Product Info - 2016 - SDC Switzerland SA, Swiss Dental Care

orthodontic
restorative
SDC Product Line 2016
prophylaxis
The modern solution
from Swissdentacare
Calculated labour costs to reduce 1 mm of enamel
Approximal enamel correction
90 €
55 €
15 €
Manual Strip
Manual File
Mechanical File
Data based on university study (in vitro), where the removal rate of various grinding tools were examined1. On basis
of these results, the time required to remove 1 mm of enamel was calculated. Economically cost covering amounts
per working hour of german dentists were approximately € 180 in 20022,3. Taking this data, the shown costs were
calculated.
Apart from the economic aspect, the mechanical method
ensures substantial advantages
Mechanical
Manual
2
Improved comfort for your patients
• reduced treatment time
(max. 5 min vs min. 15 min)
• reduced treatment stress
Output Optimization
• optimized view on treatment area
• optimized control of the abrasive
1) Manfredi M., Interproximal enamel reduction: SEM ultrasound analysis of various methods; Dissertation, Universita’ degli studi dell’Insubria, 2006/2007
2) Hartenbach M.; Praxiskosten – Was kostet eine Zahnarztstunde; in: Zahnärzte-Wirtschaftsdienst-05/2002
3) „Im Durchschnitt hat eine Ein-Behandler-Praxis einen Kostensatz von 170 – 260 Euro und einen Honorarstundensatz von 290 – 420 Euro:“; aus Tafuro F., Franzen
N.; in: Unternehmen Zahnarztpraxis – Die Bausteine des Erfolgs (S. 76, Kostenquote); Springer-Verlag Berlin, 2011
www.swissdentacare.ch
swissdentacare.ch
For Orthodontic & Aligner treatments
G5-ProLign Starter Kit.
With handpiece
Art. 1300/Kit/L
Sirona T1 Line 11, water & light
Art. 1300/Kit/NSK/X55 NSK Ti Max X55, water
NEW
Handpiece with internal water irrigation
No noise!
No vibration!
Handpiece Maintenance
To guarantee that the products have a long
service-life, please refer to the instructions of
use in manufacturer's web page.
(www.sirona.com / www.nsk.com)
3
We advise
to observe the recommended speed indicated in the table below and manufacturer's
instructions of use.
Micromotor (T1 Line)
ISO attachment
Name:
Article Ref. Type:
Stroke:
Reduction:
NSK Ti Max X55
1972
Water 1,4mm
4:1
SDC-Sirona 11L
1995
Water & Light
1,1mm
2,4:1
Micromotor setting speed:
Recommended max. speed:
40'000 rpm
10'000 rpm
12'000 rpm
5'000 rpm
swissdentacare.ch
For Orthodontic & Aligner treatments
G5-ProLign Files calibrated files for Aligner Systems and fixed orthodontics
G5-ProLign strips are especially suitable for safe, precise, minimally invasive orthodontic preparations. Safe and
comfortable treatment. Excellent tools with calibrated thickness strips, for controlled interproximal correction.
LIZAB
ERI
Name:
Thickness:
Article Ref. 2 sides:
Packaging. refills: G5-ProLignG5-ProLign
0.10 mm
0.20 mm
1310/3 1320/3 3 pcs.
3 pcs.
G5-ProLign
0.30 mm
1330/3 3 pcs.
G5-ProLign
0.40 mm
1340/3 3 pcs.
G5-ProLign
0.50 mm
1350/3 3 pcs.
LIZAB
ERI
G5-ProLign
0.10 mm
1310/1/3 3 pcs.
G5-ProLign
0.20 mm
1320/1/3 3 pcs.
G5-UltraSoft (ultra fine)
0.09 mm 2 sides coated
1106/3 3 pcs.
ST
LE
STE
IZABL
RIL
E
1 side
coated files
Name:
Thickness:
Article Ref. 1 side:
Packaging. refills:
ST
LE
STE
IZABL
RIL
E
2 sides
coated files
G5-ProLign Set
0.1,0.2,0.3,0.4 mm 2 sides coated
1300/S4
4 pcs.
SDC-CombiStrip thin flexible diamond coated strip for mechanical operative mode
LE
LIZAB
ERI
Name:
CombiStrip CombiStrip
Strip hight:
2.5 mm 2 side coated
2.5 mm 1 side coated
Grid:
ultra-finefine
Article Ref.:1800/UF 1800/F
Packaging refills: 3 pcs. 3 pcs.
