL
997723
67
Parts Section
05945
Right Wing Frame Assembly
68
997723
Parts Section
Right Wing Frame Assembly
Seq
Part Number
1
2
3
4
5
6
7
8
9
10
11
SF1678
SF3938
SF6757R
SFFK150272
SF396
SF397
SFDR80044
SF9140R
SF669-1
SF3065
SF10298R
SF9951R
SF1918
SF3164
SF9907R
SF6776R
SF5341
SF6785R
SF2098-1
SF110
SF1283
SF6506R
SFFK150157
SFFK150144
SF9950R
SF9949R
12
13
14
15
16
17
18
19
20
21
22
23
Description
HEX BOLT, 1"-8 X 4 1/2", GR 5 Y/D
LOCK NUT, 1"-8 HEX NYLON
MOUNTING BRACKET
HEX BOLT, 1 1/4"-7 X 10", GR 5, Y/D
U-BOLT, 7/8"-9 X 8 3/4" X
PIN, 2" X 15 3/4" (13 1/4")SQ HEADED
LOCK NUT, 5/8" HEX NYLON
HEX BOLT, 5/8"-11 X 4", GR 5, Y/D
WING FRAME, 9030-30 RT, DRILL UNIT
WING FRAME, 9030-40 RT, DRILL UNIT
HEX BOLT, 1"-8 X 2 1/2", GR 5 Y/D
WING BRACE, 9433-30
WING BRACE, 40’
PIN, 1 1/4" X 4 5/16" (3 1/4") Y/D
WING BRACE SWIVEL
TRANSPORT BAR
LOCK WASHER, 1 1/4", Y/D
HEX NUT, 1 1/4"-7, GR 2, Y/D
997723
69
Parts Section
05661
2-Point Hitch Assembly
70
997723
Parts Section
2-Point Hitch Assembly
Seq
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
SFFK150261
SF155
SF6470
SF110
SF1283
SF3938
SF9914R
SF1860
SF6817R
SF6818R
SF1978
SF2079
SF2098-1
SF9889R
SF3564
SFB30001
SF3485
Description
HEX BOLT, 1 1/2"-6 X 6" GR 5, Y/D
HEX BOLT, 1"-8 X 3 1/2", GR 5 Y/D
PARKING STAND, 30’ & 40’
HITCH MOUNTING PLATE
PIN, 7/16" X 11/32" DIA, 2" L, KLIK
PIN, 1 7/16" X 10 3/8"
SPACER, 2.500" OD X 1.532" ID, 1" L
TWO POINT HITCH, 2" DIA PIN
WIRE LOCK PIN, 3/8" X 1 1/2"
PIN, 1" X 8 3/8" (6 15/16")
HEX BOLT, 1"-8 X 8", GR 5, Y/D
997723
71
Parts Section
Slide Lock Assembly
05662
72
997723
Parts Section
Slide Lock Assembly
Seq
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
SF2148
SFFK150274
SF9729R
SF9727R
SF6799R
SF6800
SF669-1
SF3164
SFFK150172
SF9731R
SFHEN 3/4-10
SF9730R
SF9728R
SF9732R
SF9733R
SF6779R
SF6782
SF3051
SF2561
SF1300
Description
HEX BOLT, 3/4"-10 X 8 1/2", GR 5, Y/D
HEX BOLT, 5/8"-11 X 11" GR 5, Y/D
SLIDE HOOK
SLIDE LOCK PLATE, RIGHT
SLIDE LOCK ROLLER, 9"
CLAMP BUSHING, 9 1/4"
FLAT WASHER, 1 1/4" SAE, Y/D
SLIDE LOCK ROLLER, 3 7/16"
ROLLER SHAFT, SHORT
SLIDE LOCK PLATE, LEFT
ROLLER SHAFT, LONG
SLIDE LOCK ROLLER, 9"
SLIDE LOCK ROLLER, 6 1/8"
HEX BOLT, 1 1/8"-7 X 5 1/4", GR 5, Y/D
997723
73
Parts Section
Centre Lift Assembly
05663
74
997723
Parts Section
Centre Lift Assembly
Seq
Part Number
1
2
3
4
5
6
7
8
9
SFHEN 3/4-10
SF9894R
SF893
SF9898R
SF1122
SF7325
SF5339
SF3164
SF4430R
SF7419R
Description
centre LIFT,9433-30 & 40 GRAIN DRILL
FLAT WASHER, 3/4" Y/D
BEARING CAP
HEX BOLT, 3/4"-10 X 2 1/2", GR 5, Y/D
BEARING, LIFT (SPLIT) 6" WIDE
PIN, 1" X 4 1/16" (3"), Y/D
CYLINDER, 4" X 10" REPHASING (22 1/4" CPC) CROSS (30’)
CYLINDER, 4 1/2" X 10" REPH (22 1/4" CPC) ORB CROSS (40’)
997723
75
Parts Section
Centre Lift Spindle & Wheel Assembly
05946
76
997723
Parts Section
Centre Lift Spindle & Wheel Assembly
Seq
Part Number
Description
1
2
SF140
SF6555
SF5621
SF113
SF114
SF3066
SF1609
SF3301
SFFK310064
SF3683
SFFK310062
SF3684
SFFK310063
SF3685
SFFK310163
SFFK340167
SFFK340168
SF1605
SF1936
SF1606
SF1935
SF3303
SFFK340165
SF3302
SF1610
SFFK340162
SF3686
SFFK800384
SF3688Y
SF3577
SF5578
SF5555Y
HEX BOLT, 1/2"-13 X 4 1/2", GR 5, Y/D
SPINDLE, 2 3/4" X 14 47/64" L (30’)
SPINDLE, 2 3/4" X 15 5/16"L (40’)
