Flex-Lag® Cold Bond Pulley Lagging

Transcription

Installation, Operation
and Maintenance Manual
Light-Duty
Plain-Pattern
Diamond-Pattern Rubber
Diamond-Pattern Ceramic (13%)
Medium Ceramic (39%)
Full Ceramic (80%)
www.flexco.com
www.flexco.com
Purchase Date:_______________________________________________________________
Purchased From:_____________________________________________________________
Installation Date:_____________________________________________________________
This information will be helpful for any future inquiries or questions
about replacement parts, specifications or troubleshooting.
2
Table of Contents
Section 1 – Important Information........................................................................ 2
1.1General Introduction........................................................................................... 2
1.2User Benefits......................................................................................................... 2
1.3Service Option...................................................................................................... 2
Section 2 – Safety Considerations and Precautions............................................... 3
2.1Stationary Conveyors........................................................................................... 3
2.2 Operating Conveyors........................................................................................... 3
Section 3 – Pre-Installation Checks and Options................................................... 4
3.1Checklist................................................................................................................ 4
Section 4 – Installation Instructions................................................................... 5-8
Section 5 – Pre-Operation Checklist and Testing.................................................. 9
5.1Pre-Op Checklist.................................................................................................. 9
5.2Test Run the Conveyor........................................................................................ 9
Section 6 – Maintenance................................................................................ 10 - 12
6.1New Installation Inspection.............................................................................. 10
6.2Routine Visual Inspection................................................................................. 10
6.3Routine Physical Inspection.............................................................................. 10
6.4Maintenance Log................................................................................................ 11
6.5Lagging Maintenance Checklist....................................................................... 12
Section 7 – Troubleshooting................................................................................. 13
Section 8 – Specs and CAD Drawings............................................................. 13-21
8.1Specifications....................................................................................................... 13
8.2CAD drawing - Light Duty............................................................................... 14
8.3CAD drawing - Plain Rubber............................................................................ 15
8.4CAD drawing - Diamond-Pattern Rubber...................................................... 16
8.5CAD drawing - Diamond Ceramic.................................................................. 17
8.6Medium Ceramic, Dimpled Tiles..................................................................... 18
8.7 Medium Ceramic, Smooth Tiles....................................................................... 19
8.8Full Ceramic, Dimpled Tiles ........................................................................... 20
8.9 Full Ceramic, Smooth Tiles............................................................................... 21
Section 9 – Lagging Adhesives/Toolbox................................................................ 22
Section 10 – Other Flexco® Conveyor Products.................................................... 25
1
Section 1 – Important Information
1.1 General Introduction
We at Flexco® are very pleased that you have selected Flex-Lag® Pulley Lagging for your conveyor system.
This manual will help you to understand the operation of this product and assist you in making it work up to
its maximum efficiency over its lifetime of service.
It is essential for safe and efficient operation that the information and guidelines presented be properly
understood and implemented. This manual will provide safety precautions, installation instructions,
maintenance procedures and troubleshooting tips.
If, however, you have any questions or problems that are not covered, please contact your field representative
or our Customer Service Department:
Customer Service: 1-800-541-8028
Visit www.flexco.com for other Flexco locations and products.
Please read this manual thoroughly and pass it on to any others who will be directly responsible for
installation, operation and maintenance of this pulley lagging. While we have tried to make the installation
and service tasks as easy and simple as possible, it does however require correct installation and regular
inspections to maintain top working condition.
1.2 User Benefits
Correct installation and regular maintenance will provide the following benefits for your operation:
• Eliminate belt slippage
• Reduced conveyor downtime
• Reduced man-hour labor
• Lower maintenance budget costs
• Increased service life for the lagging and pulley
1.3 Service Option
2
Flex-Lag® Pulley Lagging is designed to be easily installed and serviced by your on-site personnel. However, if
you would prefer complete turn-key factory service, please contact your local Flexco Field Representative.
Section 2 – Safety Considerations and Precautions
Before installing and operating Flex-Lag® Pulley Lagging, it is important to review and understand the following safety
information.
There are set-up, maintenance and operational activities involving both stationary and operating conveyors. Each case
has a safety protocol.
2.1 Stationary Conveyors
The following activities are performed on stationary conveyors:
• Installation
• Cleaning
! danger
It is imperative that OSHA/MSHA Lockout/Tagout (LOTO)
regulations, 9 CFR 1910.147, be followed before undertaking
the preceding activities. Failure to use LOTO exposes
workers to uncontrolled behavior of the products caused by
movement of the conveyor belt. Severe injury or death can
result.
Before working:
• Lockout/Tagout the conveyor power source
• Disengage any takeups
• Clear the conveyor belt or clamp securely in place
! WARNING
Use Personal Protective Equipment (PPE):
• Safety eyewear (splash goggles optional)
• NIOSH-approved air respirator with organic
vapor cartridge (if ventilation is not available as
recommended in enclosed Safety Data Sheets)
• Hardhat
• Long-sleeve shirt
• Safety footwear
• Apron (optional)
• Nitrile gloves
Close quarters and heavy components create a worksite
that compromises a worker’s eyes, feet and skull.
PPE must be worn to control the foreseeable hazards
associated with conveyor lagging. Serious injuries can
be avoided.
2.2 Operating Conveyors
There are two routine tasks that must be performed while the conveyor is running:
• Inspection of performance
• Dynamic troubleshooting
! danger
Every belt pulley is an in-running nip hazard. Never
touch or prod an operating pulley. Pulley hazards cause
instantaneous amputation and entrapment.