SDC IPR Products used in vivo
swissdentacare.ch
ST
4
IZABL
RIL
E
Application field:
• Ortho & aligners
•Restorative
STE
Extra thin flexible strip with an ingenious dual operation mode. Excellent for high-gloss polishing of interproximal
areas, enamel, composites, and cements. Ideal smart solution for rounding off the tooth profile after proximal
reduction. Also suitable for removing overhanging sections of composite and cement.
For Orthodontic & Aligner treatments
SDC-G5-ProStrip Interproximal reduction strips with separate shank, for more flexibility.
The click mechanism allows the file to be attached and removed quickly and easily.
NEW
+
Name:
G5-ProStrip
Grid: 15 µm
Article Ref. 2 sides:
1115/3 Article Ref. 1 side:
1115/1/3 Packaging. refills:
3 pcs.
G5-ProStrip
25 µm
1125/3 1125/1/3 3 pcs.
G5-ProStrip
40 µm
1140/3 1140/1/3
3 pcs.
G5-UltraSoft (ultra fine)
6 µm
1106/3
3 pcs.
G5-ProStrip Set
6,15,25,40 µm
1100/S4
4 pcs.
SDC-Measuring gauge
Name:
Measuring Gauge 5
Description:
5 thicknesses to measure the IPR space
Article Ref.:1991
Packaging:
1 pc.
Measuring Gauge 9
9 different thicknesses
1992
1 pc.
SDC-G5 Shank for G5 Instruments.
IZABL
RIL
ST
LE
E
STE
The SDC-G5 Shank is a file holder for use exclusively with all G5 instruments. Autoclavable.
LIZAB
ERI
Name:
G5-Shank Article Ref.:1990/40
Packaging refills:
40 pieces
5
G5-Shank 1990/20
20 pieces
SDC-PolySoft High-gloss polishing after interproximal reduction, restorations, or for prophylaxis treatments
PolySoft is a thin polyester strip with ultra-fine abrasive coating on one side. Excellent for high polishing and finishing of
interproximal areas.
SEM enlargment 500x
SEM enlargment 2000x
Name:
Grid: µm
Article Ref.:
Packaging refills:
SEM picture: Untreated enamel surface and treated surface with PolySoft 15 micron
All pictures by courtesy of the Institute of Material Science: Technische Universität Darmstadt, Germany
swissdentacare.ch
PolySoftPolySoft
Extra - Fine Fine
1209/251215/25
25 pcs.
25 pcs.
For Orthodontic & Aligner treatments
Kits without handpiece
1000 Ortho ProLign Kit
Name:
Description:
Article Ref.:
Packaging:
Ortho ProLign Kit
4 G5-ProLign files 0.1, 0.2, 0.3, 0.4 mm 2 sides coated
2 G5-ProLign files 0.1 and 0.2 mm 1 side coated
2 CombiStrip ultra fine 2 sides coated and fine 1 side coated
1 Measuring Gauge 5
5 Shanks
1000/OrthoProLign
1 pc.
1002 Ortho ProStrip Kit NEW
6
Name:
Description:
Article Ref.:
Packaging:
Ortho ProStrip Kit
3 G5-ProStrip files 15, 25, 40 µm, 2 sides coated
2 G5-ProStrip files 15 and 25 µm, 1 side coated
1 G5-UltraSoft file 6 µm
1 CombiStrip ultra fine, 2 sides coated
1 Measuring Gauge 5
5 Shanks
1002/OrthoProStrip
1 pc.
swissdentacare.ch
Instruction for targeted interproximal enamel reduction for
orthodontic and aligner treatments
Suggestion:
for easier contact point reduction insert a wedge
at first, resolve contact point with the 0.1 mm or 0.2
mm G5-ProLign, expand the interproximal spaces
as desired with the 0.2 mm, 0.3 mm files, etc., in
ascending order, to the desired width.
• Depending on the clinical situation, the widening
of the contact points may be done on one or both
sides.
• For enamel reduction move the strip back and
forward continuously with slight vertical pressure.
