KITZ CORPORATION OF AMERICA

Transcription

•
BIV-100-0205
GENERAL TERMS AND CONDITIONS
ACCEPTANCE
All quotations are for acceptance within
30 days from date of quotation unless
extended in writing. In the event a purchase order is placed after this time, the
Seller’s company reserves the right to
requote prices of all valves offered. All
orders and contracts are subject to credit approval and acceptance by KITZ.
DEFERRED SHIPMENTS
WARRANTY
If for any reason the Buyer desires to
delay shipments more than 30 days after
manufacturing or to place a hold or to
stop the order during the manufacturing
cycle, the Seller’s company reserves the
right to consider the order cancelled and
to invoke cancellation charges.
FREIGHT
CREDIT TERMS
All materials will be shipped F.O.B.
point of shipment – no freight allowance
unless otherwise stated and agreed upon
with the Buyer.
As quoted. Overdue balances will be
subject to 1.5% service charge per month
on such indebtedness.
Seller will replace without charge or
refund the purchase price of products
manufactured by Seller which prove to
be defective in material or workmanship, provided in each case that the
product is properly installed and is used in
the service for which Seller recommends
it and that written claim, specifying the
alleged defect, is presented to the Seller
within one year from the date of shipment. Seller shall in no event be responsible for claims of A) labor, expenses, or
other damages occasioned by defective
parts or products or for B) consequential
or secondary damages. The Warranty
stated in this paragraph is in lieu of all
other warranties, either expressed or
implied. With respect to warranties,
this paragraph states Buyer’s exclusive
remedy and Seller’s exclusive liability.
PRICES
DELIVERIES
There will be added to all prices quoted
any sales, excise, or similar tax which
Seller may be required to collect on or in
connection with the sale. Seller reserves
the right to cancel any order in the event
that selling prices shall be established by
Federal, State or other governmental
regulation with respect to the products
covered by the order which shall be
lower than the prices specified in the
order.
Shipments made to the Buyer shall at all
times be subject to the approval of
Seller’s Credit Department. All schedules
of shipments are estimated as closely as
possible and Seller will use its best
effort to ship within the time schedule
but does not guarantee to do so. Seller
shall not be liable for any direct, indirect, or consequential damage or loss
caused by delay in delivery, regardless
of the cause of delay. Items offered
from stock are subject to prior sale.
ESCALATION TERMS
RETURNS
Prices shown in this price schedule
reflect the costs in effect at the time of
publication. These prices will remain
firm on all products with a quoted delivery of twenty six (26) weeks or less. On
products with a quoted delivery of more
than 26 weeks, the Seller has a right to
price and invoice at the applicable price
sheet in effect at the time of shipment.
In no event will the invoiced price be
less than price originally quoted.
No returns are allowed without prior
arrangements made with the Seller.
Product considered for return must be in
new, resalable condition and of current
design.
BIV-2
DESIGN
Because of a policy of continuous product improvement, Seller reserves the
right to change design, materials or specifications without notice. There will be a
charge for modifying an order after it
has been entered when such change or
modification results in additional engineering or clerical work for either
KITZ or its suppliers.
NOTE
KITZ reserves the right to correct any
obvious clerical errors in quotations,
invoices and other contracts.
10750 CORPORATE DRIVE • STAFFORD, TEXAS
®
®
A PRODUCT OF TECHNOLOGY
GENERAL INDEX
Page
Page
STAINLESS STEEL VALVES............BIV-38 – BIV-42
GATE......................................................BIV-05 – BIV-13
GATE......................................................BIV-34
GLOBE (ANGLE) .................................BIV-14 – BIV-21
GLOBE...................................................BIV-41
CHECK ..................................................BIV-22 – BIV-28
CHECK ..................................................BIV-42
IRON VALVES .....................................BIV-29 – BIV-37
STRAINERS .........................................BIV-43 – BIV-45
GATE......................................................BIV-31 – BIV-33
BRONZE................................................BIV-44
GLOBE...................................................BIV-34 – BIV-35
IRON ......................................................BIV-45
CHECK ..................................................BIV-36 – BIV-37
ENGINEERING DATA INDEX .........BIV-46 – BIV-67
CODE # INDEX
Page
BRONZE GATE
Threaded
24 . . . . . . . . . . . . . . . . . . . . . . . . .BIV-8
25 . . . . . . . . . . . . . . . . . . . . . . . .BIV-10
27 . . . . . . . . . . . . . . . . . . . . . . .BIV-6, 7
37 . . . . . . . . . . . . . . . . . . . . . . . .BIV-13
40 . . . . . . . . . . . . . . . . . . . . . . . . .BIV-9
42T . . . . . . . . . . . . . . . . . . . . . .BIV-11
46 . . . . . . . . . . . . . . . . . . . . . . . .BIV-12
Solder
28 . . . . . . . . . . . . . . . . . . . . . . .BIV-6, 7
41 . . . . . . . . . . . . . . . . . . . . . . . . .BIV-9
43 . . . . . . . . . . . . . . . . . . . . . . . .BIV-11
44 . . . . . . . . . . . . . . . . . . . . . . . . .BIV-8
45 . . . . . . . . . . . . . . . . . . . . . . . .BIV-10
64 . . . . . . . . . . . . . . . . . . . . . . . .BIV-12
BRONZE GLOBE
Threaded
02 . . . . . . . . . . . . . . . . . . . . . . . .BIV-16
09 . . . . . . . . . . . . . . . . . . . . . . . .BIV-17
11 . . . . . . . . . . . . . . . . . . . . . . . .BIV-15
17 . . . . . . . . . . . . . . . . . . . . . . . .BIV-19
17S . . . . . . . . . . . . . . . . . . . . . .BIV-20
18 . . . . . . . . . . . . . . . . . . . . . . . .BIV-21
38 . . . . . . . . . . . . . . . . . . . . . . . .BIV-18
Page
BRONZE CHECK
Threaded
04 . . . . . . . . . . . . . . . . . . . . . . . .BIV-23
19 . . . . . . . . . . . . . . . . . . . . . . . .BIV-28
22 . . . . . . . . . . . . . . . . . . . . . . . .BIV-24
22T . . . . . . . . . . . . . . . . . . . . . .BIV-25
29 . . . . . . . . . . . . . . . . . . . . . . . .BIV-27
36 . . . . . . . . . . . . . . . . . . . . . . . .BIV-26
Page
CHECK
78 . . . . . . . . . . . . . . . . . . . . . . . .BIV-36
79 . . . . . . . . . . . . . . . . . . . . . . . .BIV-37
Solder
14 . . . . . . . . . . . . . . . . . . . . . . . .BIV-23
23 . . . . . . . . . . . . . . . . . . . . . . . .BIV-24
23T . . . . . . . . . . . . . . . . . . . . . .BIV-25
26 . . . . . . . . . . . . . . . . . . . . . . . .BIV-26
30 . . . . . . . . . . . . . . . . . . . . . . . .BIV-27
STAINLESS STEEL VALVES
31 (Gate) . . . . . . . . . . . . . . . . . .BIV-40
33 (Globe) . . . . . . . . . . . . . . . . .BIV-41
34 (Check) . . . . . . . . . . . . . . . . .BIV-42
STRAINERS
Flanged
80 . . . . . . . . . . . . . . . . . . . . . . . .BIV-45
BRONZE STRAINERS
Threaded/Solder
15/16 . . . . . . . . . . . . . . . . . . . . .BIV-44
CAST IRON, FLANGED
GATE
72 . . . . . . . . . . . . . . . . . . . . . . . .BIV-31
73 . . . . . . . . . . . . . . . . . . . . . . . .BIV-32
75 . . . . . . . . . . . . . . . . . . . . . . . .BIV-33
GLOBE
76 . . . . . . . . . . . . . . . . . . . . . . . .BIV-34
77 . . . . . . . . . . . . . . . . . . . . . . . .BIV-35
Solder
10 . . . . . . . . . . . . . . . . . . . . . . . .BIV-17
12 . . . . . . . . . . . . . . . . . . . . . . . .BIV-15
®
BIV-3
GENERAL INDEX
BRONZE VALVES...............................BIV-04 – BIV-28
BRONZE VALVES
BRONZE VALVES
KITZ Bronze Valves are built on fully automated molding and machining lines. This highly automated
process achieves consistent precision in manufacturing Commercial and Industrial valves for water, oil,
gas and steam services. More than a promise of excellent performance, they deliver the needed efficiency
for all around problem-free flow control.
1
“Sure Grip” Handwheel - for easy operation.
2
Hex Head Packing Nut, made of Forged Brass
(ASTM B283) for extra strength, can be easily
loosened or tightened providing simple
packing replacement.
3
4
1
Deep stuffing box has “NON-ASBESTOS
PACKING”. It’s made of Aramid Fiber with
Graphite, ideal for leak-free service and
reduced operating torque.
2
The rising stem design provides visual
indication that the valve is open or closed.
3
Stems are made of ASTM B62 bronze. This
heavy duty design assures long-life service
and protection from dezincification.
5
6
4
Stem and integral back seat are precision
machined for emergency repacking of the
valve and keeps the stem thread out of direct
contact with the flow media.
6
5
Union Bonnet construction assures leak-tight
performance at higher pressures and elevated
temperatures.
7
Body and bonnets are made of ASTM B62
bronze. The design, material, and workmanship effectively help to lower maintenance
costs and assures long-life service.
Code #42 (AK150LUT)
7
BIV-4
Discs are made of ASTM B62 Bronze and are
fully guided on precision seating surfaces for
accurate alignment and leak-free performance.
®
®
BRONZE GATE VALVES
ILLUSTRATED INDEX
CODE #
125 WSP/200 WOG
Screw-Over-Bonnet
Non-Rising Stem
125 WSP/200 WOG
Screw-In-Bonnet
Rising Stem
125 WSP/200 WOG
Screw-In-Bonnet
Non-Rising Stem
AKH Code # 27
Size 3/8″ - 4″
(Threaded)
AK125M Code # 24
Size 1/2″ - 3″
(Threaded)
AK125E Code # 40
Size 3/8″ - 2″
(Threaded)
CH Code # 28
Size 3/8″ - 4″
(Solder)
C125M Code # 44
Size 1/2″ - 2″
(Solder)
C125E Code # 41
Size 3/8″ - 2″
(Solder)
150 WSP/300 WOG
Screw-In-Bonnet
Rising Stem
150 WSP/300 WOG
Union Bonnet
Rising Stem
150 WSP/300 WOG
Screw-In-Bonnet
Non-Rising Stem
AK150L Code # 25
Size 1/2″ - 3″
(Threaded)
AK150LUT Code # 42T
Size 1/4″ - 2″
(Threaded)
AK150E Code # 46
Size 3/8″ - 2″
(Threaded)
C150L Code # 45
Size 1/2″ - 2″
(Solder)
C150LU Code # 43
Size 1/2″ - 2″
(Solder)
C150E Code # 64
Size 1/2″ - 2″
(Solder)
BRONZE GATE VALVES ILLUSTRATED INDEX
NUMERICAL
INDEX
PAGE
24.................................BIV-8
25...............................BIV-10
27..............................BIV-6,7
28..............................BIV-6,7
37...............................BIV-13
40.................................BIV-9
41.................................BIV-9
42T.............................BIV-11
43 ...............................BIV-11
44.................................BIV-8
45...............................BIV-10
46...............................BIV-12
64...............................BIV-12
300 WSP/1000 WOG
Union Bonnet
Rising Stem
AK300LU Code # 37
Size 3/8″- 2″
(Threaded)
®
BIV-5
GATE
CLASS 125 BRONZE
Screw-Over-Bonnet • Non-Rising Stem
Solid Wedge Disc
BRONZE GATE
CODE # 27 (AKH)
THREADED
STANDARDS
END TO END
THREADED ENDS
SOLDER JOINT ENDS
WALL THICKNESS
DESIGN
KITZ
ANSI B1.20.1
ANSI B16.18
KITZ
KITZ
PRESSURE/TEMPERATURE
125 PSI - SATURATED STEAM TO 353ºF
- FLUID TO 406ºF
200 PSI NON-SHOCK COLD WATER, OIL OR GAS
*SEE PRESSURE/TEMPERATURE LIMITATIONS FOR SOLDER JOINT
VALVES - PAGE BIV-50.
MATERIAL LIST
NO.
1
2
3
4
5
6
7
8
9
10
16
NAME OF PART
SPECIFICATION
BODY
BONNET
STEM
DISC (3/8 – 1/2)
(3/4 – 2)
LOCK NUT
PACKING NUT
GLAND
GLAND PACKING
HAND WHEEL (3/8 – 11/4)
(11/2 – 2)
WHEEL NUT
NAME PLATE
CAST BRONZE (ASTM B62)
BRASS (KITZ “K” METAL)
KITZ "K" METAL
BRASS ROD (B16)
FORGED BRASS (B283, C37700)
BRASS ROD (B16)
ARAMID FIBERS W/ GRAPHITE
ZINC DIE-CAST (B86)
ALUMINUM DIE-CAST (B85)
CARBON STEEL (A307 Gr. B)
ALUMINUM
DIMENSIONS - WEIGHTS - QUANTITIES
11/2 & 2
CODE # 28 (CH)
SOLDER*
BIV-6
d2
SIZE
H
D1
L
L1
3/8
2.91
3.15
3.54
4.13
4.65
5.31
6.26
1.97
1.97
2.17
2.36
2.76
3.15
3.54
1.65
1.77
1.97
2.24
2.40
2.64
2.91
.78
.81
.90
1.01
1.13
1.25
1.34
1/2
3/4
1
11/4
11/2
2
d1
APPROX. CARTON
Max. Min. NET WT.
QTY
.506
.631
.881
1.132
1.382
1.633
2.133
.502
.627
.877
1.128
1.378
1.628
2.128
0.58
0.71
0.90
1.43
1.93
2.63
4.19
96
48
30
40
30
24
16
®
GATE
CLASS 125 BRONZE
Screw-In-Bonnet • Non-Rising Stem
Solid Wedge Disc
BRONZE GATE
BRONZE GATE
CODE # 27 (AKH)
THREADED
STANDARDS
END TO END
THREADED ENDS
SOLDER JOINT ENDS
WALL THICKNESS
DESIGN
KITZ
ANSI B1.20.1
ANSI B16.18
KITZ
KITZ
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
3
4
5
6
7
8
9
10
16
CODE # 28 (CH)
SOLDER*
®
NAME OF PART
SPECIFICATION
BODY
BONNET
STEM
DISC
LOCK NUT
PACKING NUT
GLAND
GLAND PACKING
HAND WHEEL
WHEEL NUT
NAME PLATE
BRASS ROD (B16)
BRASS ROD (B16)
CARBON STEEL
ALUMINUM
d2
SIZE
H
D1
L
L1
21/2
3
4
7.95
8.78
11.02
4.53
5.31
6.10
3.54
3.94
4.76
1.59
1.78
2.49
d1
Max. Min.
2.633
3.133
4.133
2.628
3.128
4.128
APPROX.
NET WT.
CARTON
QTY
7.50
10.30
21.33
8
6
3
BIV-7
GATE
CLASS 125 BRONZE
BRONZE GATE
Screw-In-Bonnet • Rising Stem
Solid Wedge Disc
CODE # 24 (AK125M)
THREADED
STANDARDS
END TO END
THREADED ENDS
SOLDER JOINT ENDS
DESIGN
MILITARY
KITZ
ANSI B1.20.1
ANSI B16.18
MSS SP-80, TYPE 2
MSS SP-80, TYPE 2
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
3
4
6
7
8
9
10
16
NAME OF PART
SPECIFICATION
BODY
BONNET
STEM
DISC
PACKING NUT
GLAND
GLAND PACKING
HAND WHEEL (1/2 – 1)
(11/4 – 3)
WHEEL NUT
NAME PLATE
BRASS ROD (B16)
ZINC DIE-CAST (B86)
BRASS ROD (B16)
ALUMINUM
CODE # 44 (C125M)
SOLDER*
d2
SIZE
H
1/2
5.08
6.10
7.09
8.50
10.12
11.65
14.61
17.01
3/4
1
11/4
11/2
2
21/2
3
BIV-8
D1
2.17
2.36
2.76
3.15
3.54
3.94
5.31
6.10
L
2.01
2.20
2.60
2.68
2.91
3.31
4.53
5.12
L1
.93
1.02
1.17
1.29
1.21
1.61
–
–
d1
Max.
.631
.881
1.132
1.382
1.633
2.133
–
–
Min.
.627
.877
1.128
1.378
1.628
2.128
–
–
APPROX. CARTON
NET WT.
QTY
0.98
1.58
2.13
3.00
4.33
6.38
12.80
19.30
48
36
24
16
12
8
4
3
®
GATE
CLASS 125 BRONZE
Screw-In-Bonnet • Non-Rising Stem
Solid Wedge Disc
BRONZE GATE
CODE # 40 (AK125E)
THREADED
STANDARDS
END TO END
THREADED ENDS
SOLDER JOINT ENDS
DESIGN
MILITARY
KITZ
ANSI B1.20.1
ANSI B16.18
MSS SP-80, TYPE 1A
MSS SP-80, TYPE 1A
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
3
4
6
7
8
9
CODE # 41 (C125E)
SOLDER*
10
15
16
NAME OF PART
SPECIFICATION
BODY
BONNET
STEM
DISC
PACKING NUT
GLAND
GLAND PACKING
(11/4 – 2)
WHEEL NUT
STUFFIN BOX
NAME PLATE
BRASS ROD (B16)
ZINC DIE-CAST (B86)
BRASS ROD (B16)
BRASS ROD (B16)
ALUMINUM
d2
SIZE
H
D1
L
L1
3/8
3.89
3.66
4.33
4.96
5.71
6.69
7.44
1.97
2.17
2.36
2.76
3.15
3.54
3.94
1.69
1.93
2.09
2.40
2.52
2.68
2.91
.78
.81
.86
.98
1.17
1.28
1.57
1/2
3/4
1
11/4
11/2
2
®
d1
APPROX. CARTON
Max. Min. NET WT.
QTY
.506
.631
.881
1.132
1.382
1.633
2.133
.502
.627
.877
1.128
1.378
1.628
2.128
0.70
0.85
1.17
1.72
2.42
3.33
4.76
96
72
54
36
24
18
12
BIV-9
GATE
CLASS 150 BRONZE
BRONZE GATE
Screw-In-Bonnet • Rising Stem
Solid Wedge Disc
CODE # 25 (AK150L)
THREADED
STANDARDS
END TO END
THREADED ENDS
SOLDER JOINT ENDS
DESIGN
MILITARY
KITZ
ANSI B1.20.1
ANSI B16.18
MSS SP-80, TYPE 2
MSS SP-80, TYPE 2
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
3
4
6
7
8
9
10
16
NAME OF PART
SPECIFICATION
BODY
BONNET
STEM
DISC
PACKING NUT
GLAND
GLAND PACKING
(11/4 – 3)
WHEEL NUT
NAME PLATE
BRASS ROD (B16)
ZINC DIE-CAST (B86)
BRASS ROD (B16)
ALUMINUM
CODE # 45 (C150L)
SOLDER*
d2
SIZE
H
D1
L
L1
1/2
5.39
6.18
7.09
8.50
10.12
11.65
15.16
17.01
2.17
2.76
2.76
3.15
3.54
3.94
6.10
6.10
2.01
2.20
2.60
2.68
2.91
3.31
4.72
5.51
.93
1.02
1.17
1.29
1.21
1.61
–
–
3/4
1
11/4
11/2
2
21/2
3
BIV-10
d1
Max. Min.
.631
.881
1.132
1.382
1.633
2.133
–
–
.627
.877
1.128
1.378
1.628
2.128
–
–
APPROX. CARTON
NET WT.
