Tele Radio Tiger ADVANCED INSTALLATION INSTRUCTIONS

Transcription

Tele Radio Tiger
ADVANCED INSTALLATION
INSTRUCTIONS
XAPP LIFT RELAY SETTINGS
ENGLISH (ORIGINAL)
TG-R1-1-0000, TG-R1-11-0000, TG-R1-6-0000, TG-T00003-05
ARTICLE CODE: TG-T3-4-0000, TG-T3-5-0000, TG-T4-11-0000,
TG-T4-5-0000, TG-R1-1-0000, TG-R1-11-0000, TG-R1-6-0000
IM-TG-RX02-A01-EN
CONTENTS
The joystick transmitter The joystick menu
The menu map and how to navigate
5
6
6
Select how to control the main and aux loads Select main and aux load on the joystick transmitter
Quick guide for the front switch
Operating mode
Buzzer output
Operating mode 1
Operating mode 2
Operating mode 3
Operating mode 4
7
8
9
10
10
11
12
13
13
Enable more than one receiver
Select what receiver(s) to be active during a session Select what receiver(s) to be selected by default
Enable Main load and/or Aux load
Activate Main load and/or Aux load at start up
Relay settings
Momentary or toggling/ latching relay functionality
Interlocking relay functionality
Blocking
Prioritization
14
14
14
15
15
16
16
17
17
17
Thank you for puchasing a Tele Radio product
RX1-A, RX2-A, RX3-A + TX2-A
READ ALL INSTRUCTIONS CAREFULLY BEFORE MOUNTING, INSTALLING AND
CONFIGURATING THE PRODUCT.
These instructions are published by Tele radio AB without any guarantee. These
instructions are solely directed towards qualified installers. The information shall not be
handed to end users. The instructions may be removed or revised by Tele radio AB at
any time and without any further notice. Corrections and additions will be added to the
updated versions of the instructions.
The instructions that contain information on the installation and configuration of the
remote radio control unit on the machine are not intended to be passed on to the end
user. Only such information may be passed on to the end user, that is needed to operate
the machine correctly by radio remote control.
Tele Radio AB products are covered by a guarantee against material, construction or
manufacturing faults. During the guarantee period, Tele Radio AB may replace the product
or faulty parts with new. Work under guarantee must be carried out by Tele Radio AB
or by an authorized service centre specified by Tele Radio AB. Make sure that repairs and
maintenance are only carried out by qualified personnel. Use only spare parts from Tele
Radio AB. Contact your Tele Radio representative if you want to make a complaint about
a product or require other service.
“Declaration of Conformity” can be downloaded from our website.
©Tele Radio AB, 2010
TELE RADIO AB
Datavägen 21, SE-436 32 Askim. Sweden
Tel: +46 (0)31-748 54 60
Fax: +46 (0)31-68 54 64
www.tele-radio.com.
info@tele-radio.com
4
THE JOYSTICK TRANSMITTER
FRONT SIDE
1. Left joystick
2. Right joystick
3. Front switch
LEFT SIDE
1
4. Function switch
5. Stop button
6. Red/ green LED 1
2
7. Display
8. Red/ green LED 2
RIGHT SIDE
3
4
5
1. Side button 1
2. Side button 2 (Safe button)
3. Side button 3 (Start button)
4. Side button 4 (Start & Safe button)
5. Stop button
5
THE JOYSTICK MENU
JOYSTICK MENU MAP
SETTINGS
>Channel
1: 433.075MHz...
69: 434.775MHz...
>Show receivers
E.g. 1: 92041
E.g. 2: 90088...
>Logout
E.g. 1: 92041
E.g. 2: 90088...
>Auto shutdown
6 min
2 min
Off
12 min
>Register
No
Yes
>Erase
E.g. 1: 92041
E.g. 2: 90088...
>Replace
No
Yes
>Show SW version
No
Yes
>Test Mode
No
Yes
HOW TO NAVIGATE IN THE THE JOYSTICK MENU
•
•
•
•
6
TO MOVE UP AND DOWN: Move the left joystick up or down
TO SELECT: Press side button 4
TO GO BACK: Move the left joystick to the left
TO EXIT: Press side button 3. The joystick will turn off.