COTTER PIN, 7/32" X 1 1/2" (30’)
COTTER PIN, 3/16" X 1 1/2" (40’)
TRIPLE LIP SEAL (30’)
SEAL, 8-BOLT (40’)
BEARING(LM603049) (30’)
BEARING (JLM506849) (40’)
RACE (LM603011) (30’)
RACE (JLM506810) (40’)
EIGHT BOLT HUB, STUDDED W/CUPS ZERK AND LUG NUTS, PAINTED (30’)
EIGHT BOLT HUB, STUDDED W/CUPS AND LUG NUTS, PAINTED (40’)
LUG BOLT, 5/8"-18 X 2 1/4"
LUG NUT, 5/8"-18, GR 5, 90 DEGTAPER, Y/D
RACE (LM67010) (30’)
RACE (LM501310) (40’)
BEARING (LM67048) (30’)
BEARING (LM501349) (40’)
WASHER, 1 1/32" ID X 1 3/4" ODX 1/8" THICK, PLAIN (30’)
WASHER, 1 1/16" ID X 2 1/8" OD X 1/4" THICK, PLAIN (40’)
HEX NUT, 1"-14 FULL SLOTTED GR 2, PLAIN
DUST CAP, 2.448" OD, Y/D (30’)
DUST CAP, 3.125" OD, Y/D (40’)
8 BOLT HUB ASSEMBLY (30’) (INCLUDES ITEMS 5-16)
EIGHT BOLT HUB ASSY. (40’) (INCLUDES ITEMS 5-16)
WHEEL, 15 X 10, 8 BOLT
VALVE STEM (30’ ONLY)
TIRE, 12.5L X 15, (GY-FI-F) (40’)
TIRE, 12.5L (GY-FI-F) W/15X10 WH ASSY 8 BT (40’)
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
997723
77
Parts Section
Wing Lift Assembly
05947
78
997723
Parts Section
Wing Lift Assembly
Seq
Part Number
1
SF4431R
SF7104R
SF3164
SF5339
SF4623
SF6155
SF2079
SF1978
SF2085
SF9908R
SF6425
SF6301
SF1122
SF1040
SF106
2
3
4
5
6
7
8
9
10
11
12
13
14
Description
CYLINDER, 3 3/4" X 10" REPH. (22 1/4" CPC) CROSS (30’)
CYLINDER, 4 1/4" X 10" REPHAS-ING (22 1/4" CPC) ORB CROSS (40’)
PIN, 1" X 4 1/16" (3"), Y/D
GUIDE PIN
ADJUSTMENT BOLT
LIFT ARM, 9433-30 & 40, GRAIN DRILL
BEARING, LIFT (SPLIT)
BEARING CAP
HEX BOLT, 3/4"-10 X 2 1/2", GR 5, Y/D
997723
79
Parts Section
Wing Lift Spindle & Tire Assembly
01335
80
997723
Parts Section
Wing Lift Spindle & Tire Assembly
Seq
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
SF2585
SF3298
SF302
SF303
SF3066
SF3301
SF1935
SF1936
SF1937
SF3118
SF3117
SF1605
SF1606
SF3303
SF3302
SF1610
SF2098-6
SF3300
SF5094Y
SF3577
SF3579
SF5452Y
Description
HEX BOLT, 7/16"-14 X 3 1/2", GR 5, Y/D
SPINDLE, 2" X 11 1/4"
LOCK WASHER, 7/16" SPLIT TYPE MED, Z
COTTER PIN, 7/32" X 1 1/2"
TRIPLE LIP SEAL
BEARING (LM501349)
RACE (LM501310)
SIX BOLT HUB, STUDDED W/CUPS AND LUG NUTS, PAINTED
LUG BOLT, 9/16"-18 X 1 7/8" PRESS IN, PL
LUG NUT, 9/16"-18, GR 5, 90 DEG TAPER, Y/D
RACE (LM67010)
BEARING (LM67048)
WASHER, 1 1/32" ID X 1 3/4" ODX 1/8" THICK, PLAIN
HEX NUT, 1"-14 FULL SLOTTED GR 2, PLAIN
DUST CAP, 2.448" OD, Y/D
GREASE ZERK, 1/4"-28, 17/32" L
SIX BOLT HUB ASSEMBLY W/3301 SEAL (INCLUDES ITEMS 5-16)
WHEEL, 15 X 6, 6-BOLT
VALVE STEM
TIRE, 9.5L X 15, 12 PLY,
TIRE, 9.5L 12 PLY TUBELESS W/ 15 X 6 WH ASSY 6 BT
997723
81
Parts Section
05670
Main Frame Lift Hydraulics
82
997723
Parts Section
Main Frame Lift Hydraulics
Seq
Part Number
1
2
3
4
5
6
7
SF3253
SF2426
SF5302
SF4198005
SF3984
SF176
SF4130006
SF4198006
Description
HYDRAULIC COUPLER, MALE HALF
MALE CONNECTOR, 7/8"-14 MF X 1/2-14 MPT
PIPE CLAMP, 3/8" BOLT HOLE
HOSE, 1/2" X 198" L, FEMALE ENDS
HEX BOLT, 3/8"-16 X 1 1/4", GR 5, Y/D
HOSE, 1/2" X 130" L, M/F ENDS
WARNING
These parts are important to the safety of this equipment and those who operate it. Use only exact replacement
parts to prevent hydraulic failure. Before replacing these parts, review and follow the instructions in the Safety and
Operating Sections of this manual.