! WARNING
! WARNING
Never adjust anything on an operating pulley.
Unforseeable belt projections and tears can cause
violent movements. Flailing hardware can cause
serious injury or death.
Pulleys can become projectile hazards. Stay as far from the
pulley as practical and use safety eyewear and headgear.
Missiles can inflict serious injury.
3
Section 3 – Pre-installation Checks and Options
3.1 Checklist
• Check that the lagging size is correct for the pulley width
• Check that the correct amount of lagging strips are available to lag the
pulley (see Page 6).
• Check that the correct amount of primer, adhesive and activator are
available to lag the pulley (see Page 6).
• Check the carton and make sure all the parts are included
• Review the “Tools Needed” list on the top of the installation instructions
• Check the conveyor site:
· Will the lagging be installed in a chute
· Is the install on an open head pulley
Flex-Lag Primer, Adhesive and Activator ONLY for use with
cold-bond rubber-to-rubber or rubber-to-metal adhesion.
4
Section 4 – Installation Instructions
If using non-Flexco® adhesives, please follow that company’s instructions for usage, mixing, application and safety
procedures.
Flex-Lag® Pulley Lagging can be used with Flex-Lag Adhesives. Flex-Lag Adhesives consist of a Primer, Adhesive
and Activator. Before using, the Primer should be thoroughly mixed. Before using, one Adhesive and one Activator
should be thoroughly mixed and used within three hours. Reference the Adhesive Usage Charts on Page 6 for
quantity of each material required based on Pulley Diameter and Face Width.
These materials are meant for use at room temperature. The ambient temperature and temperature of the lagging
and pulley must be between 41˚F-113˚F (5˚C- 45˚C), and the relative humidity should not exceed 80% during the
lagging procedure. These should be checked prior to starting and occasionally during the lagging process to ensure
proper bonding.
Proper protective equipment should be used during the lagging process. Wear safety glasses with side shields.
Wear chemical splash goggles if the possibility exists for eye contact with splashing liquid. Avoid skin contact by
wearing chemically-resistant gloves (nitrile) and long sleeved shirt. An apron may be appropriate if splashing can
occur. Respiratory protection may be required to avoid overexposure when handling this product. If general room
ventilation is not available or sufficient use a NIOSH-approved air purifying respirator with organic vapor cartridge.
Please reference the Safety Data Sheets for Adhesive, Activator and Primer to see detailed requirements. Also, please
follow any local or state guidelines for use of this product.
Physically lock out and tag the conveyor at the power source
before you begin pulley lagging installation.
Tools Needed:
• Grinder (low RPM recommended)
• 24 Grit Flap Disc
• Bench Brush
• Coarse Dish Wheel
• Paint Brushes
•
•
•
•
•
Heavy Duty Knife
Chalk Line
Dead Blow Rubber Hammer
Lagging Stitchers/Rollers
Oscillating Tool (for cutting rubber)
Fig. 1
1. Prepare the pulley by removing the old lagging, paint and primer.
Sand blast the entire pulley or use a grinder with 24 grit flap disc or
paper disc. Use bench brush and non-oil-based metal solvent to clean
remaining particles from the pulley surface. Paint the pulley surface,
including the edges, with Flex-Lag Primer. Allow to dry completely –
a minimum of 30 minutes.
Fig. 2
2. Use a grinder with coarse dish wheel to buff the edges and bottom
of the lagging. Be careful not to smoke the rubber. Wipe with nonoil-based solvent to clean surface of any particles.
5
Section 4 – Installation Instructions (cont.)
3. Use the Strip Selection Chart at right to
calculate the number of strips required for
your pulley diameter. Using a heavy duty
knife, cut lagging strips 4" (100mm) longer
than the pulley face width. Medium and Full
Ceramic lagging come in pre-specified strip
lengths. Note: Do not allow ceramic tiles to
sit at, or over, the edge of the pulley face.
Strip Selection
PULLEY DIAMETER
in.
mm
12.6-15.0
15.1-17.5
17.6-20.0
20.1-22.5
22.6-25.0
25.1-27.5
27.6-30.0
30.1-32.5
32.6-35.0
35.1-37.5
37.6-40.0
40.1-42.5
PULLEY DIAMETER
in.
mm
STRIPS
REQUIRED
320-381
382-445
446-510
511-573
574-636
637-700
701-764
765-827
828-891
892-955
956-1018
1019-1082
6
7
8
9
10
11
12
13
14
15
16
17
42.6-45.0
45.1-47.5
47.6-50.1
50.2-52.6
52.7-55.1
55.2-57.6
57.7-60.1
60.2-62.6
62.7-65.1
65.2-67.6
67.7-70.1
70.2-72.6
STRIPS
REQUIRED
1083-1145
1146-1210
1211-1273
1274-1336
1337-1400
1403-1463
1466-1527
1529-1590
1593-1654
1656-1717
1720-1781
1783-1844
18
19
20
21
22
23
24
25
26
27
28
29
Fig. 3
Adhesive, Activator and Primer Usage Charts
FLEX-LAG® ADHESIVE 0.8L / ACTIVATOR 40g (1:1 mix ratio)
Face Width
Pulley Diameter
In.
