Specification Sheets

P
Pyxis Link
IS
YX
PYX-P5-18
P
5Ghz Outdoor PTP/
PTMP AP/CPE/Bridge
IS
YX
PTP Up to 20 km
PTMP Distance: 7km
PTMP full capacity: 2km
Real Throughput 160Mbps
Key Features
• Multi mode supported AP/CPE/PTP bridge/PTMP
• Radio rate 300Mbps
• Cost Effective
• True aggregate throughput up to 160Mbps
• Advanced proprietary TDD MiMo Wireless Protocol - Less interference
• Low packet latency
• Spectrum analyser for site survey
• TDD for allocating bandwidth
• Integrated 18dBi MiMo antenna
• 29 dBm TX Radio
• Management features: Web GUI, SSH SNMP V1/2/3, Syslog server
• LED Signal indicator for antenna alignment
• IP-66 Weather Proof Housing
wireless technology specialists
Warrington Lane, Lymm,
Warrington WA13 0SW
Tel: 0161 241 0557
www.cdndistribution.co.uk
Radio SPEC
WLAN standard
Radio mode
Operating modes
Radio frequency band
Transmit power
Receive sensitivity
Channel size
Modulation schemes
Data rates
Error correction
Duplexing scheme
Antenna SPEC
Type
Gain
Polarization
Cross-pol- Isolation
Max VSWR
H-pol Beamwidth
V-pol Beamwidth
Elevation Beamwidth
IEEE 802.11 a/n, TDD
(proprietary)
MIMO 2x2
Access point, CPE, WDS
Bridge mode, PTMP BS,
PTMP CPE
4.9 - 5.9GHz
(Country dependent)
Up to 29 dBm
(Country dependent)
Varying between -95 and
-75 dBm depending on
modulation
20, 40 MHz
802.11 a/n: OFDM (64-QAM,
16-QAM, QPSK, BPSK)
802.11 n: 300, 270, 240,
180, 120, 90, 60, 30 Mbps
802.11 a: 54, 48, 36, 24,
18, 12, 9, 6 Mbps
FEC, Selective ARQ
Time division duplex
Integrated directional dualpolarized panel
18 dBi
Dual Linear
27dBi
1:8:1
16°
16°
16°
Antenna spec (PYX-P5-18)
Wired
Interface
Networking
Operating modes
WAN
NAT
Static routing
DHCP
Port forwarding
VLAN
Physical
Dimensions
Weight
Power supply
Power source
Power consumption
10/100 Base-T, RJ45
Bridge, Router
Static IP, DHCP client, PPPoE
client
Routing w/ or w/o NAT
Supported
Client, Server, Relay
Supported
Supported for management
and data
L20.5cm, W20.5cm, H4.5cm
700 g
12 - 48 V DC passive PoE
100 – 240 VAC via included
adapter
6.5 W
Environmental
Operating temperature -40°C (-22 F) ~ +65°C (+149 F)
Humidity
0 ~ 90 % (non-condensing)
Management
System configuration
System monitoring
Regulatory
Certification
User-friendly web GUI,
Command line via SSH
SNMP v1/2c/3 server, Syslogs,
system alerts via e-mail and
SNMP trap
FCC/CE/Safety/RoHS
compliance
P
Pyxis Link
IS
YX
PYX-P5-23
P
5Ghz Outdoor PTP/
PTMP AP/CPE/Bridge
IS
YX
PTP ~ 50 km
PTMP ~ 25km
PTMP full capacity: 10km
Real Throughput 160Mbps
Key Features
• Multi mode supported AP/CPE/PTP bridge/PTMP
• Radio rate 300Mbps
• Cost Effective long range PTP/PTMP
• True aggregate throughput up to 160Mbps
• Advanced proprietary TDD MiMo Wireless Protocol - Less interference
• Low packet latency
• Spectrum analyser for site survey
• TDD for allocating bandwidth
• Integrated 23dBi MiMo antenna
• 29 dBm TX Radio
• Management features: Web GUI, SSH SNMP V1/2/3, Syslog server
• LED Signal indicator for antenna alignment
• IP-67 Weather Proof Housing
wireless technology specialists
Warrington Lane, Lymm,
Warrington WA13 0SW
Tel: 0161 241 0557
www.cdndistribution.co.uk
Radio SPEC
WLAN standard
Radio mode
Operating modes
Radio frequency band
Transmit power
Receive sensitivity
Channel size
Modulation schemes
Data rates
Error correction
Duplexing scheme
Antenna SPEC
Type
Gain
Polarization
Cross-pol- Isolation
Max VSWR
H-pol Beamwidth
V-pol Beamwidth
Elevation Beamwidth
IEEE 802.11 a/n, TDD