QTY
1.00
1.50
1.72
3.88
4.33
6.38
14.75
20.33
48
36
24
16
12
8
4
3
®
GATE
CLASS 150 BRONZE
Union Bonnet • Rising Stem
Solid Wedge Disc
BRONZE GATE
CODE # 42T (AK150LUT)
THREADED
STANDARDS
END TO END
THREADED ENDS
SOLDER JOINT ENDS
DESIGN
MILITARY
KITZ
ANSI B1.20.1
ANSI B16.18
MSS SP-80, TYPE 2
MSS SP-80, TYPE 2
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
3
4
6
7
8
9
10
11
16
CODE # 43 (C150LU)
SOLDER*
NAME OF PART
SPECIFICATION
BODY
BONNET
STEM
DISC
PACKING NUT
GLAND
BRASS ROD (B16)
GLAND PACKING
ARAMID FIBERS PTFE
ZINC DIE-CAST (B86)
(11/4 – 2)
WHEEL NUT
BRASS ROD
BONNET RING
CAST BRONZE (B62)
NAME PLATE
ALUMINUM
* OPTION AVAILABLE: GRAPHOIL PACKING
d2
SIZE
H
D1
L
L1
1/4
4.25
1.97
1.77
–
–
–
0.88
60
3/8
4.25
5.39
6.18
7.09
8.50
10.12
11.65
1.97
2.17
2.76
2.76
3.15
3.54
3.94
1.81
2.01
2.20
2.60
2.68
2.91
3.31
–
.93
1.02
1.17
1.29
1.21
1.61
–
.631
.881
1.132
1.382
1.633
2.133
–
.627
.877
1.124
1.378
1.628
2.128
0.88
1.13
1.64
2.46
3.50
4.84
7.25
60
48
36
24
16
12
8
1/2
3/4
1
11/4
11/2
2
®
d1
APPROX. CARTON
Max. Min. NET WT.
QTY
BIV-11
GATE
CLASS 150 BRONZE
BRONZE GATE
Screw-In Bonnet • Inside Screw • Non-Rising Stem
Solid Wedge Disc
CODE # 46 (AK150E)
THREADED
STANDARDS
END TO END
THREADED ENDS
SOLDER JOINT ENDS
DESIGN
MILITARY
KITZ
ANSI B1.20.1
ANSI B16.18
MSS SP-80, TYPE 1A
MSS SP-80, TYPE 1A
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
3
4
6
7
8
9
10
15
16
NAME OF PART
SPECIFICATION
BODY
BONNET
STEM
DISC
PACKING NUT
GLAND
GLAND PACKING
(11/4 – 2)
WHEEL NUT
STUFFING BOX (3/8 – 11/2)
(2)
NAME PLATE
BRASS ROD (B16)
ZINC DIE-CAST (B86)
BRASS ROD
BRASS ROD (B16)
FORGED BRASS (B283, 37700)
ALUMINUM
CODE # 64 (C150E)
SOLDER*
SIZE
d2
H
D1
L
L1
3/8
3.39
3.86
4.49
4.96
5.70
6.92
7.91
1.97
2.17
2.76
2.76
3.15
3.54
3.94
1.69
1.93
2.09
2.40
2.68
2.91
3.31
–
.81
.86
.98
1.17
1.28
1.57
1/2
3/4
1
11/4
11/2
2
BIV-12
d1
Max. Min.
–
.631
.881
1.132
1.382
1.633
2.133
–
.627
.877
1.128
1.378
1.628
2.128
APPROX. CARTON
NET WT.
QTY
0.68
0.97
1.24
1.72
2.75
4.06
6.38
96
72
54
36
24
16
8
®
GATE
CLASS 300 BRONZE
Union Bonnet • Rising Stem
Solid Wedge Disc
BRONZE GATE
CODE # 37 (AK300LU)
THREADED
STANDARDS
END TO END
THREADED ENDS
DESIGN
MILITARY
KITZ
ANSI B1.20.1
MSS SP-80, TYPE 2
MSS SP-80, TYPE 2
- FLUID TO 550ºF
MATERIAL LIST
NO.
NAME OF PART
SPECIFICATION
1
2
3
4
BODY
BONNET
STEM
DISC
6
7
8
9
PACKING NUT
GLAND
GLAND PACKING
HAND WHEEL (3/8 – 1/2)
(3/4 – 2)
WHEEL NUT
BONNET RING
NAME PLATE
COPPER-NICKEL ALLOY
(B584, C97600)
BRASS ROD (B16)
FLEXIBLE GRAPHITE & ALUM.
ZINC DIE-CAST (B86)
BRASS ROD
CAST BRONZE (B61)
ALUMINUM
10
11
16
d2
SIZE
H
D1
L
3/8
4.92
5.87
6.81
7.64
8.98
10.79
12.32
2.36
2.76
3.15
3.15
3.94
4.53
5.31
1.81
2.01
2.20
2.60
2.91
3.31
3.86
1/2
3/4
1
11/4
11/2
2
®
APPROX. CARTON
NET WT.
QTY
1.04
1.31
1.79
2.50
4.17
6.00
9.50
48
36
24
18
12
8
4
BIV-13
®
BRONZE GLOBE VALVES ILLUSTRATED INDEX
BRONZE GLOBE VALVES
ILLUSTRATED INDEX
125 WSP/200 WOG
Screw-In Bonnet
Rising Stem
NUMERICAL
INDEX
CODE #
PAGE
02...............................BIV-16
09...............................BIV-17
10...............................BIV-17
11 ...............................BIV-15
12...............................BIV-15
17...............................BIV-19
17S.............................BIV-20
18...............................BIV-21
38...............................BIV-18
AK125C Code # 11
Size 1/2″ - 3″
(Threaded)
C125C Code # 12
Size 1/2″ - 3″
(Solder)
150 WSP/300 WOG
Screw-In-Bonnet
Rising Stem
AKC Code # 02
Size 1/4″ - 3″
(Threaded)
150 WSP/300 WOG
Union Bonnet/PTFE Disc
Rising Stem
150WSP/300 WOG
Screw-In-Bonnet
Rising Stem
AK150D Code # 09
Size 1/4″ - 3″
(Threaded)
AKCA Code # 38
Size 1/4″ - 3″
(Threaded)
C150D Code # 10
Size 1/4″ - 3″
(Solder)
BIV-14
300 WSP/600 WOG
Union Bonnet
Rising Stem
300 WSP/600 WOG
Union Bonnet / S.S. Disc & Seat
Rising Stem
300 WSP/600 WOG
Union Bonnet / PTFE Seat
Rising Stem
AK300J Code # 17
Size 1/4″ - 2″
(Threaded)
AK300JS Code # 17S
Size 1/2″ - 2″
(Threaded)
AK300D Code # 18
Size 1/4″ - 2″
(Threaded)
®
GLOBE
CLASS 125 BRONZE
Screw-In-Bonnet • Inside Screw • Rising Stem
Integral Seat • Solid Wedge Disc
BRONZE GLOBE
CODE # 11 (AK125C)
THREADED
STANDARDS
END TO END
THREADED ENDS
DESIGN
MILITARY
KITZ
ANSI B1.20.1
MSS SP-80, TYPE 1
MSS SP-80, TYPE 1
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
CODE # 12 (C125C)
SOLDER
3
4
5
6
7
8
9
10
16
NAME OF PART
SPECIFICATION
BODY
BONNET (1/2 – 2)
(21/2, 3)
STEM
DISC
LOCK NUT
PACKING NUT
GLAND
GLAND PACKING
(1 – 3)
WHEEL NUT
NAME PLATE
CAST BRONZE (B62)
FORGED BRASS (B283 C37700)
CAST BRONZE (B62)
BRASS (B62)
CAST BRONZE (B62)
BRASS ROD (B16)
ZINC DIE-CAST (B86)
BRASS ROD (B16)
ALUMINUM
SIZE
d2
H
D1
L
L1
1/2
2.99
3.86
4.25
5.39
6.30
7.09
7.95
9.69
2.36
2.76
3.15
3.54
3.94
4.53
5.31
6.10
2.09
2.56
3.03
3.35
3.94
4.69
5.91
7.01
1.52
1.80
2.12
2.60
2.94
3.43
4.61
5.81
3/4
1
11/4
11/2
2
21/2
3
®
APPROX. CARTON
NET WT.
QTY
0.71
1.37
1.80
2.63
3.88
6.63
10.51
15.54
48
36
36
16
12
8
4
3
BIV-15
GLOBE
CLASS 150 BRONZE
BRONZE GLOBE
Integral Seat • Solid Wedge Disc
CODE # 02 (AKC)
THREADED
STANDARDS
END TO END
THREADED ENDS
DESIGN
KITZ
ANSI B1.20.1
KITZ
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
3
4
5
6
7
8
9
10
16
NAME OF PART
SPECIFICATION
BODY
BONNET (1/4 – 21/2)
(3)
STEM
DISC
LOCK NUT
PACKING NUT
GLAND
GLAND PACKING
(1 – 3)
WHEEL NUT
NAME PLATE
CAST BRONZE (B584, C84400)
BRASS ROD (B16)
ZINC DIE-CAST (B86)
CARBON STEEL
ALUMINUM
d2
SIZE
H
D1
L
1/4
2.60
2.68
3.11
3.66
4.09
5.00
5.71
6.85
7.83
8.46
1.97
1.97
2.36
2.76
3.15
3.54
3.94
4.53
5.31
6.10
1.73
1.73
2.09
2.56
3.03
3.35
3.94
4.69
5.47
6.22
3/8
1/2
3/4
1
11/4
11/2
2
21/2
3
BIV-16
APPROX. CARTON
NET WT.
QTY
35
43
43
65
60
65
66
51
55
55
80
80
60
56
36
25
16
8
6
4
®
GLOBE
CLASS 150 BRONZE
Union-Bonnet • Inside Screw • Rising Stem
G/F PTFE Disc
BRONZE GLOBE
CODE # 09 (AK150D)
THREADED
STANDARDS
END TO END
THREADED ENDS
SOLDER JOINT ENDS
DESIGN
MILITARY
KITZ
ANSI B1.20.1
ANSI B16.18
MSS SP-80, TYPE 2
MSS SP-80, TYPE 2
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
3
4
6
7
8
9
10
11
12
13
14
16
19
33
35
NAME OF PART
SPECIFICATION
BODY
BONNET
STEM
DISC
PACKING NUT
GLAND
GLAND PACKING
(3/4 – 21/2)
(3)
WHEEL NUT
BONNET RING (1/4 – 2)
DISC HOLDER
DISC NUT (1/4 – 3/4)
(1 – 3)
SPLIT PIN
NAME PLATE
GASKET
BONNET NUT
BONNET BOLT
G/F PTFE
BRASS ROD (B16)
ZINC DIE-CAST (B86)
DUCTILE IRON (A536)
BRASS ROD (B16)
CAST BRONZE (B62)
CAST BRONZE (B62)
BRASS ROD (B16)
COPPER
ALUMINUM
ARAMID FIBER SHEET
BRASS ROD (B16)
CARBON STEEL
21/2" & Larger
CODE # 10 (C150D)
SOLDER*
d2
SIZE
H
D1
L
L1
1/4
4.29
2.36
2.09
1.66
.381
.377
0.96
48
3/8
4.29
4.57
5.35
5.87
6.81
7.17
8.23
9.72
10.83
2.36
2.76
3.54
3.94
4.53
4.53
5.31
6.10
7.09
2.17
2.52
3.07
3.54
4.13
4.72
5.71
6.69
7.87
1.64
1.83
2.24
2.59
3.02
3.53
4.41
5.13
6.29
.506
.631
.881
1.132
1.382
1.633
2.133
2.633
3.133
.502
.627
.877
1.128
1.378
1.628
2.128
2.628
3.128
0.98
1.11
1.88
3.13
4.42
5.75
10.50
17.33
28.00
48
36
24
16
12
8
4
3
1
1/2
3/4
1
11/4
11/2
2
21/2
3
®
d1
Max. Min.
APPROX. CARTON
NET WT.
QTY
BIV-17
ANGLE GLOBE
CLASS 150 BRONZE
BRONZE ANGLE GLOBE
Bronze Disc
CODE # 38 (AKCA)
THREADED
STANDARDS
END TO END
THREADED ENDS
DESIGN
KITZ
ANSI B1.20.1
KITZ
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
3
4
5
6
7
8
9
10
16
NAME OF PART
SPECIFICATION
BODY
BONNET (1/4 – 21/2)
(3)
STEM
DISC
LOCK NUT
PACKING NUT
GLAND
GLAND PACKING
(1 – 3)
WHEEL NUT
NAME PLATE
BRASS ROD (B16)
ZINC DIE-CAST (B86)
ALUMINUM DIE-CAST ( B85)
CARBON STEEL
ALUMINUM
d2
SIZE
H
D1
L
1/4
2.60
2.68
3.11
3.66
4.09
5.00
5.71
6.85
7.83
8.46
1.97
1.97
2.36
2.76
3.15
3.54
3.94
4.53
5.31
6.10
.83
.95
1.10
1.34
1.57
1.85
2.05
2.40
2.91
3.35
3/8
1/2
3/4
1
11/4
11/2
2
21/2
3
APPROX. CARTON
NET WT.
QTY
0.44
0.51
0.58
0.98
1.42
2.28
3.56
6.13
8.50
11.50
80
80
60
56
36
25
16
8
6
4
NOTE: NOT INTENDED FOR USE IN A POTABLE WATER SYSTEM - COMPLIANT STATEMENT
PROP 65, STATE OF CALIFORNIA
BIV-18
®
GLOBE
CLASS 300 BRONZE
Union Bonnet • Inside Screw • Rising Stem
Integral Seat • Bronze Disc
BRONZE GLOBE
CODE # 17 (AK300J)
THREADED
STANDARDS
END TO END
THREADED ENDS
DESIGN
MILITARY
KITZ
ANSI B1.20.1
MSS SP-80, TYPE 1
MSS SP-80, TYPE 1
- FLUID TO 550ºF
MATERIAL LIST
NO.
1
2
3
4
5
6
7
8
9
10
11
16
NAME OF PART
SPECIFICATION
BODY
BONNET
STEM
DISC
LOCK NUT
PACKING NUT
GLAND
GLAND PACKING
(1/2 – 2)
WHEEL NUT
BONNET RING
NAME PLATE
BRASS ROD (B16)
BRASS ROD (B16)
ZINC DIE-CAST (B86)
BRASS ROD (B16)
CAST BRONZE (B61)
ALUMINUM
d2
SIZE
H
D1
L
1/4
4.45
4.45
4.96
5.47
6.26
7.36
7.68
8.82
2.36
2.36
3.15
3.54
3.94
4.53
5.31
6.10
2.09
2.17
2.52
3.07
3.54
4.13
4.72
5.71
3/8
1/2
3/4
1
11/4
11/2
2
®
APPROX. CARTON
NET WT.
QTY
1.00
1.04
1.31
1.96
2.94
5.00
6.38
10.25
48
48
36
24
16
12
8
4
BIV-19
GLOBE
CLASS 300 BRONZE
BRONZE GLOBE
Stainless Steel Disc & Seat
CODE # 17S (AK300JS)
THREADED
STANDARDS
END TO END
THREADED ENDS
DESIGN
MILITARY
KITZ
ANSI B1.20.1
MSS SP-80, TYPE 3
MSS SP-80, TYPE 3
- FLUID TO 550ºF
MATERIAL LIST
NO.
NAME OF PART
SPECIFICATION
1
2
3
4
BODY
BONNET
STEM
DISC
5
6
7
8
9
10
11
16
30
LOCK NUT
PACKING NUT
GLAND
GLAND PACKING
HAND WHEEL
WHEEL NUT
BONNET RING
NAME PLATE
BODY SEAT RING
STAINLESS STEEL (A276, TYPE 403)
(HB 310 ~ 360)
BRASS ROD (B16)
BRASS ROD (B16)
BRASS ROD (B16)
CAST BRONZE (B61)
ALUMINUM
(HB 220 ~ 260)
d2
SIZE
H
D1
L
1/2
4.92
5.47
6.14
7.36
7.56
8.66
3.15
3.54
3.94
4.53
5.31
6.10
2.52
3.07
3.54
4.13
4.72
5.71
3/4
1
11/4
11/2
2
BIV-20
APPROX. CARTON
NET WT.
QTY
1.31
1.96
2.94
5.00
6.38
10.25
36
24
16
12
8
4
®
GLOBE
CLASS 300 BRONZE
G/F PTFE Disc
BRONZE GLOBE
CODE # 18 (AK300D)
THREADED
STANDARDS
END TO END
THREADED ENDS
DESIGN
MILITARY
KITZ
ANSI B1.20.1
MSS SP-80, TYPE 2
MSS SP-80, TYPE 2
- FLUID TO 421 ºF
MATERIAL LIST
NO.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
16
NAME OF PART
SPECIFICATION
BODY
BONNET
STEM
DISC
LOCK NUT
PACKING NUT
GLAND
GLAND PACKING
(1/2 – 2)
WHEEL NUT
BONNET RING
DISC HOLDER (1/4 – 3/4)
(1 – 2)
DISC NUT (1/4 – 3/4)
(1 – 2)
SPLIT PIN
NAME PLATE
G/F PTFE
BRASS ROD (B124 C37700)
BRASS ROD (B16)
ZINC DIE-CAST (B86)
BRASS ROD (B16)
CAST BRONZE (B61)
BRASS ROD (B16)
CAST BRONZE (B61)
BRASS ROD (B16)
COPPER
ALUMINUM
d2
SIZE
H
D1
L
1/4
4.45
4.45
4.96
5.47
6.18
7.36
7.56
8.70
2.36
2.36
3.15
3.54
3.94
4.53
5.31
6.10
2.09
2.17
2.52
3.07
3.54
4.13
4.72
5.71
3/8
1/2
3/4
1
11/4
11/2
2
®
APPROX. CARTON
NET WT.
QTY
1.00
1.04
1.31
1.96
2.94
5.00
6.38
10.25
48
48
36
24
16
12
8
4
BIV-21
®
BRONZE CHECK VALVES ILLUSTRATED INDEX
BRONZE CHECK VALVES
ILLUSTRATED INDEX
NUMERICAL
INDEX
CODE #
125 WSP/200 WOG
Horizontal Swing Check
T-Pattern
125 WSP/200 WOG
Y-Pattern
125 WSP/200 WOG
Y-Pattern PTFE Disc
AKR Code # 04
Size 3/8″ - 4″
(Threaded)
AKYR Code # 22
Size 1/2″ - 4″
( Threaded)
AK125YRT Code # 22T
Size 1/2″ - 2″
( Threaded)
CR Code # 14
Size 3/8″ - 3″
(Solder)
CYR Code # 23
Size 1/2″ - 3″
(Solder)
C125YRT Code #23T
Size 1/2″ - 2″
(Solder)
PAGE
04...............................BIV-23
14...............................BIV-23
19...............................BIV-28
22...............................BIV-24
22T ............................BIV-25
23...............................BIV-24
23T ............................BIV-25
26...............................BIV-26
29...............................BIV-27
30...............................BIV-27
36...............................BIV-26
150 WSP/300 WOG
Y-Pattern
250 WOG
Vertical Lift Check
Silent Type With FPM Disc
AK150YR Code # 29
Size 3/8″ - 3″
(Threaded)
AKAF Code # 36
Size 1/2″ - 2″
( Threaded)
C150YR Code # 30
Size 3/8″ - 3″
(Solder)
CAF Code # 26
Size 1/2″ - 2″
(Solder)
300 WSP/600 WOG
Y-Pattern
AK300YR Code # 19
Size 1/2″ - 2″
(Threaded)
BIV-22
®
CHECK
CLASS 125 BRONZE
Screw Cap • Integral Seat • Horizontal Swing Type Disc
T-Pattern
BRONZE CHECK
CODE # 04 (AKR)
THREADED
STANDARDS
END TO END
THREADED ENDS
SOLDER JOINT ENDS
DESIGN
KITZ
ANSI B1.20.1
ANSI B16.18
MSS SP-80, Type 3
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
4
17
18
NAME OF PART
SPECIFICATION
BODY
CAP (3/8 – 3)
(4)
DISC (3/8 – 3)
(4)
HINGE PIN
PLUG
CAST BRONZE (B62)
CAST BRONZE (B62)
CAST BRONZE (B62)
FORGED BRASS (B16)
BRASS ROD (B16)
CODE # 14 (CR)
SOLDER*
d2
SIZE
H
L
L1
3/8
1.54
1.54
1.77
2.05
2.44
2.64
3.11
3.58
4.02
4.69
2.09
2.36
2.76
3.15
3.62
4.02
4.80
5.91
6.50
7.68
–
1.64
1.88
2.31
2.83
3.21
4.02
4.69
5.42
–
1/2
3/4
1
11/4
11/2
2
21/2
3
4
®
d1
Max. Min.