997723
83
Parts Section
Centre Frame Lift Hydraulics
05948
84
997723
Parts Section
Centre Frame Lift Hydraulics
Seq
Part Number
1
2
SF4457
SF4224005
SF4285005
SF4255005
SF4294005
SF4198005
SF4460
SF4065005
SF2355
3
4
5
6
7
Description
90 DEG STRAIGHT THD ELBOW, 7/8"-14 MF X 3/4"-16 MOR
HOSE, 1/2" X 224" L, FEMALE ENDS (30’)
UNION TEE, 7/8"-14 MF
STROKE CONTROL SEGMENTS,1 1/2" DIAMETER
WARNING
997723
85
Parts Section
05949
Outer Wing Lift Hydraulics
86
997723
Parts Section
Outer Wing Lift Hydraulics
Seq
Part Number
1
2
SF4457
SF4224005
SF4285005
SF4255005
SF4294005
SF2587
3
4
Description
90 DEG STRAIGHT THD ELBOW, 7/8"-14 MF X 3/4"-16 MOR
PLASTIC HOSE STRAP, 21 1/2" L
WARNING
997723
87
Parts Section
3 3/4" x 10" Hydraulic Cylinder (4431R)
02135
88
997723
Parts Section
Seq
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
SF8610-1
SF8671-1
SF8899-1
SF8631-1
SF8776-1
SF8736-10
SF8864-1
SF8717-1
SF8683-1
SF8828-1
SF8849-1
SF8698-10
*
*
*
*
*
*
*
SF4458
SF997052
Description
CLEVIS, 1 1/4" THREADS, 1" PIN W/BUSHING, CROSS
CAPSCREW NUT, 5/16" THREADS CROSS
ROD, 1 3/8" DIA, 10" REPHASING CROSS
CAPSCREW, CROSS
SEAL KIT, 3 3/4", 1 3/8" ROD, REPHASING CROSS
HEAD, 3 3/4", 1 3/8" ROD
TIE ROD NUT, 5/8" THREADS
PISTON, 3 3/4" W/1" HOLE
PISTON NUT, 1" CROSS
TUBE, 3 3/4" X 10" REPHASING CROSS
TIE ROD BOLT, 4" X 10" CROSS
BASE, 3 3/4" (ORB), 1" PIN REPHASING CROSS
WIPER
U-CUP
BACKUP
O-RING
O-RING
TEFLON RING
WEAR RING
PLUG, 3/4"-16 MOR
SYSTEMS MUST BE BLED OF AIR
Note: * Available in the Seal Kit Only
997723
89
Parts Section
4" x 10" Hydraulic Cylinder (4430R)
02135
90
997723
Parts Section
Seq
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
SF8610-1
SF8671-1
SF8899-1
SF8631-1
SF8781-1
SF8739-10
SF8864-1
SF8718-1
SF8683-1
SF8826-1
SF8849-1
SF8699-10
*
*
*
*
*
*
*
SF4458
SF997052
Description
CAPSCREW, CROSS
SEAL KIT, 4", 1 3/8" ROD REPHASING CROSS
HEAD, 4" 1 3/8" ROD, REPHASING CROSS
PISTON, 4" W/1" HOLE REPHASING CROSS
TUBE, 4" X 10" REPHASING CROSS
BASE, 4" REPHASING, CROSS
WIPER
U-CUP
BACKUP
O-RING
O-RING
TEFLON RING
WEAR RING
PLUG, 3/4"-16 MOR
997723
91
Parts Section
02136
92
997723
Parts Section
Seq
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
SF8610-1
SF8671-1
SF8966-1
SF8631-1
SF8780-1
SF8741-10
SF8865-1
SF8695-1
SF8683-1
SF8805-1
SF8873-1
SF8675-10
*
*
*
*
*
*
*
SF4458
SF997052
Description
ROD, 1 3/8" DIA, 10" CROSS
CAPSCREW, CROSS
SEAL KIT, 4 1/4", 1 3/8" ROD REPHASING CROSS
HEAD, 4 1/4", 1 3/8" ROD
PISTON, 4 1/4" W/1 1/4" HOLE REPHASING, CROSS
TUBE, 4 1/4" X 10", CROSS
TIE ROD BOLT, 4 1/4" X 10",CROSS
BASE, 4 1/4" (ORB), 1" PIN,CROSS
WIPER
U-CUP
BACK-UP
O-RING
O-RING
TEFLON RING
WEAR RING
PLUG, 3/4"-16 MOR
997723
93
Parts Section
02136
94
997723
Parts Section
Seq
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
SF8617-1
SF8671-1
SF8901-1
SF8631-1
SF8799-1
SF8730-10
SF8865-1
SF8720-1
SF8685-1
SF8804-1
SF8873-1
SF8679-10
*
*
*
*
*
*
*
SF4458
SF997052
Description
CLEVIS, 1 1/2" THREADS, CROSS
CAPSCREW, CROSS
SEAL KIT, 4 1/2", 1 1/2" ROD, CROSS
HEAD, 4 1/2", 1 1/2" ROD
PISTON, 4 1/2" REPHASING CROSS
PISTON NUT, 1 1/4" THREAD, CROSS
TUBE, 4 1/2" X 10" REPHASING CROSS
TIE ROD BOLT, 4 1/4" X 10",CROSS
BASE, 4 1/2" (ORB), 1" PIN CROSS
WIPER
U-CUP
BACKUP
O-RING
O-RING
TEFLON RING
WEAR RING
PLUG, 3/4"-16 MOR
997723
95
Parts Section
Transport Lock Assembly
05667
96
997723
Parts Section
Transport Lock Assembly
Seq
Part Number
1
2
3
4
5
6
7
SF7198
SF7197
SF7771
SF3881
SF9901R
SFFK150025
SF7193R
Description
SPRING, 1.250" OD X 1.020" ID, 6" L EXTENSION
CABLE, 17"
HEX BOLT, 1/4"-20 X 4 1/2", GR 5, Y/D
