Essemtec Pantera X-plus SMT pick and place system flyer

HI GHLY F LE X I B LE S MD P L AC EM EN T SY ST EM FOR SM ALL AN D M EDI UM E NTE RP RI SE S
Highly flexible SMT placement
machine for your production
 Placement speed: 4‘500 cph*
 Component range: 0201 to 45x45 mm
 Intelligent single feeders, setup with bar code reader
 Feeder capacity 115 x 8 mm
 Intelligent tape feeder 8 to 56 mm
 Pantera XV-plus - Vision system for component inspection
 Optical alignment „on the fly“
 Absolute linear measuring systems
 Placer - Easy graphical operating software
with unique „virtual view“ function
*max. placement speed
Large feeder capacity
Large feeder capacity and automatic identification of the intelligent
feeders minimize changeover time. All tape feeders are electrically
driven and feeding pitch is programmable. Feeders are compact and of
light construction.
Easy to operate
The operating software Placer is the key to flexibility. The powerful
software is based on Windows8.1 with a graphical surface.
Time saving changeovers
The Pantera X-plus can be programmed o�-line or on-line. Bar codes on
feeders and components guarantee a flawless and fast programming.
Space saving
With a footprint of less than 1 sqm this machine fits in every production.
Essemtec Switzerland
Mosenstrasse 20
6287 Aesch, Lu
Phone: +41 (0)41 919 60 60
Email: info@essemtec.com
Process specifications
Productivity
Feeder
Components
Accuracy
PCB
Dimensions
Supplies
Pantera V-plus Pantera XV-plus
Pantera XVC-plus
Max. placement speed / cycle 1‘250 cph
time
4‘500 cph / 0.8 s
Speed according IPC9850
1‘120 cph
3‘400 cph
Changeover standstill time
< 1 minute
Feeder capacity 8 mm tape
108
Feeder type
Type CSM, programmable, intelligent single feeders (CSM)
Component size range
0402 - 45x45 mm or 0201 - 45x45 mm**
Min. lead pitch
0.5 mm (20 mil) or 0.4 mm (16 mil)**
Min. component height
0.25 mm
Max. component height
10 mm (15 mm*)
Linear encoder resolution
1 µm (x,y)
Rotation axis resolution
0.01°
Placement accuracy (x, y)
80 µm @ 3σ
Min. PCB dimensions
25x25 mm (1x1‘‘)
50x50 mm (2x2‘‘)
Max. PCB dimensions
405x335 mm (15.9 x 13.2 ‘‘)
535x290 mm (21.1 x 11.4‘‘)
PCB thickness
0.5 - 3.5 mm (0.02 - 0.13‘‘)
Clearance below PCB
40 mm (1.57")
Machine footprint
93.5 x 93.5 cm (36.8 x 36.8")
Operating floor space
200 x 195 cm (78.7 x 76.8")
Machine height
147 cm (57.9”) ; with Signal tower 205 cm (80.7")
Machine weight
250 kg (551 lb)
Electrical
230V / 50Hz or 110V / 60Hz
Power consumption
1 kW
Compressed air
5-7 bar, clean and filtered, not condensed, ISO 8573-1: class 3 (max. part
diameter 5 µm, dew point <-20°C, oil <= 1 mg/m3)
Air consumption
Max. 40 NLtr. / Min.
Air connection diameter
8 mm diameter
* optional or on request
** with option PANX-VIS-0201
*** larger dimensions on request
February 2015, Concept: MoS, Text: MoS, Layout: ErD, © by Essemtec
57
SWISS MADE
The PANTERA X-plus – SMD
placer for flexible production
 Ideal for high-mix / low volume production
 One machine for all SMT tasks
 Optional: Integrated dispensing system
 Vision system for component inspection
 Placer - Easy graphical operating software with
unique „virtual view“ function
 Max. throughput up to 4500 cph
 Optical alignment „on-the-fly“
 Feeder capacity 115 x 8 mm (tape feeder 8-56 mm)
 Intelligent feeder setup with bar code reader
 Component range: 0201 to 50x50 mm
 Absolute linear measuring systems
 Large application range
2
SWISS MADE
Demands on a highly flexible
SMT production environment
Fast product changeover and small series
characterize modern SMT production. In
order to fulfill customer demands, a short
changeover time is the most important
feature. Therefore, large feeder capacity,
automatic feeder identification and a
simple user interface are important
characteristics of this high-flexible
placement machine. The variety of feeders
opens up a large application spectrum and
provides flexibility. Tape reels, single tape
segments, bars and pallets of various sizes
can be used for component feeding. The
combination of a placement system with a
dispenser saves costs and space for
additional machines. The Pantera X-plus
series features an ideal price/performance
ratio for SME (Small and Medium
Enterprises).