.506
.631
.881
1.132
1.382
1.633
2.133
2.633
3.133
–
.502
.627
.877
1.128
1.378
1.628
2.128
2.628
3.128
–
APPROX. CARTON
NET WT.
QTY
0.53
0.68
1.00
1.54
2.33
3.00
4.92
7.75
10.33
16.00
96
96
60
48
24
18
12
8
6
4
BIV-23
CHECK
CLASS 125 BRONZE
BRONZE CHECK
Screw Cap • Integral Seat
Y-Pattern Swing Type Disc
CODE # 22 (AKYR)
THREADED
STANDARDS
END TO END
THREADED ENDS
SOLDER JOINT ENDS
DESIGN
MILITARY
KITZ
ANSI B1.20.1
ANSI B16.18
MSS SP-80, TYPE 3
MSS SP-80, TYPE 3
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
4
17
18
NAME OF PART
SPECIFICATION
BODY
CAP
DISC
HINGE PIN
PLUG
COPPER
BRASS ROD (B16)
CODE # 23 (CYR)
SOLDER*
BIV-24
d2
SIZE
H
L
L1
1/2
1.57
1.93
2.28
2.80
3.15
3.74
4.49
5.16
2.20
2.76
3.15
3.74
4.33
5.04
6.14
7.24
1.64
1.88
2.31
2.83
3.21
4.02
4.69
5.42
3/4
1
11/4
11/2
2
21/2
3
d1
Max. Min.
.631
.881
1.132
1.382
1.633
2.133
2.633
3.133
.627
.877
1.128
1.378
1.628
2.128
2.628
3.128
APPROX. CARTON
NET WT.
QTY
0.52
0.88
1.33
2.04
2.78
4.58
7.67
11.00
96
60
48
24
18
12
6
4
®
CHECK
CLASS 125 BRONZE
Screw Cap • Integral Seat • PTFE Disc
Y-Pattern Swing Type
BRONZE CHECK
CODE # 22T (AKYRT)
THREADED
STANDARDS
END TO END
THREADED ENDS
SOLDER JOINT ENDS
DESIGN
MILITARY
KITZ
ANSI B1.20.1
ANSI B16.18
MSS SP-80, TYPE 4
MSS SP-80, TYPE 4
- FLUID TO 406º
MATERIAL LIST
NO.
1
2
4
12
13
17
18
NAME OF PART
SPECIFICATION
BODY
CAP
DISC
DISC HOLDER
DISC NUT (1/2 ~ 1)
(11/4 ~ 2)
HINGE PIN
PLUG
PTFE
CAST BRONZE (B62)
BRASS ROD (B16)
COPPER
BRASS ROD (B16)
CODE # 23T (CYRT)
SOLDER*
d2
SIZE
H
L
L1
1/2
1.57
1.93
2.28
2.80
3.15
3.74
2.20
2.76
3.15
3.74
4.33
5.04
1.64
1.88
2.31
2.83
3.21
4.02
3/4
1
11/4
11/2
2
®
d1
Max. Min
.631
.881
1.132
1.382
1.633
2.133
.627
.877
1.128
1.378
1.628
2.128
APPROX. CARTON
NET WT.
QTY
0.53
0.89
1.30
1.87
2.70
4.14
96
60
48
24
18
12
BIV-25
CHECK
250 WOG BRONZE
BRONZE CHECK
Silent Type • Spring Loaded Vertical Lift Check
Renewable FPM disc
CODE # 36 (AKAF)
THREADED
STANDARDS
END TO END
THREADED ENDS
SOLDER JOINT ENDS
DESIGN
KITZ
ANSI B1.20.1
ANSI B16.18
KITZ
175 PSI @ 176ºF - MAX. PRESSURE/TEMP. RATING
MATERIAL LIST
NO.
NAME OF PART
SPECIFICATION
1
2
4
12
124
BODY
CAP
DISC
DISC HOLDER
SPRING
FPM
PHOSPHOR BRONZE
CODE # 26 (CAF)
SOLDER*
d2
SIZE
L
L1
1/2
2.09
2.32
2.64
3.07
3.31
3.86
1.40
1.50
1.68
1.88
2.15
2.52
3/4
1
11/4
11/2
2
d1
Max. Min.
.631
.881
1.132
1.382
1.633
2.133
.627
.877
1.128
1.378
1.628
2.128
APPROX. CARTON
NET WT.
QTY
0.38
0.56
0.86
1.25
1.78
2.88
160
96
72
48
36
24
Note: Cracking pressure all sizes 2.85 PSI.
BIV-26
®
CHECK
CLASS 150 BRONZE
Y-Pattern Swing Check • Integral Seat
Swing Type Disc
BRONZE CHECK
CODE # 29 (AK150YR)
THREADED
STANDARDS
END TO END
THREADED ENDS
SOLDER JOINT ENDS
DESIGN
MILITARY
KITZ
ANSI B1.20.1
ANSI B16.18
MSS SP-80, TYPE 3
MSS SP-80, TYPE 3
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
4
13
17
18
69
NAME OF PART
SPECIFICATION
BODY
CAP
DISC
DISC NUT
HINGE PIN
PLUG
ARM
BRASS ROD (B16)
COPPER
BRASS ROD (B16)
CODE # 30 (C150YR)
SOLDER*
d2
SIZE
H
L
L1
3/8
1.54
1.54
1.93
2.28
2.76
3.11
3.74
4.49
5.20
2.13
2.36
2.83
3.31
3.90
4.45
5.16
6.38
7.32
1.64
1.64
1.89
2.31
2.82
3.21
4.01
4.70
5.42
1/2
3/4
1
11/4
11/2
2
21/2
3
®
d1
Max. Min.
.506
.631
.881
1.132
1.382
1.633
2.133
2.633
3.133
.502
.627
.877
1.128
1.378
1.628
2.128
2.628
3.128
APPROX. CARTON
NET WT.
QTY
0.44
0.54
1.00
1.25
2.00
2.81
5.13
12.50
16.00
96
80
48
36
24
16
8
4
3
BIV-27
CHECK
CLASS 300 BRONZE
BRONZE CHECK
Y-Pattern Swing Check • Integral Seat
Swing Type Disc
CODE # 19 (AK300YR)
THREADED
STANDARDS
END TO END
THREADED ENDS
DESIGN
MILITARY
KITZ
ANSI B1.20.1
MSS SP-80, TYPE 3
MSS SP-80, TYPE 3
- FLUID TO 550ºF
MATERIAL LIST
NO.
1
2
4
13
17
18
69
NAME OF PART
SPECIFICATION
BODY
CAP
DISC
DISC NUT
HINGE PIN
PLUG
ARM
BRASS ROD (B16)
COPPER
BRASS ROD (B16)
d2
SIZE
H
L
1/2
1.65
2.01
2.40
2.91
3.27
3.86
2.36
2.83
3.31
3.90
4.45
5.16
3/4
1
11/4
11/2
2
BIV-28
APPROX. CARTON
NET WT.
QTY
0.76
1.15
1.78
3.00
3.94
6.25
80
48
36
24
16
8
®
CAST IRON VALVES
1
Functionally designed handwheel for easy
gripping and operation.
2
Gland bolt made of carbon steel resistant to
breaking and bending under high tightening
stress.
3
4
1
2
Stuffing box of ample depth filled with non
asbestos packing to completely eliminate
leakage around the stem.
3
4
5
Sturdy bonnet, designed to withstand high
internal pressure.
5
Bonnet bolt and nut made of carbon steel of
high tensile strength.
6
Stem made of brass for I.B.B.M., and of 403
stainless steel for 13Cr mounted.
7
Body and disc seat rings are either made of
bronze or 13Cr stainless steel.
8
Flange dimensions conform to ANSI B16.1.
9
Face-to-face dimensions conform to ANSI
B16.10.
®
6
7
8
9
BIV-29
CAST IRON VALVES
KITZ Iron Valves are manufactured in an integrated valve works exclusively devoted to all valve
manufacturing phases such as casting, machining, and assembling, under rigorous quality control. As the
performance of iron valves depends greatly on the quality of the castings, we carefully control the
quality of molten iron with the most advanced casting facilities and quality control. KITZ Iron Valves
are widely used in building piping systems, water treatment plants, and industrial facilities.
®
CAST IRON VALVE ILLUSTRATED INDEX
CAST IRON VALVES
ILLUSTRATED INDEX
NUMERICAL
INDEX
CODE #
125 WSP/200 WOG
OS & Y
Bronze Mounted
125 WSP/200 WOG
OS & Y
Cr 13 Mounted
125 WSP/200 WOG
Non-Rising Stem
Bronze Mounted
125 FCL Code # 72
Size 2″ - 14″
(Flanged)
125FCLS # 73
Size 2″ - 14″
(Flanged)
125FCWI Code # 75
Size 2″ - 12″
(Flanged)
125 WSP/200 WOG
OS & Y
Bronze Mounted
125 WSP/200 WOG
OS & Y
Cr13 Mounted
125FCJ Code # 76
Size 2″ - 8″
(Flanged)
125FCJS Code # 77
Size 2″ - 8″
(Flanged)
125 WSP/200 WOG
Bronze Mounted
125 WSP/200 WOG
Cr 13 Mounted
125 FCO Code # 78
Size 2″ - 10″
(Flanged)
125FCOS Code # 79
Size 2″ - 10″
(Flanged)
PAGE
G
72.................................BIV-31 A
73.................................BIV-32 T
75.................................BIV-33 E
76.................................BIV-34
77.................................BIV-35
78.................................BIV-36
79.................................BIV-37
G
L
O
B
E
C
H
E
C
K
BIV-30
®
GATE
CLASS 125 CAST IRON
Outside Screw & Yoke • Bolted Bonnet
Bronze Mounted • Solid Wedge Disc
END TO END
END CONNECTION
DESIGN
MILITARY
ANSI B16.10, CLASS 125
MSS SP-70, TYPE I
MSS SP-70, TYPE I
- FLUID TO 406ºF
150 PSI NON-SHOCK COLD WATER, OIL OR GAS (14" only)
MATERIAL LIST
NO.
1
2
3
4
7
8
9
10
16
19
30
33
34
35
36
42
43
61
62
63
66
NAME OF PART
SPECIFICATION
BODY
BONNET
STEM
DISC
GLAND
GLAND PACKING
HAND WHEEL (2 – 10)
(12 – 14)
WHEEL NUT
NAME PLATE
GASKET
BODY SEAT RING
BONNET NUT
GLAND NUT
BONNET BOLT
GLAND BOLT
YOKE SLEEVE
WHEEL WASHER
YOKE (10-14)
YOKE NUT (10-14)
YOKE BOLT (10-14)
DISC SEAT RING
CAST IRON (A126 CLASS B)
DUCTILE IRON (A395)
NON-ASBESTOS PACKING
DUCTILE IRON (A536)
ALUMINUM
NON ASBESTOS SHEET
CAST BRONZE (B62)
CAST BRONZE (B62)
CAST BRONZE (B62)
CAST BRONZE (B62)
®
B O LT H O L E
C No.
h
d2
SIZE
d
H
D1
L
l
D
BOLT
SIZE
t
APPROX.
NET WT.
2
1.97
12.91
6.30
7.00
2.28
6.00
4.75
4
21/2
.75
5/8
.62
33
2.56
15.04
6.69
7.50
2.87
7.00
5.50
3
3.15
17.17
6.69
8.00
3.50
7.50
6.00
4
.75
5/8
.69
43
4
.75
5/8
.75
4
3.94
20.94
8.86
9.00
4.29
9.00
53
7.50
8
.75
5/8
.94
5
4.92
24.69
8.86
10.00
5.35
10.00
81
8.50
8
.88
3/4
.94
116
6
5.91
28.58
9.84
10.50
6.34
8
7.87
36.18
11.02
11.50
8.39
11.00
9.50
8
.88
3/4
1.00
157
13.50
11.75
8
.88
3/4
1.12
10
9.84
44.65
13.78
13.00
10.43
244
16.00
14.25 12
1.00
7/8
1.19
394
12
11.81
53.66
17.72
14.00
12.36
19.00
17.00 12
1.00
7/8
1.25
541
14
13.39
61.40
19.69
15.00
14.17
21.00
18.75 12
1.12
1
1.38
755
BIV-31
CAST IRON GATE
STANDARDS
CODE # 72 (125FCL)
GATE
CLASS 125 CAST IRON
CAST IRON GATE
13 Cr Mounted • Solid Wedge Disc
CODE # 73 (125FCLS)
STANDARDS
END TO END
END CONNECTION
DESIGN
MILITARY
MSS SP-70, TYPE I
MSS SP-70, TYPE I
- FLUID TO 406ºF
150 PSI NON-SHOCK COLD WATER, OIL OR GAS (14" only)
MATERIAL LIST
NO.
1
2
3
4
7
8
9
10
16
19
30
33
34
35
36
42
43
61
62
63
66
NAME OF PART
SPECIFICATION
BODY
BONNET
STEM
DISC
GLAND
GLAND PACKING
(12 & 14)
WHEEL NUT
NAME PLATE
GASKET
BODY SEAT RING
BONNET NUT
GLAND NUT
BONNET BOLT
GLAND BOLT
YOKE SLEEVE
WHEEL WASHER
YOKE (10 – 14)
YOKE NUT (10 – 14)
YOKE BOLT (10 – 14)
DISC SEAT RING
CAST IRON (A126 CASS. B)
DUCTILE IRON (A395)
DUCTILE IRON (A536)
ALUMINUM
NON ASBESTOS SHEET
STAINLESS STEEL (A182 Gr. F6a)
CAST BRONZE (B62)
CAST BRONZE (B62)
STAINLESS STEEL (B182 Gr. F6a)
BIV-32
d2
SIZE
d
H
D1
L
l
D
B O LT H O L E
C No.
h
BOLT
SIZE
t
APPROX.
NET WT.
2
1.97
12.91
6.30
7.00
2.28
6.00
4.75
4
.75
5/8
.62
33
21/2
2.56
15.04
6.69
7.50
2.87
7.00
5.50
4
.75
5/8
.69
43
3
3.15
17.17
6.69
8.00
3.50
7.50
6.00
4
.75
5/8
.75
53
4
3.94
20.94
8.86
9.00
4.29
9.00
7.50
8
.75
5/8
.94
81
5
4.92
24.69
8.86
10.00
5.35
10.00
8.50
8
.88
3/4
.94
116
6
5.91
28.58
9.84
10.50
6.34
11.00
9.50
8
.88
3/4
1.00
157
8
7.87
36.18
11.02
11.50
8.39
13.50
11.75
8
.88
3/4
1.12
244
10
9.84
44.65
13.78
13.00
10.43
16.00
14.25 12
1.00
7/8
1.19
394
12
11.81
53.66
17.72
14.00
12.36
19.00
17.00 12
1.00
7/8
1.25
541
14
13.39
61.40
19.69
15.00
14.17
21.00
18.75 12
1.12
1
1.38
755
®
GATE
CLASS 125 CAST IRON
Non-Rising Stem • Bolted Bonnet with Open/Close Indicator
Bronze Mounted • Solid Wedge Disc
CAST IRON GATE
STANDARDS
CODE # 75 (125FCWI)
END TO END
END CONNECTION
DESIGN
MILITARY
MSS SP-70, TYPE I
MSS SP-70, TYPE I
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
3
4
7
8
9
10
16
19
30
33
34
35
36
38
39
64
66
97
98
99
NAME OF PART
SPECIFICATION
BODY
BONNET
STEM
DISC
GLAND
GLAND PACKING
HAND WHEEL
WHEEL NUT
NAME PLATE
GASKET
BODY SEAT RING
BONNET NUT
GLAND NUT
BONNET BOLT
GLAND BOLT
BONNET BUSH
SET PIN (8 – 12)
STEM NUT
DISC SEAT RING
INDICATOR
PLATE
SET BOLT
DUCTILE IRON (A395)
ALUMINUM
NON ASBESTOS SHEET
CAST BRONZE (B62)
CAST BRONZE (B62)
CARBON STEEL
CAST BRONZE (B62)
CAST BRONZE (B62)
ZINC DIE-CAST (B85)
ALUMINUM
®
d2
SIZE
d
H
D1
L
l
D
B O LT H O L E
C No.
h
BOLT
SIZE
t
APPROX.
NET WT.
2
1.97
9.84
5.51
7.00
2.36
6.00
4.75
4
.75
5/8
.62
39
21/2
2.56
11.22
6.30
7.50
2.95
7.00
5.50
4
.75
5/8
.69
50
3
3.15
13.78
6.30
8.00
3.58
7.50
6.00
4
.75
5/8
.75
59
4
3.94
15.75
7.09
9.00
4.41
9.00
7.50
8
.75
5/8
.94
90
5
4.92
18.31
8.86
10.00
5.39
10.00
8.50
8
.88
3/4
.94
128
6
5.91
20.28
8.86
10.50
6.30
11.00
9.50
8
.88
3/4
1.00
174
8
7.87
24.80
11.81
11.50
8.39
13.50
11.75
8
.88
3/4
1.12
260
10
9.84
29.92
13.78
13.00
10.39
16.00
14.25 12
1.00
7/8
1.19
416
12
11.81
34.25
13.78
14.00
12.60
19.00
17.00 12
1.00
7/8
1.25
581
BIV-33
GLOBE
CLASS 125 CAST IRON
CAST IRON GLOBE
Bronze Mounted • Beveled Wedge Disc
CODE # 76 (125FCJ)
STANDARDS
END TO END
END CONNECTION
DESIGN
MILITARY
MSS SP-85, TYPE I
MSS SP-85, TYPE I
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
3
4
5
7
8
9
10
16A
19
30
33
34
35
36
37
40
66
NAME OF PART
SPECIFICATION
BODY
BONNET
STEM
DISC (2)
(21/2 – 8)
LOCK NUT
GLAND
GLAND PACKING
(8)
WHEEL NUT
NAME PLATE
GASKET
BODY SEAT RING
BONNET NUT
GLAND NUT
BONNET BOLT
GLAND BOLT
YOKE BUSH
LOCK PLATE
DISC SEAT RING
CAST BRONZE (B62)
CAST BRONZE (B62)
DUCTILE IRON (A395)
DUCTILE IRON (A536)
ALUMINUM
NON ASBESTOS SHEET
CAST BRONZE (B62)
CAST BRONZE (B62)
CAST BRONZE (B62)
d2
SIZE
BIV-34
d
H
D1
L
l
D
B O LT H O L E
C No.
h
BOLT
SIZE
t
APPROX.
NET WT.
