2 MB 1st Aug 2014 Kaba Simplex EE1000 Series

EE1000 SERIES
INSTALLATION INSTRUCTIONS
Kaba Access Control
2941 Indiana Avenue Winston-Salem, NC 27105 USA
Tel: (800) 849-8324 (336) 725-1331
Fax: (800) 346-9640 (336) 725-3269
www.kabaaccess.com
PKG2282 0307
Important: Please keep these instructions. The combination of this lock has
been factory preset: 2 and 4 pressed together, then 3.
Table of Contents
Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
WARNING
For your own safety, you must change the combination at the time of
installation.
Determining the Hand of Your Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
A.
Marking the door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
B.
Drilling the holes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
C.
Installing the latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
D.
Adjusting the lock for doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
E.
Changing the hand of the lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
F.
Aligning the outside lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
G.
Testing the operation of the outside lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
H.
Installing the outside lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
I.
Installing the inside lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
J.
Testing the operation of the inside lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
K.
Installing the strike . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
L.
Changing the combination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
M.
Preserving the latch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
N.
Combination setting record . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
O.
Clearing a lost combination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
P.
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
PLEASE READ AND FOLLOW ALL DIRECTIONS CAREFULLY
Since every installation is unique, carefully check windows, frame, door, etc. to
ensure that the recommended procedures will not cause damage. KABA is not
responsible for any damage caused by installation.
Tools Required
Electric drill (variable speed)
Awl or center punch
2 1⁄8" (54 mm) Hole saw with pilot drill
1" (25 mm) Hole saw with pilot drill
1⁄4" (6 mm) Drill bit
1⁄2" (12 mm) Drill bit
1" (25 mm) Wood chisel
Hammer
Phillips head screwdriver
Small flat blade screwdriver
Pliers (2)
Template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .center of book
Warranty card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .center of book
Caution: Wear safety glasses when preparing door.
For your records
Model #: __________
Date Purchased: ____________
Dealer: ____________________
Name: __________________
Telephone: ______________________
For technical assistance please call
1-800-849-TECH (8324) or 336-725-1331
1
CHECKLIST
A. MARKING THE DOOR
Use this checklist to make sure that
everything has been included. A) Outside lock housing assembly
Door to frame relationship is critical for the performance and durability of the
latch mechanism. The vertical and horizontal center lines are important when
positioning the lock, and must be according to ANSI* standard A115.2.
B) Inside lock housing assembly
A-1
Fold the paper template (found in the middle of this booklet) along the
line as indicated.
A-2
Tape the template securely to the door so that all the indicated folds are
properly aligned with the high beveled edge of the door.
C) Latch
Screw/accessory pack:
a) strike box
b) strike plate
c) #10 size insert bit for “D”
d) anti tamper spanner screws
e) extra spacer, 1⁄4" (6 mm)
f) torx anti-tamper screw
g) torx bit for “F”
h) four 8-32 x 3⁄4" (19 mm) Phillips combination
screws (for latch & strike)
i) four 8-32 x 11⁄16" (17 mm) Phillips
sems screws (for spacer)
j) four 8-32 x 3⁄16" (5 mm) Phillips
a
sems screws (for spacer)
k) pick for combination change
b
l) rubber bumpers
h
m) angle bracket
n) extra cross pins
o) two Phillips break-off screws
(for mounting outside lock and
m
angle bracket “M”)
A
B
Caution: When a frame has an existing strike, be sure to locate the strike template so that the latch hole center (A) is directly aligned with the center of the
strike cutout.
B
Mark the door using an awl or center punch
as indicated on the template for the 6 holes
to be drilled (See Figure 1-1).
A-4
Remove the template.
d
B. DRILLING THE HOLES
g
e
f
k
1-1
B-1
Use a hole saw with a pilot drill bit to drill the 2 1⁄8" (54 mm) hole (A):
apply pressure evenly until the circular blade cuts the first side of the
door and the tip of the pilot bit emerges through the other side, then
stop.