SELECT HOW TO CONTROL THE MAIN AND AUX LOADS
The lower switch, the Function switch,
is used for controlling the Main and/or
Aux loads. What functionality you will
get, depends on the position of the
upper switch, the Front switch (see
next page for more information).
See the Operating mode section for
information about Operating modes.
1+2
1
2
1
By switching the Function switch, you
can control:
• Main 1, Main 2 or both Main loads
at the same time.
• Aux 1, Aux 2 or both Aux at the
same time.
To control only Main 1 and/ or Aux 1:
press the switch to the left.
control Main 1 and/or Aux 1
1+2
To control both Main 1+2 and/ or
Aux 1+2: press the switch to the mid
position.
control Main 1+2 and/or
Aux 1+2 at the same time
2
To control only Main 2 and/ or Aux 2:
press the switch to the right.
control Main 2 and/or Aux 2
7
SELECT MAIN AND AUX LOAD ON THE JOYSTICK TRANSMITTER
Main
Aux
The upper switch, the Front switch, is a
toggling switch, i.e. pressing the switch
once in a direction, will turn the
functionality on. Pressing the switch
twice in the same direction, will turn
the functionality off.
This switch is used for turning on and
off the Main and/or Aux. If Main is on,
the Main LED lights. If Aux is on, the
Aux LED lights.
Press to the left will activate Main.
Press to the right will activate Aux.
To turn Main on, press the switch to
the left. The main LED lights up.
To turn Main off, press the switch to
the left again. The main LED goes out.
MAIN ON = 1 x
MAIN OFF = 2 x
AUX ON = 1 x
AUX OFF = 2 x
8
To turn Aux on, press the switch to
the right. The Aux LED lights up.
To turn Aux off, press the switch to
the right again. The Aux LED goes out.
To turn on both Main and Aux, press
the switch once to the left and once
to the right. Both the Main LED and the
Aux LED light up.
To turn off both Main and Aux, press
the switch once to the right and once
to the left. Both the Main LED and the
Aux LED go out.
QUICK GUIDE FOR THE FRONT SWITCH
Main and Aux LEDs
MAIN LED
ON
OFF
ON
OFF
AUX LED
OFF
ON
ON
OFF
RESULT
MAIN ON
AUX ON
MAIN + AUX ON
MAIN + AUX OFF
Aux LED
For Operating Mode 1-3. AUX selected + extra relay activated:
AUX SELECTED
1
2
1+2
AUX LED LIT
yes
yes
yes
EXTRA RELAY ACTIVATED
27
28
27+28
Main LED
ON THE 2 STEP JOYSTICK
For Operating Mode 1 or 2. MAIN selected + extra relay activated:
MAIN SELECTED
1
2
1+2
MAIN LED LIT
yes
yes
yes
10
11
10+11
ON THE 4 STEP JOYSTICK
For Operating Mode 3. MAIN selected + extra relay activated:
MAIN SELECTED
1
2
1+2
MAIN LED LIT
yes
yes
yes
11
14
11+14
9
SELECT OPERATING MODE FOR THE RECEIVER
You can switch Operating Mode in the receiver menu. Operating Mode 1 is default.
Operating Mode 4 is for customized settings. Contact your representative for more
information about Operating Mode 4.
1.
2.
3.
4.
Enter the receiver menu [SYSTEM SETUP].
Press the receiver joystick one step to the right.
Enter the submenu [xApp SETUP] and press the receiver joystick [Operating Mode].
Press the receiver joystick upwards to scroll through the list. Select Operating Mode
1 or 2.
Learn more about Operating Modes on the next pages.
ACTIVATE THE BUZZER
The buzzer button will activate relay 12 in Operating Mode 1-3. The buzzer output on
the receiver main bord can only be activated in Operating Mode 4.
10
OPERATING MODE 1
JOYSTICK- 2 STEPS
MAIN LED
25
11
10
MAIN
9
8
6 4
5 6
7
9
26
AUX LED
28
27
3
AUX
1
22 20
27 28
2
10 11
3
13
19
17
21 22
18
19
12
28
11
27
10
MAIN= toggle MAIN on/ off AUX= toggle AUX on/ off (LED MAIN= lit when MAIN is on)
(LED AUX = lit when AUX is on)
NOTE! whitemarked relays added= only for joystick transmitters with X-direction on the