2
1.97
10.91
7.09
8.00
.79
6.00
4.75
4
.75
5/8
.62
30
21/2
2.56
12.09
7.09
8.50
1.02
7.00
5.50
4
.75
5/8
.69
46
3
3.15
13.90
8.86
9.50
1.18
7.50
6.00
4
.75
5/8
.75
66
4
3.94
15.91
11.02
11.50
1.50
9.00
7.50
8
.75
5/8
.94
92
5
4.92
17.87
11.81
13.00
1.81
10.00
8.50
8
.88
3/4
.94
141
6
5.91
20.98
13.78
14.00
2.28
11.00
9.50
8
.88
3/4
1.00
197
8
7.87
25.28
17.72
19.50
2.91
13.50
11.75
8
.88
3/4
1.12
323
®
GLOBE
CLASS 125 CAST IRON
13 Cr Mounted • Beveled Wedge Disc
CAST IRON GLOBE
CODE # 77 (125FCJS)
STANDARDS
END TO END
END CONNECTION
DESIGN
MILITARY
MSS SP-85, TYPE I
MSS SP-85, TYPE I
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
3
4
5
7
8
9
10
16A
16B
19
30
33
34
35
36
37
40
66
NAME OF PART
SPECIFICATION
BODY
BONNET
STEM
DISC (2)
(21/2 – 8)
LOCK NUT (2 – 4)
(5 – 8)
GLAND
GLAND PACKING
(8)
WHEEL NUT
NAME PLATE
WASHER
GASKET
BODY SEAT RING
BONNET NUT
GLAND NUT
BONNET BOLT
GLAND BOLT
YOKE BUSH
LOCK PLATE
DISC SEAT RING
STAINLESS STEEL (A743 Gr. CA-15)
DUCTILE IRON (A395)
DUCTILE IRON (A536)
ALUMINUM
CARBON STEEL (A36)
NON ASBESTOS SHEET
CAST BRONZE (B62)
®
d2
SIZE
d
H
D1
L
l
D
B O LT H O L E
C No.
h
BOLT
SIZE
t
APPROX.
NET WT.
2
1.97
10.91
7.09
8.00
.79
6.00
4.75
4
.75
5/8
.62
30
21/2
2.56
12.09
7.09
8.50
1.02
7.00
5.50
4
.75
5/8
.69
46
3
3.15
13.90
8.86
9.50
1.18
7.50
6.00
4
.75
5/8
.75
66
4
3.94
15.91
11.02
11.50
1.50
9.00
7.50
8
.75
5/8
.94
92
5
4.92
17.87
11.81
13.00
1.81
10.00
8.50
8
.88
3/4
.94
141
6
5.91
20.98
13.78
14.00
2.28
11.00
9.50
8
.88
3/4
1.00
197
8
7.87
25.28
17.72
19.50
2.91
13.50
11.75
8
.88
3/4
1.12
323
BIV-35
SWING CHECK
CLASS 125 CAST IRON
CAST IRON SWING CHECK
Bolted Cover • Bronze Mounted
Swing Type Disc
STANDARDS
END TO END
END CONNECTION
DESIGN
MILITARY
CODE # 78 (125FCO)
MSS SP-71, TYPE I
MSS SP-71, TYPE I
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
4
13
14
16
17
18
19
30
33
35
44
66
69
70
71
124
NAME OF PART
SPECIFICATION
BODY
COVER
DISC (2 – 4)
(5 – 10)
DISC NUT
SPLIT PIN
NAME PLATE
HINGE PIN
PLUG
GASKET
BODY SEAT RING
COVER NUT
COVER BOLT
GASKET
DISC SEAT RING
ARM
WASHER
DISC BOLT
SPRING PIN
CAST BRONZE (B62)
STAINLESS STEEL (A580 Type 304)
ALUMINUM
CARBON STEEL (A36)
NON ASBESTOS SHEET
CAST BRONZE (B62)
NON ASBESTOS SHEET
CAST BRONZE (B62)
DUCTILE IRON (A536 Gr.60-40-18)
CARBON STEEL (A36)
CARBON STEEL (A686 Type W1)
d2
SIZE
BIV-36
d
H
L
D
B O LT H O L E
C No.
h
BOLT
SIZE
t
APPROX.
NET WT.
2
1.97
4.37
8.00
6.00
4.75
4
.75
5/8
.62
24
21/2
2.56
4.76
8.50
7.00
5.50
4
.75
5/8
.69
38
3
3.15
5.71
9.50
7.50
6.00
4
.75
5/8
.75
47
4
3.94
6.50
11.50
9.00
7.50
8
.75
5/8
.94
66
5
4.92
8.15
13.00
10.00
8.50
8
.88
3/4
.94
111
6
5.91
8.86
14.00
11.00
9.50
8
.88
3/4
1.00
153
8
7.87
10.55
19.50
13.50
11.75
8
.88
3/4
1.12
251
10
9.84
12.40
24.50
16.00
14.25 12
1.00
7/8
1.19
396
®
SWING CHECK
CLASS 125 CAST IRON
Bolted Cover • 13 Cr. Mounted
Swing Type Disc
END TO END
END CONNECTION
DESIGN
MILITARY
CODE # 79 (125FCOS)
MSS SP-71, TYPE I
MSS SP-71, TYPE I
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
4
13
14
16
17
18
19
30
33
35
44
66
69
70
71
124
NAME OF PART
SPECIFICATION
BODY
COVER
DISC (2 – 4)
(5 – 10)
DISC NUT
SPLIT PIN
NAME PLATE
HINGE PIN
PLUG
GASKET
BODY SEAT RING
COVER NUT
COVER BOLT
GASKET
DISC SEAT RING
ARM
WASHER
DISC BOLT
SPRING PIN
STAINLESS STEEL (A580 Type 304
ALUMINUM
CARBON STEEL (A36)
NON ASBESTOS SHEET
NON ASBESTOS SHEET
DUCTILE IRON (A536 Gr. 60-40-18)
CARBON STEEL (A36)
CARBON STEEL (A686 Type W1)
d2
SIZE
®
BIV-37
d
H
L
D
B O LT H O L E BOLT
C No.
h
SIZE
t
APPROX.
NET WT.
2
1.97
4.37
8.00
6.00
4.75
4
.75
5/8
.62
24
21/2
2.56
4.76
8.50
7.00
5.50
4
.75
5/8
.69
38
3
3.15
5.71
9.50
7.50
6.00
4
.75
5/8
.75
47
4
3.94
6.50
11.50
9.00
7.50
8
.75
5/8
.94
66
5
4.92
8.15
13.00
10.00
8.50
8
.88
3/4
.94
111
6
5.91
8.86
14.00
11.00
9.50
8
.88
3/4
1.00
153
8
7.87
10.55
19.50
13.50
11.75
8
.88
3/4
1.12
251
10
9.84
12.40
24.50
16.00
14.25 12
1.00
7/8
1.19
396
BIV-37
CAST IRON SWING CHECK
STANDARDS
KITZ Stainless Steel Valves are designed for use within the chemical industry. Extensive factory testing
is carried out at each step of the integrated production process — beginning with raw materials selection
and the unique KITZ casting process and ending with finishing of the service-ready product. The
special attention given to production, testing and quality control make KITZ Stainless Steel Valves a
reliable choice for the process industries.
1
“Sure Grip” Handwheel - for easy operation.
2
Non-rising Stem is made of Type 316
stainless steel and has a construction that
makes it particularly suitable for installation
where head space is limited.
1
2
3
3
4
5
6
BIV-38
Hex Head Packing Nut can be easily
loosened or tightened and packing
replacement is a simple task.
4
Deep Stuffing Box allows the use of generous
packing to assure positive stem sealing.
5
Body and Bonnet are made of ASTM CF8M
by investment casting. The design and
workmanship not only economize on
maintenance, they assure a long service life in
a wide range of industrial applications.
6
The disc and integral seat are tapered to
extreme precision to provide leak-tight
sealing. The guide channels are beveled at
the top of the body for correct alignment and
easy assembly.
®
®
STAINLESS STEEL (316/CF8M) VALVES
ILLUSTRATED INDEX
CODE #
STAINLESS STEEL (316/CF8M) VALVES ILLUSTRATED INDEX
STAINLESS STEEL GATE
Non-Rising Stem
200 WOG
NUMERICAL
INDEX
STAINLESS STEEL GLOBE
Non-Rising Stem
200 WOG
PAGE
31.................................BIV-40
33.................................BIV-41
34.................................BIV-42
G
L
O
B
E
G
A
T
E
AKUELM Code # 31
Size 1/2″ - 4″
(Threaded)
AKUJM Code # 33
Size 3/8″ - 3″
(Threaded)
STAINLESS STEEL CHECK
Swing Type Disc
200 WOG
C
H
E
C
K
AKUOM Code # 34
Size 1/2″ - 3″
(Threaded)
®
BIV-39
GATE
200 WOG STAINLESS STEEL
STAINLESS STEEL GATE
Screw-In-Bonnet • Inside Screw • Non-Rising Stem
Stainless Steel Disc
CODE # 31 (AKUELM) 1/2 - 2
(AKUEM) 21/2 - 4
THREADED
STANDARDS
END TO END
THREADED ENDS
WALL THICKNESS
DESIGN
KITZ
ANSI B1.20.1
KITZ
KITZ
200 PSIG @ 250ºF – STATIC FLUID
150 PSIG @ 250°F – PULSATING FLUID / GAS
120 PSIG @ 350°F – SATURATED STEAM
MATERIAL LIST
NO.
1
2
3
4
6
7
8
9
10
16
31
48
NAME OF PART
SPECIFICATION
BODY
BONNET
STEM
DISC
PACKING NUT
GLAND
GLAND PACKING
(1 – 2)
(21/2)
(3 – 4)
WHEEL NUT
NAME PLATE
STEM WASHER
SNAP RING
STAINLESS STEEL (A351 Gr. CF8M)
ARAMID FIBERS WITH GRAPHITE
ZINC DIE-CAST (B86)
DUCTILE IRON (A536)
ALUMINUM
STAINLESS STEEL
d2
SIZE
H
D1
L
1/2
3.78
3.98
4.41
4.84
5.91
6.57
9.76
10.83
12.40
2.76
2.76
3.15
3.15
3.94
3.94
5.31
6.10
7.87
2.13
2.28
2.56
2.91
3.07
3.43
4.53
5.12
6.10
3/4
1
11/4
11/2
2
21/2
3
4
BIV-40
APPROX. CARTON
NET WT.
QTY
1.35
1.69
2.21
3.19
6.17
8.13
16.25
20.00
32.00
48
32
24
16
12
8
4
3
1
®
GLOBE
Stainless Steel Disc
STAINLESS STEEL GLOBE
CODE # 33 (AKUJM)
THREADED
STANDARDS
END TO END
THREADED ENDS
WALL THICKNESS
DESIGN
KITZ
ANSI B1.20.1
KITZ
KITZ
MATERIAL LIST
NO.
NAME OF PART
SPECIFICATION
1
2
3
4
5
6
BODY
BONNET
STEM
DISC
LOCK NUT
PACKING NUT
7
8
9
GLAND
GLAND PACKING
(1 – 3)
WHEEL NUT
BONNET RING
NAME PLATE
GASKET
PACKING WASHER
LOCK PLATE
or (A351 Gr. CF8)
ARAMID FIBERS WITH GRAPHITE
ZINC DIE-CAST (B86)
ALUMINUM
ARAMID FIBER SHEET
STAINLESS STEEL
10
11
16
19
20
40
d2
SIZE
H
D1
L
3/8
4.29
4.37
4.41
5.59
5.91
6.73
7.44
9.96
11.02
2.36
2.36
2.76
3.54
3.54
3.94
4.53
7.09
8.86
2.17
2.56
3.15
3.54
4.13
4.72
5.51
7.09
7.87
1/2
3/4
21/2 and Larger
®
1
11/4
11/2
2
21/4
3
APPROX. CARTON
NET WT.
QTY
1.31
1.44
2.06
3.04
4.33
6.25
9.83
14.67
21.50
48
48
30
24
15
12
6
3
2
BIV-41
SWING CHECK
STAINLESS STEEL SWING CHECK
Integral Seat • Threaded Cap
Swing Type Disc
CODE # 34 (AKUOM)
STANDARDS
END TO END
THREADED ENDS
WALL THICKNESS
DESIGN
KITZ
ANSI B1.20.1
KITZ
KITZ
MATERIAL LIST
NO.
NAME OF PART
SPECIFICATION
1
BODY
2
CAP
4
17
18
44
DISC
HINGE PIN
PLUG
GASKET
or (A182 Gr. F316)
ARAMID FIBER SHEET GASKET
d2
SIZE
H
L
1/2
1.77
2.17
2.40
2.80
2.83
3.19
3.66
4.09
2.56
3.15
3.54
4.13
4.72
5.51
7.09
7.87
3/4
1
11/4
11/2
2
21/4
3
BIV-42
APPROX. CARTON
NET WT.
QTY
0.94
1.44
2.06
3.05
4.31
6.33
13.25
15.50
72
48
32
20
16
9
4
2
®
®
BRONZE & CAST IRON STRAINERS
ILLUSTRATED INDEX
CODE #
BRONZE & CAST IRON STRAINERS ILLUSTRATED INDEX
BRONZE STRAINERS
Y-Pattern
304 S.S. Punched Screen
150 WSP/300 WOG
NUMERICAL
INDEX
PAGE
15.................................BIV-44
16.................................BIV-44
80.................................BIV-45
AKYU Code # 15
Size 1/4″ - 2″
(Threaded)
CYU Code # 16
Size 1/2″ - 2″
(Solder)
IRON STRAINERS
Y-Pattern
304 S.S. Punched Screen
125 WSP/200 WOG
125FCYU Code # 80
Size 2″ - 12″
(Flanged)
®
BIV-43
STRAINER
CLASS 150 BRONZE
BRONZE STRAINER
Y-Pattern • Threaded Cap and Ends
Stainless Steel (304) Punched Screen
CODE # 15 (AKYU)
THREADED
STANDARDS
END TO END
THREADED ENDS
SOLDER JOINT ENDS
WALL THICKNESS
DESIGN
KITZ
ANSI B1.20.1
ANSI B16.18
KITZ
KITZ
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
19
27
NAME OF PART
SPECIFICATION
BODY
* CAP
GASKET
SCREEN
NON-ASBESTOS SHEET
* Cap supplied without plug. Blind cap optionally available.
CODE # 16 (CYU)
SOLDER*
d2
SIZE
H
L
P
L1
1/4
1.73
1.73
1.93
2.28
2.80
3.19
3.82
4.72
5.83
7.09
2.76
2.76
3.15
3.94
4.53
5.31
6.30
7.68
9.06
9.45
1/4
–
–
2.15
2.63
3.10
3.77
4.51
5.59
–
–
3/8
1/2
3/4
d1
1
11/4
11/2
2
21/2
3
1/4
1/4
1/4
1/2
1/2
3/4
1
11/4
11/2
d1
Max. Min.
–
.506
.631
.881
1.132
1.382
1.633
2.133
2.633
3.133
–
.502
.627
.877
1.128
1.378
1.628
2.128
2.628
3.128
APPROX. CARTON
NET WT.
QTY
0.56
0.56
0.76
1.29
1.86
2.92
4.31
7.25
13.00
19.00
96
96
80
48
36
24
16
8
1
1
NOTE: The standard punched screen is approximately 12 mesh screen. Other
mesh screens are available (see spare parts in price sheet).
NOTE: NOT INTENDED FOR USE IN A POTABLE WATER SYSTEM - COMPLIANT STATEMENT
PROP 65, STATE OF CALIFORNIA
BIV-44
®
STRAINER
CLASS 125 IRON
Y-Pattern • Bolted Cover • Blow-Out-Plug
Stainless Steel (304) Screen
IRON STRAINER
CODE # 80 (125FCYU)
STANDARDS
END TO END
THREADED ENDS
WALL THICKNESS
DESIGN
KITZ
KITZ
KITZ
- FLUID TO 406ºF
MATERIAL LIST
NO.
1
2
19
27
33
34
35
36
NAME OF PART
SPECIFICATION
BODY
COVER
GASKET
SCREEN
COVER NUT (2 - 6) (1S)
COVER HINGE NUT
COVER BOLT (2 - 6) (1S)
(8 - 12)
COVER HINGE BOLT
NON-ASBESTOS SHEET
CARBON STEEL (A307 GR. B)
STAINLESS STEEL (A194 GR. B8)
CARBON STEEL (A307 GR. B)
1S = 1 Set
8 & Larger
®
d2
SIZE
d
L
H
2
21/2
1.97
9.84
2.56
11.22
B O LT H O L E
C No.
h
H1
D
P
6.61
8.58
6.00
1/2
4.75
4
8.35
11.22
7.00
1/2
5.50
4
BOLT
SIZE
t
APPROX.
NET WT.
.75
5/8
.62
30
.75
5/8
.68
50
77
3
3.15
12.40
9.53
13.39
7.50
1/2
6.00
4
.75
5/8
.75
4
3.94
14.57
11.18
15.39
9.00
1/2
7.50
8
.75
5/8
.94
76
5
4.92
16.54
12.80
17.72
10.00
1/2
8.50
8
.87
3/4
.94
126
6
5.91
19.29
14.57
19.76
11.00
3/4
9.50
8
.87
3/4
1.00
171
11.75
242
8
7.87
22.44
17.32
23.35
13.50
3/4
8
.87
3/4
1.12
10
9.84
26.77
20.28
27.48
16.00
1
14.25 12
.98
7/8
1.18
411
12
11.81
31.50
23.62
32.40
19.00
1
17.00 12
.98
7/8
1.25
561
BIV-45
®
ENGINEERING DATA INDEX
ENGINEERING DATA
Page
Valve Terms &
Piping Symbols . . . . . . . . . . . . .BIV-47
Referenced Specifications &
Design Standards . . . . . . . . . . .BIV-48
Dezincification . . . . . . . . . . . . .BIV-49
Page
Page
Cv Valves . . . . . . . . . . . . . . . . .BIV-54
Conversion Tables . . . . . . . . . .BIV-62
Saturated Steam Table
Pressure Temperature . . . . . . . .BIV-55
Conversion Chart
Fraction-Decimal-Millimeter . .BIV-63
Bronze
Flange Dimensions . . . . . . .BIV-56-57
Temperature Conversion . . . . . .BIV-64
Temperature Limitations
of Materials . . . . . . . . . . . . . . . .BIV-50
Cast Iron
Flange Dimensions . . . . . . . . . .BIV-58
Properties of
Valve Materials . . . . . . . . . . . . .BIV-51
ASME/ANSI Standard Iron Pipe
Taper Threads . . . . . . . . . . . . . .BIV-59
Bronze Valves Seat/Packing
Material Options . . . . . . . . . . . .BIV-52
ASME/ANSI Standard Copper
Water Tube & Solder-Joint
Ends . . . . . . . . . . . . . . . . . . . . .BIV-60
Conversion Chart
Pressure . . . . . . . . . . . . . . . . . . .BIV-65
Weight Conversion . . . . . . . . . .BIV-66
Iron Valves Seat/Packing/
Gasket Material Options . . . . . .BIV-53
BIV-46
Cross Reference Chart . . . . . . .BIV-67
Solder Installation Tips . . . . . . .BIV-61
®
VALVE TERMS AND PIPING SYMBOLS
ABBREVIATIONS USED IN THE VALVE
AND FITTING INDUSTRY
®
American Foundrymen's Society
American Gas Association
American National Std. Institute
American Society of Mechanical Engineers
American Society of Testing & Materials
American Water Works Association
Bolted Bonnet
Butterfly Valve
Brinell Hardness Number
British Thermal Unit
Butt Weld
Butt Weld Ends
Celcius Degrees
Copper to Copper
Copper Development Association
Cast Iron
13% Chromium Stainless Steel
Canadian Standards Association
Double Disc
Ductile Iron
Fahrenheit Degrees
Flanged End
Flat Faced
Factory Mutual Laboratories
Free On Board
Gallons Per Minute
Hydragyrum (Mercury)
Brinell Hardness
Rockwell C Hardness
Iron Body Bronze Mounted
Inside Diameter
Iron Pipe Size
Inside Screw Non-Rising Stem
International Standards Organization
Inside Screw Rising Stem
Manufacturers Standardization Society
Material Test Report
National Pipe Taper (Pipe Thread)
Non-Rising Stem
Outside Diameter
Outside Screw and Yoke
Pressure Nominal (Metric)
Pounds Per Square Inch
Pounds Per Square Inch Absolute
Pounds Per Square Inch Gage
Pressure – Temperature
Rockwell "C"
Raised Face
Revolutions Per Minute
Rising Stem
Screw-In-Bonnet
Screwed Ends
Solder Joint
Stainless Steel
Standard
Steam Working Pressure
Certain Valve Parts – Stems, Seats, Etc.
