Service Manual - Michael Jay Lissner
Transcription
Service Manual - Michael Jay Lissner
Service Manual ViewSonic PJ513D-1 Model No. VS11959 Multimedia DLP Projector (PJ513D-1_SM Rev. 1b May. 2009) ViewSonic 381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583 Copyright Copyright © 2009 by ViewSonic Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation. Disclaimer ViewSonic makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranty of merchantability or fitness for any particular purpose. Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes. Trademarks Optiquest is a registered trademark of ViewSonic Corporation. ViewSonic is a registered trademark of ViewSonic Corporation. All other trademarks used within this document are the property of their respective owners. Product disposal at end of product life The lamp in this product contains mercury. Please dispose of in accordance with local, state or federal laws. Revision History Revision SM Editing Date ECR Number Description of Changes 1a 12/17/2007 Initial Release Jamie Chang 1b 05/12/2009 Update RS232 PIN definition, IR code Sophia Kao i ViewSonic Corporation Confidential - Do Not Copy Editor PJ513D-1 TABLE OF CONTENTS 1. Introduction 1 2. Specifications 2 3. Keyboard and Remote Control keys 15 4. IR Code / RS232 Command 18 5. Adjustment Procedure 22 6 Troubleshooting 82 7. Block Diagram 90 8 Schematic Diagrams 91 9. PCB Layout Diagrams 107 10. Exploded Diagrams 109 11. Recommended Spare Parts List 117 ii ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 1. Introduction This section contains general service information, please read through carefully. It should be stored for easy access place. Important Service Information Safety Notice 1 2 3 4 5 6 7 8 9 Make sure your working environment is dry and clean, and meets all government safety requirements. Ensure that other persons are safe while you are servicing the product. DO NOT perform any action that may cause a hazard to the customer or make the product unsafe. Use proper safety devices to ensure your personal safety. Always use approved tools and test equipment for servicing. Never assume the product’s power is disconnected from the mains power supply. Check that it is disconnected before opening the product’s cabinet. Modules containing electrical components are sensitive to electrostatic discharge (ESD). Follow ESD safety procedures while handling these parts. Some products contain more than one battery. Do not disassemble any battery, or expose it to high temperatures such as throwing into fire, or it may explode. Refer to government requirements for battery recycling or disposal. General Descriptions This Service Manual contains general information. There are 3 levels of service: Level 1: Cosmetic / Appearance / Alignment Service Level 2: Circuit Board or Standard Parts Replacement Level 3: Component Repair to Circuit Boards 1 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 2. Specification 1.0 Optical Performance 1.1 ANSI Brightness Tested under 60” (diagonal) image size with Wide projection lens position unless other specified. Minimum 1600 Lumens 1.2 Brightness Uniformity 1.2.1 ANSI Uniformity Minimum 55% 1.2.2 Upper-Down unbalance 0.5~2 1.2.3 Left-Right unbalance 0.6~1.67 1.2.4 JBMA Uniformity Minimum 60% 1.3 Contrast Ratio 1.3.1 ANSI Contrast Minimum 150:1 1.3.2 FOFO Contrast Minimum 1200:1 1.4 Light Leakage <0.5 lux compared to center point within 60” (Diagonal at 2.2m, Wide) 1.4.1 Light Leakage in Active Area image size. Note: This light leakage in Active area is only described as the spot light with obvious shape. It is not included the uniformity difference of the projector for black pattern. 1.4.2 Light Leakage out of Active Area <0.65 lux with 54”~80“(Diagonal at 2m, Wide) image size 1.5 Color X Y 1.5.1 White 0.312±0.04 0.354±0.04 1.5.2 Red 0.640±0.04 0.345±0.04 1.5.3 Green 0.355±0.04 0.548±0.04 1.5.4 Blue 0.141±0.04 0.087±0.04 1.6 Color Uniformity X Y 1.6.1 White 0.040 0.040 1.6.2 Red 0.040 0.040 1.6.3 Green 0.040 0.040 1.6.4 Blue 0.040 0.040 2.0 Image Quality 2.1 Throw Ratio 54”±5% Diagonal at 2m, Wide 2.2 Zoom Ratio (tolerance applied) > 1.10 : 1 2.3 Distortion 2.3.1 Keystone Distortion <1.0% 2.3.2 Vertical TV Distortion <1.0% 2.3.3 Screen distortion l W2-W1 l <6mm , l H2 –H1 l <6 mm 2.4 Projection Offset 120% ±5% 2.5 Focus Range 2.5.1 Visible Range 1~8 m 2 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 2.5.2 Clearly Focus Range 1.5~6 m(Spec. defined as item 2.6) 2.6 Focus 2.6.1 区 Pattern (1)If pattern can be uniformly focused, pass! (2)If not, check 2.6.2 Defocus: R<=3.0; G<=2.5; B<=2.5 pixel 2.6.2 Defocus and Flare Flare: R<=4.0; G<=3.5; B<=3.5 pixel Slight flare is not counted as flare. 2.6.3 Focus unbalance Adjust focus from near to far until one corner clear, difference less than 70 cm@60” Center of 49” diagonal area 2.7 Lateral Color All other area R-G <2/3 <1 G-B <2/3 <1 R-B <1 <1 2.8 Image Quality 2.8.1 DMD Image Quality - 2.8.2 Image Imperfection Procedure: 1. 54” (Diagonal at 2m, Wide) image size. 2. Default preset mode “ Dynamic” 2.8.3 Image Shadow or Blur 3. Full white pattern to check the image. Let the projector on the desk (don’t move it up/down or left/ right) and just inspect the pattern. 4. Compare to the limit sample of OOB. If blur or shadow worse than OOB, than NG 1. When RGB value of content input is smaller than 20%, system will automatically switch to Eco mode, if RGB value is greater than 60%, the 2.9 Dynamic Contrast Ratio (DCR) projector will back to Normal mode. 2. When DCR function turns on, lamp mode function is grayed out to disable; when DCR function turns off, lamp mode would return to setting value. 3.0 Mechanical Specification 3.1 Dimensions 263 x 218 x 108mm (L x W x H) 3.2 Weight 2.6Kgw ± 0.1Kgw 3.3 Security Slot Kensington compatible slot 150N break away force 3.5 Lens Cover Detached Lens Cover 3.6 Feet Fast adjustable foot in front, Adjustable foot and Fixed foot in rear. foot Tilt:0-6∘,right/left: +2.2∘/-0.5∘ 4.0 Packaging 4.1 Outside Dimensions 370 x 186 x 297mm (L x W x H) 4.2 Weight 3.76Kgw ± 0.1Kgw (Including Accessories, Projector). 3 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 72 units by Air; 4.3 Palletization 108 units (pallet A)/72 units (pallet B) by sea 2232 units/40’ container, or 1080 units /20’ container 5.0 Thermal Specification Mechanical component temperature at ambience 0~40℃ Normal surface: 5.1 Surface held or touched for short Metal < 60°C except screws & terminals periods Plastic<65°C except around ventilation (for this model only) Screw and terminals <55°C 5.2 Surface which may be touched 5.3 Exhaust Air Metal Plastic <70°C <95°C <95°C around ventilation holes 6.0 Environmental 6.1 Temperature 6.2 Humidity Operating 0~40°C, without condensation Storage -20~60°C, without condensation Operating 10~90%RH, without condensation Storage 10~90%RH, without condensation Typical 6.3 Audible Noise Level Maximum Normal mode: 32dBA @ 25°C Eco mode: 28dBA @ 25°C Normal mode: 34BA @ 25°C Eco mode: 30dBA @ 25°C Operating: 0~6000ft,25°C±5°C 6000ft~10000ft, 25°C±5°C must be operational and the reliability decrease 6.4 Altitude is acceptable (not guarantee Power, Ballast, DMD and lamp life) Storage: 0 to +40000ft sea level(-20 °C to 30°C) Max altitude in 60°C :0-6500ft Max temperature in 10000ft:53°C Safety 7.0 Regulatory CB, CSA, TUV-GS, CCC, PSB, NOM, Korean-eK, Gost-R, Hygiene, SASO, TUV-Argentina, Ukraine, CE EMC FCC Class B requirements, CE ESD Qisda ESD Specification 8.0 Reliability 8.1 MTBF 8.2 Lamp Lifetime 40000 hours except DMD chip, Color wheel, Lamp and Ballast Normal : 2000 hours (50% brightness maintenance) Eco: 3000 hours 9.0 Power Requirements Adhere to Appendix 3.5 9.1 Power Supply (Normal) VAC 90 – 264 Auto-switch (50/60Hz), 3 Wire Grounded 9.2 Power consumption Typical 260 W Max. Standby 5W Max. 4 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 9.3 Power Connector IEC-06 10.0 Panel Specification 10.1 Type Single Chip 0.55” XGA 12 tilt DDR DMD Single Chip 0.55” SVGA 12 tilt LVDS DMD 10.2 Pixels 800 X 600 10.3 Color Depth 24 Bits (16770000 colors) 11.0 Compatibility Adhere to Appendix 3 PC Compatible 640X480 Æ 800X600, compressed 1024 X 11.1 PC 768 1280X1024; Composite-Sync; Sync-on-Green; Interlace Mode (8514A); 11.2 Video NTSC/ NTSC4.43/ PAL (Including PAL-M, PAL-N)/ SECAM/ PAL60/ 11.3 YpbPr NTSC (480i)/ 480p/ PAL (576i)/ 576p, HDTV (720p/ 1080i) 11.4 DDC DDC 2B 12.0 Image Interface Adhere to Appendix 3.2 15 pin D-Sub (Female) x 1 12.1 Analog RGB Input G(Y): Video amplitude 0.7/1.0 Vp-p : Impedance 75 RB(CbCr): Video amplitude 0.7 Vp-p : Impedance 75 HD/VD/CS: TTL Level 12.2 Video Input RCA jack (Yellow) Video amplitude 1.0 Vp-p : Impedance 75Ω 4 pin Mini-Din (Female) 12.3 S-Video Input Y: Luminance amplitude 1.0 Vp-p : Impedance 75Ω C: Chroma amplitude 0.268 Vp-p : Impedance 75Ω 12.4 YPbPr Input 15 pin D-Sub (Female) x 1 (Including 12.1) Y: Luminance amplitude 1.0 Vp-p: Impedance 75Ω PbPr/CbCr: Chroma amplitude 0.7 Vp-p : Impedance 75Ω 12.5 DVI-A Input N/A 12.6 Analog RGB Output 15 pin D-Sub (Female) x 1 G: Video amplitude 0.7/1.0 Vp-p : Impedance 75 RB: Video amplitude 0.7 Vp-p : Impedance 75 HD/VD/CS: TTL Level 13.0 Control Interface 13.1 IR Receiver IR Receiver x2 Angle: ±30° Distance 0~8m 13.2 Serial Connector RS232 8pin Mini DIN 13.3 USB Connector N/A 14.0 User Interface Adhere to Appendix 3.3 9 Keys: 14.1 Operator Keypad Power ; Source ; Auto; Left/Blank; Right/Panel key lock ; Mode/Enter ; Up/Keystone+ ; Down/Keystone-; Menu/Exit 14.2 Indicators 3 LEDs: Power On/Off Status; Lamp Status; Temperature Status 5 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 14.3 Electric Keystone vertical keystone and adjustable range 40 15.0 Audio 15.1 Audio Input 15.2 Speaker Φ3.5mm stereo mini jack x1 500mVrms, 10kΩ Sound system: Mono Speaker : 2Wx1 Amplifier: Philips PCA8551 Frequency Response: 100-20KHz Distortion: Amplifier output 1W at 10% distortion 15.3 Audio Output N/A 16.0 Option Box 16.1 Wireless function N/A 16.2 Audio Output N/A 16.3 LAN function N/A 6 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 DDC Table (EDID FILE) +0 00 20 7A 88 31 01 1C 00 30 00 00 00 20 0 10 20 30 40 50 60 70 80 90 100 110 120 Address +1 FF C5 00 23 59 01 20 1E 37 00 0A FC 20 +2 FF 01 00 15 61 01 28 00 30 00 20 00 20 +3 FF 01 78 52 59 01 80 00 31 FD 20 50 20 +4 FF 01 0A 59 81 A0 14 00 30 00 20 4A 20 +5 FF 01 F1 AD 80 0F 00 FF 30 32 20 35 20 +6 FF 01 A7 CE 01 20 00 00 30 57 20 31 00 +7 00 11 A5 00 01 00 00 51 30 1E 20 33 51 +8 5A 01 56 45 01 31 00 54 31 64 00 44 +9 63 03 5D 59 01 58 00 59 0A FF 00 0A Data description 00 - 07 Fixed Data(EDID header) 08 - 09 10 - ID Manufacturer Name: VSC = 5Ah 63h (Alphabet number transformed to hex scale from binary) 11 ID Product Code: 20h, C5h 12 - 15 Not Used 16 Week of Manufacture: 01 (for example; variable) 17 Year of Manufacture: 2007 (for example; variable) 18 EDID Structure Version No.: 1 19 EDID Structure Revision No.: 3 20 Video Input Definition: Analog Signal 0.700V/0.000V Sync: Separate Set up - V Composite Serration Display Gamma: 2.2 24 DPMS Supported Feature: V - 21 - 22 Maximum Horizontal Image Size: 0cm 23 V On Green Maximum Vertical Image Size: 0cm Stand by - Suspend - Active off - Display Type: R/G/B color display Standard Default Color Space: unused Preferred Timing Mode: supported GTF supported: not supported 25 - 34 Chroma Information: 35 36 Red x = 0.634766 y =0.338867 Green x = 0.368164 y = 0.544922 Blue x = 0.147461 y =7.51953e-002 White x = 0.313477 y = 0.34375 Established Timing I Support: 720X400 @70Hz V 720X400 @88Hz - 640X480 @60Hz 640X480 @72Hz V 640X480 @75Hz V 800X600 @56Hz V 640X480 @67Hz - - 800X600 @60Hz V 1024X768 @87Hz - Established Timing II Support: 800X600 @72Hz V 800X600 @75Hz V 832X624 @75Hz 1024X768 @60Hz V 1024X768 @70Hz V 1024X768 @75Hz V 1280X1024 @75Hz 7 ViewSonic Corporation Confidential - Do Not Copy V- PJ513D-1 37 Established Timing III Support: Reserved - Reserved - Reserved - Reserved - Reserved - Reserved - Reserved - Reserved - 38 - 53 Standard Timing Identification: #1 60X480 @85Hz #2 800X600 @85Hz #3 1024X768 @85Hz #4 1280X1024 @60Hz #5 Non-Description #6 Non-Description #7 Non-Description #8 Non-Description 54 - 125 Descriptor Description 54 - 71 Detailed Timing Description #1: 800x600 @60Hz Pixel Clock = 40.00 MHz Horizontal Image Size = 0 mm Vertical Image Size = 0 mm Refresh mode: Non Interlaced Normal display, no stereo Horizontal Active Time = 800 pixels Blanking Time = 256 pixels Sync Offset = 40 pixels Sync Pulse Width = 128 pixels Border = 0 pixels Frequency = 37.88 kHz Vertical Active Time = 600 lines Blanking Time = 28 lines Sync Offset = 1 lines Sync Pulse Width = 4 lines Border = 0 lines Frequency = 60 Hz Sync configuration: Digital Separate V sync: NEGA H sync: NEGA 72 - 89 Serial Number (Each word to be transformed in ASCII code) 90 - 107 Monitor Description Monitor Range Limits: Vertical Frequency (min.) = 50Hz Vertical Frequency (max.) = 87 Hz Horizontal Frequency (min.) = 30 kHz Horizontal Frequency (max.) = 100 kHz Maximum Supported Pixel Clock = 110 MHz GTF Standard is unused. 