B-2
Drill through the other side of the door until the 2 1⁄8" (54 mm) circular
hole (A) is completed.
B-3
Use standard drilling bits to drill the two 1⁄2" (12 mm) holes (B) above the
2 1⁄8" (54 mm) hole.
B-4
Use standard drilling bits to drill the two 1⁄4"
(6 mm) holes (C) below the 2 1⁄8" (54 mm)
hole.
B-5
Drill the final 1" (25 mm) hole (D) for the
latch through the edge of the door. Drill until
the hole saw is visible through the 2 1⁄8" (54
mm) hole (A), then stop (See Figure 2-1).
j
l
o
n
Warranty card
A
*ANSI — American National Standards Institute.
Contact KABA for further information.
c
i
A-3
The template is included in the middle of this booklet.
B
A
D
C
2-1
2
3
For doors 2" to 2 1⁄4" (51-57 mm) thick, adjust
the lock as follows:
C. INSTALLING THE LATCH
C-1
C-2
C-3
C-4
Insert the latch into the 1" (25 mm) hole until
the face plate butts up against the door
edge. Make sure the bevel of the latch bolt
(A) faces the same direction as the door
swings to close (See Figure 3-1).
If necessary, draw a line around the face
plate, then remove the latch. Use a sharp 1"
(25 mm) wood chisel to remove approximately 1⁄8" (3mm) of material or enough for
the face plate to be perfectly flush with the
edge of the door.
(A)
D-8
Remove the back plate assembly (AA) from
the outside lock housing by removing the six
back plate screws. One of the screws may be
under the serial number stickers.
D-9
Remove the cylindrical drive unit (CC) from
the back plate assembly (AA) by removing the 4-2
four Phillips head sems screws (EE) from the
underside of the back plate.
A
3-1
(AA)
D-10 Insert the extra spacer provided in the accessory pack (item “E” on the checklist)
between the cylindrical drive unit (CC) and
the back plate assembly (AA).
Insert the latch into the 1" (25 mm) hole in
the door edge until the latch face plate is
flush with the door edge (See Figure 3-2).
D-11
Secure the latch to the door with two of the
3⁄4" (19 mm) screws provided (item “H” on
checklist).
A
(EE)
(BB)
Remount the cylindrical drive unit (CC) onto
(CC)
the back plate assembly (AA) using the four 4-3
11⁄16" (17 mm) Phillips head sems screws provided in screw pack (item “I” on checklist).
(DD)
3-2
D-12 Add a cross pin (item “N” on the checklist) in position A on the drive
shaft (DD) of the outside lock housing (See Figure 4-3).
D. ADJUSTING THE LOCK
The EE1000 Series lockset has been preassembled at the factory to accommodate doors 1 1⁄8" (44 mm) thick.
For doors 1 1⁄2" (38 mm) thick, adjust lock as follows:
D-1
D-2
Remove the back plate assembly (AA) from
the outside lock housing by removing the six
back plate screws. One of the screws may be
under the serial number sticker.
Remove the cylindrical drive unit (CC) from
the back plate assembly (AA) by removing
the four Phillips head sems screws (EE) from
the underside of the back plate (AA).
(EE)
(BB)
Note: Unless otherwise stated, all locks are factory assembled for left hand
operation (A) (See Figure 5-2). Use the following procedure to change the
hand of the lock to right hand operation (B) 5-2.
E-1
(CC)
4-1
(DD)
Remove (and discard) the spacer (BB) located between the back plate
assembly (AA) and the cylindrical drive unit (CC) .
D-4
Remount the cylindrical drive unit (CC) onto the back plate assembly
(AA) using the four 8-32 X 3⁄16" (5 mm) shorter Phillips head sems
screws provided in the screw pack (item “J” from the checklist).
D-5
Remove the cross pin from position B on the drive shaft (DD).
D-6
Reposition the cross pin in position C on the drive shaft (DD). Drive shaft
pins should be vertical.
4
Warning: Damage may result if the knob hits against either the wall or the wall
stop. In such a case, ALL warranties are null and void.