Union Bonnet
Underwriter's Laboratories
Working Pressure: Water, Oil and Gas
Working Steam Pressure
Water Working Pressure
VALVE SELECTION GUIDE
VALVE TERMS AND PIPING SYMBOLS
AFS
AGA
ANSI
ASME
ASTM
AWWA
BB
BFV
BHN
BTU
BW
BWE
C
CxC
CDA
CI
Cr 13
CSA
DD
DI
F
FE
FF
FM
FOB
GPM
Hg
HB
HRC
IBBM
ID
IPS
ISNRS
ISO
ISRS
MSS
MTR
NPT
NSR
OD
OS&Y
PN
PSI
PSIA
PSIG
P–T
Rc
RF
RPM
RS
SB
SE
SJ
SS
STD
SWP
TRIM
UB
UL
WOG
WSP
WWP
GATE
Recommended for:
• Full Open/Closed Service
• Minimal Line Pressure Drop
• Infrequent Operation
GLOBE
Recommended for:
• Throttling of flow
• Frequent Operation
• Service with some line resistance to flow
• Angle Valves offer less resistance to flow
than valve and elbow.
CHECK
Recommended for:
• Control of direction of flow and quick
automatic reaction to flow change.
• Use in conjunction with gate valve.
– They should not be used in air compressor
service or on a reciprocating pump as these
services will cause chattering and valve
vibration damage.
BIV-47
REFERENCED SPECIFICATIONS AND DESIGN STANDARDS
REFERENCED SPECIFICATIONS
AND DESIGN STANDARDS
KITZ valves are manufactured under strict quality control throughout all stages of production, beginning with
inspection of chemical composition and mechanical properties of materials. Extra care is given to inspection and
testing at all machine shops and assembly plants, utilizing up-to-date precision equipment. All KITZ valves are
subject to strict hydrostatic pressure testing of the body and seat sealing as well as other exhaustive testing to
assure long life service and Quality KITZ Performance.
KITZ valves meet or exceed the following
Standards Practice of the Manufacturers
Standardization Society of Valve and Fitting
Industry:
STANDARD PRACTICE – 80
MSS SP-80
BRONZE GATE, GLOBE, ANGLE AND
CHECK VALVES
MSS SP-70
CAST IRON GATE VALVES, FLANGED
AND THREADED ENDS
MSS SP-85
CAST IRON GLOBE AND ANGLE VALVES,
FLANGED AND THREADED ENDS
MSS SP-71
GRAY IRON SWING CHECK VALVES,
FLANGED AND THREADED ENDS
OTHER RELEVANT STANDARDS:
AMERICAN NATIONAL STANDARDS
INSTITUTE (A.N.S.I.)
STANDARD B1.1
The Unified Screw Thread Standard cover manufacturing tolerances of screw threads.
STANDARD B1.20.1
This standard covers pipe screw threads.
STANDARD B2.4
This standard covers hose coupling screw
threads.
STANDARD 16.18
This standard covers solder cup tolerances.
STANDARD B16.1
This standard covers Class 125/250 Cast Iron
pipe flanges and flanged fittings.
STANDARD B16.10
This standard covers face-to-face and end-toend dimension of ferrous valves.
NOTE: Federal Specifications WW-V-54 and
WW-V-58 were cancelled April 1983 and
replaced with the above Standard Practices.
BIV-48
®
DEZINCIFICATION
Deterioration of water quality and changes in piping materials have amplified valve dezincification problems.
DEZINCIFICATOIN
What is Dezincification?
In a bronze valve, the body, bonnet, and other
bronze cast parts hardly corrode at all due to the
small percentage of zinc in the alloy. Brass parts
with a 40% zinc content (stems in particular) are
subject to extreme dezincification.
The copper alloy used in bronze valves contains
zinc, tin, and lead with copper as a base. When
bronze valves are subjected to unfavorable operating conditions the zinc component contained in the
copper alloy separates from the copper base, and
the metal corrodes. This is called dezincification.
Why Does Dezincification Occur?
3) High electrical conductivity with large
quantities of chlorides and sulfides present.
4) With copper or vinyl chloride pipes.
5) With a large quantity of dissolved oxygen.
The following factors cause dezincification. These
factors are generally believed to occur together,
rather than independently.
1) Aqueous solutions high in acidity.
2) Warm water with a high free carbonic acid
content and high electrical conductivity.
What is K-Metal?
comparisons clearly show K-Metal's overall
superiority and explain why KITZ valves provide
superior performance and give longer life.
Figures 1 through 4 compare "K-Metal" with other
materials. Material manufactured by a competitor
is a dezincification-resistant material.
Corrosion Quantity
Comparison
Fig. 4
Comparison of
Dezincification
Depth
0.01
00
4
B
2
-1
No
r's
"
6
B1
77
3
.C
tito
M
"
al
et
M
K-
M
0
pe
Dezincification Depth (inch)
2
ial
0.02
B6
er
0.03
m
B
.
No
0.04
Co
4
2
-1
6
B1
r's
"
0
70
7
C3
at
"
al
et
tito
2
ial
B6
er
at
0
pe
B
.
No
20
m
4
2
-1
40
M
K-
M
"
6
B1
r's
2
ial
B6
M
K-
0
70
7
C3
60
Co
m
B
er
M
.
No
"
al
et
tito
4
2
-1
r's
"
20
0
6
B1
pe
M
K-
0
70
7
C3
at
"
al
et
tito
0
40
pe
20
60
m
40
80
Co
60
Corrosion Quantity (mg/cm2)
100
Hardness (HRB)
80
Co
Tensile Strength (ksi)
(1mg/cm2=0.014 mlb/in2)
2
Fig. 3
ial
Hardness
Comparison
B6
Fig. 2
Comparison of
Tensile Strength
er
Fig. 1
at
To combat dezincification KITZ developed
"K-Metal," used in the stems of all KITZ brass
valves and any other valves not using Bronze Alloy
B62. The charts below compare K-Metal with
B124, B16, B62, and a competitor's dezincification
material. Compared are tensile strength, corrosion
quantity, hardness, and dezincification. The
(Corrosion quantity and dezincification depth are values recorded after two weeks.)
NOTE:
The dezincification test was based on the Australian Standard AS C316.
Conclusion
By using dezincification-resistant copper-based alloy
"K-Metal", KITZ maintains strict quality control.
®
You can depend on KITZ bronze and brass valves
to be free of corrosion problems.
BIV-49
TEMPERATURE LIMITATIONS OF MATERIALS
TEMPERATURE LIMITATION
OF MATERIALS
PRESSURE/TEMPERATURE RATINGS
FOR GRAY IRON VALVES*
PRESSURE/TEMPERATURE RATINGS FOR
BRONZE PRESSURE RATED VALVES*
PRESSURE
PRESS. CLASS
END CONN.
TEMP.
°F
(1)
125 (2)
THD.
PRESSURE –– PSI
–– PSI
ASTM B-62
ASTM B-61
300
300(3)
THD.
THD.
150
THD.
MATERIAL
-20 TO 150
200
300
600
1000
______________________________________________________________________
200
185
270
560
920
______________________________________________________________________
250
170
240
525
830
______________________________________________________________________
300
155
210
490
740
______________________________________________________________________
350
140
180
450
650
______________________________________________________________________
400
––
––
410
560
______________________________________________________________________
406
125
150
––
––
______________________________________________________________________
145(4)
375
480
450
120(4)
______________________________________________________________________
500
––
––
340
390
______________________________________________________________________
550
––
––
300
300
(1) Refer to pressure/temperature of copper piping systems below.
(2) PTFE Disc materials are limited to 450°F.
(3) Alternative rating for valves sizes 1/8 – 2 having a union ring
body/bonnet joint.
(4) ASME BPVC, Section 1 limits the rated temperature of indicated
materials to 406°F.
* Extracted from MSS-SP-80.
TEMPERATURE
°F
1) 2)
CLASS 125
200 WOG
2"–12"
14"–24"
CLASS 250
500 WOG
2"–12"
14"–24"
-20 TO 150
200
150
500
300
_____________________________________________________________________
200
190
135
460
280
_____________________________________________________________________
225
180
130
440
270
_____________________________________________________________________
250
175
125
415
260
_____________________________________________________________________
275
170
120
395
250
_____________________________________________________________________
300
165
110
375
240
_____________________________________________________________________
325
155
105
355
230
_____________________________________________________________________
350
150
100
335
220
_____________________________________________________________________
375
145
–
315
210
_____________________________________________________________________
400
140
–
290
200
_____________________________________________________________________
425
130
–
270
–
_____________________________________________________________________
125
–
250
–
450 (1)
_____________________________________________________________________
500
–
–
–
–
_____________________________________________________________________
550
–
–
–
–
_____________________________________________________________________
600
–
–
–
–
_____________________________________________________________________
650
–
–
–
–
The temperature shown for the corresponding rating shall be the
metal temperature of the pressure retaining parts. It shall be
assumed that the metal temperature will be the temperature of the
contained fluid. Use of a pressure rating at a metal temperature
other than that of the contained fluid shall be the responsibility of the
user.
(1) Maximum temperature for bronze trim.
* Extracted from MSS-SP-70
RATED WORKING PRESSURES OF JOINTS MADE OF COPPER WATER
TUBE AND SOLDER JOINT VALVES AND FITTINGS, PSI (BAR)
Copper Water Tube K,L and M - Nominal Size: Inch (mm)
SOLDER ALLOY’S
USED IN JOINTS
50-50 Tin-Leadb e
95-5 Tin-Antimonyc
SERVICE
TEMPERATURE
ºF
100
150
200
250
100
150
200
250
ºC
(38)
(66)
(93)
(121)
(38)
(66)
(93)
(121)
WATER
1/4”
200
150
100
85
635
635
630
435
~ 1”
11/4” ~ 2”
(14)
(19)
(9)
(6)
(43)
(43)
(43)
(30)
175
125
90
75
560
560
480
330
(12)
(8)
(6)
(5)
(39)
(39)
(33)
(23)
a
21/2” ~ 4”
150
100
75
50
375
375
375
265
(10)
(7)
(5)
(3)
(26)
(26)
(26)
(18)
5” ~ 8”
135
90
70
45
340
340
340
245
(9)
(6)
(4)
(3)
(23)
(23)
(23)
(16)
10” ~ 12”
100
70
50
40
150
150
140
110
SATURATED
STEAM (All Sizes)
(7)
(4)
(3)
(2)
(10)
(10)
(10)
(7)
Lbs. (kg)
15d (6.8)d
15d
(6.8)d
The values in the above table are based on data in the National Bureau of Standard publications, “Building Materials and Structures Reports”.
Including other non-corrosive liquids and gases
ASTM B32, Alloy Grade Sn50
c ASTM B32, Alloy Grade Sb5
d This pressure is determined by the temperature of saturated steam @ 15 lbs. (6.8 kg) @ 250º F.
e The Safe Drinking Water Act Amendment of 1986 prohibits the use in potable water systems of any solder having a lead
content in excess of 0.2%.
a
b
BIV-50
®
PROPERTIES OF
VALVE MATERIALS
BRONZE AND BRASS
ALLOY
NAME
B62
COMPOSITION
BRONZE
Suitable to
450°F
NAVY M BRONZE
(Steam Bronze)
Suitable to
550°F
FORGING
BRASS
Suitable to
406°F
LEADED
BRASS
Suitable to
406°F
B61
B283
(37700)
B584
(C84400)
"K"
METAL
DEZINCIFICATION
RESISTANT
Suitable to
406°F
CHEMICAL
COMPOSITION
nominal
or
maximum
86.0
6.0
6.0
6.0
88.0
6.0
2.0
4.0
61.0
2.5
0.30
Rem.
82.0
3.5
8.0
10.0
1.0
0.40
0.08
0.02
62.0
3
3
Rem.
(PSI)
COPPER (Cu)
TIN (Sn)
LEAD (Pb)
ZINC (Zn)
COPPER (Cu)
TIN (Sn)
LEAD (Pb)
ZINC (Zn)
COPPER (Cu)
LEAD (Pb)
IRON (Fe)
ZINC (Zn)
COPPER (Cu)
TIN (Sn)
LEAD (Pb)
ZINC (Zn)
NICKEL
IRON (Fe)
SULPHER (S)
PHOSPHORUS(P)
COPPER (Cu)
LEAD (Pb)
IRON (Fe)
ZINC (Zn)
.75
.15
MATERIAL
NOMINAL
PHYSICAL PROPERTIES
TENSIL
YIELD
STRENGTH STRENGTH ELONGATION
(%)
(PSI)
(PSI)
30,000
14,000
20
34,000
16,000
22
50,000
18,000
25
29,000
13,000
18
110,000
20,000
11
PHOSPHORUS(P)
SULPHER (S)
31,000
––
––
.20
.45
.04
.05
COPPER (C)
MAGANESE (Mn)
PHOSPHORUS(P)
SILICON (Si)
100,000
––
18
.15
13
1.0
.04
1.0
.03
.08
20
1.5
2.5
11
.04
2.0
.04
.08
17
2.0
12
.045
1.0
.03
COPPER (C)
CHROME (Cr)
MAGANESE (Mn)
PHOSPHORUS(P)
SILICON (Si)
SULFUR (S)
COPPER (C)
CHROME (Cr)
MAGANESE (Mn)
MOLYBDENUM(Mo)
NICKEL (Ni)
PHOSPHORUS(P)
SILICON (Si)
SULFUR (S)
COPPER (C)
CHROME (Cr)
MAGANESE (Mn)
NICKEL (Ni)
PHOSPHORUS(P)
SILICON (Si)
SULFUR (S)
85,000
55,000
18
75,000
30,000
25
75,000
30,000
30
GRAY IRON
A126
CLASS B
GRAY IRON
CARBON STEEL
A307
Gr. B
STEEL BOLTING
STEEL NUTS
STAINLESS STEEL
A182-F6a
A-351
OTHER
PHYSICAL
A276-316
PROPERTIES
OF MATERIAL
AVAILABLE
UPON
REQUEST.
®
FORGED 410
CAST 316
(CF8M)
WROUGHT 316
BIV-51
PROPERTIES OF VALVE MATERIALS
ASTM
NO.
BRONZE VALVES SEATING & PACKING OPTIONS
BRONZE VALVES
SEATING AND PACKING OPTIONS
SEATING MATERIAL
Material:
Maximum Pressure:
Maximum Temperature:
Service:
PTFE
300 WSP / 600 CWP
-20 °F to 406 °F / Maximum Service Range
PTFE is suitable for oxygen, steam, and all services where the media being
handled is not corrosive to the metallic parts of the valve.
Material:
Maximum Pressure:
Service:
Bronze ASTM B62
150 WSP / 300 CWP
406 °F / Maximum Service Range
Bronze ASTM B62 provides good seating properties for clean moderate
service. However, it should not be used for close throttling or for handling
material containing abrasive or corrosive particles.
Material:
Maximum Pressure:
Service:
Bronze ASTM B61
300 WSP / 1000 CWP
Bronze ASTM B61 provides good seating properties for clean moderate
service. However, it should not be used for close throttling or for handling
material containing abrasive or corrosive particles.
Material:
Maximum Pressure:
Service:
Stainless Steel ASTM A276, Type 403
300 WSP / 600 CWP
Stainless Steel ASTM Type 403 is recommended for close throttling and
most all services conditions that do not exceed the valves service rating.
PACKING MATERIAL*
Aramid Fibers with Graphite
Standard packing material offered in Class 125 & 150 Bronze and Brass Valves.
Aramid Fibers with PTFE
Standard packing material offered in our Figure Number AK150L Code #42
Flexible Graphite with Aluminum
Standard packing material offered in Class 300 Bronze Gate and Globe valves.
*Packing Materials are designed to service the Pressure, Temperature and Media for the metallic body
material in which they reside.
KITZ Corporation reserves the right to change seating and packing material without notice.
BIV-52
®
IRON VALVES SEATING, PACKING &
GASKET MATERIAL OPTIONS
Material:
Maximum Pressure:
Service:
Bronze ASTM B62
125 WSP / 200 CWP
ASTM B 62 Bronze is suitable for Steam / Water, Oil and Gas. This
material is standard on all KITZ Iron Body Valves unless otherwise
specified.
Material:
Maximum Pressure:
Service:
Stainless Steel ASTM A276, Type 403
125 WSP / 200 CWP
Use this material when bronze trim is not permitted and for applications that
demand a more abrasive resistant seat material. Available on KITZ iron,
gate, globe and check valves.
PACKING MATERIAL*
1) The standard packing material for Gate valves is a combination structure of two parts. The end rings are
metal wire (SUS 304) reinforced glass fiber braided packing impregnated with tetrafluoroethylene resin.
The middle ring is Aramid Fibers reinforced expanded graphite packing impregnated with tetrafluoroethylene resin. Service range to 500 °F
2) The standard packing material for Globe valves is a combination structure of two parts. The end rings are
metal wire (SUS 304) reinforced glass fiber braided packing impregnated with tetrafluoroethylene resin.
The middle ring is Aramid Fibers reinforced expanded graphite packing impregnated with tetrafluoroethylene resin. Service range to 660 °F
GASKET MATERIAL*
The standard gasket material used in KITZ Gate, Globe and Check valves is a
non-asbestos jointing sheets made of inorganic fiber and filler, heat resisting organic fiber and oil resisting
rubber as a binder.
*Packing Materials are designed to service the Pressure, Temperature and Media for the metallic body
material in which they reside.
KITZ Corporation reserves the right to change seating and packing material without notice.
®
BIV-53
IRON VALVES SEATING, PACKING & GASKET MATERIAL OPTIONS
SEATING MATERIAL
Cv VALUES
Cv VALUES
BRONZE/BRASS/STAINLESS
CODE & FIG. NO.