108 - 125 Monitor Description Monitor Name: PJ513D 126 Extension Flag: 0 127 Checksum: 51 (for example; variable) 8 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Screw List /Torque Model name : PJ513D No. M2.0 1 Screw P/N Description Type 8F.1A522.6R0 MACH Head PHM Length Coating 6 NI Q’TY 1 Torque Where use (kgf-cm) 2.5±0.5 Holder adjust foot & Fix block (1*) Engine HSG & Power BD Shielding 2 8F.1G524.5R0 MACH CAP 5 NI 1 4.5±0.5 (1*) Blower BKT BTM & Lower Case(2*) 3 8F.VA564.6R0 TAP (D-PT) 5.5±0.5 PHM 6 NI 12 8F.1A524.6R0 MACH PHM 8 NI 2 Power Board S/W & Lower Case(2*) Lamp Box & Lower Case(2*) 5.5±0.5 4 Ballast & Lower Case(3*) Ceiling Mount Plate & Lower Case(3*) 4.5±0.5 Lamp Door & Lower Case (2*) M3.0 Blower BKT & Nozzle(1*) 5 8F.1A524.5R0 MACH PHM 5 NI 8 4.5±0.5 Main BD Shielding & Power BD Shielding(5*) Speaker & Rear Cover (2*) 6 8F.VA564.100 7 8F.VG19.8R0 8 8F.VA564.8R0 9 8G.00020.423 TAP (D-PT) TAP TAP (D-PT) NUT PHM 10 NI 4 7.5±0.5 Upper Case & Lower Case(4*) CAP 8 NI 3 7.0±0.5 PHM 8 NI 3 6.0±0.5 Engine HSG & Lower Case(3*) HEX 3 NI 1 2.5±0.5 Rear adjust foot top(1*) Lower Case & Power BD Shielding (3*) AC Wire & Power BD Shielding(1*) M4.0 10 8F.1D526.6R0 MACH TAPTILE 8 NI 4 5.5±0.5 Ceiling Mount Plate & Lower Case(3*) #4-40 11 8F.00480.120 MACH STAND 8 NI 4 4.5±0.5 Rear Case & D-SUB(4*) 9 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 1. Timing Table The Default timing is as following: Resolution Mode Refresh rate (Hz) H-frequency (kHz) Clock (MHz) 720 x 400 720x400_70 70.087 31.47 28.322 VGA_60 59.940 31.469 25.175 VGA_72 72.809 37.861 31.500 VGA_75 75.000 37.500 31.500 VGA_85 85.008 43.269 36.000 SVGA_60 60.317 37.879 40.000 SVGA_72 72.188 48.077 50.000 SVGA_75 75.000 46.875 49.500 SVGA_85 85.061 53.674 56.250 XGA_60 60.004 48.363 65.000 XGA_70 70.069 56.476 75.000 XGA_75 75.029 60.023 78.750 XGA_85 84.997 68.667 94.500 SXGA3_60 60.020 63.981 108.000 640 x 480 800 x 600 1024 x 768 1280 x 1024 YPbPr support timing is as following: Signal format fh(kHz) fv(Hz) 480i(525i)@60Hz 15.73 59.94 480p(525p)@60Hz 31.47 59.94 576i(625i)@50Hz 15.63 50.00 576p(625p)@50Hz 31.25 50.00 720p(750p)@60Hz 45.00 60.00 720p(750p)@50Hz 37.50 50.00 1080i(1125i)@60Hz 33.75 60.00 1080i(1125i)@50Hz 28.13 50.00 Video, S-Video support timing is as following: Video mode fh(kHz) fv(Hz) fsc(MHz) NTSC 15.73 60 3.58 PAL 15.63 50 4.43 SECAM 15.63 50 4.25 or 4.41 PAL-M 15.73 60 3.58 PAL-N 15.63 50 3.58 PAL-60 15.73 60 4.43 NTSC4.43 15.73 60 4.43 10 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 2. Characteristics of inputs/outputs Signal Parameter RDATA GDATA BDATA GDATA_SOG HDATA Min Type Max Impedance 75 Ohm Amplitude 0.7 Volts peak-to-peak Black pedestal 0 Volts Pixel Clock 110 M Hz Impedance 75 Ohm Amplitude 1 Volts peak-to-peak Video amplitude 0.7 Volts peak-to-peak Sync amplitude 0.3 Volts peak-to-peak Black pedestal 0 Volts Pixel Clock 110 M Hz Impedance 1 K ohm Amplitude, low level 0 0.8 volt Amplitude, high level 2.5 5 Volt Frequency 31 82 K Hz Impedance 1 K ohm Amplitude, low level 0 0.8 volt Amplitude, high level 2.5 5 Volt Frequency 48 85 Hz Amplitude, low level 0 0.8 volt Amplitude, high level 2.5 5 Volt Amplitude, low level 0 0.8 volt Amplitude, high level 2.5 5 Volt RXD Amplitude -25 25 Volt TXD Amplitude -25 25 Volt VDATA SDADATA SCLDATA Amplitude, total (video+ sync) 1 Volts peak to peak Amplitude, video 0.7 Volts peak to peak Amplitude, sync 0.3 Volts peak to peak Impedance 75 ohm Amplitude 300 m Volts peak to peak Impedance 75 ohm Impedance (audio in) 10 Kohm CVBS Luminance CVBS Chroma Audio Amplitude (audio in) 0 0.30 Bandwidth 300Hz 16kHz S/N Ratio 40 Total Harmonic Distortion % 10 11 ViewSonic Corporation Volts rms Confidential - Do Not Copy % PJ513D-1 3. Electrical Interface Character Interface Definition • 15 pin definition of the mini D-sub male for DDC2B protocol 5 1 6 10 15 11 Pin Definition Pin 1 Red video (Pr) 2 5 • Definition Pin Definition Pin Definition Green Video (Y) Red Video Return 3 Blue Video (Pb) Green Video Return Monitor ID bit 0 Data clock (SCL) 4 NC 8 Blue Video Return Bi-directional data (SDA) NC 6 9 NC 10 Sync. Return 11 13 Horizontal Sync 14 Vertical Sync 15 Pin 1 Composite input S-Video input 4 3 2 • 12 Video Input 1 • 7 1 Definition Composite video input Pin 1 2 Description GND GND Luminance Chroma 3 4 Control Port 8 7 5 6 4 2 3 1 RS232 cable : 12 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 PC side Function CONN1 name 3 TXD 7 RTS 4 NC 5 GND 8 CTS 1 NC 2 RXD 9 NC 6 NC COLOR of Wire Black Brown Red Orange Yellow Green Blue White Projector side CONN2 Function name 1 2 3 4 5 6 7 8 RXD CTS NC GND RTS NC TXD NC 13 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 4. Functionality The Following functionality will be supported: (Detailed description refer to SW Specification) Functionality Data (Computer) Video/S-Video YPbPr/YCbCr Preset Mode YES YES YES Brightness YES YES YES Contrast YES YES YES Color NO YES YES Tint NO YES YES Sharpness NO YES NO Color Temp YES YES YES H. Position YES NO YES V. Position YES NO YES H. Phase YES NO YES H. Size YES NO YES Keystone YES YES YES Language YES YES YES Auto YES YES YES Image Ratio YES YES YES Auto Off YES YES YES Mirror YES YES YES Source YES YES YES Freeze YES YES YES Blank YES YES YES Lamp Reset YES YES YES OSD Timer YES YES YES Source Scan YES YES YES Keystone Hold YES YES YES Mirror Hold YES YES YES Blank Time YES YES YES Information YES YES YES Reset YES YES YES External Message indicator (Detailed description refer to SW Specification) Message Occasion PC/Composite Video /S-Video /Analog YPbPr Searching The system does not detect the signal Out of range The signal is over the specification NOTICE :Order replacement lamp , Lamp > 2000 hours Lamp Hour is over 2000 hours NOTICE: Replacement lamp soon, Lamp > 2950 Hours Lamp Hour is over 2950 hours NOTICE: Replacement lamp Now, Lamp > 3000 Hours, Lamp Hour is over 3000 hours. Lamp-usage time exceeded. 14 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 5 Power Supply Specification 5.1. Input Power Specification Specification Description Input Voltage Range The unit shall meet all the operating requirements with the range 90 ~ 264 VAC Frequency Range The unit shall meet all the operating requirements with an input frequency range 50 Hz ~ 60 Hz Power Consumption Normal operation: 260 W (Max) standby mode: < 5 W Regulation Efficiency 80 % (typical) measuring at 115Vac and full load 5.2. Output Power Requirement The power supply can provide DC output as below: NO. Voltage 1 2 Regulation Load Current Range Ripple & Noise +5 V ±5 % 0.06A ~ 0.5 A 100 mV +12 V ±10 % 0.04 A ~ 1.25A 300 mV 5.3. Lamp Power specifications Specification Description Applicable Lamp 180W, AC operation Starting pulse from Ignitor 2.5KV 5.4. Others Item Power good signal High voltage and high temperature protection Description Active high after 5 Volt reach 95% of its rating and goes to logic low at least 0.5ms before power falls to 90% of its rating To avoid user from the dangerous of HV and high temperature, when front door of lamp case is opened whether intentionally or accidentally, the power should be disconnected immediately. When the door is closed again, the igniter restart sequence should be compliant to that is described previously 15 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 3. Keyboard and Remote Control keys Local Keyboard Description Key Name Detailed Description Power Use this button to turn your Data Projector on and off (standby mode). Source To select input sources as Computer, Video, S-Video, YpbPr Auto Toggle auto-tracking image function Left/Blank 1. When user presses the button once, the image would turn to blank and show “blank” in the right-button screen. 2. When the image is blank, user press this key back to Normal image; if user presses other buttons on keypad or remove, it would release 3. If there is OSD menu, user can press this key to move to the left item. Right/Panel Key 1. When user presses the button once, it will enter “Panel key Lock” setting. 2. When panel key is locked, user could press this key for 3 seconds to release Panel Key Lock( If the panel key lock is active, user still could use power key to turn on/off the projector)\ 3. When there is OSD menu, user can press this key to move to the right item Up/Keystone+ 1. When user presses this button once, it will increase the keystone value. 2. When there is OSD menu, user can press this key to move to upper item. Down/Keystone- 1. When user presses this button once, it will decrease the keystone value. 2. When there is OSD menu, user can press this key to move to next item. Menu/Exit 1. User could press this button to call OSD 2. When it exists OSD, user could press this button to leave current page to main menu or to close OSD. Mode/Enter 1. When there is No OSD menu, this button is Mode hot key; user would press this button to choose one of preset modes. 2. When there is confirm messages, user could press this key to confirm selection. 16 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Remote Control Keys Description IR-Key Name Detailed Description Power Use this button to turn your Data Projector on and off (standby mode). Source To select input sources as Computer, YPbPr , Video, S-Video Menu/Exit (1) OSD pop-up. (2) Close OSD or leave current page 4/Panel Key (1) Press once, enter ”Panel Key Lock” setting. (2) Press 3 seconds to release “Panel Key Lock”. (3) OSD menu, move to right items 3 5/Keystone+ (1) OSD menu, move to left item. 6/Keystone- (1) Keystone-. (2) Move item bar Auto Toggle auto-tracking image function Mode/Enter (1) Change different Preset mode (2) Press for confirm message. Freeze This button will freeze a picture. Press again to resume motion. Blank Press “Blank” key first to blank the screen. Digital Zoom + (1) Zoom in (2) Pan the picture , when picture is in Zoom in/out image. Digital Zoom - (1) Zoom out (2) Pan the picture, when picture is in Zoom in/out image. (1) Keystone+. (2) Move to page level External Status indicator LED Name Detailed Description Power LED Display the power on/off sequence status Lamp Status LED Display the Lamp status (Lamp fail, Lamp spoil etc.) Temperature Status LED Display the Thermal status (Fan Fail, Over Temperature, etc.) 17 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 4. IR Code / RS232 Command 1. IR Code CUSTOMER CODE DATA CODE FUNCTION 0030 02 POWER 0030 03 0030 04 SOURCE 0030 05 TIMER (ON) 0030 06 TIMER (SETUP) 0030 07 BLANK 0030 08 AUTO 0030 0B 0030 0C 0030 0D 0030 0E 0030 0F MENU 0030 10 MODE 0030 18 DIGITAL ZOOM + 0030 19 DIGITAL ZOOM - 2. RS-232 Command a. RS-232 connection setting value Baud Rate: 115200 Parity: None Data bits: 8 Stop bits: 1 Flow control: None b. RS-232 command code Function Status Write Power Action Turn on 0x06 0x14 0x00 0x03 0x00 0x34 0x11 0x00 0x5C Turn off 0x06 0x14 0x00 0x03 0x00 0x34 0x11 0x01 0x5D Power Read status( on/off/cool down) Excute Reset Mirror Write Read Contrast (only For User Mode) cmd Write Read 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00 0x5E 0x06 0x14 0x00 0x03 0x00 0x34 0x11 0x02 0x5E Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E H Inverse 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F V Inverse 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61 H&V Inverse 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60 Mirror status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x00 0x5F Contrast decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x00 0x60 Contrast increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x01 0x61 Contrast ratio 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x02 0x61 18 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Brightness (only For User Mode) Aspect ratio Write Read Write Read Brightness decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x00 0x61 Brightness increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x03 0x01 0x62 Brightness 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x03 0x62 Aspect ratio Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62 Aspect ratio Native 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x01 0x63 Aspect ratio 4:3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64 Aspect ratio 16:9 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65 Aspect ratio 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x04 0x63 Auto Adjust Excute 0x06 0x14 0x00 0x03 0x00 0x34 0x12 0x05 0x62 Horizontal position shift Horizontal Write position Read right 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x01 0x65 Horizontal position shift left 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x06 0x00 0x64 Horizontal position 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x06 0x65 Vertical position shift Vertical position Write Read Color temperature Write (only For User Mode) Read Blank Keystone-Vertical 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x00 0x65 down 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x07 0x01 0x66 read Vertical position 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x07 0x66 color temperatureT1 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x00 0x66 color temperatureT2 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x01 0x67 color temperatureT3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x02 0x68 color temperatureT4 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x03 0x69 color temperature status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x08 0x67 Write Blank on/off 0x06 0x14 0x00 0x03 0x00 0x34 0x12 0x09 0x66 Read Blank status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x09 0x68 Write Read Preset mode up Vertical position shift Write Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x00 0x68 Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x01 0x69 Keystone status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0A 0x69 Preset mode 0 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x00 0x69 Preset mode 1 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x01 0x6A Preset mode 2 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x02 0x6B Preset mode 3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x03 0x6C Preset mode 4 (PC User I) 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x04 0x6D Preset mode 5 (PC Freeze Source input User II ) 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x05 0x6E Read Preset mode status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0B 0x6A Write Freeze on/off 0x06 0x14 0x00 0x03 0x00 0x34 0x13 0x00 0x5E Read Freeze status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x00 0x60 Input source VGA 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0x60 Input source YPbPr 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x04 0x63 Write Composite Read Source scan Write Read Mute Input source Write Read 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x05 0x65 Input source SVIDEO 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x06 0x66 Source 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x01 0x61 Source scan on 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x01 0x62 Source scan off 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x02 0x00 0x61 Source scan status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x02 0x62 Mute on 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x01 0x61 Mute off 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x00 0x00 0x60 Mute status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x00 0x61 19 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Write Volume Read Write Language Read Lamp Time Write Read error status Increse Volume 0x06 0x14 0x00 0x03 0x00 0x34 0x14 0x01 0x60 Decrese Volume 0x06 0x14 0x00 0x03 0x00 0x34 0x14 0x02 0x61 Volume 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x03 0x64 English 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61 Français 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62 Deutsch 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63 Italiano 