Manual

Transcription

Manual - Mindprint

E S PAGñOL
1.0
F R ANÇAI S
DE UTSC H
ENGLISH
www.mindprint.com
15.10.2003
9:15 Uhr
MANUAL
ITAL IAN O
EnVoice_Manual_1.1
Seite 1
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 2
MindPrint ® EN-VOICE ® MK II
Important:
Please read safety instructions
on page 68 before use!
Wichtig:
Bitte lesen Sie vor der Inbetriebnahme
die Sicherheitshinweise auf Seite 69!
Important :
Avant la mise en service, prière de lire
les consignes de sécurité à la page 69 !
Importante:
Prima di utilizzare lo strumento, leggere
attentamente gli avvisi di sicurezza su pagina 70!
Importante:
¡Antes de la puesta en servicio lea por favor
las indicaciones de seguridaden la página 70!
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 3
In November 1998, a dream harbored by many musicians became reality with the EN-VOICE®
- goodbye demo quality sound, hello professional sounding recordings, achievable and affordable by all. When we set out to develop the EN-VOICE®, we did so with a lofty goal in mind
– to build a better product offering superior sound quality and affording greater ease of use.
And because better products are the product of inspiration and innovation rather than imitation, we aspired to create an original. The EN-VOICE® was that original, an entirely new breed
of device that would make the outboard channel strip a mainstay of home recording.
Often copied yet never matched, this workhorse recording preamp delivers the sonic
goods in thousands of studios all over the world.
After five years of trusty service, it is time our original was adapted to the working habits and
requirements of a rapidly evolving recording market. In the age of the laptop, the modern
producer’s top priorities are - alongside awesome sound - flexibility, mobility and a desktopenabled design. Today we’re still aiming for enhanced sound quality and greater ease of use
in our quest to build a better product. Likewise, today we’re still striving for greater flexibility,
mobility, and safety. Enter the EN-VOICE® MK II - another original with features that the world
has never seen in a tube-powered channel strip.
WARRANTY
Register your EN-VOICE® MK II. Use the convenient
ONLINE REGISTRATION at www.mindprint.com
If you are unable to register online, please fill out the
enclosed warranty card completely and mail or fax it
to us. The registration is only valid if the warranty
registration card is filled out and returned to
MindPrint® or the device is registered via Internet
within 30 days of the date of purchase. We are also
interested in learning who uses our devices with
the aim of using this information to help us design
future products. Your data is of course protected by
privacy laws.
Thank you.
MindPrint®
Technical Service
Postfach 1509
D-66595 St. Wendel, Germany
Fax: +49 6851 905 100
ENGLISH
Don´t just dream it ... record it!
Evolution rather than revolution
If it isn’t broke, don’t fix it: The concept behind the first EN-VOICE® was a stunning success,
so we didn’t change it. Rather than radical redesign, the new design features are the product
of painstaking detailing, particularly in response to our customers’ wishes and suggestions for
improvement. So, how does the successor differ from the first EN-VOICE®? The handling concept, equalizer and revolutionary tube circuitry have remained the same, though the circuitry
has seen some design improvements. The input section, however, was developed anew from
the bottom up and now offers an integrated balanced INSERT, while the compressor now
features eight convenient presets. In addition to redesigning the front panel, we improved
the array and labeling of control features, and endowed the chassis with easily attachable
rack mounts to desktop-enable the device.
Independence Day
The EN-VOICE® MK II is the first channel strip that is a match for laptops when it comes to
mobility. Road-ready courtesy of its USB and automatic switched mode power supply, it goes
where you go, operating reliably when you get there. Though the USB interface is now as
commonplace on the computer as jacks on a mixer, unfortunately, no USB interface to date
has been able to transmit the EN-VOICE® MK II’s sonic qualities loss-free. Thanks to some pioneering engineering, this problem has been solved with the optional DI-MOD USB. A further
stride toward total independence is the automatic switched mode power supply, which frees
the EN-VOICE® MK II from the constraints of local mains voltage and protects it against fluctuating current and power surges.
The power unit even enhances tone: Tubes are very sensitive to line voltage fluctuations.
This unit maintains a steady power supply of 250 volts, preventing sound degradation
caused by fluctuating current.
3
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 4
MindPrint® – It’s all in the name!
Printing musical ideas onto hard disk in highest sound quality has never been so easy and
convenient. That, in a nutshell, is what the brand name MindPrint means. The combination of
a tube-driven preamp with a USB interface and a switched mode power supply transforms
the EN-VOICE® MK II from a reliable tool into a very personal instrument, totally independent
of operating voltage and computer interface. Wherever you go, it goes with you, giving your
creativity free rein. Everywhere, all the time - even on a trip around the globe.
Here’s wishing you lots of fun and success with the MindPrint EN-VOICE® MK II!
Table of Contents
1. Input Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2. Equalization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
3. Dynamic Processing . . . . . . . . . . . . . . . . . . . . . . 10
4. Output Section . . . . . . . . . . . . . . . . . . . . . . . . . 13
5. AC Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6. Tips and Tricks . . . . . . . . . . . . . . . . . . . . . . . . . . 14
7. Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . 63
4
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 5
1. Input Section
The EN-VOICE® MK II features a complete input
section consisting of a studio level line input,
a high-ohm instrument input and a low-noise
microphone input with switchable phantom
power for condenser microphones. You can also
retrofit a digital input by installing the DI-MOD
expansion module.
Connecting microphones:
On the rear panel of the EN-VOICE® MK II you’ll
find an XLR port for connecting microphones.
It is designed to accept all types of microphones.
Connect condenser microphones to the switchable 48-volt phantom power port on the front
panel. The EN-VOICE® MK II offers switchable 20dB signal dampening for recording very loud
signals. The input impedance is 5 k-ohms.
Handling:
INPUT SELECT: Select the microphone input by
setting the INPUT SELECT button to the MIC
position.
MIC GAIN: Determines the pre-amplification
level within a range of +19 dB to +75 dB.
48 V: Activates phantom power when switched
from the OFF position to the 48V position.
CAUTION:
Do not connect line level devices to the microphone
port because this may damage the EN-VOICE® MK II.
Never activate phantom power when unbalanced
microphones or ribbon microphones are connected!
QUESTION
At 10 k-ohms, the microphone input’s impedance is
considerably higher than that of standard microphone preamps. Why did MindPrint choose to deviate
from the standard value range of 600 to 1000 ohms?
ANSWER
Rather than being constant, the impedance of microphones depends on the frequency. It is not uncommon for impedance spikes to surge up to 1,000 ohms
within microphones’ frequency response range. These
peaks are cut if the microphone preamp’s input
impedance is lower, which of course automatically
changes frequency response. Because these peaks
tend to occur at higher frequencies, this de facto
auto dampening of low-impedance preamp sacrifices
brilliance. Courtesy of its high-impedance design, the
EN-VOICE® MK II can handle extreme peaks, preventing high frequency loss. This ensures microphones,
and particularly dynamic microphones, deliver a
fresher, more natural-sounding signal.
Condenser microphones also sound better because
their amps can operate with a lower load, thereby
generating less noise.
-20 dB: Cuts input levels by 20 dB when switched
from OFF to -20 dB.
5
ENGLISH
1.1 Microphone Input
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 6
1.2 Instrument Input
Connecting instruments:
A 1/4” jack on the front panel accepts instruments.
Handling:
INPUT SELECT: Select the instrument input by
setting the INPUT SELECT button to LINE/INSTR.
When you plug a cord into the INSTRUMENT IN
jack, the EN-VOICE® MK II automatically switches
to the instrument input, simultaneously deactivating the line and digital inputs.
INPUT SENSITIVITY
This input’s sensitivity was tweaked specifically to
accept guitar and bass signals directly. With an impedance of 1 mega ohm, the instrument input does not
dampen excessively your instrument’s pickup. This
means that the EN-VOICE® MK II is well-suited for use
in an instrument rack.
LINE GAIN: Determines the amount of cut or
boost within a range of -∞ to +22 dB.
1.3 Line Input
Connecting line sources:
Located on the rear panel of the EN-VOICE® MK II,
the line input features two connectors, a balanced
XLR port and a balanced 1/4" jack. You can also
connect unbalanced cables to both inputs.
Handling:
INPUT SELECT: Select the line input by setting
the INPUT SELECT button to LINE/INSTR. It is
only active when the INSTRUMENT input is not
in use!
boost within a range of -∞ to +22 dB.
6
INFO
The XLR port’s pin assignments comply with the
international IEC 268-12 norm. In accordance with
this norm, pin 1 is the ground, pin 2 carries the positive signal and pin 3 the negative signal. Be sure to
bridge pin 1 and pin 3 when using an unbalanced
circuit. The stereo 1/4" jack’s tip carries the positive
signal, its ring carries the negative signal, and the
ground circuit is routed via the sleeve. When you
insert an unbalanced mono plug, the input automatically switches to unbalanced operating mode.
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 7
1.4 Digital Input
Connecting digital sources:
The MindPrint DI-MOD can be installed into a
slot in the rear panel, which lets you connect
digital devices to the EN-VOICE® MK II. You’ll find
the digital interface’s connectors on the actual
DI-MOD. The digital output is wired in parallel to
the analog output.
Handling:
INPUT SELECT: Select the digital input by setting
the INPUT SELECT button to DIGITAL.
Optional DI-MOD
If you want to make the most of the sound quality
that the EN-VOICE® MK II has to offer, be sure to
install the DI-MOD. You can view the various models
of DI-MOD at www.mindprint.com
QUESTION
Why is the digital interface not hard-wired into the
device?
ANSWER
The EN-VOICE® MK II is an analog device, and as such
will continue to serve its designated purpose for years
to come. Digital interfaces are subject to change as
digital technology advances. This is why the DI-MOD
is replaceable. Besides, this lets you decide for yourself which model serves your purposes best.
1.5 Selecting LED Meter
Modes
This LED meter indicates the level of the input or
output signal, depending on the METER ASSIGN
button’s setting. The yellow LEDs indicate the
EN-VOICE® MK II’s headroom; the red LEDs indicate the saturation level.
ENGLISH
boost within a range of -00 to +22 dB.