(proprietary)
MIMO 2x2
Access point, CPE, WDS
Bridge mode, PTMP BS,
PTMP CPE
4.9 - 5.9GHz
(Country dependent)
Up to 29 dBm
(Country dependent)
Varying between -95 and
-75 dBm depending on
modulation
20, 40 MHz
802.11 a/n: OFDM (64-QAM,
16-QAM, QPSK, BPSK)
802.11 n: 300, 270, 240,
180, 120, 90, 60, 30 Mbps
802.11 a: 54, 48, 36, 24,
18, 12, 9, 6 Mbps
FEC, Selective ARQ
Time division duplex
Integrated directional dualpolarized panel
23 dBi
Dual Linear
27dBi minimum
1:5:1
6°
7°
9°
Antenna spec (PYX-P5-23)
Wired
Interface
10/100 Base-T, RJ45
Built-in Surge Protection Yes
Networking
Operating modes
WAN
NAT
Static routing
DHCP
Port forwarding
VLAN
Physical
Dimensions
Weight
Power supply
Power source
Power consumption
Bridge, Router
Static IP, DHCP client, PPPoE
client
Routing w/ or w/o NAT
Supported
Client, Server, Relay
Supported
Supported for management
and data
L33.5cm, W33.5cm, H9cm
3.3 kg
12 - 48 V DC passive PoE
100 – 240 VAC via included
adapter
6.5 W
Environmental
Operating temperature -30°C ~ +75°C
Humidity
0 ~ 90 % (non-condensing)
Management
System configuration
System monitoring
Regulatory
Certification
User-friendly web GUI,
Command line via SSH
SNMP v1/2c/3 server, Syslogs,
system alerts via e-mail and
SNMP trap
FCC/CE/Safety/RoHS
compliance
P
Pyxis Link
IS
YX
PYX-P5-23/N-PRO
P
5Ghz Outdoor PTP Bridge
IS
YX
215Mbps
Real TCP/IP Throughput
PTP up to 50+KM
60000+
PACKETS PER SECOND
Key Features
•10/100/1000 BaseT (GigaBit) Ethernet port
• Radio rate up to 300Mbps
• True aggregate throughput up to 215 Mbps (100+Mbps Full Duplex)
• Advanced proprietary TDD MiMo wireless protocol - Less interference
• High packet-per-second (PPS) rate – ideal for VOIP/CCTV backhaul applications
• Low packet latency
• Excellent spectral efficiency
• Dynamic TDD for allocating bandwidth
• Integrated 23dBi MiMo antenna (PYX-P5-23-PRO)
• 802.3af POE
• 28 dBm TX Radio
• Spectrum Analyser tool for site survey
• Management features: Web GUI, SSH SNMP V1/2/3, Syslog server
• LED screen for antenna alignment
• IP-67 Weather Proof Housing
wireless technology specialists
Warrington Lane, Lymm,
Warrington WA13 0SW
Tel: 0161 241 0557
www.cdndistribution.co.uk
Radio SPEC
Wireless Technology
Operating mode
Radio frequency band
Channel Size
Max transmit power
Modulation schemes
Receive sensitivity
Error correction
Duplexing scheme
Antenna SPEC
Type
Polarization
Gain V/H
3dB Beam-width V/H
Data Interface
Physical Interface
Protocol
Connector type
Surge protection
Proprietary TDD protocol,
5GHz 2x2 MIMO 300Mbps
Point-to-point only
5.150 - 5.915GHz
(Country dependent)
20/40 MHz
28 (+/-2) dBm
(Country dependent)
BPSK, QPSK, 16QAM, 64QAM
Varying between -94 and
-72 dBm depending on
modulation and channel size
FEC, Selective ARQ
Dynamic time division duplex
Integrated directional panel
(PYX-P5-23 PRO) or 2 N-Type
connectors (PYX-P5-N PRO)
Dual (PYX-P5-23 PRO)
23 dBi (PYX-P5-23-PRO)
8/8 degrees
(PYX-P5-23 PRO)
10/100/1000 BaseT
Ethernet IEEE 802.3
RJ45
Built-in (IEC 61000-4-2 (ESD)
and IEC 61000-4-5 (SURGE))
Link Performance
Real data throughput
215+ Mbps aggregate (100+
Mbps full-duplex)
Max packets per second 60,000+
2 ms (64 bytes packet)
Packet latency
More than 100km (62,17 mi)
Link distance**
Security
Data encryption
Hardware based AES
Physical
Dimensions (P5-23-PRO)
Dimensions (P5-N-PRO)
Weight (P5-N-PRO)
Weight (P5-23-PRO)
Power supply
Power source
Power consumption
W21.8cm, H21.8cm, D7.0cm
W33.5cm, H33.5cm, D9.0cm
2 kg