right joystick
ABOUT OPERATING MODE 1:
•
•
•
•
•
2 steps joystick transmitter
Common high-speed
2 MAIN lifts can be selected
2 AUX can be selected
AUX can activate help lift in UP and DOWN directions
JD
1
2
3
4
5
6
7
8
9
10
11
12
13
17
18
19
2 STEPS
3 motors
1
2
3
4
5
6
7
8
9
10
11
12
13
17
18
19
2 STEPS
4 motors
1
2
3
4
5
6
7
8
9
10
11
12
13
17
18
19
14
15
16
20
20
21
21
22
22
23
24
25
26
27
28
25
26
27
28
25
26
27
28
11
OPERATING MODE 2
JOYSTICK- 2 STEPS
LED MAIN
25
11
10
MAIN
17
16
6 5
26
LED AUX
7 8
28
27
AUX
2
1
21 20
3
4
27 28
10 11
14
15
13
19
18
22 23
9
24
12
28
11
27
10
MAIN= toggle MAIN on/ off AUX= toggle AUX on/ off (LED MAIN= lit when MAIN is on)
(LED AUX= lit when AUX is on)
right joystick
•
•
•
•
•
12
Separate high-speed
AUX can activate help lift in UP and DOWN directions
JD
1
2
3
4
5
6
7
8
9
10
11
12
13
17
18
19
2 STEPS
3 motors
1
2
3
4
5
6
7
8
9
10
11
12
13
17
18
19
2 STEPS
4 motors
1
2
3
4
5
6
7
8
9
10
11
12
13
17
18
19
14
15
16
20
20
21
21
22
22
23
23
24
25
26
27
28
24
25
26
27
28
24
25
26
27
28
OPERATING MODE 3
JOYSTICK- 4 STEPS
LED MAIN
25
19 18 17 15
10
9
8
7
LED AUX
14
11
MAIN
16 17 18 19
6
8
9
10
26
28
27
AUX
24 23 22 20
27 28
11 14
MAIN= toggle MAIN on/ off AUX= toggle AUX on/ off 13
21 22 23 24
2
3
4
5
28
14
27
11
5
4
3
1
12
(LED MAIN= lit when MAIN is on)
(LED AUX= lit when AUX is on)
right joystick
•
•
•
•
Common high-speed
JD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
4 STEPS
3 motors
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
4 STEPS
4 motors
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
20
21
21
22
22
23
23
24
24
25
26
27
28
25
26
27
28
25
26
27
28
OPERATING MODE 4
Operating mode 4 allows customized settings with remapped outputs and inputs.
Operating mode 4 can not be selected from the receiver, but has to be done by a Tele
Radio representative. Contact your representative if you want to know more about
customizations.
13
ENABLE MORE THAN ONE RECEIVER
Default= 1 receiver (single). The period of time between starting and stopping of the
transmitter is defined as a session.You can learn more about sessions in the Basic
installation instruction. The joystick transmitter can control 1-8 receivers during the same
session. Each receiver can have 1-2 main loads and/ or 1-2 aux loads enabled. If you have
set the system to a single receiver, you can only control 1 receiver per session. In such a
case, you can register more than one receiver in your joystick transmitter, but you can
not control more than one receiver at a time or during the same session.
1.
2.
3.
4.
Start up the transmitter in menu mode. See ”Start up in menu mode”.
Scroll to Receiver limit.
Select by pressing side button 4.
Select between:
•Single receiver
•Unlimited
5. Select by pressing side button 4.
SELECT WHAT RECEIVER(S) TO BE ACTIVE DURING A SESSION
You can learn more about sessions in the Basic installation instruction. If more than one
receiver is registered in the transmitter, you need to know the position of the receiver(s)
that you want to select in the transmitter.
1. Look up the receiver ID code on the label on the receiver.
2. Check what position in the transmitter that the receiver(s) is placed on in the
receiver menu.
3. Pull out the stop button.
4. Select one or more receivers by pressing the left joystick upwards. The selected
receiver will be pointed at by an arrow.
5. Press the side buttons 3+4 to start the session.
6. The selected receiver(s) may now be synchronously operated.
SELECT WHAT RECEIVER(S) TO BE SELECTED BY DEFAULT
It´s possible to preset what receiver(s) to control at start up. To set one or more