LED Chain
This meter works like meters found on digital devices
(for example, a DAT recorder): Distortion is imminent
when the meter’s red OVER LED. Though it is advisable to set the input and output signals to the highest
possible level in order to exploit all the available
headroom, ensure the level remains below 0 dB.
The chain’s top (red) LED should not light up even
at signal peaks.
Handling:
METER ASSIGN: Switches the level meter so that
it indicates either the input or output signal. For
the record, the meter indicates the input signal
when set to INPUT, and the output signal when
set to OUTPUT.
7
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 8
1.6 Low-Cut Filter
Following the input stage in the signal path is a
(bass cut) filter. Its limiting frequency of 80 Hz
suppresses low-frequency noise such as footsteps
or popping sounds.
Handling:
LOW CUT: Activates the filter.
1.7 Insert
Connecting signal processors:
On the rear panel, you’ll find SEND and a
RETURN jacks enabling you to insert signal processors into the EN-VOICE® MK II’s signal path.
Handling:
When you plug a cord into the RETURN jack, the
EN-VOICE® MK II automatically patches the insert
into the signal path at a point located between
the low-cut-filter and the equalizer.
8
INFO
These connectors are configured as stereo 1/4" jacks.
The positive signal is routed via the tip, the negative
signal via the ring, and the ground via the sleeve.
When you insert an unbalanced mono plug, the
input automatically switches to unbalanced operating
mode.
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 9
2. Equalization
The equalizer consists of one each semi-parametric band for low and high frequencies as well as
one fully parametric middle frequency band.
All three EQ bands were implemented in the
form of bell filters.
Handling:
ON: Activates the band.
FREQ Hz: Determines the bell curve’s center
frequency within a range of 20 to 300 Hz.
INFO
Though the LF band’s width (also called quality or
Q-factor) is not variable, you still enjoy flexible EQ
options because frequencies are boosted across a
broad range. Conversely, frequencies are cut in a
very narrow band. This lets you introduce that typical
bottom-end warmth by boosting low frequencies
across the board and pinpoint and suppress undesirable frequencies with precision.
ENGLISH
2.1 LF - The Low Frequency
Band
LEVEL dB: Controls the amount of cut or boost
within a range of +/- 15 db.
2.2 MF - The Middle Frequency
Band
Handling:
ON: Activates the band.
INFO
With its variable frequency range of 100 Hz and 11 kHz,
the mid band extends well into the low and high
ranges. This EQ is your universal sound-sculpting
tool. Its variable bandwidth lets you dial in a Q-factor
between a third (or mediant) and six octaves to target
cuts within a narrow band or equalize frequencies on
a very wide scale.
FREQ Hz: Determines the bell curve’s center
frequency within a range of 100 Hz to 11 kHz.
Q: Determines the bell curve’s bandwidth within
a value range of 3 (1/3 octave) to 0.15 (6 octaves).
2.3 HF - The High Frequency
Band
Handling:
ON: This button activates the band.
INFO
At settings above 20 kHz, the filter’s center frequency
lies outside the range of human hearing, and it
responds like a shelving filter. Its quality is fixed,
remaining the same when frequencies are cut and
boost.
FREQ kHz: Determines the bell curve’s center
frequency within a range of 1.6 to 22 kHz.
9
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 10
3. Dynamic
Processing
Output
1:1
Compression
∞
Threshold
Input
Output
normal
Soft Knee Characteristic
Input
The tube compressor gives you the best of both
worlds—the precision of a high-quality semiconductor circuit with the silken sound that only a
vacuum tube can deliver. The circuitry developed
by MindPrint lets you control compression and
tube saturation separately. To achieve the most
inconspicuous compression possible, the
EN-VOICE® MK II works with a soft knee characteristic: When a signal's level nears the threshold
value, the compression rate steadily increases.
When the signal level finally exceeds the threshold
value, it is compressed at the ratio that you have
dialed in. Even when compressed heavily, signals
are gently squeezed rather than crushed when
the signal rises above the threshold.
Handling:
ON: Activates the compressor.
THRESHOLD: Sets the compressor’s threshold
within a range of +2 dB to -28 dB.
The compressor processes all signals whose level
exceeds the threshold value. Depending on the
defined threshold value, the signal may also be
boosted before it is routed to the tube. Signals
whose levels remain below the threshold value
are not processed.
RATIO: Determines the relationship between – or
ratio of – the input and output levels of all signals
exceeding the threshold value. Control range:
1:1 (no compression) to infinite (limiter settingthe output level cannot be increased any further).
GAIN REDUCTION LED CHAIN: Gives you a
visual indication of the amount that the compressor is trimming off the signal level.
TUBE SATURATION %: Controls the amount of
tube saturation within the compressor for all
signals exceeding the threshold value. This lets
you determine precisely the amount of harmonic
overtones that tube saturation generates.
The control range extends from 0% to 100%.
10
A WORD ABOUT THE TUBE
The overtones that tubes generate when driven hard
are what makes them so special. While semiconductors tend to produce harsh, grating distortion, tubes
deliver warm, silken sound that is considered highly
desirable by recordists. Though all-tube circuits deliver a warmer sound, they also have some drawbacks;
for example, they are noisier than solid state circuits.
In the EN-VOICE® MK II, the tube is hard-wired to a
VCA (short for voltage-controlled amplifier, this is the
compressor’s controlling element). Courtesy of this
VCA, the compressor’s response helps shape the tone
generated by the tube. This puts into your hands a
compressor that combines the trademark precision
of a semiconductor circuit with the characteristic
response of all-tube devices. Model 12AX7A tubes are
triodes that are valued for their sonic qualities and
used in many other devices. The popularity of this
model has an agreeable side effect - when a tube
requires a replacement, 12AX7A’s are easy to find
and affordably priced.
BIAS POINT
The threshold value depends on the input level and
equalizer levels. For example, if you turn the input
level well down, you must adjust the Threshold level
accordingly.
LEVEL REDUCTION
A Ratio setting of 2:1 means that the output level
increases by just 1 dB when the input level rises by
2 dB; 5:1 means that it takes a 5 dB boost in input level
to increase the output level by 1 dB. Note that you
don’t have to reduce the gain manually because the
EN-VOICE MK II adjusts the overall level automatically.
TUBE SATURATION
A good analogy for tube saturation is the behavior of
a guitar string. Both generate a fundamental frequency and a series of harmonics. In the case of the string,
harmonics are the frequencies produced by half the
string, a third, a quarter and so forth. In both cases,
the relative levels of harmonics are decisive in shaping tone. It takes the right mix to create a signal
that pleases the human ear.
INFO
High-energy low-frequency signals can cause the
compressor to generate undesirable pumping effects.
For this reason, the compressor is equipped with a filter designed to make it is less responsive to low frequencies, yielding the kind of natural-sounding compression our ears are accustomed to hearing. Because
this design simulates a natural function of the human
ear, this filter circuit enhances the tone of almost
every signal.
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 11
FILTER: Switches the compressor’s side chain
filter on. When the filter is activated, lower
frequencies have less influence on compression,
which yields a more balanced sonic image,
particularly in the mid and high frequency ranges.
Because the filter is wired into the control circuitry
rather than the signal path, it influences the
compressor’s response rather than the actual
sound of the signal.
Type: low-cut, shelving
Corner frequency: 300 Hz
Slope: 6 dB/octave
Adaptive Response Circuit
The EN-VOICE® MK II is equipped with an Adaptive
Response circuit developed by MindPrint®. It works
with several mutually influencing time constants,
using an intelligent attack and release automatism to
prevent undesirable side effects. The default control
time changes adaptively so that the compressor
responds faster to brief signals and slower to sustained signals. A standard compressor’s response to
dense, powerful audio material is to cut signal peaks
radically, which results in a pumping effect. This
adaptive circuit offers an additional mechanism that
catches fast impulses regardless of the basic compressor setting.
INFO
The differences between presets are most clearly
audible at low Threshold and high Ratio settings.
The easiest way to find the best setting is to twist
these two knobs to the far right and gradually back
them off until you achieve the desired effect. Setting
the knobs to the 12-clock position generally yields
inconspicuous results. If you want a more pronounced
effect, turn the Threshold down (twist the knob
clockwise!) and then adjust the Ratio knob.
COMPRESSION MODE: Selects eight presets for
the compressor’s program-dependent control
time tracking.
11
ENGLISH
TUBE SAT: Indicates the degree of distortion in
threes levels - green, yellow and red. Overtones
are hardly audible when the meter is in the
green. When in the yellow, saturation is clearly
audible. When in the red, you will hear overtones
as distortion.
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 12
Vocal 1, Dynamic Voice: This preset offers neutral
dynamic processing, gently and unobtrusively
boosting loudness and density.
V1
It is best suited for soft, natural sounds typical of very
dynamic musical styles, for example, jazz or songs
played principally on acoustic instruments.
Vocal 2, Voice Over: This preset offers very loudsounding compression to beef up the sound of
the natural voice.
V2
It is excellent for elaborately arranged pop vocals and
advertising voice-overs. Low Threshold and high
Ratio settings make vocal tracks jump right out of
the mix.
Vocal 3, Classical Voice: Rather than changing
the human voice’s natural character, this preset
gently balances out differences in level.
TIP
The names of the presets are merely something to go
by. When searching for the right sound, nothing prevents you from processing a vocal track with a preset
intended for a guitar or bass track. The same holds
true for every signal source imaginable, from a speaker to a saxophone or synth. Feel free to experiment.
Guitar 1, Funky: This one’s perfect for emphasizing the crisp attack of a funky guitar, boosting
signal level and pushing the track to the forefront of the mix.
Guitar 2, Overdrive: This preset fattens up distorted riffs, adding punch to single-note lines and
rounding out jazz chords.
Bass 1, Slap: Tweaked for slap styles, this
preset adds density to the bass signal ensuring
a smoother sound in the mix without introducing
undesirable side effects.
Bass 2, Fingered: This preset boosts string attack,
making the instrument feel more responsive
while recording and the bass track cut through
the mix better.
Percussive: Fine-tuned specifically for recording
drum and percussion sounds, this preset elicits
very fast compressor response while retaining a
natural-sounding attack.