3.3kg
48 VDC active PoE (802.3af)
100 – 240V AC
8W
Environmental
Operating temperature
Humidity
-40°C ~ +85°C
0 ~ 90 % (non-condensing)
Management
Installation assistant
System configuration
Interfaces
Management system
LED screen
User-friendly web GUI,
SSH CLI, SNMP v1/2c/3 with
traps, centralized Remote
WNMS
Regulatory
Certification
Ingress protection
RoHs
FCC/IC/CE
IP-67
Compliant
Antenna spec (PYX-P5-23-PRO)
RF patterns (vertical)
RF pattern (horizontal)
P
Pyxis Link
IS
YX
PYX-P5-23/N PRO+
P
5Ghz Bonding + Reduncancy
PTP Link
IS
YX
400/220Mbps
Real TCP/IP Throughput
1+1 & 2+0 Bonding
Layer 2 & Layer 3 QOS
140000+
PACKETS PER SECOND
Key Features
• 5 GHz PTP bridge, ideal for: Dedicated
Access, Backhaul,Private networks
• Flexible center channel and channel width
capability (20/40 MHz) for throughput
optimization
• Radio rate of up to 300Mbps
• True aggregate throughput up to 220 Mbps
• Advanced proprietary W-jet MiMo 2
wireless protocol
• High packet-per-second (PPS) rate – ideal
for VOIP backhaul applications (140000)
• Low packet latency (2ms)
• Great spectral efficiency (7.5 bit/Hz)
• ARQ (Selective Repeat) for very high
throughput
• Dynamic TDD for allocating bandwidth in
real-time to the direction needed
• 2nd Ethernet port used to bond two links
together
wireless technology specialists
• L2 and L3 QoS support
• PoE built-in for single cable installation
(802.3 af compatible)
• 2 x 1000 BaseT Ethernet ports
• 28 dBm (per chain) integrated radio
• Advanced security technologies
• Comprehensive management features: Web
GUI, Command line management via SSH,
WNMS server support for configuration,
SNMP V1/2/3 with traps supporting
MIBs:802.11, 802.1x, MIBII, Syslog support,
Compatible with LigoWave link calculator,
Real-time alerts
• Rugged articulating bracket solution for
multi-facet mounting
• OLED screen for antenna alignment
• IP-67 compliant
Warrington Lane, Lymm,
Warrington WA13 0SW
Tel: 0161 241 0557
www.cdndistribution.co.uk
Link Bonding:
Link bonding is a new functionality available in PYX-P5-PRO+ devices. An
extremely powerful CPU allows bonding PYX-P5-PRO+ together with PYX-P5-PRO+
MiMO or PYX-P5-N-PRO+ series devices. The 2nd Ethernet port is where the
additional device is connected. Fair queuing mechanism is used for bonding of two
links operating simultaneously. Besides doubling the throughput over the same link
(from 200 Mbps to 400 Mbps) it also provides redundancy for the wireless radios; if
one of the radios fails the other link will continue to operate. As the bonding is
done in the CPU it works efficiently even when the traffic is coming from one MAC
address (for example router). The scheme of the bonded PYX-P5-PRO+ link can be
seen below Image:
Layer 2 & Layer3
QOS for Voice, Data,
CCTV video, Internet
application
Radio SPEC
Wireless Technology
Proprietary TDD protocol,
5GHz 2x2 MIMO 300Mbps
Operating mode
Point-to-point only
Radio frequency band
5.150 - 5.915GHz
(Country dependent)
Channel Size
20/40 MHz
Max transmit power
28 (+/-2) dBm
(Country dependent)
Modulation schemes
BPSK, QPSK, 16QAM, 64QAM
Receive sensitivity
Varying between -94 and
Link Performance
Single link throughput
220 Mbps aggregate (110
Mbps full-duplex)
Bonded link throughput 400 Mbps aggregate (200
Mbps full-duplex)
Max packets per second 140000
Packet latency
2 ms (64 bytes packet)
Link distance**
More than 100km (62,17 mi)
Security
Data encryption
Hardware based AES
W21.8cm, H21.8cm, D7.0cm