8
12
16
20
24
28
32
36
40
44
48
52
56
60
10
14
18
22
26
30
34
38
42
46
50
54
58
62
66
70
74
78
82
86
90
mm
254
356
457
559
660
762
864
965
1067
1168
1270
1372
1473
1575
1676
1778
1880
1981
2083
2184
2286
203
305
406
508
610
711
813
914
1016
1118
1219
1321
1422
1524
1
1
1
1
1
1
2
2
2
2
2
2
2
2
1
1
1
1
2
2
2
2
2
2
3
3
3
3
1
1
1
2
2
2
2
3
3
3
3
3
4
4
1
1
2
2
2
2
3
3
3
4
4
4
4
5
1
1
2
2
2
3
3
3
4
4
4
5
5
5
1
2
2
2
3
3
4
4
4
5
5
5
6
6
1
2
2
3
3
3
4
4
5
5
6
6
6
7
1
2
2
3
3
4
4
5
5
6
6
7
7
8
2
2
3
3
4
4
5
5
6
6
7
7
8
8
2
2
3
3
4
5
5
6
6
7
7
8
9
9
2
2
3
4
4
5
6
6
7
7
8
9
9
10
2
3
3
4
5
5
6
7
7
8
9
9
10
11
2
3
3
4
5
6
6
7
8
9
9
10
11
11
2
3
4
4
5
6
7
8
8
9
10
11
11
12
2
3
4
5
5
6
7
8
9
10
10
11
12
13
2
3
4
5
6
7
8
8
9
10
11
12
13
14
2
3
4
5
6
7
8
9
10
11
12
13
14
14
2
3
4
5
6
7
8
9
10
11
12
13
14
15
3
4
5
6
7
8
9
10
11
12
13
14
15
16
3
4
5
6
7
8
9
10
11
12
13
15
16
17
3
4
5
6
7
8
10
11
12
13
14
15
16
17
FLEX-LAG® PRIMER .75L
Face Width
Pulley Diameter
In.
6
8
12
16
20
24
28
32
36
40
44
48
52
56
60
10
14
18
22
26
30
34
38
42
46
50
54
58
62
66
70
74
78
82
86
90
mm
254
356
457
559
660
762
864
965
1067
1168
1270
1372
1473
1575
1676
1778
1880
1981
2083
2184
2286
203
305
406
508
610
711
813
914
1016
1118
1219
1321
1422
1524
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
1
1
1
1
1
1
1
2
2
2
2
1
1
1
1
1
1
1
1
1
2
2
2
2
2
1
1
1
1
1
1
1
1
1
2
2
2
2
2
1
1
1
1
1
1
1
1
2
2
2
2
2
2
1
1
1
1
1
1
1
1
2
2
2
2
2
2
1
1
1
1
1
1
1
2
2
2
2
2
2
2
Fig. 4a
Fig. 4b
4. Apply first coat of adhesive. Thoroughly mix one can of adhesive and one activator at a time, immediately applying it
to the pulley and strips of lagging. Be sure to apply adhesive to the edges of the lagging as well. This process should use
half of the adhesive/activator required in the chart on Page 6. Note: Allow 4 hours for the first coat to properly cure.
Temperature and humidity will affect dry time.
5. After the first coat of adhesive has dried completely, mark a line across the
pulley face using a chalk line or scriber, ensuring the line is parallel to the
shaft’s centerline and square to the edge of the pulley.
Fig. 5
Fig. 6
6. Apply second coat of adhesive to the pulley. Thoroughly mix one can of
adhesive and activator at a time. From the perpendicular line, apply the
second coat of adhesive to an area slightly greater than one strip of lagging.
Fig. 7
7. Apply a second coat of adhesive to one strip of lagging. Be sure to apply
adhesive to the edges of the lagging as well.
Fig. 8
8. After the second coat has reached the appropriate tackiness (approximately
2-5 minutes, touch with back of hand – feels tacky and leaves no adhesive on
hand) install one strip of lagging, using the perpendicular line to assure the
strip is square to the pulley. Working out from the center of the strip, use a
dead blow rubber hammer for tamping to remove the air gaps, ensuring all
surface area receives one hammer blow. Repeat this process with Lagging
Stitchers/Rollers to remove air gaps from drainage grooves. Be sure to check
edges to verify seal.
7
9. Repeat Steps 6 and 7, then place the second strip of lagging against the first,
taking care to ensure there are no gaps between the lagging. Shift lagging sideto-side to align diamond/ceramic patterns. Additional stitching between strips
may be required to remove any gaps. Repeat the tamping and stitching process
in Step 8 to remove air gaps from the applied strip.
10. Trim the excess lagging from applied strips at the edge of the pulley using a
heavy duty knife or oscillating tool. Trim lagging at an angle up and away from
the pulley edge. This can be done every one or two strips.
Fig. 11a
Fig. 9
Fig. 10
Fig. 11b
11. To apply the last 3-4 strips, position cut-off pieces of lagging from Step 10 in the unlagged portion of the pulley.
Manipulate the pieces to determine trim requirements for the last few strips. Trim the pieces in the gutters to find the
proper fit. Use the pieces as templates to trim the last few strips of lagging. Note: Final strips should not consist of
less than three rows.
Fig. 12
12. Follow Steps 6 through 10 to install the last 3-4 strips. The final piece of
lagging (largest of final pieces) should drop into position. Check the fit of the
last piece prior to applying the second coat of adhesive.
Fig. 13
13. Fill any gaps between the lagging strips with rubber sealer. Also use the
buffing wheel on trimmed edge of lagging and apply final coat of adhesive
to seal the edge and joint area between lagging strips.
8
Note: Allow minimum of 24 hours of curing time before putting newly
lagged pulley into use.
Section 5 – Pre-Operation Checklist and Testing
5.1 Pre-Op Checklist
• Be sure that all installation materials and tools have been removed from the belt and the conveyor area.
