BMW M3 Forum (E90 E92) - View Single Post

Transcription

3/09/11
BMW M3 Forum (E90 E92) - View Single …
Thread: DIY: E90 Se dan M3 - Side Grill Gill R e m oval & Install
View Single Post
02-07-2009, 08:06 PM
REP1KRR
Ca pta in
DIY: E90 Sedan M3 - Side Grill Gill Removal & Install
This is a step-by-step illustration of how I removed my side gills on my E90 M3.
Drive s: M3
Saloon
Join Date : No v
2006
Locatio n: Sa lt
Lak e C ity
Posts: 753
iTra de r: (1)
Tools needed: painters tape (or another thin/durable tape), small thin flat-head sc rewdriver, T-25 hex/star driver or screwdriver, soft c lean mic rofibe
cloth, and a milk crate or short stool to sit on.
www.m3post.com/forums/showpost.php…
1/13
3/09/11
Use a small thin flat-head screwdriver.
Wrap the screwdriver 3-4 times around with wide painters tape. Clip off the end of the tape close to the head of the screwdriver. This offers a nic e th
point.
2/13
3/09/11
As you insert the tip of the screwdriver between the fender and the furthermost rear area of the side gill, the gill and light assembly will slide forward a
bit offering you a bit more room to get under the plastic.
3/13
3/09/11
Use a soft mic rofiber c loth to protect the paint as you pry the gill out of the honeycomb. This requires a dec ent amount of pressure (reletively speakin
to something plastic) to disengage the plastic c lips/tabs holding it to the honeycomb.
Once the chrome piece has been pulled out enough (maybe 1/4-3/8") grab a hold of the edge of the gill and begin to work it off the honeycomb.
Notice: the placement of the tabs by looking at your new gill. This allows you to apply the pressure in the proper place along the chrome to release th
gill.
4/13
3/09/11
Work your way down the gill (toward the front of the car) applying pressure above & below (top & bottom of the gill) while pulling out (toward you).
DO NOT PIVOT the gill as you're removing/pulling. Work it out TOWARD you. DO NOT bend/pull/forse it out like this, or.....
5/13
3/09/11
...this happens. Casualty!
Not a big deal, bec ause it's hidden, but still bothersome. The pressure of pulling the gill from the back (rear portion, wher
you started) puts too much pressure on the front tabs and the plastic of the honeycomb housing. Work it OUT, TOWARD you.
6/13
3/09/11
PLAY IT SAFE. Place a large piece of painters tape around the wire to prevent it from falling into the fender. Drivers side was shorter/tighter than the
passanger side on my vehicle. I would have hated to lose the wire!
Remove the plug wire (pull up the clip on the plug slightly to release). Remove the screw and remove the light assembly from the chrome gill.
7/13
3/09/11
Ensure the light assembly inserts ALL THE WAY into the new gill. This took a bit of work on one of them. Ensure the light pops out the top of the new
as shown below. Match the appearanc e against the other side of the c ar if necessary.
8/13
3/09/11
Replace the screw in the light assembly. Replace the plug wire. remove the tape.
Test the light is working BEFORE installing the gill.
9/13
3/09/11
Carefully install the gill into the honeycomb. Make certain all tabs/clips are aligned properly in their slots in the honeycomb housing (top & bottom of gi
Ensure all tabs have "CLICKED" <listen> into plac e.
Nicely done!
10/13
3/09/11
Choose your poison.
11/13
3/09/11
Decisions!
Done!
12/13
3/09/11
__________________
M3 Saloon | BBS CH-R | VRS Boo t & Bum pe r | Me iste rschaft GT | AA Pulle y
> com ing soon... Eibach | ESS Supe rcharge r
0
Like
Be the first of your friends to like this.
C lose this window
13/13

BMW M3 Forum (E90 E92) - View Single Post

Transcription

Similar documents

illust-loc-12-acup-pts-save-life-2

BMW ETK installation instruction manual

BMW Isetta - Studio 434

Best Places to Work Genumark

OPTOR IE S May/June 2014

10% OFF*

PERCH DISSECTION pictures to go along with lab

New Transport Models and Smart Use of Transport Infrastructure

2016-07 - RGMotorsport