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64 Español 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65 РУССКИЙ 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x05 0x66 繁體中文 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x06 0x67 简体中文 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x07 0x68 日本語 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x08 0x69 한국어 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x09 0x6A Swidish 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0a 0x6B Dutch 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0b 0x6C Turkish 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0c 0x6D Czech 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0d 0x6E Portugese 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0e 0x6F Thai 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x0f 0x70 Polish 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x10 0x71 Language 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x00 0x62 Reset Lamp usuage hour Lamp usuage hour Read 0x06 0x14 0x00 0x03 0x00 0x34 0x15 0x01 0x61 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x01 0x63 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x02 0x64 Error code table To send Hex code “error status” read “0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x02 0x64”. User can get 20 byte data which mapping to below error status and the number means how many time the error appeared. Byte 0 1 2 3 4 5 6 7 Error Name LampFailCount Fan1ErrorCount Fan2ErrorCount Fan3ErrorCount Fan4ErrorCount Diode1OpenErrorCount Diode2OpenErrorCount Diode3OpenErrorCount 8 9 10 Diode1ShortErrorCount Diode2ShortErrorCount Diode3ShortErrorCount 11 Temperature1ErrorCount 12 Temperature2ErrorCount 13 14 15 16 17 18 19 Temperature3ErrorCount FanIC1ErrorCount FanIC2ErrorCount WatchdogCount AbnormalPowerdown CWErrorCount, FirstBurnInErrorMinutes Description Lamp turn on fail Fan1 fail (lamp fan) Fan2 fail (power fan) Fan3 fail (blower fan) Fan4 fail (The model without 4 fans without this error count) Thermal sensor 1 lose connection Thermal sensor 2 lose connection Thermal sensor 3 lose connection (The model without thermal sensor 3 is no function for this address) Thermal sensor 1 short (inlet sensor which located at main board) Thermal sensor 2 short (power board temperature sensor) Thermal sensor 3 short (The model without thermal sensor 3 is no function for this address) Thermal sensor 1 detect temperature over system limitation (inlet sensor which located at main board) Thermal sensor 2 detect temperature over system limitation (power board temperature sensor) Thermal sensor 3 detect temperature over system limitation (No used) Fan IC 1 fain (G743 or G794) No used The DDP2230 internal F/W watchdog function executed The user turn off unit without finish cooling process Color wheel do not spin st The timeframe from burn-in to 1 time shutdown in minute. 20 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 4. Method to enter factory menu: a) Press Menu on keypad than the main menu popup b) When showing main menu, press Source + Mode at the same time c) Factory menu popup at the top-left of display 21 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 5. Adjustment Procedure Visual Inspection & Cleaning Visual Inspection Criteria 1.0 Inspection zone definition and inspection distance A-side: Up case - Up case surfaces except right / left / behind side’s surface. Front cover - Front cover surface B-side: Side - right/left sides surfaces Back cover - Back cover surfaces C-side: Low cause - bottom surfaces z For spot inspection distance is 45 cm on A/B/C-side. And inspection time is 10 sec. z For scratch inspection distance is 45 cm on A/B/C-side. And inspection time is 10 sec. 1.1 Appearance Inspection Criteria 1.1.1 Environment Condition 1.1.1.1 Lighting intensity All appearance quality shall be inspected with the lighting condition as 500~800Lux (natural lighting or white fluorescent light). 1.1.1.2 Inspection angle and distance to object or target All part inspection must be done under direct overhead lighting. Viewing angle and distance are dependent on surface classification. In all cases, parts must be held in such that the light reflection does not disturb the inspector's eye. Figure 1 22 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Table 1 Classification Area A Lighting positioning Area B Area C Above of inspected part Inspection position relative to part 90º 90º 90º Inspection distance 40~50 cm 40~50 cm 40~50 cm 1.1.1.3 Inspection interval (time) Inspection interval is a function of surface area. Time for visual inspection: 10sec. Table 2 Parts Size “A” surface “B” surface “C” surface Time 10 sec 10 sec 10 sec TABLE 3 General Product of plastic outlook of dot, blemish, and others spec inspection standard Spec ( Area cm2 ) P < 0.2 mm2 Distance ≥ 2cm | Color spot 0.3≦P <0.4mm2 Distance ≥ 4cm Distance ≥ 2cm Particle 0.1≦P<0.2mm2 | Distance ≥ 4cm Distance ≥ 4cm color 0.3≦P < 0.5mm2 (Number of defect) (Number of defect) (Number of defect) 70*70 100*100 20*20 Distance ≥ 5cm Total Ignore 50*50 70*70 100*100 20*20 Ignore Ignore Ignore Ignore 50*50 70*70 100*100 Ignore Ignore Ignore Ignore 2 3 4 5 2 3 4 5 4 4 5 6 0 0 0 0 2 3 4 5 3 4 5 6 Ignore Ignore Ignore Spot with 0.2≦P < 0.3mm2 same C surface Ignore Ignore Ignore Distance ≥ 4cm P<0.1 mm2 B surface 20*20 50*50 Particle 0.2≦P< 0.3 mm2 Blemish A surface Ignore Ignore Ignore Ignore Ignore Ignore Ignore Ignore Ignore 4 4 5 6 5 5 6 7 6 6 7 8 3 4 4 5 4 5 5 6 6 7 7 8 2 2 3 4 3 3 4 5 4 4 5 6 4 4 5 6 5 5 6 7 6 6 7 8 Note: 1. Use the 20*20 criteria to the area less than 20*20; 50*50 inspection criteria to the area 20*20≦A<50*50; etc. (Particle/Blemish/Color Spot) 1.1 Definition of surface A, B, C refer to 6.2 1.2 Blemish around the ViewSonic Bird logo, name plate and silk screen must be equal or smaller than 0.05 mm2 1.3 Bubble on the surface is to be reject. 23 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 TABLE 2 : General Product of plastic outlook inspection standard NO Appearance 1 Shrinkage Spec A region: No Shrink. With gloves, no feeling of sink when touching the surface B/C region: not obvious 2 Run, Texture, Gloss No obvious non-uniformity 3 Welding Line/Knit Line Follow limit sample level 4 Ejector Mark 5 Label/screws shortage Reject 6 Material shortage Not allow, Reject 7 Chromatic aberration Follow engineering specification 8 Printing Printing must not have incomplete printing, break off, overlap, uneven thickness, Reject excessive ink, printing misalignment (1.5mm), printing slanting & crooked (<0.5mm) Printing color must be comparable to color chip and sample. Follow engineering specification 9 Logo of panel sticker Printing must not have incomplete printing, break off, overlap, uneven thickness, excessive ink, printing misalignment (1mm), printing slanting & crooked (<0.5mm) Printing color must be comparable to color chip and sample. 10 Scratch/Nicks Side A: (W < 0.1mm , L < 5mm): Only 2 this kind of scratch is accepted W < 0.1mm , L < 5-10mm :Only 1 this kind of scratch is accepted Side B: W < 0.2mm , L < 5mm : Only less than 2 this kind of scratch is accepted W < 0.2mm , L < 5-10mm : Only 1 this kind of scratch is accepted Side C: W < 0.3mm , L < 5mm : Only 3 this kind of scratch is accepted W < 0.3mm , L < 5-10mm : Only 2 this kind of scratch is accepted W < 0.3mm , L < 10-15mm: Only 0 this kind of scratch is accepted Note: 1. Severe scratch which disclose the Natural 2. When light scratching on it, there’s no feeling of obstruction. Also, there should not be obvious difference in gloss nearby it. 3. Each scratch should be 5cm more far away from each other 4. Front case must be no any scratch 24 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 PART II Operational Inspection Criteria TEST CONDITIONS Unless other prescription, the test conditions are as followings: Nominal voltage: refer to operation manual Environmental illumination: Variable from 500 to 800 Lux (For appearance inspection) Variable from 0 to 7 Lux (For functional inspection) Temperature: 25±5℃ Visual inspection shall be done with the distance from eyes to the sample 45 cm. Display mode: refer to operation manual TEST EQUIPMENTS Dark room PC Pattern Generator: Chroma 2327 or equivalent Minolta color analyzer CL200 or equivalent device with accredited traceability DVD player Power supply (100~240 VAC) with consumption meter Measuring tape TEST PATTERN PATTERN PATTERN Full white Full Dark Full Red TEST ITEM Acceptance Criteria ANSI (1) ANSI Brightness:(Normal Mode) 1600lm Brightness、 (2) Uniformity: ANSI: 55% (Minimum) Bright (3) Contrast Ratio : 150:1 (Minimum, by ANSI Uniformity、 Standard Checkerboard Method), 1200:1(by All FOFO White, All Black Method) Contrast (4) White Point, Color :x = 0.312±0.04, y = Ratio、 0.354±0.04 FOFO Contrast Ratio : 1200:1(by All White, All Black Contrast Ratio Method) Impurity、CIE Chromaticity : Red: x =0.640±0.04, y= 0.345±0.04 coordinate 25 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Full Green Full Blue Chromo 800x600 General-1 pattern 16 Gray and Color bar Impurity、CIE Chromaticity : Green: x =0.355±0.04, y=0.548±0.04 coordinate Impurity、CIE coordinate Chromaticity : Blue: x =0.141±0.04, y= 0.087±0.04 (1)Background lines should be distinguishable. Focus Range (2)“区”:Letter shape and lines should be distinguishable. Performance/ Timing check/ function check (1)Phase should be stable(no flick) (2)Whole frame should appear. Gray and Color bar No lack or mix color Check Check the DDC information, DDC check Including S/N, model, manufacturer name, product S/N(08-09): with numbers Model(108-125) with numbers(ref Appendix DDC table) manufacturer name(08-09):5A63 product ID code (10-11): 20C5 code. 26 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Software/Firmware Upgrade Process How to Download Firmware Hardware required 1. Standard RS-232 Download cable 2. Personal computer or laptop computer Software required 1. DDP2230 Composer lite 2. New version FW DDP2230 Composer lite install procedure Installation Location The default installation directory is: C:\Program Files\DLP Composer Lite 7.0 If you want to install to a different directory (perhaps alongside a prior release of DLP Composer™ Lite), click the "Browse" button on the "Select Features" page.. USB Support - Installation (All Platforms) This release includes support for a USB communications interface to DDP2230-based projectors. The setup program includes the files needed to install USB support (for Win98/WinMe/Win2K/WinXP only -- Win95 and WinNT are not supported). After DLP Composer™ Lite is installed, to install the USB support, choose the "Install DDP2230 USB Driver" icon under "DLP Composer™ Lite" in your Start menu. USB Support - Win98/Me/XP Only Installation on Windows 98/Me//XP may prompt "Please insert the disk labeled 'DLP Composer Installation Directory', and then click OK". This message may be safely ignored by clicking the OK button. Another prompt will then appear: "The file 'windrvr6.sys' on DLP Composer Installation Directory cannot be found". problems. Again, click OK and the installation proceeds without further 27 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 USB Support - Using a projector for the first time After installation is complete, and you plug a DDP2230-based projector into USB for the first time, Windows will run the "New Hardware Wizard". When the wizard prompts to find the necessary drivers, accept the recommended choice (let the system find the driver for you) and click "Next" to complete the installation. Note: The Windows 98/Me/XP "New Hardware Wizard" may not automatically find the driver. You should use the "Advanced" option, and enter the directory where the DLP Composer™ Lite Tool Suite was installed (normally "C:\Program Files\DLP Composer Lite"). The wizard will find the file "DDP2230.inf" and complete the installation. USB Support - Choosing the USB interface To select the USB communications interface, choose "Preferences" from the "Edit" menu, click the "Communications" page and choose "USB (DDP2000/DDP3020 Only)". You can now use DLP Composer™ Lite to communicate with a DDP2230-based projector via USB using the Flash Loader tool. 28 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Download procedure 1. Click on Flash Loader and browse the image file (new version firmware) 2. Make sure to check “Skip Boot loader area (load all but the first 32KB)” 3. Plug power cord into projector 4. Plug in RS-232 cable between computer and projector side 5. Press start download to begin update new firmware 6. 7. Wait till composer lite notice upgrade completed Download is completed. The factory settings should be restored. 29 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 1. EE Assembly and Alignment Concern: 1. Color Wheel Delay Alignment Equipment: - Battery Biased Silicon PIN Detector - Oscilloscope - Probe OSD Default value: Item Value DLP Brightness 32 DLP Contrast 32 White Peak 10 Item Value CW Delay Adjustable The default values let optical engine to get maximum contrast and brightness. Procedure: Probe impedance matches 50 ohm Open Factory OSD, and select color wheel delay item Leave the image pure red (DMD red curtain) Put the detector on the screen that red image was projected. Watch the oscilloscope and notice the square waveform Use the “Æ” and “Å” key to increment or decrement the color wheel delay value No matter the waveform is square or not, let the waveform was lagged first Lag Exact Ahead Then increment or decrement the value to let the waveform to be square Do not adjust too much, let the signal get ahead, if it happens, go back to step 7 and do it again. Change the input to pure blue and repeat the above procedures again. Change the input to pure green and repeat the above procedures again. 2. Main board check procedure Equipment: - Pattern generator Procedure: 1. Connect power, D-sub into projector. 2. Light on projector. 3. Testing below patterns and resolution is 854*480@60Hz (480P) (1) General-1 pattern. (Pattern 1) (2) 32 grays pattern. (Pattern 48) (3) White pattern. (Pattern 41) 30 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 (4) SMPTE pattern. (Pattern 5) 4. The main board would be note fail if above four image-quality is not good. 5. Test the connection between main board and IR board. 6. The main board would be note fail if there are some broken occur in wire or main board. 3. DMD Panel Alignment Equipment: - Pattern Generator Procedure: 1. Connect power, Video signal into projector. 2. Light on projector 3. Change pattern generator to full white pattern. 