5.2 Test Run the Conveyor
• Run the conveyor for at least 15 minutes and inspect the lagging performance.
NOTE: Observing the pulley lagging when it is running and performing properly will help to detect problems.
9
Section 6 – Maintenance
Flexco® lagging is designed to operate with minimum maintenance. However, to maintain superior performance some
service is required. This service will ensure that the lagging operates at optimal efficiency and problems can be identified
and fixed before the lagging stops working.
All safety procedures for inspection of equipment (stationary or operating) must be observed. Flex-Lag® Pulley Lagging
operates on all pulleys in the conveyor and is in direct contact with the moving belt. Only visual observations can be made
while the belt is running. Service tasks can be done only with the conveyor stopped and by observing the correct lockout/
tagout procedures.
6.1 New Installation Inspection
After the new lagging has run for a few days a visual inspection should be made to ensure the lagging is performing
properly.
6.2 Routine Visual Inspection (every 6-8 weeks)
A visual inspection of the lagging and belt can determine:
• If there is damage to the lagging.
• If fugitive material is built up on the lagging.
• If there is damage to the belt.
If any of the above conditions exist, a determination should be made on when the conveyor can be stopped for additional
maintenance.
6.3 Routine Physical Inspection (every 3-4 months)
When the conveyor is not in operation and properly locked and tagged out, conduct a physical inspection of the lagging
to perform the following tasks:
• Clean material buildup off of the lagging.
• Closely inspect the lagging for wear and any damage.
• Ensure full lagging to belt contact.
• Inspect the belt for damage.
• Replace any worn or damaged components.
• When maintenance tasks are completed, test run the conveyor to ensure the lagging is performing properly.
10
Section 6 – Maintenance (cont.)
6.4 Maintenance Log
Conveyor Name/No.
Date:
Work done by:
Service Quote #
Work done by:
Service Quote #
Work done by:
Service Quote #
Work done by:
Service Quote #
Work done by:
Service Quote #
Work done by:
Service Quote #
Work done by:
Service Quote #
Activity:
Date:
Activity:
Date:
Activity:
Date:
Activity:
Date:
Activity:
Date:
Activity:
Date:
Activity:
11
Section 6 – Maintenance (cont.)
6.6 Lagging Maintenance Checklist
Site:
Inspected by:
Date:
Lagging:
Beltline Information:
Beltline Number:
Belt Width:
18"
(450mm)
Belt Condition:
24"
(600mm)
30"
(750mm)
36"
(900mm)
Head Pulley Diameter (Belt & Lagging):
Belt Splice
42"
(1050mm)
48"
(1200mm)
Belt Speed:
Condition of Splice
54"
(1350mm)
fpm
Number of splices
60"
1500mm)
72"
(1800mm)
Belt Thickness:
Skived
Unskived
Material conveyed
Days per week run
Hours per day run
Lagging Life:
Date installed:
Date inspected:
Estimated life:
Lagging Thickness:
Lagging:
Weld-on
Condition of lagging:
Ceramic
Good
Lagging's Overall Performance:
Bad
Other
Other
( Rate the following 1 - 5, 1 = very poor - 5 = very good )
Appearance:
Comments:
Location:
Comments:
Maintenance:
Comments:
Performance:
Comments:
Other Comments:
12
Rubber
None
Section 7 – Troubleshooting
Problem
Possible Cause
Possible Solutions
Change to ceramic lagging
Belt Tension
Uneven wear in rubber
Short Transition
lagging
Delaminating
Increase distance to full trough idler
Wrong Lagging for Application
Increase thickness or change to ceramic lagging
Glue too wet or dry when applied
Refer to instructions on p. 5-8 for proper installation instructions
Pulley surface not prepped correctly
Refer to instructions on p. 5-8 for proper installation instructions
For additional troubleshooting questions, please contact Customer Service or your territory manager.
Section 8 – Specifications and CAD Drawings
8.1 Specifications
Flex-Lag® Rubber
Criteria
Total Thickness*
Belt Width*
Minimum Pulley Diameter
Dry Performance
Wet Performance
Wear Life
Ease of Installation
Flex-Lag® Ceramic
Flex-Lag® Weld-On™
Medium
Ceramic
Full Ceramic
Rubber
Diamond
Full Ceramic
Light Duty
Plain
Diamond
Diamond
Ceramic
1/4"
(6 mm)
3/8" – 1"
(10 – 25 mm)
3/8" – 1"
(10 – 25 mm)
1/2"
(12.7 mm)
5/8"
(15 mm)
1/2"
(12.7 mm)
9/16"
(14 mm)
5/8"
(15 mm)
Any Width
Any Width
Any Width
Any Width
18" – 84"
(450 – 2100 mm)
18" – 84"
(450 – 2100 mm)
18" – 72"
(450 – 1800 mm)
18" – 72"
(450 – 1800 mm)
12" (300mm)
12” (300mm)
12” (300mm)
12” (300mm)
12” (300mm)
12” (300mm)
16" (400mm)
16” (400mm)
Very Good
Excellent
Excellent
Excellent
Excellent
Excellent
Excellent
Excellent
Average
Average
Good
Very Good
Excellent
Excellent
Good
Excellent
Good
Very Good
Very Good
Excellent
Excellent
Excellent
Very Good
Excellent
Good
Good
Good
Good
Good
Good
Excellent
Excellent
Drainage Grooves
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
FRAS (Fire Resistant Anti Static)
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
A12O3
A12O3
-
A12O3
Rubber Compound
SBR
Hardness (Shore A)
68 +/-3
Ceramic Compound
-
-
-
Hardness (HRA Rockwell Scale A)
-
-
-
83
83
83
-
83
Ceramic Coverage
-
-
-
13%
39%
80%
-
74%
Operating Temperature
A12O3
5° – 185° F
(-15° – 85° C)
*Additional thicknesses and widths available as special orders. For weld-on lagging, this includes the steel backing plate.