Preset
V1:
V2:
V3:
G1:
G2:
B1:
B2:
P:
12
Description
Vocal clear, standard
Vocal fat, "analog"
Vocal natural
Guitar percussive, funky
Guitar soft
Bass percussive, slap
Bass gritty
Percussion fat and punchy
Attack
med.
long
short
med.
med.
long
short
short
The table depicts recommended settings for TUBE
SAT, RATIO and FILTER parameters.
Release
short
short
med.
long
short
med.
short
short
TubeSat
25%
50%
25%
25%
50%
25%
75%
0%
Ratio
2.5
3.5
1.7
1.7
1,7
1.7
2.5
5.0
Filter
on
on
on
on
off
off
off
on
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 13
4.1 OUTPUT
Connecting outboard gear:
The balanced XLR output serves as a recording
out for connected recording systems, mixers or
external converters. The balanced 1/4” jack output
is an analog monitor output. The two outputs
may be used simultaneously.
Handling:
OUTPUT: Determines output volume within
a range of -∞ to +8 dB. Unity gain is achieved
at the 0 setting.
4.2 BYPASS
Handling:
BYPASS: Removes all of the EN-VOICE® MK II’s
processing components and the Output knob
from the signal path.
INFO
If you insert an unbalanced cord equipped with 1/4”
plugs into the output, say to connect a monitoring
system, the signal patched to the XLR port will also
be unbalanced. If you have no choice but to use an
unbalanced monitor signal but require a balanced
signal from the XLR port, you can employ a standard
unbalanced 1/4” jack cord for your monitor and solder
a stereo 1/4” jack plug to the end of cord end to be
inserted into the EN-VOICE® MK II’s output. Do not
wire a terminal to the RING. The TIP carries the signal,
the SLEEVE is the ground, and the signal of the XLR
socket remains balanced.
TIP
As described in section 1.5 Selecting LED Meter
Modes, you can assign the level meter to the input
oroutput. This means that the meter indicates either
the post preamp level or the output level of the
EN-VOICE® MK II.
CAUTION
Depending on settings, there may be a considerable
difference in the levels of the processed and original
signals. BYPASS serves principally to A/B or compare
the processed and original signals. If you want to use
the Output knob as an “alternative” volume control,
it is a good idea to switch off the individual processing stages for purposes of comparison.
5. AC Power
The EN-VOICE® MK II is connected to a wall outlet
or mains supply via a standard power cable connected to the AC power socket.
If you encounter a ground loop, you can use the
Ground Lift switch to sever the signal ground
from the device's chassis ground. A ground loop
is pretty easy to identify - the device emits
annoying hum. In this case, set this switch to the
position where the noise is canceled out.
13
ENGLISH
4. Output Section
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 14
6 Tips and Tricks
6.1 Switching noise
All of the EN-VOICE® MK II On buttons are real
hardware switches. This means that, rather than
just being deactivated, the processing stages are
actually removed from the signal path. While
removing unnecessary stages from the circuit
enhances audio quality, these switches sometimes
cause undesirable clicking or popping noises,
which are produced by sudden surges in amplitude. Your best bet is to forget about switching
individual equalizer bands or the entire effects
chain on and off during recording or processing
with the EN-VOICE® MK II.
6.2 Over-the-top distortion
The tube compressor acts upon all signals that lie
above the threshold value. Moreover, the saturation of the tube will fluctuate depending on how
high the signal level is. To keep the saturation
fairly even, the compressor should be used to
keep the signal level as steady as possible. If you
dial in a low threshold value and a high saturation level, the tube will be driven hard enough
to produce fairly heavy distortion at signal peaks.
In this case, you should increase the compression
ratio to reduce these signal peaks. If you don't
want quite this much signal processing, you
should dial in lower threshold and saturation
values.
6.3 The EN-VOICE® MK II
in Live Applications
Although the EN-VOICE® MK II was primarily
developed for recording purposes, it actually
wears many hats - you'll find that it is an excellent
tool for live applications. If you are the proud
owner of a guitar rack system, you can patch it
in post-preamp and pre-power amp to compress
your instrument's signal. When you play gigs that
you can't be bothered to tote your entire rig to,
simply plug your guitar into the instrument input
and feed the output signal directly to the mixing
console; the EN-VOICE® MK II thus becomes a convenient tube DI box. For processing vocals, you
can patch the EN-VOICE® MK II into a mixer insert
just as you would an effects device, so that the
amplified sound of your voice enjoys the benefits
of those desirable tube characteristics.
14
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 63
All data related to levels is referenced to 0 dBu (0.775V RMS).
LINE IN:
Connections:
Input type:
Input impedance:
Min. Input level:
Max. Input level:
Sensitivity:
Gain:
XLR (pin 1 = ground; pin 2 = +; pin 3 = -) and
1/4" (tip = +; ring = -; sleeve = ground)
electronically balanced and floating
44 kohms
-5.4 dBu @ Line Gain +22 dB
+20.5 dBu @ Line Gain <-10 dB
0 dB
∞- to +22.5 dB
MID EQ:
Type:
Switchable:
Center frequency:
Boost:
Cut:
Slope:
Bell
on or off
adjustable from 100 Hz to 11 kHz
15 dB
15 dB
3 dB/oct. - 24 dB/oct. (dependent on setting of Q-factor)
HIGH EQ:
Type:
Switchable:
Center frequency:
Boost:
Cut:
Slope:
Technical D at a
7. Technical Specifications
Bell
on or off
adjustable from 11 kHz to 22 kHz
15 dB
15 dB
6 dB/ oct.
MIC IN:
Connection type:
Input type:
Input impedance:
Min. Input level:
Max. Input level:
Gain:
XLR (pin 1 = ground; pin 2 = +; pin 3 = -)
10 kohms
-55.4 dBu @-20 dB Pad OFF
25 dBu @-20 dB Pad ON
+25 to +72 dB
INSTRUMENT IN:
Connection type:
Input type:
Input impedance:
Min. Input level:
Max. Input level:
Sensitivity:
1/4" (tip = +; sleeve = -)
unbalanced
470 kohms
-11 dBu @ Line Gain +22 dB
3 dB
DIGITAL IN:
only with optional DI-MOD
COMPRESSOR
Switchable:
on or off
TUBE SAT:
Harmonic distortion: adjustable between 1% and 100%
THRESHOLD:
adjustable between +2 dB and -28 dB
COMPRESSION:
adjustable from 1:1 to Åá:1
Attack/Release:
switchable, 8 Presets
FILTER:
switchable on or off, LOW-CUT 300 Hz, 6 dB/octave
INSERT SEND:
Connections:
Type Output:
Output impedance:
Max. output level:
220 ohms
+19 dBu
LINE OUT:
INSERT RETURN
Connections:
Input type:
Input impedance:
Max. Input level:
Sensitivity:
Connections:
55 kohms
+17.5 dBu
0 dB
BASS CUT:
BYPASS:
Switchable:
on or off
Shelving frequency: 80 Hz
Slope:
12 dB/ oct.
BASS EQ:
Type:
Switchable:
Center frequency:
Boost:
Boost slope:
Cut:
Cut slope:
XLR (1 = ground; 2 = +; 3 = -) and
Type Output:
Output impedance: 220 ohms
Max. output level: +19 dBu
Gain:
-∞ to +6 dB
Bell
on or off
adjustable from 20 Hz to 300 Hz
15 dB
6 dB/ oct.
15 dB
12 dB/ oct.
switchable:
on or off
max. current draw: 132 mA ( 170 mA mit DI-MOD ) @ 240 volts AC
max. power cons: 44 VA
Primary Fuse:
T 1.25 A (slow blow)
Dimensions:
Width:
Height:
Depth:
Weight:
482 mm (19")
44 mm (1 3/4")
238 mm (9 2/5")
3.44 kg (7 3/5 lbs.)
OPTIONS:
DI-MOD USB:
DS 1-P:
2 channels AD/DA, up to 24 bits, 96 kHz,
110 dB (a) dynamic range, USB IN/OUT,
Additional S/PDIF Out, Stereo Monitor Out,
Zero Latency Monitoring
Perspex Desktop Stand , dimensions: 260 x 90 x 8 mm
63
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 64
7. Technische Daten
Alle Daten beziehen sich auf einen Referenzpegel von 0 dBu (0.775V RMS).
LINE IN:
Bauart:
Eingang:
Eingangsimpedanz:
Min. Eingangspegel:
Max. Eingangspegel:
Empfindlichkeit:
Verstärkung:
XLR (pin 1 = Masse; pin 2 = +; pin 3 = -) und
1/4" (Tip = +; Ring = -; Schaft = Masse)
elektronisch symmetriert
44 kohm
-5.4 dBu @ Line Gain +22 dB
0 dB
-∞ to +22.5 dB
MID EQ:
Typ:
Schaltbar:
Center-Frequenz:
Verstärkung:
Absenkung:
Flankensteilheit:
Glockenfilter
An/Aus
einstellbar von 100 Hz bis 11 kHz
15 dB
15 dB
3 dB/ Oktave - 24 dB/ Oktave. (einstellbar, Q-Factor)
HIGH EQ:
Type:
Switchable:
Center-Frequenz:
Verstärkung:
Absenkung:
Flankensteilheit:
Glockenfilter
on or off
einstellbar von 11 kHz bis 22 kHz
15 dB
15 dB
6 dB/ oct.