E. CHANGING THE HAND OF THE LOCK
(AA)
D-3
D-7
D-13 Remount the back plate assembly (AA) onto the outside lock housing.
Remove the back plate assembly (A) from
the outside lock housing by removing the
four back plate screws (See Figure 5-1).
E-2
Unscrew the four Phillips head sems screws
(B) on the underside of the body plate and
remove the cylindrical drive unit (C) from the
back plate assembly (A).
E-3
Turn the cylindrical drive unit (C) so that the
cutout for the latch (D) faces the opposite
direction (180°).
A
C
D
B
5-1
E-4
Reattach the cylindrical drive unit (C) to the back plate assembly (A)
using the four Phillips head screws removed in step 2.
E-5
Remount the back plate assembly onto the front lock housing assembly.
Reinstall the back plate assembly (AA) onto the outside lock housing.
5
E-6
Tighten all four screws securely.
E-7
Test the lock to make sure it is still working
properly (see page 16 “Testing the operation
of the outside lock”).
H. INSTALLING THE OUTSIDE LOCK
A
H-1
H-2
B
5-2
F. ALIGNING THE OUTSIDE LOCK
H-3
F-1
F-2
Place the outside lock unit on the door so
the screw studs (A) pass through the two 1⁄2"
(13 mm) holes (See Figure 6-1 & 6-2).
Align the latch tailpiece (A) with the shoe
retractor (B) of the cylindrical drive unit (D)
by depressing the latch bolt slightly. Make
sure that the latch prongs (C) and cylindrical
drive unit (D) engage each other (See Figure
6-3).
13⁄8" (35mm)
Shorten the Phillips screws (item “D” on
checklist) if necessary by breaking off at the
score marks (See Figure 8-1).
Insert the two Phillips head screws (A)
through the angle bracket (B) and into the
two 1⁄4" (6 mm) holes in the door (See
Figure 8-2).
13⁄4" (45mm)
2" (51mm)
8-1
B
A
Tighten the Phillips head screws (A), securing the outside lock assembly to the door
(See Figure 8-3).
8-2
A
6-1
8-2
A
I. INSTALLING THE INSIDE LOCK
6-2
A
I-1
Place the inside lock housing (C) as shown in
figure 10-1. Make sure the drive shaft pin (B)
enters the corresp-onding vertical slot (A) of
the drive sleeve (See Figure 9-1 & 9-2).
I-2
Use the #10 insert bit (B) included in the
accessory pack (item “C” on checklist) to
screw in the two anti-tamper spanner type
screws (A) (item “D” on checklist) through
the face of the inside lock (See Figure 9-3).
C
A
B
9-1
B
C
G. TESTING THE OPERATION OF
THE OUTSIDE LOCK
C
G-1
Turn the outside knob clockwise to the stop
position then release it.
G-2
Enter the factory-set combination: Depress
buttons 2 and 4 at the same time (release),
then depress button 3 (release). You should
feel a “click” as each button is depressed.
G-3
Turn the outside knob clockwise to the stop
position and hold. Make sure the latch is
fully retracted, flush with the doors edge.
G-4
Release the knob. The latch should return to
the fully extended position.
D
6-3
9-2
A
B
7-1
9-3
6
7
Kaba Access Control warrants this product to be free from defects in material
and workmanship under normal use and service for a period of one (1) year.
Kaba Access Control will repair or replace, at our discretion, locks found by
Kaba Access Control analysis to be defective during this period. Our only liability, whether in tort or in contract, under this warranty is to repair or replace
products that are returned to Kaba Access Control within the one (1) year warranty period.
NO POSTAGE
NECESSARY
IF MAILED
IN THE
UNITED STATES
KABA SIMPLEX®
LIMITED WARRANTY
The RGA number must be included on the address label when material
is returned to the factory. All component parts including latches and strikes
(even if not inoperative) must be included in the package with return. All
merchandise must be returned prepaid and properly packaged to the address
indicated.
