Denby Dale Passivhaus specification guide

Transcription

Denby Dale Passivhaus specification guide
Denby Dale Passivhaus
specification guide
1.
specialist Passivhaus/low energy products from Green Building Store
product image
description
more information
Windows & doors
Triple glazing, polyurethane thermal break,
warm edge spacers.
PAUL Thermos 200 MVHR unit.
MVHR unit
Ecopassiv. Uw = 0.75W/m2K, FSC 100% timber.
Heat recovery efficiency of 92%.
Passivhaus Institut certified.
Pro Clima Solitex.
Roofing membrane
Vapour-open airtight underslating membrane.
Pro Clima Rolflex & Kalflex.
Airtightness grommets
For airtightness detailing around cabling and pipework.
Pro Clima Tescon Profil.
Airtightness tape
Flexible multi-purpose corner tape for windows, doors and
corner joints.
Airtightness tape Pro Clima Contega.
(for junctions with plaster)
Vapour resistant timber to plaster sealing tape.
Airtightness adhesive
Pro Clima Orcon F.
Multi-purpose flexible joint adhesive for indoor/outdoor
applications.
Cavity wall ties
Passivhaus
range
TeploTie low conductivity basalt wall ties.
Thermal conductivity (0.7 W/mK). 450mm long.
To see Green Building Store’s
Passivhaus range go to:
www.passivhausproducts.co.uk
www.greenbuildingstore.co.uk
Tel 01484 461705
Denby Dale Passivhaus specification guide
1.
specialist Passivhaus/low energy services from Green Building Store
product image
description
more information
MVHR ducting Lindab steel ducting design and commissioning service.
design service
Design services
Passivhaus Planning Package (PHPP) and
Therm modelling.
Window and door
Advice on positioning of windows and doors within cavity
installation detailing service
wall using plywood boxes.
Aluminium cavity closers
Bespoke solution to need to seal cavities around window
aperture. Powder-coated finish.
product name
more information
Roof insulation
2 x 200mm and 1 x 100mm mineral wool insulation. Knauf loft roll 40.
Cavity wall insulation
3 x 100mm mineral wool batts. Knauf Dri Therm cavity slab 32.
Ground floor insulation
3 x 75mm polyfoam insulation. Knauf polyfoam floorboard.
Sub-ground floor insulation
1 x 300mm polystyrene filled cavity using Styrene Plus Therm.
Inner leaf blockwork
100mm dense concrete block inner leaf.
Outer leaf blockwork
Coursed natural Yorkshire stone.
Foundation inner leaf blockwork
100mm Celcon 7KN lightweight block.
I-Beams
302mm deep timber I-Beam first floor, using Boise Engineered Floor System.
Condensing gas boiler
Vaillant Eco TEC 612 (4.8 kW)
Passivhaus
range
To see Green Building Store’s
Passivhaus range go to:
www.passivhausproducts.co.uk
www.greenbuildingstore.co.uk
Tel 01484 461705
© green building store 2010 design © chris j bailey 2010
standard products obtainable from most UK builders’ merchants

Similar documents

Denby Dale Passivhaus

Denby Dale Passivhaus Uw inst. = 0.8 W/m2K Schematic drawing based on an example from proceedings of the Passive House Conference 2006 for renovation of typical German construction using PH standard window. Freundorfer,

More information

Project sheet - Denby Dale - PASS-NET

Project sheet - Denby Dale - PASS-NET the insulation layer. For more information on the Denby Dale Passivhaus and to register for a free 40 page pdf technical briefing,go to:: www.greenbuildingstore.co.uk/denbydalehouse

More information

Denby Dale Report -Bill Butcher applcation - November 2011

Denby Dale Report -Bill Butcher applcation - November 2011 by fabricating aluminium cavity closers, backed with PUR and powder coated to match the windows and door frames. These were let into a groove in the face of the frame and sealed against the stonewo...

More information