Data sheet_en mx0606-0808

Transcription

Part Number
MX-0606-PP
6 Input 6 Output single cable matrix
with 2 way IR control
Part Number
MX-0808-PP
8 Input 8 Output single cable matrix
with 2 way IR control
Wyrestorm Pro Plus
HDBaseT Matrix Solutions
Instruction Manual
Thank you for choosing this WyreStorm product.
Please read these instructions carefully before installing to avoid complications later.
1
CONTENTS AND INTRODUCTION
Contents
1
Introduction
2
Features
3
Safety Precautions
4
Package Contents
5
Specifications
6
Front Panel Description
7
Rear Panel Description
8
Typical Application
9
Connection
10 Basic Operation
i. Front Panel Control
ii. Remote Control at Matrix end (Local IR) and Battery
Replacement
iii. Matrix System Code Switch – control two matrices with one
handset
iv. Remote Control at the Display End (Remote IR)
v. Handset Output/Source select Key Code
vi. IR call-back control of Matrix and Sources Devices
vii Two-way IR call-back control between Matrix, Sources and
Displays from Multiple Locations
viii. IR Extender Control
11 Advanced Remote Control
12 Advanced Operation
i. RS232 Control
ii. COM CTL – PC software Control
iii. NET CTL – LAN Control
iv. EDID DIP Switch settings
13 Troubleshooting
14 FAQ
15 Maintenance
16 Provided Service
17 Mail In Service
18 Warranty
Warranty Limits and Exclusions
19 Installation Reference Log
20 Notes
2
1.
Introduction
The Wyrestorm PRO PLUS (PP) range uses a 2nd
generation HDBaseT technology to sit comfortably
between our PRO range of matrices and extenders and
flagship HDBaseT products to enable the transmission
of full, uncompressed HD 1080p video and audio, with
discrete 2-way IR control over distances of up to 70m
(131ft) using a single Cat5e/6/7 cable.
The MX0606 / 0808-PP Pro Plus HDBaseT Matrix models
allows any of their 6 or 8 HDMI inputs to be distributed
independently and simultaneously over distances of up
to 70m/230ft to any of the 6 or 8 HD output displays
connected, regardless of HDCP encryption, with discrete IR
control.
While full HDBaseT is intended for high end, high spec
installations over distances of up to 100m/328ft, 70m/230ft
HDBaseT has been specifically developed for small to
mid-range projects that perhaps do not necessitate such a
high specification, long transmission distance, or indeed, a
premium price tag.
This alternative classification of HDBaseT shares many of
the same strengths as the full version, such as a ‘one-cable’
distribution method, the signal stability and resistance to
interference, but it removes the Ethernet distribution and
reduces signalling rate and resolution, while still allowing
fully controllable HD distribution over single cable runs up to
70m/230ft.
As Wyrestorm systems are fully cascadable, maximum
transmission range of the matrix output can be increased
up to a further 7 times by connecting multiple 70m/230ft
HDBaseT extender sets for longer distributions.
Simultaneous HDMI outputs, mirrored to the HDBaseT
outputs allow easy connection to AV receivers or additional
displays, essentially doubling the number of outputs.
Duplicate HDMI also enables non-UTP transmission with
alternative Wyrestorm Extender products such as Coax,
Fibre or full HDBaseT for unrivalled choice and compatibility.
The Pro Plus range offers flexibility and reliability of signal
distribution, with innovative features and an ease of use to
deliver HD audio and video, controlled via IR, RS232 or LAN,
all on a single Cat5e/6/7 cable that removes the need for
additional control and video cables on installations, whether
in a residential or commercial setting.
For further information on this product and other Wyrestorm
ranges, visit our website or download our latest product
guide.
www.Wyrestorm.com
Part Number
MX-0606-PP
Part Number
MX-0808-PP
Technical Support: support@wyrestorm.com US: +866 677 0053 EU: +44 (0) 1793 230 343
2.
Features
• Each output
able to show any connected source simultaneously
regardless of whether the input carries HDCP encryption.
• Refined for Custom Install and Home Theatre Installations.
• Quick and easy installation – set up in seconds straight out of the box.
• Reads and copies EDID from connected devices with additional
EDID configuration through customisable DIP switch settings if
• Simplified ports - Input: HDMI – Output: Simultaneous HDMI and
necessary.
integrated RJ45 connectors for a single Cat5e/6/7 UTP cable to each
• 2k resolution
supported.
display
point for ease
of installation*
• Fully 3D compatible – Frame sequential 3D (Blu-ray) and
* The
inclusion
of duplicate
ports
essentially
doubles the
interlaced
stereoscopic
3DHDMI
(satellite
broadcasts
etc.)
number of outputs (though slaved to the output channel on the
• Supports
all high definition
resolutions
to and
including
matrix),
or allowing
connection
to Coax, up
Fibre
or full
HDBaseT
1080p
and
standard
video
formats.
extender sets for increased flexibility and length of distribution.
specified distance range of product, no electrical
interference, the use of straight cable runs with no bends
or kinks and no patch panels or wall outlets used. Please
be advisedHDBaseT
that theorpresence
anycan
of these
factorsby
in
100m/328ft
50m/164ftof
PRO)
be lengthened
your
installation
may
compromise
bandwidth
and
signal
connecting to multiple 70m extender sets or used with any other
strength. extenders,
For longer
transmission
distances,
RS232
control
Wyrestorm
such
as Coax, full HDBaseT
or Fibre
(distances
and
Ethernet
pass-through,
please
see
our
full
HDBaseT
under perfect transmission conditions*)
or HDBT Lite range of matrices, transmitters, receivers and
sets.
•extender
Each Output
port can be fed to multiple displays (cascaded).
• Supports all high definition resolution
3.
3.
WARNING
WARNING
reduce
theofrisk
fire, electric
To To
reduce
the risk
fire,ofelectric
shock shock
or or
product
damage:
product
damage:
• RS232 port.
• Conforms to IEEE-568B standards.
• Choose from 6 switching modes – infrared remote control, front
panel
buttons,
localsupports
IR, IR call-back,
LAN and RS232.
• Each
HDMI
port also
DVI signals.
• Simple switching remote control included, which can also be
• Enables
to 6a (MX0606-PP)
and 8
(MX0808-PP)
HDMI
learnedupinto
universal remote
handset
to allow
the video/audio
control of
devices
to be
independently
switched
through 6
multiple
devices
from one
handset.
(MX0606-PP) or 8 (MX0808-PP) HDMI displays or projectors for
• Fully compatible for integration with market leading control systems.
uncompressed digital distribution.
• 4 x IR 3.5mm mini-jack ports for each output to link IR from
• Each
output
able to
to control
show any
connected source simultaneously
control
system
display
regardless of whether the input carries HDCP encryption.
• Additional infrared extension port for longer IR connections
•• HDCP
with constant feed to prevent screen dropouts.
HDMIcompliant
v.1.3
• Supports 24Bit Colour depth
• Refined for Custom Install and Home Theatre Installations.
• Signalling rate of 6.75 Gbps
• Reads and copies EDID from connected devices with additional
• Pack comes complete with 1 x 4x4 Matrix with 19” rack
EDID configuration through customisable DIP switch settings if
brackets, 4 x 40m IR receivers with mounting brackets, IR
necessary.
receivers, emitters and a Matrix remote control handset.
features
included
on the as
RX-1UTP-IR-40
•Additional
The same robust
transmission
technology
full HDBaseT that is far
more resistant to electrostatic interference than conventional
• Transmits one-way signal together with the HDMI signal over a
non-HDBaseT distribution.
single Cat5e/6/7 cable.
Receivers
capable
1080p transmissions
up to 40m (131ft)
•• HDMI
v1.4 with
full 3Dofcompatibility
with frame packing/sequential
under
ideal
conditions*
(Blu-Ray) and interlaced stereoscopic (satellite/cable broadcasts).
• For even greater control and fine tuning, each receiver features
• Central RS232 control – fully compatible with all market leading control
a fully adjustable EQ distance range for optimising the
systems with full integration protocols available for AMX, Control 4,
transmission signal.
Crestron, Red Eye, Nevo, RTI, Control FX, Savant, BitWise.
Safety Precautions
Safety Precautions
1.
Do not expose this apparatus to rain, moisture, sprays,
drips or splashes and ensure that no objects containing
1. Do not expose this apparatus to rain, moisture,
liquids are placed on the apparatus, including cups,
sprays, drips or splashes and ensure that no
glasses and vases.
objects containing liquids are placed on the
2. apparatus,
Do not place
this unit
in aglasses
confined
such as
including
cups,
andspace
vases.
enclosed shelving, cabinets or bookshelves. Ensure the
unit is adequately ventilated.
2. Do not place this unit in a confined space such as
3. enclosed
To prevent
the risk
of electric
shock or fire hazard due to
shelving,
cabinets
or bookshelves.
overheating,
not cover the
unit or obstruct ventilation
Ensure
the unit do
is adequately
ventilated.
openings with material, newspaper, cardboard or
thatrisk
mayofrestrict
unit.
3. Toanything
prevent the
electricairflow
shock into
or firethe
hazard
overheating,
not cover
the
unit or such as
4. due
Dotonot
install neardo
external
heat
sources
obstruct
ventilation
openings
with material,
radiators,
heat registers,
boilers
or any device that
produces heat
such as
or computers
newspaper,
cardboard
or amplifiers
anything that
may restrictand do
not place
near
sources of naked flame.
airflow
into the
unit.
5. Unplug apparatus from power supply during lightening
4. Dostorms
not install
near unused
external for
heat
sources
such
or when
long
periods
of as
time.
radiators, heat registers, boilers or any device that
6. Protect the power cable from being walked on, pinched
produces heat such as amplifiers or computers and
or restricted in any way, especially at plug connections.
do not place near sources of naked flame.
7. Only use attachments/accessories specified by the
manufacturer.
5. Unplug
apparatus from power supply during
stormsnon-servicable
or when unused
for -long
periods
8. lightening
Units contain
parts
Refer
all servicing to
service personnel.
ofqualified
time.
6. Protect the power cable from being walked on,
pinched or restricted in any way, especially at plug
connections.
• LAN control – with Control 4 TELNET protocols.
• Wide range, two way discrete IR control between source and display
and vice versa (30 KHz to 56 KHz frequency).
• 2K resolution.
• 36bit Deep Colour (compared to 48bit with Full HDBaseT, and 24bit
PRO).
4
7. Only use attachments/accessories specified by the
manufacturer.
8. Units contain non-servicable parts - Refer all
servicing to qualified service personnel.
• 6.75 Gbps bandwidth range/signalling rate (compared to
10.2Gbps with full HDBaseT).
• 70m (230ft) distance range of matrix/extenders – (compared to
3
FEATURE
• Enables up to 4 HDMI video/audio devices to be independently
switched through up to 4 HDMI displays or projectors for
uncompressed digital distribution.
FEATURES AND SAFETY PRECAUTIONS
• Each Output port can be fed to multiple displays (cascaded).
HDMI to HDMI coupleHDMI
r RP-to HDMI coupler RPMaximum Single Link Range 1080p Deep Colour Maximum Single LinMaxi
k Rangemum1080p
SinglDeepe LiColnkourRange 1080pHD-HD.
Deep Colour HD-HD.
4.4. Package
PackageContents
Contents
PACKAGE CONTENTS AND SPECIFICATIONS
PACKAGE
CONTENTS
AND
SPECIFICATIONS
PACKAGE
CONTENTS
AND
SPECIFICATIONS
PACKAGE
PACKAGE
CONTENTS
CONTENTS
AND
AND
SPECIFICATIONS
SPECIFICATIONS
al copy
al copy
com
com
)
)
/
/ssng
ong
onds,
llnds,
mll RXmivers
RXivers
ay.
ay.
70m)
70m)
70
70
4.
Package
Contents
4.
Package
Contents
Transmi
sPackage
sion di/sMX0808-PP
tance
1080p
signal up to 70m
Transmi/ssion distanceTransmi
1080p
n disitosgnaltance
upUART
to 70mcable
/ 1080p signal up to 70m /
•4.
main
unit
• •1 1
xssi
USB
UART
•MX0606-PP
MX0606-PP
/ MX0808-PP
main
unit
xoUSB
to
cable
Contents
230ft (Under perfect transmission conditions including
straight cable runs with no
electrical interference, bends,
kinks, patch panels or wall
• 1 x IR Extension cable
outlets.) Using Wyrestorm RX5.5. Specifications
Specification
5.
Specifications
5. Specifications
1UTP-IR-70 Display receivers
5. Specifications
behi
n+35°C
d+35°C
each(32output
di+95°F)
splay.
Operating
Temperature
00
to to
to to
+95°F)
Operating
Temperature
(32
•• •MX0606-PP
/ MX0808-PP
Printed
instruction
manual
Printed
instruction
manual main unit
• 1 x USB to UART cable
•• MX0606-PP
/ MX0808-PP
unit unit
instruction
manual
MX0606-PP
/UART
MX0808-PP
main
1 x USB
to
cablemain
• ••Printed
Flash
USB
stick
containing
PC
control
software
and
digital
copy
Flash
USB
stick
containing
PC
control
software
and
digital
copy
• 1 x RS232
to RS485
• Printed
instruction
manualconverter
of
instruction
manual*
of
instruction
manual*
• •Flash
USB
stick
containing
PC control software and digital copy
Printed
instruction
manual
1 x RS232
to RS485
converter
• Flash
stick
containing
PC control
and
digital copy
•of 6instruction
/USB
8 x IR
TX
Emitters (small
sensorsoftware
for Input
source)
manual*
versions
can
be
found
at
www.wyrestorm.com
*downloadable
versions
can
be
found
at
www.wyrestorm.com
•of •*downloadable
Flash
USB
stick
containing
PC
control
software
and
digital copy
6 / 8 x IRmanual*
TX Emitters (small sensor for Input source)
instruction
•*downloadable
6instruction
/ 8 x IR RX
Emitterscan
(larger
sensor
for
Output display)
versions
be
found
at
www.wyrestorm.com
of
manual*
*Downloadable
manual
can be found at www.wyrestorm.com
• ••Matrix
brackets
Matrix
brackets
6 / 8mounting
xmounting
IR RX Emitters
(larger sensor for Output display)
•Matrix
1
x
Wyrestorm
matrix
remote
controlatincl.
battery (size/type:
•• Matrix
mounting
brackets
mountingversions
brackets
*downloadable
can
be
found
www.wyrestorm.com
• ••1
x1 100~240V
AC
Power
cable
power
supply
1
xx 100~240V
AC
Power
cable
power
supply
Wyrestorm
matrix cable
remote
control
incl.
battery (size/type:
3V)
• 1 xCR2025
100~240V
AC Power
power
supply
•• •1
x
100~240V
AC
Power
cable
power
supply
Matrix
mounting
brackets
CR2025
3V)
xIRIR
Extension
cable
x Extension
IR
Extension
cable
• 1•1x11
cable
x stylus
• •11x xIR
Extension
cable
100~240V
AC Power cable power supply
stylus
Range
Range Temperature
Operating
Output Video
Range
Operating
Humidity
Range
Operating
Humidity
Range
Operating
Temperature
Output Video
Operating
Humidity Range
Range
0 to +35°C (32 to +95°F)
HDMI v1.4 with full 3D com5
to
90
%
RH
to
90
%
RH
05
to
+35°C
(32
to full
+95°F)
HDMI
v1.4
with
3D
compatibility
with
Frame
Sequen(no
condensation)
(no
condensation)
5 to
% RH
patibility
withand
Frame
Sequential90
(Blu-ray)
Interlaced
condensation)
tial
(Blu-ray) and
Interlaced
Stereoscoptic
(satellite/cable
Output
Bandwidth
6.75Gbps
Output
Bandwidth
Signalling (no
Operating
HumiditySignalling
Range
5 6.75Gbps
to
90 % RH (satellite/cable
Stereoscoptic
broadcasts)
Rate
Rate Bandwidth Signalling 6.75Gbps
Output
(nobroadcasts)
condensation)
Rate
Input
Video
Signal
0.5-1.0
volts
p-p
Input
Video
Signal
0.5-1.0
volts
p-pTrue HD
AudioBandwidth
Format Supported
DTS-HD,
Dolby
Output
Signalling 6.75Gbps
Audio
Format
Supported
DTS-HD,
Dolby
True HD
Input
Video
Signal
volts
p-p
Rate
Input
Signal
55
volts
p-p
(TTL)
Input
DDC
Signal distance 0.5-1.0
volts
p-p
(TTL)
Max.DDC
Transmission
15m
/ 49ft
– if a longer HDMI
Max.
Transmission
distance 5
15m
/volts
49ft
if a longer HDMI
overDDC
HDMI
connection
is– necessary,
we
Input
Signal
volts
p-p
(TTL)
Video
Signal
0.5-1.0
p-p
Single
Link
Range
Deep
Colour
Maximum
Maximum
Single
Link
Range 1080p
1080p
Deep
ColourColour
1080p
36bit
over HDMI
connection
isDeep
necessary,
we
offer the
Wyrestorm
in-line
Maximum
Link Range 1080p
Deep
Colour
Input
DDCSingle
Signal
5 1080p
volts
(TTL)
offer
the
Wyrestorm
in-line
HDMIp-p
to
HDMI
Transmission
distance
Transmission
distance
1080p
signal
signal
upup
tocoupler
to
70m
70m
/ RP/
HDMI
to HDMI
coupler
RPHD-HD.
230ft
(Under
perfect
trans230ft
(Under
perfect
transTransmission
distance
1080p
signal
up
to
70m
/
Maximum Single Link Range
Deep Colour
HD-HD.
mission
conditions
including
mission
conditions
including
230ft
(Under
perfect
transTransmission distance
1080p
signal
up
to
70m
/no
straight
cable
runs
with
no
straight
cable
runs
with
mission conditions including
230ft
(Under
perfect
transelectrical
interference,
bends,
electrical
interference,
bends,
straight cable runs with no
mission
conditions
including
kinks,
patch
panels
oror
wall
kinks,
patch
panels
wall
electrical
interference,
bends,
straight
cable
runs
with
no
outlets.)
Using
Wyrestorm
outlets.)
Using
Wyrestorm
RXkinks, patch panels or wall RXelectrical
interference,
bends,
1UTP-IR-70
Display
receivers
1UTP-IR-70
Display
receivers
outlets.) Using Wyrestorm RXkinks,
patch
panels
or
wall
behind
each
output
display.
behind
each
output
display.
1UTP-IR-70
Display
receivers
outlets.)each
Using
Wyrestorm
behind
output
display.RX1UTP-IR-70 Display receivers
behind each output display.
Single Cat5e/6/7
Display
Receiver (70m)
In-line HDMI to HDMI
In-line
couplerHDMI to HDMI
coupler
Part Number RP-HD-HD
Single
Cat5e/6/7
Single
Cat5e/6/7
Display
Receiver
(70m)
Display
Receiver
(70m)
Single
Cat5e/6/7
Part
RX-1UTP-IR-70
Number
Max. Transmission distance
Max.
Transmission distance
over Cat5e/6/7
over Cat5e/6/7
Display
Receiver
70m
/ 230ft
– using (70m)
Part
Part
Single
Cat5e/6/7
RX-1UTP-IR-70
RX-1UTP-IR-70
70m
/
230ft
– using
Wyrestorm
RX-1UTP-IR-70
Number
Number
Part
Display Receiver (70m)
RX-1UTP-IR-70
Wyrestorm
RX-1UTP-IR-70
Display Receiver.
Number
Display Receiver.
Part
RX-1UTP-IR-70
35 Watts
(max.)800x600,
VESA:
640x480,
VESA:
640x480,
800x600,
Number
35
Watts
(max.)
1024x768,
1280x1024,
1024x768,
1280x1024,
VESA:
640x480,
100-240V
AC 800x600,
1600x1200,
1920x1200
1600x1200,
1024x768,
100-240V1280x1024,
AC1920x1200
VESA:
640x480,
800x600,
DTV/HDTV:
DTV/HDTV:
440mm
/ 17.3”
(W)
1600x1200,
1920x1200
440mm
17.3”
1024x768,
1280x1024,
480i/576i/480p/576p/720p/
480i/576i/480p/576p/720p/
42mm / /1.6”
(H)(W)
DTV/HDTV:
42mm
(H)(D)
1600x1200,
1920x1200
1080i/1080p
1080i/1080p
340mm/ /1.6”
13.4”
480i/576i/480p/576p/720p/
340mm / 13.4” (D)
DTV/HDTV:
1080i/1080p
238.7
6.7
Kg /(MX0606-PP)
14.8lbs
480i/576i/480p/576p/720p/
204.6
6.7
Kg /(MX0808-PP)
14.8lbs
1080i/1080p
230ft (Under perfect trans- 230ft (Under perfect transtioEmitters
nsEmitters
includingconverter
missensor
sisensor
osensor
n condi
tInput
iOutput
onsOutput
isource)
ncldisplay)
udidisplay)
ng
•• •6
//x mi
8
xxsioIR
TX
(small
for
16
RS232
toRX
RS485
6
8/s8
IR
RX
Emitters
(larger
forfor
xn condi
IR
(larger
•• •6
/x Wyrestorm
8x Wyrestorm
x IR RX
Emitters
(larger
sensor
for
Output
display)
TX Emitters
(small
sensor
for
Input
source)
11
matrix
remote
control
incl.
battery
(size/type:
matrix
remote
control
incl.
battery
(size/type:
st
r
a
i
g
ht
cabl
e
r
u
ns
wi
t
h
no
strai
g
ht
cabl
e
runs
wi
t
h
no
CR2025
3V)
CR2025
3V)
• 1
matrix remote
battery display)
(size/type:
6 x/ Wyrestorm
8 x IR RX Emitters
(largercontrol
sensorincl.
for Output
3V)
•• 1•CR2025
x
stylus
1
x
stylus
ectrical interfermatrix
ence, bends,remoteelectri
cal inincl.
terference,
bends,
1 x elWyrestorm
control
battery (size/type:
• 1CR2025
x stylus 3V)
kinks, patch panels or wall kinks, patch panels or wall
• 1 x stylus
outlets.) Using Wyrestorm RX- outlets.) Using Wyrestorm RX1UTP-IR-70 Display receivers 1UTP-IR-70 Display receivers
behinVideo
d each
output display. behinHDMI
dHDMI
eachv1.4
output
difullfullsplfulla3D3Dy.3DcomHDMI
with
comOutput
v1.4
with
Output
Video
v1.4
with
com•• •1
xx USB
to to
UART
cable
11
RS232
RS485
converter
x RS232
to
RS485
converter
xx USB
to UART
cable
••• 1•1
to
RS485
converter
USB
UART
cable
66
/ RS232
8/ 8
x IR
TX
Emitters
(small
sensor
forfor
Input
source)
x to
IR
TX
Emitters
(small
sensor
Input
source)
• 1 x RS232 to RS485 converter
• 6 / 8 x IR TX Emitters (small sensor for Input source)
• 6 / 8 x IR RX Emitters (larger sensor for Output display)
• 1 x Wyrestorm matrix remote control. (Battery not included)
Output Video
Output Video
Audio
Format
Supported
Audio
Format
Supported
Audio
Format
Supported
Max.
Transmission
distance
Max.
Transmission
distance
over
HDMI
over
HDMI
Max.
distance
AudioTransmission
Format Supported
over HDMI
over HDMI
patibility
with
Frame
Sequenwith
Frame
Sequenpatibility
patibility
with
Frame
SequenHDMI
v1.4
with
full 3D
comtial
(Blu-ray)
and
Stereoscoptial
(Blu-ray)
and
Interlaced
tial
(Blu-ray)
and
Interlaced
patibility with Frame SequenticStereoscoptic
(satellite/cable
broadcasts)
HDMI
v1.4 with
full
3D comStereoscoptic
(satellite/cable
(satellite/cable
tial
(Blu-ray)
and
Interlaced
patibility
with Frame
Sequenbroadcasts)
broadcasts)
Stereoscoptic
(satellite/cable
tial (Blu-ray) and Interlaced
broadcasts)
Stereoscoptic
(satellite/cable
DTS-HD,
Dolby
True
HD
DTS-HD,
Dolby
True
HD
broadcasts)
DTS-HD,
Dolby
HD HDMI
15m
/ 49ft
––
if aTrue
15m
/ 49ft
if longer
a longer
HDMI
connection
is
necessary,
wewe
connection
is
necessary,
15m
/ 49ft
– if aTrue
longer
DTS-HD,
Dolby
HD HDMI
offer
thethe
Wyrestorm
in-line
offer
Wyrestorm
in-line
connection
is necessary,
we
15m
/the
49ft
– if acoupler
longer
HDMI
HDMI
to
HDMI
RPHDMI
to
HDMI
coupler
RPoffer
Wyrestorm
in-line
connection
is necessary,
we
HD-HD.
HD-HD.
HDMI
to HDMI
coupler RPoffer the Wyrestorm in-line
HD-HD.
HDMI to HDMI coupler RPHD-HD.
coupler
coupler
Single Cat5e/6/7
Single Cat5e/6/7
HDMI
Max. Transmission distance Max.70mTraIn-line
/nsmiIn-line
230ft
ssion diHDMI
–stHDMI
ausincengto70mtoHDMI
/ 230ft – usiMax.
ng Trans
coupler
coupler
In-line
HDMI(70m)
to HDMI
Display Receiver (70m) overDisplay
Receiver
coupler
over Cat5e/6/7
Wyrestorm
Cat
5
e/6/7
RX-1UTP-IR-70
Wyrestorm RX-1UTP-I
overR-70Cat5e
RP-HD-HD
RP-HD-HD
Part
Number
Part
Number
In-line
HDMI
to HDMI
RP-HD-HD
Partcoupler
splayNumber
Recei
v
er.
Display Receiver.
Part
PartDiPart
Number RP-HD-HD
RX-1UTP-Idistance
Rdistance
-70 70m70m/ RX-1UTP-IR-70
Max.
Transmission
230ft
––
using
Max.
Transmission
/ 230ft
using
Number
over
Cat5e/6/7
Wyrestorm
RX-1UTP-IR-70
over
Cat5e/6/7 distance Number
Wyrestorm
RX-1UTP-IR-70
Max.
Transmission
70m
/
230ft
–
using
Power Consumption
Power
35 Watts
Consumpt(max.
ion ) 35 Watts (max.) Power Con
over Cat5e/6/7
Power
Consumption
Power
Consumption
over
Cat5e/6/7
Power
Consumption
Power
Supply
Power
Supply
Display
Receiver.
Display
Receiver.
Wyrestorm
RX-1UTP-IR-70
70m
/
230ft
– using
Display
Receiver.
35
Watts
(max.)
35
Watts
(max.)
70Watts
max.
(MX0606-PP)