KABA ACCESS CONTROL
2941 INDIANA AVENUE
WINSTON-SALEM, NC 27199-3770
WINSTON-SALEM, NC
POSTAGE WILL BE PAID BY ADDRESSEE
Authorization to Return Goods
Returned merchandise will not be accepted without prior approval. Approvals
and Returned Goods Authorization Numbers (RGA Numbers) are available
through our Customer Service department in Winston-Salem, NC
(800) 849-8324. The serial number of a lock is required to obtain this RGA
Number. The issuance of an RGA does not imply that a credit or replacement
will be issued.
PERMIT NO. 1563
The environment and conditions of use determine the life of finishes
on Kaba Access Control products. Finishes on Kaba Access Control products
are subject to change due to wear and environmental corrosion. Kaba Access
Control cannot be held responsible for the deterioration of finishes.
FIRST-CLASS MAIL
ATTENTION: This warranty does not cover problems arising out of improper
installation, neglect or misuse. All warranties implied or written will be null and
void if the lock is not installed properly and / or if any supplied component part
is substituted with a foreign part. If the lock is used with a wall bumper, the
warranty is null and void. If a doorstop is required, we recommend the use of a
floor secured stop.
BUSINESS REPLY MAIL
This warranty is in lieu of and not in addition to any other warranty or condition, express or implied, including without limitation merchantability, fitness for
purpose or absence of latent defects.
Name
Position
Company
Address
City
State
Phone
Email
Lock Model Number
Date of Purchase
Name of Dealer Purchased From
ZIP (Postal Code)
Country
Thank you for purchasing our product. In order to
protect your investment and to enable us to better
serve you in the future, please fill out this registration
card and return it to Kaba Access Control, or
register online at www.kabaaccess.com.
REGISTRATION CARD
Notes
Commercial Building
College/University
Hospital/Healthcare
Other (please specify)
Government/Military
Industrial / Manufacturing
This lock will be used in what type of facility?
Airport
School/Educational
What area is being secured with this lock? (e.g. Front Door, Common Door, Exercise Room)
Replacing a Keyless Lock other than Kaba
Replacing a Kaba Electronic Access Control
Replacing a Kaba Mechanical Pushbutton Lock
Replacing a conventional keyed lock
New Installation
This lock is:
Internet / Web
Training Class
Another Use
Other (please specify)
How did you learn about Kaba Access Control Pushbutton Locks?
Advertisement Previous Use
Locksmith
Maintenance
What was your reason for buying this lock?
Who installed your lock?
Locksmith
Maintenance
Other
Check here if you would like more information on Kaba Access Control locks.
I-3
Use the torx anti-tamper tool bit included in
the accessory pack (item “G” on checklist) to
install the anti-tamper torx-type screw (A)
(item “F” on checklist) through the bottom
of the lock into the angle bracket (See
Figure 9-4).
Caution: Check the operation of the latch by making
sure that the dead latch stops against the strike
plate, and does not slip into the strike opening
when the door is closed (A) (See Figure 11-2).
If this situation occurs, then a total lockout may
result. This will cancel our warranty of the complete
lock mechanism.
A
9-4
Note: If there is a gap between the edge of door
and the frame (or in the case of double doors,
the edge of the door and the edge of the door)
of more than 1⁄4" (6 mm) the dead latch will fail
to engage the strike plate.
J. TESTING THE OPERATION OF THE INSIDE LOCK
J-1
Turn the inside knob all the way until it stops, then release it.
J-2
Enter the factory set combination: depress
buttons 2 and 4 simultaneously (release),
then depress button 3 (release) (See Figure
10-1).
J-4
Turn the knob clockwise to the stop
position. As the knob turns, the latch will
retract. Make sure the latch retracts fully
(flush with the latch face plate).
The door must be open.
10-1
Release the knob. The latch will return to the fully extended position.
Mark the location of the strike on the door
frame (A) according to the template. Make
certain that the line through the screw holes
of the strike are aligned with the line through
the screw holes on the face of the latch
when the door is closed (See Figure 11-1).
The combination for the outside and inside locks must be changed independently. Follow the same procedure for the outside and inside.