MIC IN:
Bauart:
Eingang:
Eingangsimpedanz:
Min. Eingangspegel:
Max. Eingangspegel:
Verstärkung:
XLR (pin 1 = ground; pin 2 = +; pin 3 = -)
10 kohm
+25 to +72 dB
INSTRUMENT IN:
Bauart:
Eingang:
Eingangsimpedanz:
Min. Eingangspegel:
Max. Eingangspegel:
Empfindlichkeit:
1/4" (tip = +; sleeve = -)
unsymmetrisch
470 kohm
3 dB
DIGITAL IN:
nur mit optionalem DI-MOD
COMPRESSOR
Schaltbar:
An/Aus
TUBE SAT:
Harmonische Verzerrung:
THRESHOLD:
COMPRESSION:
Attack/Release:
FILTER: schaltbar:
einstellbar von 1% bis 100%
einstellbar von +2 dB bis -28 dB
einstellbar von 1:1 bis Åá:1
schaltbar, 8 Presets
An/Aus, LOW-CUT 300 Hz, 6 dB/ Oktave
INSERT SEND:
Bauart:
Ausgang:
Ausgangsimpedanz:
Max. Ausgangspegel:
220 ohm
+19 dBu
LINE OUT:
INSERT RETURN
Bauart:
Eingang:
Eingangsimpedanz:
Max. Eingangspegel:
Empfindlichkeit:
Bauart:
55 kohm
+17.5 dBu
0 dB
BASS CUT:
Schaltbar:
Einsatzfrequenz:
Flankensteilheit:
BYPASS:
An/Aus
80 Hz
12 dB/ Oktave.
BASS EQ:
Typ:
Schaltbar:
Center-Frequenz:
Verstärkung:
Flankensteilheit:
Absenkung:
Flankensteilheit:
Ausgang:
Ausgangsimpedanz:
Max. Ausgangspegel:
Verstärkung:
XLR (1 = Masse; 2 = +; 3 = -) und
220 ohm
+19 dBu
-∞ to +6 dB
Glockenfilter
An/Aus
einstellbar von 20 Hz bis 300 Hz
15 dB
6 dB/ Oktave.
15 dB
12 dB/ Oktave.
Schaltbar:
An/Aus
max. Stromaufnahme:
132 mA ( 172 mA mit DI-MOD ) @ 240 Volt AC
max. Leistungsaufnahme: 44 VA
Primärsicherung:
T 1.25 A (träge)
Maße:
Breite:
Höhe:
Tiefe:
Gewicht:
482 mm (19")
44 mm (1 3/4")
238 mm (9 2/5")
3.44 kg (7 3/5 lbs.)
OPTIONS:
DI-MOD USB:
DS 1-P:
64
2 Kanäle AD/DA, bis zu 24 Bit, 96 kHz
110 dB (a) Dynamikumfang, USB IN/OUT,
zusätzlich S/PDIF Out, Stereo Monitor Out,
Plexiglas Desktop Stand, Maße: 260 x 90 x 8 mm
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 65
Toutes les données se basent sur un niveau de référence de 0 dBu (0,775 V RMS).
LINE IN :
Type de connexion :
Entrée :
Impédance d'entrée :
Niveau d'entrée min. :
Niveau d'entrée max. :
Sensibilité :
Amplification :
XLR (borne 1 = masse ; borne 2 = + ; borne 3 = -)
et 1/4" (pointe = + ; anneau = - ; axe = masse)
électroniquement symétrique
44 kohms
-5,4 dBu pour Line Gain +22 dB
+20,5 dBu pour Line Gain <-10 dB
0 dB
-∞ à +22,5 dB
MID EQ :
Type :
Commutable :
Fréquence centrale :
Amplification :
Abaissement :
Pente du signal :
filtre à cloche
on/off
réglable de 100 Hz à 11 kHz
15 dB
15 dB
de 3 dB/octave à 24 dB/octave (réglable, facteur Q)
HIGH EQ :
Type :
Commutable :
Amplification :
Abaissement :
Pente du signal :
Technical D at a
Caractéristiques techniques
filtre à cloche
on/off
réglable de 11 kHz à 22 kHz
15 dB
15 dB
6 dB/octave
MIC IN :
Type de connexion :
Entrée :
Amplification :
XLR (borne 1 = masse ; borne 2 = + ; borne 3 = -)
10 kohms
-55,4 dBu pour -20 dB Pad OFF
25 dBu pour -20 dB Pad ON
de +25 à +72 dB
INSTRUMENT IN :
Type de connexion :
Entrée :
Sensibilité :
1/4" (pointe = + ; tige = -)
asymétrique
470 kohms
-11 dBu pour Line Gain +22 dB
+23,5 dBu pour Line Gain <-15 dB
3 dB
DIGITAL IN :
uniquement avec DI-MOD (en option)
1/4" (pointe = + ; anneau = - ; axe = masse)
55 kohms
+17,5 dBu
0 dB
on/off
80 Hz
12 dB/octave
BASS EQ :
Type :
Commutable :
Amplification :
Pente du signal :
Abaissement :
Pente du signal :
on/off
TUBE SAT :
Distorsion harmonique :
THRESHOLD (seuil) :
COMPRESSION :
Attaque/relâchement :
FILTRE : commutable :
réglable de 1% à 100%
réglable de +2 dB à -28 dB
réglable de 1:1 à Åá:1
commutable, 8 presets
on/off, passe haut 300 Hz, 6 dB/octave
INSERT SEND :
Type de connexion :
Sortie :
Impédance de sortie :
Niveau de sortie max. :
Sortie :
Impédance de sortie :
Niveau de sortie max. :
Amplification :
1/4" (pointe = + ; anneau = - ; axe = masse)
220 ohms
+19 dBu
XLR (1 = masse ; 2 = + ; 3 = -)
et 1/4" (pointe = + ; anneau = - ; axe = masse)
220 ohms
+19 dBu
de -∞ à +6 dB
BYPASS :
BASS CUT :
Commutable :
Fréquence d'attaque :
Pente du signal :
Commutable :
LINE OUT :
Type de connexion :
INSERT RETURN :
Type de connexion :
Entrée :
Sensibilité :
COMPRESSEUR
filtre à cloche
on/off
réglable de 20 Hz à 300 Hz
15 dB
6 dB/octave
15 dB
12 dB/octave
Commutable :
on/off
Consommation de
courant max. :
132 mA (172 mA avec DI-MOD ) pour 240 volts CA
Puissance absorbée max. : 44 VA
Fusible primaire :
T 1,25 A )fusible temporisé)
Dimensions :
largeur :
hauteur :
profondeur :
Poids :
482 mm ;
44 mm ;
238 mm
3,44 kg
Options
USB DI- MOD :
DS 1-P :
2 canaux AN/NA, jusqu’à 24 bits, 96 kHz
Spectre dynamique: 110 dB (a) USB IN/OUT,
S/PDIF Out supplémentaire, Moniteur Stereo Out,
surveillance en temps réel
stand desktop en plexiglas,
dimensions : 260 x 90 x 8 mm
65
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 66
Caratteristiche Tecniche
I valori seguenti si intendono rispetto a un livello di riferimento
di 0 dBu (0,775V RMS).
LINE IN:
Tipo di costruzione:
Ingresso:
Impedenza di ingresso:
Minimo livello di ingresso:
Massimo livello di ingresso:
Sensibilità:
Amplificazione:
XLR (pin 1 = massa; pin 2 = +; pin 3 = -)
e 1/4" (punta = +; annello = -; manico = massa)
simmetria elettronica
44 kOhm
-5,4 dBu @ Line Gain +22 dB
0 dB
-∞ a +22.5 dB
MIC IN:
Ingresso:
Amplificatzione:
XLR (pin 1 = massa; pin 2 = +; pin 3 = -)
10 kOhm
+25 a +72 dB
INSTRUMENT IN:
Ingresso:
Sensibilità:
1/4" (punta = +; manico = -)
assimmetrico
470 kOhm
+23,5 dBu @ Line Gain <-15 dB
3 dB
DIGITAL IN:
soltanto con module opzionale DI-MOD
HIGH EQ:
Tipo:
Commutabile:
Frequenza centrale:
Aumento:
Reduzione:
Tasso di accrescimento:
filtro a campana
acceso/spento
regolabile da 11 kHz a 22 kHz
15 dB
15 dB
6 dB/ottava
COMPRESSOR
Commutabile:
acceso/spento
TUBE SAT:
Distorsione armonica:
THRESHOLD:
COMPRESSION:
Attack/Release:
FILTER: commutabile:
regolabile da 1% a 100%
regolabile da +2 dB a -28 dB
regolabile da 1:1 a Åá:1
commutabile, 8 preset
acceso/spento, LOW-CUT 300 Hz, 6dB/ottava
INSERT SEND:
Uscita:
Impedenza di uscita:
Massimo livello di uscita:
1/4" (punta = +; annello = -; manico = massa)
220 ohm
+19 dBu
LINE OUT:
Uscita:
Impedenza di uscita:
Massimo livello di uscita:
Aumento:
XLR (1 = massa; 2 = +; 3 = -) e
e 1/4" (punta = +; annello = -; manico = massa)
220 ohm
+19 dBu
-∞ a +6 dB
BYPASS:
Commutabile:
acceso/spento
INSERT RETURN
Ingresso:
Sensibilità:
1/4" (punta = +; annello = -; manico = massa)
55 kOhm
+17.5 dBu
0 dB
BASS CUT:
Commutabile:
Frequenza di lavoro:
Massimo assorbimento
di corrente:
Massimo assorbimento
di potenza:
Fusibile principale:
132 mA ( 172 mA con DI-MOD ) @ 240 Volt AC
44 VA
T 1,25 A (ritardato)
Dimensioni:
acceso/spento
80 Hz
12 dB/ottava
larghezza:
altezza:
profondità:
Peso:
filtro a campana
acceso/spento
regolabile da 20 Hz a 300 Hz
15 dB
6 dB/ottava
15 dB
12 dB/ottava
MODULI OPZIONALI
482 mm (19")
44 mm (1 3/4")
238 mm (9 2/5")
3,44 kg (7 3/5" lbs.)