Wyrestorm
RX-1UTP-IR-70
60Watts
max.
(MX0808-PP)
35
Watts
(max.)
Display
Receiver.
100-240V
ACAC
100-240V
Power Supply
Power
100-240V
Supply AC 100-240V AC Power Sup
Power
Supply
100-240V
Consumption
35
Watts
Dimensions
440mm
/(max.)
17.3”
(W)
Dimensions
440mm
/AC
17.3”
(W)
Vi
d
eo
Format
Supported
VESA:
640x480,
800x600,
Vi
d
eo
For
m
at
Suppor
Vi
t
e
d
d
eo
Format
VESA:
640x480,
Supported
800x600,
VESA:
640x480,
800x600,
42mm
/ /×1.6”
42mm
/ 17.3”
1.6”
(H)
00,
440mm
100mm
Dimensions
440mm
(W)x 340mm
Power Supply
100-240V
AC(H)
340mm
13.4”
(D)(D)
340mm
/ 13.4”
00,
/17.3’’
3.9
x3(H)
13.4’’
42mm
/x //1.6”
Di
m
ensi
o
ns
Di
440mm
m
ensi
o
ns
17.
”
(W)
440mm / 17.3” (WDi) mension
1024x768,
1280x1024,
1024x768,
1280x1024,
1024x768,
1280x1024,
Dimensions
440mm
/
17.3”
(W)
0
340mm
/14.8lbs
13.4”
(D)
Weight
6.7
Kg
/
Weight
6.7
Kg
/
14.8lbs
42mm / 1.6” (H)
0
42mm
1.14.8lbs
6” (H)(D) 42mm / 1.6” (H)
Weight
6.7
Kg // /1920x1200
340mm
13.4”
1600x1200,
1920x1200
1600x1200,
1920x1200
1600x1200,
720p/
BTU
Rating
Weight
720p/
Weight
6.7
Rack
Space Required
2UKg / 14.8lbs
Weight
340mm
/ 13.4” (D) 340mm / 13.4” (D)
DTV/HDTV:
DTV/HDTV:
DTV/HDTV:
Technical
Support:
677
0053
EU:
+44
(0)
1793
343
Technical
Support:
support@wyrestorm.com
+866
0053
EU:
+44
(0)
1793
343
55
480i/support@wyrestorm.com
576i
/480p/576p/720p/ US:US:+866
480i677/576i
/480p/576p/720p/
480i
/576i230/230
480p/576p/720p/
Technical
Support: support@wyrestorm.com US: +866 677 0053 EU: +44 (0) 1793 230 343
4
5
Weight
Wei6.7ghtKg / 14.8lbs 6.7 Kg / 14.8lbs Weight
.com US: +866 677 0053 EU: +44 (0) 1793 230 343
1080i
/
1080p
1080i
/
1080p
1080i
/1080p
Support:
US: +866 677 0053 EU: +44 (0) 1793
230 343
.com US:5+866 677 0053 Technical
EU: +44 (0)
1793 support@wyrestorm.com
230 343
Power
Consumption
Format
Supported
Video
Video
Format
Supported
Power Consumption
Video
Format
Supported
Power
Supply
Power Supply
Video
Format Supported
Dimensions
Dimensions
1
Front Panel
4
LED Input/Output Select Screen
2
3
Output Select Buttons (Left/Right)
5
IR Receive Window
Enter Selection Buttons
6
Input Select Buttons (UP/DOWN)
FRONT PANEL AND REAR PANEL
6.
Rack Brackets
3
6
1
4
2
ENTER
4
5
6
3
16 IR TX Receiver ports (corresponds to input ports)
Input/Output port grouping indicator
HDBT OUT
HDMI IN
IR RXH
RJ45 + RS285 DEFINITION
1
2
7
TX+
TXRX+
RJ45 PIN
DESCRIPTION
9
DMI OUT
HDBT OUT
HDMI IN
IR RXH
DMI OUT
HDBT OUT
DMI OUT
HDMI IN
IR RXH
HDBT OUT
HDMI IN
IR RXH
HDBT OUT
DMI OUT
HDBT OUT
DMI OUT
HDMI IN
10
RS485
LAN
14
13
IR EXT
EDID
11
12
8
RX-
RS232
ON
OFF
DEFAULT
1 23
4
15
1
0
IR TX
16
123456
RJ45 + RS285 DEFINITION
1
2
7
TX+
TXRX+
RJ45 PIN
DESCRIPTION
HDBT OUT
HDMI OUT
HDMI IN
IR RX
HDBT OUT
HDMI OUT
HDMI IN
IR RX
HDBT OUT
HDMI OUT
HDMI IN
7
6
5
HDMI OUT
HDBT OUT
8
1 2 3GROUP4 5 6
HDMI IN
HDMI OUT
HDMI IN
HDMI OUT
7
6
5
IR RX
4
8
1 2 3GROUP4 5 6
MX-0808-PP
IR RX
3
HDMI IN
2
IR RX
1
HDBT OUT
Part Number
IR RXH
4
HDBT OUT
3
HDMI OUT
2
HDMI IN
1
MX-0606-PP
IR RX
Part Number
HDBT OUT
8
15 EDID switch default diagram
Power switch
DMI OUT
7
14 EDID DIP Switch (for manual EDID setting)
Fuse (lift cover to replace)
HDMI IN
6
AC 100 – 240V power input
IR RXH
5
12 RS232
13 IR Extension port (IR EXT)
IR Receiver port (IR RX)
HDBT OUT
4
11 RJ45 to RS485 definition indicator
HDMI Input ports
HDMI OUT
3
RS485 port
10 LAN port
Duplicate HDMI Output ports (mirrors HDBT Outputs)
HDMI IN
2
9
HDBT Output ports (RJ45 Cat5e/6/7)
IR RX
1
Rear Panel
IR RX
7.
9
RS485
13
IR EXT
10
LAN
14
EDID
11
12
8
RX-
RS232
ON
OFF
DEFAULT
1 23
4
15
1
0
IR TX
123456
16
RS232 and LAN ports are for matrix control. Ensure crossover UTP cable is used to connect the LAN directly to a
computer or server, and a direct/straight through connection is used to connect via a router/switch. Connection
will fail if the incorrect cable is used.
5
TYPICAL APPLICATION,
TYPICAL
APPLICATION CONNECTION
8.
8.
KEY
Typical Application
Application
Typical
IRTX Emitter
IRRX Receiver
HDMI
Control
System
UTP Cat5e/6/7
Power
MX0808-PP only
MX0808-PP only
Blu-ray/DVD
RX-1UTP-IR-70
Mirror of 01
Output 01
70m/230ft
Apple
TV/Media
Server
RX-1UTP-IR-70
Mirror of 02
Output 02
70m/230ft
RX-1UTP-IR-70
Mirror of 03
PS3/Xbox
Output 03
70m/230ft
RX-1UTP-IR-70
Mirror of 04
Cable/Satellite
Output 04
70m/230ft
Blu-ray/DVD
RX-1UTP-IR-70
Mirror of 05
Output 05
70m/230ft
Apple TV/Media Server
RX-1UTP-IR-70
Mirror of 05
Output 06
70m/230ft
MX0808-PP only
RX-1UTP-IR-70
Mirror of 07
Output 07
Cable/Satellite
70m/230ft
PS3/Xbox
RX-1UTP-IR-70
Mirror of 08
Output 08
70m/230ft
Cat 5e/6 cable performance
5m
10m
15m
20m
25m
30m
35m
40m
45m
50m
60m
70m
80m
196ft 229ft
262ft
HDBaseT Lite range
1080p
MX0606-PP / MX0808-PP with RX-1UTP-IR70 display receiver
16ft
1080p
32ft
49ft
65ft
82ft
98ft
114ft
131ft
147ft
164ft
1080i
signal cut out
Cat 5e/6 wiring guide
6
7
The quality of termination for every RJ45 is essential.
Poor termination leads to
intermittent
performance
and longer
install
times.230 343
Technical Support: support@wyrestorm.com
US:
+866 677
0053 EU:
+44 (0)
1793
Technical Support: support@wyrestorm.com US: +866 677 0053
EU: +44 (0) 1793 230 343
HDMI
Source
HDMI
Source
HDMI Source
KEY
KEY KEY
0101
01
IRTX
Emitter
IRTX Emitter
IRTX
Emitter
IRRX
Receiver
IRRX
Receiver
IRRX
Receiver
0303
optional optional
optional
HDMI
HDMIHDMI
03
UTP
Cat5e/6/7
UTP Cat5e/6/7
UTP
Cat5e/6/7
IR IR
RXRX
jack
plugged
intointo
IR RX jack plugged into
jack
plugged
IR IR
RXRX
port
of matrix
with
IR
RX port of matrix withIR IR
port
of matrix
with
TXTX
emitter
securely
IR TXplaced
emitter
placed
securely
emitter
placed
securely
0202
02
receiver
placed
in clear
receiver placed in clear over
receiver
placed
in clear
input
device
infrared
over
input device
infrared
over
input
device
infrared
sight
of remote
control
sight of remote control sensor
sight
of remote
control
window
sensor window
sensor
window
0404
04
Power
Power
RS485
LAN
Control
System
RS485
LAN Control
System
RS485
LAN
Control
System
TELNET
(Additional (Additional
(Additional
viavia
control via control
control
RS232)
RS232)
RS232)
Power
RS232 to
display
(optional)
CatCat
5e/6/7
(up(up
to
230ft)
Cat 5e/6/7
(up 70m
to 70m
230ft)
5e/6/7
to
70m
230ft)
0808
TYPICAL APPLICATION
Connection
Connection
9.9. Connection
9. Connection
Connection
Connection
9.
RS232
to to
RS232
display
display
(optional)
(optional)
08
0505
05
0606
06
07
Display
1 Mirror
Display
1 Mirror
Duplicate
HDMI
Duplicate
HDMI
1
Display
Display
1 Mirror1 1
Display
Duplicate HDMI
1 receiver
IR Display
RXRX
receiver
IR IR
TX
emitter
IRand
RX and
receiver
and
IRemitter
TX emitter
IR
TX
placed
discretely
thethe
display
with
a aa
placedon
discretely
ondisplay
the display
with
placed
discretely
on
with
clear
lineline
of sight
to of
the
remote
line
toremote
the remote
clear
ofclear
sight
tosight
the
handset
being
used
handset
being used
handset
being
used
0707
mains
or or
5V mains5V
or 5V
mains
USB
power
USB power
USB
power
adapter adapter
adapter
0101Connect
each
HDMI
input
source
(such
as:source
HD-DVD,
01
Connect
each HDMI
input
(such as: PS3/,
HD-DVD,
Connect
each
HDMI
input
source
(such
as:
HD-DVD,
PS3/,PS3/,
HINT
HINT
HINT
Locate
thethe
infrared
devices
byby
shining
a a
Locate
the infrared
sensor
on sensor
devices
by on
shining
a
Locate
infrared
sensor
on
devices
shining
Connect each HDMI input source (such as: HDreceive an IR
signal.
XBOX360,
satellite/cable,
Blu-Ray
etc.)
to to
the
HDMI
XBOX360,
satellite/cable,
Blu-Ray
etc.)
toinputs
theinputs
HDMI inputs
XBOX360,
satellite/cable,
Blu-Ray
etc.)
the
HDMI
flashlight
onto
thethe
display
panel
sources
look
forfor
a a
flashlight
onto
the
display
panel
of sources
andoflook
for
a and
flashlight
onto
display
panel
of
sources
and
look
DVD, PS3/, XBOX360,
satellite/cable,
Blu-Ray etc.) to the
of of
thethe
MATRIX.
of the MATRIX.
MATRIX.
small
sensor.
small
sensor.
small
sensor.
HDMI inputs of the MATRIX.
NOTE Make sure the IR jacks are in the same
ATTENTION
ATTENTION
ATTENTION
DoDo
Not
Hotswap
Plugs!
Please
insert
and
Do
Not Hotswap
Plugs!
Please
insert and 04
Not
Hotswap
Plugs!
Please
insert
and
a good
quality,
well
terminated
5e/6/7
cable
04Connect
Connect
a good
well
terminated
Catterminated
5e/6/7 cableCatCat
04
Connect
a quality,
good
quality,
well
5e/6/7
cable
number
ports.
extract
cables
carefully
with
thethe
power
SWITCHED
OFF.
extract
cables
carefully
withSWITCHED
the power SWITCHED
extract
cables
carefully
with
power
OFF.OFF.
with
an
RJ45
connector
wired
to
568B
standard
at
both
with
an
RJ45
connector
wired
to
568B
standard
at
both
with
an
RJ45
connector
wired
to
568B
standard
at
both
Attention Do
Not Hotswap plugs! - Please
Connecting
and
disconnecting
thethe
unit
is is
powered
Connectingwhile
andwhile
disconnecting
while
thepowered
unit is powered
Connecting
and
disconnecting
unit
ends
from
HDBT
Output
port
oftoof
the
MATRIX
to to
thethe
UTP
ends
from
thethe
HDBT
Output
portOutput
of the MATRIX
thethe
UTP
ends
from
the
HDBT
port
MATRIX
UTP
insert and extract
cables
carefully
with
the topower
HINT Locate the infrared sensor on devices by
can
result
in in
damage
tocan
circuitry.
result
in damage
circuitry.
can
result
damage
to
circuitry.
INININ
of
theRX-1UTP-IR-70
RX-1UTP-IR-70
(or,(or,
if using
of of
the
DISPLAY DISPLAY
RECEIVER
(or,RECEIVER
if using
the
RX-1UTP-IR-70
DISPLAY
RECEIVER
if using
SWITCHED OFF. Connecting and disconnecting
shining a flashlight
onto
the
display
panel
oftransmitter
another
Wyrestorm
extender
connect
to to
another
Wyrestorm
extender
set,
connectset,
theset,
transmitter
to thethe
another
Wyrestorm
extender
connect
transmitter
0202Attach
thethe
IRIR
TXTX
emitters
directly
over
thethe
infrared
02 Attach
the IR TX
emitters
directly
over receiving
the receiving
infrared receiving
Attach
emitters
directly
over
infrared
while powered can result in damage to circuitry.
sources and
look
for
a
small
sensor.
the
matrix
thethe
HDMI
port)
the
matrix
viavia
thevia
HDMI
OUT
port)OUT
the
matrix
HDMI
OUT
port)
sensor
of of
each
input
source
thethe
adhesive
backing.
sensorusing
of each
input
source
using the
adhesive
backing.
sensor
each
input
source
using
adhesive
backing.
You
may
need
to to
adjust
the
position
thethe
You
mayposition
need toof
adjust
theemitter
position
ofafter
theafter
emitter after
You
may
need
adjust
the
of
emitter
2 Attach theinstallation
4moving
Ensure
both
RJ45
connectors
areare
pushed
securely
into
Ensure
both
RJ45
connectors
are
pushed
securely
into
Ensure
both
RJ45
connectors
pushed
securely
into
IR
TX emitters
directly
over
the
infrared
Connect
a good
quality,
well
terminated
Cat
5e/6/7
to to
achieve
thethe
best
results.
Sometimes
the
installation
toresults.
achieve
the
best results.moving
Sometimes
installation
achieve
best
Sometimes
moving
the the
each
port
and
supported
by
the
connector
strain
relief
clipclip
to to
each
port
and
supported
by
the
connector
strain
relief
clip
to
each
port
and
supported
by
the
connector
strain
relief
receiving sensor
of each
inputareas
source
using
the
adhesive
cable
sensor
to to
different
of
the
source
facia
can
improve
sensor
to
different
areas
of the
source
facia canIR
improve
sensor
different
areas
of
the
source
facia
can
improve
IR IR with an RJ45 connector wired to 568B standard at
prevent
them
from
becoming
loose.
The
quality
of
termination
prevent
them
from
becoming
loose.
The
quality
of
termination
prevent
them
from
becoming
loose.
The
quality
of
termination
performance.
performance.
performance.
backing. You may
need to adjust the
position of the
both ends from the HDBT Output port of the MATRIX to
forforfor
your
RJ45
is essential.
quality
lead
to to
youryour
RJ45
is essential.
Poor qualityPoor
terminations
leadterminations
toterminations
RJ45
is essential.
Poor
quality
lead
emitter after installation to achieve the best results.
the UTP IN of the RX-1UTP-IR-70 DISPLAY RECEIVER
intermittent
performance
longer
install
times.
intermittent
performance
and longerand
install
times.
intermittent
performance
and
longer
install
times.
Plug
thethe
3.5mm
jack
of of
the
IR
TX
emitter
Plug
theIR
3.5mm
jack
of theinto
IRinto
TXthe
emitter
Plug
3.5mm
jack
the
TX
emitter
the into the
Sometimes moving the sensor to different areas of the
(or, if using another Wyrestorm extender set, connect the
corresponding
number
IRcorresponding
TXTX
port
on
thethe
rear
panel
the
number
IR
TXrear
port
on theofrear
panel
corresponding
number
IR
port
on
panel
of
the of the
source facia can improve IR performance.
transmitter to
theAlthough
matrix
via
the
HDMI
OUT
port)
HINT
HINT
HINT
Although
allall
Wyrestorm
areare
tested
using
all Wyrestorm
products
areproducts
tested
using
Although
Wyrestorm
products
tested
using
MATRIX.
MATRIX.
MATRIX.
Cat5e
standard,
wewe
suggest
Cat6
asas
thethe
preferred
Cat5e
asasstandard,
we suggest
using
Cat6 asusing
theusing
preferred
Cat5e
as
standard,
suggest
Cat6
preferred
0303ForFor
two-way
IRIR
controlling
thethe
display
matrix
03 emitter
For two-way
IRdisplay
controlling
thethe
display
from
the
matrix bothcable
two-way
IR
controlling
from
the
matrix
due
toimproved
itsits
improved
capabilities.
cable
due
to
its
distribution
capabilities.
cable
due
to
improved
distribution
capabilities.
Plug the 3.5mm
jack
of the
TX
into
thefrom
Ensure
RJ45
connectors
aredistribution
pushed
securely
into
side:
Plug
thethe
3.5mm
jack
ofPlug
thethe
IR3.5mm
RXRX
receiver
thetheinto the
side:
the
jack
of the IR into
RXinto
receiver
side:
Plug
3.5mm
jack
of
IR
receiver
corresponding number IR TX port on the rear panel of the
each port and supported by the connector strain relief
corresponding
IRIR
RXRX
port
onon
thethe
rear
the
MATRIX,
corresponding
IRrear
RXpanel
port
onoftheof
rearthe
panel
of the MATRIX,
corresponding
port
panel
MATRIX,
If Ifusing
Duplicate
display
toThe
thethe
HDBT
Output,
aaDuplicate
display
mirrored
to mirrored
theloose.
HDBT Output,
Ifusing
using
afrom
Duplicate
display
mirrored
to
HDBT
Output,
MATRIX.
clip to prevent
them
becoming
quality
ensuring
thethe
receiver
is placed
in
view
to into
receive
IR IRan IR
theclear
receiver
is placed
clear
viewan
to receive
ensuring
receiver
isensuring
placed
in
clear
view
receive
an
connect
display
the
HDMI
OUT
port.
connect
thethe
display
via the via
HDMI
OUT
port.
connect
the
display
via
the
HDMI
OUT
port.
of termination
for your RJ45 is essential. Poor quality
signal.
signal.
signal.
ATTENTION
ATTENTION
ATTENTION
WeWe
strongly
recommend
using
thethe
We strongly
recommend
using
the
strongly
recommend
using
3 For two-way IR controlling the display from the
terminationssupplied
lead
to
intermittent
performance
andMATRIX
longer
mounting
toMATRIX
secure
thethe
supplied
mounting
bracketsbrackets
tobrackets
secure the
supplied
mounting
to
secure
MATRIX
NOTE
NOTE
NOTE
Make
sure
thethe
jacks
inthe
the
same
matrix side: Plug
the 3.5mm
jack
ofIR
the
IRare
RX
receiver
install
Make
sure
IRthe
jacks
are innumber
thenumber
same
number times.and
Make
sure
IR
jacks
are
in
same
the
accompanying
TRANSMITTER
& DISPLAY
and
thethe
accompanying
TRANSMITTER
& DISPLAY
and
accompanying
TRANSMITTER
& DISPLAY
ports.
ports.
ports.
into the corresponding IR RX port on the rear panel of the
RECEIVER
baluns.
Any
sudden
of of
these
RECEIVER
baluns.
Any sudden
movement
ofmovement
these
RECEIVER
baluns.
Any
sudden
movement
these
MATRIX, ensuring the receiver is placed in clear view to
HINT Although all Wyrestorm products are tested
88
Technical
Support:
US:
+866
677
0053
+44
(0)
1793
230
343
Technical
Support: support@wyrestorm.com
US:+866
+866
677
0053
EU:EU:
+44
(0)
1793
230
343
Technical
Support:
US:
677
0053
EU:
+44
(0)
1793
230
343
8
7
TYPICAL APPLICATION, BASIC OPERATION
using Cat5e as standard, we suggest using Cat6 as
the preferred cable due to its improved transmission
capabilities.
If using a Duplicate display mirrored to the HDBT Output,
connect the display via the HDMI OUT port.
ATTENTION We strongly recommend using the
supplied mounting brackets to secure the MATRIX
and the accompanying TRANSMITTER & DISPLAY
RECEIVER baluns. Any sudden movement of these
devices could lead to loss of picture and sound if
connections become loose or strained, resulting in
unnecessary service call backs.
the first functions to fail.
If you do not have IR control:
• Check your cables are straight with jacks firmly
connected to ports.
• Check your IR sensors are unobstructed and able to
receive infrared signals.
• Check direct sunlight on the emitters/receivers is not
affecting the infrared signal.
10.
Basic Operation
5
Connect the HDMI OUT of the DISPLAY RECEIVER
to the HDMI IN of the display.
6
Plug the 3.5mm jack of the IR RX receiver into the
IR RX port of the display receiver balun. Place the IR RX
receiver sensor discretely on the front of the display with
care taken to achieve a clear line of sight with the remote
control to be used.
For two-way IR controlling the display from the matrix
end: Plug the 3.5mm jack of the IR TX emitter into the
corresponding IR TX port on the display receiver, ensuring
the emitter is placed directly over the infra-red receiving
sensor of the display using the adhesive backing.
Again, adjustment of receiver and emitter position may be
needed to achieve the best IR signal distribution.
The Wyrestorm MX0606/0808-PP is designed with ease
of set-up and use in mind. Basic switching of source
inputs to output displays can be achieved via the front
panel control of the matrix.
On power up, the front panel will flash as the matrix
initialises. When the display stops flashing, the matrix is
ready to use.
7
OUTPUT selection
INPUT selection
8
OUTPUTS are selected by pressing the LEFT and
RIGHT arrow buttons to scroll forwards and backwards
numerically through the displays connected to the matrix.
The corresponding OUTPUT channel number will blink on
the display when reached.
After ensuring the display receiver
balun is fixed firmly in place behind the
display, insert the 5v mains power adaptor
(included) or connect the USB to 5v
power cable.
Switch on the power to your input sources, displays,
and any display receivers used.
Finally, switch on the matrix at the rear and your
Wyrestorm system should now be fully connected and
ready for use.
ATTENTION Remember, always switch off the matrix
before unplugging any inputs or outputs – follow
last on, first off protocol.
If your IR emitters and receivers are correctly placed you
should now be able control both sources and displays
discretely from either location.
ATTENTION If there is electrical interference or
cable bends/kinks within the set up the IR is one of
8
Confirm OUTPUTS/INPUTS
Likewise, the UP and DOWN arrow buttons scroll
numerically through any INPUT sources connected to
the system. When the desired OUTPUT and INPUT is
reached, push the ENTER button to confirm the selection.
The display will stop blinking to let you know the matrix
has been set.
Repeated pressing of the select button of a specific
output scrolls numerically through the HDMI input devices
connected to the matrix, with the corresponding LEDs
illustrating when a device has been selected for that
particular output. The chosen input will automatically
store for the output so, even when the matrix is powered
off and on, the last selected input/output combination will
remain.
OUTPUT
OUTPUT
CHANNEL
CHANNEL
6
6
7
7
8
8
System Code
SwitchCode Switch
System
INPUT SELECT
INPUT SELECT
1
1
The default system setting is 0x00 to control one matrix, but
default
ison0x00
to control
one matrix,
AsThe
such,
thesystem
function
of the
handset
buttons
and but
pressing
the
SYSTEM
CODEsetting
button
the
handset
THREE
OUTPUT
INPUT
SELECT
pressing
the
SYSTEM
CODE
button
on
the
handset
THREE
TIMES
rapidly activates
alternative Matrix
SYSTEMthe
CODE
operation
differsthedepending
onCHANNEL
where
handset
is being
OUTPUT
INPUT
SELECT
TIMES
rapidly
activates
the
alternative
Matrix
SYSTEM
0x4e, allowing independent control of a second unit. Pressing the CODE
To change handset
CHANNEL battery
used.
1
three times
again
to reverts back
to default
setting.
allowing
independent
control
of a 0x00
second
unit. Pressing the
To change handset battery button0x4e,
2
2
3
3
4
4
56
2
67
System Code Switch System Code Switch
78
8
mntrol
setting
oneismatrix,
0x00 but
to control one matrix, but
the
EM handset
CODE button
THREE
on the handset THREE
Matrix
vates SYSTEM
the alternative
CODE
Matrix SYSTEM CODE
ependent
second unit.
control
Pressing
of a second
the
unit. Pressing the
to
again
default
to reverts
0x00 setting.
back to default 0x00 setting.
Basic Remote Control
BASIC REMOTE CONTROL
1
5
3
4
Pinch here and pull out
5
6
Install
‘+’side
side up
Install battery
battery ‘+’
and
onlyonly
use
CR2025 3v
up and
use
7a CR
battery.
compartment
2025
3VSlide
batteries.
Slide
Install
battery
‘+’
side
8handset.
compartment
back
into
back
into
the
up and only use CR
button three times again to reverts 2back to default 0x00 setting.
In the
eventthe
that
two MX0606/0808-PP
NOTE
Changing
System
Code is only necessaryunits
if youare
used
BASIC
BASIC REMOTE
REMOTE CONTROL
CONTROL
11.
BasicRemote
Remote
Control
11.
Remote
Control
11. Basic
Basic
Control
INPUT SELECT
5
5
within
close
proximity,
the close
matrix
are using
two
identical
units
range
of
the necessary
IR of switching
NOTE
3 isiscapable
Changing
thewithin
System
Code
only
if you
signal.
If
using
in
different
parts
of
the
same
room
it
is
between
System
Codes
to likely
allow
control
are usingtwo
twodistinct
identicalIRunits
within
close range
of
the
IR of
OUTPUT
INPUT SELECT
that you will not need to change the setting.
4
CHANNEL
either
matrix
individually
theofsame
hand-set.
signal.
If using
in differentvia
parts
the same
room it is likely
that you will not need to change 1the setting.
HINT If your remote control is not working,5before changing the
Changing the System Code of the handset to that
battery, try changing the System Code on the
in case it
26 handset
assigned
a specificcontrol
matrixiswill
allow IR before
commands to
HINT If to
your
not working,
has accidentally
been remote
switched to an alternative
matrix control changing the
be
delivered
to
only
that
unit.
mode.battery, try changing the System Code
37 on the handset in case it
11. Basic Remote
Control
has accidentally
been switched to an alternative matrix control
48 to control one matrix,
The
default system setting is 0x00
mode.
but pressing the SYSTEM CODE
5 button on the handset
only
the System
necessary
Code
if you
is only necessary if you
System C
the handset.
When
controlling
the matrix
remotely
from thethe
display
side, the Matrix
THREE
TIMES
rapidly
activates