1/4
3/8
1/2
3/4
1
1 1/4
1 1/2
2
2 1/2
3
4
4
6
-
8
8
8
8
8
8
8
8
8
-
13
20
20
20
13
21
20
20
13
13
20
20
20
20
13
-
37
37
38
38
36
38
39
31
36
36
38
38
38
38
36
36
36
68
61
64
64
57
62
64
64
57
57
64
64
64
64
57
57
57
108
108
109
109
101
109
110
109
101
101
109
109
109
109
101
-
141
176
177
177
140
177
180
177
140
140
177
177
177
177
140
-
272
280
287
287
271
282
292
287
271
271
287
287
287
287
271
-
498
276
513
513
273
498
498
-
742
395
773
773
392
742
773
-
926
1200
1220
-
1.2
1.2
1
1.2
1.2
1.2
1.2
1.2
1.2
1.9
1.9
1.6
1.9
1.9
1.9
1.9
1.2
1.9
1.9
3
3.5
2.6
3.6
3.6
4.3
4.3
3.6
4.5
3.5
3.6
7.4
5
7.5
7.5
7.3
7.3
7.5
7.3
7.4
7.4
11
8.6
12
12
11
11
12
11
11
11
20
15
21
21
20
20
21
20
20
20
26
22
27
27
31
31
27
29
26
26
45
40
46
46
48
48
46
44
45
44
68
62
70
70
76
68
66
87
77
89
89
112
87
133
-
-
3.6
3.0
3.0
3.0
-
6.0
6.0
4.0
4.0
4.0
3.0
4.0
4.0
8.0
3.0
13
13
5.0
5.0
8.0
6.0
5.0
5.0
15
6.0
24
24
9.0
9.0
15
10
9.0
9.0
24
10
41
40
15
15
26
16
126
15
40
16
59
59
26
26
37
25
39
26
66
25
108
108
39
39
68
42
70
39
108
42
188
182
70
110
110
70
188
-
285
265
110
162
110
278
-
390
-
4.0
-
5.4
5.4
10
10
17
17
25
25
35
35
67
67
106
106
167
167
-
GATE
05 AKFH
06 CFH
07 AKFS
08 CFS
24 AK125M
25 AK150L
27 AKH
28 CH
31 AKUEM/AKUELM
37 AK300LU
40 AK125E
41 C125E
42 AK150LU
43 C150LU
44 C125M
45 C150L
46 AK150E
47 AKHD
48 CHD
GLOBE
01 AKA
02 AKC
03 AKG
09 AK 150D
10 C150D
17 AK300J
17S AK300SJ
18 AK300D
33 AKUJM
38 AKCA
CHECK
04 AKR
14 CR
19 AK300YR
22 AKYR
23 CYR
26 CAF
29 AK150YR
30 C150YR
34 AKOUM
36 AKAF
STRAINERS
15 AKYR
16 CYR
IRON
CODE & FIG. NO.
2
21/2
3
4
5
6
8
10
12
14
-
261
261
261
476
476
476
756
756
756
1220
1220
1220
1980
1980
1980
2940
2940
2940
5440
5440
5440
8650
8650
8650
12,700
12,700
12,700
15,100
15,100
15,100
-
51
51
84
84
121
121
189
189
297
297
436
436
793
793
1270
1270
1800
1800
-
-
110
110
193
193
292
292
468
468
735
735
1060
1060
1880
1880
2940
2940
-
-
-
63
106
167
241
370
530
940
1400
2035
-
-
GATE
72 125FCL
73 125FCLS
75 125FCWI
GLOBE
76 125FCJ
77 125FCJS
CHECK
78 125FCO
79 125FCOS
STRAINERS
80 125FCYU
BIV-54
®
SATURATED STEAM TABLE
29
0.451
76.5
2
218.5
140
360.8
290
418.7
580
485.2
____________________________________________________________________________________________________________________________________
28
0.942
99.7
4
224.4
145
363.4
295
420.2
590
487.0
____________________________________________________________________________________________________________________________________
27
1.43
114.0
6
229.8
–
–
–
–
–
–
____________________________________________________________________________________________________________________________________
26
1.92
124.6
8
234.6
150
365.9
300
421.7
600
488.8
____________________________________________________________________________________________________________________________________
–
–
–
–
–
155
368.3
310
424.6
650
497.4
____________________________________________________________________________________________________________________________________
25
2.42
133.3
10
239.0
160
370.6
320
427.4
700
505.4
____________________________________________________________________________________________________________________________________
24
2.91
140.3
15
249.7
165
372.9
330
430.3
–
–
____________________________________________________________________________________________________________________________________
23
3.40
146.3
20
258.8
170
375.2
340
433.0
750
513.1
____________________________________________________________________________________________________________________________________
22
3.89
151.7
–
–
–
–
–
–
800
520.3
____________________________________________________________________________________________________________________________________
21
4.38
156.5
25
266.8
175
377.4
350
435.6
850
527.3
____________________________________________________________________________________________________________________________________
30
274.0
180
379.5
360
438.2
900
533.9
____________________________________________________________________________________________________________________________________
20
4.87
161.0
35
280.6
185
381.7
370
440.8
950
540.3
____________________________________________________________________________________________________________________________________
19
5.36
165.2
40
286.7
190
383.7
380
443.3
–
–
____________________________________________________________________________________________________________________________________
18
5.85
168.9
45
292.4
195
385.8
390
445.7
1000
546.4
____________________________________________________________________________________________________________________________________
17
6.35
172.5
–
–
–
–
–
–
–
–
____________________________________________________________________________________________________________________________________
16
6.84
175.8
50
297.7
200
387.8
400
448.1
–
–
____________________________________________________________________________________________________________________________________
–
–
–
55
302.6
205
389.7
410
450.5
–
–
____________________________________________________________________________________________________________________________________
15
7.33
178.9
60
307.3
210
391.7
420
452.8
–
–
____________________________________________________________________________________________________________________________________
14
7.82
181.8
65
311.8
215
393.6
430
455.1
–
–
____________________________________________________________________________________________________________________________________
13
8.31
184.6
70
316.0
220
395.4
440
457.3
–
–
____________________________________________________________________________________________________________________________________
12
8.80
187.2
–
–
–
–
–
–
–
–
____________________________________________________________________________________________________________________________________
11
9.29
189.7
75
320.0
225
397.3
450
459.5
–
–
____________________________________________________________________________________________________________________________________
–
–
–
80
323.9
230
399.1
460
461.7
–
–
____________________________________________________________________________________________________________________________________
10
9.78
192.1
85
327.6
235
400.8
470
463.8
–
–
____________________________________________________________________________________________________________________________________
9
10.27
194.4
90
331.1
240
402.6
480
465.9
–
–
____________________________________________________________________________________________________________________________________
8
10.77
196.7
95
334.6
245
404.3
490
468.0
–
–
____________________________________________________________________________________________________________________________________
7
11.26
198.8
–
–
–
–
–
–
–
–
____________________________________________________________________________________________________________________________________
6
11.75
200.9
100
337.9
250
406.0
500
470.0
–
–
____________________________________________________________________________________________________________________________________
–
–
–
105
341.1
255
407.7
510
472.0
–
–
____________________________________________________________________________________________________________________________________
5
12.24
202.9
110
344.1
260
409.3
520
474.0
–
–
____________________________________________________________________________________________________________________________________
4
12.73
204.8
115
347.1
265
410.9
530
475.9
–
–
____________________________________________________________________________________________________________________________________
3
13.22
206.7
120
350.0
270
412.5
540
477.8
–
–
____________________________________________________________________________________________________________________________________
2
13.71
208.5
–
–
–
–
–
–
–
–
____________________________________________________________________________________________________________________________________
1
14.20
210.3
125
352.8
275
414.1
550
479.7
–
–
____________________________________________________________________________________________________________________________________
0
14.696
®
212.0
130
355.6
280
415.7
560
481.6
–
–
BIV-55
SATURATED STEAM TABLE PRESSURE/TEMPERATURE
Vacuum
Pressure
Temperature
Pressure Temperature
Pressure Temperature Pressure Temperature
Pressure Temperature
Inches
Absolute
Gauge
Gauge
Gauge
Gauge
Mercury
(P.S.I.A.)
°F
(P.S.I.G.)
°F
( P.S.I.G.)
°F
( P.S.I.G.)
°F
( P.S.I.G.)
°F
____________________________________________________________________________________________________________________________________
29.74
0.089
32.0
0
212.0
135
358.3
285
417.2
570
483.4
____________________________________________________________________________________________________________________________________
BRONZE FLANGE DIMENSIONS
BRONZE
FLANGE DIMENSIONS
Flange diameters and drilling templates of 150-lb. bronze flanges are the same as the 125-lb. USA Cast-Iron
Standard (B16.1). Flange diameters and drilling templates of 250-lb. and 300-lb. bronze flanges are the same as
the 250-lb. USA Cast-Iron Flange Standard (B16.5). The faces of these flanges are machined with a serrated
spiral finish. When cast iron or steel flanges with raised faces are bolted to these flanges, the raised faces should
be removed. Full face gaskets should be used. Metallic gaskets should not be used.
CLASS 125 BRONZE FLANGES
(meets 125 lb. ASME Standard)
A
B
(Inch)
C
Nominal
Outside
Minimum
Diameter
Diameter
Size of
Diameter
Thickness
of Bolt
of Drilled
Diameter
Length
Number
Pipe
of Flange
of Flange
Circle
Bolt Holes
of Bolts
of Bolts
of Bolts
______________________________________________________________________________________________
/2
3 /2
/16
2 /8
/8
/2
1 /4
4
______________________________________________________________________________________________
1
3/4
1
3 3/8
3
3
3/16
2 3/4
5
1
1
5/8
1/2
1
1 /2
4
______________________________________________________________________________________________
1
4 /4
/4
3 /8
/8
/2
1 /2
4
______________________________________________________________________________________________
1
11/4
4 5/8
1
1/4
1
3 1/2
5
1
1
5/8
1/2
1
1 /2
4
______________________________________________________________________________________________
1 /2
5
/16
3 /8
/8
/2
1 /2
4
______________________________________________________________________________________________
1
3
7
3/8
4 3/4
5
1
1
3/4
5/8
3
2
6
1 /4
4
______________________________________________________________________________________________
2 /2
7
/8
5 /2
/4
/8
2
4
______________________________________________________________________________________________
1
3
7 1/2
1
7/16
3
5
3/4
5
3
6
/8
2
4
______________________________________________________________________________________________
4
9
/16
7 /2
/4
/8
2
8
______________________________________________________________________________________________
7
1
7/16
8 1/2
3
5
7/8
3
5
10
/4
2 /4
8
______________________________________________________________________________________________
1
6
11
/2
9 /2
/8
/4
2 /4
8
______________________________________________________________________________________________
1
13 1/2
5/8
1
11 3/4
7
3
1
7/8
3/4
1
8
2 /2
8
______________________________________________________________________________________________
10
16
/8
14 /4
1
/8
2 /2
12
______________________________________________________________________________________________
5
12
19
11/16
1
17
7
1
7/8
1
23/4
12
(meets ANSI B16.24 & Federal Spec. WW-F-406)
A
B
(Inch)
C
Nominal
Outside
Minimum
Diameter
Diameter
Size of
Diameter
Thickness
of Bolt
of Drilled
Diameter
Length
Number
Pipe
of Flange
of Flange
Circle
Bolt Holes
of Bolts
of Bolts
of Bolts
______________________________________________________________________________________________
/2
3 /2
/16
2 /8
/8
/2
1 /4
4
______________________________________________________________________________________________
1
3/4
1
3 7/8
5
11/32
3
2 3/4
5
1
1
5/8
1/2
1
1 /2
4
______________________________________________________________________________________________
1
4 /4
/8
3 /8
/8
/2
1 /2
4
______________________________________________________________________________________________
1
11/4
4 5/8
3
13/32
1
3 1/2
5
1
1
5/8
1/2
1
1 /2
4
______________________________________________________________________________________________
1 /2
5
/16
3 /8
/8
/2
1 /2
4
______________________________________________________________________________________________
1
7
1/2
7
4 3/4
5
1
1
3/4
5/8
3
2
6
1 /4
4
______________________________________________________________________________________________
2 /2
7
/16
5 /2
/4
/8
2
4
______________________________________________________________________________________________
1
9
7 1/2
1
5/8
3
5
3/4
5
3
6
/8
2
4
______________________________________________________________________________________________
4
9
/16
7 /2
/4
/8
2 /4
8
______________________________________________________________________________________________
11
3/4
1
8 1/2
3
5
1
7/8
3/4
1
5
10
2 /2
8
______________________________________________________________________________________________
6
11
/16
9 /2
/8
/4
2 /2
8
______________________________________________________________________________________________
13
13 1/2
15/16
1
11 3/4
7
3
1
7/8
3/4
3
8
2 /4
8
______________________________________________________________________________________________
10
16
1
14 /4
1
/8
3 /4
12
______________________________________________________________________________________________
1
12
BIV-56
19
11/16
17
7
1
7/8
1
31/4
12
®
BRONZE
FLANGE DIMENSIONS
(meets ASME/ANSI B16.24)
A
B
BRONZE FLANGE DIMENSIONS
(Inch)
C
Nominal
Outside
Minimum
Diameter
Diameter
Size of
Diameter
Thickness
of Bolt
of Drilled
Diameter
Length
Number
Pipe
of Flange
of Flange
Circle
Bolt Holes
of Bolts
of Bolts
of Bolts
______________________________________________________________________________________________
/2
3 /4
/32
2 /8
/8
/2
1 /2
4
______________________________________________________________________________________________
1
1
13
1
5
1
1
/4
4 /8
/16
3 /4
/4
/8
1 /4
4
______________________________________________________________________________________________
3
3
4 7/8
7
1
1/2
3 1/2
3
5
3
3/4
5/8
3
1
1 /4
4
______________________________________________________________________________________________
1 /4
5 /4
/32
3 /8
/4
/8
2
4
______________________________________________________________________________________________
1
1
11/2
6 1/8
17
9/16
7
4 1/2
3
5
7/8
3
/4
2
4
______________________________________________________________________________________________
2
6 /2
/8
5
/8
/4
2
8
______________________________________________________________________________________________
1
21/2
7 1/2
5
11/16
5 7/8
7
3
3/4
5
/8
2 /4
8
______________________________________________________________________________________________
1
3
8 /4
/4
6 /8
/8
/4
2 /2
8
______________________________________________________________________________________________
1
3
7/8
3
7 7/8
7
3
1
7/8
3/4
3
4
10
2 /4
8
______________________________________________________________________________________________
5
11
/16
9 /4
/8
/4
2 /4
8
______________________________________________________________________________________________
13
12 1/2
1
10 3/8
7
3
7/8
3/4
3
6
1
3
12
______________________________________________________________________________________________
8
15
1 /8
13
1
/8
3 /4
12
______________________________________________________________________________________________
1
7
13/16
15 1/4
11/8
20 1/2
11/4
17 3/4
11/4
1
10
1
3 /4
16
______________________________________________________________________________________________
12
17 1/2
1
11/8
31/4
16
(meets ASME/ANSI B16.24)
A
B
(Inch)
C
Nominal
Outside
Minimum
Diameter
Diameter
Size of
Diameter
Thickness
of Bolt
of Drilled
Diameter
Length
Number
Pipe
of Flange
of Flange
Circle
Bolt Holes
of Bolts
of Bolts
of Bolts
______________________________________________________________________________________________
/2
3 /4
/2
2 /8
/8
/2
1 /4
4
______________________________________________________________________________________________
1
3
1
5
5
1
1
/4
4 /8
/32
3 /4
/4
/8
2
4
______________________________________________________________________________________________
3
5
4 7/8
17
19/32
1
3 1/2
3
5
3/4
5
1
/8
2
4
______________________________________________________________________________________________
1 /4
5 /4
/8
3 /8
/4
/8
2
4
______________________________________________________________________________________________
1
1
11/2
6 1/8
5
11/16
7
4 1/2
3
5
3/4
5
/8
2 /4
4
______________________________________________________________________________________________
1
2
6 /2
/4
5
/8
/4
2 /4
8
______________________________________________________________________________________________
1
21/2
7 1/2
3
13/16
5 7/8
7
3
1
7/8
3/4
1
2 /2
8
______________________________________________________________________________________________
3
8 /4
/32
6 /8
/8
/4
2 /4
8
______________________________________________________________________________________________
1
29
11/16
5
7 7/8
7
3
7/8
3/4
3
4
10
3
8
______________________________________________________________________________________________
5
11
1 /8
9 /4
/8
/4
1 /4
8
______________________________________________________________________________________________
1
1
7
3
1
12 1/2
13/16
10 5/8
7/8
3/4
1
15
13/8
13
1
7/8
33/4
6
3 /4
12
______________________________________________________________________________________________
8
®
12
BIV-57
CAST IRON
FLANGE DIMENSIONS
CLASS 125 CAST IRON FLANGES
CAST IRON FLANGE DIMENSIONS
(ASME/ANSI STANDARD B16.1)
Mates with 150-lb. steel flanges ASME/ANSI Standard B16.5
A
B
(Inch)
C
Nominal
Outside
Minimum
Diameter
Diameter
Size of
Diameter
Thickness
of Bolt
of Drilled
Diameter
*Length
Number
Pipe
of Flange
of Flange
Circle
Bolt Holes
of Bolts
of Bolts
of Bolts
______________________________________________________________________________________________
2
6
/8
4 /4
/4
/8
2 /4
4
______________________________________________________________________________________________
5
3
3
5
1
2 /2
7
/16
5 /2
/4
/8
2 /2
4
______________________________________________________________________________________________
1
11
7 1/2
1
3/4
3
5
1
3/4
5/8
1
3
6
2 /2
4
______________________________________________________________________________________________
13
3 /2
8 /2
/16
7
/4
/8
2 /4
8
______________________________________________________________________________________________
1
1
15/16
7 1/2
3
5
3/4
5/8
3
4
9
3
8
______________________________________________________________________________________________
5
10
/16
8 /2
/8
/4
3
8
______________________________________________________________________________________________
15
1
9 1/2
7
3
7/8
3
6
11
1
/4
3 /4
8
______________________________________________________________________________________________
1
8
13 /2
1 /8
11 /4
/8
/4
3 /2
8
______________________________________________________________________________________________
1
1
13/16
3
7
14 1/4
3
1
7/8
3
10
16
1
3 /4
12
______________________________________________________________________________________________
12
19
1 /4
17
1
/8
3 /4
12
______________________________________________________________________________________________
1
13/8
7
11/8
3
14
21
1
4 /4
12
______________________________________________________________________________________________
7
183/4
1
16
23 /2
1 /16
21 /4
1 /8
1
4 /2
16
______________________________________________________________________________________________
1
19/16
1
223/4
1
1
18
25
4 /4
16
______________________________________________________________________________________________
11
11/4
11/8
3
20
27 /2
1 /16
25
1 /4
1 /8
5
20
______________________________________________________________________________________________
1
24
32
17/8
291/2
1
1
13/8
11/4
51/2
20
*When bolting to steel flanges, longer bolts may be required.
CLASS 250 CAST IRON FLANGES
(ANSI STANDARD B16.1)
Mates with 300-lb. steel flanges ASME/ANSI Standard B16.5
A
B
(Inch)
C
Nominal
Outside
Minimum
Diameter
Diameter
Size of
Diameter
Thickness
of Bolt
of Drilled
Diameter
*Length
Number
Pipe
of Flange
of Flange
Circle
Bolt Holes
of Bolts
of Bolts
of Bolts
______________________________________________________________________________________________
1
2
6 /2
/8
5
/4
/8
2 /4
8
______________________________________________________________________________________________
21/2
7
71/2
5 7/8
3
5
3
7/8
3/4
1
1
3 /4
8
______________________________________________________________________________________________
3
8 /4
1 /8
6 /8
/8
/4
3 /2
8
______________________________________________________________________________________________
1
31/2
1
5
13/16
71/4
7
3
1
7/8
3/4
1
9
3 /2
8
______________________________________________________________________________________________
4
10
1 /4
7 /8
/8
/4
3 /4
8
______________________________________________________________________________________________
1
7
13/8
91/4
7
3
7/8
3/4
3
5
11
4
8
______________________________________________________________________________________________
7
6
12 /2
1 /16
10 /8
/8
/4
4
12
______________________________________________________________________________________________
1
5
7
15/8
3
8
15
13
1
/8
4 /2
12
______________________________________________________________________________________________
7
7
1
10
17 /2
1 /8
15 /4
1 /8
1
5 /4
16
______________________________________________________________________________________________
1
201/2
1
173/4
1
11/4
1
11/8
12
2
5 /2
16
______________________________________________________________________________________________
1
14
23
2 /8
20 /4
1 /4
1 /8
6
20
______________________________________________________________________________________________
1
251/2
21/4
1
1
1
13/8
1
16
1 /4
6 /4
20
______________________________________________________________________________________________
3
221/2
1
18
28
2 /8
24 /4
1 /8
1 /4
6 /2
24
______________________________________________________________________________________________
301/2
21/2
36
23/4
3
3
1
1
13/8
11/4
3
15/8
11/2
71/2
20
27
6 /4
24
______________________________________________________________________________________________
24
32
24
*When bolting to steel flanges, longer bolts may be required.