TRANSPORT LOCK, 9433
ROLL PIN, 1/2" X 3 1/2" Y/D
PIN, 1 1/2" X 18" (16")
997723
97
Parts Section
Main Frame Fold Hydraulics
05671
98
997723
Parts Section
Main Frame Fold Hydraulics
Seq
Part Number
1
2
3
4
5
6
SF3253
SF2425
SF5302
SF4200002
SF2487
SF4118003
SF4191003
Description
HEX BOLT, 3/8"-16 X 2 1/2", GR 5, Y/D
WARNING
997723
99
Parts Section
05950
Centre Frame Fold Hydraulics
100
997723
Parts Section
Centre Frame Fold Hydraulics
Seq
Part Number
1
2
3
4
5
6
7
8
9
SF4466
SF9725R
SF4072002
SF4200002
SFFK150172
SF3164
SF9910
SF4060002
SF2429
Description
90 DEG STR THD ELBOW, 3/4"-16 MF
CYLINDER, 4" X 16" W/8618-1 CLEVIS
FLAT WASHER, 1 1/4" SAE, Y/D
PIN, 1 1/4" X 6 3/8"
WARNING
997723
101
Parts Section
05519
102
997723
Parts Section
Seq
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
SF8618-1
SF8671-1
SF8877-1
SF8631-1
SF8789-1
SF8744-10
SF8864-1
SF8713-1
SF8681-1
SF8833-1
SF8854-1
SF8692-10
*
*
*
*
SF4458
SF997309
Description
CLEVIS, 1 1/4" THREADS, 1 1/4" PIN W/BUSHING, CROSS
CAPSCREW, CROSS
SEAL KIT, 4", 1 1/2" ROD REPHASING CROSS
HEAD, 4", 1 1/2" ROD, CROSS (ORB)
PISTON, 4" W/1" HOLE CROSS
PISTON NUT, 3/4" CROSS
TUBE, 4" X 16" CROSS
BASE, 4" (ORB), 1 1/4" PIN CROSS
WIPER
U-CUP
BACKUP
O-RING
PLUG, 3/4"-16 MOR
HYDRAULIC SYSTEM HAZARD
997723
103
Parts Section
All Purpose Heads Up Opener
05951
104
997723
Parts Section
All Purpose Heads Up Opener
Seq
Part Number
Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
SF7024
SFFK150283
SF669-1
SF9683
SF2096
SF6618
SF6619
SFN11470
SF10157B
SF9937B
SF7033B
SF7032B
SF7084
SF9680
SF9102
SF7034B
SF7085
SF7040
SF7083
SF6440
SF10333B
SF3881
SF1193
SF7042
SF3567
SF7041B
SF1021
SF7043
SF5934
SF2098-1
SF9101B
SF2487
SFHEN 3/4-10
SF9682
SF7034
SF9708
SF3806
SF7029
SF5935
SFDR10013
SF3723
SF6377
SF10127B
SF10126B
SF9780B
SFDR80011
SFB1127
SF6378
SF7205
SF7203
SFDR81044
SF7201
SF6376
SF7859
SF9753
SF7204
SF1220
SF7031B
SF840
SF7030
SF7028B
SF7027B
SF7026B
SF317
SF7266
SF9879B
SF9880B
L-BOLT, 5/8"-11 X 4 5/8" X 6 5/8", Y/D
FLAT WASHER, 5/8" SAE, Y/D
1/2-13 FLANGE TOPLOCK NUT GR G CAD/ WAX
WASHER,.531"ID X .813"OD,.129" CROWN HEIGHT, CURVED SPRING
WASHER, .531" ID X 2.000" OD X .058" THICK, Y/D
HOSE CLAMP
BRACKET, HOSE HOLDER
SEED TUBE, ALL PURPOSE HEADS UP
SPACER TUBE, 4 1/2" L,
PARALLEL LINKAGE, 11" TOP, ALL PURPOSE
DEPTH LOCK PIN, Y/D
HHFS 1/2"-13 X 6 1/2" GR5 Y/D
DEPTH CAM ASSY, ALL PURPOSE
OPENER FRAME, ALL PURPOSE
SPACER, DEPTH LOCK, Y/D
DEPTH LOCK, ALL PURPOSE, Y/D
SPRING, .500" OD X .375" ID, 1 1/2" L EXTENSION
ROLL PIN, 1/4" X 1 3/4" MEDIUM DUTY, Y/D
PRESS WHEEL FRAME SWIVEL, W/SPRING,
HEX BOLT, 3/8"-16 X 3/4",GR 5, Y/D
CLAMP BUSHING,.750" OD X .532" ID, .109 W, 2 5/64" L
PRESS WHEEL FRAME, SWIVEL, ALL PURPOSE
HEX BOLT, 3/4"-10 X 5 1/2", GR 5, Y/D
CLAMP BUSHING, 1" OD X .760"ID,.120" W, 3 5/8" L
BUSHING, 1 1/4" OD X 1" ID, 5/8" L (HARD) SPRING
PRESS WHEEL FRAME, REAR, ALL PURPOSE
HEX BOLT, 3/8"-16 X 2 1/2", GR 5, Y/D
HHFS 1/2"-13 X 3 3/4" GR5 Y/D
BUSHING, DEPTH CONTROL, 1/2"
SPRING, .162" WIRE DIA X 5" L EXTENS
HEX BOLT, 3/8"-16 X 3", GR 5, Y/D
BUSHING, 1" OD X 3/4" ID, 5/8" L (HARD) SPRING
HEX BOLT, 5/16"-18 X 3/4" GR 5 Y/D
LOCK WASHER, 5/16" SPLIT TYPE, MED, Y/D
SCRAPER, OPENER LEFT
SCRAPER, OPENER RIGHT
OPENER BAR, ALL PURPOSE, HEADS UP
WASHER, MACHINE
DUST CAP
MOUNTING BRACKET, SOIL CONTROL DEVIC
LOCKING ARM
HEX BOLT, 3/4"-10 LH X 2", GR 5, Y/D
SOIL CONTROL STRIP
CARRIAGE BOLT, 5/16"-18 X 1" GR 5, Y/D
SUPPORT, SOIL CONTROL STRIP
OPENER BLADE & BRG ASSEMBLY, HEADS UP
MOUNTING BRACKET, SOIL CONTROL DEVIC
HEX BOLT, 3/4"-10 X 2", GR 5 Y/D