alternative
OUTPUT
INPUT
SELECT
2025
3V batteries.
Slide
ose
ntical
range
unitsofwithin
the IRclose range of the IR
OUTPUT
OUTPUT
CHANNEL
matrix
automatically
detects
which
particular
output
location
INPUT
SELECT
INPUT
SELECT
Switch
RemoteSystem
Control
at
the
Display
End
(Remote IR)control of
6independent
SYSTEM
CODECode
0x4e,
allowing
CHANNEL
CHANNEL
different
sameINPUT
room
parts
it is
of likely
the same room it is likely
compartment back into
SELECT
the user is at and only allows the selection of sources 1-8 for
1be accessed via the
same
basic switching
functions
canthe
also
TheThe
same
basic
switching
functions
can
also
be
accessed
a
second
unit.
Pressing
the
button
three
times
to
need
etting.
to change
the
setting.
handset.
When controlling
the1the
matrix remotely
thehand
displayagain
side, the
that particular
location using
button
thesystem
right
7 - from
1 default
The
setting
is
0x00
to control one ma
remote control.
OUTPUT
OUTPUT
2
via the remote control.
reverts
back
to default
0x00
setting.
matrix
detects
which
particular INPUT
outputSELECT
location
INPUT SELECT
button
will be automatically
deactivated.
11. Basic Remote Control
Remote Control at the Display End (Remote IR)
pressing the
SYSTEM CODE button on the handset
CHANNEL
The default
system
to control one matrix,2but CHANNEL
Operation
ofbefore
the handset
is the
same regardless
of location
– setting is 0x00
8
2 selection
the
user is at and only allows TIMES
the
of sources
for Matrix SYSTE
mote
king,control
beforeischanging
not
working,
the
changing
the
3
rapidly
activates
the 1-8
alternative
The
same
basic
switching
functions
can
also
be
accessed
via
the
For
example,
if
you
are
in
the
Master
Bedroom
with
a
display
pressingreceiver).
the SYSTEM CODE button on the handset THREE
locally
(source/IR
emitter)
orisitremotely
(display/IR
on
ng the handset
System
Code
in case
on
itthe
handset
in case
OUTPUT
that
particular
location
using
the
button
the
right
hand
1
Operation
of
the
handset
the
same
regardless
of
NOTE
Changing
the
System
Code
is
only
necessary
1
allowing
to
output
3 of battery
theCODE
the0x4e,
output
zone isindependent control of a second unit
To change
handset
remote control.
TIMES
rapidly activates theconnected
alternative
Matrix
SYSTEM
3matrix,INPUT
3SELECT
4
een
ternative
switched
matrix
toSimply
control
an alternative
matrix
control
willCHANNEL
be
deactivated.
through
the
INPUTemitter)
sources OUTPUT
connected
to the
location
–toggle
locally
(source/IR
or0x4e,
remotely
(display/
if button
you
using
two units
within
range
of the
button
threeclose
times
again
to reverts
back toSystem
default C0
automatically
detected
so Pressing
options
1-8
correspond
to sources
allowing
independent
control
of a are
second
unit.
the will
INPUT
SELECT
To change handset battery
CHANNEL
Operation
of
the
handset
is
the
same
regardless
of
location
–
2
2
matrix
by
pressing
the
left/right
arrow
buttons
in
each
numbered
5
1-8
on
the
matrix.
Press
buttons
1-8
to
scroll
through
your
1
4setting.
4 parts
IR receiver).
IRFor
signal.
If ifusing
inindifferent
of the
button three times again to reverts
back
to default
0x00are
OUTPUT
OUTPUT
example,
you
the Master
Bedroom
with same
a display
INPUT(source/IR
SELECT
INPUT SELECT
NOTE
locally
or remotely (display/IR
receiver).
OUTPUT
section
onemitter)
the handset.
Changing the System Code is only neces
1
options
as you
channels
onyou
a regular
remote.
HANNEL CHANNEL
OUTPUT
room
it would
is likely
that
willTV
not
need
to
change
the
6
connected
to2 output
3
of
the
matrix,
the
output
zone
is within
INPUT
3SELECT
5 if you 3The
are
using
two
identical
units
close range
o
5 default
CHANNEL
NOTE Changing the System Code is only necessary
system
setting
is 0x00 to control
one ma
Simply
toggle
through
the
INPUT
sources
connected
to
the
toggle
through
the
INPUT
sources
connected
to
setting.
2
Remote
at1the Display
IR)Simply
End
(Remote
IR)
automatically
detected
so
options
1-8
will
correspond
to
sources
1
signal.
If
using
in
different
parts
of
the
same
room
7 using two identical units within close range of the IR
are
pressing the SYSTEM CODE button on the handset
matrix
by pressing
the left/right
arrow buttons buttons
in each numbered
the
matrix
by
pressing
in each
3
6
on the matrix.
Press
buttons
1-8
toneed
scrollto
through
your
6 you
previous
/ next
buttons
4not
that
will
the Matrix
setting.
he
m the
matrix
display
remotely
side,
from
the the
display
side, the
the left/right arrow
PUT
OUTPUT
3signal. If using in different parts1-8
of the same room it1is likely 4TIMES
rapidly
activates
thechange
alternative
SYSTE
INPUT
SELECT
INPUT
SELECT
2
2
OUTPUT
8
OUTPUT
OUTPUT
OUTPUT
section
on
the
handset.
options
as
you
would
channels
on
a
regular
TV
remote.
NNEL
CHANNEL
numbered
OUTPUT
section
on
the
handset.
HINT
If
your
remote
control
is
not
working,
before
yular
detects
output
which
location
particular
output
location
INPUT
SELECT
INPUT
SELECT
INPUT
SELECT
INPUT
SELECT
that
you
will
not
need
to
change
the
setting.
0x4e,
allowing
independent
control
of
a
second unit.
WhenCHANNEL
using the remote control locally, i.e. pointed directly at the
To
change
handset
battery
HANNEL CHANNEL
4
7
7
4
2
5 theagain
only
on
sources
the1-8
selection
for theofprevious
sources/1-8
changing
the battery,
try5button
changing
System
three
times
to reverts
back
to default
0x
HINT
matrix,
nextforbuttons are used to scroll between the
3 ofallows
3
If your
remote
control
is Code
not
working,
before
11the
here
pull
out
button
tion
- the
rightinput
handsources
button
- connected
the
rightand
hand
1 using
1 Pinch
5HINT
to the matrix for each
individual
output
on
the
handset
in
case
it
has
accidentally
been
battery,
try
changing
the
System
Code
on
the
hand
5
8
8
If your remote control is not working, before changing
the
3
6NOTE Changing
6 been
next
buttons
ctivated.
4
the switched
System
only neces
4 previous
display. So/ for
example,
using the previous /battery,
next buttons
for 1 the System
accidentally
to an is
alternative
ma
switched
an alternative
control
modeCode
try changing
Code on thetohandset
in case it hasmatrix
22Previous2 / next buttons
6
2
are
using
two
identical
units
within
close
range o
6
allows
you
to
select
the
source
to
be
set
to
display
1
manu-ally.
mode.
droom
are in with
the Master
a display
Bedroom
withremote
a display
When
using
the
control
locally,
i.e.
pointed
directly
at
the
has
accidentally
been
switched
to
an
alternative
matrix
control
Install battery ‘+’ side 4
7signal. If using
7 in different parts of the same room
5
5 See below:
OUTPUT
7 to scroll between the
ut
3 of the
zone
ismatrix,
the the
output
zone is/ next buttons are used
Toutput
INPUT
previous
up and only Control
use7CR
3SELECT
3SELECT
33matrix,
HANNEL
When
using
the
remote
control locally,mode.
i.e. pointed directly Remote
at the Display
End
IR) the setting.
Install
battery
‘+’ side
that
you
will
not(Remote
need to change
cted
ill6correspond
so options
toMatrix
1-8
sources
willSystem
correspond
to sources
2025 3V batteries. Slide5
Code
Switch
sources
connected
to the
matrix
for8eachare
individual
output
6 input
up and
only
use
CR
8Remote Control
8
at
the
matrix,
the
previous
/
next
buttons
used
to
at the Display End (Remote IR)
1-8
Press
buttons your
1-8
to scroll through your
41 to scroll
4 2025
compartment
back
into
44 through
8pull
display.
So
for example,
using
the
/ ‘Call
nextBack’
buttons
for 1
3V
Slide
Pinch
here
and
out
The
MX0606/0808-PP
features
anprevious
intuitive
IR
system
scroll
between
thebatteries.
input
sources
connected
to the
matrix
When
controlling
remotely
from
the
display
ular
uld
TV remote.
a regular
TV remote.
Remote
Control
at
the Display
End
(Remote
IR) the matrixHINT
If
your
remote
control
is not working,
7 channels
7 on
the
handset.
When controlling the matrix
remotely
from thebefore
displa
compartment
into
6
you
to select
theback
source
toisbeable
settotodistinguish
display 1where
manu-ally.
of
control
through
which
the
matrix
the
5forallows
52
5
OUTPUTCode OUTPUT
each individual
output
display.
So
for
example,
using
side,
the
matrix
automatically
detects
which
particular
battery,
try
changing
the
System
on theINPUT
hands
matrix
automatically
detects
which
particular
output
SE
5 See
the handset.
When and
controlling
the matrix remotely from the display side, the
below:
CHANNEL
remote
handset
is
being
used
to
change
INPUTS
OUTPUTS
CHANNEL
8
8 previous / next buttons for 1 allows you to select the OUTPUT
has
accidentally
been
switched
toselection
an alternative
ma
OUTPUT
the
output
location
the
user
is
at
and
only
allows
the
selection
the
user
is
at
and
only
allows
the
of
source
matrix
automatically
detects
which
outputSELECT
location
INPUT
INPUT SELECT
The same
switching
functions
can particular
alsoCHANNEL
be accessed
via7the
on thebasic
user’s
location.
6 and is able
63
6 to switch accordingly depending
CHANNEL
mode.
MatrixtoSystem
Switch
that particular
location
using
button
1the
1 - the r
6 source
set Code
to display
1 manually.
ofselection
sources
1-8
that
location
using
the
Install
batteryof‘+’
sidefor1-8
the
user
is at and
only allows the
sources
forparticular
remote
control.
As such, be
the
of the handset
and
operation
differs
asic switching functions
can function
also be accessed
via thebuttons
button
will be
deactivated.
up
and
only
use
CR
4
that
particular
location
using
the
button
the
right
hand
1
7
1
7
7
8
See
below:
button
the
right
hand
button
will
be
deactivated.
depending
on where the handset
being
used. IR ‘Call Back’ system
rol.
The
MX0606/0808-PP
featuresis an
intuitive
Operation
of the handset is the same
regardless
of location
2
2
7
2025
3V batteries.
Slide–
button will be deactivated.
For example,
if you
are
the Master
of
control
through
which
the
matrix
is
able
to
distinguish
where
Remote
Control
at
theinDisplay
EndBedroom
(Remotewith
IR) a
locally
(source/IR
emitter)
or the
remotely
(display/IR
receiver).
In
the
event
that
two
MX0606/0808-PP
units
are
used side
5 handset
f 8the
2 compartment
8 is the same
2 back
8 regardless of location –
OUTPUT
into
connected
to
output
3
of
the
matrix,
the
output
zone
INPUT
SELECT
3
3
For example,
you are in the Master
Bedroom with
a display
System
Switch
For example,
if you
are in the Master Bedroom
remote
handset
isCode
being
used
change
INPUTS
andifOUTPUTS
by
in the(display/IR
rack,
the matrix
is to
capable
of switching
between
CHANNEL with
rce/IR emitter)
or side
remotely
receiver).
the handset.
8 Matrix
When
controlling
the
matrix
remotely
displa
Simply toggle through the
INPUT sources
connected to the
OUTPUT
automatically
detected
so options
1-8from
will the
correspon
connected
to
output
3 of the3matrix,
the output
zone is
INPUT
SELECT
twoisdistinct
Systemaccordingly
Codes to allow
control
ofon
either
matrix
OUTPUT
6
OUTPUT
and
able toIRswitch
depending
the
user’s
location.
3
a
display
connected
to
output
3
of
the
matrix,
the
CHANNEL
matrix
automatically
detects
which
particular
output
INPUT
SEl
matrix
by
pressing
the
left/right
arrow
buttons
in
each
numbered
1-8
on
the
matrix.
Press
buttons
1-8
to
1
4
4 scroll
e through the INPUT
sourcesthe
connected
to the OUTPUT
CHANNEL
CHANNEL
automatically
detected
so options 1-8 will correspond to sources
OUTPUT
hand-set.
Asindividually
such, thevia
function
of
the
handsetan
buttons
and
operation
differs
INPUT
SELECT
INPUT
SELECT
The
MX0606/0808-PP
features
intuitive
IR
‘Call
Back’
output
zone
is
automatically
detected
so
options
1-8
the
user
is
at
and
only
allows
the
selection
of
source
OUTPUT
section
on
the
handset.
options
as
you
would
channels
on
a
regular
TV
remo
CHANNEL
CHANNEL
essing
the
left/right
arrow
buttons
in
each
numbered
The same
basic
also 1-8
be4 accessed
via the your
1-8 on
the switching
matrix. Press
buttons
to scroll through
1functions4 can
7
depending on where the handset is being
used. is able to
button
1the
15 - the r
2 using
CT
5
INPUT
the matrix
to sources that
1-8particular
on the location
matrix.
Press
ction SELECT
on thesystem
handset.of control through which remote
control.
options
as you would channels will
on a correspond
regular TV remote.
1
1
button
will
be
deactivated.
distinguish
the
remote handset units
is being
usedside
to
2
8
5 buttons51-8 to scroll through your options as you would
In the eventwhere
that two
MX0606/0808-PP
are
Operation
the used
handset
26
26
3
previous /ofnext
buttonsis the same regardless of location –
For example, if you are in the Master Bedroom with a
change
and
and
is
able
to
switch
channels
onreceiver).
a regular TV remote.
by side INPUTS
in the rack,
theOUTPUTS
matrix
is
capable
of
switching
between
2
2 locally (source/IR emitter) or remotely
(display/IR
OUTPUT
3
6 i.e. pointed
6 directly at the
next buttons
When
using
remote
control
locally,
connected to output
the output
SELECTzone
37
accordingly
on the
user’s
location.
43 of the37matrix,INPUT
two distinct depending
IR System Codes
to allow
control
ofthe
either
matrix
CHANNEL
Simply
toggle
through
the
INPUT
sources
connected
to
the
matrix,
the
previous
/
next
buttons
are
used
to
scroll
between
the
automatically
detected
so options 1-8 will correspon
3 Support:
3 support@wyrestorm.com US: +866 677 0053 EU: +44 (0) 1793 230 343
the remote control
locally, via
i.e. pointed
directly
at the
Technical
10
individually
the hand-set.
4
7 buttons 7in each numbered
matrix by pressing the left/right
arrow
1-8 on the matrix. Press
15
48 buttons 1-8
48 to scroll
revious / next buttons are used to scroll
between
the input sources connected to the matrix for each individual output
OUTPUT
OUTPUT
INPUT SELECT
INPUT SELECT
OUTPUT
section
on
the
handset.
4
4
display. So for example, using the previous / next buttons for 1
options
as
you
would
channels
on
a
regular
TV remo
CHANNELoutput
CHANNEL
es connected to the matrix for each individual
5
8
8
26
5
5
or example, using the previous / next buttons for 1 allows you to select the source to be set to display 1 manu-ally.
15
15
6
o select the source to be set to display 1 manu-ally. See below:
37
6
6
previous / next buttons
Matrix
System
Code
Switch
2
2
6
6
Technical Support: support@wyrestorm.com
US:
+866
677
0053
EU:
+44
(0)
1793
230
343
9
7
When using the remote control
locally, i.e. pointed directly at the
48
7
7
tem Code Switch
Thesupport@wyrestorm.com
MX0606/0808-PP
an
IRscroll
‘Call
Back’ EU:
system
the previous / nextfeatures
buttons
areintuitive
used to
between
the
Technical
Support:
US:
+866
677
0053
+44 (0) 1793 230 343
37
37 matrix,
10
8thethe
of control
through
which to
matrix
is able
to distinguish
6/0808-PP features an intuitive IR ‘Call Back’ systeminput
sources
connected
matrix
for each
individual where
output the
5
8
8
remote handset is being used to change INPUTS and OUTPUTS
OL
so when an OUTPUT selects a certain INPUT, the CALL-BACK
IR signal of that RJ45 port selects the relevant IR TX port to
OUTPUT the control signal.
Display
Reciever
IR Path
IR Receiver
3
1
2
3
4
2
4
3
4
4
1
2
3
HDBT OUT 1
HDBT OUT 2
HDBT OUT 3
HDBT OUT 4
4
HDBT OUT 5
HDBT OUT 6
HDBT OUT 7
HDBT OUT 8
signal to be combined and communicated for that input to be
controlled remotely.
IR Path
Single Cat5e/6/7
70m/230ft
Display
Reciever
1
2
3
1
2
3
1
2
3
1
2
3
4
2
4
3
IR Path
IR Receiver
1
signal
of that RJ45 OUTPUT links INPUT 3 with IR TX3 for the
HDMI
Cable
4
UTP
Out Input
1
HDMI
1
UTP
IR Out
TX 12
Cat5e/6/7 up to
UTP
Out Input
3
HDMI
2
70m (230ft)
UTP
IR Out
TX 24
UTP
Out Input
5
HDMI
3
IR Out
TX 36
UTP
HDMI Source
HDMI
4
UTP
Out Input
7
IR Out
TX 48
UTP
HDMI Input 5
IR RX Receiver
IR TX 1
2 02
HDMI Input 6
IR TX 2
HDMI Input 7
IR TX 3
HDMI Input 8
IR TX 4
4
1
1
2
3
1
2
3
1
2
3
1
2
3
4
2
4
3
4
4
4
IR TX Emitter
IR TX Receiver
1
1
2
3
1
2
3
1
2
3
1
2
3
4
2
4
3
4
IR RX Receiver
IR Path
3
2
IR Path
2
1
IRenable
TX 4 the IR signal to travel both ways via the single Cat5e/6/7
HDMI
cable.Input 5
IR TX 1
The sequence
of IR TX numbers correspond to the HDMI INPUTS
HDMI
Input 6
IRso
TXwhen
2
an OUTPUT selects a certain INPUT,
the CALL-BACK
IR TX Receiver
HDMI
Input of
7 that RJ45 port selects the relevant IR TX port to
IR signal
IR TX 3
OUTPUT the control signal.
101
HDMI Input 8
IRExample:
TX 4
If OUTPUT 1 selects INPUT 3, the CALL-BACK IR
IR Path
1
1
A key feature on our HDBaseT Lite Matrix range is discrete IR
HDMI
Input
control
of1the matrix, sources and displays from any location – so
IR TX 1
inputs at the matrix end can be controlled at a display location and
HDMI Input 2
can be controlled at the matrix location.
IRdisplays
TX 2
HDMI Input 3
This is accomplished by placing a series of IR Emitters on devices
IR TX 3
to control
atSource
all locations you wish to control from to
HDMI
HDMI
Input 4and Receivers
IR Path
IR Path
a switcher
and extender of multiple HDMI signals to multiple HDMI
The Wyrestorm MX0606/0808-PP is not only a switcher and
receivers located remotely, it also passes IR control
extender of multiple HDMI signals to multiple HDMI receivers
Single Cat5e/6/7
signals
through the IR call-back
system to the matrix
located remotely, it also passes
IR control signals through the
70m/230ft
and IR
HDMI
sources
for
full,
independent
control
of all
call-back system to the matrix and HDMI
sources
for full,
connected
inputs
fromof output
locations.
independent
control
all connected
inputs from output locations.
Example: If OUTPUT 1 selects INPUT 3, the CALL-BACK
Example: If OUTPUT 1 selects INPUT 3, the CALL-BACK IR
IRsignal
signal
of that
RJ45
OUTPUT
links INPUT
withforIRthe
TX3
of that
RJ45
OUTPUT
links INPUT
3 with IR3TX3
for
the
signal
to
be
combined
and
communicated
for
that
Two-way
IR Call-back
Between Matrix,
Sources
signal
to be combined
and communicated
for that
input toand
be
input
to beremotely.
controlled
remotely.
Displays
from Multiple
Locations
controlled
IR Path
HDBT OUT 2 HDBT OUT 6
HDBT OUT 3 HDBT OUT 7
The IR
Wyrestorm
MX0606/0808-PP
is not only
Call-back
of Matrix
Source
HDBT
OUT 4 and
HDBT
OUT 8 Devices
IR Path
OUT 1 and
HDBT
OUT 5 Devices
IR Call-backHDBT
of Matrix
Source
4
4
01
4
HDMI Cable
At Matrix
Matrix end:
Insert
the 3.5mm
jacks ofjacks
the IRofTX
Emitters
101 At
end:
Insert
the 3.5mm
the
IR TX
UTP Out 1
IR RX Receiver
included with the unit into the IR TX Emitter ports at the
Emitters
included
with the unit into the IR TX Emitter ports
UTPrear
Out
2 the matrix
of
according to input. The IR signal is added
at the
according
to input. The IR signal
Cat5e/6/7
up to
UTPrear
Out 3of the matrix
to the HDMI of70m
the (230ft)
input device so, for example, if the user
UTP Outto4 the HDMI of the input device so, for example,
is added
is watching Blu-ray on input 3, the IR signal will be directed
UTP
Out is
5 watching Blu-ray on input 3, the IR signal
if the
user
UTPthrough
Out 6 the IR TX3 socket to control the device. As each
will be directed through the IR TX3 socket to control the
UTP Out 7
device.
UTP Out 8
A key feature on our HDBaseT Lite Matrix range is
discrete IR control of the matrix, sources and displays
from any location – so inputs at the matrix end can be
controlled at a display location and displays can be
controlled at the matrix location.
IR RX Receiver
Technical Support: support@wyrestorm.com US: +866 677 0053 EU: +44 (0) 1793 230 343IR TX Emitter
11
IR Path
Two-way IR Call-back Between Matrix, Sources and
Displays from Multiple Locations
1
1
2
3
1
2
3
1
2
3
1
2
3
4
2
4
3
4
4
10
1
1
2
3
1
2
3
1
2
3
1
2
3
4
2
4
3
4
4
01
4
At Matrix end: Insert the 3.5mm jacks of the IR TX Emitters
included with the unit into the IR TX Emitter ports at the
rear of the matrix according to input. The IR signal is added
to the HDMI of the input device so, for example, if the user
is watching Blu-ray on input 3, the IR signal will be directed
through the IR TX3 socket to control the device. As each
11
IR Path
02
This is accomplished by placing a series of IR Emitters on
devices to control and Receivers at all locations you wish
to control from to enable the IR signal to travel both ways
via the single Cat5e/6/7 cable.
The sequence of IR TX numbers correspond to the HDMI
INPUTS so when an OUTPUT selects a certain INPUT,
the CALL-BACK IR signal of that RJ45 port selects the
relevant IR TX port to OUTPUT the control signal.
4
EU: +44 (0) 1793 230 343
-RX2)
with
signal
to
HDMI
and carried
As with
thethe
IR IR
TX,
thethe
IRconverted
RX
are
allocated
to their
Output2-RX2)
with
IRports
signal
converted
to HDMI
Insert
3.5mm
jacks of ports
IRcable.
RX (Output1-RX1,
receivers into RX
ports,
along
the single
Cat5e/6/7
respective
UTP
OUTPUT
Output2
and carried
along
single
Cat5e/6/7
cable.
making sure
the the
receivers
themselves
are placed
in
-RX2) with the IR signal converted to HDMI and carried
Insert
3.5mm
jacks
of
IR
RX
receivers
into
ports,
clear
view
at
the
to
receive
an
infrared
signal
fromRX
the
As with
thejacks
IRCat5e/6/7
TX,
IRreceivers
RX portsinto
areRX
allocated
to
their
Insert
3.5mm
of the
IR RX
ports,
along
the single
cable.
remote
handset
used
control
the
display
outputs.
making
sure
the
receivers
themselves
are
placed
making
sure the
receivers
themselves
are placed in Output2
respective
UTP
OUTPUT
ports (Output1-RX1,
in clear
clear
view
at
the
to
receive
ansignal
infrared
signal
view
at the
to
receive
an
infrared
from
the
-RX2)
with
the
IR
converted
to
HDMI
and
carried
Insert
3.5mm
jacks
ofsignal
IR RX
receivers
into
RX
ports,
NOTE
The
Call-back
function
can
be
turned
on/off
remote
handset
used
control
the
display
outputs.
from
the sure
remote
handset
used
control
theindisplay
along
the single
Cat5e/6/7
cable.
making
the receivers
themselves
are placed
by accessing the Wyrestorm COMCTL software. See
clear view at the to receive an infrared signal from the
outputs.
ADVANCED
OPERATION
NOTE
Call-back
can
be turned
on/off
remote
handset
usedfunction
control
the
display
outputs.
InsertThe
3.5mm
jacks
of IR RX
receivers
into
RX ports,
by accessing
the
Wyrestorm
COMCTL
software.
See
02
At
display
end:
Insert
the
IR
RX
Receiver
jack
into the IR
making
sure
the receivers
themselves
are
placed
in
NOTE
The
Call-back
function
can
be
turned
on/off
ADVANCED
OPERATION
NOTE
RX
port
of
the
display
receiver
balun,
with
the
receivers
The
Call-back
function
can
be
turned
on/off
clear
view
at
the
to
receive
an
infrared
signal
from
the See
by accessing
the
Wyrestorm
COMCTL
software.
themselves
placed
in clear
view
on
ordisplay
near
displays
byremote
accessing
the
Wyrestorm
COMCTL
software.
See
02 At
display
end:
Insert
the
IRcontrol
RX
Receiver
jackthe
intooutputs.
the
IR to
handset
used
the
ADVANCED
receive
anOPERATION
infraredreceiver