BASS EQ:
Tipo:
Commutabile:
Frequenza centrale:
Aumento:
Reduzione:
MID EQ:
Tipo:
Commutabile:
Frequenza centrale:
Aumento:
Reduzione:
66
filtro a campana
acceso/spento
regolabile da 100 Hz a 11 kHz
15 dB
15 dB
3 dB/ottava a 24 dB/ottava (regolabile, fattore Q)
DI-MOD USB:
DS 1-P:
2 canali AD/DA, fino a 24 Bit, 96 kHz
Spettro dinamico: 110 dB (a), USB IN/OUT,
in addizione S/PDIF Out, Stereo Monitor Out,
Desktop-stand in plexiglas,
dimensioni: 260 x 90 x 8 mm
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 67
Todos los datos son respecto al nivel de referencia de 0 dBu (0.775V RMS)
LINE IN:
Tipo constructivo:
Entrada:
Impedancia de entrada:
Nivel de entrada mín:
Nivel de entrada max.:
Sensibilidad:
Amplificación:
XLR (pin 1 = Masa; pin 2 = +; pin 3 = -)
yd 1/4" (Tipo = +; Anillo = -; Mango = Masa)
electrónicamente simetrizada
44 kohmios
-5.4 dBu @ ganancia línea +22 dB
+20.5 dBu @ ganancia línea -10 dB
0 dB
-∞ to +22.5 dB
MIC IN:
Tipo constructivo:
Entrada:
Amplificación:
XLR (pin 1 = masa; pin 2 = +; pin 3 = -)
10 kohmios
+25 a +72 dB
HIGH EQ:
Tipo:
Conmutable:
Frecuencia central:
Amplificación:
Descenso:
Pendiente de flancos:
Filtro de campana
on o off
ajustable de 11 kHz hasta 22 kHz
15 dB
15 dB
6 dB/ oct.
COMPRESOR
Conmutable:
Technical D at a
Datos técnicos
Encendido/ Apagado
TUBE SAT:
Distorsión armónica:
THRESHOLD:
COMPRESION:
Attack/Release:
ajustable de 1% hasta 100%
ajustable de +2 dB hasta -28 dB
ajustable de 1:1 hasta Åá:1
conmutable, 8 Presets
FILTRO:
Conmutable:
Encendido / apagado, LOW-CUT 300 Hz,
6 dB/ Octavos
INSERT SEND:
INSTRUMENT IN:
Tipo constructivo:
Entrada:
Sensibilidad:
1/4" (Tipo = +; manguito = -)
asimétrico
470 kohmios
-11 dBu @ ganancia línea +22 dB
+23.5 dBu @ ganancia línea -15 dB
3 dB
DIGITAL IN:
Sólo con DI-MOD opcional
INSERT RETURN
Tipo constructivo:
Entrada:
Sensibilidad:
1/4" (Tipo = +; Anillo = -; Mango = Masa)
55 kohmios
+17.5 dBu
0 dB
BASS CUT:
Conmutable:
Frecuencia de aplicación:
Encendido/ Apagado
80 Hz
12 dB/ Octavos.
BASS EQ:
Tipo:
Conmutable:
Frecuencia central:
Amplificación:
Descenso:
Filtro de campana
Encendido/ Apagado
ajustable de 20 Hz hasta 300 Hz
15 dB
6 dB/ Octavos.
15 dB
12 dB/ Octavos.
Tipo constructivo:
Salida:
Impedancia de salida:
Nivel de salida max.:
LINE OUT:
Tipo constructivo:
Salida:
Impedancia de salida:
Nivel de salida max.:
Amplificación:
Tipo:
Conmutable:
Frecuencia central:
Amplificación:
Descenso:
XLR (1 = Masa; 2 = +; 3 = -) y
yd 1/4" (Tipo = +; Anillo = -; Mango = Masa)
220 ohmios
+19 dBu
-∞ to +6 dB
BYPASS:
Conmutable:
Encendido / apagado
Consumo de corriente máx:
Consumo máx de potencia:
Fusible primario:
132 mA ( 172 mA con DI-MOD ) @ 240 Voltios AC
44 VA
T 1.25 A (lento)
Dimensión:
Ancho:
Alto:
Profundidad:
Peso:
482 mm (19")
44 mm (1 3/4")
238 mm (9 2/5")
3.44 kg (7 3/5 lbs.)
OPCIONES
DI-MOD USB:
DS 1-P:
MID EQ:
1/4" (Tipo = +; Anillo = -; Mango = Masa)
220 ohmios
+19 dBu
2 canales AD/DA, de hasta 24 Bit, 96 kHz
110 dB (a) volumen dinámico, USB IN/OUT,
además S/PDIF Out, Monitor estereo Out,
Expositor Plexiglás, mostrador ,
Dimensiones: 260 x 90 x 8 mm
Filtro de campana
Encendido/ Apagado
ajustable de 100 Hz hasta 11 kHz
15 dB
15 dB
3 dB/ Octavos - 24 dB/ Octavos. (ajustable,
Factor Q)
67
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 68
IMPORTANT SAFETY INSTRUCTIONS
WICHTIGE SICHERHEITSHINWEISE!
BEFORE CONNECTING, READ INSTRUCTIONS
BITTE VOR GEBRAUCH LESEN UND FÜR SPÄTEREN GEBRAUCH AUFBEWAHREN!
• Read all of these instructions!
• Das Gerät wurde von MindPrint ® gemäß IEC 60065 gebaut und hat das Werk in sicherheits-
• Save these instructions for later use!
technisch einwandfreiem Zustand verlassen. Um diesen Zustand zu erhalten und einen
• Follow all warnings and instructions marked on the product!
gefahrlosen Betrieb sicherzustellen, muss der Anwender die Hinweise und die Warnvermerke
• Do not use this product near water, i.e. bathtub, sink, swimming pool, wet basement, etc.
beachten, die in der Bedienungsanleitung enthalten sind. Das Gerät entspricht der Schutzklasse I (schutzgeerdet).
• Do not place this product on an unstable cart, stand or table. The product may fall, causing
• DIE SICHERHEIT, ZUVERLÄSSIGKEIT UND LEISTUNG DES GERÄTES WIRD VON
serious damage to the product or to persons!
MindPrint ® NUR DANN GEWÄHRLEISTET WENN:
• Slots and openings in the cabinet and the back or bottom are provided for ventilation; to
ensure reliable operation of the product and to protect it from overheating, these openings
• Montage, Erweiterung, Neueinstellung, Änderungen oder Reparaturen von MindPrint ® oder
von dazu ermächtigten Personen ausgeführt werden.
must not be blocked or covered. This product should not be placed in a built-in installation
• die elektrische Installation des betreffenden Raumes den Anforderungen von IEC (ANSI)-
unless proper ventilation is provided.
Festlegungen entspricht.
• This product should not be placed near a source of heat such as a stove, radiator, or
• das Gerät in Übereinstimmung mit der Gebrauchsanweisung verwendet wird.
another heat producing amplifier.
• Use only the supplied power supply or power cord. If you are not sure of the type of power
available, consult your dealer or local power company.
• Do not allow anything to rest on the power cord. Do not locate this product where persons
will walk on the cord.
• Never break off the ground pin on the power supply cord.
• Power supply cords should always be handled carefully. Periodically check cords for cuts or
sign of stress, especially at the plug and the point where the cord exits the unit.
• The power supply cord should be unplugged when the unit is to be unused for long periods
of time.
• If this product is to be mounted in an equipment rack, rear support should be provided.
• This product should be used only with a cart or stand that is recommended by MindPrint ®.
• Never push objects of any kind into this product through cabinet slots as they may touch
dangerous voltage points or short out parts that could result in risk of fire or electric shock.
Never spill liquid of any kind on the product.
• Do not attempt to service this product yourself, as opening or removing covers may expose
you to dangerous voltage points or other risks. Refer all servicing to qualified service
personnel.
• Unplug this product from the wall outlet and refer servicing to qualified service personnel
under the following conditions:
• When the power cord or plug is damaged or frayed.
• If liquid has been spilled into the product.
WARNUNG:
• Wenn Abdeckungen geöffnet oder Gehäuseteile entfernt werden, außer wenn dies von Hand
möglich ist, können Teile freigelegt werden, die Spannung führen.
• Wenn ein Öffnen des Gerätes erforderlich ist, muss das Gerät von allen Spannungsquellen
getrennt sein. Berücksichtigen Sie dies vor dem Abgleich, vor einer Wartung, vor einer
Instandsetzung und vor einem Austausch von Teilen.
• Ein Abgleich, eine Wartung oder eine Reparatur am geöffneten Gerät unter Spannung darf
nur durch eine vom Hersteller autorisierte Fachkraft (nach VBG 4) geschehen, die mit den
verbundenen Gefahren vertraut ist.
• Lautsprecher-Ausgänge, die mit dem IEC 417/5036-Zeichen (Abb.1, s.unten) versehen sind,
können berührungsgefährliche Spannungen führen. Deshalb vor dem Einschalten des Gerätes Verbindung nur mit dem vom Hersteller empfohlenen Anschlusskabel zum Lautsprecher
herstellen.
• Alle Stecker an Verbindungskabeln müssen mit dem Gehäuse verschraubt oder verriegelt
sein, sofern möglich.
• Es dürfen nur Sicherungen vom angegebenen Typ und der angegebenen Nennstromstärke als
Ersatz verwendet werden.
• Eine Verwendung von geflickten Sicherungen oder Kurzschließen des Halters ist unzulässig.
• Niemals die Schutzleiterverbindung unterbrechen.
• Oberflächen, die mit dem „HOT“-Zeichen (Abb.2, s.unten) versehen sind, Rückwände oder
Abdeckungen mit Kühlschlitzen, Kühlkörper und deren Abdeckungen sowie Röhren und
deren Abdeckungen können im Betrieb erhöhte Temperaturen annehmen und sollten deshalb
nicht berührt werden.
• Hohe Lautstärkepegel können dauernde Gehörschäden verursachen. Vermeiden Sie deshalb
die direkte Nähe von Lautsprechern, die mit hohen Pegeln betrieben werden. Verwenden Sie
einen Gehörschutz bei dauernder Einwirkung hoher Pegel.
• If the product has been exposed to rain or water.
• If the product does not operate normally when the operating instructions are followed.
• If the product has been dropped or the cabinet has been damaged.
• If the product exhibits a distinct change in performance, indicating a need of service!
• Adjust only these controls that are covered by the operating instructions since improper
adjustment of other controls may result in damage and will often require extensive work by
a qualified technician to restore the product to normal operation.
• Exposure to extremely high noise levels may cause a permanent hearing loss.
• Individuals vary considerably in susceptibility to noise induced hearig loss, but nearly
NETZANSCHLUSS:
•
•
•
•
Das Gerät ist für Dauerbetrieb ausgelegt.