How to use step by step ProLign calibrated files
To open
0.1mm
0.2mm
0.3mm
0.4mm
0.5mm
0.1mm
0.2mm
0.2mm
0.2mm
0.2mm
0.3mm
0.4mm
0.4mm
Oscillating Head
Low & moderate
Crowding Set-Up
Wedge:
easier contact point
opening
0.5mm
In contrast to an extraction creating
large gaps, with Interproximal Enamel
Reduction(IPR), the necessary reduction
of enamel is split into several small gaps.
That's why it is, in principle, reasonable also to spread the IPR into several
treatment sessions: firstly, to treat the
easy accessible points of contact and
secondly, to gradually treat the remaining spaces necessary, once the actual
crowding is resolved.
The flattened contact surface additionally
helps reduce a possible recurrence of the
problem. The black triangles occasionally
occurring in the orthodontic treatment of
crowded teeth (increasing interproximal
spaces) maybe counteracted by targeted
contour shaping.
For Orthodontic treatments
SDC-Debonding Kit
Safe removal of adhesive and brackets without damage to the natural tooth structure.
Whereas there is always the risk of damaging the
natural tooth structure with rotary diamond or metallic
instruments, this is eliminated owing to the hardness
of the abrasive grit impregnated into the remover. The
microgrid acts specifically and is embedded in a hard
synthetic rubber matrix. Safe and economical removal of
adhesive residues is possible in a few minutes.
IZABL
RIL
ST
LE
E
STE
Residues after bracket usage can be removed economically and particularly safe in comparison to
the conventional removal techniques of adhesive or
cement residues using diamond rotary or metallic
instruments.
LIZAB
ERI
Set name:
SDC-Debonding-Kit
Article Ref.: 2000/Set
Shank type:
314204204204
Shape: C379
2002/12 2003/122169/6
Size (mm)
023050045045
lengh mm:4,2
8
6
6
swissdentacare.ch
7
For Restoration treatments
SDC-G5-Proxocare
Oscillating diamond-coated files. Proxocare files are particularly suitable for fine preparations and polishing
of proximal and concave restorations. Remove effectively overhanging sections of composites and cements.
Benefits
• Easier access to the interproximal space
as the file is thinner
Class II restorations
Before the restoration, the 60µm
Proxocare corrects easily the contour
of an old neighbouring amalgam (1) .
• No accidental damage to adjacent teeth
• Prevention of surface wave generation
(e.g. caused by rotating instruments)
1
2
3
4
5
6
1
2
3
The 40 or 25µm Proxocare prepare
& bevel the edges of the cavity (2-3).
The Proxocare 6µm polishes damaged porcelain of the adjacent crown
(4).
After the restoration, the different
proxocare files have access to all the
borders of the restoration to adjust
and polish with precision, without
damaging the adjacent hard or soft
tissues (5-6).
Class III, IV, V restorations
The 40 to 25µm Proxocare files are
very useful to prepare, clean & bevel
the edges of the cavity before the
restoration (1) and after eliminating the
excesses following the tooth contour
without creating irregularities like the
action of a bur (2).
The final polishing can be perfectly
realized with the Proxocare 6µm and
the SDC diamond paste (3).
IZABL
RIL
ST
LE
E
STE
8
LIZAB
ERI
Name:
L in mm:
8.5
8.5
Grain in µm:
60
40
References:
1760/3
1740/3
Packaging refills:
3 pcs.
3 pcs.
G5-Proxocare
8.5
8.5
8.5
25
15
6
1725/3
1715/3
1706/3
3 pcs.
3 pcs.
3 pcs.
swissdentacare.ch
Set
all
1700/S5
5 pcs.
For Restoration treatments
SDC G5-ProShape
With non-diamond-coated areas to prevent destruction of proximal contact areas inadvertently
IZABL
RIL
LIZAB
ERI
STE
Name:
Thickness:
Grid
Article Ref. 1 side:
Packaging refills:
G5-ProShape
0.20 mm
medium fine
1600/MF/3
3 pcs.
IZABL
RIL
LE
ST
LIZAB
ERI
For opening inadvertently bonded
proximal contact areas
G5-ProShapeG5-ProShape
0.09 mm
0.15 mm
ultra fine
fine
1600/UF/3 1600/F/3 3 pcs.
3 pcs.
E
G5-ProCut
ST
LE
E
Indications
• Contouring and finishing of proximal
restoration surfaces
• Removal of overhanging sections of
fillings and cement
• Finishing and trimming of proximal
crown margins in gold or ceramic
• To be used with a handpiece
• Uncoated zone to preserve the
contact point
STE
Excellent tools for contouring, finishing and polishing of interproximal areas and subgingival surfaces, will effectively
remove overhanging sections of composites and cements.