signal from
thewith
remote
handset used to
ADVANCED
OPERATION
RX
port
of the
display
balun,
the receivers
control
inputs.
themselves
placed
in
clear
view
on
or
near
the
displays
to
NOTE
function
can be
turned
on/off
022 At display The
end:Call-back
Insert the IR
RX Receiver
jack
into the
IR
At display
end:
Insert
theremote
IR RXhandset
Receiver
jack into
receive
an
infrared
signal
from
the
used
byport
accessing
the Wyrestorm
COMCTL
RX
of the display
receiver balun,
with the software.
receiversto See
Insert
the IRofTX
Emitter
jack receiver
into the IRbalun,
TX portwith
of thethe
thecontrol
IR
RXinputs.
port
the
display
themselves
placed
in clear
view on
or near the displays
to
ADVANCED
OPERATION
display receiver
balun, ensuring that the emitter sensor is
receivers
themselves
placed
inremote
clear handset
view onused
or near
the
receive an
infrared signal
from the
to
securely
attached
to
infrared
sensor
window
of
the
display.
Insert
the
IRreceive
TX
Emitter
IR
TX from
port of
theinto
02
At display
end:
Insert
theinto
IR the
RX
Receiver
jack
the IR
displays
to
an jack
infrared
signal
the
remote
control
inputs.
display
receiver
balun,
ensuring
that the
emitter
is
RX port
of the
display
receiver
balun,
withsensor
the receivers
handset
used
control
inputs.
Follow
the to
same
connection
andwindow
positioning
fordisplay.
all baluns/
securely
attached
to infrared
sensor
of the
themselves
placed
in
clear
view
on
or
near
the
displays
to
Insert
the IRconnected
TX Emitter
into the IR TX port of the
displays
tojack
the matrix.
receive
an
infrared
signal
from
the
remote
handset
used
to
display receiver balun, ensuring that the emitter sensor is
Insert
the
TX connection
Emitter jack
into the IR
port of the
Follow
theIR
same
and positioning
for TX
all baluns/
control
inputs.
securely
attached
to
infrared
sensor
window
of
the
display.
If all
IR TX Emitters
IR RX Receivers
positioned
displays
connected
to theand
matrix.
display
receiver
balun,
ensuring
that the are
emitter
sensor
IR TX port is allocated to an individual HDMI input port, if
and connected correctly with sources, displays and display
is
securely
attached
to
infrared
sensor
window
of
the
Follow
connection
and
positioning
for
baluns/
Insertthe
thesame
IRfully
TX
Emitterand
jackthe
into
the IR
TX
of the
the user is unable to establish IR control of the device, care
powered
matrix
set
toallport
IR
call-back
If all receivers
IR TX Emitters
and IR RX Receivers
are
positioned
As each IR should
TX port taken
is allocated
to an
individual
HDMI
display.
displays
connected
to
matrix.
display
receiver
ensuring
the emitter
sensor
totocheck
that,
firstly,
the input
IR emitter
enabled
and
IRbalun,
TXthe
Swicth
modethat
activated,
two-way
IR willis
IR TX port isbeallocated
an individual
HDMI
port, ifand
and connected
correctly
with sources,
displays and
display
input port,
if
the
user
is
unable
to
establish
IR
control
of
HDMI
input
ports
match
(Input
1-TX1,
Input2-TX2
etc.)
with
securely
attached
to
infrared
sensor
window
of
the
display.
now
be
possible.
receivers fully powered and the matrix set to IR call-back
If all IR
TXsame
Emitters
and IR RX Receivers
are positioned
plugs
secured
correct
that
the IR TX
the device,
care
should
be
taken
toand
check
that,
firstly,
Follow
the
connection
and
positioning
for
should
be taken
to in
check
that,ports,
firstly,
thesecondly,
IR emitter
and
andControl
IR TX Swicth mode activated, two-way IR willall baluns/
IRenabled
Extender
IR TXemitter
port issensors
allocated
tofirmly
an individual
HDMI
input
port, if of
and
connected
correctly
displays and
are
attached
directly
to the
Follow
the
same
connection
and positioning
fordisplay
all baluns/
HDMI input
match
(Inputports
1-TX1,match
Input2-TX2
etc.)front
with
the IR emitter
andports
HDMI
input
(Input
1-TX1,
displays
connected
to with
the sources,
matrix.
now be possible.
the user
is unable
to establish
IR sensor
controlwindows
of the device,
care
receivers
fully
powered
and
the
matrix
set
to
IR
call-back
inputs
and
covering
infrared
of
the
source
plugs
secured
in
correct
ports,
and
secondly,
that
the
IR
TX
displays
connected
to
the
matrix.
Input 2-TX2
etc.)
withto plugs
secured
in correct
should
be taken
check that,
firstly, the
IR emitterports,
and
IR Extender
Control
enabled
and IR TX Swicth mode activated, two-way IR will
devices.
emitter
sensors are firmly attached directly to the front of
and secondly,
that
thematch
IR TX
emitter
areetc.)
firmly
If allnow
IR be
TXpossible.
Emitters and IR RX Receivers are positioned
HDMI input
ports
(Input
1-TX1,sensors
Input2-TX2
with
inputs and covering infrared sensor windows of the source
If all IR TX Emitters
andwith
IR RX
Receivers
are positioned
attached
directly
to
the
front
of
inputs
and
covering
and
connected
correctly
sources,
displays
and
plugs
secured
in
correct
ports,
and
secondly,
that
the
IR
TX
Some
later adjustment
may be needed
the location
devices.
IR TX
port
is allocated
to an individual
HDMItoinput
port, if of the IR Extender
Control correctly with sources, displays and display
and
connected
sensors
are firmly
attached
directly
toresults
the front
of
infraredemitter
sensor
windows
of
devices.
display receivers fully powered and the matrix set to IR
sensor
to achieve
thethe
bestsource
performance
- sometimes
receivers fully powered and the matrix set to IR call-back
inputs
and
covering
infrared
sensor
windows
of
the
source
moving
the sensor
to different
areas
on
the
source
call-back enabled and IR TX Switch mode activated, twoSome
later
adjustment
may
be
needed
toIR
the
location
ofcan
the
should
be
taken
to
check
that,
firstly,
the
emitter
and
enabled and IR TX Swicth mode activated, two-way IR will
devices.
improve
IR performance.
sensor
to achieve
the best performance results - sometimes
SomeHDMI
laterinput
adjustment
may
be 1-TX1,
needed
to the location
ports match
(Input
Input2-TX2
etc.) with
moving the
sensor to different
areas
on the sourceresults
can
of theplugs
sensor
to
achieve
the
best
performance
secured
in
correct
ports,
and
secondly,
that
the
NOTE
Some
later
adjustment
may
be
needed
to
the
location
ofbeTX
the
Infrared receiving areas of devices canIR
improve IR performance.
sometimes
moving
the
sensor
to
different
areas
on
the
emitter
sensors
areshining
firmly
attached
directly
to the
front
of
sensor
to achieve
the
best
results
- sometimes
located
by
a performance
flashlight
onto
the
front
of the
source
can
improve
IR
performance.
inputs
and
covering
infrared
sensor
windows
of
the
source
moving
the
sensor
to
different
areas
on
the
source
can
device
–
the
sensor
should
be
able
to
be
seen
through
NOTE
Infrared receiving areas of devices can be
devices.
improve
the IR
plastic
as aasmall,
round
object
inside.
located
byperformance.
shining
flashlight
onto
the front
of the
NOTE Infrared
receiving
areas
of devices
be
device – the
sensor should
be able
to be seencan
through
NOTE
Infrared
areas
of devices
can beof
Some
adjustment
may
be
needed
tothe
the location
of the
the
plastic
as a small,
round
object
inside.
located
bylater
shining
areceiving
flashlight
onto
front
located
by shining
flashlight
onto the
front-of
the
sensor
to– achieve
the abest
performance
results
sometimes
the device
the sensor
should
be able
to be
seen
device
–
the
sensor
should
be
able
to
be
seen
through
moving the sensor to different areas on the source can
through
the
plastic
as
a
small,
round
object
inside.
the plastic as a small, round object inside.
improve IR performance.
NOTE Infrared receiving areas of devices can be
located by shining a flashlight onto the front of the
device – the sensor should be able to be seen through
the plastic as a small, round object inside.
As with the IR TX, the IR RX ports are allocated to their
respective UTP OUTPUT ports (Output1-RX1, Output2
-RX2)
the
IRthe
signal
converted
to HDMI
and
carried to
AsAs
with
the
IRTX,
TX,
IRports
RX are
ports
are allocated
with
thewith
IR
the
IR RX
allocated
to
their
along
the
single
Cat5e/6/7
cable.
respective
UTP OUTPUT
ports (Output1-RX1,
Output2
their
respective
UTP OUTPUT
ports (Output1-RX1,
way now
IR will
now be possible.
be possible.
IR Should
Extender
localControl
control of the
Matrix via the front panel
IR sensor
be an of
issue,
Should
local control
the for
example
if
the
sensor
Matrix via the front panel is
obstructed
the unit
IR sensor
be anor
issue,
for is
Should
local
control
ofis the
installed
a closed
area out
example
if thein
sensor
Matrix
via the
front
panel
of infrared
lineunit
of
sight, the
obstructed
or the
is
IR RX
Receiver
included
IR sensor
an issue,
forout with
installed
in be
a closed
area
the
matrix
can
be
inserted
into
example
if
the
sensor
is
of infrared line of sight, the
the
IR
EXT
port
at
the
rear
obstructed
or
the
unit
is
IR RX Receiver included with to
extend
the
IR inserted
sensor
installed
incan
a closed
area range
out and enable local control of the system.
the
matrix
Should
localbe
control of into
the
of infrared
line of
theto
the
IR EXT port
at sight,
the rear
Matrix
via
the
front
panel
NOTE
orwith
poorly
secured
Emitters
Receivers
IR RX
Receiver
included
extend
the IRMisplaced
sensor
range
and enable
localIR
control
of theand
system.
IRmatrix
sensor
be in
aninserted
issue, for
result
intermittent
the may
can be
into IR control signals passed to and from
example
ifport
theCheck
is toplacement and adjust if necessary.
the
matrix.
your
NOTE
the
IR EXT
atsensor
the
rear
Misplaced
or poorly
secured IR Emitters and Receivers
obstructed
or
the
unit
isIR
extend
the IR
sensor range
and
enablesignals
local control
of to
theand
system.
may
result
in intermittent
control
passed
from
installed
a closed
out
the
matrix. in
Check
yourarea
placement
and adjust if necessary.
NOTE
of infrared
line of or
sight,
the secured IR Emitters and Receivers
Misplaced
poorly
IR RX
Receiver
included IR
with
may
result
in intermittent
control signals passed to and from
thematrix.
matrixCheck
can beyour
inserted
into and adjust if necessary.
the
placement
the IR EXT port at the rear to
NOTEthe
Misplaced
or poorly
secured
IR Emitters
extend
IR sensor range
and enable
local control
of the system.
Technical Support: support@wyrestorm.com US: and
+866Receivers
677 0053 EU:
+44result
(0) 1793
343
12
may
in 230
intermittent
IR control
NOTE Misplaced
secured
Emitters
and Receivers
signals
passed or
to poorly
and from
theIR
matrix.
Check
your
Technical Support: support@wyrestorm.com US: +866
677result
0053 in EU:
+44
(0) 1793
230 343
12and from
may
intermittent
IR
signals passed to
placement
and
adjust
if control
necessary.
the matrix. Check your placement and adjust if necessary.
EU: +44 (0) 1793 230 343
12
11
ADVANCED REMOTE CONTROL
ADVANCEDADVANCED
REMOTE CONTROL
REMOTE CONTROL
11.
Advanced Remote
Control
11. Advanced Remote
Control
IR Call Back and Third Party Control systems
Please note: Due to the differing method of control
based on location, if you are using a third party
IR Call Back
andlearning
Third Party
control
system,
theControl
control systems
from the IR is NOT
recommended
will method
be limited
to scrolling
Please note: Dueas
to control
the differing
of control
based onup/
location,between
if you are inputs.
using a third
party control
system,
learning the
down
For discrete
source
selection
control
theto
IR import
is NOT recommended
controlfor
willcontrol
be limited
you
willfrom
need
discrete hexas
codes
to
scrolling
up/down
between
inputs.
For
discrete
source
selection
systems. These can be obtained through the Wyrestorm
IR
Call
Back
and
Third
Party
Control
systems
you
will
need
to
import
discrete
hex
codes
for
control
systems.
website, by contacting our technical support or you can
These can be obtained through the Wyrestorm website, by
input
them
manually.
Please
note:
Due to the differing method of control based on
11. Advanced Remote
Control
12.
Advanced Operation
Controlling the MX0606/0808-PP using RS232 and
COMCTL PC Software
12. Advanced Operation
Typically, unless alternative methods of controlling
Controlling
using
RS232
and
the matrix the
are MX0606/0808-PP
chosen or problems
with
device
COMCTL
PC
Software
communication through the matrix encountered,
12. Advanced Operation
basic operation
is all that
is required
to operate
your
Typically,
unless alternative
methods
of controlling
the matrix
are
chosen
or problems withHowever,
device communication
through
the matrixon
MX0606/0808-PP.
the following
information
encountered,
operation
all thathow
is required
to operate
advanced basic
operation
willisdetail
the matrix
system can
Controlling
theand
MX0606/0808-PP
using RS232
and
your
MX0606/0808-PP.
the following
information
be
configured
forHowever,
advanced
control
and settings
can
COMCTL
PC
Software
onbe
advanced
operation
will
detail
how
the
matrix
system
can
be
altered or data manually input should such problems
configured and for advanced control and settings can be altered
Typically,
alternative
methods
controlling
matrix
are
arise,
asunless
well as
configuring
theofsystem
for the
third
party
or data manually input should such problems arise, as well as
chosen or problems with device communication through the matrix
control.
configuring the system for third party control.
contacting our technical support or you can input them manually.
encountered, basic operation is all that is required to operate
location, if you are using a third party control system, learning the
your MX0606/0808-PP.
However, the following information
RS232
Remote
Control
control
from
the
IR
is
NOT
recommended
as
control
will
be
limited
For
reference:
The
IR
is
NEC
and
possesses
a
carrier
wave
of
For reference: The IR is NEC and possesses a carrier
RS232
Remote
Control
on advanced operation will detail how the matrix system can be
to
scrolling
up/down
between
inputs.
For
discrete
source
selection
38KHz
with
a
system
code
of
0x00
wave of 38KHz with a system code of 0x00
Control of the matrix is possible through RS232 using third party
configured and for advanced control and settings can be altered
you will need to import discrete hex codes for control systems.
control
systems
or matrix
the dedicated
Wyrestorm
COMRS232
CTL software
Control
of the
is possible
through
using
or data manually input should such problems arise, as well as
OUTPUT
These can be obtained through the Wyrestorm website, by
included
with your
purchase
(also or
downloadable
from www.
INPUT SELECT
third
party
control
systems
the
dedicated
Wyrestorm
CHANNEL
configuring the system for third party control.
contacting our technical support or you can input them manually.
wyrestorm.com).
COM CTL software included with your purchase (also
RS232 Remotefrom
Control
For
The IR0x0d
is NEC and possesses a carrier wave of
downloadable
www.wyrestorm.com).
0x1d
1 reference:
RS232
Setting
38KHz with a system code of 0x00
Control of the matrix is possible through RS232 using third party
Should third party control be required, please see below for control
control systems
or the dedicated Wyrestorm COM CTL software
RS232
Setting
2OUTPUT 0x1b 0x15
system configuration and hex code input. The RS232 connection
included with your purchase (also downloadable from www.
INPUT SELECT
CHANNEL
on the matrix is female QB9 Users can use a USB to RS232
wyrestorm.com).
Should
third party
be required,
0x12 0x08
3
cable
or a direct
male tocontrol
female serial
cable. please see below
0x1d 0x0d
for
control
system configuration and hex code input. The
1
RS232
Setting
4
5
6
7
8
2
0x55 0x4a
0x1b 0x15
3
0x06 0x03
0x12 0x08
4
0x07 0x02
0x55 0x4a
5
0x44 0x51
0x06 0x03
6
0x1e 0x1a
0x07 0x02
Output1 source select key code:
0x44 0x51
7
0x80 0x81 0x82 0x83 0x84 0x85 0x86 0x87
Output2 source0x1e
select key
code:
0x1a
8
0x90 0x91 0x92 0x93 0x94 0x95 0x96 0x97
Output1
source
select
code:
0xa0
0xa1 0xa2
0xa3
0xa4key
0xa5
0xa6 0xa7
0x80
0x81
0x82
0x83
0x84
0x85
Output4 source select key code: 0x86 0x87
Output2
source
select
key
code:
0xb0
0xb1 0xb2
0xb3
0xb4
0xb5
0xb6 0xb7
0x90
0x91
0x92
0x93
0x94
0x95
Output5 source select key code: 0x96 0x97
Output3
source
select
code:
0xc0
0xc1 0xc2
0xc3
0xc4key
0xc5
0xc6 0xc7
0xa0
0xa1
0xa2
0xa3
0xa4
0xa5
Output6 source select key code: 0xa6 0xa7
Output4
source
select
key
code:
0xd0
0xd1 0xd2
0xd3
0xd4
0xd5
0xd6 0xd7
0xb0
0xb1
0xb2
0xb3
0xb4
0xb5
Output7 source select key code: 0xb6 0xb7
Output5
source
select
key
code:
0xe0
0xe1 0xe2
0xe3
0xe4
0xe5
0xe6 0xe7
0xc0
0xc1
0xc2
0xc3
0xc4
0xc5
Output8 source select key code: 0xc6 0xc7
Output6
source
key code:
0xf0
0xf1 0xf2
0xf3select
0xf4 0xf5
0xf6 0xf7
0xd0 0xd1 0xd2 0xd3 0xd4 0xd5 0xd6 0xd7
0xe0 0xe1 0xe2 0xe3 0xe4 0xe5 0xe6 0xe7
12
Receiveisserial
data from
RS232
on RXD
the matrix
female
DB9.PCUsers
5 4 connection
3 2 1
Should third party control be required, please see below for control
TXD
Transmit
serial
data
to
PC
can
useconfiguration
USB-RS232
cable (supplied) for connection
to
RXD
TXD
system
and hex code input. The RS232 connection
Ground
aonPC
or
a
straight
through
male-male
(not
supplied)
for
Com
Port
Setting
the matrix is female QB9 Users can use a USB to RS232
7 to 6amale
connection
control
interface.
cable9 or 8a direct
to female
serial cable.
Female connector - 9 holes
1
5
4
2
3
3
4
2
5
1
RXD TXD
TXD RXD
Ground
Ground
6
9
7
8
8
7
9
1
2
3
TXD RXD
4
9600bps
Data
8bitsdata from PC
RXD bits
Receive serial
TXD
Transmit
serial
data to PC
Parity
None
Com bits
Port Setting
Stop
1
6
Female
connector
- 9 holes
Male
connector
- 9 holes
COM CTL
Baud rate
5
Baud
rate
Flow
control
9600bps
None
Data bits
8bits
Parity
None
Ground
After fully connecting
all inputs and
outputs
Stop
bits to the
1 matrix and
installing 6the7software,
on
opening
the
program
the
control
8 9
Flowthe
control
Noneas messages
window will display information from
matrix, such
Male connector - 9 Pins
holes
received from the switch such as input/output details, firmware
COMand
CTLcontrol commands/HEX codes that allow the system
version
to be controlled remotely, as well as buttons used to navigate the
After fully
connecting all inputs and outputs to the matrix and
COM
CTL
screen.
installing the software, on opening the program the control
window
willconnecting
display information
from and
the matrix,
suchtoasthe
messages
After
fully
all inputs
outputs
matrix
received from the switch such as input/output details, firmware
and installing the software, on opening the program
version and control commands/HEX codes that allow the system
the control window will display information from the
to be controlled remotely, as well as buttons used to navigate the
matrix,
screen. such as messages received from the switch such
as input/output details, firmware version and control
commands/ASCII codes that allow the system to be
controlled remotely, as well as buttons used to navigate
the screen.
0xf0 0xf1 0xf2 0xf3 0xf4 0xf5 0xf6 0xf7
15
01
16
MX-0606-PP
9
17
MX0606-PP
MX0606-PP
03
04 04
06 06 07
02
03
02
1
05
05
3
2
MX-0808-PP
10 11
10 10
11 11
10 10
11 11
10 1112
12
07 08 08
4
Receive
Message
WindowWindow
01 Receive
Message
5
01
02 Matrix
02 Status
Matrix Status
10 11 10 11 10 11
12
03 Message
03 Message
6 Clear Clear
7
8
06 Com
State -State
Shows
if the matrix
connected
06 Connect
Com Connect
- Shows
if the is
matrix
is connected
04 1Send
Message
Window
04
Send Message
or disconnected
to
the
Com
Port
and
communication
is
Receive
MessageWindow
Window
or disconnected to the Com Port and communication
is
05 2Send
Message
Button
enabled.
Selection
between
ports
is
available
by
pressing
the
05
SendStatus
Message Button
enabled. Selection between ports is available by pressing
the
Matrix
Com Port
Select
button. button.
Com
Port
Select
Message
Clear
3
06 Com
Connect
State State
06 Port
Com
Port Connect
6 Com Connect State - Shows if the matrix is
4 Send Message Window
07 When
the onlythe
option
be to
and and
07 connected,
When connected,
only will
option
willDisconnect
be to Disconnect
07 Com
Select
07 Port
Com
Port Select
connected
or
disconnected
to
the
Com
Port
and
5 Send Message Button
vice versa.
vice versa.
08 6Connect/Disconnect
from
Matrix
08
Connect/Disconnect
from Matrix
communication
istoenabled.
Selection
between
ports
Press Press
connect/disconnect
the matrix
from
Com
Port Connect State
08 to08
connect/disconnect
the
matrixthe
from
theis
software
control.
available
by
pressing
the
Com
Port
Select
button.
software control.
Com
PortSwitch
Select
09 7Input/Output
area area
09
Input/Output
Switch
Connect/Disconnect
from
Matrix
8
10 Select
Presaved
OutputOutput
State 1,State
2, or1,3 2, or 3
10 Select
Presaved
to ENABLE
matrix
communication
7 Connected
Connected
to ENABLE
matrix
communication
When
connected,
the
only
option
will be to
9 Input/Output Switch area
11 10Save
Current
OutputOutput
State 1,State
2, 3 1, 2, 3
11
Save
Current
Disconnect
and
vice
versa.
Select Presaved Output State 1, 2, or 3
Disconnected
to DISABLE
matrix communication
to DISABLE
matrix
communication
Press
to connect/disconnect
the matrix
from the
8 Disconnected
12 11Select
all Current
Inputs/Outputs
Save
Output State 1, 2, 3
12
Select
all Inputs/Outputs
software
control.
Com
Select
Connect/Disconnect
08 08 Connect/Disconnect
Select
all Inputs/Outputs
07 07 Com Select
13 12Settings
13
Settings
13 Settings
14 Set
access
k the Com
dropdown
to see all
Comallports
Select Select
14IP Set
IP access
kConnected
theSelect
Com Select
tomatrix
see
Comavailable.
ports available.
todropdown
ENABLE
communication
14 Set IP access
your
chosen
Com
port
number
and
press
the
CONNECT
button.
your chosen Com port number and press the CONNECT button.
15 15IR15
Set
Area
IR
Set
Area
IR Set
Area
You willYou
notice
button
changechange
to show ‘disconnect’
and and
will the
notice
the button
show ‘disconnect’
Disconnected
to DISABLEtomatrix
communication
EDID
Settings
16 16EDID
Settings
16
EDID
Settings
CONNECT
STATE
change
to
green
for
‘connected’
.
Pressing
the
CONNECT STATE change to green for ‘connected’. Pressing
the
IR Matrix
17
button
again
will
disconnect
the
Com
port
and
the
CONNECT
state state
button
again
will
disconnect
the
Com
port
and
the
CONNECT
17 IR17
Matrix
IR Matrix
Com
Select 8 Connect/Disconnect
7willred.
will show
show red.
1
Receive
Message
Window
–
displays
messages
01 Receive
Message
Window
– displays
messages
received
01 Receive
Message
Window
– displays
messages
received NOTE NOTE
The Com
drop box
offers
options
of ComofPorts
TheSelect
Com Select
drop
box offers
options
Com Ports
• •
• •
Click the
Com Select
dropdown to see all Com ports
received
from
such
assettings
input/output