13
WHITE NITRILE
RUBBER
BLACK NATURAL
RUBBER
DESCRIPTION
71076
71077
6NLD3.3/11
ITEM CODE
3300
6WLD3.3/11
ORDERING
NUMBER
3300
+0.25
- 0.75
THIRD ANGLE PROJECTION
REMOVE BURRS & BREAK SHARP EDGES
UNSPECIFIED SHARP EDGES & FILLETS
WITHIN 1/32 (.79mm) 125
SURFACE ROUGHNESS
ALL MACHINED SURFACES
DATE
KAC
INITIALS
LAGGING
SCALE: 1:4 SIZE: A DRAWING NO.
SHEET
71076T
GR-25821
DOC. ID
ZCW
CHECKED
BY
100
1 of 1
REV.
1995 OAK INDUSTRIAL DRIVE, N.E.
GRAND RAPIDS, MI. 49505
PHONE: (616) 459-3196
FAX: (616) 459-4976
10/10/2013
LIGHT DUTY LAGGING
+0.5
- 0.5
+0.25
6 - 0.75
DRAWN BY: KAC
DATE:10/10/2013
TITLE:
200
RELEASED
DESCRIPTION
8.2 Lagging - Light Duty Rubber
TOLERANCES - INCH (mm)
(UNLESS OTHERWISE SPECIFIED)
.XXX
.005 (0.13mm)
.XX
.015 (0.38mm)
FRACT.
1/16 (1.59mm)
Ang.
1
THIS DRAWING IN DESIGN AND DETAIL IS
THE PROPERTY OF FLEXIBLE STEEL LACING CO.
AND MAY NOT BE USED EXCEPT IN CONNECTION
WITH OUR WORK. ALL RIGHTS OF INVENTION OR
DESIGN ARE RESERVED. RETURN UPON REQUEST.
CONFIDENTIAL! NO COPYING OR REPRODUCING!
6
REV
100
ECO
9/19/2013
14
+0.5
200 - 0.5
08074
Section 8 – Specifications and CAD Drawings (cont.)
DETAIL A
SCALE 1 : 2
A
MATERIAL
"NAT" - NATURAL RUBBER
"MSHA IC190" - FRAS
6500
+ 0.5
200 - 0.5
71010
71012
71017
71021
71163
10
12
15
20
25
10NP6.5/21
12NP6.5/21
15NP6.5/21
20NP6.5/21
25NP6.5/21
ORDERING
NUMBER
ITEM
CODE
71020
71022
71015
72129
THICKNESS
10
12
15
20
10FRP6.5/21
12FRP6.5/21
15FRP6.5/21
20FRP6.5/21
ORDERING
NUMBER
FRAS RUBBER
ITEM
CODE
NATURAL RUBBER
102
17
20
24
27
WEIGHT
16
18
23
26
29
WEIGHT
6500.0
A
A
8.3 Lagging - Plain Rubber
THICKNESS
MANUFACTURE DATE
(MONTH YEAR)
+0.5
203.0
- 0.5
+0.25
THICKNESS -0.75
15
THIC
16
THICKNESS
10
12
15
20
25
A
NATURAL RUBBER
ORDERING
ITEM CODE
NUMBER
71002
10ND6.5/21
12ND6.5/21
71004
15ND6.5/21
71006
20ND6.5/21
71008
71152
25ND6.5/21
DETAIL A
SCALE 1 : 2
6500
WEIGHT
13
17
22
24
27
10
12
15
20
THICKNESS
FRAS RUBBER
ORDERING
ITEM CODE
NUMBER
71014
10FRD6.5/21
71016
12FRD6.5/21
15FRD6.5/21
71018
71019
20FRD6.5/21
MATERIAL "NAT" - NATURAL RUBBER
"MSHA IC 190" - FRAS
MANUFACTURE DATE (MONTH/YEAR)
+0.5
200 - 0.5
14.5
18
24
27
WEIGHT
+0.25
THICKNESS -0.75
8.4 Lagging - Diamond-Pattern Rubber
MATERIAL
NATURAL RUBBER
FRAS
THICKNESS
12
12
77 TYP.
6500
71155
71159
ITEM CODE
6500
12NDC6.5/21
12FRDC6.5/21
ORDERING
NUMBER
25
27
WEIGHT
TILE ITEM CODE P3673
328
328
QTY. TILES
+0.25
12 -0.75
REV
100
ECO
DESCRIPTION
+0.25
12 - 0.75
UPDATED TITLE BLOCK AND BORDER
17
DOC. ID
XX-XX
DRAWING
199
GR
PH
FAX
SCALE: 1:5
SIZE: B
DIAMOND LAGGIN
X
TITLE:
TOLERANCES - INCH (mm)
.XXX
.005 (0.13mm)
.XX
.015 (0.38mm)
FRACT.
1/16 (1.59mm)
Ang.