4. Watch the image if any pixel lost 5. Change pattern to full black. 6. Watch the image if any pixel lost 7. Change pattern from full black to full white. 8. Watch the image if any pixel can not return 9. Change pattern from full black to full white. 10. Watch the image if any pixel can not return 11. If above 8 step has some pixel lost or can not return, it’s DMD chip has pixel defect 12. Change to the Slid Line pattern 13. Watch the image if any pixel lost 14. If above step has some pixel lost, it’s conductive socket has defect or assembly loosed. 4. PC Alignment Procedure Equipment: - Pattern generator (Chroma-2250) OSD Default value: Item Value Cal R Offset 127 Cal G Offset 127 Cal B Offset 127 Cal R Gain 127 Cal G Gain 127 Cal B Gain 127 YPbPr R Offset 127 YPbPr B Offset 127 31 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Procedure: Gray Level: 1. 2. 3. 4. Connect power, D-sub, into projector. Change Timing and pattern of pattern generator: Timing: 800*600@60 Pattern: As Figure1 {A near white color (240,240,240) and a near black color(16,16,16), the area of white is 101/200, black is 99/200} 5. Light on projector 6. Set user OSD values to default. 7. Enter factory mode. 8. Set Factory values to default. 9. Press “Calibration RGB” to let the black level to just distinguish, and the light output of white level to just max. 10. Check the 32 levels of gray. All steps must appear. Figure1 32 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 5. YUV Alignment Procedure Equipment: - Pattern generator (VG-828) OSD Default value: Item Value Cal R Offset 127 Cal G Offset 127 Cal B Offset 127 Cal R Gain 127 Cal G Gain 127 Cal B Gain 127 YPbPr R Offset 127 YPbPr B Offset 127 Procedure: 1. Connect power core, YPbPr cable into projector. 2. Change timing and pattern of pattern generator: Timing: 480i Pattern: As Figure2 3. 4. 5. 6. 7. Light on projector Adjust user OSD values to default. Enter factory mode. Adjust Factory values to default. Press “Calibration YPbPr” to calibrate the mid level offset. Figure2 33 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 2. Optical Engine Assembly and Alignment Concerns 1. Assembly Lamp module: 1.1 Washer, Screw, Fin and Mesh Assembly I. Assemble Washer and Screw to the HLD Lamp(Fig. 1-1) II. Assemble “MESH” with Lamp holder .Mesh hooks HLD Lamp first (Fig. 1-2) and press it assemble to the right position (Fig. 1-3). III. Assemble “FIN” with Lamp holder and fasten screw (Fig. 1-4). Fig. 1-1 Fig. 1-2 Fig. 1-3 Fig. 1-4 34 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 1.2 Front Glass Assembly. i. ii. iii. Front Glass UV coated surface (marked) must face to Lamp. (Fig. 1-6) F/G must be placed on datum surfaces well. (Fig. 1-7) To make sure F/G Clip hooked well with HLD lamp. (Fig. 1-8) F/G datum Fig. 1-7 Fig. 1-6 Fig. 1-8 1.3 Lamp wire and Lamp Assembly. 35 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Short wire Long wire Fig. 1-9 Fig. 1-10 36 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 i. ii. iii. Insert Lamp into HLD Lamp and push Lamp forward to touch DTM Lamp of HLD Lamp (Fig. 1-11) To make sure that three datum contact with the lamp well(Fig. 1-12) After assemble Lamp to HLD Lamp, Hook “Clip down Lamp” first then Hook “Clip UP Lamp” on the HLD Lamp to fix Lamp last. (Fig. 1-13、1-14) iv. Check assembly again and make sure the three datum contact with the lamp. v. Assemble Plate Lamp to the HLD Lamp and fasten the screw(Fig. 1-15) DTM of Lamp Fig. 1-11 Fig. 1-12 Fig. 1-13 Fig. 1-14 37 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Fig. 1-15 38 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 2. BKT LINK Lamp and CW Shield Assembly 2.1. Insert CW Shield and hook BKT LINK Lamp 2.2. Fasten screw (Fig. 2-1.2-2) Fasten screw Fig. 2-1 Fig. 2-2 3. Assembly CW Module 3.1 CW Module Assembly Sequence as blow (Fig. 3-1): (1) BKT CW (2) Damper CW (3) CW (6) M2 Screw (7) Sensor Board (4) Fixed screw (5) CVR CW (8) M2 Screw 1 3 4 5 6 2 8 7 Fig. 3-1 39 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Fig. 3-2 40 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 4. Assembly Baffle Stop AL 4.1. Assemble Baffle Stop AL on HSG DMD and fasten screw (Fig. 4-1) Fig. 4-1 5. Assembly LP Module 5.1 LP must datum well with “BKT_LP” show as Figure 5-1 5.2 Referring to Figure 5-2,there must be visible clearance between “BKT_LP” and ”LP opening” after assembly。 TOP Datum Clearance RIGHT Datum Fig. 5-1 Fig.5-2 5.3 Glue “LP” and “BKT_LP” with “”UV5503 Glue” at two opening of “BKT_LP” show in Figure 5-3. 5.4 UV-5503 Glue curing process and concerns: vi. The UV-glue must fill up the whole opening area (shown in Figure 5-3) to contact well 41 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 with LP surfaces and BKT_LP. vii. Exposed to visible light at 350 ~ 420nm (at least 100mW/cm2) wavelength for 1 minute. viii. After curing, the height of UV-glue should not exceed BKT_LP for more than 0.6mm Glue 5503 Fig. 5-3 5.5 Assembly LP Module to HSG DMD i. Assembly two Overfill adjustment screw (8F.1A752.8R0) to HSG DMD (Fig. 5-4). ** Adjustment criteria refer to item 5.6. ii. Insert CLIP of BKT_LP into the hole iii. Placed LP Module on LP datum and adjustment screw well, shown (Fig. 5-6). iv. Assembly “Baffle LP” first ( Figure 5-7)and make sure it hooks HSG DMD well ~ Assembly Criteria was shown in Figure 5-7-2. v. Assembly “Clip_LP” second (Fig. 4-8) and make sure it hooks HSG DMD well. ( Figure 5-9). vi. Push two hook places to make sure that Baffle_LP touches “BKT_LP “well, don’t push the middle place of “Baffle_LP”. 5.6 Overfill Adjustment @ LP Module Overfill Adjustment Criteria: i. ii. Pre-assembly 2 adjusting screws. Criteria shown as Figure 5-10. Alignment Sequence: a. To adjust “Horizontal Adjustment Screw” firstly, then “Vertical Adjustment Screw”. b. Refer to Figure 4-10. For Overfill Re-adjustment: 1. Those 2 Adjustment Screws must be released closely to the “Pre-assembly” positions first. (defined in 4.6-i ) 42 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 2. Follow adjustment steps shown in Item 4.6-ii. (1) Overfill Vertical Adjustment Screw CLIP of BKT LP Fig.5-4 (1) Overfill Horizontal Fig. 5-5 Overfill adjustment screw LP DATUM Fig. 5-6 43 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Baffle_LP hooks HSG DMD first To ensure clip hooks HSG DMD well. BAFFLE LP This area is not allowed to be pressed while assembling Baffle Fig. 5-7 (1) Fig. 5-7(2) Clip LP Fig. 5-8 Fig. 5-9 44 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Pre-assy this screw not over the side surface. (1) Overfill Horizontal Adjustment Screw (2) Overfill Vertical Adjustment Screw Pre-assy this screw not over the bottom surface. Fig. 5-10 6. Assembly HSG ILL Module 6.1 FM1 Assembly I. FM1 must be placed on datum surfaces well and breach of FM1 must be face to inside (Fig. 6-1) II. Insert the” CLIP of FM1” into the hole on the HSG ILL and make sure ” CLIP of FM” hook on the HSG ILL well (Fig. 6-2) 6.2 CM Assembly III. Insert Clip CM Side and Clip CM Bottom first (Fig. 6-3,6-5) IV. Assemble CM to HSG ILL and to make CM contact three datum on the HSG ILL Well (Fig. 6-8) V. Assemble “CLIP of TOP” to the HSG ILL (Fig. 6-9) VI. To check and make sure “ CLIP of CM” hooks the HSG ILL very Well (Fig. 6-4, 6-6,6-10) VII. Assemble Baffle Stop to HSG ILL and fasten screw (Fig. 6-10) VIII. Paste Sponge tube AL on cannelure of HSG ILL(Fig. 6-11) 45 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Breach of FM1 Fig. 6-1 Fig. 6-2 CLUP CM DOWN Fig. 6-3 Fig. 6-4 46 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 DTM of CM Fig. 6-5 Fig. 6-6 CLIP CM SIDE Fig. 6-7 Fig. 6-8 CLIP CM TOP Fig. 6-9 Fig. 6-10 47 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Baffle Stop Fig. 6-10 Sponge Fig. 6-11 48 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 7. AL, HSG ILL and HSG DMD Assembly: 7.1 Placed “AL” on the HSG DMD .The “raised surface” of “AL” shall toward “DMD direction” (Fig. 7-1) 7.2 Assemble” HSG ILL Module” to HSG DMD and cover over on “AL” (Fig. 7-2) DMD Direction AL Fig. 7-1 Fig. 7-2 8. DMD and Chip B/D Module 8.1. Judge Chip B/D and DMD alignment keying first (Fig. 8-1, 8-2) 8.2. Alight keying and Assemble DMD to Chip B/D (Fig. 8-3) 8.3. Push DMD slightly and use screwdriver rotate button to lock DMD on Chip B/D (Fig. 8-4) Alignment keying Fig. 8-1 Fig. 8-2 49 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Button Fig. 8-3 Fig. 8-4 9. AL , HSG ILL and HSG DMD Assembly: 9.1 Placed “AL” on the HSG DMD .The “raised surface” of “AL” shall toward “DMD direction” (Fig. 9-1) 9.2 Assemble” HSG ILL Module” to HSG DMD and cover over on “AL” (Fig. 9-2) Fig. 9-1 Fig. 9-2 50 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 10. Assembly OP ENG 10.1 Assemble Baffle DMD to HSG DMD (Fig. 10-1) 10.2 Assemble Chip B/D Module to HSG DMD and fasten the screw(Fig. 10-2) Fig. 10-1 Fig. 10-2 10.3 Fasten shoulder screw Sequence as blow (Fig. 10-3) i. ii. iii. Pre-fastening Sequence: [ 1 ] - [ 2 ] - [ 3 ] - [ 4 ] Fastening Sequence [ 2 ] - [ 1 ] - [ 4 ] - [ 3 ] Screw Torque must be confirmed to be 2.5 kg-cm. 1 3 4 2 Fig. 10-3 51 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 10.4 Assemble PL Lens and fasten screw (Fig. 10-4) 10.5 Assemble Ring Zoom and fasten screw then assembly Ring Focus(Fig. 10-5) Ring Focus Ring Zoom Screw Fig. 10-4 Fig. 10-5 10.6 Assemble CW Module and fasten screw (Fig. 10-6) Fig. 10-6 10.7 Assemble BKT Link and Shield CW (Fig. 10-7) 52 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Fig. 10-7 53 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 10.8-1 Assemble Thermal pad and Hest-sink 10.8-2 Fasten “Assy spring screw” Sequence as blow (Fig.10-8) Pre-fastening Sequence: [ 1 ] - [ 2 ] Fastening Sequence [ 2 ] - [ 1 ] Screw Torque must be confirmed to be 6 kg-cm. 2 1 Fig. 10-8 10.9 Assemble Lamp Module and fasten screw (Fig. 10-9) 54 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Fig. 10-9 55 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 3. Mechanical Assembly Concern 3.1. Ballast assembly and lamp wire alignment 3.2. Blower module assembly and blower wire alignment 3.3. OPT engine assembly and blower wire alignment 3.4. Power board assembly and power board wire alignment 3.5. Lamp box assembly 3.6. Power board shielding assembly and power board grounding wire alignment 3.7. Main board assembly and ballast wire alignment 3.8. Main board shielding assembly and wire alignment a. Main board shielding assembly b. C/W FPC, C/W sensor wire and blower wire alignment c. Front IR wire alignment 3.9. Rear cover assembly and speaker wire alignment 3.10. Twin fans assembly and wire alignment. 3.11. IR board assembly 3.12. Upper case, inlet cover and outlet cover assembly 3.1. Ballast assembly and lamp wire alignment To keep the wire into the rib 56 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 To keep the wire into the rib. To keep the wire into the rib. 3.2. Blower module assembly and blower wire alignment To keep the wire under the blower 57 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 3.3. OPT engine assembly and blower wire alignment 2. Second screw constrain 1. First screw constrain 3. Third screw constrain To keep the blower wire under the heat sink of OPT engine. 3.4. Power board assembly and power board wire alignment 58 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Step 1 To lock this screw Step 3 To plug in thermal b k i t Step 2 To lock this screw. Step 4 To plug in ballast i t Put ballast wire into this opening of power board 3.5. Lamp box assembly To keep the hook of lower case into the lamp box 59 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 To keep the FC’s mylar at left side of lamp box OK NG 3.6. Power board shielding assembly and power board grounding wire alignment To be put hole to hold lower case boss and fix. To be put hole to hold lower case boss and fix. 60 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 3. Third screw constrain 1. First screw constrain 2. Second screw constrain The fixed side of grounding wire must be take care 4. Four screw constrain OK NG 3.7. Main board assembly and ballast wire alignment To keep the wire into the gap of lower case 61 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 3.8. Main board shielding assembly and wire alignment a. Main board shielding assembly To take care, the main board shielding must keep into the gap between lamp box and power board shielding 5. Fifthly screw constrain 3. Third screw constrain 1. First screw constrain 2. Second screw constrain 4. Fourth screw constrain 62 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 b. C/W FC, C/W sensor wire & blower wire alignment To keep the redundant wire above lamp box c. Front IR wire alignment Step 1. To keep the IR wire into the saddle wire. Step 2. To plug in the connector. 63 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Step 3. To keep the IR wire under the power board shielding Step 3. To keep the IR wire under the Step 4. To keep the IR wire into h fl f OPT h i 64 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 C/W FPC Front IR wire Blower wire C/W sensor wire 3.9. Rear cover assembly and speaker wire alignment Step 1. To plug in the connector 65 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Step 2 To keep the speaker wire under the power board shielding Step 3. To keep the redundant wire to 66 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Step 4. To check the speaker wire is not i db 67 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 3.10. Twin fans assembly and wire alignment. Fan wire must keep this location. Don’t put wire on top of the fan. Do not plug in or pull out the fan connector by holding the wire. Do not pinch the wire together when assembling. 68 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 3.11. IR board assembly Step 2 Step 1 Push 69 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 3.12. Upper case, inlet cover and outlet cover assembly The rib of side cover must keep into the constrain gap of upper case. OK NG 70 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 4. Power Assembly Concern a. The wire from power to ballast -The connector near the core should be connected with the ballast. 