settings
from the
matrix,
suchmatrix,
assuch
input/output
and command
from
thethe
matrix,
as
input/output
settings
and
commandto connect
to – COM
to connect
to –1-10
COM 1-10
and
command
available. Select your chosen Com port number and
selections.
selections.selections.
09 press
Input/Output
SwitchSwitch
- Switches
connected
inputs per
09 the
Input/Output
- Switches
connected
inputs
per
You
view
the
current
condition
of
all
input/output
CONNECT
button.
You
will
notice
the
button
Youcan
canYou
view
the
current
condition
of
all
input/output
ports
can view the current condition of all input/output ports
output. output.
Operation
as
withas
remote
control
handset.
Operation
with remote
control
handset.
by pressing
the 02
button.button.
ports
bybypressing
the 02
button.
change
to show
‘disconnect’
and CONNECT
STATE
pressing
the
2
change to green for ‘connected’. Pressing the button
Pressing
will delete
the
message
3
Pressing
will delete
the previous
message
Pressing
03
will
delete
theprevious
previous
message
03
again will disconnect the Com port and the CONNECT
received
in
the
window.
received
the window.
received
in the in
window.
state will show red.
04 Send
Window
- Input -your
serial
04 Message
Send Message
Window
Input
yourcommands
serial commands
4for the
Send
Message
Window
-Window
InputWindow
your
serial
matrix
in
the Send
Message
- such
as
for
the
matrix
in the
Send Message
- such as
MX0808-PP
MX0808-PP
instructions
for
or to enter
mode
–mode
and click
commands
foroutputs
theformatrix
inorthe
Send
Message
instructions
outputs
toupdate
enter
update
–Window
and click
- the
such05
as
instructions
for
outputs
or
to
enter
update
Send
button
to
deliver
the
message
to
the
Matrix.
the 05 Send button to deliver the message to the Matrix.
mode
–The
andcontrol
click command
theuses
Send
button to deliver the
The control
command
5 ASCII.
uses ASCII.
message
to the Matrix. The control command uses ASCII.
NOTE
NOTE
To see the firmware version currently used in the
To see the firmware version currently used in the
systemsystem
– power
off andoff
repower
while the
matrix
is connected
– power
and repower
while
the matrix
is connected
NOTE
To
see
thefirmware
firmware
version
currently
used
in
to COM
The
firmware
versionversion
and
creation
date will
be
toCTL.
COM
CTL.
The
and creation
date
will be
the
system
–
power
off
and
repower
while
the
matrix
displayed
together
with the
normal
outputoutput
state of
the of
matrix.
displayed
together
with
the normal
state
the matrix.
MX0606-PP
MX0606-PP
NOTE The Com Select drop box offers options of
Com Ports to connect to – COM 1-10
denotesdenotes
each OUTPUT
sectionsection
with with
Ayellow
large number
yellow number
each OUTPUT
9A large
Input/Output Switch - Switches connected inputs
INPUTS
chosenchosen
by either
the left/right
arrow buttons
INPUTS
byclicking
either clicking
the left/right
arrow buttons
per
output.
Operation
as with
remote
to scroll
inputs numerically
or by pressing
thehandset.
input
tothrough
scroll
through
inputs
numerically
orcontrol
by pressing
the input
numbers
below. below.
numbers
The INPUT/OUTPUT
switch switch
allows output
port selection
The INPUT/OUTPUT
allows output
port selection
(display)
and Input
select
buttonsbuttons
for specific
(display)
andport
Input
port (source)
select (source)
for specific
is connected to COM CTL. The firmware version and
creation date
will Technical
beSupport:
displayed
together
with theUS: +866
Technical
0053
EU: +44
1793
343
14
Support:
US: 677
+866
677 0053
EU:(0)+44
(0)230
1793
230 343
MX-0606-PP
MX-0808-PP
normal output state of the matrix.
14
13
ADVANCED OPERATION
ADVANCED OPERATIO
01
ADVANCED OPERATIO
14
13
8
button again to Connect and power-cyle the matrix
(turn off and on).
ADVANCED OPERATION
A large yellow number denotes each OUTPUT section
with INPUTS chosen by either clicking the left/right arrow
buttons to scroll through inputs numerically or by pressing
the input numbers below.
The INPUT/OUTPUT switch allows output port selection
(display) and Input port select (source) buttons for specific
combinations of displays and sources within the matrix.
combinations
displays
and sources
the matrix.You
You
can saveof your
selections
by within
allocating
your choices
can save your selections by allocating your choices to Save
to Save buttons 1-3 11 and recall previously saved
buttons 1-3 11 and recall previously saved output/ input
5 State
4 3 1-3
2 1
output/
input by
configurations
by pressing
configurations
pressing State 1-3
buttons 10
10 buttons.
RXD TXD
Updates are now active and the MX0606/0808-PP
firmware is now updated.
Control Command Format
Control Command Format
Should users wish to write their own command software
Should users wish to write their own command software
for controlling
controlling
matrix
remotely,
see information
for
thethe
matrix
remotely,
see information
on data on data
RXD
Receive
serial
data
from
PC
formatand
and
baud
settings:
format
baud
raterate
settings:
TXD Transmit serial data to PC
COM
PORT
Setting
COMPort
PORT
Setting
Com
Setting
Ground
Firmware Update
To update theUpdate
system firmware, enter the following
Firmware
9 8code7into6
theupdate
Send Message
Window
to include
one
04 ensuring
To
the system
firmware,
enter the
following
Female connector - 9 holes
space
between
each
section
of
the
code.
4
code into the Send Message Window
ensuring to
1 2of the
3 code.
4 5
include one space between each section
Code: 1CP BE 7C 5F
Code:
ICP BE
5FMessage
Press Enter,
then7C
Send
into firmware update mode.
TXD RXD
05
Ground
to put the matrix
7
6
8
9
Press Enter, then Send Message
5 to put the matrix
Male
connector - 9 holes
Pressfirmware
the Disconnect
button and run the firmware.
into
update 08
mode.
When the firmware has finished updating, press the same
13
button again to Connect
and powercyle the matrix
08
8
Press the Disconnect
button and run the firmware.
(turn off and on).
When the firmware has finished updating, press the same
Updates are now active and the MX0606/0808-PP
firmware is now updated.
1
Baud rate
9600bps
Data bits
8bits
Parity
None
Stop bits
1
Flow control
None
13 Setting
themenu
Settings
menu
to make
Setting
– Enter –
theEnter
Settings
area to
makearea
alternations
to
the
matrix,
IR,
EDID
etc.
See
be-low
for
details.
alternations to the matrix, IR, EDID etc. See below for
details.
MX-0606-PP
2
MX0808-PP
3
03
4
01
02
5
MX-0808-PP
05
04
6
MX0606-PP
06
8
7
08
07
1
01
SWITCH – Quick Switch option is an alternative
method of switching between sources that is faster than
in Normal mode, resulting in less delay between input
SWITCH – Quick
Switch
option
is means
an alternative
method has
selection.
Although
faster,
the
of switching
of switching
sources that is with
fastersome
than indisplays.
Normal As
been
foundbetween
to be incompatible
mode, resulting in less delay between input selection.
a result we recommend Normal Switch as the default 04
Although faster, the means of switching has been found to be
setting due to reliability and compatibility with outputs.
incompatible with some displays. As a result we recommend
Normal Switch as the default setting due to reliability and
compatibility with outputs.
02
03
2
IR CALL-BACK – This toggles the IR Call-Back
function on and off. The default setting is ON
the
to attempt
aid transmission
HDMI signal.
3 matrix
HDMI
LONGtoCABLE
MODEof–the
If devices
connected
This setting is locked by default.
using HDMI are reaching the upper end of the HDMI
UTP LONG CABLE
As with
HDMI
Long
Cable
transmission
limit MODE
(15m /–49ft)
and
signal
interference
or
Mode,
signal transmission
quality isLong
ef-fected
by aMode to ON
loss isif experienced,
switching
Cable
Cat5e/6/7 cable run reaching the maximum distance
capacity (70m / 230ft using RX-1UTP-IR-70), switching
Long Cable Mode to ON will instruct the matrix to attempt
Technical
Support:
US:
+866 677
0053 EU:
(0) 1793
230 343
14
to improve
transmission
over+44
the UTP
in an effort
to improve
IR CALL-BACK – This toggles the IR Call-Back function on
signal
quality.
and off. The default setting is ON
This mode should NOT be used as a general means to
HDMI LONG CABLE MODE – If devices connected using
will instruct matrix to attempt to aid transmission of the
HDMI signal.
14
14
2
4
UTP LONG CABLE MODE – As with HDMI Long
Cable Mode, if signal transmission quality is affected by a
Cat5e/6/7 cable run reaching the maximum distance
capacity (70m / 230ft using RX-1UTP-IR-70), switching
Long Cable Mode to ON will instruct the matrix to attempt
to improve transmission over the UTP in an effort to
improve signal quality.
This mode should NOT be used as a general means
to lengthen transmission distance – we recommend
installers be aware of product specifications and use
equipment best suiting the requirements of the project.
5
Lock/Unlock – To gain access to Long Cable Mode
settings, press ‘unlock’ and enter
‘877379’
NOTE This password cannot be changed
6
3
01
01
4 02
02
03
03
Clicking opens a pop-up window in which you can
04
04
choose to let the system automatically
detect your IP
address, with the result displayed in the box below.
Alternatively, if the system cannot detect an IP address,
Clicking
opens
a pop-up
window
in which
you
can
choose
to
selectClicking
‘Use the
following
IPwindow
Address’
andyou
youcan
can
add to
opens
a pop-up
in which
choose
let the system automatically detect your IP address, with the
manually.
let the system automatically detect your IP address, with the
result displayed in the box below. Alternatively, if the system
result displayed in the box below. Alternatively, if the system
cannot detect an IP address, select ‘Use the following IP
cannot detect
an IP address,
select ‘Usetothe
IP
Selection
enables
the IP address
befollowing
obtained
Address’ and you can add manually.
Address’
and
you
can
add
manually.
automatically, with the result appearing in the white box
01 Selection
Selection enables the IP address to be obtained
below.
01
enables the IP address to be obtained
below.
2 Should
below. no address appear or if the system is unable
02detect
Should
no
address
appear
or if the system
unable
to detect
to
anno
IPaddress
address,
select
manually
3 isisto
02
Should
appear
or ifoption
the system
unable
to detect
an
IP
address,
select
option
to
manually
input
the
IP
03
input the
address.
an IPIPaddress,
select option 03 to manually input the IP
address.
address.
404 Click
Click
04 Click
For full information on LAN control, see NETCTL
NOTE7 ThisEDID
password
cannot
be changed
COPY
SETTING
– Copies EDID informationFor full
information
on manual.
LAN control, see NETCTL section of
section
of this
from one
device
to another
to aid transmission this manual.
06 directly
UTP ENFORCE
– used
to encourage
EDID/HDCP
ifcommunication
communication
problems
ariseOUTPUT
between
incompatible
between
INPUT and
devices.
15 IR SET - The MX0606/0808-PP supports third party
Switching
output
settings
to
ON
instructs
the
matrix
to
output
devices. Use the dropdown boxes to select which INPUT/
15 IR
SET - systems
The MX0606/0808-PP
thirdPressing
party
control
and learning supports
handsets.
the IR
a signal regardless
or hotplug
data
–
OUTPUT
devicesoftodevice
copyEDID/HDCP
from and where
to be
copied
control
systems
and
learning
handsets.
Pressing
the
IR
SET
SET button in the COM CTL main screen allows access
such information is circumvented to force communication in
button
in thetoCOM
CTL
main
access
for userscode
to.
for users
enter
new
IRscreen
code allows
or modify
existing
the event of problems between sync devices. Default setting
to enter new IR code or modify existing code and assign it
and assign it to inputs and outputs so control using third
is OFF.
to inputs and outputs so control using third party systems is
8 FACTORY RESET – restores all matrix settings to
party systems is possible.
If difficulties
are encountered receiving a signal from a
possible.
factory
action
cannot
be reversed.
Toinput
inputor or
amend
IR code,
thebelow:
steps below:
particulardefault.
source toThis
a display,
change
UTPnot
ENFORCE
setting
To
amend
IR code,
follow follow
the steps
to ON for that particular OUTPUT.
14 Setthis
Although
can becan
usedalso
to fixbe
EDID
communication
IPsetting
The matrix
controlled
over LAN.
problems,
we
recommend
this
setting
for
system
debugging
Selecting the Set IP 14 button in the main
COMCTL
by the installer
and not
the end
user. and
screen
allowsonly,
access
tofor
IP operation
functionsbythat
obtains
IP address
information
necessary
for LAN control.
07 stores
EDID COPY
SETTING
– Copies EDID
information
directly from one device to another to aid transmission if
communication problems arise between incompatible devices.
Use the dropdown boxes to select which INPUT/OUTPUT
devices to copy from and where to be copied to.
14
B
B
UTP ENFORCE – used to encourage EDID/HDCP
communication between INPUT and OUTPUT devices.
Switching output settings to ON instructs the matrix
to output a signal regardless of device EDID/HDCP or
hotplug data – such information is circumvented to force
to complete the process or
communication in the event of problems between sync
to
the
process
to complete
complete the
process
or or
devices. Default setting is OFF.
If difficulties are encountered receiving a signal from a
to exit and return to the main screen.
to exit
exit and
to the
mainmain
screen.
particular source to a display, change UTP ENFORCE
to
andreturn
return
to the
screen.
setting to ON for that particular OUTPUT.
Although this setting can be used to fix EDID
Technical
Support:
US: +866 6
NOTE To accessTechnical
matrix Support:
controlsupport@wyrestorm.com
over LAN, enter the US:
+866 6
communication problems, we recommend this setting
IP
address
of
the
matrix
into
your
internet
browser
NOTE
Lock/Unlock – To gain access to Long Cable Mode settings,
To access matrix control over LAN, enter the IP
for
system debugging by the installer only, and not for
and
youmatrix
will be
to the
weband
control
screen.
press ‘unlock’ and enter
address
of the
intodirected
your internet
browser
you will
operation by the end user.
be directed to the web control screen.
‘877379’
08
A
A
1
ADVANCED OPERATION
05
FACTORY RESET – restores all matrix settings to factory
FACTORY RESET – restores all matrix settings to factory
default. This action cannot not be reversed.
Set IP The matrix can also be controlled over LAN. Selecting
the Set IP 14 button in the main COMCTL screen allows
the Set IP 14 button in the main COMCTL screen allows
access to IP functions that obtains and stores IP address
access to IP functions that obtains and stores IP address
information necessary for LAN control.
1
information necessary for LAN control.
ADVANCED OPERATION
08
08
1-Press
Press
1to
COM
CTLCTL
to read
the IRthe
codeIRfrom
thefrom
control
toinstruct
instruct
COM
to read
code
the control
system. The resulting data will appear in the central section.
system. The resulting data will appear in the central
section.
2Use your cursor to click into the box containing the IR data
you wish to change.
FACTORY RESET
– restores
all matrixsupport@wyrestorm.com
settings to factory
Technical
Support:
US:
+866
0053
EU:pointing
+44 (0)at1793
230 press
343 the
3- With
the677
remote
control
the device,
handset button you wish to transfer IR Code from and the
code will appear in your selected IR Code box.
15
1- Press
to
changes
to the
to save
savethe
the
changes
tosystem.
the system.
to save the changes to the system.
5- Hit
5- Hit
5- Hit
to close the IR Code Setting window and the device will enter
NORMAL
MODE
to close the
IR Code Setting window and the device will enter
to
close the
IR Code Setting window and the device will
NORMAL
MODE
enter NORMAL MODE
A
A
B
B A
01
01
ADVANCED OPERATION
ADVANCED OPERATION
to instruct COM CTL to read the IR code from the control
system.
TheCOM
resulting
willthe
appear
in the
central
section.
to instruct
CTL data
to read
IR code
from
the control
2Use
your
cursor
to
click
into
the
box
containing
system. The resulting data will appear in the central section. the IR
2Useyou
yourwish
cursor
click into the box containing the IR data
data
totochange.
you
wish
to
change.
2- Use your cursor to click into the box containing the IR data
youWith
wish the
to change.
3remote control pointing at the device, press
3- With the remote control pointing at the device, press the
the handset button you wish to transfer IR Code from and
handset
button
you wish
to pointing
transfer IR
Code
from press
and the
3- With the
remote
control
at the
device,
the
the code will appear in your selected IR Code box.
code
will button
appearyou
in your
IR Code
box.from and the
handset
wishselected
to transfer
IR Code
code will appear in your selected IR Code box.
4- To
Toconfirm
confirm
change,
4thisthis
change,
click click
4- To confirm this change, click
03
03
1
3
B
02
02
Receives the specific IR code used to operate the Matrix via
The resulting
code
appears
in theorwait
modify
remote
control. Can
contain
a custom
data to
code.
Third
codeparty
section
where
output
input
code can be edited
remote
control
codesand
are also
shown.
if necessary (for example if using third party control
IR code can also be input manually in the event it is
systems
B
unreadable.
01
Press
to automatically
read be
the saved
current IR
from the
NOTE
Modified
code can
ascode
a Custom
codedevice.
and read directly from a library of stored
custom
codes. code appears in the wait to modify code
01
The resulting
section
B
where output and input code can be edited if
necessary
(for example
if using third party control systems
All codes
should
be different.
3
NOTE
Modified
code can
savedsection
as a Custom
Write the
code from
the be
Modify
to thecode
device
and read directly from a library of stored custom codes.
to authorise remote control usage.
All code should be different.
NOTE All input/output boxes should contain code. If
03
Write the
code frommake
the Modify
section
to is
theno
device
to
inputting
manually,
sure
there
repetition
authorise remote control usage.
of code.
NOTE All input/output boxes should contain code. If
inputting manually, make sure there is no repetition of
code.
Modify Section - Control Commands and Code
Code input in the Input/Output section 2 and Control
codeModify
section
follow
a strict format
for the
4 must
Section
- Control
Commands
and Code
command to be understood by the system.
Code input in the Input/Output section 02 and Control
code section
must follow
a strictto
format
for theis:
04command
For reference
- the
format
be input
command to be understood by the system.
04
04
2
A
1
4
MX0808-PP
MX0808-PP
MX-0808-PP
Type “Cir” - followed by a “space” - then the “code
For reference
- the
command
number”
– and hit
the
”enter”format
key. to be input is:
number” – and hit the ”enter” key.
If the c
state s
return
S
This tra
“S”
1st byte
For exa
will fee
Read S
The co
followe
For exa
NOTE
curren
bytes)
1
2
‘\r’
‘\
Each o
input a
1, X2 =
“\r\ns
Output 1
Input 1
For example Cir 39 + ”enter” (equals a hex code of 63
Cir 0A)
39 + ”enter” (equals a hex code of 63 69
69 72For
20example
33 39 0D
72 20 33 39 0D 0A)
03
E
a command
willtell
tellthe
the matrix
matrix totoselect
thethe
nextnext
Input
SuchSuch
a command
will
select
source for Output 4
Input source for Output 4
MX0606/0808-PP Control Code
Output 1
<”08”
“09”>
1 ”00”
2 ”01”
3 ”02”
Output 2
<”18”
“19”>
1 ”10”
2 ”11”
3 ”12”
Output 3
<”28”
“29”>
1 ”20”
2 ”21”
3 ”22”
Receives the specific IR code used to operate the
Matrix via remote control. Can contain a custom or data
code. Third party remote control codes are also shown.
Output 4
<”38”
“39”>
1 ”30”
2 ”31”
3 ”32”
Output 5
<”48”
“49”>
B
1 ”40”
2 ”41”
3 ”42”
Output 6
<”58”
“59”>
1 ”50”
2 ”51”
3 ”52”
Output 7
<”68”
“69”>
1 ”60”
2 ”61”
3 ”62”
Output 8
<”78”
“79”>
1 ”70”
2 ”71”
3 ”72”
MX0606-PP
MX0606-PP
S: +866 677 0053 EU: +44 (0) 1793 230 343
16
US: +866 677 0053 EU: +44 (0) 1793 230 343MX-0606-PP 16
A
IR code can also be input manually in the event it is
unreadable.
1
Press to automatically read the current IR code from
the device.
16
4 ”03”
5 ”04”
6 ”05”
7 ”06”
8 ”07”
4 ”13”
5 ”14”
6 ”15”
7 ”16”
8 ”07”
4 ”23”
5 ”24”
6 ”25”
7 ”26”
8 ”27”
4 ”33”
5 ”34”
6 ”35”
7 ”36”
8 ”37”
4 ”43”
5 ”44”
6 ”45”
7 ”46”
8 ”47”
4 ”53”
5 ”54”
6 ”55”
7 ”56”
8 ”57”
4 ”63”
5 ”64”
6 ”65”
7 ”66”
8 ”67”
4 ”73”
5 ”74”
6 ”75”
7 ”76”
8 ”77”
MX08
Technical Support: support@wyrestorm.com US:
EU: +44
(0) 1793
230 343
Technical
Support:
US: +866 6
17 +866 677 0053
x via
ird
x via
e
eird
ed
ed if
if
ems
ms
e
ode
ode
des.
des.
ed if
ms
ed if
ms
ode
des.
ode
des.
.. If
If
of
of
If
of
If
trol
trol
of
trol
trol
3
3 69
69
put
put
3 69
3 69
put
Input 1
For example Cir 39 + ”enter” (equals a hex code of 63 69
72 20 33
39 0D 0A)is sent successfully, the current
IfIf the
control
command
If the
the control
control command
command is
is sent
sent successfully,
successfully, the
the current
current output
output
Such
a command
will
tellfeedback
the matrix
to select
the
Input
output
state
selected
will
to
show
thenext
input
state
selected
will
feedback
to
show
the
in-put
state selected will feedback to show the in-put port
port selected.
selected. The
The
source
for
Output
4
return
status
as
port
Theis
status format is as follows:
returnselected.
status format
format
is return
as follows:
follows:
2nd byte
“19”>
<”18”
Intput 3
Intput 4
Intput 5
Intput 6
Intput 7
Intput 8
03 EDID Set
3 EDID Set
1
A
S
X1
X2
‘\r’
‘\n’
SMX0606/0808-PP
X1
X2 Code
‘\r’
‘\n’
Control
If the control command is sent successfully, the current output
This
translates
as:“09”> to show the in-put port selected. The
state
selected
will
translates
as:
Output
1
<”08”
This
translates
as: feedback
IfThis
the
control
command
is sent successfully, the current output
return
status
format
is3 ”02”
as follows:
1 ”00”
2 ”01”
4port
”03”
”04”in-put
6Input
”05”
”06”
8 ”07”
state
selected
will feedback
show 5the
port
The
“S”
Outputto
port7selected.
“S”
Output port
Input port
return
status
format
is
as
follows:
1st byte
2nd byte
S
X1
X2
‘\r’ 3rd byte ‘\n’
1st
byte 2
Output
Intput 2
4
2
ADVANCED OPERATION
xx via
via
ird
ird
number” – and hit the ”enter” key.
5
3rd byte
X24 ”13”
‘\r’ 6 ”15”
2 X1
”11”
”12” “enter”
7‘\n’
”16”
For
if Cir3 44
is5 ”14”
sent successfully
This example:
translates
as:
S 1 ”10”
to the
For
For example:
example: if
if Cir
Cir 44
44 “enter”
“enter” is
is sent
sent successfully
successfully to
to the
the matrix,
matrix, itit
matrix,
it
will
feedback
“s55”
–
meaning
Output
5
has