BIV-58
®
ASME/ANSI STANDARD IRON PIPE
TAPER THREADS
A = G–(0.05 + 1.1) P
B = A + .0625 F
E = P(0.8G + 6.8)
Depth of Thread = 0.8 P
Total Taper 3/4 in. per foot
DUE TO LEAD
OF DIE
(Inch)
A
B
E
F
G
H
P
Normal
Engagement
by Hand
Between
Male and
Female
Thread
Outside
Dia. of
Pipe
Actual
Inside
Dia. of
Pipe
Number
of
Threads
Pitch
of
Thread
Depth of
Thread
Nominal
Size
of Pipe
Pitch Dia.
at End of
Pipe
Pitch Dia.
at Gauging
Notch
Length
of
Effective
Thread
1/8
3/4
.36351
.47739
.61201
.75843
.96768
.37476
.48989
.62701
.77843
.98886
.2638
.4018
.4078
.5337
.5457
.180
.200
.240
.320
.339
.405
.540
.675
.840
1.050
.269
.364
.493
.622
.824
27
18
18
14
14
.0370
.0556
.0556
.0714
.0714
.02963
.04444
.04444
.05714
.05714
1
11/4
11/2
2
21/2
1.21363
1.55713
1.79609
2.26902
2.71953
1.23863
1.58338
1.82234
2.29627
2.76216
.6828
.7068
.7235
.7565
1.1375
.400
.420
.420
.436
.682
1.315
1.660
1.900
2.375
2.875
1.049
1.380
1.610
2.067
2.469
111/2
111/2
111/2
111/2
8
.0870
.0870
.0870
.0870
.1250
.06956
.06956
.06956
.06956
.10000
3
31/2
4
5
3.34063
3.83750
4.33438
5.39073
3.38850
3.88881
4.38713
5.44929
1.2000
1.2500
1.3000
1.4063
.766
.821
.844
.937
3.500
4.000
4.500
5.563
3.068
3.548
4.026
5.047
8
8
8
8
.1250
.1250
.1250
.1250
.10000
.10000
.10000
.10000
6
8
10
6.44609
8.43359
10.54531
6.50597
8.50003
10.62094
1.5125
1.7125
1.9250
.958
1.063
1.210
6.625
8.625
10.750
6.065
7.981
10.020
8
8
8
.1250
.1250
.1250
.10000
.10000
.10000
12
12.53281
12.61781
2.1250
1.360
12.750
12.000
8
.1250
.10000
1/4
3/8
1/2
Data abstracted from ASME/ANSI Standard B1.20.1–1983 – Gages and Gaging for Unified Inch Screw Threads.
®
BIV-59
ASME/ANSI STANDARD IRON PIPE TAPER THREADS
IMPERFECT THREAD
STANDARD COPPER WATER TUBE & SOLDER-JOINT END VALVES & FITTINGS
ASME/ANSI STANDARD COPPER WATER TUBE
& SOLDER-JOINT ENDS VALVES & FITTINGS
As steam installations, the successful application of
copper tube depends upon weight of tube and solder
used when making joints. The solder must have a
melting point high enough to remain unaffected by the
temperature of the steam.
SERVICE RECOMMENDATIONS
Seamless copper water tube is used for such services
as steam, water or air and oil, gas or similar fluids.
Type K Tube is especially recommended for underground use and where service conditions are severe. It
is also recommended for general plumbing and heating
systems and is used for gas, oil and steam.
HARD COPPER TUBE: Hard copper tube is intended
primarily for use in straight lengths. Without proper
bending equipment, its use is not recommended for
field bending.
Type L Tube is for interior use in general plumbing
and heating work.
SOFT COPPER TUBE: This tube can be bent without special bending equipment and is recommended
for use when bends must be made in the field, as in
concealed replacement work. Soft copper tubing may
become flattened or distorted when being handled or
while in transit. The ends of this tube should therefore
be sized to assure a tight soldered joint.
Type M Tube is for use
with solder-joint fittings
only, for waste, vent and
interior drainage lines
and other non-pressure
applications.
Type K (hard and soft) and Type L (hard and soft) in
sizes 3/8" to 12" and Type M (hard) in sizes 21/2" to
12" conform to ANSI Standard for Copper Water
Tube, H23.1. Also conforms to Federal Specification
WW-T-799.
TUBE DIMENSIONS AND WEIGHTS
DIMENSIONS OF SOLDER-JOINT ENDS
Standard
Water
Tube
Size Inches
A
Inside Diameter
Min. Inches
Max. Inches
B
Depth
Min. Inches
1/4
5/16
.377
.381
_________________________________________________________________
3/8
3/8
.502
.506
_________________________________________________________________
1/2
1/2
.627
.631
_________________________________________________________________
3/4
3/4
.877
.881
_________________________________________________________________
29/32
1
1.128
1.132
_________________________________________________________________
31/32
11/4
1.378
1.382
_________________________________________________________________
11/2
1.628
1.633
13/32
_________________________________________________________________
11/32
2
2.128
2.133
1
_________________________________________________________________
21/2
2.628
2.633
115/32
_________________________________________________________________
3
3.128
3.133
121/32
_________________________________________________________________
31/2
3.628
3.633
129/32
_________________________________________________________________
4
4.128
4.133
25/32
_________________________________________________________________
5
5.128
5.133
221/32
_________________________________________________________________
6
6.128
6.133
33/32
_________________________________________________________________
8
8.128
8.133
331/32
Nominal
Size
of
Tube
In.
1
Actual
Outside
Diam.
of Tube
In.
Type K Tube
Wall
Thickness
In.
Wgt.
Per
Foot
Lbs.
Type L Tube
Wall
Thickness
In.
Wgt.
Per
Foot
Lbs.
Type M Tube
Wall
Thickness
In.
Wgt.
Per
Foot
Lbs.
3
/4
/8
.030
.126
––
––
––
––
_______________________________________________________________________
1/2
3/8
.049
.269
.035
.198
––
––
_______________________________________________________________________
1/2
5/8
.049
.344
.040
.285
––
––
_______________________________________________________________________
3/4
7/8
.065
.641
.045
.455
––
––
_______________________________________________________________________
.065
.839
.050
.655
––
––
1
11/8
_______________________________________________________________________
13/8
.065
1.04
.055
.884
.042
.68
11/4
_______________________________________________________________________
15/8
.072
1.36
.060
1.14
.049
.94
11/2
_______________________________________________________________________
.083
2.06
.070
1.75
.058
1.46
2
21/8
_______________________________________________________________________
25/8
.095
2.93
.080
2.48
.065
2.03
21/2
_______________________________________________________________________
.109
4.00
.090
3.33
.072
2.68
3
31/8
_______________________________________________________________________
35/8
.120
5.12
.100
4.29
.083
3.58
31/2
_______________________________________________________________________
.130
6.51
.110
5.38
.095
4.66
4
41/8
_______________________________________________________________________
.160
9.67
.125
7.61
.109
6.66
5
51/8
_______________________________________________________________________
.192
13.90
.140
10.20
.122
8.92
6
61/8
_______________________________________________________________________
.271
25.90
.200
19.30
.170 16.50
8
81/8
_______________________________________________________________________
.338
40.30
.250
30.10
.212 25.60
10
101/8
_______________________________________________________________________
.405
57.80
.280
40.40
.254 36.70
12
121/8
Data extracted from ASME/ANSI Standard 16.18–1984 (R1994) – Cast Copper Alloy Solder Joint Pressure Fittings.
BIV-60
®
VALVE INSTALLATION TIPS FOR
A SOUND SOLDER JOINT
1. Solders
Recommended:
Soft solders having a maximum melting point of 420°F.
Others: 95-5 tin-antimony (460°F)
96.5-3.5 tin-silver (430°F)
2. Soldering Procedure
(1) Cut tube end square; ream, burr and size.
(2) Polish tube and cup to a bright metal finish, using sand cloth, wire brush and clean with cloth.
(3) Apply flux sparingly and evenly to polished surface of tube. No flux need be applied to solder cup.
(4) Fully open valve before applying heat. Insert tube into valve socket until it contacts internal shoulder of
valve socket. Rotate the tube a few times to evenly distribute flux.
(5) Soldering procedure:
(a) Cover the bonnet or valve body with a wet cloth to prevent gland packing and seat damage.
(b) Preheat the tube evenly, using an open-flame torch.
(c) Heat the joint area to an adequate temperature and remove heat and feed solder around the joint.
(d) Check to make sure melted solder is flowing into the jointed surfaces.
(e) Visually check joint for continuous fillet.
(f) Cool the jointed area with a wet cloth as soon as the solder becomes solid.
(g) After cooling, remove solder and flux to prevent surface corrosion.
(h) Flush the tube and valve interiors with water to remove internal residue, as soon as piping
installation is complete.
CAUTION
(1)
(2)
(3)
(4)
(5)
(6)
®
Do apply wet cloth to body of valve or bonnet, to prevent damage to seat and packing
during soldering.
Do not apply heat to the valve body, to prevent damage to seats and packing.
Do, minimize heating time for solder work, to prevent damage to seats and packing
Do not forget to retighten packing nut after valve cools down for leak-free performance.
Do remember that Service Pressure and Temperature of valve are limited by the properties
of the solder.
Do not exceed a service velocity greater than 6 feet per second, to prevent erosion of
copper tube.
BIV-61
VALVE INSTALLATION TIPS FOR A SOUND SOLDER JOINT
Kitz solder joint copper alloy ball, gate, globe and check valves are designed to be soft soldered into lines
without disassembly, using a low temperature solder 420°F. Other solders, 95/5 tin antimony (460°F) or
96/4 tin silver (430°F) can be used, however, extreme caution must be used to prevent seat and packing
damage. Carefully following the succeeding procedure will assure a durable solder connection with copper
tubing for servicing distribution of water, oil and gas.
CONVERSION
TABLES
CONVERSION TABLES
LENGTH
1 in.
1 mm
1 ft.
1 meter
1 micron
PRESSURE
=
=
=
=
=
25.4 mm
.03937 in.
30.48 cm.
3.28083 ft.
.001 mm.
=
=
=
=
6.4516 sq. cm.
929.03 sq. cm.
0.155 sq. in.
0.0010764 sq. ft.
=
=
=
=
=
=
=
=
=
=
=
=
=
=
16.387 cu. cm.
1728 cu. in.
7.4805 U.S. gal.
6.229 British gal.
28.317 liters
0.1337 cu. lt.
231 cu. in.
3.785 liters
1.20094 U.S. gal.
277.3 cu. in.
4.546 liters
61.023 cu. in.
0.03531 cu. ft.
0.2642 U.S. gal.
=
=
=
=
=
=
=
=
28.35 g.
453.59 g.
0.03527 oz. av.
2.205 lb. av.
62.425 lb.
8.33 lb.
0.0361 lb.
10.04 lb.
=
0.080728 lb.
=
=
30.48 cm. per sec.
.032808 ft. per sec.
AREA
1 sq. in.
1 sq. ft.
1 sq. cm.
1 sq. cm.
VOLUME
1 cu. in.
1 cu. ft.
1 cu. lt.
1 cu. lt.
1 cu. lt.
1 U.S. gal.
1 U.S. gal.
1 U.S. gal.
1 British gal.
1 British gal.
1 British gal.
1 liter
1 liter
1 liter
WEIGHT
1 ounce av.
1 lb. av.
1 gram
1 kg.
1 cu. ft. of water
1 U.S. gal. of water
1 cu. in. of water
1 British gal. of water
1 cu. ft. of air at
32°F & 1 atm
VELOCITY
1 ft. per sec.
1 cm. per sec.
FLOW
1 cu. ft. per sec.
1 cu. ft. per sec.
1 U.S. gal. per min.
1 U.S. gal. per min.
1 cu. cm. per sec.
=
=
=
=
=
448.83 gal. per min.
1699.3 liters per min.
0.002228 cu. ft. per sec.
0.06308 liters per sec.
0.0021186 cu. ft. per min.
DENSITY
1 lb. per cu. ft.
1 lb. per cu. ft.
1 kg. per cu. meter
1 g. per cu. cm.
=
=
=
=
16.018 kg. per cu. meter
.0005787 lb. per cu. in.
0.06243 lb. per cu. ft.
0.03613 lb. per cu. in.
=
=
.000672 lb. per ft. sec.
.00001076 sq. ft. per sec.
1 in. of water
1 in. of water
1 ft. of water
1 ft. of water
1 in. of mercury
1 in. of mercury
1 in. of mercury
1 atmosphere
1 atmosphere
1 atmosphere
1 atmosphere
1 lb. per sq. in.
1 lb. per sq. in.
1 lb. per sq. in.
1 kg. per sq. cm.
1 dyne per sq. cm.
1 micron
1kPa
PSI to Bar
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
=
0.03613 lb. per sq. in.
0.07355 in. of Hg.
0.4335 lb. per sq. in.
0.88265 in. of Hg.
0.49116 lb. per sq. in.
13.596 in. of water
1.13299 ft. of water
14.696 lb. per sq. in. (PSIA)
760 mm. of Hg.
29.921 in. of Hg.
33.899 ft. of water
27.70 in. of water
2.036 in. of Hg.
.0703066 kg. per sq. cm.
.0000145 lb. per sq. in.
.00001943 lb. per sq. in.
PSI x 0.0689
=
=
=
=
=
=
777.97 ft. lbs.
9.4805 x 1011 B.T.U.
7.3756 x 108 ft. lbs.
2.655 x 106 ft. lbs.
1.3410 h.p. hr.
3.968 B.T.U.
=
=
=
=
=
=
33,000 ft. lb. per min.
550 ft. lb. per sec.
2,546.5 B.T.U. per hr.
745.7 watts
0.00134 horsepower
44.26 ft. lbs. per min.
ENERGY
1 B.T.U.
1 erg
1 erg
1 kilowatt hour
1 kilowatt hour
1 kg. calorie
POWER
1 horsepower
1 horsepower
1 horsepower
1 horsepower
1 watt
1 watt
TEMPERATURE
Temperature Fahrenheit (F)
Temperature Centigrade (C)
Temperature Reaumur
(R)
Absolute Temperature
Centigrade or Kelvin (K)
Absolute Temperature
Fahrenheit or Rankine (R)
Fahrenheit to Centigrade
= 9/5 Centigrade (C) + 32 = 9/4 R + 32
= 5/9 Fahrenheit (F) – 32 = 5/4 R
= 4/9 Fahrenheit (F) – 32 = 4/5 C
= Degrees C + 273.16
= Degrees F + 459.69
= C = (F – 32) / 1.8
HEAT TRANSFER
1 B.T.U. per sq. ft.
1 g. calorie per sq. cm.
1 B.T.U. per hr.
per sq. ft. per °F
1 Kg. cal. per hr.
per sq. m. per °C
1 Boiler Horsepower
= .2712 g. cal. per sq. cm.
= 3.687 B.T.U. per sq. ft.
= 4.88 kg. cal. per hr.
per sq. m. per °C
= .205 B.T.U. per hr. per sq. ft.
per °F
= 33479 B.T.U. per hr.
VISCOSITY
1 Centipoise
1 Centistoke
BIV-62
®
CONVERSION CHART
FRACTION – DECIMAL – MILLIMETER
9/64
5/32
…
11/64
3/16
1/4
…
…
13/64
7/32
…
15/64
… … …
17/64
9/32
3/8
…
19/64
5/16
… …
21/64
11/32
…
23/64
… … …
25/64
13/32
…
27/64
7/16
1/2
…
29/64
15/32
…
31/64
… … …
NOTE:
®
…
…
…
…
…
…
…
…
…
.140625
.15625
.171875
.1875
.203125
.21875
.234375
.25
3.57188
3.96876
4.36563
4.76251
5.15939
5.55626
5.95314
6.35001
…
…
…
…
…
…
…
…
.265625
.28125
.296875
.3125
.328125
.34375
.359375
.375
6.74689
7.14376
7.54064
7.93752
8.33439
8.73127
9.12814
9.52502
…
…
…
…
…
…
…
…
.390625
.40625
.421875
.4375
.453125
.46875
.484375
.5
9.92189
10.31877
10.71565
11.11252
11.50940
11.90627
12.30315
12.70002
Fraction
Decimal
Millimeter
__________________________________________________
33/64
…
.515625
13.09690
17/32
…
…
.53125
13.49378
35/64
…
.546875
13.89065
9/16
… …
…
.5625
14.28753
37/64
…
.578125
14.68440
19/32
…
…
.59375
15.08128
39/64
…
.609375
15.47816
5/8
… … … …
.625
15.87503
41/64
21/32
…
43/64
11/16
…
…
45/64
23/32
…
47/64
3/4
…
…
…
49/64
25/32
7/8
…
51/64
13/16
… …
53/64
27/32
…
55/64
… … …
57/64
29/32
…
59/64
15/16
…
…
61/64
31/32
…
63/64
1
…
…
…
…
…
…
…
…
…
…
…
.640625
.65625
.671875
.6875
.703125
.71875
.734375
.75
16.27191
16.66878
17.06566
17.46253
17.85941
18.25629
18.65316
19.05004
…
…
…
…
…
…
…
…
.765625
.78125
.796875
.8125
.828125
.84375
.859375
.875
19.44691
19.84379
20.24066
20.63754
21.03442
21.43129
21.82817
22.22504
…
…
…
…
…
…
…
…
.890625
.90625
.921875
.9375
.953125
.96875
.984375
1.0
22.62192
23.01880
23.41567
23.81255
24.20942
24.60630
25.00317
25.40005
To convert from inches to millimeters, multiply by 25.4
To convert from millimeters to inches, multiply by .03937.
Decimal conversion, 2.54 millimeters equals .10 of an inch.