1
DRAWN BY: KAC
UNSPECIFIED SHARP EDGES & FILLETS DATE:01/16/2014
WITHIN 1/32 (.79mm)
+0.5
200 - 0.5
8.5 Lagging - Diamond Ceramic
+0.5
200 - 0.5
08074
18
8.0
203
62216
DETAIL A
SCALE 1 : 2
A
CERAMIC TILE LENGTH - DIM 'A'
CLMN
CLMN
CLMN
CLMN
CLMN
CLMN
CLMN
CLMN
CLMN
CLMN
CLMN
102
102
-
08074
-
8.0
203
REV
ECO
MATERIAL
"MSHA IC190" - FRAS RUBBER
MONTH MANUFACTURED
YEAR MANUFACTURED
CERAMIC LENGTH - DIM 'A'
ADDED 61319 & A2989 TO DRAWING
REVISED ORDERING NUMBERS
DESCRIPTION
NOTES:
DIMENSIONS IN BRACKETS INCHES
8.0
203
KAC
KAC
0.59
10/15/2013
10/15/2013
DATE
INITIALS
+0.01
0.59 - 0.03
+0.25
15 - 0.75
8.01
203.5
8.0
203
ZCW
ZCW
CHECKED
BY
8.6 Lagging - Medium Ceramic, Dimpled Tiles, Natural and FRAS
DETAIL A
SCALE 1 : 2
8.0
203
A
CLMN
CLMN
CLMN
CLMN
CLMN
CLMN
CLMN
CLMN
CLMN
CLMN
8.01
203.5
REV
-
ECO
-
See 39% LAGGING
DESCRIPTION
NOTES:
DIMENSIONS IN BRACKETS INCHES
MATERIAL
"MSHA IC190" - FRAS RUBBER
MONTH MANUFACTURE
YEAR MANUFACTURE
CERAMIC LENGTH - DIM 'A'
8.0
203
-
DATE
+0.01
0.59 - 0.03
+0.25
15 - 0.75
-
INITIALS
-
CHECKED
BY
8.7 Lagging - Medium Ceramic, Smooth Tiles, Natural and FRAS
19
C
"MSHA IC190" - FRAS
MANUFACTURE DATE
(MONTH YEAR)
=
CERAMIC TILE
P2924
DETAIL C
SCALE 1 : 2
+20
DIM 'A' 0
A
A
7.5
+0.25
12 - 0.75
=
71111
71112
71113
71114
71115
71116
71039
71126
71040
71127
71117
71041
71042
71043
71037
71044
71045
71046
71047
71048
71049
71050
71000
ITEM CODE
ORDERING
NUMBER
CLN460/18.4-12
CLN600/24-12
CLN760/30.4-12
CLN800/32-12
CLN900/36-12
CLN1060/42.4-12
CLN1200/48-12
CLN1360/54.4-12
CLN1400/56-12
CLN1520/60.8-12
CLN1600/64-12
CLN1700/68-12
CLN1800/72-12
CLN1900/76-12
CLN2000/80-12
CLN2100/84-12
CLN2200/88-12
CLN2300/92-12
CLN2400/96-12
CLN2500/100-12
CLN2600/104-12
CLN2800/112-12
CLN3000/120-12
B
CERAMIC
OVERALL
SPAN DIM 'A' LENGTH DIM 'B'
460
860
600
1000
760
1160
800
1200
900
1300
1060
1500
1200
1600
1360
1800
1400
1900
1520
2000
1600
2100
1700
2200
1800
2300
1900
2400
2000
2500
2100
2600
2200
2700
2300
2800
2400
2900
2500
3000
2600
3000
2800
3300
3000
3300
203 ±0.5
DIM 'A'
DIM 'B'
7.5
+0.25
12 - 0.75
A
A
71118
71119
71120
71121
71122
71123
71005
A1636
71007
71009
71124
71078
71079
71080
71081
71082
71083
71084
71085
71086
71087
71088
71089
ITEM CODE
ORDERING
NUMBER
CLFR460/18.4-12
CLFR600/24-12
CLFR760/30.4-12
CLFR800/32-12
CLFR900/36-12
CLFR1060/42.4-12
CLFR1200/48-12
CLFR1360/54.4-12
CLFR1400/56-12
CLFR1520/60.8-12
CLFR1600/64-12
CLFR1700/68-12
CLFR1800/72-12
CLFR1900/76-12
CLFR2000/80-12
CLFR2100/84-12
CLFR2200/88-12
CLFR2300/92-12
CLFR2400/96-12
CLFR2500/100-12
CLFR2600/104-12
CLFR2800/112-12
CLFR3000/120-12
CERAMIC SPAN
DIM 'A'
460
600
760
800
900
1060
1200
1360
1400
1520
1600
1700
1800
1900
2000
2100
2200
2300
2400
2500
2600
2800
3000
OVERALL
LENGTH DIM 'B'
860
1000
1160
1200
1300
1500
1600
1800
1900
2000
2100
2200
2300
2400
2500
2600
2700
2800
2900
3000
3000
3300
3300
REFERENCE TABLE FOR FULL CERAMIC FRAS COMPOUND LAGGING
SECTION A-A
SCALE 1 : 2
REFERENCE TABLE FOR FULL CERAMIC NATURAL RUBBER
LAGGING
DETAIL B TYP.
SCALE 1 : 1
11
51
51
20
51
DIM 'B' 10
203
-
-
11
UNSPECIFIED SHARP EDGES & FILLETS
WITHIN 1 mm (.04 in) 125
SURFACE ROUGHNESS
ALL OVER
FULL
SCALE: 1:33.3
SIZE:
DRAWN BY: MJC
DATE:10/11/200
TITLE:
DETAIL B
SCALE 1 : 1
7
ADDED SECOND PAGE WITH SMOOTH TI
TOLERANCES - mm (INCH)
X.XX
.1 (0.004 in)
X.X
.5 (0.020 in)
X
1 (0.04 in)
Ang.