will
feedback
“s55”
–
meaning
Output
5
has
selected
Input
This
translates
as: –“29”>
Output
3
<”28”
“S”
Output port
port Input 5.
will
feedback
“s55”
meaning
Output 5 hasInput
selected
5.
selected
Input
5.
1st1 byte
”20”
2 ”21”
2nd
byte
3 ”22”
4port
”23”
Read
“S” Status
Output
Read
Status Command
Command
1st byte
5 ”24”
2nd byte
byte
63rd
”25”
Input
port7 ”26”
8 ”07”
8 ”27”
3rd byte
The
command
length
of the
status
is
Type
“bc” -Output
4
<”38”
“39”>
Read
Status
Command
The
command
the read
read
status
is 4
4 bytes.
bytes. to
Type
For
example:
if length
Cir
44 of
“enter”
is sent
successfully
the“bc”
matrix, it
followed
by a “space”
-- and
the
key.
followed
“space”
and hit
hit
the “enter”
“enter”
key.
1feedback
”30” by a2“s55”
”31” –3meaning
”32”
4 ”33”
5 ”34”
6selected
”35”
7 ”36”
will
Output
5 has
Input 85.”37”
For example: if Cir 44 “enter” is sent successfully to the matrix, it
For
example:
bc
+
“enter”
The
command
of theOutput
read status
is 4 bytes.
ForOutput
example:
bc
+length
“enter”
will
feedback
“s55”
–“49”>
meaning
5 has selected
InputType
5.
Read
Status
Command
5
<”48”
“bc”
followed
by
a
“space”
and
hit
the
“enter”
key.
NOTE
Such
a
command
will
tell
the
matrix
to
feedback
the
NOTE
1 ”40”
3of
”42”
4 ”43”
5 ”44”
6 ”45”
7 ”46”
Such2Command
a”41”
command
tell
the
matrix
to feedback
Read
Status
The
command
length
the will
read
status
is 4 bytes.
Type
“bc” the
-8 ”47”
current
status
of
all
outputs.
See
below
for
status
format
(16
current
status
of
all
outputs.
See
below
for
status
format
(16
followed by a “space” - and hit the “enter” key.
The
command
length
of
the read status is 4 bytes. Type “bc” Output
6
<”58”
“59”>
bytes)
For
example:
bc
+
“enter”
bytes)
followed
by a2bc
“space”
- and hit
the “enter”
key.
For1 example:
+ “enter”
”50”
”51”
3 ”52”
4 ”53”
5 ”54”
6 ”55”
7 ”56”
8 ”57”
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
1
2 Such
3 4 a command
6 7
8
9tell
10the
11 12 13to14 15
NOTE
NOTE
For
example:
+ 5“enter”
Suchbc
a command
will will
tell the
matrixmatrix
to feedback the
‘\r’Output
‘\n’ 7 s <”68”
X1 X2 “69”>
s X3
X4 s X5 X6 s
X7 X8 ‘\r’
‘\r’ ‘\n’ s the
X1 current
X2 s X3status
X4 sof X5
X6 s
X7 See
X8 ‘\r’
feedback
all
outputs.
current
status
of
all
outputs.
See
below
for
status
format
(16
NOTE Such a command will tell the matrix to feedback
the
1 ”60”
2 ”61”
3 ”62”
4 ”63”
5 ”64”
6 ”65”
7 ”66”
8 ”67”
bytes)
below
for
status
format
(16
bytes)
Each of status
the X1,
X4, X5,
X6,below
X7, X8for
signifies
related
current
ofX2,
allX3,
outputs.
See
status the
format
(16
3
16
16
‘\n’
‘\n’
Each of the X1, X2, X3, X4, X5, X6, X7, X8 signifies the related
input
as 8chosen
by a “79”>
specific output:
X1 =
Out-put
Output
<”78”
bytes)
input
output:
Out-put
1
2as chosen
3 4 by5 a specific
6 7
8
9 X1
10 =11
12 13 14 15 16
1,
X2
=
Output
2
etc.
For
example,
a
status
reading
of
1,‘\r’X2
=
Output
2
etc.
For
example,
a
status
reading
of
1 ”70”
2
”71”
3
”72”
4
”73”
5
”74”
6 ”75”
7 ”76”X8 8‘\r’
”77” ‘\n’
‘\n’
s
X1
X2
s
X3
X4
s
X5
X6
s
X7
1
2
3 4
5
6 7 signifies
8
9 the
10following
11 12
13
14 15 16
“\r\ns12s22s53s45\r\n”
matrix
“\r\ns12s22s53s45\r\n” signifies the following matrix settings.
settings.
MX0808-PP
‘\r’ ‘\n’ s X1 X2 s X3
X4 s X5 X6 s
X7 X8 ‘\r’
‘\n’
Each
theX1,
X1,
X2,
X3,
X4,
X5,
X6,5X8
X7,
X86 signifies
Each
X3,
X5,4Support:
X6,
X7,
signifies
the 7related
Technical
Output
Output
2 X2,
Output
3 X4,
Output
Output
Output
Output
Output 8 US: +866 677 0053 EU: +44 (0) 1793 230 343
17 of1ofthe
Output 1 Output 2 Output 3 Output 4 Output 5 Output 6 Output 7 Output 8
inputrelated
as chosen
by a specific
output:
X1 = Out-put
the
input
by aX7,specific
output:
X1
Each of the X1,
X2,as
X3,chosen
X4, X5, X6,
X8 signifies
the related
1,Input
X21= Output
2Intput
etc.
For
example,
aFor
status
reading
of status
Intput
2
3
Intput
4
Intput
5
Intput
6
Intput
7
Intput
8
=
Output1,
X2
=
Output
2
etc.
example,
a
input
a specific
= Out-put
Input 1as chosen
Intput 2 by
Intput
3 Intput output:
4 Intput X1
5 Intput
6 Intput 7 Intput 8
“\r\ns12s22s53s45\r\n”
signifies
the
following
matrix
settings.
reading
of “\r\ns12s22s53s45\r\n”
1, X2 = Output
2 etc. For example, a statussignifies
reading ofthe following
“\r\ns12s22s53s45\r\n”
signifies
the
following
matrix7settings.
matrix
settings.
03
EDID
Set
Output 1 Output 2 Output 3 Output 4 Output 5 Output 6 Output
Output 8
03
EDID Set
Output 1 Output 2 Output 3 Output 4 Output 5 Output 6 Output 7 Output 8
Input 1
Intput 2 Intput 3 Intput 4 Intput 5 Intput 6 Intput 7 Intput 8
Input 1
03
03
Intput 2
Intput 3
Intput 4
Intput 5
Intput 6
Intput 7
Intput 8
EDID Set
EDID Set
put
”07”
”07”
”07”
”07”
MX-0606-PP
07”
Pressing the EDID SET button 16 in the COM CTL
main screen allows user access to EDID settings that can
be read, saved and recalled.
”27”
07”
”27”
07”
”37”
07”
”37”
27”
1
Select your OUTPUT port (the output port is always
the first to be selected by default on entering EDID set)
”47”
27”
”47”
37”
2 Press “Read EDID” to read EDID from the selected
output port. The status bar shows the progress of the
EDID read.
”57”
37”
”57”
47”
”67”
47”
”67”
57”
”77”
57”
”77”
67”
MX0808-PP
MX0808-PP
om
US:
om
US: +866
+866 677
677 0053
0053
67”
MX0808-PP
EU:
EU: +44
+44 (0)
(0) 1793
1793 230
230 343
343
17
3
Once completed, the EDID appears here.
ADVANCED OPERATION
NETCTL - LAN Control
The matrix can also be controlled via LAN over a network/
web browser using the supplied Wyrestorm NET CTL
software or LAN protocols from third party companies,
such as Control 4.
4
Then select your INPUT port and press
“Download” to send the EDID to your input
5
Press “Save As” to save the EDID as a ‘BIN file’
ATTENTION Use a ‘straight through’ ethernet cable
for switch/router connection and a ‘cross-over’
cable for connection to a PC. Using the incorrect
cable will not damage your equipment, but it may
result in poor/no connection.
A
Alternatively, you can open EDID from here if
you have previously saved output EDID in bin format.
Recommended if you frequently need to use specific
output EDID, from a particular display, for example
17 IR Matrix – manually connects INPUT IR RX ports
to Output Display Receiver IR TX ports – this function is
available when the matrix is connected to display receiver
via the HDBT OUT Cat5e/6/7 port.
IR Matrix allows manual selection of source device IR RX
ports 1 by Display Receiver IR TX ports 2
The dropdown menu 3 allows ALL IR TX ports to be
set to ONE specific INPUT device IR RX port with the
current settings of the IR Matrix viewable by pressing the
STATUS button 4
4
ADVANCED
ADVANCED
OPERATION
OPERATION
3
MX-0808-PP
On initial opening, the program will first create a NETCTL.
TXT file that will serve as a device backup for future use;
including connection settings such as IP address and
MAC address of the MX0606/0808-PP, as well as its
name if you decide to change the name of your matrix
(see Device Name section below).
On subsequent openings, NETCTL will then search the
Matrix for the saved data required for connection.
2
1
Make sure that your LAN cable is correctly
terminated and firmly connected to ports before
running the software.
If using for the first time, the program will automatically
thethe
IPfirst
address
being
used,
the result
Ifdetect
using for
time, the
program
willwith
automatically
detect the
displayed
in
the
white
area
beneath.
IP address being used, with the result displayed in the white area
If using for the first time, the program will automatically detect the
beneath.
IP address being used, with the result displayed in the white area
Should no result appear or if the system is unable to
Should
beneath.no result appear or if the system is unable to detect an IP
detect automatically,
an IP address
automatically,
press the
address
press
the
Should no result appear or if the system is unable to detect an IP
address automatically, press the
button
locate.
buttontoto
locate.
When the
IP address appears, click
button
to locate.
When the IP address appears, click
to attach the IP address to the system and the IP address
will change to a default factory serial number MX0606-PP or
MX0606_HE1 / MX0808-PP or MX0808_HE1
MX-0606-PP
Device Name / MX0808-PP or MX0808_HE1
MX0606_HE1
18
Device Name
On eith
numbe
On eith
will be
numbe
will be
ADVANCED OPERATION
will change to a default factory serial number MX0606-PP
or MX0606_HE1 / MX0808-PP or MX0808_HE1
Device Name
ADVANCED OPERATION
Should you wish to change the name of your matrix from the
factory default, just right click on the serial number and select
‘rename’ from the dropdown menu. Input the new name and press
OK.
In some systems these settings can be accessed through the
included Netfinder.exe application. Click
Missing image
Enter the default password of ten zeros
‘0000000000’
‘0000000000’
and click
and
click
to
to to
thethe
NETCTL
matrix
controller
screen. screen.
totake
takeyou
you
NETCTL
matrix
controller
to locate the device IP address.
Should you wish to change the name of your matrix from
the factory default, just right click on the serial number
select
‘rename’
from
the dropdown
menu.detect
Inputthe
the
Ifand
using
for the
first time, the
program
will automatically
new
namebeing
andused,
presswith the result displayed in the white area
IP
address
beneath.
OK.
In some
these
can
be accessed
Should
no systems
result appear
or ifsettings
the system
is unable
to detectthrough
an IP
the included
Netfinder.exe
address
automatically,
press the application. Click
19
On either system, when the device name/default factory serial
number appears, double click (or right click and OPEN) and you
will be directed to a web login page in your internet browser.
EU: +44 (0) 1793 230 343
button
to locate.
to locate
the device IP address.
On either system, when the device name/default factory
serial number appears, double click (or right click and
to
attach and
the IP
address
to directed
the systemtoand
the IPlogin
address
OPEN)
you
will be
a web
page in
your internet browser.
MX0606_HE1 / MX0808-PP or MX0808_HE1
Device Name
The layout of NET CTL includes an upper section to
allocate input sources to output with the selection
displayed on the left hand side.
Operation is the same as COM CTL – Inputs buttons 1-4
can be clicked to be selected per Output port.
Press the button to update your chosen matrix settings
into the left hand display and your selection to take effect.
TELNET Control
For TELNET Control, the matrix IP address is as follows:
Should you wish to change the name of your matrix from the
factory default, just right click on the serial number and select
‘rename’ from the dropdown menu. Input the new name and press
OK.
In some systems these settings can be accessed through the
included Netfinder.exe application. Click
‘0000000000’
and click
to take you to the NETCTL matrix controller screen.
to locate the device IP address.
19
The layout of NET CTL includes an upper section to allocate input
sources to output with the selection displayed on the left hand
side.
Operation is the same as COM CTL – Inputs buttons 1-4 can be
clicked to be selected per Output port.
ADVANCED OPERATION
Press the button to update your chosen matrix settings into the
left hand display and your selection to take effect.
TELNET Control
click to confirm IP settings
ATTENTION This ‘Assign IP’ process differs from the COM
EDID
CTL ‘IPDIP
Set’Switch
function.settings
‘Set IP’ in COMCTL saves/reads the IP address in flash and
Distribution of HD signals through the matrix requires
sets it as static IP. ‘Assign IP’ is only used when the system
mutual communication or ‘handshake’ between source
fails to obtain an IP address automatically and is NOT saved
and
display. If there is any disparity between the two,
in flash.
successful transmission becomes problematic.
EDID DIP Switch settings
For TELNET Control, the matrix IP address is as follows:
Once activated, the matrix can be controlled in the
Control Command format.
Distribution
HD signals
throughwith
the matrix
requires
mutual
This
matrix ofcomes
equipped
an EDID
DIP switch
communication
or
‘handshake’
between
source
and
display.
If
for manual adjustment of matrix settings to encourage
there is any disparity between the two, successful transmission
communication between INPUT and OUTPUT devices. If
becomes problematic.
installation compatibility issues arise, check the settings
Thisyour
matrix
comes equipped
withand
an EDID
manualas
on
connected
devices
adjustDIP
theswitch
DIP for
settings
adjustment
of
matrix
settings
to
encourage
communication
required.
between INPUT and OUTPUT devices. If installation compatibility
issues arise, check the settings on your connected devices and
ATTENTION
Changes to the DIP switch settings
adjust the DIP settings as required.
should be made with the matrix OFF, to guard
ATTENTION Changes to the DIP switch settings should
against electrostatic
build up that may damage
be made with the matrix OFF, ideally with all power cables
your system. DO NOT HOTSWAP your cables when
and HDMI leads and UTP cables removed to guard against
changing
SETTINGS.
electrostaticDIP
build
up that may damage your system. DO NOT
HOTSWAP your cables when changing DIP SETTINGS.
Once activated, the matrix can be controlled in the Control
Command format.
ALL changes to the DIP settings become effective
ALL changes to the DIP settings become effective upon
upon
powering ON the matrix.
powering ON the matrix.
ON
DEFAULT ON
ON
OFF
1
Click
Click
Click
Click
to
to return
return without
without changes
changes taking
taking effect.
effect.
to
return
without
changes
taking
effect.
to return
without
changes
taking
effect.effect.
to
return
without
changes
taking
Now
click
Now
Now click
click
Now click
for
theclick
Matrix
detect
the
new
IP
address,
will
appear
in
Now
forto
Matrix
to detect
the which
new IP
for
to
detect
the
IP
which
will
appear
for the
the Matrix
Matrix
tothe
detect
the new
new
IP address,
address,
which
willaddress,
appear in
in
the
dialog
box.
Finally
for
the
Matrix
to
detect
the
new
IP
address,
which
will
appear
in
the
Finally
which
willbox.
appear
the dialog
dialog
box.
Finallyin the dialog box. Finally, click
input
input
input
d
input
d
d
d
be
be
be
be
he
he
he
he
ADVANCED
ADVANCED
ADVANCED
ADVANCED
OPERATION
OPERATION
OPERATION
OPERATION
to assign the new IP address to the system and you will return to
3
4
ON
Click
to assign
assign
the
new
IP address
address
to the
thetosystem
system
and you
youand
will return
return
to
to
the
new
IP
to
and
will
to
to
assign
the
new
IP address
the system
you will
the
previous
to
thescreen
new IPor
theassign
previous
screen
oraddress to the system and you will return to
the
previous
screen
or
return
to the
previous
the previous
screen
or screen or
2
1
2
3
4 2
31 4
Shaded DIP setting denotes
inactive switch so position can be
setON
to up or down
(Default factory setting)
(Default factory setting)
EDID
display
(Force
1 Copy
2 3from
4 Output
1 2to Input
3 Input
4port port
EDID
from
Output display
to
(Force
SignalCopy
Output
mode)
Signal Output mode)
To copy the EDID from an HDMI OUTPUT display to a specific
ON
ON
INPUT port, first set the DIP switch to this position. Then select
To
copy
the
EDID
from
an
HDMI
OUTPUT display to
the INPUT by pressing and holding the chosen OUTPUT
aSELECT
specificbutton
INPUT
first set
theEDID
DIP to
switch
to this
for port,
3 seconds
for the
be copied
from the
position.
Then
select
the
INPUT
by
pressing
and
holding
DISPLAY
port. 1 2 3 4
1 2 to 3the INPUT
4
the chosen OUTPUT SELECT button for 3 seconds for
the EDID to be copied from the DISPLAY to the INPUT
ON
ON
port.
the dialog box. Finally
20
click
to
confirm
IP
settings
click to
to confirm
confirm IP
IP settings
settings
click
to
confirm
IP settings
For example: If OUTPUT 3 is selected for INPUT 1, the
click
to confirm
IP settings
ATTENTION
This
‘Assign
IP’
process
differs
from
the
COM
ATTENTION This
‘Assign
IP’
process
differs
from
the
COM
ATTENTION
EDID
1 – this
1 for2 OUTPUT
3 4 3 will be copied
This ‘Assign IP’ process differs from the COM
1 2 to
3 INPUT
4
ATTENTION
CTL
‘IP Set’
function.
This ‘Assign IP’ process differs from the COM
CTL
CTL ‘IP
‘IP Set’
Set’ function.
function.
ATTENTION
This ‘Assign IP’ process differs from the is achieved by the system setting HDMI OUTPUT as a
CTL ‘IP Set’ function.
‘Set
in
saves/reads
COM
‘IP Set’
function. the
higher
‘Set IP’
IP’CTL
in COMCTL
COMCTL
saves/reads
the IP
IP address
address in
in flash
flash and
and
‘Set
IP’
in
COMCTL
saves/reads
the
IP
address
in
flash
and
ONpriority than UTP OUTPUT.
ON
ON
sets
it
as
static
IP.
‘Assign
IP’
is
only
used
when
the
system
‘Set
IP’
in
COMCTL
saves/reads
the
IP
address
in
flash
and
sets it
it as
as static
static IP.
IP. ‘Assign
‘Assign IP’
IP’ is
is only
only used
used when
when the
the system
system
sets
fails
to
obtain
an
IP
address
automatically
and
is
NOT
saved
sets
it as
staticanIP.IP‘Assign
IP’automatically
is only used when
the
system
fails to
to
obtain
address
and
is
NOT
saved
‘Set
IP’
in COMCTL
saves/reads
theand
IP is
address
If EDID copy is not successfully completed, the INPUT
fails
obtain
an IP address
automatically
NOT
saved
in
flash.
fails
to
obtain
an
IP
address
automatically
and
is
NOT
saved
in
flash.
in
flash.
in
flash and sets it as static IP. ‘Assign IP’ is only
Port EDID will remain the unchanged.
in flash.
EDID
DIP
Switch
settings
1 2 3 4
1 2 3 4
1 2 3
used
when
the
system
fails
to
obtain
an
IP
address
EDID
DIP
Switch
settings
Distribution
of
HD
signals
through
the
matrix
requires
mutual
automatically
and
is
NOT
saved
in
flash.
Distribution
Distribution of
of HD
HD signals
signals through
through the
the matrix
matrix requires
requires mutual
mutual
communication
or
‘handshake’
between
source
and display.
If
Distribution of HD
signals through
the matrix
requires
mutual
communication
or
‘handshake’
between
source
communication or ‘handshake’ between source and
and display.
display. If
If
there
is
any
disparity
between
the
two,
successful
transmission
communication
or ‘handshake’ the
betweensuccessful
source and display. If
there
there is
is any
any disparity
disparity between
between the two,
two, successful transmission
transmission
becomes
problematic.
there is any
disparity between the two, successful transmission
becomes
problematic.
This
This matrix
matrix comes
comes equipped
equipped with
with an
an EDID
EDID DIP
DIP switch
switch for
for manual
manual
This
matrix
comes
equipped
with
an
EDID
DIP
switch
for
manual
adjustment
of
matrix
settings
to
encourage
communication
This
matrix
comes
equipped
with
an
EDID
DIP
switch
for manual
Technical
Support:
US: +866 677 0053 EU: +44 (0) 1793 230 343
20
adjustment of
of matrix
matrix settings
settings to
to encourage
encourage communication
communication
adjustment
between
INPUT
and
OUTPUT
devices.
If
installation
compatibility
adjustment
of
matrix
settings
to
encourage
communication
between INPUT
INPUT and
and OUTPUT
OUTPUT devices.
devices. If
If installation
installation compatibility
compatibility
between
issues
check
the
settings
on
devices
and
between
INPUT
and
OUTPUT
installation
compatibility
issues arise,
arise,
check
the
settingsdevices.
on your
your Ifconnected
connected
devices
and
issues
arise,
check
the
settings
on
your
connected
devices
and
adjust
DIP
settings
as required.
issues the
arise,
check
the settings
on your connected devices and
4
For example: If OUTPUT 3 is selected for INPUT 1, the EDID
ADVANCED
ADVANCED
OPERATION
OPERATION
ADVANCED
ADVANCED
OPERATION
ADVANCED
OPERATION
OPERATION
ADVANCED
OPERATION
ADVANCED
OPERATION
To reset EDID for all ports, simply set the DIP switch to
for OUTPUT 3 will be copied to INPUT 1 – this is achieved by
the
above position when the matrix is powered OFF. On
the system setting HDMI OUTPUT as a higher priority than UTP
powering
ON,
all ports3will
revert to
above
factory
ON
OUTPUT.
For
example:
If OUTPUT
is selected
forthe
INPUT
1, the
EDID
default
and DIP
be adjusted
asachieved
necessary.
for OUTPUT
3 willswitches
be copiedcan
to INPUT
1 – this is
by
unable to achieve 1080p resolution (such
ADVANCED OPERATION
RESETTING TO FACTORY DEFAULT:
OFF
turn
on 1
for EDID
1ON2 3 4
DEFAULT
2
3settings
4 ONto take effect.
ON
1ON
2
3
4
1 DEFAULT
2 3 4ON2 31 4
ON
ON
ON
ON
1 2 3 4
ON 1 2 3 4
1ON2 3 4
1ON2 L-series
3 4 EDID)ON
OFF
1080i Stereo
embedded
1080i
Stereo(using
(using
embedded
L-series EDID)
OFF
ON
ON
DEFAULT
ON
1 2 3 4
1 2 3 4ON2 31 4
ON
111 222 333 444 In instances
1 2where
2 333 a44connected
4 2 31 display
4
is
ON 11embedded
1080p
D-series EDID)
ON 5.1ch Audio (using
ON2 where
In instances
a connected display
1 2 3 4
OFF
1older
4position
When
set
to2this
1theresolution
2matrix
3 4
is
unable
achieve
1080p
as
using
or3DIP
cheaper
models),
ON
ON
ON
ONto
ONthis
ON
11ON22 33 44 DIP
1
2
3
4
1
2
3
4
2
3
1
4
will
use
embedded
1080p
video
with
5.1ch
1
2
3
4
setting
will
instruct
the
matrix
to
use
using older
or cheaper
ON(such
1080p DEFAULT
5.1ch Audio
(usingas
embedded
D-series
EDID)
Audio EDID.
1 2 3 4
1ON
2 DIP
3 video
4setting
embedded
1080i
and stereo
audio
ONinstruct
models),
this
will
ON ON
When
set
to
this
DIP
position
the
matrix
EDID
to
output
a
signal.
ON
ON
ON
After setting
the DIPvideo
switch,
reconnect
the11ON
matrix
embedded
and
stereo and
audio
ON21080i
ON
ON
OFF
2 33to use
2DEFAULT
44 ON
44
will use11embedded
1080p
video
2 333settings
1 with
2 5.1ch
3 4
ON
1
2
3
4
1
2
4
DEFAULT
ON
turn
on
for
EDID
to
take
effect.
ON
ON
After
EDID1to 2output
signal.
3 4aON
2 31setting
4 the DIP switch, reconnect and
ON
Audio
EDID.
DEFAULT
ON
turn
on
for
EDID settings to take
effect.
1
2
3
4
1
1 EDID)
2 3 4
1080p
(using embedded
ON 7.1ch Audio After
ON2 the3DIP4G-series
OFF
ON 1ON
setting
switch, reconnect and
2
3
4
ON
1
2
3
4
DEFAULT
ON
After
switch,
and turn
OFF
2this33DIP
1the effect.
2on 3for 4
11 1setting
22 2 33 3the
44 4 DIP
11for
2reconnect
44position
2 3on
1 set
4 toEDID
When
matrix
turn
settings
to take
OFF
1 ON
2 2 3 3 4to4 take
1settings
2
3
1
4
ON
EDID
effect.
1
2
3
4
1
2
3 4
DEFAULT ONWhen set to this DIP position the matrix
1
2
3
4
2
3
1
4
1080p
7.1ch
Audio
(using
embedded
G-series
EDID)
DEFAULT
ON
ON
ON
Technical
Support:
21 ON
OFF
will use embedded
1080p video with 7.1ch US: +866 6
ON
1ON2 3 4
1ON2 3 4
ON
1 125.1ch
4Audio
1080p
5.1ch
(using
D-series
EDID)
1embedded
4D-series
1080p
(using
EDID)
Audio
EDID.
23 3Audio
4 When
2
31 set
4 to2embedded
this3 DIP
position
the
matrix
OFF ON
When set to this DIP position the matrix
OFF 1ON2 3 4 When
setON
the matrixand
the DIP
DIP position
switch, reconnect