PARALLEL LINKAGE, 11" LOWER, ALL PURPOSE
HEX BOLT, 1/2"-13 X 5 1/2", GR 5, Y/D
SPRING ANCHOR, ALL PURPOSE
OPENER MOUNT, LONG, ALL
OPENER MOUNT, SHORT, ALL
SPRING, 1.6875" OD X 1.1635" ID, 7 5/16" L, EXTENSION BLACK
SOIL CONTROL DEVICE ASSY
ALL PURPOSE OPENER ASSEMBLY, HEADS UP, SHORT(ALL ABOVE PARTS BUT 8-9)
ALL PURPOSE OPENER ASSEMBLY, HEADS UP, LONG(ALL ABOVE PARTS BUT 8-9)
62
63
997723
105
Parts Section
05952
All Purpose Heads Up Opener Press Wheel Assembly
106
997723
Parts Section
All Purpose Heads Up Opener Press Wheel Assembly
Seq
Part Number
1
2
3
4
5
6
7
8
SF2557
SF6869
SF7375
SF6866
SF6868
SF6867
SF7218
SF669-1
Description
HEX BOLT, 5/8"-11 X 4 1/2", GR 5, Y/D
PRESS WHEEL ASSY, 4" X 12" DOUBLE RIB NYLON RIM
PRESS WHEEL ASSY, 3" X 13" DOUBLE RIB STEEL RIM
PRESS WHEEL ASSY, 3" X 13" centre RIB STEEL RIM
PRESS WHEEL ASSY, 2" X 13" V-CROWN STEEL RIM
PRESS WHEEL ASSY, 2" X 13" SMOOTH CROWN STEEL RIM
BEARING, 40MM
997723
107
Parts Section
Press Wheel & Tire Assembly
05012
108
997723
Parts Section
Press Wheel & Tire Assembly
Seq
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
SF7416
SF9109
SF7218
SF3881
SF2487
SF7415
SF7412
SF7413
SF175
SF7411
SF7409
SF7410
SF7408
Description
HEX BOLT, 1/4"-20 X 2", GR 5, Y/D
RIM, 4" X 12" NYLON HALF F/40 MM BRG
BEARING, 40MM
HEX BOLT, 3/8"-16 X 2 1/2", GR 5, Y/D
HEX BOLT, 3/8"-16 X 1 3/8" GR 5, Y/D
RIM, 3" X 13" 13 GA CLINCHER HALF
RIM, 2" X 13" 13 GA CLINCHER HALF FOR 40MM
HEX BOLT, 3/8"-16 X 1 1/2", GR 5, Y/D
TIRE, 2" X 13" SMOOTH CROWN CLINCHER
TIRE, 2" X 13" V-CROWN
TIRE, 3" X 13" centre RIB
TIRE, 4" X 12" DOUBLE RIB
997723
109
Parts Section
05953
110
997723
Parts Section
Seq
Part Number
1
2
SF6682
SF7223B
SF7224B
SF7221B
SF3567
SF178
SF7222B
CARRIAGE BOLT, 3/8"-16 X
OPENER SHIELD, 5' (30’ & 40’ DRILL)
OPENER SHIELD, 7.5' (40’ DRILL)
MOUNTING CLIP
HEX BOLT, 3/8"-16 X 1", GR 5, Y/D
TIE STRAP
SF7229B
SF7230B
OPENER SHIELD ASSY, 30' DRILL
OPENER SHIELD ASSY, 40' DRILL
3
4
5
6
Description
997723
111
Parts Section
Row Marker Assembly
02820
112
997723
Parts Section
Row Marker Assembly
Seq
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
SF7779
SF7778
SF1609
SF776
SF777
SF7780B
SF7775
SF3567
SF7781B
SF7773
SF112
SF7825
SF114
SF113
SF486
SF2487
SF7782R
SF1507
SFB2632
SF2045
SF159
SF6646R
SF6815R
SF2096
SF2098-1
SF7755R
SF7667R
SF7445
SF7446
SF3938
SF7752R
SF7753R
SF175
SF7754
SF2316
SFHEN 3/4-10
SF7748R
SF7749R
SF7750R
SF7751R
SF6652
SF2098-6
SF2045
SF3303
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
Description
DUST CAP, 1.986" OD X .032" TH Y/D
HEX NUT, 1"-14 SLOTTED .531" TH GR 2, PLAIN
COTTER PIN, 3/16" X 1 1/2"
BEARING (L44643)
RACE (L44610)
FOUR BOLT HUB W/CUPS & ZERK
SEAL, SINGLE LIP (SL-123)
MARKER ARM DEPTH BAND
14" BLADE, 4 BOLT, .138" THICK .78" CONCAVITY
HEX BOLT, 1/2"-13 X 2 1/2", GR 5, Y/D
SPINDLE, 1 1/4" X 8 5/8"(1"-14 UNS THD)
HEX BOLT, 3/8"-16 X 2 1/2", GR 5, Y/D
HUB BRACKET
HEX BOLT, 1/2"-13 X 3 1/2", GR 5, Y/D
EXTENSION ARM, 48"L
HEX BOLT, 1/2"-13 X 1 3/4", GR5, Y/D
JAM NUT, 1/2"-13, GR 2, Y/D
MARKER ARM, 30’ OUTER
MARKER ARM, 40’ OUTER
MARKER LINKAGE ARM, OUTER
SPACER, .750"OD X .532"ID, 3/8"L
CHAIN, 5/16" PROOF, 78 3/4" L
CHAIN, 5/16" PROOF, 109 1/8" L
MARKER PIVOT HEAD, RIGHT
MARKER PIVOT HEAD, LEFT
HEX BOLT, 3/8"-16 X 1 1/2", GR 5, Y/D
CARRIAGE BOLT, 3/4"-10 X 6", GR 5, Y/D
HEX BOLT, 1"-8 X 8 1/2", GR 5, Y/D
LOCK NUT, 3/4" HEX NYLON INSERT, GR 5, Y/D
MARKER ARM, 30’ INNER RIGHT
MARKER ARM, 30’ INNER LEFT
MARKER ARM, 40’ INNER RIGHT
MARKER ARM, 40’ INNER LEFT
BUSHING, 1.500" OD X 1.156" ID 11 7/16" L
GREASE ZERK, 1/4"-28, 17/32" L