G5-ProShape is a unique single-surface diamond-coated metal strip. The strip height (2.5mm) as well as the uncoated
zone preserve the contact point.
Name:G5-ProCut
Article Ref.:1500/3
Packaging refills:
3 pcs.
1001 Resto Kit without handpiece
9
Name:
Description:
Article Ref.:
Packaging:
Resto Kit
3 G5-ProShape files 0.9, 0.15, 0.20 mm 1 side coated
2 CombiStrip ultra fine, 2 sides coated and fine 1 side coated
5 Proxocare files 6, 15, 25, 40, 60 µm, 1 side coated
1 G5-ProCut Saw, 0.10 mm
7 Shanks
1001/Resto
1 pc.
SDC Proxocare animation
swissdentacare.ch
Short Handling Instruction
To fit the strip to the shank with all G5 Instruments
Push the strip from the bottom
side into the shank (3A)
until it clicks in place (3B).
3
Correctly fitted strip in final
position. At the bottom side of the
shank is a little stopper which prevents
the strip from slipping out (3C)
↑
↑
↑
A
C
B
To remove the strip from the shank (for both, blue and Pink shank, with all G5 Instruments)
⤻
4
6
5
Ideal start
hand position
↑
Push down the strip
with your finger (4)
Push down the strip
from shank till it clicks
out (5)
Correctly removed strip
from the shank (6).
Important to know !
We recommend to respect this 3 important points:
1. Do not exceed the recommended working speed! (see table below)
2. Always lubrificate your handpiece after each use
3. Do not attempt to disassemble the handpiece nor tamper with the mechanism
10
NSK Ti- Max X55 4:1
Micromotor:
40’000 rpm
Rec.working speed:
10’000 rpm max.
Sirona T1 11 2,4:1
Micromotor:
12'000 rpm
Rec.working speed:
5’000 rpm max.
Nose Cone 4:1
Micromotor:
20'000 rpm
Rec.working speed:
5’000 rpm max.
Our handpieces work with all Universal ISO motor attachments.
For further information please download operation manuals for NSK at www.nsk-dental.com and for Sirona at www.sirona.com.
swissdentacare.ch
Sterilization and Hygiene recommendation
Files are currently advertised as being sterilizable for repeated use. NB: The nature of particle entrapment
within the grit makes the practice of using recycled files among different patients discretionary. We advise to
always sterilize the files in an autoclave with a cycle B “prion”.
This is in compliance with the EU standard EN13060.
Place the used instruments in
an ultrasonic cleaner with a
special disinfectant containing a
corrosion inhibitor additive.
The instruments should not be
immersed too long in the solution to
ensure that the colour coding is not
removed.
Do not use highly aggressive
chemical products (e.g. hydrochloric
acid, hydrogen peroxide) as they
could corrode the instruments.
These substances can also
impair the technical properties
of the plastics, i.e. change their
hardness and durability.
Program table: Sterilization Cycles Temperature B Standard 134
B Prion 134
135.5º C
135.5º C
B Standard 121
122.5º C
Pressure 2.16 bar
2.16 bar
1.14 bar
Duration of the plateau 4’
18’15’
Duration of the drying phase
15’
15’20’
Total duration: 30’- 40’
44’- 54’
50’- 60’
Please consult our web page to view our company information, instruction for use and further information.
www.swissdentacare.ch
11
swissdentacare.ch
swissdentacare.ch
1252
Some of the products and designations mentioned in the text are patented or copyrighted. The absence of a special reference or the ® sign should not be interpreted as the absence of copyright protection. This publication is copyrighted. All rights,
including those of translation, reprinting, and reproduction (also in the form of extracts) are reserved. No part of this publication may be reproduced or processed using electronic systems in any form or by any means (photocopying, microfilm, or
other methods) without the editor’s prior consent in writing. Colours and products subject to alterations. Printing errors excepted.
SDC CAT-V1a.Eng.MM-2016
SDC Switzerland SA
Via della Posta 3
6934 Bioggio - Switzerland
T +41 91 604 54 13
F +41 91 604 54 14
info@swissdentacare.ch
www.swissdentacare.ch