1 DEFAULT
2 3 4ONAfter
2 31setting
4to this
ON
ON
ON
will
use
embedded
1080p
video
with
7.1ch
1 2 2 3 3 4 4 will
2 use
3on
1 1set
4 EDID
When
to this
DIP
position
the5.1ch
matrix
1ON
ON
2
3
4
embedded
1080p
video
with
turn
for
settings
to
take
effect.
1080p
5.1ch
(usingEDID.
1 ON2DEFAULT
3 Audio
4 ONAudio
ON
1embedded
2 3 4D-series EDID)
1ON2 3 4
will use
embedded 1080p video with
Audio
EDID.
1ON2 Output
3 4 When set to this DIP position the matrix
ONNormal
OFF
5.1ch
Audio
EDID.
After setting
the
DIP switch, reconnect
and
ON
ON the
ON
1ON
2
After
setting
DIP
switch,
reconnect
and
ON
ON
will
use
embedded
1080p
video
with
5.1ch
2 33 3 44 4ON
2
3
1
4
1 1 DEFAULT
2DEFAULT
1
2
3
4
OFF
2
3
4
1
2
3
4
turn
on11for
EDID
settings
to
take
effect.
1080p
(using
embedded
D-series
EDID)
1 ON
25.1ch
3 Audio
4 ONAudio
2
3
4
turn onEDID.
for EDID settings
to take
effect.
1080p
5.1ch
(using
D-series
EDID)
1ON
2 2 3 3Audio
4 4 DIP
1setting
2 switch,
31 embedded
4 reconnect
ON
ON
After
the
and
DEFAULT
ON
1
2
3
4
Normal
Output
ON7.1ch
When
set to this DIPG-series
position the
matrix
1080p
AudioWhen
(using
EDID)
After
setting
the DIP
DIP
switch, reconnect
setembedded
totake
this
position
the
matrix and
ON
ON
OFF
turn
on
settings
to
effect.
1ON
ON
ON
DEFAULT
OFF
11ON
222for333EDID
444 ON
will use 1embedded
1080p
video
with
ON
ON
2
3
4
1
2 5.1ch
3 4
1 ON
2DEFAULT
4 4ON
turn
on 1
for
settings
to
take
effect.
2this3DIP
4D-series
will
use
embedded
1080p
video
with
5.1ch
11 DEFAULT
22 33 33Audio
2(using
44toEDID
When
position
the
matrix
1080p
embedded
EDID)
2 3311set
ON
ON
Audio
EDID.
1ON
25.1ch
4 4ON
OFF
DEFAULT
ON
Audio
EDID.
ON
1ON27.1ch
3 4Audio
When
set
to this DIPG-series
position
the
matrix
1080p
(using
embedded
EDID)
1080p
7.1ch
G-series
EDID)
ON
1 DEFAULT
2 3 3Audio
4ONWhen
2 (using
31setting
4toembedded
OFF
setembedded
this
position
thewith
matrix
ON 1ON
After
the DIP
DIP
switch,
reconnect
and
2
4
ON
will use
1080p
video
7.1ch
DEFAULT
ON
ON
ON
OFF
1
2
3
4
After
setting
the
DIP
switch,
reconnect
1for
2this3DIP
4position
1thewith
2 5.1ch
3and4
Output
1ON
2
3
4
DEFAULT
ON
will
use
embedded
1080p
video
1
2
3
4
2
3
1
4
ON
ONForce
When
set
to
matrix
OFF
1
2
3
4
turn
on
EDID
settings
to
take
effect.
1
2
3
4
1
2
3
4
Audio
EDID.
OFF 1ON
1 DEFAULT
2 3 3 4 4ON
2 on
31EDID.
4 EDID
turn
for
settings
to take effect.
ON
ON
2DEFAULT
When
set
to
this
DIP
position
the matrix
ON
Audio
When
set
to
this
DIP
position
the
matrix
1
2
3
4
2
3
1
4
ON
1
2
3
4
1
2
3
4
Instructs
the
Matrix
to
Output
a
signal
OFF
1 DEFAULT
2 3Audio
4ON
2 31setting
4 the DIPG-series
ON
ON
ON
1080p
7.1ch
(using
embedded
EDID) and
DEFAULT
ONAfter
switch,
reconnect
When
set
tocommunication
this1080p
DIP
position
the7.1ch
matrix
OFF
will
useembedded
embedded
video
with
1080p
7.1ch
G-series
EDID)
ON
1ON
2 2 3Audio
4 4 (using
regardless
of
between
1
3
2
3
1
4
After
setting
the
DIP
switch,
reconnect
and
OFF
ON
ONForce
turn
on
for
settings
to take
effect.
OFF
11ON
22Output
Audio
EDID.
1 DEFAULT
2 33 3 44 4ONturn
2will
3on
1 set
4embedded
ON
When
toEDID
this3DIP
position
the
matrix
1for
2
4
1
2
3
4
use
1080p
video
with
display
and
source
compatibility.
This
settings
to take
effect.
OFF 111ON
1ON
22 3311ON
ON
set4 toEDID
this DIP
position
the matrix
33333 44444 When
22222Output
1 2DEFAULT
4
ON
OFF
When
set
to
this
DIP
position
the
matrix
OFF
1ON
3
4
setting
may
be
used
to
further
encourage
7.1ch
Audio
EDID.
Normal
Instructs
the
Matrix
to
Output
a
signal
ON
After
the DIP
DIP position
switch, reconnect
1 DEFAULT
2 3 4ON
2 31setting
ON
When
set 4to this
the matrix and
1080p
7.1ch
G-series
EDID)
11 DEFAULT
2will
3311 embedded
44 ofbetween
222 3333Audio
use
embedded
1080p
video
with 7.1ch
11ON
2
4444ON(using
2regardless
ON
compatibility
devices
if with
other
DIP
communication
between
OFF
ON
turn
on
for
EDID
settings
to
take
effect.
will
use
embedded
1080p
video
7.1ch
ON 1ON
2
3
4
ON
ON
Audio
EDID.
settings
prove
unsuccessful
in
establishing
ONAfter
ON
display
and
source
compatibility.
This
11ON
22 2 33 3 the
4 4 Audio
1 setting
2 switch,
31ON
When
set4 to reconnect
this DIP position
and the matrix
EDID.
ON
OFF
11ON
22 Output
33 444 DIP
Normal
1ON
2to this
3 used
4 position
OFF
communication.
setting
may
be
to
further
encourage
ON
When
set
DIP
the
matrixand
1
2
3
4
ON
After
setting
the
DIP
switch,
reconnect
OFF
turn
settings
effect. reconnect
11ON
22for
1on
2 33EDID
3 44 4
4ON
2compatibility
3setting
1 to
4 take
ON
DEFAULT
After
the
DIP switch,
and
1
2
3
2
3
1
4
ON
between
devices
if
other
DIP
will
use
embedded
1080p
video
with
7.1ch
turn
on
for
EDID
settings
to
take
effect.
1 222 333settings
2 no3on
1ON
4 EDID settings to take effect.
ON
function
11ON
444 turn
ON
for
ONRemaining
settings
prove
unsuccessful
in
establishing
ON
Audio
1 EDID.
2 3 4
(reserved
future
updates)
11ON
22 Output
33for 444
11
22
33
Normal
Output
Normal
1ON2 3 4
ON
11ON
22Output
33 444
communication.
OFF
Normal
ON
1ON
setting
2 the
3 DIP
4 switch, reconnect and
ON2222 3333 4444 After1ON
1111
ON
1 Output
2 3 3settings
4 turn
2 no3on
1function
4 EDID settings to take effect.
Force
2
4
Remaining
ON
for
ON2 3 4
1ON
1 2 3 4
111ON222 333for444
(reserved
future updates)
ON
11ON
22 Output
33 44 Instructs the Matrix to Output a signal
Normal
ON
2 33 44 regardless
1ON2 of3communication
4
between
ON2
11ON
Force
Output
1
ON2
1
2 333 444
1 2 3 4
11ON
2
display
and
source
compatibility.
This
ON
2
3
4
ON
ON
111ON
222 333 444
Instructs
thebe
Matrix
signal
ON
setting may
usedtotoOutput
furtheraencourage
ON2 3 4 regardless of communication between
1ON
compatibility between devices if other DIP
11ON
22Output
33 44
Force
ON
1ON
2Output
3 44 display
1ON
2prove
3 unsuccessful
4 compatibility.
source
This
Force
Force
1
2
3
ONOutput
ONand
settings
in establishing
1ON
2
3
4
ON22
11
33
44
setting
may
be
used
to
further
encourage
Instructs
the
Matrix
to
Output
a
signal
1
2
3
4
1
2
3
4
communication.
ON
11ON
22 33 44 Instructs
ON
ONthe Matrix to Output a signal
ON
compatibility
if other
DIP
regardless
ofbetween
communication
between
Instructs
the
Matrix devices
to Output
a signal
1
2
3
4
ON
regardless
of communication
between
1
2
3
4
ON
ON
Remaining
settings
no
function
Force
Output
settings
prove
unsuccessful
in
establishing
display
and
source
compatibility.
This
11ON
2
3
4
ON2
ON
3 4
regardless
between
and
11ON
22 source
33of communication
44 compatibility. This
(reserved
future
updates)
1ON
2 33for 4
4 display
11
22
communication.
setting
may
be
used
toOutput
furtheraencourage
ON
ON
1ON
2 33 44 setting
Instructs
the
Matrix
to
signal
may
used tocompatibility.
further encourage
andbesource
This
1ON
4 display
compatibility
devicesbetween
if other DIP
2 333
3 settings
1ON
2 of3between
4
ON222
111ON
444 compatibility
regardless
communication
Remaining
noON
function
between
devices
if other DIP
setting
may
be
used
to
further
ON
1
settings
prove
unsuccessful
in establishing
1ON2
2 3
3 4
4 settings
1ON
2prove
3 unsuccessful
4 compatibility.
display
source
This
(reserved
updates)
in
establishing
ONand
11ON22 33for
4future
encourage
compatibility
between
devices
if
other
4
1
2
3
4
communication.
ON
ON
11ON
22 33 44 communication.
11ON
22 3be
4
setting
may
used
to further encourage
ON
ON 3 4in establishing
DIP1ON
settings
prove
unsuccessful
2 3
3 settings
4 compatibility
devices if other DIP
1
2
4
Remaining
no1 function
1
2
3
4
2 3between
4
11ON22 33settings
44
Remaining
no1ON
function
communication.
2
3
4
settings
prove
unsuccessful
in establishing
(reserved
for 4future updates)
11 22 3for
11 22 33 44
(reserved
future
updates)
3
4
communication.
ON2 3 4
ON2 3 4
1ON
1ON
11ON
22 33 settings
44
11ON
33 44
Remaining
no22function
1 2 3 settings
4
Remaining
no function
(reserved
for
future
1 2 3for
4
1updates)
2 3 4
(reserved
future
updates)
If EDID copy is not successfully completed, the INPUT Port EDID
the system setting HDMI OUTPUT as a higher priority
ON than UTP
will remain the unchanged.
ON
OUTPUT.
AVR 7.1 Audio EDID COPY to Blu-ray source
1ON2 3(AV4
RESETTING
TO
FACTORY
DEFAULT:
Receiver
copy)
If EDID copy
is not successfully completed, the INPUT Port EDID
ON to the above
To reset
EDID
all ports, simply set the DIP switch
will
remain
the for
unchanged.
1ON2 3 4
position
when
matrix
powered
OFF.
Onan
powering
ON,
1AV
3 all
4
For
users
whothewish
to iscopy
EDID
from
ON2Receiver
RESETTING TO FACTORY DEFAULT:
1DIP
3 4can
ports7.1channel
will revert to audio
the above
default
andport
switches
ON2containing
with
to afactory
specific
input
be reset
adjusted
as for
necessary.
To
EDID
all
ports,asimply
set the
to the above
aFor
Blu-ray
player,
follow
onDIP
theswitch
instructions
example:
If OUTPUT
3 isvariation
selected for
INPUT
1, the
1ON
2 EDID
3 4
ON
position when the matrix is powered OFF. On powering
all
1ON
2 ON,
3 by
4
for
OUTPUT
3 will
be copied
INPUT
1 –source
this is
achieved
AVR
7.1 Audio
EDID
COPYtoto
Blu-ray
(AV
Receiver
above:
2switches
3 4can
ports will revert to the above factory default and 1DIP
ON
the
system setting HDMI OUTPUT as a higher priority
copy)
1 2 than
3 UTP
4
be adjusted
necessary.3 is selected for INPUT ON
For
example:as
If OUTPUT
1, the EDID
1isON
2 the
3 matrix
4
1OUTPUT.
Set
the who
DIP
switch
to the
above
with
For
users
wish
tocopied
copy
EDID
from position
an
AV
Receiver
with
7.1
for
OUTPUT
3
will
be
to
INPUT
1
–
this
achieved
1ON
2 Receiver
3 by4
AVR 7.1 Audio EDID COPY to Blu-ray source
(AV
EDID
copy
is
not
successfully
completed,
the
INPUT
Port
EDID
inIfthe
the
OFF
position.
channel
audio
to
a
specific
input
port
containing
a
Blu-ray
player,
system setting HDMI OUTPUT as a higher priority
UTP
ON22 than
copy)
11ON
33 44
will
remain
theIf unchanged.
follow
a variation
on the instructions
OUTPUT.
For
example:
OUTPUT
3 is selectedabove:
for INPUT ON
1, the EDID
For
example:
If OUTPUT
3 isEDID
selected
INPUT
1,
the
ON
1is
22 EDID
33onby
44the
For
users who
wish
tocopied
copy
fromforan
with
7.1
OUTPUT
3TO
will
be
to
INPUT
1OUTPUT
–AV
thisReceiver
achieved
2for
the
AVR
your
desired
port
1ON
RESETTING
FACTORY
DEFAULT:
1Connect
Set
the
DIP
switch
totothe
above
position
with
the
matrix
in
the
ON
If
EDID
copy
is
not
successfully
completed,
the
INPUT
Port
EDID
for
OUTPUT
3
will
be
copied
to
INPUT
1
–
this
is
achieved
by
channel
audio
to a HDMI
specific
input port
a Blu-ray
player,
the
system
setting
OUTPUT
ascontaining
a higher priority
than
UTP
matrix
(for
example,
OUTPUT
2)
1
2
3
4
OFF
position.
ON
ON
will
remain
the
unchanged.
the
system
setting
HDMI
OUTPUT
asabove:
a higher
priority
To
reset
for on
all
ports,
simply set
the
DIP switch
the
above
1ON22tothan
3 UTP
4
follow
a EDID
variation
the
instructions
OUTPUT.
1
3
4
ON
For
example:
If
OUTPUT
3
is
selected
for
INPUT
1,
the
EDID
ON
1
2
3
4
ON
OUTPUT.
position
when
matrix
is powered
OFF. On powering
ON,
all
2 Connect
thethe
AVR
to your
desired
OUTPUT
port
on2the
RESETTING
TO
FACTORY
DEFAULT:
1ON
3matrix
4
1Power
Set
the
DIP3isthe
switch
to
theand
above
position
the
matrix
inby
OUTPUT
will
be
copied
to INPUT
1your
– with
this
is
achieved
3for
ON
matrix
select
INPUT
your
ON
If
EDID
copy
not
successfully
completed,
the
INPUT
Port
EDID
1
2
3
4the
ports
will
revert
to
the
above
factory
default
and
DIP
switches
(for
example,
OUTPUT
2)
ON
1
2
3
4can
If EDID
copy
is
not
successfully
completed,
the
INPUT
Port
EDID
ON
OFF
position.
ON tothan
the
system
setting
HDMI
OUTPUT
as
a(for
higher
priority
UTP
To
reset
EDID
for
all
simply set
DIP
switch
the above
will
remain
the
unchanged.
chosen
SOURCE
isports,
connected
tothe
example,
INPUT
be
adjusted
as
necessary.
ON
ON
11
33 44
ON22chosen
will
remainON
thethe
unchanged.
3 Power
matrix
and
select your
INPUT
your
position
when
matrix
is powered
OFF.
On powering
ON,
all
ON
1ON
2 the
3matrix
4
3OUTPUT.
Blu-ray)
2–Connect
thethe
AVR
to your
desired
OUTPUT
port
on
ON
1
2
1
2
3
RESETTING
TO
FACTORY
DEFAULT:
1
2
333 4444can
AVR
7.1
Audio
EDID
COPY
toexample,
Blu-ray
source
Receiver
SOURCE
isTO
connected
to factory
(for
INPUT
3(AV
–
Blu-ray)
ON
ON
1
2
ports
will
revert
to
the
above
default
and
DIP
switches
RESETTING
FACTORY
DEFAULT:
ON
(for example,
OUTPUT
2)
Ifcopy)
EDID
copy is not
successfully
completed, the INPUT
EDID
1ON22to Port
1for
333 above
444for
be
adjusted
as
necessary.
To
reset
EDID
for
all ports,
simply
set thebutton
DIP switch
the
1ON
4
Press
and
hold
the
OUTPUT
SELECT
322
seconds
will
remain
thehold
unchanged.
ON
1
3
4
To
reset
EDID
for
all
ports,
simply
set
the
DIP
switch
to
the
above
4
Press
and
the
OUTPUT
SELECT
button
for
3
ON
3 Powerwhen
ON the
matrix
and
select your
INPUT
ON
1ON
2chosen
3 4all
4
1your
22
33
position
the
matrix
is powered
OFF.
On
powering
ON,
1
4
For
users
who
wish
to
EDID
from
anOn
AV
Receiver
with
7.1
the
EDID
data
to
becopy
copied
from
OUTPUT
2
to
1(AVR)
22OUTPUT
33INPUT
44 23
AVR
7.1
Audio
EDID
COPY
to
Blu-ray
source
(AV
Receiver
position
when
the
matrix
isdata
powered
powering
ON,
all
1ON
seconds
foristhe
EDID
toexample,
beOFF.
copied
from
ON
DEFAULT
ON
SOURCE
connected
to
(for
INPUT
3
–
Blu-ray)
RESETTING
TO
FACTORY
DEFAULT:
ON
1
2
3
4can
ports
will
revert
to
the
above
factory
default
and
DIP
switches
channel
audio
to
specific
input
portdefault
containing
aON
Blu-ray
(Blu-ray).
2 333player,
copy)
22switches
444can
ports
will
revert
toa3
the
above
factory
and 1DIP
ON
ON
11
ON
(AVR)
to
INPUT
(Blu-ray).
ON
be
adjusted
as
necessary.
follow
variation
on
instructions
ON32toseconds
1ON
3 above
4 for
4 Press
andashold
the
OUTPUT
SELECT
for
To
reseta EDID
for
all the
ports,
simply
setabove:
the button
DIP switch
the
be
adjusted
necessary.
ON
11ON
22 with
33 47.1
ON
Forthe
users
who
wish
to
copy
EDID
from
an AV 2
Receiver
44 3
ON
OFF
EDID
data
to
be
copied
from
OUTPUT
(AVR)
to
INPUT
1
2
3
position
when
the
matrix
is
powered
OFF.
On
powering
ON,
all
1
2
3
4
AVR
7.1
Audio
EDID
COPY
to DEFAULT
Blu-ray
source
(AV
Receiver
1
SetON
theaudio
DIP switch
toCOPY
the input
above
position
with
in4the
ON
ON1the
ON
2matrix
34 player,
channel
to4EDID
a /specific
containing
aON
Blu-ray
AVR
Audio
to
Blu-ray
(AV
Receiver
1080p
Video
/Stereo
Stereo
Audio
(using
1080p
3D
Audio
(using
1 7.1
23D
3Video
1 port
2default
3 source
4embedded
21
32
1
(Blu-ray).
1embedded
2switches
33 4
44can
ports
will
revert
to the
above factory
and
DIP
ON
1
2
copy)
ON
3
OFF
position.
follow
a variation
on the ON
instructions above:
copy)
111ON
222 333 444
M-series
M-series
EDID)
ON
be
adjustedEDID)
as necessary.
ON
ON22 with
111ON
33 7.1
444
For
users who
wish
to
copy
EDID from
an AV port
Receiver
2
thewish
AVRto
toto
your
desired
OUTPUT
on
22the
OFF
1this
2position
3333matrix
4will
1ON
4
1 Connect
Set
the who
DIP
switch
the EDID
above
position
with
the
matrix
in7.1
For
users
copy
from
an AV
Receiver
with
ON
DEFAULT
ON
Setting
the
DIP
switch
to
1
2
4the
ON
AVR
7.1
Audio
EDID
COPY
to
Blu-ray
source
(AV
Receiver
channel
audio
to
a
specific
input
port
containing
a
Blu-ray
player,
ON
ON
ON
(for
example,
OUTPUT
2)
1080p
3D
Video
/
Stereo
Audio
(using
embedded
1
2
3
4
1
2
3
4
1
2
3
4
2
3
1
4
1
2
3
4
ON
OFF position.
ON
channel
audio to a specific
input
port
containing
Blu-ray
player,
Setting
the
DIP
switch
this
instruct
the
matrix
to use embedded
1080p
ON
11a1to
222 33position
444
copy)
ON
follow
a variation
on the
instructions
above:
ON
3
M-series
EDID)
follow
a variation
on
the
instructions
above:
ON
ON
will
instruct
the
matrix
use
1to
22
3 4EDID
3
ON
the
matrix
and
selectDEFAULT
your
INPUT
your
chosen
compatible
video
and
Stereo
audio
ON
ON
2 Power
Connect
the
AVR
to3D
your
desired
OUTPUT
port
on
OFF
1the
2
333matrix
444the
11ON
2the
For
users
wish
toto
copy
EDID
from
an INPUT
AV
Receiver
with
7.1
1 Set
the who
DIPis switch
the
above
position
with
matrix
inwill
ON
DEFAULT
ON
ON
SOURCE
connected
to
(for
example,
3
–
Blu-ray)
to
encourage
communication
between
1
2
3
4
Setting
the
DIP
switch
to
this
position
embedded
1080p
3D
compatible
(for
example,
OUTPUT
2)
ON
1 Set
the
DIP
switch
to
the
above
position
with
the
matrix
in
the
ON
1ON2position.
3 to4a specific input
1port2 containing
3 4 21a1ON
321
433player,
4
ON
channel
Blu-ray
ON
OFF
1 position.
2audio
3 4
1theand
2matrix
3 to
4audio
11ON
222displays
33 1080p
444if
the
matrix
3D
sources/3D
instruct
use embedded
ON
video
and
Stereo
EDID
to
OFF
1
2
3
4
ON
4 Power
Press
and
thethe
OUTPUT
SELECT
button your
for
3
seconds
for
OFF
follow
a variation
on
instructions
above:
3
ON hold
the matrix
and
select
your
INPUT
chosen
11ON
22 audio
33 44EDID
ON
handshake
problems
are
encountered.
compatible
video the
and
Stereo
ON
DEFAULT
ON
2 Connect
the
AVR
to3D
your
desired
OUTPUT
port
on
the
matrix
encourage
communication
between
matrix
and
ON
1
2
3
4
OFF
the
EDID
data
to
be
copied
from
OUTPUT
2
(AVR)
to
INPUT
3
1
2
3
4
1
2
3
4
1
2
3
4
2
3
1
4
SOURCE
is
connected
to
(for
example,
INPUT
3
–
Blu-ray)
2 Connect
the AVR toto
your
desired
OUTPUT
port
onbetween
ON
ON
DEFAULT
ON
1ON
2the 3matrix
4
encourage
communication
1 Set
the
to
the
above
matrix
ON
ON
(for
example,
2)setting
ON
(Blu-ray).
1sources/3D
2 DIP
3 switch
4OUTPUT
1 position
2 DIP
3 with
4 the
21ON
321 are
43 in the
After
the
switch,
reconnect
3D
displays
if handshake
problems
4and
(for
example,
OUTPUT
2)
1 position.
2and3hold4 the OUTPUT
1 SELECT
2 3D
3 sources/3D
4
1for
333 444iffor
theON
matrix
and
ON
11take
4 OFF
Press
button
3222displays
seconds
ON
turn
onselect
for the
changes
toyour
effect.
encountered.
1
3 4
OFF
ON2
3 Power ON the matrix
and
your
INPUT
chosen
ON
1
2
4
handshake
problems
are
encountered.
the
EDID
to be copied
fromyour
OUTPUT
to333INPUT
3 Power
ON data
the matrix
and
select
INPUT2your
chosen
1(AVR)
2
44 3
OFF
ON
ON
1ON
2
2 Connect
OUTPUT
port
on
the
DEFAULT
1ON
2 the
3is AVR
4 to your
1 example,
2 3 INPUT
4ON
2
3
1
4matrix
SOURCE
connected
todesired
(for
3
–
Blu-ray)
ON
1
2
3
4
(Blu-ray).
SOURCE
is connected
to (for
example,
3reconnect
–31
ON
2Blu-ray)
1080p
Stereo
Audio
11ON
223D 3Video
4OUTPUT
2(using
3 INPUT
4embedded
211ON
433 44and
ON
After
(for
example,
2)setting
ON
3 the
4 /DIP
1 1 reconnect
2the
3DIP
4switch,
2seconds
After
setting
switch,
and
turn
on
ON
1
2
3 for
4 for
ON
4
Press
and
hold
the
OUTPUT
SELECT
button
for
3
M-series
EDID)
Stereo
(using
embedded
A-series
turn
on for
the changes
effect.
11take
33 44for
ON
41080p
Press
and
hold
the
OUTPUT
SELECT
buttontoEDID)
for
322seconds
ON
the
changes
to
take
effect.
3 Power
ON
the
matrix
and
select
your
INPUT
your
chosen
OFF
the
EDID
data
to
be
copied
from
OUTPUT
2
(AVR)
to
INPUT
ON
1
2
3
4 3
1
2
3
4
ON
ONwill
ON
ON
DEFAULT
ON
the
EDID
to beSetting
copied
2 this
(AVR)
to 3
INPUT
4 3
the
DIP
switch
to
The
matrix
use
video
3data
1from
2 OUTPUT
3 3embedded
4INPUT
SOURCE
is connected
to
(for
example,
3 position
–
Blu-ray)
ON
1080p
Audio
embedded
ON
11ON
223D 3Video
44 / Stereo
1 DEFAULT
2(using
4ON
211ON
321080p
1
43 will
ON
(Blu-ray).
ON
ON
2
4
(Blu-ray).
ON
1 2 EDID)
3 4 instruct
1the audio
2 3EDID
matrix
to4useinembedded
11ON
22 3setting.
44
and
stereo
this
DIP
3 1080p
M-series
ON
ON
1080p
Stereo
(using
embedded
A-series
EDID)
embedded
A-series
EDID)
1
3
4
41080p
Press Stereo
and hold(using
the 3D
OUTPUT
SELECT
button
for
1ON32
2seconds
3 EDID
4 for
compatible
video
and
audio
ON
DEFAULT
ONStereo
11ON
22 to
33INPUT
44and3
OFF
ON
ONDIP
After
setting
the
DIP switch,
reconnect
ON
DEFAULT
ON
the
EDID data to beSetting
copied
from
OUTPUT
2
(AVR)
the
switch
to
this
position
will
OFF
ON
231080p
343 video
44
to
encourage
between
The
matrix
use
ON
DEFAULT
ON12
3 44 / Stereo
1for
2 communication
3settings
4 4embedded
ON
ON223D 3Video
1080p
Audio
ON
1ON
2 effect.
11ON
1 will
2(using
3toembedded
1
ON
turn
on
EDID
take
(Blu-ray).
The
matrix
use
embedded
1080p
instruct
matrix
embedded
1080p
ON
2 3Video
3 444 / Stereo
1080p
Audio
(using
1the
22will
33EDID
4use
111 223D
1and
4embedded
2to
3DIP
12
4setting.
1
2
3
4if
3
1
2
3
4
ON
the
matrix
3D
sources/3D
displays
and
stereo
audio
in
this
1
3
4
ON
M-series EDID)
OFF
1
2
3
4
ON
3D
compatible
video
and
Stereo
audio
EDID
M-series
ON EDID)
DEFAULT
ON
video
and
stereo
audio
EDID
in
this
1
2
3
4
handshake
problems are encountered.
OFF
121 reconnect
2321 343 will
44and
ON2 3 4
ON
After
setting
the
DIP switch,
DEFAULT
ONthis
OFF
11ON
1 DIP
2 switch
to
encourage
between
Setting
the
to
position
ONsetting.
DIP
2 33 44 Setting
1
2 communication
33
44
ON
ON
ON
ON
DEFAULT
ON
1
2
1
2
3
4
2
3
1
4
ON
ON
the
DIP
switch
to
this
position
will
ON
1
2
3
4if
1080i
Stereo
(using
embedded
L-series
EDID)
ON
After
setting
the
DIP
switch,
reconnect
turn
onAudio
for
EDID
take
effect.
ON
1080p
11the
2matrix
33settings
44use
11ON223D 3Video
1and
3to
4embedded
2to
321
433 1080p
the
matrix
3D
sources/3D
instruct
embedded
ON
3 44 / Stereo
11ON
44and
2 2(using
2displays
instruct
the
matrix
to usetoembedded
1080p
ON
OFF
turn
on
for
the
changes
take
effect.
1
2
3
4
M-series
EDID)
handshake
problems
are
encountered.
3D
compatible
videoa and
Stereo display
audio EDID
ON
DEFAULT
ON
In OFF
instances
where
connected
12 turn
231audio
34 for
4is
After
setting
switch,
reconnect
and
on
3D
compatible
Stereo
EDID
ON
1ON
2 3 the
4 DIP
1 DEFAULT
2video
3 and
4ON
ON
ON
ON
OFF
to
encourage
communication
between
ON
unable
to
achieve
1080p
resolution
(such
ON
ON
DEFAULT
ON
1
2
3
4
1
2
3
4
Setting
the
DIP
switch
to
this
position
will
ON
1
2
3
4
1
2
3
4
2
3
1
4
ON
After
setting
the
DIP
switch,
reconnect
and
to encourage
between
EDID
effect.
ON
1080i
embedded
L-series
2 333 44(using
4to take
11ON
22communication
333
444 EDID)
111ONsettings
22Stereo
1older
2 3D
2models),
423
1ON3112
2ON
3this
4if 4
the
matrix
and
sources/3D
displays
34
1ON2
2 3
3 4
4
1ON2
2 3
3 4
4
as
using
or
cheaper
1
instruct
the
matrix
to
use
embedded
1080p
ON
1
2
3
4
1
2
3
4
1
1
turn
on
for
the
changes
to
take
effect.
theOFF
matrix and 3D
sources/3D
displays
if
1080p Stereo (using
embedded
A-series
EDID)
1
2
3
4
1
2
3
4
1
2
3
4
handshake
problems
are
encountered.
OFF
DIP
setting
will
instruct
the
matrix
to useis
In
instances
where
connected
display
3D
compatible
and
Stereo
ON
DEFAULT
encountered.
ON2 3 4 handshake
1ON
1problems
2video
3 aare
4ON
2 31audio
4 EDID
ON
OFF
111ON
222 333 444 to
1
2
3
4
2
3
1
4
The
matrix
will
use
embedded
1080p
video
1
2
3
4
embedded
1080i
video
and
stereo
audio
ON
ON
unable
to
achieve
1080p
resolution
(such
1
2
3
4
encourage
communication
between
ON
ON
ON
After
setting
the
DIP
switch,
reconnect
and
ONsetting
11ON
22the
44switch,
11ON22 33 44 After
1 audio
2 3aDIP
3signal.
4in 2this
3
1 24setting.
reconnect
3EDID
1
3and
and
stereo
DIP
EDID
to
output
as
using
older
or
cheaper
models),
this
1 2Stereo
3 4(using
1
2
3
4
the
matrix
and
3D
sources/3D