HEX BOLT, 1/2"-13 X 1 3/4", GR5, Y/D
WASHER, 1 1/32" ID X 1 3/4" ODX 1/8" THICK, PLAIN
997723
113
Parts Section
Row Marker Mount Assembly
05954
114
997723
Parts Section
Row Marker Mount Assembly
Seq
Part Number
1
2
3
4
5
6
SF2096
SF3758
SF330
SF7450R
SF6651R
SF6649R
SF5934
SF7448R
SF893
SF5339
SF112
SF669-1
SF106
SF1040
SF6656R
SF7449R
SF5201
SF6676R
SF5502
SF3164
SF6633R
SF1122
SF6643
SF5230
SF7772R
SF2561
SF1300
SF7789
SFDR80019
SF7451R
SF7452R
SF1243
SF7788R
SF6282
SFDR10524
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
Description
HEX BOLT, 5/8"-11 X 3", GR 5, Y/D
HEX BOLT, 1/2"-13 X 2" GR 5, Y/D
MARKER LINKAGE ARM, 12" L
FOLD LINK, 30’ & 40’ MARKER
MARKER LINKAGE, CURVED
BUSHING, 1 1/4" OD X 1" ID, 5/8" L (HARD) SPRING
MARKER LINKAGE ARM, 50 3/8" L
PIN, 1" X 4 1/16" (3"), Y/D
HEX BOLT, 1/2"-13 X 2 1/2", GR 5, Y/D
MARKER LINKAGE MOUNT
BUSHING, CLAMP
BALL LOCK PIN, 3/8" X 3"
CYLINDER STOP, MARKER
PIN, 1" X 5 1/16" (4") Y/D
CYLINDER, 3" X 20" (30 1/4" CPC) ORB
HEX BOLT, 3/4"-10 X 2 1/2", GR 5, Y/D
PIN, 1" X 8" (6 11/16"), Y/D
HEX BOLT, 1 1/8"-7 X 14 1/2", Y/D
MARKER MOUNT, 30’ & 40’
HEX BOLT, 3/4"-10 X 4" FULL THD, GR 5, Y/D
U-BOLT, 3/4"-10 X 8 3/4" X 7 13/16" W, GR 5, Y/D
MARKER CHAIN PIVOT, RIGHT
MARKER CHAIN PIVOT, LEFT
JAM NUT, 3/4"-10 HEX, GR 2, Y/D
CLEVIS
HEX BOLT, 7/16"-14 X 3", GR 5, Y/D
LOCK NUT, 7/16"-14 HEX NYLON INSERT, Y/D
997723
115
Parts Section
Row Marker Hydraulics on Main Frame
05673
116
997723
Parts Section
Row Marker Hydraulics on Main Frame
Seq
Part Number
1
2
3
4
5
6
SF3253
SF6177
SF5302
SF4200011
SF2487
SF4112012
SF4185012
SF4234011
7
Description
HOSE, 1/4" X 200" L, 9/16"-18 F/ENDS (30’ & 40’)
HEX BOLT, 3/8"-16 X 2 1/2", GR 5, Y/D
HOSE, 1/4" X 112"L,9/16"-18 M/F ENDS
HOSE, 1/4" X 185"L,9/16"-18 M/F ENDS
HOSE, 1/4" X 234" L, 9/16"-18 F/ENDS (30’ & 40’)
WARNING
997723
117
Parts Section
05955
118
997723
Parts Section
Seq
Part Number
1
2
SF6935
SF4200011
SF4263011
SF4178011
SF4240011
SF4200011
SFB1141
SF474
SF4234011
SF7077
SF3567
SFDR56006
SF317
SF178
3
4
5
6
7
8
9
10
11
12
Description
90 DEG STR THD ELBOW, 9/16"-18 MF X 3/4"-16 MOR
HOSE, 1/4" X 200" L, 9/16"-18 F/ENDS (30’)
HOSE, 1/4" X 263" L, 9/16"-18 F/ENDS (40’)
HOSE, 1/4" X 178" L, 9/16"-18 F/ENDS (30’)
HOSE, 1/4" X 240" L, 9/16"-18 F/ENDS (40’)
HOSE, 1/4" X 200" L, 9/16"-18 F/ENDS (30’ & 40’)
VALVE MOUNT
HEX BOLT, 3/8"-16 X 2", GR 5 Y/D
HOSE, 1/4" X 234" L, 9/16"-18 F/ENDS
VALVE, 3/4-16 OR SEQUENCE
HEX BOLT, 3/8"-16 X 1", GR 5, Y/D
WARNING
997723
119
Parts Section
Wing Frame Row Marker Hydraulics
05956
120
997723
Parts Section
Wing Frame Row Marker Hydraulics
Seq
Part Number
1
2
SF6935
SF4200011
SF4263011
SF4178011
SF4240011
SF2487
SF176
SF5302
3
4
5
6
Description
90 DEG STR THD ELBOW, 9/16"-18 MF X 3/4"-16 MOR
HOSE, 1/4" X 200" L, 9/16"-18 F/ENDS (30’)
HOSE, 1/4" X 263" L, 9/16"-18 F/ENDS (40’)
HOSE, 1/4" X 178" L, 9/16"-18 F/ENDS (30’)
HOSE, 1/4" X 240" L, 9/16"-18 F/ENDS (40’)
HEX BOLT, 3/8"-16 X 2 1/2", GR 5, Y/D
WARNING
997723
121
Parts Section
02119
122
997723
Parts Section
Seq
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
SF8610-1
SF8671-1
SF8878-1
SF8631-1
SF8762-1
SF8722-10
SF8866-1
SF8711-1
SF8681-1
SF8806-1
SF8872-1
SF8701-10
*
*
*
*
*
SF4458
Description
CAPSCREW, CROSS
SEAL KIT, 3", 1 1/4" ROD, CROSS
HEAD, 3", 1 1/4" ROD, CROSS (ORB)
TIE ROD NUT, 1/2"-13 UNC CROSS
PISTON, 3" W/3/4" HOLE CROSS
PISTON NUT, 3/4" CROSS
TUBE, 3" X 20" CROSS
TIE ROD BOLT, 3" X 20", CROSS
BASE, 3" (ORB) CROSS
WIPER
U-CUP
BACKUP
O-RING
TEFLON RING
PLUG, 3/4"-16 MOR
997723
123
Parts Section
Light Kit Assembly