71 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 5. EMI Assembly Concern Item Solution 1. Fix the cable at the binding core by this way 2. Add one spring 3. Add one spring 72 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Item 4. Solution Add two gasket gasket gasket 5. Add one gasket gasket 73 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 Disassembly/Assembly Disassembly SOP PJ513D Dismantle SOP Step Description Parts cap lens 1 take off the cap lens 2 disassembly the screw*2, and take off the lamp door, disassembly the screw*1 and lamp wire, take off the lamp module. cap lens Lamp wire screw*3, lamp door, lamp wire, lamp module 1 2 screw*4 1 3 3 disassembly the screw*4 4 2 4 take off the upper case module upper case module upper case 74 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 5 take off the upper case mylar, left and right case module from upper case mylar right case 6 7 8 disassembly the screw*4,take off the Speaker wire and rear case left case Speaker wire 3 1 2 disassembly the double fan, and take off the double fan wire disassembly the screw*5, and take off the M/B shielding upper case mylar, left and right case module 4 rear case Double fan Wire 4 double fan, double fan wire 1 5 screw*5, M/B shielding 2 3 75 ViewSonic Corporation screw*4, Speaker wire, rear case Confidential - Do Not Copy PJ513D-1 Wire saddle 1 Wire saddle 2 9 take off the C/W FPC wire, blower fan wire, C/W sensor wire, Ballast 5-Pin wire, IR wire, wire saddle*2 C/W sensor wire C/W FPC wire IR wire Blower fan wire Ballast 5-Pin wire C/W FPC wire, blower fan wire, C/W sensor wire, Ballast 5-Pin wire, IR wire, wire saddle*2 10 take off the M/B M/B disassembly the screw*4, disassembly the 11 grounding screw*1 and take off the Power B/D SHD screw*5, Power B/D SHD 76 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 disassembly the wire*2 and 12 screw*2, take off the power BD and ballast Mylar wire*2 screw*2, power BD, ballast Mylar 1 disassembly the screw*4, take off 13 the lamp box and the blower fan 4 2 screw*4, lamp box, blower fan 3 disassembly the screw*3, take off 14 the OPT eng and IR wire. 1 2 screw*3, OPT eng, IR wire 3 15 take the Front case module Front case module 77 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 take off the Front case mylar, IR Sensor and IR 16 Sensor wire module from Front case IR Sensor Front case mylar, IR Sensor, IR Sensor wire Mylar IR Sensor wire 1 disassembly the 17 screw*3 and the ballast BD, wire*3 take off the push button and the adjust foot, 18 disassembly the screw*6 and clip*3, the left is lower case 2 screw*3, ballast BD, wire*3 3 Adjust foot push button, adjust foot, screw*6, clip*3, lower case Push button take off the sponge, 19 disassembly the screw*2 and DMD HSINK sponge, screw*2, DMD HSINK 78 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 disassembly the screw*2,take off the CW shielding, 20 disassembly the screw*1 and take off the CW module screw*3, CW shielding, CW module CW module Focus ring 21 Remove FOCUS ring FOCUS ring disassembly the 22 screw*3, take off the PL ass'y screw*3, PL ass'y 79 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 disassembly the screw*4, and take 23 off the Chip BD module , take off the Baffle DMD screw*4, Chip BD, Baffle DMD rotate the screw, take off the DMD 24 IC, take off the Thermal PAD DMD IC, Thermal PAD disassembly ILL MODULE( screw*2 25 ),sponge, ASPH lens ILL MODULE, screw*2, sponge, ASPH lens 80 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 disassembly the front clip and upper clip, then take off the LP module, adjust screw*2 upper clip 26 front clip, upper clip, LP module, adjust screw*2 disassembly HSG 27 baffle and screw*1 from HSG HSG baffle, screw*1 front clip 81 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 6. Troubleshooting Flow Chart 1. System Trouble Shooting Flow Chart System Trouble Shooting Flow Chart No LED On? Yes If Power On, Lamp On? No 1. 2. 3. 4. 5. Check power code Check lamp door. Check Download SW. Check DC Voltage 1.2V 1.8V 2.5V 3.3Von Main board Check power board and 14-pin power connector. 1. 2. 3. 4. 5. 6. Check Main BD to Ballast signal wire. Check thermal switch and wire Check color wheel. Check DC Voltage 12V on Main board Check Ballast. Check Power Board. 1. 2. 3. Check Input Cable Check OSD Source set up Check Main board 1. 2. 3. 4. 5. Check OSD Lamp Hours Check Lamp Door Check Lamp still light or not? Check Fan still spin or not? Check Thermal status 1. 2. 3. 4. Check Remote module battery Check Remote module Check IR Receiver on Main board Check IR Receiver on Input board 1. 2. 3. Check DMD Chip Check DMD Chip board Check Main board Yes Yes No Signal? No Yes Power Auto Turn Off No Yes IR Remote Control NG? No Yes Pixel Fail? A 82 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 A No Image NG? (Raindrops) Yes 1. 2. 3. 4. Check color wheel and Sensor board Check DMD Chip and holder Check Main BD XDRAM Check Main BD DDP2230 Yes 1. 2. 3. 4. Check Main board Check color wheel and sensor board Check DMD Chip board Check DMD Chip and socket Yes 1. 2. 3. Check color wheel and sensor board Check Main board Check DMD Chip board 1. 2. Check Main board Check DMD Chip board Yes 1. 2. 3. Check color wheel Check sensor board color index signal Check main board Yes 1. 2. 3. Check DMD Chip holder Check DMD Chip board Check Main board 1. Check Main BD output to DMD Chip BD Resistance soldering Check Main BD output to DMD Chip BD capacitor soldering No Image NG? (Blank) No Image NG? (Screen flashing) No Image NG? (Screen Dim-mish) Yes No Image NG? (Freezing) No Image NG? (Missing column bar) No Image NG? (Screen overlap) 2. Yes 83 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 2. Error Message Power Temp Lamp Status Note O - - Stand-by G - - Powering up G - - Normal operation O - - Normal power-down cooling O - - First Lamp-Lit error cooling Lamp Error Messages O - R Second Lamp-Lit error - - R Lamp error in normal operation Thermal Error Messages - R - Fan 1 error (the actual fan speed is ±20% outside the desired speed.) Lamp Fan - R R Fan 2 error (the actual fan speed is ±20% outside the desired speed.) Ballast Fan - R G Fan 3 error (the actual fan speed is ±20% outside the desired speed.) Blower Fan R R R Thermal Sensor 1 open error (the remote diode has an open-circuit condition.) DMD sensor R R G Thermal Sensor 2 open error (the remote diode has an open-circuit condition.) G R R Thermal Sensor 1 short error (the remote diode has an short-circuit condition.) G R G Thermal Sensor 2 short error (the remote diode has an short-circuit condition.) O R R Temperature 1 error (over limited temperature) O R G Temperature 2 error (over limited temperature) - G R Fan IC #1 I2C Connection error DMD sensor GMT 793 84 ViewSonic Corporation DMD sensor Confidential - Do Not Copy PJ513D-1 3. Power Trouble Shooting Guide Power BD Check. Fuse Broken ? Proceed to “check DC-DC OUTPUT" No Yes Proceed to "Primary Circuit Check". No DC-DC Output. B+=385VDC ? No Proceed to " Primary Circuit Check" Yes TOPSwitch Broken ? No Lacks of some componets around TOPSitch ? Yes Yes Replace new TOPSwitch solder them. No 85 ViewSonic Corporation Confidential - Do Not Copy Check Trace. PJ513D-1 Check primary circuit. Fuse Broken ? Proceed to "Check IC601". No Yes Check Q601 damages ? Check BD601 damages ? No Yes Yes PinD & PinS of Q601 are shorted. Replace new MOSFET. Inside diodes of BD601 are shorted. Replace new bridge diode. No Proceed to "Check IC601". Check IC601. Check Pin8 if shorted to GND. Output Pin shorted to GND ? (Pin8) No Check 15VPFC Votage. Yes Replace with new IC L6561D and D611, D612, and D613 86 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 4. Optical & Optical Engine Trouble Shooting Guide 4-1 Optical Trouble Shooting Guide No. Item Trouble Shooting Guide 1 Brightness 1. Change lamp 2 Uniformity 1. Change lamp FOFO Contrast 1. 2. 3. 4. 5. 4 ANSI Contrast 1. Clean PL 2. Clean DMD 3. Change PL 5 Color 1. Check color wheel delay 2. Check CW 50% point. Replace CW if necessary 6 Color Uniformity 1. Change lamp Blue Edge 1. Refer to Item#2-1 (attached below) 2. Change CM 3. Change SUB HSG 8 Blue/Purple Border 1. Refer to Item#2-1(attached below) 2. Change CM 3. Change SUB HSG 9 Focus 1. Change Projection Lens 2. Check PL datum and DMD parallel 10 Dust Clean DMD 11 Horizontal/Vertical Strips 1. 2. 3. 4. 5. 12 Pixel Fail Change new DMD 3 7 Check ADC calibration Check user’s menu brightness & contrast are default Clean DMD Clean PL Check ILL stop assy Check connector between chipBD and MainBD Re-install DMD with chipBD Check if any pin of C-Spring is missing, damaged or dirty Change new ChipBD/C-Spring Change new DMD 87 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 4-2 Engine Assembly Trouble Shooting Guide S ta rt P ower O n 1 .c h k C W 2 .c h k D M D C h ip /b 3 .c h k M a in /b NG OK Im a g e Q u a lity NG D ust 1 .c le a n D M D c h ip 2 .c le a n C /M Yes No 1 .c h k le n s h o u s in g / D M D h o u s in g A s s e m b ly 2 .c h k lig h t p ip e a s s e m b ly 3 .c h k C /M a s s e m b ly 4 ,c h a n g e lig h t p ip e c lip 5 .c h a n g e lig h t p ip e B lu e E d g e Yes No Focus N G OK Y es c h a n g e p ro je c tio n le n s No P ix e l F a ilu re EE P e rfo rm a n c e NG S y s te m T ro u b le s h o o tin g G u id e No lig h t le a k a g e OK O p tic a l P e rfo rm a n c e 1 .c h a n g e D M D 2 .c h a n g e D M D /b 3 .c le a n e la s to m e r Y es Yes 1 .c h k D M D b a ffle 2 .c h k C /M Or check DMD chip socket NG B rig h tn e s s Y es 1 .R e s e t F a c to ry m o d e , c h k D C o ffs e t/G a in s e tu p 2 .c h k D M D c h ip /b 3 .c le a n p ro je c tio n le n s 4 .c le a n C /M 5 .c le a n o p tic a l p a rts No U n ifo rm ity 1 .c h k C /M 2 .c h k p ro je c tio n le n s Y es No 1 .R e s e t F a c to ry m o d e , c h k D C o ffs e t/G a in s e tu p 2 .c h k D M D b a ffle 3 .c h a n g e p ro je c tio n le n s Y es C o n tra s t No 1 .R e s e t F a c to ry m o d e , c h k C W d e la y 2 .c h a n g e C W 3 .c h a n g e p ro je c tio n le n s Y es C o lo r 1 .c h k C /M 2 .c h k D M D No C o lo r U n ifo rm ity Y es 88 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 4-3 “Blue Edge” Trouble Shooting: I. Re-adjust “Overfill” first. For Overfill Re-adjustment: i. Those 2 Adjustment Screws must be released for around 2 mm first. ii. Alignment Sequence: a.To adjust “Horizontal Adjustment Screw” firstly, then “Vertical Adjustment Screw¡¨. b. Refer to Figure 1-1.. (2) Overfill Vertical Adjustment Screw (1) Overfill Horizontal Adjustment Screw Fig. 1-1 II. Re-assemble LP module—include LP, LP Baffle, LP clip. 89 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 7. Block Diagram Hardware Architecture The Projector consists of the Source board, Main board, Keypad board, Fan board, EMI board, PFC board, Ballast board, Door interlock switch, Color wheel index sensor board, and the Thermal break sensor board. Please see Figure 1. Source Board consists of audio phone jack, video RCA jack, S-video mini-DIN head, and USB head. Main Board consists of RGB A/D conversion, Video decoder, DLP ASIC, Flash and RAM, Motor driver, DMD Reset driver DAD2000, and IR receiver. Keypad Board consists of 8 keypads and 3 twice-color LEDs. Fan Board consists of DC/DC converter, Thermal Break circuit, Blower Fan driver circuit, Rear Fan driver circuit, and the temperature sensing circuit. Power supply circuit consists of AC line EMI filter, Power Factor Correction circuit. Ballast Board consists of Lamp synchronization circuit, Lamp lit feedback circuit, and Lamp power control circuit. Hardware Architecture Keypad Circuit Main Operation Circuit (DLP Image Processor DDP2230) (Video decoder TVP5147) (DMD Reset driver DAD2000) (A/D 9883) (RAMBUS XDRAM) Thermal break sensor Circuit Fan Driver Circuit Input Source Circuit From AC socket Ballast Module CW Lamp Index Door sensor switch Door interlock switch EMI PFC Circuit Filter 90 ViewSonic Corporation To Lamp Confidential - Do Not Copy PJ513D-1 8. Schematic Diagrams 6,7,9,11,17 6,7,9,11,17 PC-RIN PC-GIN PC-BIN HSYNC_I VSYNC_I SDA SCL PC-RIN PC-GIN PC-BIN PC-RIN PC-GIN PC-BIN HSYNC _I VSYNC_I HSYNC_I VSYNC_I P3P3V P5V P3P3V P5V P3P3V GRE[7:0] GRE[7:0] GGE[7:0] GGE[7:0] GBE[7:0] GBE[7:0] AD_CLK AD_HS AD_VS AD_CLK AD_HS AD_VS P5V V33 P3P3V AD_SOG AD_CLAMP AD_COAST AD_SOG AD_CLAMP AD_COAST SDA SCL AD_SOG AD_CLAMP AD_COAST GRE[7:0] GGE[7:0] GBE[7:0] AD_CLK AD_HS AD_VS POSENSE POSENSE POSENSE MTR_ARSTZ PMD_INTZ SSP0CSZ2 PWRGOOD V33 GND SSP0_CLK 05_ADC 05_ADC P5V HSYNC _I VSYNC_I SSP0_RXD SSP0_TXD HSYNC_I VSYNC_I PWR_DOWN POSENSE MTR_ARSTZ PMD_INTZ SSP0_CSZ2 PWRGOOD A1P2V P1P2V A1P2V P1P2V A1P8V P1P8V A1P8V P1P8V P2P5V P2P5V P3P3V P3P3V P5V P5V P12V P12V SSP0_CLK SSP0_RXD SSP0_TXD GND 11_PMD1000 11_PMD1000 GND 01_D-SUB_I/O 01_D-SUB_I/O SSP0_CLK P1P8V P1P8V VD_CLK P2P5V P2P5V VD_YUV[9:0] P3P3V P3P3V VD_CLK VD_YUV[9:0] VD_CLK VD_YUV[9:0] SDA SCL SDA SCL 6,9,14,15 EXT_ARSTZ GND A1P2V P1P2V A1P2VIO POSENSE MTR_ARSTZ PMD_INTZ SSP0_CSZ2 PWRGOOD V33 V33 CVBS POSENSE MTR_ARSTZ PMD_INTZ SSP0_CSZ2 PWRGOOD PWRGOOD EXT_ARSTZ CVBS SSP0_CLK SSP0_CLK SSP0_RXD SSP0_TXD SSP0_CSZ0 EXT_ARSTZ SSP0_RXD SSP0_TXD SSP0_CSZ0 EXT_ARSTZ SSP0_RXD SSP0_TXD SSP0_CSZ0 EXT_ARSTZ 6,9,14,15 EXT_ARSTZ CVBS CHROMA LUMA PWRGOOD CHROMA LUMA AUDIO_MUT AUDIO_VOL AUDIO_SW P1P8V P3P3V P3P3V GND SSP0_CLK P3P3V P3P3VS P5V P3P3V P3P3VS P5V GND USB_D+ USB_DUART0_CTSZ UART0_RXD UART0_RTSZ UART0_TXD AUDIO_MUT AUDIO_VOL AUDIO_SW AUDIO_MUT AUDIO_VOL AUDIO_SW VCC2 VCC2 P3P3V P3P3V IRRCVR LAMPLIT LAMP_RXD LAMPEN P3P3VS 6,7,9,11,17 6,7,9,11,17 12_DAD1000 12_DAD1000 SSP0_CSZ1 EXT_ARSTZ SSP0_CSZ1 PWM_AUDIO1 PWM_AUDIO2 PWM_AUDIO3 USB_D+ USB_D- USB_D+ USB_D- UART0_CTSZ UART0_RXD UART0_RTSZ UART0_TXD UART0_CTSZ UART0_RXD UART0_RTSZ UART0_TXD P3P3VS P5VS P5V P5VS P5V P12V P12V FAN2_B FAN2_E PWR_DOWN PWR_DOWN IRRC VR IRRC VR LAMPLIT LAMP_RXD LAMPEN LAMPLIT LAMP_RXD LAMPEN FAN_SW FAN_SW SDA SCL SDA SCL FAN2_B FAN2_E P3P3V FAN2_B FAN2_E P5V P12V GND MBRST[15:0] VCC2 UART0_CTSZ UART0_RXD UART0_RTSZ UART0_TXD XDR_RQ_CTMP XDR_RQ_CTMN XDR_RQ_CTMP XDR_RQ_CTMN SDA SCL SDA SCL 6,7,9,11,17 6,7,9,11,17 6,7,9,11,17 6,7,9,11,17 SDA SCL OCLKA PWR_DOWN P3P3V GND SDA SCL OCLKA A1P8V A1P8V P2P5V P2P5V P3P3V P3P3V XDR_RQ_CTMPA1P2VIO XDR_RQ_CTMN P1P8V A1P2VIO P1P8V GND 10_XDRAM 10_XDRAM GND 09_CLOCK 09_CLOCK IRRCVR LAMPLIT LAMP_RXD LAMPEN FAN_SW P3P3V EXT_ARSTZ SSP0_CSZ1 13_DMD_INTERFACE 13_DMD_INTERFACE USB_D+ USB_D- OCLKA CW_PWM CWINDEXA CW_PWM CWINDEXA OCLKA CW_PWM CWINDEXA P12V P12V P5V P5V P3P3V P3P3V P3P3V GND P5V P3P3VS P3P3V P12V GND P5VS P5V 15_FAN 15_FAN 03_POWER 03_POWER VCC2 P12V SSP0_CSZ1 02_INPUT 02_INPUT PWR_DOWN MBRST[15:0] MBRST[15:0] SSP0_RXD SSP0_TXD SSP0_CSZ0 EXT_ARSTZ GND PWM_AUDIO1 PWM_AUDIO2 PWM_AUDIO3 PWM_AUDIO1 PWM_AUDIO2 PWM_AUDIO3 A1P2V P1P2V A1P2VIO P1P8V P12V 04_DECODER 04_DECODER SSP0_RXD SSP0_TXD 08_DDP2230_PWR_DEBUG 08_DDP2230_PWR_DEBUG SSP0_CLK CHROMA LUMA P3P3V 06_MEMORY_IN 