displays
if 4
1080p
embedded
A-series
EDID)
turn on for the changes to 1take2effect.
3
4
1 2 3 4
1 2 3 4
OFF
turn
on
for
the
changes
to
take
effect.
DIP setting
will instruct
the
matrix
to use
handshake
problems
are
encountered.
ON
ON
ON
ON
ON
After
setting
the
DIP
switch,
reconnect
and
After
setting
the
DIP
switch,
reconnect
and
matrix
embedded
video
11ON
22 2use
33 3video
44 4 and
11ON
1 will
2 stereo
31080p
1ON4audio
ON
ON
embedded
1080i
ON22 33 44 The
ON
turn
on
for
EDID
settings
to
effect.
ON
turnstereo
on
for
EDID
settings
to take
take
effect.
11ON22 33 44 After
1
2
4
setting
the 3
DIP
switch,
reconnect
and
audio
EDID
in
this
DIP
setting.
1
2
3
4
1
2
3and4 US: +866 677 0053 EU: +44 (0) 1793 230 343
1
2
3
4
EDID
to
signal.
1 2Stereo
3 Technical
4(using
1 output
2 A-series
3asupport@wyrestorm.com
4
Support:
1080p
embedded
EDID)
turn
on for the changes
toEDID)
take effect.
1080p
Stereo
(using
embedded
A-series
ON
ON
After
setting
the DIP
switch, reconnect
and
ON
ON
ON video
Aftermatrix
setting
reconnect
The
will
use
embedded
11ON
1for
22the
33DIP
44switch,
ON222 333 444 The
1ON
11080p
2 video
3and4
ON
turn
on
EDID
settings
to
take
effect.
ON
ON
matrix
will
use
embedded
1080p
1
1
2
3
4
1080i
embedded
1ONStereo
2 3 (using
4
ONaudio
2 L-series
3 settings
4 EDID)
turn
on 11
EDID
to take
and
stereo
1DIPeffect.
2setting.
3 4 US: +866 677 0053 EU: +44 (0) 1793 230 343
11 22 33 44 Technical
1for
22 33EDID
44 in this
Support:
21
TROUBLESHOOTING
12.
Troubleshooting
Generally, the majority of HD distribution installation
issues are either caused by minor connection
errors, communication problems between devices,
or when the transmission of high signal bandwidth
is attempted using insufficient cable. Should you
encounter any technical difficulties when installing
and configuring the matrix, we are confident
solutions can be found by working through the
following troubleshooting checklist before seeking
alternative technical support.
No Picture or poor quality picture
1) Power – are your HDBT transmitter or display receiver
baluns powered both ends? Transmitters and receivers
should have their own power source i.e. the 5v power
adaptors included with your baluns.
Note: Receivers do not need to be independently
powered if part of an HDBT extender set – there is a two
core power link between transmitter and receiver that
powers the receiver at the display end.
Are all sources definitely powered and firmly connected?
2) If possible, always use test equipment prior to
installation and to troubleshoot any problems.
3) Distance – Is your cable too long for the signal to be
transmitted effectively? HDBT Lite allows transmission of
1080p up to 70m (229ft) so make sure you cable
distance matches your requirements and is well within the
maximum transmission distance of the signal.
Note: If you are approaching the limits of the transmission
capabilities, you will need to use a Wyrestorm Extender
set for the signal to transmit effectively.
4) Cable joins? Joins in your cable run can impact on
signal strength, resulting in reduced transmission that
may manifest itself in poor picture quality or a complete
lack of picture
.
5) Signal Reduction – Are you using stranded patch
leads as interconnects between patch panels or
wall outlets? Such use reduces signal strength – we
recommend solid core straight through connections to be
used wherever possible.
6) Resolution – If you reduce the resolution of the
source, do you get a picture? If so, this suggests a
discrepancy between source and display resolution or
a bandwidth capacity issue with your cable. Check that
your inputs and outputs share the same resolution and
that the signal is being successfully transmitted along
your cable run.
7) Correct connection – It may seem obvious but
double check all UTP, HDMI, power and IR cables are
connected to the correct ports.
Note: Even a fraction off can be the difference between
a perfect picture and a blank screen. Double check all
connections are firmly made in the correct ports.
9) Cable wired to 568B standard? Is your cable wired
and terminated correctly and are those terminations
connected to the correct ports?
Test Monitor
Part Number
TTMONITOR
10) Electrical interference – HDBT is less susceptible
to interference compared to regular transmissions but
the location of cables and devices should be considered
- could any form of interference be generated? If so,
attempt to remove the source of electrical interference
or move the cable run to decrease the effects of the
interference.
11) Do you get a picture if you connect the source
directly to the display? If not then the problem could lie
with the input or output device rather than the means of
distribution i.e. the cable or matrix itself.
Signal Generator
Part Number
22
TTSIgnal
12) HDMI lead condition and quality – HDMI cables
and connectors are delicate and can be damaged much
13) Picture snow/HD ‘noise’ – represents a poorly
established signal that may be caused by poor quality
terminations or excessive cable lengths. Try swapping the
display adaptors from a location you know is functioning
properly or swapping the outputs of the matrix switch
used.
If the problem remains on the same screen this may be
caused by a connection problem between matrix and
display – turn off all equipment and swap the signal
carrying cables at both ends to ascertain if the cable or
termination is at fault.
14) Blu-ray: Deep Colour – make sure Deep Colour is
turned on in your Blu-ray settings and displays.
15) Blu-ray: Resolution – if a reduction of resolution to
720/1080i produces an image, cable issues such as
interference, patch panels, wall outlets, stranded cable
use or excessive cable length are likely restricting
transmission of a full 1080p signal.
16) Blu-ray: 3D – is the equipment used 3D enabled/
compatible? Is a 3D disc being played in a 3D enabled
Bluray player or through a compatible amplifier?
17) Colour distortion – a pink or green screen indicates
an incompatibility between colour spacing formats – the
commonly used RGB or YUV used by older displays.
Some sources allow switching between RGB and YUV
which may solve any colour problems. If not, try changing
the HDMI cable between the source and the matrix to rule
out defective cabling.
selections assigned to specific zones in the set up so
check the speakers used are fully connected to the
amplifier and correctly assigned within the system set up.
Note: If you experience problems when an AV receiver is
used, the cause is usually the settings of the AVR itself.
Refer to the AVR manufacturer’s guidelines on the correct
settings to use for your requirements.
2) Consistency of audio output between devices – Is
there any discrepancy between the audio output of the
source, the audio or zonal settings of the AV receiver and
the speaker configuration used needed for successful
audio replication? If you are outputting 7.1, make sure all
devices connected are also outputting 7.1
Note: Occasionally with some sources, the device
settings allow the specification of audio output through
a TV or an HDMI port. If using an AV receiver, check the
HDMI output option is selected.
3) Do all the local sources work through the AV
receiver?
Check the operation of each source individually.
Bandwidth
1) If using a graphics-based source (such as a PC/Mac/
media server), make sure the source resolution is set to
a maximum of 1080p, 50Hz. Higher resolutions available
for graphics-based systems require higher bandwidth
that may affect transmission of signals as well as
incompatibility with devices.
IR
1) Check you are using emitters at the IR TX
transmitter end and receivers at the IR RX receiver
end – are they connected to the correct ports on the
matrix and display receiver.
Audio is transmitted within the video signal – there
is no separate audio track – so generally a problem
with sound will be accompanied by a problem with
picture. However, if technical issues with audio are
experienced, the cause is typically communication
between sources, displays and/or AV receiver
settings.
2) Is the emitter correctly positioned on the source?
Fix the emitter directly over the infrared sensor of the
source and attach using the adhesive backing.
Note: Locate the infrared source sensor by using a
flashlight to find s small sensor within the facia of the
source display. If necessary, secure the emitter over the
sensor with a small amount of contact adhesive.
No sound or poor quality audio
3) Is your remote powered and sending a signal?
Note: IR is invisible to the naked eye, so use a digital
camera/ phone camera to check the remote signal – point
the camera at the remote control when pressing a button.
You should see the remote transmitter flashing to indicate
1) If using an AV receiver, check your source input
assignment – do you have specific speaker sets or zones
enabled? Some AV receivers allow individual speaker
23
TROUBLESHOOTING
easier than component or coax cable. Furthermore,
lead quality varies dramatically, particularly in lower price
brackets. Swap your HDMI leads and check operation –
damage to or quality of your leads could be the problem.
If in doubt, swap them over. Always take care inserting
and extracting your HDMI from matrix ports so as not to
damage the connectors or ports.
a signal being sent. Replace batteries if flashing is not
seen on the digital camera screen.
TROUBLESHOOTING AND FAQS
4) IR dropout issues can be due to exterior influences
emitting infrared radiation that can interrupt IR signals.
Ensure emitters and receivers are away from the following
causes of IR interference.
• Direct sunlight
• Halogen lighting
• Plasma screens
5) UTP Termination Issues - swap cables over at
both transmitter and receiver ends to see if control is
established. If so, a possible re-termination of the cable
could remedy the problem.
6) Are you using Wyrestorm emitters and receivers?
The use of third party products/magic eyes may not be
compatible. Always use Wyrestorm components included
with your purchase or check compatibility of third party
control systems with your Wyrestorm dealer.
7) If problems persist, swap out the IR emitters and
receivers to rule out faults with the units themselves. Use
emitters you know are fully operational to test working
condition.
8) Reactivate the IR callback function on your matrix and
swap IR ports on the matrix to rule out a fault with the
matrix or connection ports.
9) Should IR remain unresponsive, turn off and disconnect
all cables from the matrix and reconnect zones one at a
time to assess if one location in particular is the problem.
If so, run new cables directly to the display – if this fixes
the problem, it is likely that electromagnetic interference /
damage to the cable somewhere along the run is causing
the IR signal to drop out. Investigate and remove EM
interference from the run or replace damaged UTP cable.
13.
5e or 6?
FAQ’s
Although conventional transmission is considered to be
two Cat 5e cables, it is possible to send the signal down
a single cable if necessary. All of our pro-matrix switches
and UTP splitters support single UTP mode, however in
this mode IR control of sources and matrix switching is
not possible. However using HDBaseT transmission; all
of the twin cable features are supported with the added
benefit of Ethernet and RS232 control.
How far can the signal travel?
Under perfect transmission conditions our HD receivers
will operate at 30, 50 or 100m (@1080p) depending on
the model used. Perfect conditions mean no electrical
interference, straight cable runs with no bends or kinks
and no patch panels or wall outlets. If some of the
above are factors in your installation then signal strength
and bandwidth can be compromised. If a cable run is
reaching the upper limit of the receivers’ capabilities,
then the signal can be boosted by way of an extender
set (Rx TX) or by simply using an in-line repeater. Our
transmission signals can be repeated up to 5 times
(250m) using a conventional TMDS signal or 7 times
(700m) using HDBaseT technology.
What about 3D?
All of our matrix switches and most of our extender
products will pass-through a 3D Blu-ray signal. The 30m
and Coax extender sets do not support frame sequential
3D (Blu-ray), but will still pass-through interlaced stereoscopic 3D (Satellite etc.)
How do I control the sources?
Most of our HDMI distribution products support some
kind of IR pass-through from point-to-point extender sets
to pro and HDBaseT matrices. Most of the range now
supports wideband IR meaning it is compatible with any
IR device available on the market. Our Pro and HDBaseT
matrix range (Cat 5e) has IR pass-through from each of
the outputs and has discrete IR outputs at the switch
end, meaning you can have multiple identical sources yet
the IR would be routed only to the applicable source.
Do I need power at the TV end?
While our equipment is tested and graded to Cat 5e
cable standard; tests have shown that better results
are achieved when using Cat6 cable. The lower gauge,
thicker copper cores ensure better signal transfer.
Newly installed cabling should always conform to Part P
Regulation and BS 7671 (17th Edition), and should be
terminated to 568B standard
24
Can I use a single Cat 5e cable?
Yes. Our HD display adaptors require a 5v power supply
at the TV end to operate. It’s important that these are
powered locally and do not receive remote power from
the rack as there can be issues resulting from voltage
drop along the length of cable. Our new USB power
cables overcome the problem of having a second mains
outlet behind the TV. These useful leads draw the 5v from
the USB socket on the TV to power the receiver, this also
means that the receiver is only powered when the TV is
on making the system more environmentally friendly.
Using our conventional pro (TMDS) transmission method
the Video & Audio is sent along cable #2, IR and
HDCP data is sent along cable #1. Using our HDBaseT
technology it’s possible to send Audio (up to DTS Master),
Video (up to 4k), Ethernet (10/100), and control (RS232 &
2-way IR) down a single Cat 5e cable.
Are Wyrestorm products compatible with
HDMI 1.4?
HDMI 1.4 refers to a list of ‘features’ that a device is
capable of supporting, including Ethernet channel, return
audio channel, 3D etc. Due to the continuously evolving
nature of the technology, HDMI Licensing LLC have now
decided to simplify terminology by testing and referring to
cable in terms of STANDARD or HIGH-SPEED rather than
in generations 1.3, 1.4 etc.
• STANDARD (or “category 1”) HDMI cables perform
at speeds of 75Mhz or up to 6.75Gbps, which is the
equivalent to a 720p/1080i signal.
• All Wyrestorm equipment support HIGH-SPEED
(or “category 2”) HDMI cables that have been tested
to perform at speeds of 340Mhz or up to 10.2Gbps,
which is the highest bandwidth currently utilised over
an HDMI cable and can successfully handle 1080p
signals including those at increased color depths and/
or increased refresh rates from the Source. High-Speed
cables are also able to accommodate higher resolution
displays, such as WQXGA cinema monitors (resolution of
2560 x 1600).
What about screens with different
resolution capabilities?
When sending a signal point to point a TV will
communicate it’s capabilities to the source, then the
source will output a suitable signal that compatible (i.e.
1080p Stereo audio). If you were to use a matrix switch
with three 1080p screens and one 1080i screen, the
resultant image would be 1080i across all screens. The
matrix switches do not scale per output but instead
negotiate with the source a signal that all screens are
capable of supporting.
How does the Matrix cope with HDCP?
HDCP (High Definition Copyright Protection) is a feature
built in to HDMI devices to prevent theft of or illegal
distribution of HD content. Unlike competing products,
Wyrestorm matrix switches are legal and comply with
HDCP regulations. They do this by assigning a “key” to
every display connected to the switch. HDCP “keys” are
assigned to a display when connected to a HDMI device
normally. This doesn’t change when connected to a
switch; it just assigns more of them.
I can get 1080i but not 1080p at a TV
location
Firstly ensure that both the source is outputting 1080p
and that the TV is Full HD 1080p screen. If this is the case
then the receiver Cat 5e or Coax may need setting up
for long cable mode using the DIP switches. This useful
feature uses an alternative Equalisation method to re-sync
the signal over longer distances.
I cannot get a signal out from my A/V receiver along
a Cat 5e extender set
Check to ensure that the A/V Receiver isn’t adding CEC
(HDMI Control Protocol) to the outgoing signal, this can
sometimes have an effect on the HDMI signal.
14.
Maintenance
Clean this unit with a soft, dry cloth only. Never use
alcohol, paint thinner or other harsh chemicals.
15.
Product Service
Provided Service:
1. Damage requiring service: This unit should be
serviced by a qualified service personnel if:
• The DC power supply or AC adaptor has been
damaged.
• Objects or liquid have gotten into the unit.
• The unit has been exposed to rain.
• The unit does not operate normally or exhibits a marked
change in performance.
• The unit has been dropped or the cabinet damaged.
2. Servicing Personnel: Do not attempt to service
the unit beyond that described in these operating
instructions. Refer all other servicing to authorised
servicing personnel.
3. Replacement Parts: When parts need replacing,
ensure parts approved by the manufacturer are used
– either those specified by the manufacturer or parts
possessing the same characteristics as the original parts.
Be aware – unauthorised substitutes may result in fire,
electric shock, or other hazards and will invalidate your
warranty.
4. Safety Check: After repairs or service, ask the service
personnel to perform safety checks to confirm the unit is
in proper working condition.
25
FAQS , MAINTENANCE AND PRODUCT SERVICE
Do I need to use 1 or 2 cables?
MAIL-IN-SERVICE AND WARRANTY
16.
Mail-in-service
When shipping the unit, carefully pack and send it
prepaid, with adequate insurance and preferably in the
original packaging. Please include a document or letter
detailing the reason for return and include a daytime
telephone number and/or email address where you can
be contacted.
If repair is required during the limited warranty period,
the purchaser will be required to provide a sales receipt
or other proof of purchase, indicating date and location
of purchase as well as the price paid for the product.
The customer will be charged for the repair of any unit
received unless such information is provided.
17.
Warranty
Should you feel your product does not function
adequately due to defects in materials or workmanship,
we (referred to as “the warrantor”) will, for the length of
the period indicated below (starting from the original date
of purchase) either:
a) Repair the product with new or refurbished parts.
or
b) Replace it with a new or refurbished product.
Limited warranty period:
All Wyrestorm products are covered by a 2 year PARTS
and LABOUR warranty. During this period there will be no
charge for unit repair, replacement of unit components or
replacement of product if necessary.
The decision to repair or replace will be made by the
warrantor. The purchaser must mail-in the product during
the warranty period. This limited warranty only covers the
product purchased as new and is extended to the original
purchaser only. It is non-transferable to subsequent
owners, even during the warranty period.
A purchase receipt or other proof of original purchase
date is required for the limited warranty service.
26
16.
Warranty Limits and
Exclusions
1. This Limited Warranty ONLY COVERS failures due
to defects in materials or workmanship and DOES
NOT COVER normal wear and tear or cosmetic
damage.
The limited warranty also DOES NOT COVER damage
that occurs in shipment or failures caused by products
not supplied by the warrantor, failures resulting from
accident, misuse, abuse, neglect, mishandling,
misapplication, alteration, incorrect installation, set-up
adjustment, implementation of/to consumer controls,
improper maintenance, power line surge, lightening
damage, modification, service by anyone other than
a manufacturer-approved service centre or factoryauthorised personnel, or damage attributable to acts of
God.
2. There are no express warranties except as listed
under “limited warranty coverage.” The warrantor
is not liable for incidental or consequential damage
resulting from the use of this product or arising out
of any breach of this warranty.
For example: damages for lost time, the cost of having a
person/persons remove or re-install previously installed
equipment, travel to and from service location, loss of or
damage to media, images, data or other recorded/stored
content. The items listed here are not exclusive, but are
for illustration only.
Parts and service not covered by this limited warranty
are not the responsibility of the warrantor and should be
considered the responsibility of the individual.
INPUT REFERENCE LOG
INPUT REFERENCE LOGS
19. Reference Logs
Wyrestorm Matrix INPUT installation reference log
INPUT
Input
number on
Matrix
Source Location
Source Details
Source resolution & audio
settings
Cable
Number
1
2
3
4
5
6
7
8
27
EU: +44 (0) 1793 230 343
27
OUTPUT REFERENCE LOG
OUTPUT REFERENCE LOGS
Wyrestorm Matrix OUPUT installation reference log
OUTPUT
Output
number on
Matrix
Output Location
Display Details
Display Resolution & Audio
Settings
Cable
Number
1
2
3
4
5
6
7
8
28
EU: +44 (0) 1793 230 343
28
NOTES
29
NOTES
30
NOTES
31
www.wyrestorm.com
WyreStorm Offices
US Office: 6991 Appling Farms Parkway, Suite 104, Memphis, TN 38133
Tel: + 901 384 3575 Fax: + 901 384 3574
Unit 22, Ergo Business Park, Swindon, Wiltshire, SN3 3JW UK
Tel: +44 (0) 1793 230 343 Fax: +44 (0) 1793 230 583
WyreStorm Technical Support
US: +86 6677 0053
UK:- +44 (0) 1793 238 338
Email: support@wyrestorm.com
We reserve the right to change specification or product dimensions at any time.
32

Data sheet_en mx0606-0808

Transcription

Similar documents

Nordost Blue Heaven HDMI - The Listening Post Christchurch

Nordost Releases first American made HDMI cable

Home Theater - Key Digital

ZIG-SW42 User Manual

Current Page

dv news october07.indd

For RS-232 Serial Control Installation

Shiny Bow

4K Digital Media Player

MX-0404-STD-RS232