receivers as default at start up:
1. Contact your representative.
14
ENABLE MAIN LOAD AND/OR AUX LOAD
For every registered receiver, you can select what main loads or aux loads that you want
to enable controlling of, i.e. this is where you enable 1 or 2 main loads + 1 or 2 aux loads.
Default= 1 and/or 2 on.
1.
2.
3.
4.
Scroll to Main.
Select between:
•1 or 2 on
•1 and/or 2 on
6. Scroll to Aux.
8. Select between:
•1 or 2 on
•1 and/or 2 on
ACTIVATE MAIN LOAD AND/OR AUX LOAD AT START UP
When you have enabled main load and/or aux load, you may want to select what main
loads and/or aux loads that you want to activate every time that you start the joystick
(until the setting is changed). The LED(s) will light accordingly. Default= All off. If set on
[ All off], you have to use the Front switch to select when you start up.
1.
2.
3.
4.
Scroll to Load at start.
Select between:
•Aux
•Main
•Main and aux
•All off
15
RELAY SETTINGS
MOMENTARY OR TOGGLING/ LATCHING RELAY
FUNCTIONALITY
All relays have a momentary functionality as default.
MOMENTARY
The relay is only activated when a side button or a joystick step is being pressed. When
the button or joystick step is released, the relay is deactivated.
TOGGLING/ LATCHING
The relay will stay activated until the side button or joystick step is being pressed again.
CHANGE THE SETTINGS
You can switch between momentary and toggling/ latching relay functionality in the
receiver menu. The menu displays a list of all relays, but only relays 13, 25 + 26 can be
assigned a latching funcionality.
Latching= [L]
16
INTERLOCKING RELAY FUNCTIONALITY
BLOCKING
The standard relays and the additional relays that are being controlled by different
joystick steps on the joystick transmitter are interlocked. This means that UP- DOWN,
LEFT-RIGHT or BACK-FORTH can not activate at the same time. The relays involved will
be blocked if you try to activate them at the same time.
PRIORITIZATION
You can prioritize between certain relays in the receiver menu.
E.g. for Operating mode 2: 01 can be set to ‘A’ for no priority. If set to ‘B’, relay 2 gets
priority over relay 1 and relay 4 gets priority over relay 3. The table shows what
prioritizations that can be made in the receiver menu:
For Operating mode 1:
01A= No priority between 3 and 1. No priority between 3 and 2.
01B= Relay 3 has priority over 1. Relay 3 has priority over 2.
02A=No priority between 6 and 4. No priority between 6 and 5.
For Operating mode 2:
01A= No priority between 2 and 1. No priority between 4 and 3.
17
TELE RADIO AB
Sweden, Main office
Tel. +46 (0)31-748 54 60
e-mail: info@tele-radio.com
www.tele-radio.com
TELE RADIO SVERIGE
Sweden
Tel. +46 (0)31-724 98 00
e-mail: sverige@tele-radio.com
TELE RADIO GmbH
Germany
Tel. +49 (0)94 51-944 8 550
e-mail: deutschland@tele-radio.com
TELE RADIO ASIA
China
Tel. +86-(0)592-3111168
e-mail: china@tele-radio.com
TELE RADIO TURKEY
Turkey
Tel. +90 216 574 22 94
e-mail: turkiye@tele-radio.com
TELE RADIO LTD
England
Tel. +44 (0) 1625 509125
e-mail: england@tele-radio.com
TELE RADIO LLC
North America & Latin America
Tel. +1 (305) 459 0763
e-mail: america@tele-radio.com
TELE RADIO BV
Benelux
Tel. +31-(0)70-419 41 20
e-mail: benelux@tele-radio.com
TELE RADIO AS
Norway
Tel. +47-6933 4900
e-mail: norge@tele-radio.com

Tele Radio Tiger ADVANCED INSTALLATION INSTRUCTIONS

Transcription

Similar documents

Base ASKW Announcement

AzureWave ARR5B95 Us..

Super4 RS485 Relay Module Specification

500 Series Quickstart Guide

live performance console

Mauritius - Thompsons Holidays

rsfsb user manual tm

JC1500 Single Axis Contactless Joystick

Bitron AV1407/001 (4+n) T-Line