06_MEMORY_IN GND 6,7,9,11,17 6,7,9,11,17 P3P3V SSP0_CLK SSP0_RXD SSP0_TXD P3P3VS P3P3V 14_CWMOTOR 14_CWMOTOR P5VS P5V GND 07_DDP2230_ARM_CONTROL 07_DDP2230_ARM_CONTROL ViewSonic Corporation Model Title ViewSonic Corporation Date 91 Confidential - Do Not Copy PJ513D-1 MAIN BOARD Rev: P5V K K 4,5,6,7,9,13,16,17 P5V DN2 J PC-RIN_B J BAV99 D1 K A BAV99 PC-GIN_B LL4148 A PC-BIN_B A A BAV99 TP10 13 14 15 TP8 A D4 A D5 P5V PC-RIN_B LC1 Z80 PC-RIN PC-RIN 7 PC-GIN_B LC2 Z80 PC-GIN PC-GIN 7 PC-BIN_B LC3 Z80 PC-BIN PC-BIN 7 K LL4148 K LL4148 DDCP5V G2 PC_VSYNC PC _HSYNC GSDA PC_VSYNC PC_HSYNC GSDA PC_VSYNC D10 A TZMC6V2 UB1 16 RB1 GOUT 15 RB2 BOUT 14 RB3 REF VCC 13 5 VEE EN 12 6 GND VCC 11 7 VEEOUT PD 10 PC-GIN_B 2 PC-BIN_B 3 BIN 4 CB10 0.1U K 10 CB2 8 0.1U K RIN GIN DGND U1 4 R3 1K J VSYNC_I 7,8 HSYNC_I 7,8 R4 2K J 74AHCT1G14GV 1 A0 VCC 8 CA1 2 A1 WP 7 0.1U K 3 A2 SCL 6 4 GND SDA 5 DDCP5V DDCP5V P5V R5 4.7K J R6 4.7K J R7 4.7K J GSCL GSDA PC_HSYNC PC _HSYNC R8 47 J CH1 150P J C2 0.1U K U3 2 4 R9 1K J R10 2K J 74AHCT1G14GV 75 J ROUT 1 4,5,6,7,9,13,16,17 C1 0.1U K U2 AT24C02N-10SU-1.8 PC-RIN_B 47 J R1 4.7K J 2 CV1 470P K RGB D-sub input ciriuit RB4 PC_VSYNC R2 GSCL K K D9 A TZMC6V2 A TZMC6V2 D8 A TZMC6V2 A TZMC6V2 2,13,14,15,16,17 GND K K K GSCL D7 P5V DDCP5V 2K20072A15 D6 P5V 5 TP9 TP5 TP7 3 1 12 A LL4148 DVCC 75 J 75 J RGBO_R RGBO_G P3P3V RGBO_B P3P3V CB1 P3P3V 0.1U K C3 0.1U K U4 5 TP6 RED-GND0 PC-RIN-B GREEN-GND0 PC-GIN-B BLUE-GND0 PC-BIN-B PC-5VIN0 A LL4148 4 CB3 9 0.1U K ISL59837IAZ-T13 R11 47 J 2 PWR_DOWN PW R_DOWN 9 74AHC1G14GV GND 4,5,6,7,8,9,10,11,12,13,14,15,16,17 1 3 6 1 7 2 8 3 9 4 10 5 11 K TP3 J1 TP4 D3 TP1 G1 TP2 K D2 5 J 3 1 K DN1 DN3 P5V P5V 4,5,6,7,9,13,16,17 R12 2K J C PWR_DOWN_A 14 H SYNC_O 13 270 J 5 10 4 9 3 8 2 7 1 6 UB3 74HCT1G125GW 12 K P5V DB5 G1 CB5 0.1U K 5 PWR_DOWN_A 1 11 JB1 PC _HSYNC RB8 47 J 2 4 RB9 K PC_HSYNC A TZMC6V2 270 J DB4 TPB1 TPB4 TPB5 RGBO_B TPB6 RGBO_G RGBO_R P5V DB1 J BAV99 DB2 J BAV99 DB3 J BAV99 P5V RGBO_R 4,5,6,7,9,13,16,17 D11 LL4148 A A A A TZMC6V2 A 3 ViewSonic Corporation 1.2K RGBO_G P5V RB22 UB4 74HCT1G125GW RGBO_B K 15 VSYNC_O K RB7 E G2 TPB3 4.7K J RB5 K 4 2K20072015 RB21 1.2K TPB2 B K 2 47 J QC1 2N3904S 3 PC_VSYNC PC_VSYNC RB6 CB4 0.1U K 5 1 P5V RGB D-sub output ciriuit 92 Confidential - Do Not Copy PJ513D-1 DN4 P3P3V TP15 U6 4 AUDIO AUDIO_A 2 L2 Z42 CHROMA 4 CHROMA 9 6 AUDIO_SW S1 S2 1 IN TP16 ADG779 2 MODE 3 SVR 4 IN OUT+ 8 GND 7 Vp 6 OUT- 5 SPEAK+ P5V C4 CC4 CC5 CC12 CC13 0.1U K 22U M 22U M 22U M 22U M SPEAK- RA1 SPEAK- OPEN J2 G1 1 2 G2 3,5,6,7,9,13,16,17 RC8 5.9K F SPEAK+ SPEAK- 470 470 C VOL 2KD2094102 9 AUDIO_VOL RC9 1 K K 3,5,6,7,8,9,10,11,12,13,14,15,16,17 AUDIO_MUT RC10 RC11 1K J QC4 2N3904S B ZD8 TZMC6V2 A Video input RB10 1K J RC12 1K J A ZD6 TZMC6V2 9 B 220 J MUT QC3 2N3904S C TP18 TZMC6V2 ZD7 K K TZMC6V2 ZD5 QC2 2N3904S B 220 J RC13 150 C BAV99 A RC7 RC6 5.9K F 3,5,6,7,9,13,16,17 P5V C 6 RC5 QC5 2N3904S B E CVBS P5V TP11 TP12 TP13 E CVBS A Z42 P5V GND Z42 RC14 1K J RC15 150 E BAV99 A L3 J DN6 K SPEAK+ LC4 TDA8551T P5V COMPOSIT1 2 UP/DOWN A DN5 2 22U M CC3 0.33U Z RC4 4.7K J TP17 1 CC2 22 RC3 5 1 E K P5V P5V U5 CC11 22U M Dout 6 CC1 0.1U K 22 2 Z42 G2 MUTRC2 MUT VDD 1 6 GND L1 LUMA 3 G5 C LUMA 3 G5 G3 . 2B10190051 470 J G2 J4 RC1 J Y . G3 VOL VOL G4 G1 2B14016041 BAV99 A K P5V G4 G1 TP14 J3 Audio circuit TP29TP30 USB_DUSB_D+ TPC1 TPC2 J5 P3P3V 1 2 TPC3 LC5 Z80 3 LC6 Z80 TP34 AUDIO CC6 0.1U K CC7 CC8 0.1U K 47P J 50V A 2B10254071 AUDIO RA2 RA3 OPEN 4.7K J TZMC6V2 ZD3 AUDIO_A CA2 PWM_AUDIO1 0.1U K R186 0 J RA5 PWM_AUDIO2 OPEN R187 0 J ZD4 TZMC6V2 PWM_AUDIO1 9 PWM_AUDIO2 9 PWM_AUDIO3 9 A RA7 OPEN Audio input terminal TP23 V+ 6 7 K J 2 TP178 LC10 Z80 CTSZ_A UC1 BAV99 A A 3 V+ G1 G3 C1_A 232VRX.DL 3 5,9 P3P3VS 1 5 1 RTSZ_A 5 G1 G3 4 Z80 G2 2 LC9 G2 4 TP177 CTSZ V+ J BAV99 6 8 7 J7 BAV99 232V- RTSZ DN8 P3P3VS A BAV99 A DN7 J 8 J DN14 K K K TP24 DN13 RX.DL 232VRTSZ 2B14015001 TP25 C2_A CR2 0.1U K C1_B CR3 0.1U K C2_B 232VCR4 CTSZ CR5 RTSZ CTSZ 1 2 3 4 5 6 7 8 C1+ V+ C1C2+ C2VT2OUT R2IN VCC GND T1OUT R1IN R1OUT T1IN T2IN R2OUT 16 15 14 13 12 11 10 9 CR1 10U Z TX.DL RX.DL TX.DL RX.DL UART0_RXD 9 UART0_TXD 9 UART0_RTSZ 9 UART0_CTSZ 9 ICL3232ECBNZ RX.DL_A LC7 Z80 TX.DL_A LC8 Z80 0.1U K 0.1U K TX.DL CC9 100P K TX.DL CC10 100P K 3,5,6,7,8,9,10,11,12,13,14,15,16,17 GND ViewSonic Corporation RS232 circuit 93 Confidential - Do Not Copy PJ513D-1 3,6,7,8,9,10,11,1 RA6 1.8K PWM_AUDIO3 ZD2 TZMC6V2 A RA4 4.7K J P3P3V AUDIO_A TZMC6V2 ZD1 K K A A USB input 9 9 D13 TZMC6V2 D12 2BC0010031 USB_DUSB_D+ K K VCC DATADATA+ GND GND A 1 2 3 4 5 K K J9 TZMC6V2 G2 CASE CASE G1 These parts of this portion should be connected closely. FAN2_E 17 FAN2_B P12V TP45 L14 13,14,16,17 P12V C172 4.7U M C173 22U 25V TP47 TP179P12V_IN TP180 Z30 Z30 Z30 L15 C171 0.1U Z 17 L16 L17 L18 L19 J10 1 3 5 TP181 7 Z30 TP182 9 Z30 11 Z30 13 1 3 5 7 9 11 13 TP46 TP48 2 4 6 8 10 12 14 2 4 6 8 10 12 14 GND TP183 R203 PWR_DOWN 9 2K71072207 TP49 3,4,6,7,8,9,10,11,12,13,14,15,16,17 R184 TP50 P5VS 0 1M C175 C174 22U 25V C176 4.7U M 0.1U Z POWER FROM DC/DC BOARD 3,4,6,7,9,13,16,17 P5VS 9 L4 G2 5 4 3 2 1 G1 G2 5 4 3 2 1 G1 TP19 TP20 TP21 TP22 3 P5VS VIN Z120 C177 R14 100 R15 TP80 270 J LAMPLIT 2 OUT 4 P3P3VS G960T63UF C178 100U 16V <Spec> 4,9 C179 + 10U Z 9 C 2KL2021005 0.1U Z LAMP_RXD 9 VOUT 1 J6 P3P3VS U17 1 P5V 2 10K J GND P5V R13 Q1 B RA8 2K LAMPEN 9 E 2N3904S 3,4,6,7,8,9,10,11,12,13,14,15,16,17 GND Lamp circuit 3.3V POWER P5VS P5VS R16 10K J TP26 J8 TP27 G1 1 2 3 G2 G1 1 2 3 G2 TP28 L5 P3P3VS Z120 2KL2021003 5 U8 TSOP14838 I R1 U7 1 4 VCC GND VOUT R18 IR circuit ViewSonic Corporation 94 Confidential - Do Not Copy PJ513D-1 TP32 IRV CC 100 J C5 0.1U K C6 4.7U Z R17 10K J 3 2 1 TP31 P5VS 2 I R2 3 P5VS R19 510 J TP33 74AHC1G08GW IRRCVR 9 P1P8V V33_A V33 V33 7 C16 0.1U K SCL SDA SCL SDA EXT_ARSTZ EXT_ARSTZ R22 10K J TP35 TP36 TP37 TP38 R24 R25 R26 C18 27P J Y1 RB11 100K 7 8 9 VI_2_A VI_2_B VI_2_C 16 17 18 VI_3_A VI_3_B VI_3_C 23 VI_4_A 28 29 SCL SDA 33 34 35 36 37 PWDN RESETB GPIO AVID/GPIO GLCO/I2CA 71 72 73 FID/GPIO HS/CS/GPIO VS/VBLK/GPIO 74 75 14.31818MHZ 4.7K J10K J 2.2K 39 49 62 38 48 61 IOGND39 IOGND49 IOGND62 IOVDD38 IOVDD48 IOVDD61 TVP5147PFP C_0/GPIO0 C_1/GPIO1 C_2/GPIO2 C_3/GPIO3 C_4/GPIO4 C_5/GPIO5 C_6/GPIO6 C_7/GPIO7 C_8/GPIO8 C_9/GPIO9 70 69 66 65 64 63 60 59 58 57 DATACLK INTREQ 77 76 12 13 C19 27P J 3,4,5,7,8,9,10,11,12,13,14,15,16,17 GND XTAL1 XTAL2 CH1_A33VDD CH2_A33VDD CH1_A33GND CH2_A33GND AGND 0.1U K VI_1_A VI_1_B VI_1_C NC14 NC15 NC19 NC20 NC21 NC22 P1P8V V33_A L7 Z120 V33 C20 0.1U K VD_YUV0 VD_YUV1 VD_YUV2 VD_YUV3 VD_YUV4 VD_YUV5 VD_YUV6 VD_YUV7 VD_YUV8 VD_YUV9 R20 R21 Z120 V33 V33_A C32 0.1U K C33 0.1U K C34 0.1U K C35 0.1U K C36 0.1U K C37 0.1U K C38 0.1U K 4.7K J 4.7K J Analog VDD 3.3V 40 VCLK_A 30 14 15 19 20 21 22 R23 47 J C17 10P J VCLK VD_CLK 8 P1P8V P2P5V V33 P2P5V 11,13 U10 1 C22 10U Z VIN C30 0.1U K 16V P1P8V AME8815AEGT180Z VOUT 3 GND TAB 9 C13 80 1 2 54 53 52 51 50 47 46 45 44 43 L6 C21 22U K 2 G1 9 7,9,11,17 CVBS_I 0.1U K C11 C10 0.1U K Cb_I_A CHROMA_A 0.1U K C9 Y_I_A LUMA_A 0.1U K C12 Cr_I_A 0.1U K 0.1U K C14 C15 CVBS_A P3P3V 3,7,8,9,10,11,13,14,15,16,17 P3P3V Y0 Y1 Y2 Y3 Y4 Y5 Y6 Y7 Y8 Y9 DVDD41 DVDD55 DVDD67 DVDD31 DGND27 DGND32 DGND42 DGND56 DGND68 CVBS_I LUMA_I C7 0.1U K 0.1U K C8 VD_YUV[9:0] 8 41 55 67 31 27 32 42 56 68 LUMA_I CHROMA_I PLL_A18GND PLL_A18VDD A18VDD_REF A18GND_REF CHROMA_I CH1_A18GND CH2_A18GND A18GND CH1_A18VDD CH2_A18VDD A18VDD D 4 5 3 6 26 79 10 24 78 11 25 VD_YUV[9:0] C23 0.1U K C24 0.22U K C25 0.1U K VTERM P1P8V P1P8V C39 0.1U K C43 C44 L9 CVBS 5.6P C C45 1.8U K L10 CVBS CVBS_I C46 220P J C47 220P J 4 CVBS_I LUMA L11 LUMA_I C48 220P J R27 75 J P1P8V 1.8U K C49 220P J 4 LUMA_I CHROMA 1.8U K CHROMA CHROMA_I C50 220P J R28 75 J C41 0.1U K C42 0.1U K 5.6P C 5.6P C LUMA C40 0.1U K C51 220P J R29 75 J CHROMA_I C26 22U K VTERM L8 Z120 C27 0.1U K C31 C28 0.1U K 0.1U K 2.5V TO 1.8V ViewSonic Corporation 95 Confidential - Do Not Copy PJ513D-1 10,12,13 C29 0.1U K PVDD C52 OPEN C53 OPEN R37 3 SOGIN PC-GIN 1.5K R30 OPEN SOGIN C69 10P J V33 L12 AVDD 6 GVMID 3 3 8 8 VSYNC_I HSYNC _I AD_COAST AD_CLAMP VSYNC_I HSYNC_I AD_COAST AD_CLAMP V33 C54 C55 C56 C57 C58 P3P3V C59 C60 Z120 AVDD 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z V33 0.1U Z C61 0.1U K PC-BIN PC-BIN R31 47 J GBIN_A C63 AVDD AVDD 3 PC-GIN PC-GIN R32 10P J C64 47 J GGIN_A CA3 1000P K 50V C65 SOGIN 0.047U K GGIN AVDD AVDD 3 PC-RIN 9 6,9,11,17 SCL SDA PC-RIN R33 47 J GRIN_A C66 0.047U K GRIN 10P J C67 SCL SDA GVREF AVDD R34 R35 R36 75 J 75 J 75 J AVDD C68 0.1U K GND U11 MST9883C-LF-110 GBE[7:0] 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 GND B/Cb[0] B/Cb[1] B/Cb[2] B/Cb[3] B/Cb[4] B/Cb[5] B/Cb[6] B/Cb[7] VDD GND G/Y[0] G/Y[1] G/Y[2] G/Y[3] G/Y[4] G/Y[5] G/Y[6] G/Y[7] GND GB0 GB1 GB2 GB3 GB4 GB5 GB6 GB7 GBE0 GBE1 GBE2 GBE3 GBE4 GBE5 GBE6 GBE7 GG0 GG1 GG2 GG3 GG4 GG5 GG6 GG7 GGE0 GGE1 GGE2 GGE3 GGE4 GGE5 GGE6 GGE7 V33 GGE[7:0] 3,4,5,6,8,9,10,11,12,13,14,15,16,17 GRE[7:0] AVDD V33 V33 AVDD GR0 GRE0 GRE1 GRE2 GRE3 GRE4 GRE5 GRE6 GRE7 GR1 GR2 GR3 GR4 GR5 GR6 GR7 GCL_K GFB_K GH_S GV_V R38 R39 R40 R41 47 47 47 47 J J J J AD_CLK AD_HS AD_SOG AD_VS C70 10P J PVDD P3P3V AVDD P5V U12 3,4,5,6,9,13,16,17 P5V 3 Z120 C71 C74 C75 C76 C77 C78 C79 C80 C81 0.1U Z 0.1U Z ViewSonic Corporation 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 96 Confidential - Do Not Copy PJ513D-1 VIN VOUT 2 OUT 4 1 3,6,8,9,10,11,13,14,15,16,17 P3P3V GND L13 C73 GBE[7:0] 8 GGE[7:0] 8 GRE[7:0] 8 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 3 AVDD AVDD 0.047U K GBIN GND AVDD BIN/Pb GND AVDD AVDD GND GIN/Y SOGIN GND AVDD AVDD GND RIN/Pr A0 SCL SDA VREF AVDD GND GND AVDD GND VSOUT SOGOUT HSOUT DCK GND VDD R/Cr[7] R/Cr[6] R/Cr[5] R/Cr[4] R/Cr[3] R/Cr[2] R/Cr[1] R/Cr[0] VDD VDD GND 10P J C62 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 GND AVDD CLAMP MIDSCV GND PVDD PVDD FILT GND VSYNC HSYNC COAST GND PVVD PVDD GND GND VDD VDD GND 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 PVDD G960T63UF C82 C72 10U Z C83 10U Z C84 C85 0.1U Z 0.1U Z 0.1U Z AD_CLK AD_HS AD_SOG AD_VS 8 8 8 8 U13A U13C DDP2230 PMDAT_[15:0] PMDAT15 PMDAT14 PMDAT13 PMDAT12 PMDAT11 PMDAT10 PMDAT9 PMDAT8 PMDAT7 PMDAT6 PMDAT5 PMDAT4 PMDAT3 PMDAT2 PMDAT1 PMDAT0 P30 R27 R28 R29 R30 T30 T29 T28 T27 U30 U28 U27 U26 V30 V29 V28 GPIO_34 GPIO_33 GPIO_32 PMADR20 PMADR19 PMADR18 PMADR17 PMADR16 PMADR15 PMADR14 PMADR13 PMADR12 PMADR11 PMADR10 PMADR09 PMADR08 PMADR07 PMADR06 PMADR05 PMADR04 PMADR03 PMADR02 PMADR01 PMADR00 H28 H27 H29 J28 H30 J29 J30 K27 J27 K28 K30 K29 L27 L28 L30 M27 M28 M29 M30 N27 N28 N29 N30 P26 PMDAT_[15:0] PMDAT_15 PMDAT_14 PMDAT_13 PMDAT_12 PMDAT_11 PMDAT_10 PMDAT_9 PMDAT_8 PMDAT_7 PMDAT_6 PMDAT_5 PMDAT_4 PMDAT_3 PMDAT_2 PMDAT_1 PMDAT_0 DDP2230 VCC PM_BLSZ_1 PM_BLSZ_0 SDRAM_DQM_1 SDRAM_DQM_0 SDRAM_RASZ SDRAM_CASZ SDRAM_CLK SDRAM_CKE PMADR_22 PMADR_21 PMADR_20 PMADR_19 PMADR_18 PMADR_17 PMADR_16 PMADR_15 PMADR_14 PMADR_13 PMADR_12 PMADR_11 PMADR_10 PMADR_9 PMADR_8 PMADR_7 PMADR_6 PMADR_5 PMADR_4 PMADR_3 PMADR_2 PMADR_1 R188 10K J PMADR_23 R189 10K J PMADR_22 R190 10K J PMADR_21 PMADR_23 PMADR_22 PMADR_21 PMADR_20 PMADR_19 PMADR_18 PMADR_17 PMADR_16 PMADR_15 PMADR_14 PMADR_13 PMADR_12 PMADR_11 PMADR_10 PMADR_9 PMADR_8 PMADR_7 PMADR_6 PMADR_5 PMADR_4 PMADR_3 PMADR_2 PMADR_1 PMADR_14 PMADR_13 PMADR_12 PMADR_11 PMADR_10 PMADR_9 PMADR_8 PMADR_7 PMADR_6 PMADR_5 PMADR_4 PMADR_3 PMADR_2 PMADR_1 FLASH_RSTZ P3P3V PM_CSZ_0 PM_CSZ_1 12 RESET 47 BYTE 11 WE PM_OESZ PM_OESZ 28 OE FLASH_CSSZ FLASH_CSSZ 33 J 33 J PM_WESZ PM_OESZ 26 VSS VSS 27 46 GND C330 0.1U K 45 43 41 39 36 34 32 30 44 42 40 38 35 33 31 29 PMDAT_15 PMDAT_14 PMDAT_13 PMDAT_12 PMDAT_11 PMDAT_10 PMDAT_9 PMDAT_8 PMDAT_7 PMDAT_6 PMDAT_5 PMDAT_4 PMDAT_3 PMDAT_2 PMDAT_1 PMDAT_0 BUSY R43 10K J R44 10K J 14 P27 P28 R193 R194 33 J 33 J Y30 Y28 SDRAM_RASZ SDRAM_CASZ R195 R196 33 J 33 J W30 V27 SDRAM_CLK SDRAM_CKE R197 R198 33 J 33 J SDRAM_CSZ FLASH_CSZ R199 R48 33 J 33 J P3P3V R202 10K J GGE[7:0] 7 PMDAT_[15:0] 15 P3P3V CE GRE[7:0] GGE7 GGE6 GGE5 GGE4 GGE3 GGE2 GGE1 GGE0 A12 D14 D13 C13 B13 A13 C14 A14 D15 PORT1_B_8 PORT1_B_7 PORT1_B_6 PORT1_B_5 PORT1_B_4 PORT1_B_3 PORT1_B_2 PORT1_B_1 PORT1_B_0 GRE7 GRE6 GRE5 GRE4 GRE3 GRE2 GRE1 GRE0 D10 C10 B10 A10 D11 C11 C12 E14 B12 PORT1_C_8 PORT1_C_7 PORT1_C_6 PORT1_C_5 PORT1_C_4 PORT1_C_3 PORT1_C_2 PORT1_C_1 PORT1_C_0 B19 A11 D12 A9 B9 PORT1_FLD/GPIO_14 PORT1_VSYNC PORT1_HSYNC PORT1_DATEN PORT1_CLK D18 A19 A8 D9 C9 ADC_COAST/GPIO_04 ADC_CLAMP/GPIO_05 ALF_VSYNC ALF_HSYNC ALF_CSYNC PMDAT_[15:0] 7 7 AD_VS AD_HS 7 AD_CLK AD_VS AD_HS AD_CLK WP/ACC 7 7 3 3 7 S29GL032A-90TFIR42 AD_COAST AD_CLAMP VSYNC_I HSYNC _I AD_SOG AD_COAST AD_CLAMP VSYNC_I HSYNC_I AD_SOG SDRAM_DQMS_1 SDRAM_DQMS_0 PMADR_14 PMADR_13 PMADR_12 PMADR_11 PMADR_10 PMADR_9 PMADR_8 PMADR_7 PMADR_6 PMADR_5 PMADR_4 PMADR_3 PMADR_2 PMADR_1 PMADR_0 21 20 36 35 22 34 33 32 31 30 29 26 25 24 23 SDRAM_CLKS SDRAM_CKES 38 37 CLK CKE SDRAM_CASSZ SDRAM_RASSZ SDRAM_CASSZ SDRAM_RASSZ 17 18 CAS RAS SDRAM_DQMS_1 SDRAM_DQMS_0 SDRAM_DQMS_1 SDRAM_DQMS_0 39 15 DQMH DQML SDRAM_CSSZ PM_WESZ 19 16 CS WE 40 NC2 SDRAM_CLKS SDRAM_CKES SDRAM_CSSZ FLASH_CSSZ SDRAM_CSSZ PM_WESZ 6 U28 SDRAM_RASSZ SDRAM_CASSZ R49 FLASH_RSTZ BA1 BA0 NC1 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 NC VD_YUV[9:0] PMDAT_[15:0] DATA15 DATA14 DATA13 DATA12 DATA11 DATA10 DATA9 DATA8 DATA7 DATA6 DATA5 DATA4 DATA3 DATA2 DATA1 DATA0 0J 53 51 50 48 47 45 44 42 13 11 10 8 7 5 4 2 PMDAT_15 PMDAT_14 PMDAT_13 PMDAT_12 PMDAT_11 PMDAT_10 PMDAT_9 PMDAT_8 PMDAT_7 PMDAT_6 PMDAT_5 PMDAT_4 PMDAT_3 PMDAT_2 PMDAT_1 PMDAT_0 P3P3V VDD VDD VDD 1 14 27 P3P3V VDDQ VDDQ VDDQ VDDQ 3 9 43 49 P3P3V VSS VSS VSS VSSQ VSSQ VSSQ VSSQ 28 41 54 6 12 46 52 C323 C324 C325 0.1U K 0.1U K 0.1U K For SDRAM VDD P3P3V C326 C327 C328 C329 0.1U K 0.1U K 0.1U K 0.1U K For SDRAM VDDQ 97 Confidential - Do Not Copy PJ513D-1 TP232 TP41 TP39 TP40 VD_YUV0 TP42 AH21 D8 C8 B8 A7 PORT2_VSYNC PORT2_HSYNC PORT2_DATEN PORT2_CLK VD_YUV9 VD_YUV8 VD_YUV7 VD_YUV6 VD_YUV5 VD_YUV4 VD_YUV3 VD_YUV2 VD_YUV1 A4 B5 A5 C5 E7 C6 B6 D7 A6 PORT3_DAT_9 PORT3_DAT_8 PORT3_DAT_7 PORT3_DAT_6 PORT3_DAT_5 PORT3_DAT_4 PORT3_DAT_3 PORT3_DAT_2 PORT3_DAT_1 C7 PORT3_CLK GPIO_28 TP43 6 K4S641632K-UC75 ViewSonic Corporation PORT1_A_8 PORT1_A_7 PORT1_A_6 PORT1_A_5 PORT1_A_4 PORT1_A_3 PORT1_A_2 PORT1_A_1 PORT1_A_0 3,4,5,6,7,9,10,11,12,13,14,15,16,17 7 DQ15/A-1 DQ14 DQ13 DQ12 DQ11 DQ10 DQ9 DQ8 DQ7 DQ6 DQ5 DQ4 DQ3 DQ2 DQ1 DQ0 C15 B15 A15 A16 B16 E17 C16 D16 A17 PM_WESZ PM_OESZ SDRAM_CLKS SDRAM_CKES POSENSE A21 A20 A19 A18 A17 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 PM_WESZ DDP2230-2507650-1 13 FLASH_RSTZ R42 10K J 13 10 9 16 17 48 1 2 3 4 5 6 7 8 18 19 20 21 22 23 24 25 