1
DESCRIPTION
UPDATE PRINT
UPDATED ORDERING NUMBERS
45°
102
REV
101
---
ECO
8.8 Lagging - Full Ceramic, Dimpled Tiles, Natural and FRAS
08074
C
"MSHA IC190" - FRAS
MANUFACTURE DATE
(MONTH YEAR)
=
DETAIL C
SCALE 1 : 2
A
A
=
79383
79384
79385
79386
79387
79388
79389
79390
79391
79392
79393
79394
79395
79396
79397
79398
79399
79400
79401
79402
79403
79404
79405
ORDERING
NUMBER
CLN460/18.4-12S
CLN600/24-12S
CLN760/30.4-12S
CLN800/32-12S
CLN900/36-12S
CLN1060/42.4-12S
CLN1200/48-12S
CLN1360/54.4-12S
CLN1400/56-12S
CLN1520/60.8-12S
CLN1600/64-12S
CLN1700/68-12S
CLN1800/72-12S
CLN1900/76-12S
CLN2000/80-12S
CLN2100/84-12S
CLN2200/88-12S
CLN2300/92-12S
CLN2400/96-12S
CLN2500/100-12S
CLN2600/104-12S
CLN2800/112-12S
CLN3000/120-12S
CERAMIC
SPAN DIM 'A'
460
600
760
800
900
1060
1200
1360
1400
1520
1600
1700
1800
1900
2000
2100
2200
2300
2400
2500
2600
2800
3000
B
7.5
SECTION A-A
SCALE 1 : 2
OVERALL
LENGTH DIM 'B'
860
1000
1160
1200
1300
1500
1600
1800
1900
2000
2100
2200
2300
2400
2500
2600
2700
2800
2900
3000
3000
3300
3300
REFERENCE TABLE FOR FULL CERAMIC NATURAL RUBBER
LAGGING
CERAMIC TILE
P2924
ITEM CODE
+20
DIM 'A' 0
+0.25
12 - 0.75
51
51
51
DIM 'B' 10
11
203 ±0.5
79406
79407
79408
79409
79410
79411
79412
79413
79414
79415
79416
79417
79418
79419
79420
79421
79422
79423
79424
79425
79426
79427
79428
ITEM CODE
ORDERING
NUMBER
CLFR460/18.4-12S
CLFR600/24-12S
CLFR760/30.4-12S
CLFR800/32-12S
CLFR900/36-12S
CLFR1060/42.4-12S
CLFR1200/48-12S
CLFR1360/54.4-12S
CLFR1400/56-12S
CLFR1520/60.8-12S
CLFR1600/64-12S
CLFR1700/68-12S
CLFR1800/72-12S
CLFR1900/76-12S
CLFR2000/80-12S
CLFR2100/84-12S
CLFR2200/88-12S
CLFR2300/92-12S
CLFR2400/96-12S
CLFR2500/100-12S
CLFR2600/104-12S
CLFR2800/112-12S
CLFR3000/120-12S
CERAMIC
SPAN DIM 'A'
460
600
760
800
900
1060
1200
1360
1400
1520
1600
1700
1800
1900
2000
2100
2200
2300
2400
2500
2600
2800
3000
OVERALL
LENGTH DIM 'B'
860
1000
1160
1200
1300
1500
1600
1800
1900
2000
2100
2200
2300
2400
2500
2600
2700
2800
2900
3000
3000
3300
3300
REFERENCE TABLE FOR FULL CERAMIC FRAS COMPOUND
LAGGING
DETAIL B TYP.
SCALE 1 : 1
7.5
+0.25
12 - 0.75
8.9 Lagging - Full Ceramic, Smooth Tiles, Natural and FRAS
21
Section 9 – Lagging Adhesives and Toolbox
Flex-Lag® Adhesive/Activator/Primer
ORDERING NUMBER DESCRIPTION ITEM CODE
WEIGHT
VOLUME
FL-ADH-0.8
Adhesive
75017
1.6 lb.
0.7 Kg
FL-ACT
Activator
70186
0.1 lb.
40 g
Primer
70189
1.6 lb.
0.7 Kg
FL-PR-0.75
27.1 oz
0.8L
-
-
25.4 oz
0.75L
Each Flex-Lag Adhesive is mixed with one Flex-Lag Activator.
Refer to the usage chart below to calculate the number of cans
required for your pulley. For sizes not included in the chart
please contact Flexco® Customer Service for assistance.
®
FLEX-LAG® ADHESIVE 0.8L / ACTIVATOR 40g (1:1 mix ratio)
Face Width
Pulley Diameter
In.