L-1
Use the torx anti-tamper tool bit provided
item "G" on checklist to remove the tamperproof screw from the top of the pushbutton
housing (See Figure 12-1).
L-2
Turn the knob clockwise to the stop position,
then release.
A
K-3
8
12-1
B
L-3
Enter the existing combination. On new installations, enter the factoryset combination: depress buttons 2 and 4 simultaneously (release), then
depress button 3 (release). You should feel a “click” as each button is
depressed.
L-4
Insert the pick provided (item “K” on checklist) through the screw hole and lightly
depress the slide inside — you will feel a
slight “click”. Remove the pick (See Figure
12-2).
L-5
Turn the knob clockwise all the way until it
stops, then release.
C
K-2
A
L. CHANGING THE COMBINATION
K. INSTALLING THE STRIKE
K-1
11-2
If necessary, correct the door over-travel by using the rubber bumpers as
described in the "Preserving the latch" section 14.
B
J-3
D
Mortise the door frame (for strike box) to a
E
minimum depth of 3⁄4" (19 mm). This will
11-1
guarantee that the latch (D) can be fully
extended into the door frame if using an optional 3⁄4" (19 mm) throw
latch. (The supplied KABA strike box must be used).
Place the strike box (B) in the mortised cutout. Secure the strike plate
(C) with two of the 3⁄4" (19 mm) screws (E) provided (item “H” on checklist). If necessary, draw a line around the strike. Use this line as a guide
to cut out a minimum of 1⁄16" (2 mm) of material or enough to make the
strike plate flush with the door frame.
A
12-2
9
L-6
Note: You can use one button or all five for a
combination, but each button can only be used
once. You can press two buttons simultaneously
as a step in the combination.
L-7
This condition can be prevented by adding bumpers to the door stop.
Choose your new combination, write it on
page 28, then enter the new combination —
press buttons carefully (a slight click should
be felt as each button is depressed) (See
Figure 12-3).
Turn the knob clockwise once, to the stop
position, hold in position and make sure the
latch is retracted. Release the knob. Turn the
knob clockwise again to the stop position. At
this point, the latch should not retract unless
you enter the new combination
(See Figure 12-4).
* American National Standards Institute — contact KABA for further information.
Installing Rubber Bumpers (provided in accessory pack – item “L” on checklist)
L-9
Repeat steps 1-8 for other side of door.
M. PRESERVING THE LATCH
When the door rests against the door stop (A), the
dead latch (B) should seat against the strike plate.
At this point, you will notice a tolerance of 3⁄32" (2
mm), basic according to ANSI standards. If the door
travels beyond this tolerance, the dead latch may
slip into the strike box with the anti-friction device,
causing the latch to jam, and create a lock-in and
lock-out condition (See A in Figure 13-2).
M-2
Standing on the door stop side of the door,
check for gaps between the door and the
door stop on all three sides of the frame
(left, right, and top). Mark locations where
the gaps are approximately 3⁄16" (5 mm) (See
Figure 13-3).
M-3
Make sure these locations are free of grease
and dust.
M-4
Peel the bumpers from their protective backing without touching the adhesive surface
and stick them on the marked locations on
the door stop.
M-5
Allow 24 hours for adhesive to set before
testing. Door may be operated normally during this time.
12-4
Replace the tamperproof screw in the top of the lock unit.
Rubber bumpers (supplied with the lock) may be
required to properly align the door. The adjustment
becomes more significant with metal frames, wood
doors, and filler plates when replacing existing
hardware. Figure 13-1 shows the proper alignment
between the door, the frame, the latch and the
strike plate.
Close door and apply pressure making sure
the dead latch rests on the strike plate.
12-3
L-8
The door to frame relationship is critical for the
performance and durability of the latch mechanism. The vertical and horizontal center lines are
important when positioning the lock, the strike, and
the latch, and must be according to ANSI* standard
A115.2. To insure proper installation, you must use
the supplied strike plate.
