Polarized Filter Set for your Microscope for under

Transcription

Polarized Filter Set for your Microscope for under $75.00
***Every Gemological Microscope should have a Polarized Filter Set Attachment!!!***
What you will need:
2 – 55mm Polarized Filters
1 – Pack of Self-Adhesive Velcro Strips 1-Inch Wide x 3-Inches Long
You can go to Best Buy or a camera store and purchase Two (2) 55mm Camera Lens Polarizing Filters
Your cost $15.00 to $30.00 Each.
You can go to Office Depot or Office Max and purchase a small pack of 1-Inch Wide x 3-Inches Long of
Self-Adhesive Velcro Strips.
Estimated Time of Assembly:
10 to 15 Minutes
Just follow the simple instructions or the photographs. It is that easy!!!
#1. First pull the Velcro strips apart and use the harder Nylon Hook strip.
#2. Cut a 1-Inch wide by approximately ½-Inch to ¾-Inch long piece of the Harder Nylon Hooked part of
the Velcro strip. Cut Two (2) pieces same wide & length.
#3. Remove the self-adhesive backing and mount the strip on each side of your microscope Optical head
near the bottom of the head closest to the objective lens.
La Shawn Bauer, GG & High Sierra Gem Lab
© October 2011
Email: HighSierraGemLab@gmail.com
Page 1 of 23
Notice the White Velcro Backing near the bottom of the Optical Head
Apply Stiff Nylon Hook Part of Velcro on both sides of the Optical Head
© October 2011
Page 2 of 23
Close-Up View of the Stiff Nylon Hook part of the Velcro attached to the Optical Head
© October 2011
Page 3 of 23
Apply Stiff Nylon Hook part of Velcro
backing on opposite side of the
Polarizing Filter as show in the photo
The Fussy Soft part of the Velcro is
then attached to the Stiff Nylon Hook
portion of the Velcro of the Polarizing
Filter as seen in the photo
***SPECIAL NOTE***
DO NOT REMOVE ADHESIVE BACKING
on the Soft Fuzzy portion of the Velcro
strips.
Notice both sides are fixed and the
Velcro Soft / Fuzzy Strips are attached
to the Polarizing Filter
***SPECIAL NOTE***
DO NOT REMOVE ADHESIVE BACKING
on the Soft Fuzzy portion of the Velcro
strips.
© October 2011
Page 4 of 23
Notice that One (1) Side of the Filter is now attached to the Optical Head of the Microscope
© October 2011
Page 5 of 23
Notice the Polarizing Filter is just about to be attached to the opposite side of the microscope with the
Velcro strip
© October 2011
Page 6 of 23
Notice that the Polarizing Filter is now correctly attached to the optical head of the microscope
You are more than halfway finish with this simple easy project
© October 2011
Page 7 of 23
Place the Second Polarizing Filter over the Light Well of Your Microscope as seen in photo
You will want to make sure your microscope is vertical in the full and up-right position
© October 2011
Page 8 of 23
This is a photo of my Older Mark V Bausch & Lomb Gemolite Microscope set up
© October 2011
Page 9 of 23
Once again MY Old Trusty Gemolite Mark V B&L Microscope
© October 2011
Page 10 of 23
***SPECIAL NOTE***
If you want you can also use the extra Velcro and you can attach the bottom filter in place so you can tilt
and use your microscope at various angles of tilt if you want.
***SPECIAL Operational Notes****
NEVER USE THE Focus Knob on the Microscope when trying to view the strain pattern in a diamond
It is easier to tilt & turn your microscope mounted tweezers
You will be wasting time and chasing your tail if you constantly try to refocus your microscope using the
focusing knob when looking at and viewing strain within the diamond.
Not until you get use to how to find and observe the strain pattern then you can fine turn the focus
using the main focusing knob on the microscope especially if you are taking photomicrographs then
small adjustments are quick and easy.
© October 2011
Page 11 of 23
***SPECIAL NOTE***
Pre-Focus your microscope so that focus is approximately on the tweezers almost parallel to the work
platform. You will also want to first start at low magnification to find the strain pattern then increase
power setting to desired strength.
© October 2011
Page 12 of 23
A Polarized Microscope Set-up is ONE of the Most Important Features NEEDED TODAY!!!!
This is ONE of the MAIN Observational Tools needed to help Identify Natural vs. Synthetic Diamond
***SPECIAL NOTE***
This article DOES NOT teach or train how to Identify Natural vs. Synthetic Diamond
You will also need to take a Special Advanced Hand-On Class Room Training Session to help aid you in
what to look for as far as Clues that you will observe that will instantly raise the Red Warning Flags to
caution you to slow down and think things through before opening your mouth and making a statement
you might regret later on.
***SPECIAL RESOURCE MANUALS***
YOU WILL WANT TO PURCHASE and READ COVER-to-COVER***
***Laboratory-Grown Diamonds
Informational Guide to HPHT-grown and CVD-grown Diamonds
Second (2nd Edition)
By Branko Deljanin & Dusan Simic
***Natural or Synthetic Diamond
Identifying with CPF, DF and UV Light
By Dusan Simic
Analytical Gemology & Jewellery
For more information on Analytical Gemology and Jewelry call (917) 667-6936
***Identifying Diamond Types and Synthetic Diamonds with CPF (Cross Polarized Filters)
Second (2nd Edition)
By Dusan Simic
Analytical Gemology & Jewellery
For more information on Analytical Gemology and Jewelry call (917) 667-6936
The above Three (3) Manuals are a MUST READ for every gemologist and gem & Jewelry appraiser!!!
© October 2011
Page 13 of 23
© October 2011
Page 14 of 23
© October 2011
Page 15 of 23
© October 2011
Page 16 of 23
© October 2011
Page 17 of 23
© October 2011
Page 18 of 23
© October 2011
Page 19 of 23
© October 2011
Page 20 of 23
© October 2011
Page 21 of 23
© October 2011
Page 22 of 23
© October 2011
Page 23 of 23

Polarized Filter Set for your Microscope for under

Transcription

Similar documents

View

BOOK YOUR Build•A•Party Celebrate Summer! - Build-A

Conjunction Junction

MONDAY-FRIDAY

quailwood times - Quailwood Community

How to Make A Korovai

Pottery Wheel Mania!

California Bluegrass Association

March 31, 2016 - Mt Bethel Blog