Die eingestellte Betriebsspannung muß mit der örtlichen Netzspannung übereinstimmen.
Der Anschluss an das Stromnetz erfolgt mit dem mitgelieferten Netzteil oder Netzkabel.
Netzteil: Eine beschädigte Anschlussleitung kann nicht ersetzt werden. Das Netzteil darf
nicht mehr betrieben werden.
• Vermeiden Sie einen Anschluss an das Stromnetz in Verteilerdosen zusammen mit vielen
anderen Stromverbrauchern.
• Die Steckdose für die Stromversorgung muß nahe am Gerät angebracht und leicht
zugänglich sein.
everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time.
The U.S. Government´s Occupational Safety and Health Administration (OSHA) has specified
AUFSTELLUNGSORT:
the following permissible noise level exposures:
•
•
•
•
Duration Per Day In Hours
8
6
4
3
2
11/2
1
1
/2
1
/4 or less
Sound LeveldBA, Slow Response
90
92
95
97
100
102
105
110
115
• According to OSHA, any exposure in excess of the above permissible limits could result in
some hearing loss.
• Ear plug protectors in the ear canals or over the ears must be worn when operating this
amplification system in order to prevent a permanent hearing loss if exposure is in excess
of the limits as set forth above. To ensure against potentially dangerous exposure to high
sound pressure levels, it is recommended that all persons exposed to equipment capable of
producing high sound pressure levels such as this amplification system be protected by
hearing protectors while this unit is in operation.
• Fuses: Replace with IEC 127 (5x 20 mms) type and rated fuse for best performance only.
TO PREVENT THE RISK OF FIRE AND SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO
MOISTURE OR RAIN. DO NOT OPEN CASE; NO USER SERVICE-ABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
68
Das Gerät sollte nur auf einer sauberen, waagerechten Arbeitsfläche stehen.
Das Gerät darf während des Betriebs keinen Erschütterungen ausgesetzt sein.
Feuchtigkeit und Staub sind nach Möglichkeit fernzuhalten.
Das Gerät darf nicht in der Nähe von Wasser, Badewanne, Waschbecken, Küchenspüle, Nassraum, Swimmingpool oder feuchten Räumen betrieben werden. Keine mit Flüssigkeit gefüllten Gegenstände (Vase, Gläser, Flaschen etc.) auf das Gerät stellen.
• Sorgen Sie für ausreichende Belüftung der Geräte.
• Eventuelle Ventilationsöffnungen dürfen niemals blockiert oder abgedeckt werden. Das
Gerät muss mindestens 20 cm von Wänden entfernt aufgestellt werden. Das Gerät darf nur
dann in ein Rack eingebaut werden, wenn für ausreichende Ventilation gesorgt ist und die
Einbauanweisungen des Herstellers eingehalten werden.
• Vermeiden Sie direkte Sonneneinstrahlung sowie die unmittelbare Nähe von Heizkörpern
und Heizstrahlern oder ähnlicher Geräte.
• Wenn das Gerät plötzlich von einem kalten an einen warmen Ort gebracht wird, kann sich
im Geräteinnern Kondensfeuchtigkeit bilden. Dies ist insbesondere bei Röhrengeräten zu
beachten. Vor dem Einschalten solange warten bis das Gerät Raumtemperatur angenommen
hat.
• Zubehör: Das Gerät nicht auf einen instabilen Wagen, Ständer, Dreifuß, Untersatz oder Tisch
stellen. Wenn das Gerät herunterfällt kann es Personenschäden verursachen und selbst
beschädigt werden. Verwenden Sie das Gerät nur mit einem vom Hersteller empfohlenen
oder zusammen mit dem Gerät verkauften Wagen, Rack, Ständer, Dreifuß oder Untersatz. Bei
der Aufstellung des Gerätes müssen die Anweisungen des Herstellers befolgt und muss das
vom Hersteller empfohlene Aufstellzubehör verwendet werden. Eine Kombination aus Gerät
und Gestell muß vorsichtigt bewegt werden. Plötzliches Anhalten, übermäßige Kraftanwendung und ungleichmäßige Böden können das Umkippen der Kombination aus Gerät und
Gestell bewirken.
• Zusatzvorrichtungen: Verwenden Sie niemals Zusatzvorrichtungen, die nicht vom Hersteller
empfohlen wurden, weil dadurch Unfälle verursacht werden können
• Zum Schutz des Gerätes bei Gewitter oder wenn es längere Zeit nicht beaufsichtigt oder
benutzt wird, sollte der Netzstecker gezogen werden. Dies verhindert Schäden am Gerät
aufgrund von Blitzschlag und Spannungsstößen im Wechselstromnetz.
Abb.1
Abb.2
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 69
IMPORTANT ADVICE ON SAFETY!
CONSEILS DE SECURITE IMPORTANTS!
PLEASE READ BEFORE USE AND KEEP FOR LATER USE!
PRIERE DE LIRE AVANT L’EMPLOI ET A CONSERVER POUR UTILISATION ULTERIEURE!
• The unit has been built by MindPrint ® in accordance with IEC 60065 and left the factory in
safe working order. To maintain this condition and ensure non-risk operation, the user must
follow the advice and warning comments found in the operating instructions. The unit
conforms to Protection Class 1 (protectively earthed).
• MindPrint ® ONLY GUARANTEE THE SAFETY, RELIABILITY AND EFFICIENCY OF THE UNIT IF:
• Assembly, extension, re-adjustment, modifications or repairs are carried out by MindPrint ®
or by persons authorized to do so.
• The electrical installation of the relevant area complies with the requirements of IEC (ANSI)
specifications.
• The unit is used in accordance with the operating instructions.
• The unit is regularly checked and tested for electrical safety by a competent technician.
WARNING:
• If covers are opened or sections of casing are removed, except where this can be done
manually, live parts can become exposed.
• If it is necessary to open the unit this must be isolated from all power sources. Please take
this into account before carrying out adjustments, maintenance, repairs and before
replacing parts.
• Adjustment, maintenance and repairs carried out when the unit has been opened and is still
live may only be performed by specialist personnel who are authorized by the manufacturer
(in accordance with VBG 4) and who are aware of the associated hazards.
• Loudspeaker outputs which have the IEC 417/5036 symbol (Diagram 1, below) can carry
voltages which are hazardous if they are made contact with. Before the unit is switched on,
the loudspeaker should therefore only be connected using the lead recommended by the
manufacturer.
• Where possible, all plugs on connection cables must be screwed or locked onto the casing.
• Replace with IEC 127 (5x 20 mms) type and rated fuse for best performance only.
• It is not permitted to use repaired fuses or to short-circuit the fuse holder.
• Never interrupt the protective conductor connection.
• Surfaces which are equipped with the „HOT“ mark (Diagram 2, below), rear panels or
covers with cooling slits, cooling bodies and their covers, as well as tubes and their covers
are purposely designed to dissipate high temperatures and should therefore not be touched.
• High loudspeaker levels can cause permanent hearing damage. You should therefore avoid
the direct vicinity of loudspeakers operating at high levels. Wear hearing protection if
continuously exposed to high levels.
MAINS CONNECTION:
• L’appareil a été conçu par MindPrint ® selon la norme IEC 60065 et a quitté l’entreprise dans
un état irréprochable. Afin de conserver cet état et d’assurer un fonctionnement sans
danger de l’appareil nous conseillons à l’utilisateur la lecture des indications de sécurité
contenues dans le mode d’emploi. L’appareil est conforme à la classification I (mise à terre
de protection).
• SURETE, FIABILITE ET EFFICACITE DE L’APPAREIL NE SONT GARANTIS PAR MindPrint ® QUE SI:
• Montage, extension, nouveau réglage, modification ou réparation sont effectués par MindPrint ® ou par toute personne autorisée par MindPrint ®.
• L’installation électrique de la pièce concernée correspond aux normes IEC (ANSI).
• L’utilisation de l’appareil suit le mode d’emploi.
AVERTISSEMENT:
• A moins que cela ne soit manuellement possible, tout enlèvement ou ouverture du boîtier
peut entrainer la mise au jour de pieces sous tension.
• Si l’ouverture de l’appareil est nécessaire, celui-ci doit être coupé de chaque source de
courant. Ceci est à prendre en considération avant tout ajustement, entretien, réparation ou
changement de pieces.
• Ajustement, entretien ou réparation sur l’appareil ouvert et sous tension ne peuvent être
éffectués que par un spécialiste autorisé par le fabricant (selon VBG4). Le spécialiste étant
conscient des dangers liés à ce genre de réparation.
• Les sorties de baffles qui portent le signe IEC 417/5036 (fig. 1, voir en bas) peuvent être
sous tension dangereuse. Avant de brancher l’appareil utiliser uniquement le câble de
raccordement conseillé par le fabricant pour raccorder les baffles.
• Toutes les prises des câbles de raccordement doivent être, si possible, vissées ou
verrouillées sur le boîtier.
• Utilisez subsidiairement uniquement des fusibles de type et de puissance de courant
nominale donnés.
• L’utilisation de fusibles rafistolés ou court-circuites est inadmissible.
• Ne jamais interrompre la connexion du circuit protecteur.
• Il est conseillé de ne pas toucher aux surfaces pourvues du signe „HOT“ (fig. 2, voir en
bas), aux parois arrières ou caches munis de fentes d’aération, éléments d’aération et leurs
caches ansi qu’aux tubes et leurs caches. Ces éléments pouvant atteindre des températures
élévées pendant l’utilisation de l’appareil.
• Les Niveaux de puissance élévés peuvent entrainer des lésions auditives durables. Evitez
donc la proximité de haut-parleurs utilisés à haute puissance. Lors de haute puissance
continue utilisez une protection auditive.
•
•
•
•
The unit is designed for continuous operation.
The set operating voltage must match the local mains supply voltage.
The unit is connected to the mains via the supplied power unit or power cable.
Power unit: Never use a damaged connection lead. Any damage must be rectified by a
competent technician.
• Avoid connection to the mains supply in distributor boxes together with several other
power consumers.
• The plug socket for the power supply must be positioned near the unit and must be easily
accessible.