M-1
A
1 15⁄16" (49mm)
⁄32"
(2mm)
11
⁄32"
(9mm)
13-3
3
1 ⁄4" (44mm)
3
N. COMBINATION SETTING RECORD
Combination #
B
Date
13-1
A
13-2
10
11
O. CLEARING A LOST
COMBINATION
There is no procedure for finding an unknown combination from the front of the lock. A lost combination must be cleared by removing the combination
chamber from the lock housing, then a new combination can be set.
A
B
C
E
Note: The following procedures can be used for
both the inside and outside lock assemblies.
O-1
O-2
D
Remove the back plate from the lock by
removing the four back plate screws.
Lift the chamber linkage (A) off of the control shaft (B) by prying up with a flat blade
screwdriver (See Figure 14-1).
O-3
Remove the shaft bushing (C).
O-4
Remove the combination chamber (D) by
removing the two Phillips head screws (E) at
each end of the combination chamber.
14-1
O-8
Depress the lockout slide (E). The gears (D)
are now free to rotate (See Figure 14-6).
O-9
Turn each gear (D) so that the gear pockets
(F) are aligned (See Figure 14-6).
E
D
O-10 Return the unlocking slide (C) over the
unlocking slide stud (A) while making certain
the five toes (G) are engaged in the five gear
pockets (F). If necessary, adjust each gear to
make proper alignment between toes and
gear slots (See Figure 14-6 & 14-7).
14-6
Resecure the “E” ring (B) on the unlocking slide
stud (A). Your chamber now resembles Figure 14-7
and is ready for reassembly into the lock housing.
14-7
B
Do not attempt to set a combination until the complete unit has been reassembled.
A
REASSEMBLING THE LOCK
F
G
B
A
C
A
B
O-5
Remove the 3 sided chamber cover (A)
marked “KABA” (See Figure 14-2) by gently
tapping the lip of the chamber cover at the
control shaft end of the chamber (A) (See
Figure 14-3) with a screwdriver to detach it
from the staked joints (B).
O-11
A
Resecure the chamber cover (A) marked
KABA. Make sure the staked joints (B) on
both end plates fit through both slots on the
back cover (See Figure 14-2). Re-stake
joints.
O-12 Resecure the shaft bushing (B) with flat side
facing up (See Figure 14-8).
B
14-3
C
D
14-8
O-13 Secure the chamber (D) with the two Phillips head screws (E) you
removed earlier (See Figure 14-8).
O-6
Lay the chamber down on its side (See
Figure 14-41).
O-7
With tweezers, or other tool, slide the “E”
B
ring (B) off the unlocking slide stud (A) (See
14-4
Figure 14-4), then gently lift the end of the
unlocking slide (C) over the unlocking slide stud (A).
Note: The unlocking slide (C) is under spring tension and will be easier to lift if pushed to the left
to ease tension. Swing the unlocking slide (C) sufficiently to clear the gears (D), no further than
shown in Figure 14-5.
E
14-2
A
O-14 Resecure the chamber linkage (C) onto the control shaft (F) (See Figure
14-8).
C
O-15 Replace the back plate and secure it with the four back plate screws.
SETTING THE COMBINATION
Perform the following steps in order.
O-16 Turn the outside knob once clockwise to the stop position then release.
D
14-5
O-17 Enter the new combination.
C
O-18 Turn the outside knob clockwise to the stop position, make sure the
latch is fully retracted, then release the knob to lock in the new combination.
O-19 Repeat steps 2 & 3 before closing your door to confirm code setting.
12
13
P. TROUBLESHOOTING
?
Turning outside or inside knob always retracts latch without depressing
any buttons.
Lock is in zero combination.
?
Notes
Follow the procedure for changing a combination (Step 14 on page 26)
except omit step 3 (do not enter the existing combination).
After entering a new combination, the lock works one time only; then the
lock fails to open.
Buttons of intended combination were not fully depressed when changing
combination.
Refer to (Step 17 on page 34) - "Clearing a lost combination".
For technical assistance please call
1-800-849-TECH (8324) or 336-725-1331
14
15