BIV-63
CONVERSION TABLES
Fraction
Decimal
Millimeter
__________________________________________________
1/64
…
.015625
0.39688
1/32
…
…
.03125
0.79375
3/64
…
.046875
1.19063
1/16
… …
…
.0625
1.58750
5/64
…
.078125
1.98438
3/32
…
…
.09375
2.38125
7/64
…
.109375
2.77813
1/8
… … … …
.125
3.17501
TEMPERATURE CONVERSIONS
TEMPERATURE CONVERSION
°C = 5/9 (°F-32)
-459.4 to 12
°C
°F =(9/5 x °C) + 32
13 to 72
°F
°C
°C
°F
°C
°F
-273
-268
-262
-257
-251
-459.4
-450
-440
-430
-420
- 10.6
- 10.0
- 9.4
- 8.9
- 8.3
13
14
15
16
17
-246
-240
-234
-229
-223
-410
-400
-390
-380
-370
-
7.8
7.2
6.7
6.1
5.6
-218
-212
-207
-201
-196
-360
-350
-340
-330
-320
-
-190
-184
-179
-173
-169
-310
-300
-290
-280
-273
-
-168
-162
-157
-151
-146
-270
-260
-250
-240
-230
-140
-134
-129
-123
-118
73 to 260
°F
°C
265 to 620
°F
°C
°F
°C
°C
°F
°C
°F
55.4
57.2
59.0
60.8
62.6
22.8
23.3
23.9
24.4
25.0
73
74
75
76
77
163.4
165.2
167.0
168.8
170.6
129
132
135
138
141
265
270
275
280
285
509
518
527
536
545
332
338
343
349
354
630
640
650
660
670
1,166
1,184
1,202
1,220
1,238
18
19
20
21
22
64.4
66.2
68.0
69.8
71.6
25.6
26.1
26.7
27.2
27.8
78
79
80
81
82
172.4
174.2
176.0
177.8
179.6
143
146
149
152
154
290
295
300
305
310
554
563
572
581
590
360
366
371
377
382
680
690
700
710
720
1,256
1,274
1,292
1,310
1,328
5.0
4.4
3.9
3.3
2.8
23
24
25
26
27
73.4
75.2
77.0
78.8
80.6
28.3
28.9
29.4
30.0
30.6
83
84
85
86
87
181.4
183.2
185.0
186.8
188.6
157
160
163
166
168
315
320
325
330
335
599
608
617
626
635
388
393
399
404
410
730
740
750
760
770
1,346
1,364
1,382
1,400
1,418
-459.4
2.2
1.7
1.1
0.6
0.0
28
29
30
31
32
82.4
84.2
86.0
87.8
89.6
31.1
31.7
32.2
32.8
33.3
88
89
90
91
92
190.4
192.2
194.0
195.8
197.6
171
174
177
179
182
340
345
350
355
360
644
653
662
671
680
416
421
427
432
438
780
790
800
810
820
1,436
1,454
1,472
1,490
1,508
-454
-436
-418
-400
-382
0.6
1.1
1.7
2.2
2.8
33
34
35
36
37
91.4
93.2
95.0
96.8
98.6
33.9
34.4
35.0
35.6
36.1
93
94
95
96
97
199.4
201.2
203.0
204.8
206.6
185
188
191
193
196
365
370
375
380
385
689
698
707
716
725
443
449
454
460
466
830
840
850
860
870
1,526
1,544
1,562
1,580
1,598
-220
-210
-200
-190
-180
-364
-346
-328
-310
-292
3.3
3.9
4.4
5.0
5.6
38
39
40
41
42
100.4
102.2
104.0
105.8
107.6
36.7
37.2
37.8
41
43
98
99
100
105
110
208.4
210.2
212.0
221
230
199
202
214
207
210
390
395
400
405
410
734
743
752
761
770
471
477
482
488
493
880
890
900
910
920
1,616
1,634
1,652
1,670
1,688
-112
-107
-101
- 96
- 90
-170
-160
-150
-140
-130
-274
-256
-238
-220
-202
6.1
6.7
7.2
7.8
8.3
43
44
45
46
47
109.4
111.2
113.0
114.8
116.6
46
49
52
54
57
115
120
125
130
135
239
248
257
266
275
213
216
218
221
224
415
420
425
430
435
779
788
797
806
815
499
504
510
516
521
930
940
950
960
970
1,706
1,724
1,742
1,760
1,778
- 84
- 79
- 73
- 68
- 62
-120
-110
-100
- 90
- 80
-184
-166
-148
-130
-112
8.9
9.4
10.0
10.6
11.1
48
49
50
51
52
118.4
120.2
122.0
123.8
125.6
60
63
66
68
71
140
145
150
155
160
284
293
302
311
320
227
229
232
235
238
440
445
450
455
460
824
833
842
851
860
527
532
538
549
560
980
990
1,000
1,020
1,040
1,796
1,814
1,832
1,868
1,904
- 57
- 51
- 46
- 40
- 34
- 70
- 60
- 50
- 40
- 30
- 94
- 76
- 58
- 40
- 22
11.7
12.2
12.8
13.3
13.9
53
54
55
56
57
127.4
129.2
131.0
132.8
134.6
74
77
79
82
85
165
170
175
180
185
329
338
347
356
365
241
243
246
249
252
465
470
475
480
485
869
878
887
896
905
571
582
593
604
616
1,060
1,080
1,100
1,120
1,140
1,940
1,976
2,012
2,048
2,084
- 29
- 23
- 17.8
- 17.2
- 16.7
- 20
- 10
0
1
2
- 4
14
32
33.8
35.6
14.4
15.0
15.6
16.1
16.7
58
59
60
61
62
136.4
138.2
140.0
141.8
143.6
88
91
93
96
99
190
195
200
205
210
374
383
392
401
410
254
257
260
266
271
490
495
500
510
520
914
923
932
950
968
627
638
649
704
760
1,160
1,180
1,200
1,300
1,400
2,120
2,156
2,192
2,372
2,552
- 16.1
- 15.6
- 15.0
- 14.4
- 13.9
3
4
5
6
7
37.4
39.2
41.0
42.8
44.6
17.2
17.8
18.3
18.9
19.4
63
64
65
66
67
145.4
147.2
149.0
150.8
152.6
102
104
107
110
113
215
220
225
230
235
419
428
437
446
455
277
282
288
293
299
530
540
550
560
570
986
1,004
1,022
1,040
1,058
816
871
927
982
1,038
1,500
1,600
1,700
1,800
1,900
2,732
2,912
3,092
3,272
3,452
- 13.3
- 12.8
- 12.2
- 11.7
- 11.1
8
9
10
11
12
46.4
48.2
50.0
51.8
53.6
20.0
20.6
21.1
21.7
22.2
68
69
70
71
72
154.4
156.2
158.0
159.8
161.6
116
118
121
124
127
240
245
250
255
260
464
473
482
491
500
304
310
316
321
327
580
590
600
610
620
1,076
1,094
1,112
1,130
1,148
1,093
1,149
1,204
1,260
1,316
2,000
2,100
2,200
2,300
2,400
3,632
3,812
3,992
4,172
4,352
BIV-64
°C
630 to 2,400
°F
°F
®
CONVERSION CHART
PRESSURE
1 to 60
1 lbs./In.2 = 0.0703 kgs./cm2
61 to 200
lbs./in.2
kgs./cm.2
kgs./cm2
lbs./in.2
710 to 1,600
lbs./in.2
kgs./cm.2
kgs./cm2
lbs./in.2
kgs./cm2
lbs./in.2
kgs./cm.2
0.07
0.14
0.21
0.28
0.35
1
2
3
4
5
14.22
28.45
42.67
56.89
71.12
4.29
4.36
4.43
4.50
4.57
61
62
63
64
65
868
882
896
910
925
14.41
14.76
15.12
15.47
15.82
205
210
215
220
225
2,916
2,987
3,058
3,129
3,200
49.92
50.62
51.32
52.03
52.73
710
720
730
740
750
0.42
0.49
0.56
0.63
0.70
6
7
8
9
10
85.34
99.56
113.78
128.01
142.23
4.64
4.71
4.78
4.85
4.92
66
67
68
69
70
939
953
967
981
996
16.17
16.52
16.87
17.23
17.58
230
235
240
245
250
3,271
3,342
3,414
3,485
3,556
53.43
54.14
54.84
55.54
56.25
0.77
0.84
0.91
0.98
1.05
11
12
13
14
15
156.45
170.68
184.90
199.12
213.35
4.99
5.06
5.13
5.20
5.27
71
72
73
74
75
1,010
1,024
1,038
1,053
1,067
17.93
18.28
18.63
18.98
19.33
255
260
265
270
275
3,627
3,698
3,769
3,840
3,911
1.12
1.20
1.27
1.34
1.41
16
17
18
19
20
227.57
241.79
256.01
270.24
284.46
5.34
5.41
5.48
5.55
5.62
76
77
78
79
80
1,081
1,095
1,109
1,124
1,138
19.69
20.04
20.39
20.74
21.09
280
285
290
295
300
1.48
1.55
1.62
1.69
1.76
21
22
23
24
25
298.68
312.91
327.13
341.35
355.58
5.69
5.77
5.84
5.91
5.98
81
82
83
84
85
1,152
1,166
1,181
1,195
1,209
21.80
22.50
23.20
23.90
24.61
1.83
1.90
1.97
2.04
2.11
26
27
28
29
30
369.80
384.02
398.24
412.47
426.69
6.05
6.12
6.19
6.26
6.33
86
87
88
89
90
1,223
1,237
1,252
1,266
1,280
2.18
2.25
2.32
2.39
2.46
31
32
33
34
35
440.91
455.14
469.36
483.58
497.81
6.40
6.47
6.54
6.61
6.68
91
92
93
94
95
2.53
2.60
2.67
2.74
2.81
36
37
38
39
40
512.03
526.25
540.47
554.70
568.92
6.75
6.82
6.89
6.96
7.03
2.88
2.95
3.02
3.09
3.16
41
42
43
44
45
583.14
597.40
611.59
625.81
640.04
3.23
3.30
3.37
3.45
3.52
46
47
48
49
50
3.59
3.66
3.73
3.80
3.87
3.94
4.01
4.08
4.15
4.22
®
lbs./in.2
205 to 700
kgs./cm2
lbs./in.2
1,620 to 2,800
kgs./cm2
lbs./in.2
lbs./in.2
kgs./cm.2
10,098
10,241
10,383
10,525
10,667
113.90
115.30
116.71
118.12
119.52
1,620
1,640
1,660
1,680
1,700
23,041
23,326
23,610
23,895
24,179
760
770
780
790
800
10,809
10,952
11,094
11,236
11,378
120.93
122.33
123.74
125.15
126.56
1,720
1,740
1,760
1,780
1,800
24,464
24,748
25,032
25,317
25,601
56.95
57.65
58.35
59.06
59.76
810
820
830
840
850
11,521
11,663
11,805
11,947
12,090
127.96
129.36
130.76
132.18
133.58
1,820
1,840
1,860
1,880
1,900
25,886
26,170
26,455
26,739
27,024
3,982
4,054
4,125
4,196
4,267
60.46
61.17
61.87
62.57
63.28
860
870
880
890
900
12,232
12,374
12,516
12,658
12,801
134.99
136.39
137.80
139.21
140.61
1,920
1,940
1,950
1,980
2,000
27,308
27,593
27,877
28,162
28,446
310
320
330
340
350
4,409
4,551
4,694
4,836
4,978
63.98
64.68
65.39
66.09
66.79
910
920
930
940
950
12,943
13,085
13,227
13,370
13,512
142.02
143.43
144.83
146.24
147.64
2,020
2,040
2,060
2,080
2,100
28,730
29,015
29,299
29,584
29,868
25.31
26.01
26.72
27.42
28.12
360
370
380
390
400
5,120
5,263
5,405
5,547
5,689
67.49
68.20
68.90
69.60
70.31
960
970
980
990
1,000
13,654
13,796
13,939
14,081
14,223
149.05
150.46
151.86
153.27
154.67
2,120
2,140
2,160
2,180
2,200
30,153
30,437
30,722
31,006
31,291
1,294
1,309
1,323
1,337
1,351
28.83
29.53
30.23
30.93
31.64
410
420
430
440
450
5,831
5,974
6,116
6,258
6,400
71.71
73.12
74.52
75.93
77.34
1,020
1,040
1,060
1,080
1,100
14,507
14,792
15,076
15,361
15,645
156.08
157.49
158.89
160.30
161.71
2,220
2,240
2,260
2,280
2,300
31,575
31,860
32,144
32,428
32,713
96
97
98
99
100
1,365
1,380
1,394
1,408
1,422
32.34
33.04
33.75
34.45
35.15
460
470
480
490
500
6,543
6,685
6,827
6,969
7,112
78.74
80.15
81.56
82.96
84.37
1,120
1,140
1,160
1,180
1,200
15,930
16,214
16,499
16,783
17,068
163.11
164.52
165.92
167.33
168.74
2,320
2,340
2,360
2,380
2,400
32,997
33,282
33,566
33,851
34,135
7.38
7.73
8.09
8.44
8.79
105
110
115
120
125
1,493
1,565
1,636
1,707
1,778
35.86
36.56
37.26
37.97
38.67
510
520
530
540
550
7,254
7,396
7,538
7,680
7,823
85.77
87.18
88.59
89.99
91.40
1,220
1,240
1,260
1,280
1,300
17,352
17,637
17,921
18,205
18,490
170.14
171.55
172.95
174.36
175.77
2,420
2,440
2,460
2,480
2,500
34,420
34,704
34,989
35,273
35,558
654.26
668.48
682.70
696.93
711.15
9.14
9.49
9.84
10.19
10.55
130
135
140
145
150
1,849
1,920
1,991
2,062
2,133
39.37
40.07
40.78
41.48
42.18
560
570
580
590
600
7,965
8,107
8,249
8,392
8,534
92.80
94.21
95.62
97.02
98.43
1,320
1,340
1,360
1,380
1,400
18,774
19,059
19,343
19,628
19,912
177.16
178.56
180.00
181.37
182.78
2,520
2,540
2,560
2,580
2,600
35,842
36,126
36,411
36,695
36,980
51
52
53
54
55
725.37
739.60
753.82
768.04
782.27
10.90
11.25
11.60
11.95
12.30
155
160
165
170
175
2,205
2,276
2,347
2,418
2,489
42.89
43.59
44.29
45.00
45.70
610
620
630
640
650
8,676
8,818
8,960
9,103
9,245
99.84
101.24
102.65
104.05
105.46
1,420
1,440
1,460
1,480
1,500
20,197
20,481
20,766
21,050
21,335
184.19
185.59
187.00
188.40
189.81
2,620
2,640
2,660
2,680
2,700
37,264
37,549
37,833
37,118
38,402
56
57
58
59
60
796.49
810.71
824.93
839.16
853.38
12.66
13.01
13.36
13.71
14.06
180
185
190
195
200
2,560
2,631
2,702
2,773
2,845
46.40
47.11
47.81
48.51
49.21
660
670
680
690
700
9,387
9,529
9,672
9,814
9,956
106.87
108.27
109.68
111.08
112.49
1,520
1,540
1,560
1,580
1,600
21,619
21,903
22,188
22,472
22,757
191.22
192.62
194.03
195.43
196.84
2,720
2,740
2,760
2,780
2,800
38,687
38,971
39,255
39,540
39,824
kgs./cm.2
lbs./in.2
BIV-65
CONVERSION CHART - PRESSURE
1 kgs./cm2 = 14.223 lbs./in.2
WEIGHT CONVERSION
WEIGHT CONVERSION
POUNDS TO KILOGRAMS
(1 pound = 0.4536 kilogram)
Pounds
0
1
2
3
4
5
6
7
8
9
0
10
20
30
40
50
60
70
80
90
0.00
4.54
9.07
13.61
18.14
22.68
27.22
31.75
36.29
40.82
0.45
4.99
9.53
14.06
18.60
23.13
27.67
32.21
36.74
41.28
0.91
5.44
9.98
14.52
19.05
23.59
28.12
32.66
37.20
41.73
1.36
5.90
10.43
14.97
19.50
24.04
28.58
33.11
37.65
42.18
1.81
6.35
10.89
15.42
19.96
24.49
29.03
33.57
38.10
42.64
2.27
6.80
11.34
15.88
20.41
24.95
29.48
34.02
38.56
43.09
2.72
7.26
11.79
16.33
20.87
25.40
29.94
34.47
39.01
43.55
3.18
7.71
12.25
16.78
21.32
25.86
30.39
34.93
39.46
44.00
3.63
8.16
12.70
17.24
21.77
26.31
30.84
35.38
39.92
44.45
4.08
8.62
13.15
17.69
22.23
26.76
31.30
35.83
40.37
44.91
KILOGRAMS TO POUNDS
(1 kilogram = 2.2046 pounds)
Kilograms
0
10
20
30
40
50
60
70
80
90
BIV-66
0
0.00
22.05
44.09
66.14
88.18
110.23
132 28
154.32
176.37
198.41
1
2.20
24.25
46.30
68.34
90.39
112.43
134.48
156.53
178.57
200.62
2
3
4.41
26.46
48.50
70.55
92.59
114.64
136.69
158.73
180.78
202.82
6.61
28.66
50.71
72.75
94.80
116.84
138.89
160.94
182.98
205.03
4
5
6
7
8
9
8.82
30.86
52.91
74.96
97.00
119.05
141.09
163.14
185.19
207.23
11.02
33.07
55.12
77.16
99.21
121.25
143.30
165.35
187.39
209.44
13.23
35.27
57.32
79.37
101.41
123.46
145.50
167.55
189.60
211.64
15.43
37.48
59.52
81.57
103.62
125.66
147.71
169.75
191.80
213.85
17.64
39.68
61.73
83.77
105.82
127.87
149.91
171.96
194.00
216.05
19.84
41.89
63.93
85.98
108.03
130.07
152.12
174.16
196.21
218.26
®
CROSS REFERENCE CHART
CROSS REFERENCE CHART
GATE - GLOBE - CHECK
KITZ
CRANE
09
10
11
12
7TF
1310
1
-
HAMMOND MILWAUKEE
IB413T
IB423
IB-440
IB-418
590T
1590T
502
1502
NIBCO
RED-WHITE
STOCKHAM
T235-Y
S-235-Y
T-211-B
-
221
211
212
B22T
B24T
B-16
B-17
17
362e
IB412
572
T-275-B
-
B-66
17S
382P
IB444
593A
T-276-AP
-
B-74
18
229C
-
-
T-275-Y
-
B-32
19
76E
IB949
507
T-473-B
-
B-375
22
37
IB904
509
T-413-B
236
B-319
22T
41
IB940
-
T-413-Y
236T
B-320-T
23
1342
IB912
1509
S-413-T
237
B-309
23T
-
-
-
S-413-Y
237-T
B-310-T
24
428
IB640
148
T-111
208
B-100
25
431
IB641
1150
T-131
209
B-122
27
-
-
-
-
206F
-
28
-
-
-
-
207F
-
29
137
-
-
T-433-B
239
B-321
30
-
-
-
S-433-B
-
-
37
-
IB652
1182
T174-A
-
B-144
40
438
IB645
105
T-113
280
B-103
41
1324
IB647
115
S-113
281
B-104
42
431UB
IB629
1151
T-134
298
B-120
43
-
IB648
1169
S-134
299
B-124
44
-
IB635
149
S-111
208-C
B-108
45
1334
IB646
-
-
-
-
46
437
IB646
1140
T-133
204
B-128
64
1324
IB638
-
-
-
-
72
465-1/2
IR1140
F-2885
F-617-O
421
G-623
73
475-1/2
IR1146
F-2890
F-617-ON
422
G-613
75
461
IR1138
F-2882
F-619
415
G-612
76
351
IR116
F-2981
F-718-B
400
G-512
78
373
IR1124
F-2974
F918-B
435
G-931
Chart indicates comparable figure numbers of other manufacturers’ products of similar design or use and should only be
used as a guide, some variation in detail is possible.
®
BIV-67
! CAUTION
U
Pressure-temperature ratings and other performance data published
in this catalog have been developed from our design calculation,
in-house testing, field reports provided by our customers and/or published official standards or specifications. They are good only to
cover typical applications as a general guideline to users of KITZ
products introduced in this catalog.
For any specific application, users are kindly requested to contact
KITZ Corporation for technical advice, or to carry out their own study
and evaluation for proving suitability of these products to such an
application. Failure to follow this request could result in property
damage and/or personal injury, for which we shall not be liable.
While this catalog has been compiled with the utmost care, we
assume no responsibility for errors, impropriety or inadequacy. Any
information provided in this catalog is subject to change without
notice for error rectification, product discontinuation, design modification, new product introduction or any other cause that KITZ
Corporation considers necessary. This edition cancels all previous
issues.
! WARNING
U
This product contains a chemical known to the State of California to
cause cancer, or birth defects or other reproductive harm.
ISO 9001 Certified since 1989
®
10750 CORPORATE DRIVE • STAFFORD, TEXAS 77477 U.S.A.
PHONE (281) 491-7333 • TOLL FREE (800) 772-0073 • FACSIMILE (281) 491-9402
Visit our web site at: www.kitz.com
— Distributed by —

KITZ CORPORATION OF AMERICA

Transcription

Similar documents

Stainless and High Alloy Steel Valves