8
12
16
20
24
28
32
36
40
44
48
52
56
60
10
14
18
22
26
30
34
38
42
46
50
54
58
62
66
70
74
78
82
86
90
mm
254
356
457
559
660
762
864
965
1067
1168
1270
1372
1473
1575
1676
1778
1880
1981
2083
2184
2286
203
305
406
508
610
711
813
914
1016
1118
1219
1321
1422
1524
1
1
1
1
1
1
2
2
2
2
2
2
2
2
1
1
1
1
2
2
2
2
2
2
3
3
3
3
1
1
1
2
2
2
2
3
3
3
3
3
4
4
1
1
2
2
2
2
3
3
3
4
4
4
4
5
1
1
2
2
2
3
3
3
4
4
4
5
5
5
1
2
2
2
3
3
4
4
4
5
5
5
6
6
1
2
2
3
3
3
4
4
5
5
6
6
6
7
1
2
2
3
3
4
4
5
5
6
6
7
7
8
2
2
3
3
4
4
5
5
6
6
7
7
8
8
2
2
3
3
4
5
5
6
6
7
7
8
9
9
2
2
3
4
4
5
6
6
7
7
8
9
9
10
2
3
3
4
5
5
6
7
7
8
9
9
10
11
2
3
3
4
5
6
6
7
8
9
9
10
11
11
2
3
4
4
5
6
7
8
8
9
10
11
11
12
2
3
4
5
5
6
7
8
9
10
10
11
12
13
2
3
4
5
6
7
8
8
9
10
11
12
13
14
2
3
4
5
6
7
8
9
10
11
12
13
14
14
2
3
4
5
6
7
8
9
10
11
12
13
14
15
3
4
5
6
7
8
9
10
11
12
13
14
15
16
3
4
5
6
7
8
9
10
11
12
13
15
16
17
3
4
5
6
7
8
10
11
12
13
14
15
16
17
FLEX-LAG® PRIMER .75L
Face Width
Pulley Diameter
In.
8
12
16
20
24
28
32
36
40
44
48
52
56
60
10
14
18
22
26
30
34
38
42
46
50
54
58
62
66
70
74
78
82
86
90
mm
254
356
457
559
660
762
864
965
1067
1168
1270
1372
1473
1575
1676
1778
1880
1981
2083
2184
2286
203
305
406
508
610
711
813
914
1016
1118
1219
1321
1422
1524
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
2
2
2
1
1
1
1
1
1
1
1
1
1
2
2
2
2
1
1
1
1
1
1
1
1
1
2
2
2
2
2
1
1
1
1
1
1
1
1
1
2
2
2
2
2
1
1
1
1
1
1
1
1
2
2
2
2
2
2
1
1
1
1
1
1
1
1
2
2
2
2
2
2
1
1
1
1
1
1
1
2
2
2
2
2
2
2
Flex-Lag® Toolbox
ORDERING NUMBER
DESCRIPTION
ITEM CODE
WT. (LBS)
LAGGING-TB
with Power Tools
79080
32.0
LAGGING-TB2
without Power Tools
79099
20.0
Both Include:
• 25-ft measuring tape
• BCP location tool • Chalk line
• Paint brushes (3)
• Lagging stitchers (3) • White paint marker LAGGING-TB Also Includes:
• Air hammer kit
• 24-grit flap disc
• Rubber buffing disc 22
• Grinder
• Metal grinding disc
• Oscillating tool and accessories
• HD knife and replacement blades
• Bench brush
• Deadblow hammer
Section 10 – Other Flexco Conveyor Products
Flexco® provides many conveyor products that help your conveyors to run more efficiently and safely.
These components solve typical conveyor problems and improve productivity.
Here is a quick overview on just a few of them:
MSP Precleaner
• Patented ConShear™ blade renews its cleaning edge as it wears
• Visual Tension Check™ for optimal blade tensioning and
simple retensioning
• Quick and easy one-pin blade replacement Material Path
Option™ for optimal cleaning and reduced maintenance
EZS2 Secondary Cleaner
• Long-wearing tungsten carbide blades for superior
cleaning efficiency
• Patented FormFlex™ cushions independently tension each
blade to the belt for consistent, constant cleaning power
• Easy to install, simple to service
• Works with Flexco mechanical belt splices
Flexco® Specialty Belt Cleaners
• “Limited space” cleaners for tight conveyor applications
• High Temp cleaners for severe, high heat applications
• A rubber-fingered cleaner for chevron and raised-rib belts
• Multiple cleaner styles in stainless steel for corrosive applications
DRX™ Impact Beds
• Exclusive Velocity Reduction Technology™ to better
protect the belt
• Slide-Out Service™ gives direct access to all impact bars
for change-out
• Impact bar supports for longer bar life
• 4 models to custom fit to the application
PT Max™ Belt Trainer
• Patented “pivot & tilt” design for superior training action
• Dual sensor rollers on each side to minimize belt damage
• Pivot point guaranteed not to seize or freeze up
• Available for topside and return side belts
Belt Plows
• A belt cleaner for the tail pulley
• Exclusive blade design quickly spirals debris off the belt
• Economical and easy to service
• Available in vee or diagonal models
25
The Flexco Vision
To become the leader in maximising
belt conveyor productivity for our customers worldwide
through superior service and innovation.
1995 Oak Industrial Drive NE • Grand Rapids, MI 49505 U.S.A.
Tel: (616)-459-3196 • Fax: (616)-459-4976 • E-mail: info@flexco.com • Web: www.flexco.com
Visit www.flexco.com for other Flexco locations and products.
©2014 Flexible Steel Lacing Company. 11/14. X2975

Flex-Lag® Cold Bond Pulley Lagging

Transcription

Similar documents

Lagging for Pulleys

RSA Winter Conference 2014 Niall Crosbie, prof. Bill O`Gorman

lnstallation lnstructions for 05

Go Kart Torque Converter

Bearings Power Transmission Equipment - Anderson

SUPERCHARGER PULLEY REPLACEMENT PROCEDURE

case study shleppers

See TC102 (print version)

Steeda Underdrive Pulleys (Late 01-04 GT)