BRANCHEMENT SUR LE SECTEUR:
PLACE OF INSTALLATION:
LIEU D’INSTALLATION:
•
•
•
•
•
•
•
•
The unit should stand only on a clean, horizontal working surface.
The unit must not be exposed to vibrations during operation.
Keep away from moisture and dust where possible.
Do not place the unit near water, baths, wash basins, kitchen sinks, wet areas, swimming
pools or damp rooms. Do not place objects containing liquid on the unit - vases, glasses,
bottles etc.
• Ensure that the unit is well ventilated.
• Any ventilation openings must never be blocked or covered. The unit must be positioned at
least 20 cm away from walls. The unit may only be fitted in a rack if adequate ventilation is
ensured and if the manufacturer’s installation instructions are followed.
• Keep away from direct sunlight and the immediate vicinity of heating elements and radiant
heaters or similar devices.
• If the unit is suddenly moved from a cold to a warm location, condensation can form inside
it. This must be taken into account particularly in the case of tube units. Before switching
on, wait until the unit has reached room temperature.
• Accessories: Do not place the unit on an unsteady trolley, stand, tripod, base or table. If the
unit falls down, it can cause personal injury and itself become damaged. Use the unit only
with the trolley, rack stand, tripod or base recommended by the manufacturer or purchased
together with the unit. When setting the unit up, all the manufacturer’s instructions must be
followed and the setup accessories recommended by the manufacturer must be used. Any
combination of unit and stand must be moved carefully. A sudden stop, excessive use of
force and uneven floors can cause the combination of unit and stand to tip over.
• Additional equipment: Never use additional equipment which has not been recommended
by the manufacturer as this can cause accidents.
• To protect the unit during bad weather or when left unattended for prolonged periods, the
mains plug should be disconnected. This prevents the unit being damaged by lightning and
power surges in the AC mains supply.
Diagram 1
• L’appareil est conçu pour une utilisation continue.
• La tension de fonctionnement doit concorder avec la tension secteur locale.
• Le raccordement au réseau éléctrique s’effectue avec l’adaptateur ou le cordon
d´alimentation livré avec l’appareil.
• Adaptateur: Un câble de raccordement abimé ne peut être remplacé. L’adaptateur est
inutilisable.
• Evitez un raccordement au réseau par des boîtes de distribution surchargées.
• La prise de courant doit être placée à proximité de l’appareil et facile à atteindre.
L’appareil doit être placé sur une surface de travail propre et horizontale.
L’appareil en marche ne doit en aucun cas subir des vibrations.
Evitez dans la mesure du possible poussière et humidité.
L’appareil ne doit pas être placé à proximité d’eau, de baignoire, lavabo, évier, pièce d’eau,
piscine ou dans une pièce humide. Ne placez aucun vase, verre, bouteille ou tout objet
rempli de liquide sur l’appareil.
• L’appareil doit être suffisamment aéré.
• Ne jamais recouvrir les ouvertures d’aération. L’appareil doit être placé à 20 cm du mur au
minimum. L’appareil peut être monté dans un Rack si une ventilation suffisante est possible
et si les conseils de montage du fabricant sont suivis.
• Evitez les rayons de soleil et la proximité de radiateurs, chauffages etc.
• Une condensation d’eau peut se former dans l’appareil si celui-ci est transporté
brusquement d’un endroit froid à un endroit chaud. Ceci est particulièrement important
pour des appareils à tubes. Avant de brancher l’appareil attendre qu’il ait la température
ambiante.
• Accessoires: L’appareil ne doit être placé sur un chariot, support, trépied, bâti ou table
instable. Une chute de l’appareil peut entrainer aussi bien des dommages corporels que
techniques. Utilisez l’appareil uniquement avec un chariot, Rack, support, trépied ou bâti
conseillé par le fabricant ou vendu en combinaison avec l’appareil. Les indications du
fabricant pour l’installation de l’appareil sont à suivre, et les accessoires d’installation
conseillés par le fabricant sont à utiliser. Un ensemble support et appareil doit être déplacé
avec précaution. Des mouvements brusques et des revêtements de sol irreguliers peuvent
entrainer la chute de l´ensemble.
• Equipements supplémentaires: Ne jamais utiliser un équipement supplémentaire n’ayant pas
été conseillé par le fabricant, ceci pouvant entrainer des accidents.
• Afin de protéger l’appareil pendant un orage ou s’il ne doit pas être utilisé pendant un
certain temps, il est conseillé d’enlever la prise au secteur. Ceci évite des dommages dûs à
la foudre ou à des coups de tension dans le réseau à courant alternatif.
Diagram 2
Fig. 1
Fig. 2
69
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 70
IMPORTANTI AVVERTIMENTI DI SICUREZZA!
¡INDICACIONES DE SEGURIDAD IMPORTANTES!
Leggere attentamente prima dell’uso e conservare per un utilizzo successivo:
¡LÉANSE ANTES DE UTILIZAR EL APARATO Y GUARDENSE PARA SU USO POSTERIOR!
®
• L’apparecchio è stato costruito dalla MindPrint secondo la normativa europea IEC 60065
ed ha lasciato il nostro stabilimento in stato ineccepibile. Per garantire il mantenimento di
tale stato e un utilizzo assolutamente privo di rischi l’utente è tenuto ad osservare le indicazioni e gli avvertimenti di sicurezza contenuti nelle istruzioni per l’uso. L’apparecchio
rispecchia il livello di sicurezza I (collegato a terra).
• Sicurezza, affidabilità e prestazioni dell’apparecchio vengono garantiti dalla MindPrint ® solo
ed esclusivamente se:
• Montaggio, ampliamento, rimessa a punto, modifiche e riparazioni vengono eseguite dalla
MindPrint ® stessa o da personale da essa autorizzato.
• Gli impianti elettrici nei locali prescelti per l’uso dell’apparecchio rispondono alle normative
stabilite dall’ANSI.
• L’apparecchio viene utilizzato come indicato nel libretto delle istruzioni per l’uso.
Avvertimenti:
• In caso di apertura di parti di rivestimento o rimozione di parti dell’involucro, a meno che
non si tratti di pezzi rimovibili semplicemente a mano, possono venire alla luce parti
dell’apparecchio conduttrici di tensione.
• Se l’apertura dell’apparecchio dovesse risultare necessaria è indispensabile staccare
precedentemente quest’ultimo da tutte le fonti di tensione. Rispettare tale misura di
prevenzione anche prima di un allineamento, di operazioni di manutenzione, della messa in
esercizio o della sostituzione di componenti all’interno dell’apparecchio.
• Allineamento, operazioni di manutenzione o eventuali riparazioni dell’apparecchio in presenza di tensione vanno eseguite esclusivamente da personale specializzato ed autorizzato,
in grado di eseguire tali operazioni evitandone i rischi connessi.
• Le uscite degli altoparlanti contrassegnate dai caratteri IEC 417/5036 (vedi illustrazione 1 a
fondo pag.) possono essere conduttrici di tensione pericolosa con cui evitare il contatto. Per
questo motivo, prima di accendere l’apparecchio, collegare quest’ultimo agli altoparlanti
servendosi esclusivamente del cavetto d’allacciamento indicato dal produttore.
• Tutte le spine e i cavi di collegamento devono essere avvitati o fissati all’involucro
dell’apparecchio per quanto possibile.
• Tutti i fusibili di sicurezza vanno sostituiti esclusivamente con fusibili del tipo prescritto e
valore della corrente nominale indicato.
• L’utilizzo di fusibili di sicurezza non integri e la messa in corto circuito del sostegno di
metallo sono proibite.
• Non interrompere mai il collegamento con il circuito di protezione.
• Superfici contrassegnate dalla parola „HOT“ (vedi illustrazione 2 a fondo pag.), cosi come
griglie di aerazione, dispositivi di raffreddamento e i loro rivestimenti di protezione, oppure
valvole e i relativi rivestimenti protettivi possono surriscaldarsi notevolmente durante l’uso
e per questo motivo non vanno toccate.
• L’ascolto di suoni ad alto volume può provocare danni permanenti all’udito. Evitate perciò
la diretta vicinanza con altoparlanti ad alta emissione di suono e utilizzate cuffie protettive
in caso ciò non sia possibile.
Alimentazione:
• L’apparecchio è concepito per il funzionamento continuo.
• La tensione di esercizio deve corrispondere alla tensione di rete a cui ci si allaccia.
• L’allacciamento alla rete elettrica avviene tramite alimentatore o cavetto d’alimentazione
consegnato insieme all’apparecchio.
• Alimentatore: un cavo di connessione danneggiato non può essere sostituito. L’alimentatore
non può più essere utilizzato.
• Evitate un allacciamento alla rete di corrente utilizzando cassette di distribuzione
sovraccariche.
• La spina di corrente deve essere situata nelle vicinanze dell’apparecchio e facilmente
raggiungibile in qualsiasi momento.
Locali di collocamento:
•
•
•
•
Opportuno collocare l’apparecchio su una superficie pulita e orizzontale.
Non sottoporre l’apparecchio in funzione a scosse e vibrazioni.
Proteggere l’apparecchio per quanto possibile da umidità e polvere.
Non collocare l’apparecchio vicino ad acqua, vasche da bagno, lavandini, lavelli da cucina,
locali umidi o piscine. Non appoggiare recipienti contenenti liquidi - vasi, bicchieri,
bottiglie, ecc. - sull’apparecchio.
• Provvedere ad una buone aerazione dell’apparecchio.
• Eventuali aperture previste per la ventilazione dell’apparecchio non vanno ne bloccate, ne
mai coperte. L’apparecchio va collocato ad almeno 20 cm di distanza dalle pareti circostanti
e può essere inserito tra altre componenti di un impianto solo in caso di sufficiente
ventilazione e qualora le direttive di montaggio del produttore vengano rispettate.
• Evitare di esporre l’apparecchio ai raggi del sole e di collocarlo direttamente nelle vicinanze
di fonti di calore come caloriferi, stufette, ecc.
• Se l’apparecchio viene trasportato rapidamente da un locale freddo ad uno riscaldato può
succedere che al suo interno si crei della condensa. Ciò va tenuto in considerazione
soprattutto in caso di apparecchi a valvole. Attendere che l’apparecchio abbia assunto la
temperatura ambiente prima di accenderlo.