W33.5cm, H33.5cm, D9.0cm
2.1 kg
3.4 kg
48 VDC, active PoE (802.3af)
100 – 240V AC
12W
Type
Physical
Dimensions (P5-23-PRO)
modulation and channel size Dimensions (P5-N-PRO)
Weight (P5-N-PRO)
FEC, Selective ARQ
Dynamic time division duplex Weight (P5-23-PRO)
Power supply
Power source
Power consumption
Integrated directional panel
Polarization
(PYX-P5-23 PRO+) or 2 N-Type Environmental
Connectors (PYX-P5-N-PRO+) Operating temperature
Humidity
Dual (PYX-P5-23 PRO+)
-40°C ~ +85°C
0 ~ 90 % (non-condensing)
Gain V/H
23/23 dBi (PYX-P5-23-PRO+)
3dB Beam-width V/H
8/8 degrees
-72 dBm depending on
Error correction
Duplexing scheme
Antenna SPEC
(PYX-P5-23 PRO+)
Management
Installation assistant
System configuration
Interfaces
Physical Interface
2 x 10/100/1000 BaseT
Management system
LED screen
User-friendly web GUI,
SSH CLI, SNMP v1/2c/3 with
traps, centralized Remote
WNMS
Protocol
Ethernet IEEE 802.3
Connector type
RJ45
Surge Protection
Built-in (IEC 61000-4-2 (ESD)
Regulatory
Certification
Ingress protection
RoHs
FCC/IC/CE
IP-67
Compliant
Data Interface
and IEC 61000-4-5 (SURGE))
Antenna spec (PYX-P5-23-PRO+)
RF patterns (vertical)
RF pattern (horizontal)
P
Pyxis Link
IS
YX
PYX-P5-90
P
5Ghz PTMP Outdoor BS
with 90° Sector Antenna
IS
YX
PTMP ~ 7km
Real Throughput 160Mbps
Key Features
• Multi mode supported AP PTMP/PTP/Bridge Mode
• Radio rate 300Mbps
• Cost Effective long range PTMP
• True aggregate throughput up to 160Mbps
• Advanced proprietary TDD MiMo Wireless Protocol - Less interference
• Low packet latency
• Spectrum analyser for site survey
• TDD for allocating bandwidth
• Integrated 90° 18dBi MiMo Sector antenna
• 29 dBm TX Radio
• Management features: Web GUI, SSH SNMP V1/2/3, Syslog server
• LED Signal indicator for antenna alignment
• IP-66 Weather Proof Housing
wireless technology specialists
Warrington Lane, Lymm,
Warrington WA13 0SW
Tel: 0161 241 0557
www.cdndistribution.co.uk
Radio SPEC
WLAN standard
Radio mode
Operating modes
Radio frequency band
Transmit power
Receive sensitivity
Channel size
Modulation schemes
Data rates
Error correction
Duplexing scheme
Antenna SPEC
Type
Gain
Polarization
Cross-pol- Isolation
Max VSWR
H-pol Beamwidth
V-pol Beamwidth
Elevation Beamwidth
IEEE 802.11 a/n, TDD
(proprietary)
MIMO 2x2
Access point, CPE, WDS
Bridge mode, PTMP BS,
PTMP CPE
5.1 - 5.9GHz
(Country dependent)
Up to 29 dBm
(Country dependent)
Varying between -95 and
-75 dBm depending on
modulation
20, 40 MHz
802.11 a/n: OFDM (64-QAM,
16-QAM, QPSK, BPSK)
802.11 n: 300, 270, 240,
180, 120, 90, 60, 30 Mbps
802.11 a: 54, 48, 36, 24,
18, 12, 9, 6 Mbps
FEC, Selective ARQ
Time division duplex
Integrated 90° Sector dualpolarized
18 dBi
Dual Linear
24dBi
1:7:1
90°
90°
20°
Antenna spec (PYX-P5-90)
Wired
Interface
Networking
Operating modes
WAN
NAT
Static routing
DHCP
Port forwarding
VLAN
Physical
Dimensions
Weight
Power supply
Power source
Power consumption
10/100 Base-T, RJ45
Bridge, Router
Static IP, DHCP client, PPPoE
client
Routing w/ or w/o NAT
Supported
Client, Server, Relay
Supported
Supported for management
and data
L43cm, W15cm, H4cm
1 kg
12 - 48 V DC passive PoE
100 – 240 VAC via included
adapter
6.5 W
Environmental
Operating temperature -40°C ~ +65°C
Humidity
0 ~ 90 % (non-condensing)
Management
System configuration
System monitoring
Regulatory
Certification
User-friendly web GUI,
Command line via SSH
SNMP v1/2c/3 server, Syslogs,
system alerts via e-mail and
SNMP trap
FCC/CE/Safety/RoHS
compliance