PM_WESZ AA29 W28 SDRAM_DQM_1 W27 SDRAM_DQM_0 GBE7 GBE6 GBE5 GBE4 GBE3 3,6,7,9,10,11,13,14,15,16,17 GBE2 GBE1 GBE0 P3P3V C86 0.1U K PMADR_0 W29 PM_WEZ R46 Y27 PM_OEZ R47 AA30 AA28 37 PMADR_[1:23] PMADR_[0:14] PM_CSZ_2 GBE[7:0] P3P3V P3P3V PM_WEZ PM_OEZ 7 U14 VD_CLK DDP2230-2507650-1 P3P3V SW1 S D 6,7,11,17 6,7,11,17 R65 USB_EN 4 4 AF29 AF30 IIC_0_SDA IIC_0_SCL R66 1.5K G 3.3K J USB_EN SDA SCL SDA SCL USB_DUSB_D+ USB_DUSB_D+ P3P3V 13 15 14 13,14,15 13 13,14,15 R204 3.3K J R67 R68 27 27 E29 E30 SSP0_CSZ2 SSP0_CSZ1 SSP0_CSZ0 SSP0_CLK SSP0_RXD SSP0_TXD SSP0_CSZ2 SSP0_CSZ1 SSP0_CSZ0 SSP0_CLK SSP0_RXD SSP0_TXD AG20 AH22 AG22 AH23 AK27 AJ23 UART0_RXD UART0_TXD UART0_CTSZ UART0_RTSZ 4 UART0_RXD 4 UART0_TXD 4 UART0_CTSZ 4 UART0_RTSZ D23 A24 C23 B22 USB_DAT_N USB_DAT_P SSP0_CSZ_2 SSP0_CSZ_1 SSP0_CSZ_0 SSP0_CLK SSP0_RXD SSP0_TXD UART0_RXD UART0_TXD UART0_CTSZ UART0_RTSZ P5V PWRGOOD MTR_ARSTZ EXT_ARSTZ POSENSE AJ28 A18 C17 AK28 PWRGOOD MTR_ARSTZ EXT_ARSTZ POSENSE 1 AD27 AA27 GPIO_31 GPIO_30 GPIO_29 A27 IRRC VR F27 TP235 AK20 GPIO_27 GPIO_26 GPIO_25 GPIO_24 GPIO_23 GPIO_22 GPIO_21 GPIO_20 GPIO_19 GPIO_18 GPIO_17 GPIO_16 GPIO_15 GPIO_13 GPIO_12 GPIO_11 GPIO_10 GPIO_9 GPIO_8 GPIO_7 GPIO_6 A25 D25 E24 D24 C24 A26 B25 D30 C18 B18 AG21 AH20 C25 A21 C21 B21 D21 A22 A23 D22 C22 AUDIO_VOL AUDIO_MUT PWR_LEDG PW R_LEDR TEMP_LEDG TEMP_LEDR LAMP_LEDG LAMP_LEDR KETPD_PWR KEYPD_SEL KEYPD_AUTO KEYPD_MENU KEYPD_UP KEYPD_DOWN KEYPD_LEFT KEYPD_RIGHT KEYPD_MODE reserved PWM_AUDIO3 PWM_AUDIO2 PWM_AUDIO1 D19 A20 C20 D20 LAMPLITZ_I R70 LAMP_RXD_I R71 LOW_P PWR_DOWN LMPSTAT LMPCTRL AUDIO_SW FAN_SW KEYPD_PWR KEYPD_SEL KEYPD_AUTO KEYPD_MENU KEYPD_UP KEYPD_DOWN KEYPD_LEFT KEYPD_RIGHT KEYPD_MODE AUDIO_SW FAN_SW 17 USB_EN TP234 USB_EN IRRCVR 5 TP192 TP193 KEYPD_PWR KEYPD_SEL KEYPD_AUTO KEYPD_MENU KEYPD_UP KEYPD_DOWN KEYPD_LEFT KEYPD_RIGHT KEYPD_MODE OPEN 0J 0J 4.7K J R62 4.7K J R61 4.7K J R60 4.7K J R59 4.7K J 4.7K J 2 2 5 4 6B40065031 CK3 MMBT2222ALT1G LAMPLITZ LAMP_RXD 5 LOW_P PWR_DOWN 5 CW_PWM CW_INDEX AD26 CWINDEX EEPROM FOR DDP2230 RK11 330 CWINDEX R211 P3P3V 3,6,7,8,10,11,13,14,15,16,17 U31 R212 PWR_LEDG PWR_LEDG PW R_LEDR PW R_LEDR R213 B 47 J R214 B 47 J 8 2 A1 WP 7 3 A2 SCL 6 SCL 4 GND SDA 5 SDA 5 4 CK8 680P J 6B40065031 SW10 1 SW11 1 2 3 3 5 4 CK9 680P J 6B40065031 2 5 4 CK10 680P J 6B40065031 LTST-C155GEKT G 5 4 CK6 680P J 6B40065031 R QK7 2N3904S QK8 2N3904S RK12 330 C VCC 2 3 E DDP2230-2507650-1 A0 SW9 1 3 E C331 0.1U K 1 SW8 1 2 P5VS 4.7K J 4.7K J CW_PWM 16 5 4 CK4 680P J 6B40065031 5 4 CK5 680P J 6B40065031 2 3 AB27 2 3 3 C P3P3V CW_PWM SW6 1 2 Q4 PMD_INTZ PMD_INTZ PMD_INTZ SW5 1 LAMP_RXD 5 LED6 13 5 4 CK1 680P J 6B40065031 5 4 CK2 680P J 6B40065031 680P J P3P3VS AD28 2 3 4 OPEN L: Lamp on H: Lamp off 3 3 TP200 1 OPEN L: Lamp on H: Lamp off 470 LED2 GRN A K SW2 1 R64 SW3 1 SW4 1 AUDIO_VOL reserved AUDIO_MUT reserved PWR_LEDG CK7 PW R_LEDR TEMP_LEDG 680P J TEMP_LEDR LAMP_LEDG LAMP_LEDR KEYPD_PWR KEYPD_SEL KEYPD_AUTO KEYPD_MENU 100 J R73 1 KEYPD_UP LOW_P KEYPD_DOWN KEYPD_LEFT KEYPD_RIGHT TP194 KEYPD_MODE TP195 reserved TP196 PWM_AUDIO3 PWM_AUDIO2 PWM_AUDIO1 470 LED1 GRN A K R63 3 LAMPLIT AJ22 C19 AJ21 AH24 B26 GPIO_3 GPIO_2 GPIO_1 GPIO_0 5 3,4,5,6,7,13,16,17 13 PWRGOOD P5V 13 MTR_ARSTZ 6,14,15 EXT_ARSTZ R69 13 POSENSE 100K F P3P3V C87 0.1U K U15 74AHC1G08GW 1 LAMPLITZ 4 2 3 2 MMBT2222ALT1G Q3 LAMPLITZ 5 LAMPEN C88 R72 GPIO_39 GPIO_38 GPIO_37 GPIO_36 GPIO_35 R58 TP191 R57 Q2 APM2301CAC P5VS 3 P3P3V 4.7K J 4.7K J TP233 R56 6B40019001 R55 P3P3VS 4.7K J DDP2230 2 1 R54 3 4 2 P3P3V U13G R51 1K J 3.3K J 4.7K J R50 1K J R52 R53 3,6,7,8,10,11,13,14,15,16,17 P3P3V AT24C32AN-10SU-2.7 P3P3VS LED3 P5VS P3P3VS LTST-C155GEKT RK1 P5VS RK2 LED4 LTST-C155GEKT RK3 RK4 LED5 P5VS 2 1 2 P3P3VS 1 4,5 2 P5VS 1 P3P3VS LTST-C155GEKT 4.7K J 4.7K J TEMP_LEDG TEM_LEDG QK4 2N3904S RK8 330 TEMP_LEDR TEM_LEDR R179 B 47 J R182 B 47 J R181 47 J B QK2 2N3904S LAMP_LEDG LAMP_LEDG QK5 2N3904S LAMP_LEDR LAMP_LEDR R183 B 47 J 98 Confidential - Do Not Copy 4 3 B 47 J 330 VCC C89 0.1U K 4 Y A 1 B 2 GND 3 CWINDEXA GND CWINDEXA 16 3,4,5,6,7,8,10,11,12,13,14,15,16,17 74AHC1G32GV QK3 2N3904S E RK9 ViewSonic Corporation R180 E C E PW R_LEDR C PW R_LEDR RK7 CWINDEX 5 E QK1 2N3904S B 47 J 330 R U16 P3P3V QK6 2N3904S C R178 4.7K J 4.7K J E PWR_LEDG E PWR_LEDG C RK6 G C 4.7K J 4.7K J R 4 3 G 4 R75 R C R74 330 3 RK5 G 5 330 RK10 PJ513D-1 330 Keypad and LED circuit U13I P1P2V U13J DDP2230 P1P2V AA26 AF10 AF11 AF12 AF13 AF18 AF19 AF20 AF21 E10 E11 E12 E13 E18 E19 E20 E21 K26 L26 L4 L5 M13 M15 M16 M18 M26 N12 N15 N16 N19 N26 R12 R13 R18 R19 T12 T13 T18 T19 V12 V15 V16 V19 V26 W13 W15 W16 W18 W26 W5 Y26 Y5 P1P2V DDP2230 3,6,7,8,9,11,13,14,15,16,17 P3P3V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V PIP2V PIP2V PIP2V PIP2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V PIP2V PIP2V PIP2V PIP2V P1P2V P1P2V P1P2V P1P2V P1P2V P1P2V P3P3V P3P3V P3P3V P3P3V P3P3V P3P3V P3P3V P3P3V P3P3V P3P3V P3P3V P3P3V P3P3V P3P3V P3P3V P3P3V P3P3V P3P3V P3P3V P3P3V P3P3V P3P3V P3P3V AC26 AE26 AF23 AF25 AG29 AJ20 AJ27 D29 F26 H26 L29 R26 Y29 B11 B20 B23 B27 B4 E15 E23 E25 E6 E8 P3P3V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V VDDA VDDA VDDA VDDA VDDA VDDA VDDA VDDA VDDA VDDA VDDA VDDA VDDA VDDA VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO VDDIO AF16 AF6 AF8 AG14 AH11 AH19 AJ4 A1P2VA AF4 AF5 AG1 AG2 AG3 AG4 D1 D2 D3 D4 E4 E5 T5 U5 A1P2VIO AA1 AA2 AE1 12 AE2 F1 F2 K1 K2 A1P2VIO DDP2230-2507650-1 3,4,5,6,7,8,9,11,12,13,14,15,16,17 GND A1 A2 A28 A29 A3 A30 AA3 AB26 AB3 AC3 AD29 AD3 AE3 AF15 AF22 AF26 AF3 AF9 AG27 AG5 AG7 AH1 AH14 AH17 AH2 AH26 AH28 AH3 AH4 AJ1 AJ2 AJ24 AJ29 AJ7 AK1 AK2 AK21 AK30 AK7 B1 B14 B17 B2 B24 B29 B3 B7 C28 C3 C4 D26 D27 D5 D6 E16 E22 E26 E3 E9 F3 G29 G3 H3 J3 J26 R17 GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND M12 M14 M17 M19 M3 N13 N14 N17 N18 N2 N4 N5 P1 P12 P13 P14 P15 P16 P17 P18 P19 P29 P3 R14 R15 R16 R2 W19 R5 T14 T15 T16 T17 T2 T26 T3 U12 U13 U14 U15 U16 U17 U18 U19 U2 U29 U4 V1 V13 V14 V17 V18 V3 M1 V5 W12 W14 W17 W2 W4 Y1 Y3 C1 C2 L2 K3 C143 C144 C145 C146 C147 C148 C149 C150 C151 C152 C153 C154 C155 10U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 130.1U Z P1P2V C157 C158 C159 C160 C161 C162 C163 C164 C165 C166 C167 C168 C169 C170 10U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z L22 C206 A1P2V C225 C226 C227 C228 C229 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z A1P2VA A1P2VIO L23 Z300 C207 C202 C203 C204 C205 C208 C209 C210 10U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 10U Z 13 DDP2230 XIO VDDA BYPASSING TRACEPKT[0:7] Z300 C230 C231 C232 C233 C234 C235 C211 10U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 1U K TRACEPKT[0:7] TRACEPKT[0:7] DDP2230 TRACEPKT7 TRACEPKT6 TRACEPKT5 TRACEPKT4 TRACEPKT3 TRACEPKT2 TRACEPKT1 TRACEPKT0 PIPESTAT2 PIPESTAT1 PIPESTAT0 TRACESYNC TRACECLK RTCK G30 F30 E28 G28 F29 F28 G27 G26 PIPESTAT2 PIPESTAT1 PIPESTAT0 D28 C30 E27 TRACESYNC C29 TRACECLK B30 RTCK C26 R76 4.7K J AK3 TSTPT_7 TSTPT_6 TSTPT_5 TSTPT_4 TSTPT_3 TSTPT_2 TSTPT_1 TSTPT_0 AD30 AC27 AC28 AC29 AC30 AB28 AB30 AB29 TDO1 TDO2 TMS2 TMS1 TDI TCK TRSTZ AG24 AG23 AK24 AG25 AJ25 AF24 AK26 MFG_TEST_7 MFG_TEST_6 MFG_TEST_5 MFG_TEST_4 MFG_TEST_3 MFG_TEST_2 MFG_TEST_1 MFG_TEST_0 AG17 AG19 AF17 AF7 AG11 AF14 AH12 AK4 ETM_TRACEPKT7 ETM_TRACEPKT6 ETM_TRACEPKT5 ETM_TRACEPKT4 ETM_TRACEPKT3 ETM_TRACEPKT2 ETM_TRACEPKT1 ETM_TRACEPKT0 ETM_PIPESTAT2 ETM_PIPESTAT1 ETM_PIPESTAT0 ETM_TRACESYNC ETM_TRACECLK RTCK MFG_TEST_EN ICTSENZ P1P8V TP81TP82TP83 TDO1 TDO2 TMS2 TMS1 TDI TCK TRSTZ DDP2230-2507650-1 DDP2230-2507650-1 P1P8V P1P2V C130 C131 C132 C133 C134 C135 C136 C137 C138 C139 C140 C141 C142 C215 C216 C217 C218 C219 C220 C221 C222 C223 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 10U Z 10U Z P3P3V P3P3V C91 C92 C93 C94 C95 C96 C97 C98 C99 C100 C101 C102 C104 C105 C106 C107 C108 C109 C110 C111 C112 C113 C114 C117 C118 C119 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 10U Z 10U Z 10U Z PJ513D-1 0.1U Z DDP2230 XIO VDDIO BYPASSING U13H 6,12,13 Confidential - Do Not Copy C224 A1P2V A1P2V P1P8V ViewSonic Corporation P1P2V P1P2V AK25 99 C156 TDO1 TDO2 TMS2 TMS1 TDI TCK TRSTZ TP210 TP211 TP212 TP213 TP214 TP215 TP216 TP217 TP218 TRACEPKT0 TRACEPKT1 TRACEPKT2 TRACEPKT3 TRACEPKT4 TRACEPKT5 TRACEPKT6 TRACEPKT7 PWRGOOD TP219 TP220 TP221 TP222 TP223 TP224 TP225 TP226 TP227 TP228 TP229 TP230 TP231 PIPESTAT0 PIPESTAT1 PIPESTAT2 TRACESYNC TRACECLK RTCK TDO1 TDO2 TMS1 TMS2 TDI TCK TRSTZ PWRGOOD 13 PIPESTAT0 PIPESTAT1 PIPESTAT2 TRACESYNC TRACECLK RTCK TDO1 TDO2 TMS1 TMS2 TDI TCK TRSTZ P2P5V U13F A1P8V P3P3V L20 Z70 13 L34 Z70 P3P3V C182 0.1U K 1 VDD VDD VDD U18 7 EN 20MHZ 8 SPARE_0 AK22 VDD_PLL XCG_EN AH25 XCG_OEN XCG_EN C181 0.1U K AK23 C184 0.1U K R78 D17 OCLKA 33.2 F OCLKA OCLKA 16 VSS_PLL R80 20MHZ 5 20MHZ_A AJ26 300MHZ 300MHZ 14 13 100MHZ 100MHZ 18 17 CLK_300MHZ_P CLK_300MHZ_N R81 R82 33.2 F 33.2 F CLK_300MHZ_PA CLK_300MHZ_NA AJ5 AK5 B28 C27 AG26 AH5 AH27 AK29 NC_B28 NC_C27 NC_AG26 NC_AH5 NC_AH27 NC_AK29 MOSC 49.9 F XIN Y2 20MHZ 2 C183 0.1U K AG12 4 11 19 R79 4.7K J A1P8V C180 0.1U K 8,9,10,13,14,15,16,17 P3P3V R77 4.7K J DDP2230 CLKFL_P CLKFL_N DDP2230-2507650-1 XOUT IDO CLK_100MHZ_P CLK_100MHZ_N R83 R86 33.2 F 33.2 F R84 49.9 F R85 49.9 F R87 1K J R88 R89 49.9 F49.9 F SDA 9 SDA SCL 10 SCL 20 IREF R91 680 VSS VSS VSS VSS VSS C350 10P J P2P5V 3 6 12 15 16 P2P5V 6,13 GND P2P5V 3,4,5,6,7,8,9,10,12,13,14,15,16,17 C185 0.1U K R92 R90 40.2 F40.2 F R93 CDCDLP223 XDR_RQ_CTMP 4.7K J XDR_RQ_CTMP 12 U19A 6,7,9,17 SDA 9 14 SCL CLK_100MHZ_PA CLK_100MHZ_NA P2P5V P2P5V_XCG_VDD R94 1K J R96 1K J U19B 15 22 28 7 VDD VDD VDD VSS VSS VSS VSS VDDC VSSC 4 18 21 25 6,7,9,17 9 8 13 12 CLK0 CLK0B 27 26 REFCLK REFCLKB CLK1 CLK1B 24 23 ID1 ID0 CLK2 CLK2B 20 19 CLK3 CLK3B 17 16 SDA SCL 10 9 SDA SCL XCG_EN 11 EN SDA SCL XCG_EN 5 6 BAPASS ISET P2P5V_XCG_VDDP 1 VDDP VSSP CDCD5704PW CDCD5704PW P2P5V 6,13 P2P5V_XCG_VDD P2P5V_XCG_VDDP P2P5V L24 Z300 P2P5V C245 C246 C247 C248 C249 C250 C251 10U Z 0.1U Z 10U Z 0.1U Z 1000P K 1000P K 1000P K 1000P K L25 C252 Z300 C253 C254 1000P K 0.1U Z XCG BYPASSING ViewSonic Corporation 100 Confidential - Do Not Copy 2.7N K 2.7N K C188 2.7P C P2P5V R95 OPEN C189 OPEN XDR_RQ_CTMN PJ513D-1 C255 1U K C256 10U Z XDR_RQ_CTMN 12 TP51 C190 OPEN HDR_XCG_CLK3_P R97 OPEN 3 R98 330 J TP52 2 C186 C187 TP53 C191 OPEN HDR_XCG_CLK3_N XDR_DQN[7:0] A1P2V_TERM U13B R101 RQ VREF GENERATION DDP2230 XDR_RQ_VREF XIO_RQ_VREF XDR_DQP[7:0] A1P2V_TERM XDR_DQ0N7 XDR_DQ0P7 XDR_DQ0N6 XDR_DQ0P6 XDR_DQ0N5 XDR_DQ0P5 XDR_DQ0N4 XDR_DQ0P4 XDR_DQ0N3 XDR_DQ0P3 XDR_DQ0N2 XDR_DQ0P2 XDR_DQ0N1 XDR_DQ0P1 XDR_DQ0N0 XDR_DQ0P0 XDR_DQN7 XDR_DQP7 XDR_DQN6 XDR_DQP6 XDR_DQN5 XDR_DQP5 XDR_DQN4 XDR_DQP4 XDR_DQN3 XDR_DQP3 XDR_DQN2 XDR_DQP2 XDR_DQN1 XDR_DQP1 XDR_DQN0 XDR_DQP0 F5 F4 G5 G4 G2 G1 H5 H4 H2 H1 J5 J4 J2 J1 K5 K4 RN1 XDR_RQ11 5 XDR_RQ10 6 XDR_RQ9 7 XDR_RQ8 8 XDR_RQ7 5 XDR_RQ6 6 XDR_RQ5 7 XDR_RQ4 8 XDR_RQ3 5 XDR_RQ2 6 XDR_RQ1 7 XDR_RQ0 8 R103 100 J C259 C260 C261 C262 0.1U K 0.1U K 0.1U K R185 OPEN 0.1U K 39 4 3 2 1 4 3RN2 2 1 39 4 3 2 1 RN3 39 C258 0.1U K 39.2 F R105 62 F A1P2VIO A1P2VIO TP54 TP55 R191 10K J TP56 TP57 AJ3 AH6 AH7 AG6 SIF_CK SIF_RESETZ SIF_DI SIF_DO XDR_RQ_CTMP R4 XDR_RQ_CTMN T4 11 XDR_RQ_CTMP 11 XDR_RQ_CTMN XDR_DQ1_RLOAD W3 W1 V4 V2 U3 U1 P4 P2 N1 N3 M4 M2 XDR_RQ11 XDR_RQ10 XDR_RQ9 XDR_RQ8 XDR_RQ7 XDR_RQ6 XDR_RQ5 XDR_RQ4 XDR_RQ3 XDR_RQ2 XDR_RQ1 XDR_RQ0 XDR_RST XDR_CFM XDR_CFMN XDR_CMD L3 R1 T1 Y2 XDR_RQ_CFMP XDR_RQ_CFMN XDR_SCK XDR_SRD XDR_RQVREF XDR_RQROLREF XDR_RQVOLREF XDR_RQ11 XDR_RQ10 XDR_RQ9 XDR_RQ8 XDR_RQ7 XDR_RQ6 XDR_RQ5 XDR_RQ4 XDR_RQ3 XDR_RQ2 XDR_RQ1 XDR_RQ0 XDR_RQ_RST XDR_RQ_CFMP XDR_RQ_CFMN A1P2V_TERM R102 39.2 F H4 H3 H13 H14 G13 G14 E14 D3 D4 D14 D13 C3 RQ11 RQ10 RQ9 RQ8 RQ7 RQ6 RQ5 RQ4 RQ3 RQ2 RQ1 RQ0 C15 RST G3 G4 CFM CFMN XDR_RQ_CMD J14 XDR_RQ_SCK J15 CMD SCLK C1 K11 J5 C5 B11 VTERM_K11 VTERM_J5 VTERM_C5 VTERM_B11 U20A R126 49.9 F SDI R127 10K J XDR_RQ_CFMP XDR_RQ_CFMN XDR_RQ_CMD R104 39.2 F R106 39.2 F XDR_DQ0VREF XDR_DQ0RLOAD XDR_DQ1VREF XDR_DQ1RLOAD E13 XDR_RQ[0:11] XDR_RQ_RST A1P2VIO XDR_DQ0_RLOAD A1P2VIO XDR_RQ11 XDR_RQ10 XDR_RQ9 XDR_RQ8 XDR_RQ7 XDR_RQ6 XDR_RQ5 XDR_RQ4 XDR_RQ3 XDR_RQ2 XDR_RQ1 XDR_RQ0 XDR_CTM XDR_CTMN E2 E1 AF2 AF1 AE5 AE4 AD5 AD4 AD2 AD1 AC5 AC4 AC2 AC1 AB5 AB4 AB2 AB1 AA5 AA4 VREF_E13 XDR_DQ1N7 XDR_DQ1P7 XDR_DQ1N6 XDR_DQ1P6 XDR_DQ1N5 XDR_DQ1P5 XDR_DQ1N4 XDR_DQ1P4 XDR_DQ1N3 XDR_DQ1P3 XDR_DQ1N2 XDR_DQ1P2 XDR_DQ1N1 XDR_DQ1P1 XDR_DQ1N0 XDR_DQ1P0 XDR_RQ_VREF Y4 L1 XDR_RQ_SCK XDR_RQ_SRD R3 M5 P5 XIO_RQ_VREF XDR_DQC_ROLREF XDR_DQC_VOLREF A1P2V_TERM A1P2VIO XDR_DQP7 DQN15 DQ15 DQN14 DQ14 DQN13 DQ13 DQN12 DQ12 DQN11 DQ11 DQN10 DQ10 DQN9 DQ9 DQN8 DQ8 L3 L4 A3 A4 K13 K14 B13 B14 L15 L16 A15 A16 K1 K2 B1 B2 DQN7 DQ7 DQN6 DQ6 DQN5 DQ5 DQN4 DQ4 DQN3 DQ3 DQN2 DQ2 DQN1 DQ1 DQN0 DQ0 L13 L14 A13 A14 K3 K4 B3 B4 L1 L2 A1 A2 K15 K16 B15 B16 SDO XDR_RQ_SRD RESV_E3 RESV_E4 A1P2VIO XIO_RQ_VREF R109 R110 R113 49.9 F 75 J 150 J C263 0.1U K R111 49.9 F XDR_DQP6 R112 49.9 F C264 C265 0.1U K 0.1U K XDR_DQ0_RLOAD XDR_DQ1_RLOAD XDR_DQP5 U20B XDR_DQP4 P1P8V XDR_DQP3 6,10,13 XDR_DQP2 P1P8V XDR_DQP1 XDR_DQP0 XDR_DQN7 XDR_DQN6 XDR_DQN5 XDR_DQN4 A1P2VIO XDR_DQN3 XDR_DQN2 R99 51 XDR_DQN1 R100 51 C257 0.1U K A5 A12 B5 C13 D1 D6 D11 D16 E6 F5 F12 G1 G11 G16 H16 J1 J2 J3 J13 K5 L5 L12 P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V P1P8V GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND GND XDR_DQN0 A6 A11 B6 B12 C2 C4 C12 C14 E1 E11 E16 F6 F11 G6 H1 H6 H11 J4 J12 J16 K6 K12 L6 L11 XDR_RQ_CFMP XDR_RQ_CFMN C16 XDR_RQ_SRD XDR_RQ_SRD E3 E4 GND R107 165 F 3,4,5,6,7,8,9,10,11,13,14,15,16,17 R108 165 F EDX5116ACSE-3C-E EDX5116ACSE-3C-E A1P2VIO P1P8V ( XDR MEMORY I/F ) A1P2VIO L21 RQ TERMINATION BYPASSING C309 0.1U Z C310 0.1U Z C311 0.1U Z C312 0.1U Z C313 0.1U Z C314 0.1U Z C315 0.1U Z C316 0.1U Z Z300 2 C318 0.1U Z C236 C237 C238 C239 C240 C241 C242 C243 C244 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 10U Z 1U K XDR MEMORY VDDIO BYPASSING A1P2VIO C192 + 220U 16V <Spec> C317 0.1U Z A1P2V_TERM 1 10 C308 0.1U Z C193 C194 C195 C196 C197 C198 C199 C200 C201 1U K 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z 0.1U Z P1P8V ,13,14,15,16,17 GND C319 10U Z ViewSonic Corporation C320 0.1U Z C321 0.1U Z C322 0.1U Z XDR MEMORY VDDMEM BYPASSING 101 Confidential - Do Not Copy PJ513D-1 C266 P12V P12V 0.33U K C273 0.22U K 18 17 C275 0.22U K R138 1.6K F 28 CP1 0.1 20 VREG 47 TRIM GDC 26 LXC 25 L26 5,14,16,17 P1P2V D30 A Q5 NDT3055 G CP2 P12V R133 K SMPI0603HW-4R7M-A01 MURS220T3G D14 SS3P4 P1P2V C274 47U 6.3V R135 1K B R137 2K B D2 D1 P1P8V A1P2V Q6 NDT3055 FB1 29 VLIN1 V2P5 46 LX25 41 PMD1000 6,10,12 G R142 30 P2P5V L27 P2P5V 10U D15 PMEG2020EJ 33 GD2 32 FB2 6,11 C277 47U 6.3V S A1P2V