Seramic Light Coatings is durable and is characterized

SERAMIC® LIGHT COATING
Luminescent coatings
Seramic® Coating Light Luminous coatings can be applied for different purposes. For example as street
marking or for guidance in dark situations. Or as singing in places where no electricity or light sources are
present. For example, recreational markings. Other applications are in public places like railway stations,
theaters, football stadiums and more. In the case of an emergency (fire, smoke-filled rooms, etc.) the
light falls out and people can no longer orient causing panic. The strong initial afterglow effect of the Seramic® Light Coating paint system are very functional and valuable in this case. In addition, the system
loads itself very quickly, which means, that a few minutes, to sunlight or artificial light is sufficient for
more than 6 hours light output
.
Beach cross-over Oosterend/ Terschelling applied with Seramic Lightcoatings.
System for use on Asphalt
Climatic conditions:
The application of two-component products may be made only at a relative
humidity lower than 85% and at a temperature of substrate and / or environment higher than 10 ° C, where in the
temperature of the substrate to be treated 4 ° C must be above the dew point.
Surface:
The surface must be dry, grease-free and clean of sand, mud and other contaminants
Apply primer 38-0139:
The 38-0139 seramic Road 1K Primer is a one component solvent-based primer with excellent adhesion to
bitumen surfaces such as asphalt. Seramic Road Primer is applied airless and has a drying time of about 2 hours
before applying 38-0142 seramic Light Coating on.
Apply Topcoat 38-0142 seramic Light Coating:
38-0142 seramic Light Coating is a poly-aspartic 2K / urethane coating. After mixing of the component A + B the
product has a "pot-life" of about 45 minutes. Seramic Lighcoating can be applied by means of 2-component airless
systems, and by means of a traction machines with an opening of max. 700 Microns. Seramic Light Coating should
be applied at a minimum layer thickness of at least 500 Microns.
Spreading antiskid and glass beads:
38-0142 shall, if necessary or desired, immediately after application to be sprinkled with roughness makers and
glass pearls. Anker Stuy offers the specially appointed pearls 38-0200. Glass Mixture GITD.
Target groups:
- Infrastructure (trails / Bycicle lanes and roads)
- Future: highways
- Public buildings
- Mobility (bike parts)
- Guide elements or prefabricated materials
Seramic Light Coatings can be applied in several sectors and industries and can
install solutions that were previously difficult or hard to install with traditional
cable systems.
Seramic Light Coatings is durable and is characterized by good adhesion to
asphalt and concrete surfaces
Pull-off / Dolly test
- Temp. °C / Rel.Hum. % 23°C / 50% RH
Test speed 1 mm/min
- Grip to grip separation 365 mm
Machine data 1475 WN:115401
The intercoat adhesion between the
38-0139 primer and 38-0142 topcoat is
excellent and the adhesion of the primer
on the asphalt or concrete can also b
ereferred to as excellent.
Emission time:
With the light on
15 minutes after turning off the light
150 minutes after turning off the light
240 minutes after turning off the light
(TNO Report TQS-RAP-08) Commissioned by Anker Stuy Paints
Salt Spray Test
Acetic Acids salt spray test after 500 hours exposure
Acetic Acids salt spray test after 1500 hours exposure
Seramic Lightcoatings
Anker Stuy Verven
Hellingwal 1
8407 EM Terwispel
Nederland
www.ankerstuy.nl
info@ankerstuy.nl
T: +31 (0)513.46.5000