Pro-Series Strobe Kit Instructions

PRO-SERIES ®
All Street Glow products are covered by a comprehensive warranty.
StreetGlow neon products are warranted against defective materials and workmanship for as long as the original purchaser
owns the product. StreetGlow Radio Bars and other non-neon products (excluding fog lights and driving lights, and HID
bulbs) are warranted against defective materials and workmanship for two years from date of purchase. Fog lights and
driving lights, and HID bulbs are warranted for one year from date of purchase. Any product that should fail for either
defective materials or workmanship will be repaired or replaced, at StreetGlow’s option, as the sole remedy of the buyer.
Proof of purchase is required. All warranty claims are to be handled by selling agents. Accident, abuse, neglect,
modifications, broken glass (with the exception of SG201 Undercar Kit), labor, transportation, improper installation and the
use of products other than for their intended purposes are not covered. NEITHER SELLER NOR THE MANUFACTURER
SHALL BE LIABLE FOR ANY INJURY, LOSS OR DAMAGE, DIRECT, INCIDENTAL OR CONSEQUENTIAL
(INCLUDING, BUT NOT LIMITED TO INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR LOST PROFITS,
LOST SALES, INJURY TO PERSON OR PROPERTY OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL LOSS),
ARISING OUT OF THE USE OR THE INABILITY TO USE THE PRODUCT AND THE USER AGREES THAT NO
OTHER REMEDY SHALL BE AVAILABLE TO IT. Before using, the user shall determine the suitability of the product for
the intended use, and user assumes all risk and liability whatsoever in connection therewith.Some states and countries do not
allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights and you may also have other rights, which vary from state to state
and from country to country. DISCLAIMER: THE FOREGOING WARRANTY IS AN EXCLUSIVE WARRANTY IN
LIEU OF ANY OTHER EXPRESS WARRANTIES. ANY IMPLIED WARRANTIES (INCLUDING, BUT NOT
LIMITED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE)
TO THE EXTENT THAT IT COULD APPLY TO ANY OF THE PRODUCTS MANUFACTURED BY THE COMPANY
SHALL BE LIMITED IN DURATION TO THE PERIODS OF THE EXPRESS WARRANTY GIVEN ABOVE.
STROBE SYSTEM
INSTALLATION INSTRUCTIONS
Design and specifications are subject to change without notice.
© StreetGlow, Inc., 2003
streetglow.com
WARNING!
HIGH VOLTAGE
When the unit is turned on the strobe head
outlets contain High Voltage. Please wait
5 minutes after shutting this unit off before
attempting service. Do not plug strobe heads
into the unit while it is running.
1. TECHNICAL SPECIFICATION
INPUT VOLTAGE
CURRENT DRAW
OUTPUT POWER
OUTPUT VOLTAGE
10 to 16 Volts DC
7.75 AMPS
3. SYSTEM LAYOUT
Plan your system layout before starting.
This is a typical system layout.
4. BULB INSTALLATION
7. STROBE HEAD CONNECTIONS
Remove lens
assembly
from vehicle.
Pop the bulb
into the 1”
hole.
1” hole
saw
Plug the strobe head cables into the
output connectors. Additional heads
and extension cables can be
purchased and connected to the two
remaining outlets.
Drill
hole
NOTE: The bulb will get hot during operation.
Keep the bulb glass at least 3/4” away from
any plastic of the lens assembly.
8. POWER CONNECTIONS
Before you make any connections to the vehicle
wiring, always disconnect the battery negative
terminal.
5. INSTALL THE CABLES
80 WATTS
500 VOLTS DC MAX
2. SYSTEM CONTENTS
(1)
6 Outlet 80W power supply
(1)
Main power harness
Route the cable through the vehicle
and plug into the strobe bulbs.
Optional
control
panel interface
Cable
Screw to
chassis ground
Black
(1)
Important!
On/Off switch harness
(1)
(5)
Butt-splice connector
#8 x 1/2” Screws
Clear strobe bulbs
1
15’ extension cables
Red
Butt Splice
RTV
Do not put RTV
on electrical contacts
Power Harness
Connect to a fused
=12V source
On/Off
Switch
harness
Re-connect the negative battery terminal
6. MOUNT THE POWER SUPPLY
Mount the power supply in a clean, dry location. Mounting the
unit to a flat metal surface will aid in heat dissipation.
Four #8 x 1/2” screws are provided...
(4)
(4)
If the bulb is located in a damp area, the connectors should
be sealed with RTV silicone sealant. (Not included)
9. TROUBLE SHOOTING
Blown Fuse: The power supply will blow a fuse if the input voltage is
reversed. If this happens, first locate the wiring fault, then replace the fuse
with one of the same rating.
Erratic behavior (and/or) shutdown:
1) The power supply will shut down if there is a short circuit condition on
any one of the strobe heads. If the electrical conductors connecting the
power supply to the strobe heads are exposed to water, a short circuit will
result. The first sign is intermittent operation, followed by complete
shutdown of the strobe system. To find the short circuit, unplug all strobe
head cables from the power supply. Test one cable/head at a time until the
problem is found.
2) The power supply will also shut down if the input voltage drops below 10
Volts. Check for a bad connection at + and GND, or a bad switch.
2