06054
124
997723
Parts Section
Light Kit Assembly
Seq
Part Number
1
SF10329
2
3
SF2587
SF10330
4
5
6
SF10007
SF10008
SF10314R
SF10315R
SF9965
SF893
SF106
SF1220
7
8
9
10
Description
HARNESS, 38’ WISHBONE, EQUAL LEGS,SHIELDED FESTOON CABLE W/
CONNECTORS
PLASTIC HOSE STRAP, 21 1/2" L
HARNESS, 54" AMBER LEG - 40" RED LEG WISHBONE, W/FLAT &
TRIANGULAR CONNECTORS
LAMP, SINGLE AMBER FRT/REAR
LAMP, SINGLE RED REAR / BLANK FRT
BRACKET, LIGHT
BRACKET, LIGHT
SCREW, HEX HEAD, 1/4"-14 X 3/4" TYPE AB, Y/D
HEX BOLT, 3/4"-10 X 2", GR 5 Y/D
997723
125
Parts Section
06151
Decal Placement
126
997723
Parts Section
Decal Placement
Seq
Part Number
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
SF997661
SF997662
SF997043
SF997408
SF997313
SF997322
SF997318
SF997323
SF997052
SF997311
SF997324
SF997246
SF997459
SFN34094
SFC-3902
SF997711
SF997663
Description
TAPE, RED REFLECTIVE 2" X 9" L
TAPE, ORANGE REFLECTIVE 2" X 9" L
READ OPERATORS MANUAL
TRANSPORTING HAZARD
CAUTION - INSTALL LOCK PINS BEFORE TRANSPORTING
DANGER - FRAME PINCH POINT
WARNING - 20 MPH MAX TRANSPORT SPEED
DANGER - ELECTROCUTION HAZARD
HIGH PRESSURE FLUID HAZARD
DANGER - OVERHEAD MARKER HAZARD
FEMA DECAL
PATENT DECAL, #5,626,196
EXPRESS DECAL
MORRIS DECAL
DECAL, MANUFACTURED BY SUNFLOWER MFG
TAPE, YELLOW REFLECTIVE 2" X 9" L
997723
127
Parts Section
128
997723
Numerical Part Number Index
Symbols
*
89, 91, 93, 95, 103, 123
S
SF10007
125
SF10008
125
105
SF10126B
105
SF10127B
SF10157B
105
105
SF1021
69
SF10298R
SF10299R
67
65
SF10313R
125
SF10314R
SF10315R
125
125
SF10329
125
SF10330
SF10333B
105
79, 115
SF1040
79, 115, 125
SF106
SF110
67, 69, 71
113, 115
SF112
75, 79, 115
SF1122
SF113
77, 113
77, 113
SF114
105
SF1193
SF1220
105, 125
115
SF1243
67, 69, 71
SF1283
SF1300
65, 73, 115
65, 77
SF140
113
SF1507
SF155
71
113
SF159
77, 81
SF1605
SF1606
77, 81
77, 113
SF1609
77, 81
SF1610
SF1678
69
109, 113
SF175
83, 121
SF176
SF178
111, 119
71
SF1860
67, 69
SF1918
SF1935
77, 81
77, 81
SF1936
81
SF1937
65, 71, 79
SF1978
SF2045
113
65, 71, 79
SF2079
79
SF2085
SF2096
65, 105, 113, 115
SF2098-1 65, 67, 69, 71, 105, 113
SF2098-6
81, 113
SF2148
73
113
SF2316
85
SF2355
SF2425
99
83
SF2426
101
SF2429
SF2487 99, 105, 109, 113, 117, 121
107
SF2557
65, 73, 115
SF2561
SF2585
81
87, 125
SF2587
81
SF302
SF303
81
73
SF3051
67, 69
SF3065
SF3066
77, 81
81
SF3117
81
SF3118
SF3164 67, 69, 73, 75, 79, 101, 115
105, 119
SF317
83, 99, 117
SF3253
SF3298
81
115
SF330
81
SF3300
SF3301
77, 81
77, 81
SF3302
77, 81, 113
SF3303
SF3485
71
67, 71
SF3564
65, 105, 111, 113, 119
SF3567
SF3577
77, 81
81
SF3579
77
SF3683
SF3684
77
77
SF3685
77
SF3686
SF3688Y
77
105
SF3723
115
SF3758
SF3806
105
97, 105, 109
SF3881
69, 71, 113
SF3938
SF396
65, 67, 69
65, 67, 69
SF397
83
SF3984
101
SF4060002
SF4065005
85
101
SF4072002
117
SF4112012
SF4118003
99
83
SF4130006
119, 121
SF4178011
117
SF4185012
SF4191003
99
83, 85
SF4198005
83
SF4198006
SF4200002
99, 101
117, 119, 121
SF4200011
85, 87
SF4224005
SF4234011
117, 119
119, 121
SF4240011
85, 87
SF4255005
SF4263011
119, 121
85, 87
SF4285005
85, 87
SF4294005
SF4430R
75
79
SF4431R
85, 87
SF4457
SF4458 89, 91, 93, 95, 103, 123
85
SF4460
101
SF4466
SF4623
79
65
SF4738
119
SF474
SF486
113
81
SF5094Y
115
SF5201
SF5230
115
83, 99, 117, 121
SF5302
75, 79, 115
SF5339
SF5341
67, 69
81
SF5452Y
115
SF5502
SF5555Y
77
77
SF5578
77
SF5621
SF5934
105, 115
105
SF5935
79
SF6155
SF6177
117
115
SF6282
79
SF6301
SF6376
105
105
SF6377
105
SF6378
SF6425
79
105
SF6440
71
SF6470
65
SF6477R
SF6478R
65
69
SF6506R
77
SF6555
SF6618
105
105
SF6619
115
SF6633R
997723
129
115
SF6643
SF6646R