P1P8V 31 FBC K A1P8V C276 4.7U M 10 ISEN VCP R136 2K B A1P8V 11 27 K 21 ISENK A C270 C271 C272 0.33U K 0.33U K 0.33U K A C269 10U K U21A D1 D2 C268 10U K VBB1 VBB2 VBB4 S 9 22 42 C278 47U 6.3V R143 2K B 24 V5 23 LX5 V3P3 45 LX33 43 P3P3V L29 P3P3V K 1K B 10UH D16 PMEG2020EJ L30 Master K 3,4,5,6,7,9,16,17 P5V 15U M C279 22U K A P5V D17 PMEG2020EJ A C280 22U K 3,4,5,6,7,8,9,10,11,12,14,15,16,17 GND P3P3V 3,6,7,8,9,10,11,14,15,16,17 P3P3V R128 R129 R130 R131 3.3K J 3.3K J 3.3K J 3.3K J U21B 9,10 PWRGOOD 8,9 9 POSENSE PMD_INTZ PWRGOOD 35 PWRGOOD F3SW 38 TP77 POSENSE 34 POSENSE F2SW 39 TP78 PMD_INTZ 36 F1SW 40 TP79 PMDINTZ P3P3V R132 3.3K J PMD1000 9 ViewSonic Corporation MTR_ARSTZ MTR_ARSTZ 48 102 Confidential - Do Not Copy 4 CLK 2 SSP0_CLK SSP0_CLK 9 DOUT 1 SSP0_RXD SSP0_RXD 9,14,15 DIN 3 SSP0_TXD SSP0_TXD 9 RESETZ PJ513D-1 SSP0_CSZ2 CSZ SSP0_CSZ2 9 3,6,7,8,9,10,11,14,15,16,17 10 P3P3V 3,6,7,8,9,10,11,13,15,16,17 P3P3V R146 1K J R192 3.3K J MBRST[15:0] MBRST[15:0] 15 U13E U22 DAD_INTZ DAD_INTZ AE30 DAD_STRB AF28 DAD_MODE_1 DAD_MODE_0 AH29 AJ30 DAD_STRB DAD_MODE_1 DAD_MODE_0 DAD_SEL_1 DAD_SEL_0 AE28 AE29 DAD_SEL_1 DAD_SEL_0 AF27 AG28 AE27 AH30 DAD_ADDR_3 DAD_ADDR_2 DAD_ADDR_1 DAD_ADDR_0 DAD_ADDR_3 DAD_ADDR_2 DAD_ADDR_1 DAD_ADDR_0 DAD_OEZ 9 DAD_INTZ 9 13 9 9 SSP0_CLK SSP0_TXD SSP0_RXD SSP0_CSZ0 SSP0_CLK SSP0_TXD SSP0_RXD SSP0_CSZ0 EXT_ARSTZ EXT_ARSTZ AG30 3,6,7,8,9,10,11,13,15,16,17 P3P3V P3P3V DDP2230-2507650-1 R148 SCP_CLK SCPDI SCPDO SCPENZ 15 2 3 4 5 STORBE MODE1 MODE0 SEL1 SEL0 16 17 18 19 A3 A2 A1 A0 45 44 DEV_ID1 DEV_ID0 59 6 RESETZ OEZ 54 NC P12V 52 51 NC NC 5,13,16,17 P12V 50 48 11 V12_3 V12_2 V12_1 C282 0.1U K C281 10U K 80 71 70 61 40 31 30 21 VBIAS_RAIL7 VBIAS_RAIL6 VBIAS_RAIL5 VBIAS_RAIL4 VBIAS_RAIL3 VBIAS_RAIL2 VBIAS_RAIL1 VBIAS_RAIL0 VBIAS VBIAS R150 0 VBIAS1 C290 C291 100N Z 100N Z C289 10U Z C292 2 VBIAS 9 VBIAS MBR0540T1G 8 D19 OUT15 OUT14 OUT13 OUT12 OUT11 OUT10 OUT09 OUT08 79 77 74 72 69 67 64 62 MBRST15 MBRST14 MBRST13 MBRST12 MBRST11 MBRST10 MBRST9 MBRST8 OUT7 OUT6 OUT5 OUT4 OUT3 OUT2 OUT1 OUT0 39 37 34 32 29 27 24 22 MBRST7 MBRST6 MBRST5 MBRST4 MBRST3 MBRST2 MBRST1 MBRST0 IRQZ 43 DAD_INTZ VOFF_RAIL7 VOFF_RAIL6 VOFF_RAIL5 VOFF_RAIL4 VOFF_RAIL3 VOFF_RAIL2 VOFF_RAIL1 VOFF_RAIL0 VOFF 78 73 68 63 38 33 28 23 49 VCC2 V5REG 47 VRST_RAIL7 VRST_RAIL6 VRST_RAIL5 VRST_RAIL4 VRST_RAIL3 VRST_RAIL2 VRST_RAIL1 VRST_RAIL0 76 75 66 65 36 35 26 25 VRST 13 Thermal Pad G1 VRST_SWL 12 DAD2000 1K J DAD_OEZ VBIAS 56 57 42 58 VBIAS_SWL P3P3V R147 1K J DAD_INTZ VCC2 D18 A VCC2 R149 0 VCC2A VCC2 VCC2 V5REG C284 100N Z C287 1U K C283 10U Z C285 100N Z C286 100N Z C288 100N Z VRST VRST VRST1 100N Z L31 22U M VBIAS_LHI R151 0 VRST VBIAS_LHI C293 100N Z MBR0540T1G VRST_SWL 2 3,4,5,6,7,8,9,10,11,12,13,15,16,17 GND C297 10U K 103 Confidential - Do Not Copy C298 100N Z PJ513D-1 VRST D20 1 7 14 20 41 46 53 55 60 10 GND GND GND GND GND GND GND GND GND 1 VBIAS_SWL ViewSonic Corporation BZX384-C8V2 K 1 DDP2230 L32 22U M C294 10U Z C295 100N Z C296 100N Z 15 J12 U13D TP109 P3P3V 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 DDP2230 DDB11_N DDB11_P DCLKB_P DCLKB_N DDB_P_7 DDB_N_7 DDB_P_6 DDB_N_6 DDB_P_5 DDB_N_5 DDB_P_4 DDB_N_4 DDB_P_3 DDB_N_3 DDB_P_2 DDB_N_2 DDB_P_1 DDB_N_1 DDB_P_0 DDB_N_0 AG13 AH13 AJ12 AK12 AJ11 AK11 AJ10 AK10 AG10 AH10 AJ8 AK8 AG8 AH8 AJ6 AK6 DDB1_P DDB1_N DDB3_P DDB3_N DDB5_P DDB5_N DDB7_P DDB7_N DDB9_P DDB9_N DDB11_P DDB11_N DDB13_P DDB13_N DDB15_P DDB15_N DDA_P_7 DDA_N_7 DDA_P_6 DDA_N_6 DDA_P_5 DDA_N_5 DDA_P_4 DDA_N_4 DDA_P_3 DDA_N_3 DDA_P_2 DDA_N_2 DDA_P_1 DDA_N_1 DDA_P_0 DDA_N_0 AJ13 AK13 AJ14 AK14 AG15 AH15 AJ15 AK15 AJ16 AK16 AJ18 AK18 AG18 AH18 AJ19 AK19 DDA1_P DDA1_N DDA3_P DDA3_N DDA5_P DDA5_N DDA7_P DDA7_N DDA9_P DDA9_N DDA11_P DDA11_N DDA13_P DDA13_N DDA15_P DDA15_N DCKB_P DCKB_N AJ9 AK9 DCLKB_P DCLKB_N DCKA_P DCKA_N AJ17 AK17 DCLKA_P DCLKA_N SCB_P SCB_N AG9 AH9 SCTRLB_P SCTRLB_N SCA_P SCA_N AG16 AH16 SCTRLA_P SCTRLA_N SCTRLB_P SCTRLB_N DDB1_N DDB1_P DDA1_P DDA1_N DDA5_P DDA5_N SCTRLA_P SCTRLA_N DDA9_P DDA9_N DCLKA_P DCLKA_N DDA15_N DDA15_P P3P3V 3,6,7,8,9,10,11,13,14,16,17 P3P3V R152 14 3.3K J TP151 P3P3V 9 9 SSP0_CSZ1 R155 33 J SSP0_CSZ1 EXT_ARSTZ TP150 VCC2 VCC2 R153 33 J DMD_MODE_B TP154 TP156 SSP0_CSZ1_DMD TP158 EXT_ARSTZ TP160 TP162 MBRST12 TP164 MBRST5 MBRST11 MBRST8 TP166 TP168 TP170 MBRST3 TP172 MBRST1 MBRST6 MBRST4 P3P3V 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 P3P3V 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 DDB15_P DDB15_N DDB13_P DDB13_N DDB9_P DDB9_N DDB7_P DDB7_N DDB5_N DDB5_P DDB3_P DDB3_N DDA3_P DDA3_N DDA7_P DDA7_N DDA11_P DDA11_N DDA13_N DDA13_P TP152 TP153 TP155 DMDSPAR0 TP157 SSP0_RXD_DMD SSP0_CLK_DMD TP159 SSP0_TXD_DMD TP161 TP163 MBRST14 TP165 MBRST13 MBRST10 TP167 MBRST7 TP169 TP171 MBRST0 TP173 MBRST9 MBRST2 MBRST15 2KC1001100 3,4,5,6,7,8,9,10,11,12,13,14,16,17 GND 1 3 7 6 2 6 OP3 OP OP4 OP H3 OP5 OP HOLE-V8 OP6 OP OP7 OP OP8 OP 1 1 3 7 2 6 2 6 OP9 OP H4 H5 HOLE-V8 HOLE-V8 OP10 OP OP11 OP OP12 OP OP13 OP OP14 OP Optical Points ViewSonic Corporation B MARK B1 B B2 B Screw Holes 3DJ8118001 1 OP2 OP 7 3DJ8118001 3DJ8118001 3DJ8118001 3DJ8118001 3DJ8118001 3DJ8118001 3DJ8118001 3DJ8118001 1 7 2 OP1 OP 3 1 3 6 HOLE-V8 8 MBRST7 MBRST6 MBRST5 MBRST4 MBRST3 MBRST2 MBRST1 MBRST0 9 1 7 H1 4 8 2 HOLE-V8 5 8 1 4 3 H2 9 4 1 8 5 9 1 4 5 1 8 9 1 4 1 1 MBRST15 MBRST14 MBRST13 MBRST12 MBRST11 MBRST10 MBRST9 MBRST8 5 EMI Solution 104 Confidential - Do Not Copy PJ513D-1 SSP0_RXD 13 SSP0_CLK 9 SSP0_TXD 9 P3P3V ( DMD I/F ) 9 R158 33 J R157 33 J R156 33 J TP174 MBRST[15:0] 5 R154 OPEN MBRST[15:0] 14 P12V 2 DN12 3 BAT54SW 1 1 DN11 3 BAT54SW 3 BAT54SW 1 DN10 3 1 DN9 BAT54SW 2 2 P12V 2 5,13,14,17 TP175 TP58 11 OCLKA OCLKA 6 37 P12V 11 L33 33U K 10 A 9 CW_PWM U21C VBB3 1 OUTB 15 R160 1 TP59 TP60 TP61 1 VMSW 13 CTAP P3P3V R162 3.3K J 5 SENSE 14 GND GND GND Thermal Pad 44 19 7 G1 PMD1K_SENSE_MOT R164 150 J OUTC_SNUB OUTB_SNUB OUTA_SNUB C301 1000P J C302 1000P J C303 1000P J TP63 TP64 CWSENSOR OPDIODE R168 180 J14 G2 3 2 1 G1 G2 3 2 1 G1 2KL2021003 R170 2K J C304 R172 R173 10K J 330K J 10P J 0.1U K CWINDEXA 9 U23 1 INPUT+ 2 GND 3 INPUT- 0.1U K VCC 5 OUTPUT 4 ADCMP370AKSZ-REEL 2.5VREF R171 10K J CWINDEXA R174 6.8K GND ViewSonic Corporation R165 150 J R167 1.5 F P5V C306 2 105 Confidential - Do Not Copy 1 2KK2084004 R163 150 J TP176 C305 3 CW Y3 3,6,7,8,9,10,11,13,14,15,17 P3P3V 3,4,5,6,7,9,13,17 R169 75K J CW Y2 G1 GMIN C300 0.1U K P5V G2 CW Y1 4 CWCTR PMD1000 TACH 8 R161 16 OUTC TP62 R166 10K J OUTA R159 VM D21 PMEG2020EJ C299 22U K CW_PWM OSC 12 J13 PJ513D-1 3,4,5,6,7,8,9,10,11,12,13,14,15,17 P12V P12V 5,13,14,16 P12V RF1 2.2K E B QF3 QF4 CF4 10K J TP67 FG2 C FG2 QT1 KN3904/P TP68 CT1 B E FAN1 FG1 1 2 7 15 FAN3 FG3 20 19 FAN2 FG2 NC1 NC2 18 17 DXP1 ALERT C C RF6 FAN3 E E RF12 10K J 2SB772S-P-L FAN3 RF9 10K J 0.1U K RF13 1K J FG3 FG3 P5V_A RF14 10K J FAN1_B FAN1_E TP66 FAN2_E FAN2_E 3 4 P12V 0J 2200P K Shape R176 FAN2_B CT2 0J 2200P K Shape R177 8 SGND1 9 DXP2 10 SGND2 G793D5U DGND 5 QF2 B CF6 2N3904S 0.1U K AVCC 10K J FG1 B 22K 2N3904S 6 UF1 FG1 CF5 1U K RF11 QF5 QF6 B P5V_A DVCC RF10 CF1 4.7U Z 180 P5V_A RF8 1K J TP65 C R175 CF3 2N3904S 0.1U K 10K J FAN2_B RF4 5 SCL SDA SCL SDA 14 13 X2 12 RF15 X1/CLK 11 RF16 SCL SDA 9 6,7,9,11 2M J 10M J 16 2N3904S 0.1U K 5 1K J B CF2 RF7 E P5V_A 22K B E RF5 C C 2.2K FAN1 FAN1 RF2 1K J C 2SB772S-P-L RF3 E QF1 CF7 P5V QF8 B RF20 10U K 0.1U K 2N3904S 2N3904S P3P3V 3 2 P5V RF23 1K J SI2315BDS-T1-E3 QF10 GND 3,4,5,6,7,8,9,10,11,12,13,14,15,16 RF21 10K J B RF24 E J16 TP74 J17 G1 1 2 3 G2 TP69 TP70 TP71 TP72 G2 TP73 FG3 FAN3 6 5 4 3 2 1 FG3 FAN3 TP75 G1 2KD2093103 FG1 FAN1 FG2 FAN2 2KD2093106 TP76 Blower Fan ViewSonic Corporation 106 Confidential - Do Not Copy Rear Fan and DMD Fan PJ513D-1 RF22 10K J QF11 2N3904S G1 1 2 3 G2 3,6,7,8,9,10,11,13,14,15,16 3,4,5,6,7,9,13,16 CF11 0.1U K 10K J P5V_A 1 CF10 P3P3V C CF9 QF9 B 3 22K 4 RF19 32.768KHZ Y3 E FAN2 C RF18 C B 1K J E FAN2 10P J C 2SB772S-P-L CF8 10P J 2.2K E QF7 2 1 RF17 FAN1 FG2 FAN2 470 FAN_SW 9 9. PCB Layout Diagrams ViewSonic Corporation 107 Confidential - Do Not Copy PJ513D-1 ViewSonic Corporation 108 Confidential - Do Not Copy PJ513D-1 1 6 4 11 12 9 2 3 8 5 13 7 10 10. Exploded Diagram and Exploded Parts List ViewSonic Corporation 109 Confidential - Do Not Copy PJ513D-1 EXPLODED PARTS LIST (PJ513D-1) ViewSonic Model Number: VS11959 Rev: 1a Serial No. Prefix: QTY Item 1 2 3 4 5 6 7 8 9 10 11 12 13 ViewSonic P/N M-00008166 RLC-035 HW-00008365 C-00008740 C-00008742 C-00008744 C-00008746 M-00008164 M-00008165 B-00008774 B-00008775 B-00008776 B-00008777 Ref. P/N 6E.06001.001 5J.0EB01.001 6K.0EB12.001 6K.0EB06.001 6K.0EB07.001 6K.0EB08.001 6K.0EB09.001 2C.10130.051 2C.10139.031 5E.08040.011 5E.0EB01.001 5E.06023.001 5D.0CY12.001 Description ASSY PL ZOOM MP612 AOCI PACK LAMP RLC-035 ASSY SUB LAMP DOOR WHT PJ513D ASSY UPPER CASE PJ513D ASSY LOWER CASE PJ513D ASSY FRONT COVER PJ513D ASSY REAR COVER PJ513D FAN*2 70*80*25 30MM AD0712MB FAN50*50*20 200MMAB5012HBMP511 PCBA POWER BD MI MP511+ PCBA MAIN BD PJ513D MI 8L PCBA CHIP BD MP612 MI BALLAST 180W 2.5KV EUC180DV11 110 ViewSonic Corporation Confidential - Do Not Copy Q'ty 1 1 1 1 1 1 1 1 1 1 1 1 1 PJ513D-1 Module 2 –ASSY UPPER CASE ViewSonic Corporation 111 Confidential - Do Not Copy PJ513D-1 Module 3 –ASSY LOWER CASE ViewSonic Corporation 112 Confidential - Do Not Copy PJ513D-1 Module 4 –ASSY FRONT CASE Module 5 –ASSY REAR CASE ViewSonic Corporation 113 Confidential - Do Not Copy PJ513D-1 For Worldwide: Remote 1 QSG 10 CD 11 9 2~7 15 14 12 13 ViewSonic Corporation 114 Confidential - Do Not Copy PJ513D-1 For China: Remote 1 QSG 10 CD 11 9 8 15 14 12 13 ViewSonic Corporation 115 Confidential - Do Not Copy PJ513D-1 PACKING PART LIST (PJ513D-1) ViewSonic Model Number: VS11959 Rev: 1a Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ViewSonic P/N A-00008249 A-00008250 A-00008097 A-00008098 A-00008099 A-00008193 A-00008251 A-00008100 CB-00008120 DC-00008708 DC-00008747 P-00008300 P-00008790 P-00008302 P-00008303 Ref. P/N 5F.26J1K.121 2G.01111.001 2G.82718.281 2G.01018.000 2G.01343.001 2G.04321.001 2G.01433.001 2G.04245.001 5K.01207.501 4J.0EB01.001 5B.0EB01.002 4B.01214.001 4D.03A02.021 4G.03A02.001 4G.03A03.001 Location REMOTE RC-7092A-01-0003 PJ513D CORD SVT125V WO/SH US 1.8M I-S CORD H05VV-F 10A250V EUR BLK CORD H05VV-F13A250V 1830MM UK CORD 3ASL/75DU-IN 250V1.8M AUS CORD H05VV 250V 1.8M BLK KOR CORD H05VV 16A 250V 1.5M S-ARF CORD RVV 250V 1.8M BLK CHINA CABLE SIGNAL 15/15P 1.8M+PEBAG GUIDE QS PJ513D CD USER MANUAL PJ513D BAG HDPE+LDPE 415*365*0.4 CTN AB VIEWSONIC/ PJ513D CUSHION LEFT EPE VG30 CUSHION RIGHT EPE VG30 116 ViewSonic Corporation Confidential - Do Not Copy Q'ty 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 PJ513D-1 11. Recommended Spare Parts List RECOMMENDED SPARE PARTS LIST (PJ513D-1) ViewSonic Model Number: VS11959 Rev.: 1a Serial No. Prefix: QTY Item 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 Accessories: [Adapter, Remote Control;Power Cord] PC Board Assembly: [All PCBA] Cabinets: [Front Panel, All Covers, Base Assembly] Cables: [All Cables] Documentation: [Quick Start Guide, Electronic Components: [CRTEEPROM, Fly Back Miscellaneous: [Switch, Fan, Logo] Packing Material: [Box, Foam, Bags] Description ECR/ECN Remote Control - 7092A-01-0003 Replacement Lamp Cord/ Cable-125V WO/SH 1.8M US Cord/Cable 250V Black EUR Cord/Cable 1830MM UK Cord/Cable - 250V 1.8M AUS Cord/Cable 250V 1.8M Black CHINA Cord/Cable 250V 1.8M Black KOR Cord/Cable 250V 1.5M S. AFR PSU - Supply Board MI MP511+ Main Board MI 8L Sub Board- CHIP BD MP612 MI Sub Board (Ballast 180W 2.5KV) Upper Case Assy Upper Case Assy, Black Lower Case Assy Lower Case Assy, Black Front Cover Front Cover Black Back Cover Back Cover, Black Cover - (Sub Lamp Door) - MP510 Cover - (Sub Lamp Door), Black Signal Cable 15/15P 1.8M, +PE Bag Quick Start Guide CD-Rom Pack CW Module Pack LP Module Integrated Circuit DMD 0.55 SVGA Fan *2 70*80*25 30MM Fan 50*50*20 200MM ZOOM Assy, MP612 AOCI Bag Carton Left Foam Right Foam ViewSonic P/N A-00008249 RLC-035 A-00008250 A-00008097 A-00008098 A-00008099 A-00008100 A-00008193 A-00008251 B-00008774 B-00008775 B-00008776 B-00008777 C-00008740 C-00008741 C-00008742 C-00008743 C-00008744 C-00008745 C-00008746 C-00008747 C-00008291 C-00008748 CB-00008120 DC-00008708 DC-00008709 E-00008707 E-00008708 E-00008709 M-00008164 M-00008165 M-00008166 P-00008300 P-00008790 P-00008302 P-00008303 Ref. P/N Location Universal number# 5F.26J1K.121 5J.0EB01.001 2G.01111.001 2G.82718.281 2G.01018.000 2G.01343.001 2G.04245.001 2G.04321.001 2G.01433.001 5E.08040.011 5E.0EB01.001 5E.06023.001 5D.0CY12.001 6K.0EB06.001 6K.0EB06.011 6K.0EB07.001 6K.0EB07.011 6K.0EB08.001 6K.0EB08.011 6K.0EB09.001 6K.0EB09.011 6K.01222.001 6K.0EB12.011 5K.01207.501 4J.0EB01.001 5B.0EB01.001 CS.5J080.001 CS.5J080.011 7A.08060.D00 2C.10130.051 2C.10139.031 6E.06001.001 4B.01214.001 4D.03A02.021 4G.03A02.001 4G.03A03.001 Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items. Remark 2: All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is to eliminate repeated cross checks of each item 117 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1 * Reader’s Response* Dear Readers: Thank you in advance for your feedback on our Service Manual, which allows continuous improvement of our products. We would appreciate your completion of the Assessment Matrix below, for return to ViewSonic Corporation. Assessment A. What do you think about the content of this Service Manual? Unit Excellent Good Fair Bad 1. Precautions and Safety Notices 2. Specification 3. Front Panel Function Control Description 4. Circuit Description 5. Adjustment Procedure 6. Troubleshooting Flow Chart 7. Block Diagrams 8. Schematic Diagrams 9.PCB Layout Diagrams 10. Exploded Diagram and Exploded Parts List 11. Recommended Spare Parts List B. Are you satisfied with this Service Manual? Item Excellent Good Fair Bad 1. Service Manual Content 2. Service Manual Layout 3. The form and listing C. Do you have any other opinions or suggestions regarding this service manual? Reader’s basic dada: Name: Title: Company: Add: Tel: Fax: E-mail: After completing this form, please return it to ViewSonic Quality Assurance in the USA at facsimile 1-909-839-7943. You may also e-mail any suggestions to the Director, Quality Systems & Processes (marc.maupin@viewsonic.com) 118 ViewSonic Corporation Confidential - Do Not Copy PJ513D-1
Similar documents
engine long block
FI, GAS, B18B1(Eng. Desi.), DOHC, NON V-TEC, CRANK ANGLE SENSOR MOUNTS TO OIL PUMP, TIMING GEARS BELT AND TENSIONER INSTALLED FI, GAS, K20A2(Eng. Desi.), DOHC, V-TEC BOTH INTAKE & EXHAUST, CHAIN DR...
More information