3
A D D E D VA LU E
SMD placement machine with large
feeder capacity and offline programming
For a high-mix production, changeover time is the most important cost factor. The Pantera
X-plus concept reduces changeover time and costs to a minimum. Offline programming, in
combination with intelligent feeders and large feeder capacity, facilitate an economical
low-volume placement. All feeders for belts and bars are intelligent. Their positions in the
placement machine are recognized automatically. The feeders‘ status is shown in colours
on the screen.
The Pantera X-plus has capacity for more than 115 components. That‘s why many standard
components (e.g. resistors, capacitors) can permanently remain in the machine, only
specific components must then be updated. Offline programming allows for preparation of
subsequent orders without stopping the placement machine during production.
4
»
With its user-friendly offline-programming subsequent
jobs can be prepared while the production is running.
The machine doesn‘t need to be stopped for any kind of
product changeover.
Easy operation
The operating software „Placer“ is the key to flexibility. The powerful software is based on
Windows 8.1 with a graphical user interface.
Large capacity
The large feeder capacity and automatic identification of intelligent feeders minimize
changeover time. All tape feeders are electrically driven and feeding pitch is
programmable.
Space saving
With a footprint of only 92X92 cm (36.2x36.2“) this machine fits in every production line.
A CC U R A C Y
High speed and accuracy
The Pantera XV-plus is equipped with three optical systems, a laser alignment, a top-down
and a bottom-up vision. The combination of all these facilitates fast placement of discrete
components and precise placing of fine-pitch and BGA using one machine.
Top-down Vision
Locates fiducial marks automatically. It can
be used for teaching and controlling after
dispensing and placement.
Bottom-up Vision
Examines all expensive QFP and BGA
before placement (only Pantera XV-plus). It
measures all component connections
and tests dimensions and numbers.
Laser alignment
Laser alignment (Cyberoptics ©) fast and
precisely measures all components on
their way from feeder to placement
location (on-the-fly).
5
S O F T WA R E
Easy operation and programming
with a clear interface
„Placer“ is the powerful user interface of the Pantera X-plus. All information is represented
graphically. Complex placement data is shown in an easily understandable way as a
virtual PCB. The universal PANX-CAD interface converts data from layout programs (CAD)
into placement files within seconds. The Pantera X-plus ships with an extensive
component library. Additional components can fast and easily be created using the
installed „wizard“. Program changes are possible with one mouse click. For instance
rotating, mirroring, moving and erasing of components. Multiple panels can be generated
out of a single PCB. The unique „virtual-view function“ allows test and correction of a
program without placing a component. With the software „Placer“ users always have
control over the machine‘s status, the feeders and the components.
6
»
With the software „Placer“ users always have control
over the machines‘ status, the feeders and the components. The software is continuously updated and
improved in cooperation with our customers.
FLEXIBILIT Y
Integrated dispenser for adhesives and solder paste
The Pantera X-plus can be ordered optionally with a screw or time-pressure dispensing
valve for metered adhesive spots or solder paste. The valve is mounted on the back of the
placement head.
For dispensing no additional programming is necessary. The coordinates of the adhesive or
solder paste points are stored in the component library. This combination, a placement
system with a dispensing system saves costs and space for additional equipment.
A wide range of feeding systems for various applications
A flexible production meets the needs of customers. Therefore, the Pantera X-plus is fully
configurable with regards to feeders and components. Free space, which is not occupied by
the PCB, belts or sticks can be used by pallets or rest-tape feeders. The software also
accepts customer specific designs as feeders. For all belts and sticks standard feeders are
available. Belts from 8 to 56 mm width can be processed. Components can be up to 15 mm
high. For pallets and tape segments universal feeders are available.
7
CO N TA C T U S
Essemtec AG
Mosenstrasse 20
CH-6287 Aesch/LU
Switzerland
Phone: +41 (0)41 919 60 60
Fax: +41 (0)41 919 60 50
info@essemtec.com
For a complete list of all representatives and more product
information please visit our website:
www.essemtec.com
Become a fan:
Your local Essemtec partner:
Disclaimer:
The information contained in this brochure is for general information purposes only.
The information is provided by Essemtec and whilst we endeavour to keep the
information up-to-date and correct, we make no representations or warranties of any
kind, express or implied, about the completeness, accuracy, reliability, suitability.
Essemtec reserves the right to alter any product or service. Aesch, May 2014
Copyright Information:
All materials contained in this brochure are copyright © Essemtec AG,
Switzerland. This information is issued to provide outline information
only. Use, application or reproduction for any purpose or formation of
any order or contract is prohibited unless agreed by Essemtec.
Concept: ErD Text: MoS Layout: ErD