113
115
SF6649R
115
SF6651R
SF6652
113
115
SF6656R
115
SF6676R
SF6682
111
SF669-1 67, 69, 73, 105, 107, 115
67, 69
SF6757R
67, 69
SF6776R
SF6779R
73
73
SF6782
67, 69
SF6785R
SF6799R
73
73
SF6800
113
SF6815R
SF6817R
71
71
SF6818R
107
SF6866
SF6867
107
107
SF6868
107
SF6869
SF6935
119, 121
105
SF7024
105
SF7026B
SF7027B
105
105
SF7028B
105
SF7029
SF7030
105
105
SF7031B
105
SF7032B
SF7033B
105
105
SF7034
105
SF7034B
SF7040
105
105
SF7041B
105
SF7042
SF7043
105
119
SF7077
105
SF7083
SF7084
105
105
SF7085
79
SF7104R
SF7193R
97
97
SF7197
97
SF7198
SF7201
105
105
SF7203
105
SF7204
SF7205
105
107, 109
SF7218
111
SF7221B
SF7222B
111
111
SF7223B
111
SF7224B
SF7229B
111
111
SF7230B
105
SF7266
SF7325
75
130
SF7375
107
SF7408
109
109
SF7409
109
SF7410
SF7411
109
109
SF7412
109
SF7413
SF7415
109
109
SF7416
75
SF7419R
113
SF7445
SF7446
113
115
SF7448R
115
SF7449R
SF7450R
115
115
SF7451R
115
SF7452R
SF7667R
113
113
SF7748R
113
SF7749R
SF7750R
113
113
SF7751R
113
SF7752R
SF7753R
113
113
SF7754
113
SF7755R
SF776
113
113
SF777
97
SF7771
SF7772R
115
113
SF7773
113
SF7775
SF7778
113
113
SF7779
113
SF7780B
SF7781B
113
113
SF7782R
115
SF7788R
SF7789
115
113
SF7825
105
SF7859
SF840
105
89, 91, 93, 123
SF8610-1
95
SF8617-1
SF8618-1
103
SF8631-1 89, 91, 93, 95, 103, 123
SF8671-1 89, 91, 93, 95, 103, 123
SF8675-10
93
95
SF8679-10
103, 123
SF8681-1
SF8683-1
89, 91, 93
95
SF8685-1
103
SF8692-10
SF8695-1
93
89
SF8698-10
91
SF8699-10
SF8701-10
123
123
SF8711-1
103
SF8713-1
SF8717-1
89
997723
SF8718-1
SF8720-1
SF8722-10
SF8730-10
SF8736-10
SF8739-10
SF8741-10
SF8744-10
SF8762-1
SF8776-1
SF8780-1
SF8781-1
SF8789-1
SF8799-1
SF8804-1
SF8805-1
SF8806-1
SF8826-1
SF8828-1
SF8833-1
SF8849-1
SF8854-1
SF8864-1
SF8865-1
SF8866-1
SF8872-1
SF8873-1
SF8877-1
SF8878-1
SF8899-1
SF8901-1
SF893
SF8966-1
SF9101B
SF9102
SF9109
SF9140R
SF9261R
SF9268R
SF9271
SF9680
SF9682
SF9683
SF9708
SF9725R
SF9727R
SF9728R
SF9729R
SF9730R
SF9731R
SF9732R
SF9733R
SF9753
SF9780B
SF9879B
SF9880B
SF9889R
SF9894R
SF9895R
SF9896R
91
95
123
95
89
91
93
103
123
89
93
91
103
95
95
93
123
91
89
103
89, 91
103
89, 91, 103
93, 95
123
123
93, 95
103
123
89, 91
95
75, 115, 125
93
105
105
109
67, 69
65
65
65
105
105
105
105
101
73
73
73
73
73
73
73
105
105
105
105
71
75
65
65
SF9897R
SF9898R
SF9900R
SF9901R
SF9907R
SF9908R
SF9909R
SF9910
SF9914R
SF9915
SF9937B
SF9949R
SF9950R
SF9951R
SF9952R
SF9965
SF997043
SF997052
SF997246
SF997309
SF997311
SF997313
SF997318
SF997322
SF997323
SF997324
SF997408
SF997459
SF997661
SF997662
SF997663
SF997711
SFB1127
SFB1141
SFB2632
SFB30001
SFC-3902
SFDR10013
SFDR10524
SFDR12031
SFDR56006
SFDR80011
SFDR80019
SFDR80044
SFDR81044
SFFK105044
SFFK150025
SFFK150144
SFFK150157
SFFK150172
SFFK150261
SFFK150272
SFFK150274
SFFK150283
SFFK310062
SFFK310063
SFFK310064
SFFK310163
SFFK340162
SFFK340165
65
75
65
97
67, 69
79
65
101
71
65
105
67, 69
67, 69
69
67
125
127
89, 91, 93, 95, 127
127
103
127
127
127
127
127
127
127
127
127
127
127
127
105
119
113
71
127
105
115
67
119
105
115
65, 67, 69
105
67
97
69
67, 69
73, 101
71
67, 69
73
105
77
77
77
77
77
77
SFFK340167
SFFK340168
SFFK800384
SFHEN 3/4-10
SFN11470
SFN34094
77
77
77
73, 75, 105, 113
105
127
997723
131
132
997723

Drill Unit Operator`s Manual

Transcription

Similar documents

Ferrari Carb Mod

Quarterback Development Drills

frank meeink - Admire Entertainment

scan drill kb

August 16 Sale Bill

Custom Mount for JC Whitney Large Trunk Concours

DJ Salif Keita African Dance event for National French Week

July 2008 - TEAM Security

Assembly Guide MultipliCITY is an international

Bolt Messenger