• Accessori: non collocare l’apparecchio su carrelli, supporti, treppiedi, superfici o tavoli
instabili. Se l’apparecchio dovesse cadere a terra potrebbe causare danni a terzi o
danneggiarsi irreparabilmente. Utilizzate per il collocamento dell’apparecchio supporti,
treppiedi e superfici che siano consigliate dal produttore o direttamente comprese
nell’offerta di vendita. Per il collocamento dell’apparecchio attenetevi strettamente alle
istruzioni del produttore, utilizzando esclusivamente accessori da esso consigliati. L’apparecchio in combinazione ad un supporto va spostato con molta attenzione. Movimenti bruschi o il collocamento su pavimenti non piani possono provocare la caduta dell’apparecchio
e del suo supporto.
• Accessori supplementari: non utilizzate mai accessori supplementari che non siano
consigliati dal produttore, potendo essere ciò causa di incidenti.
• Per proteggere l’apparecchio in caso di temporali o nel caso questo non venisse utilizzato
per diverso tempo si consiglia di staccarne la spina di corrente. In questo modo si evitano
danni all’apparecchio dovuti a colpi di fulmine o ad improvvisi aumenti di tensione nel
circuito di corrente alternata.
Illustrazione 1
70
Illustrazione 2
• El aparato ha sido producido por MindPrint ® según el IEC 60065 y salió de la fábrica en un
estado técnicamente perfecto. Para conservar este estado y asegurar un funcionamiento sin
peligros el usuario debe tener en cuenta las indicaciones y advertencias contenidas en las
instrucciones de manejo. El aparato corresponde a la clase de protección l (toma de tierra
protegida).
• LA SEGURIDAD, LA FIABILIDAD Y EL RENDIMIENTO DEL APARATO SOLO ESTAN
GARANTIZADOS POR MindPrint ® CUANDO:
• el montaje, la ampliación, el reajuste, los cambios o las reparaciones se realicen por
MindPrint ® o por personas autorizadas para ello;
• la instalación eléctrica del recinto en cuestión corresponda a los requisitos de la
determinación del IEC (ANSI);
• el aparato se use de acuerdo con las indicaciones de uso.
ADVERTENCIA:
• Si se destapan protecciones o se retiran piezas de la carcasa, exceptuando si se puede
hacer manualmente, se pueden dejar piezas al descubierto que sean conductoras de
tensión.
• Si es necesario abrir el aparato, éste tiene que estar aislado de todas las fuentes de
alimentación. Esto se debe tener en cuenta antes del ajuste, de un entretenimiento, de una
reparación y de una sustitución de las piezas.
• Un ajuste, un entretenimiento o una reparación en el aparato abierto y bajo tensión sólo
puede ser llevado a cabo por un especialista autorizado por el productor (según VBG 4) que
conozca a fondo los peligros que ello conlleva.
• Las salidas de altavoces que estén provistas de la característica IEC 417/5036 (figura 1,
véase abajo) pueden conducir tensiones peligrosas al contacto. Por ello es indispensable
que antes de poner en marcha el aparato; la conexión se haya realizado únicamente con el
cable de empalmes recomendado por el productor.
• Las clavijas de contacto al final de los cables conectores tienen que estar atornilladas o
enclavadas a la carcasa, en tanto que sea posible.
• Los fusibles de repuesto que se utilicen sólo pueden ser del tipo indicado y tener la
intensidad nominal indicada.
• El uso de fusibles reparados o la puesta en cortocircuito del soporte es inadmisible.
• El empalme del conductor de protección no se puede interrumpir en ningún caso.
• Las superficies provistas de la característica "HOT" (figura 2, véase abajo), los paneles de
fondo trasero o las protecciones con ranuras de ventilación, los cuerpos de ventilación y sus
protecciones, así como las válvulas electrónicas y sus protecciones pueden alcanzar
temperaturas muy altas durante el funcionamiento y por ello no se deberían tocar.
• Niveles elevados de la intensidad de sonido pueden causar continuos daños auditivos; por
ello debe evitar acercarse demasiado a altavoces que funcionen a altos niveles. En tales
casos utilice protecciones auditivas.
ACOMETIDA A LA RED:
• El aparato está proyectado para un funcionamiento continuo.
• La tensión de funcionamiento ajustada tiene que coincidir con la tensión de la red del lugar.
• La conexión a la red eléctrica se efectuará con la fuente de alimentación o con el cable de
red que se entreguen con el aparato.
• Fuente de alimentación: una linea de conexión dañada no se puede sustituir. La fuente de
alimentación no puede volver a ponerse en funcionamiento.
• Evite una conexión de la red eléctrica a distribuidores con muchas tomas de corriente.
• El enchufe para el suministro de corriente tiene que estar cerca del aparato y ser de fácil
acceso.
SITUACION:
•
•
•
•
El aparato debería estar situado en una superficie limpia y totalmente horizontal.
El aparato no puede estar expuesto a ningún tipo de sacudidas durante su funcionamiento.
Se deben evitar la humedad y el polvo.
El aparato no puede ponerse en funcionamiento cerca del agua, la bañera, el lavamanos, la
pila de la cocina, un recinto con tuberías de agua, la piscina o en habitaciones húmedas.
Tampoco se pueden poner objetos llenos de líquido - jarrones, vasos, botellas, etc. - encima
de él.
• Procure que el aparato tenga suficiente ventilación.
• Las aberturas de ventilación existentes no se deben bloquear ni tapar nunca. El aparato
debe estar situado como mínimo a 20 cm de la pared. El aparato sólo se puede montar en
un rack, si se ha procurado la suficiente ventilación y se han cumplido las indicaciones de
montaje del productor.
• Evite los rayos del sol directos así como la proximidad a radiadores, electro-radiadores o
aparatos similares.
• Si el aparato pasa repentinamente de un lugar frío a otro caliente, se puede condensar
humedad en su interior. Esto se debe tener en cuenta sobretodo en los aparatos con
válvulas electrónicas. Antes de poner en marcha el aparato se debe esperar hasta que éste
haya adquirido la temperatura ambiental.
• Accesorios: el aparato no se puede colocar encima de carros, estantes, trípodes, soportes o
mesas inestables. Si el aparato se cae puede causar daños personales y se puede estropear.
Coloque el aparato sólo en un carro, rack, estante, trípode o soporte recomendado por el
productor o que se le haya vendido junto con el aparato. En la instalación se deben seguir
las indicaciones del productor así como utilizar los accesorios recomendados por el mismo
para colocarlo encima. El conjunto del aparato con el pedestal se debe mover con mucho
cuidado. Un paro brusco, la aplicación de una fuerza desmesurada o un suelo irregular
puede ocasionar la caida de todo el conjunto.
• Piezas adicionales: no utilice nunca piezas adicionales que no estén recomendadas por el
productor, ya que se podrían provocar accidentes.
• Para protejer el aparato de una tormenta o si no se supervisa ni utiliza durante algún
tiempo, se debería desconectar la clavija de la red. Así se evitan daños en el aparato a
causa de un rayo y golpes de tensión en la red de corriente alterna.
Figura 1
Figura 2
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 71
This is to certify that
Für das folgend bezeichnete Erzeugnis
EN-VOICE ® MK II
EN-VOICE ® MK II
complies with the provisions of the Directive of the Council of the European
Communities on the approximation of the laws of the Member States
relating to electromagnetic compatibility (EMC Directive 89/336/EEC) and
the low voltage Directive (73/23/EEC).
This declaration of conformity of the European Communities is the result
of an examination carried out by the Quality Assurance Department of
STAMER GmbH in accordance with European Standards EN 50081-1,
EN 50082-1and EN 60065 for low voltage, as laid down in Article 10 of
the EMC Directive.
wird hiermit bestätigt, dass es den wesentlichen Schutzanforderungen
entspricht, die in der Richtlinie des Rates zur Angleichung der Rechtsvorschriften der Mitgliedsstaaten über die elektromagnetische Verträglichkeit (89/336/EWG) und der Niederspannungsrichtlinie (73/23/EWG)
festgelegt sind. Diese Erklärung gilt für alle Exemplare und bestätigt die
Ergebnisse der Messungen, die durch die Qualitätssicherung der Fa. Stamer
Musikanlagen GmbH durchgeführt wurden. Zur Beurteilung des Erzeugnisses
hinsichtlich elektromagnetischer Verträglichkeit wurden folgende Normen
herangezogen: EN 50081-1 • EN 50082-1.
Zur Beurteilung der Einhaltung der Niederspannungsrichtlinie wurde folgende
Norm herangezogen: EN 60065
Stamer Musikanlagen GmbH*
Magdeburger Str. 8
66606 St.Wendel
Diese Erklärung wird verantwortlich für den Hersteller
Stamer Musikanlagen GmbH*
Magdeburger Str. 8
66606 St.Wendel
abgegeben durch
Lothar Stamer Dipl.Ing.
Managing Director
St.Wendel, 09/25/03
* Stamer Musikanlagen manufactures exclusively for MindPrint.
Lothar Stamer Dipl.Ing.
Geschäftsführer
St.Wendel, den 25/09/03
* Stamer Musikanlagen stellt exklusiv für MindPrint her.
71
EnVoice_Manual_1.1
15.10.2003
9:15 Uhr
Seite 72
MindPrint-DTC TM
MS D-0900 010/03
m
.
w
ww
m
o
c
.
t
n
i
r
indp
MUSIC & SALES GmbH • Postfach 1509 • 66595 St. Wendel
Tel. 0 68 51 - 90 50 • Fax 0 68 51 - 90 51 00
E-mail: info@mindprint.com

Manual - Mindprint

Transcription

Similar documents

EF1000-3000

Cylindrical GEM Inner Tracker for BESIII

Fara Tech Spec - Active Events

Miniature audio cables

OFFICIAL WARWICK AMP OWNER MANUAL

o-tone music Technical Rider

349 025 300 113 Chevrolet Captiva, 06/2006 – 2013

JK Audio