10 ft x 20 ft / 3 mx 6 m STEEL FRAME CANOPY - CPNA-CERT

10 ft x 20 ft / 3 m x 6 m
STEEL FRAME CANOPY
Instruction Manual
ITM./ART.496840
Before assembly, read these instructions carefully.
Assemble the canopy in the location where you intend to use it.
2 or more people are recommended for assembly.
WARNING: Keep all flame and heat sources away from this canopy fabric.
This canopy is made with fabric that meets CPAI-84 specifications for flame resistance.
It is not fire proof. The fabric will burn if left in continuous contact with a flame source.
This canopy is meant for vehicle/boat storage and should not be used for public
gatherings.
Please check with your local regulations prior to purchasing this item. Some
municipalities have restrictions and requirements.
This canopy should not be used during heavy wind, ice or snowing conditions. The
accumulation of snow and ice on canopy roof may pose a safety concern. Under severe
weather conditions, disassemble your canopy and store indoors.
It is strongly recommended that the canopy remain secure to the ground at all times via
the base plates and nylon straps supplied. Avoid placing the unit on soft ground and
ground that is prone to flooding.
MADE IN CHINA
For parts or customer service, please call 1-800-867-9018
Monday-Friday, 8:30am-4:30pm Pacific Standard Time
1
PARTS LIST
PART ID
DESCRIPTION
ILLUSTRATION
QUANTITY
A*
Incline Bar - 62” length
8
B
Horizontal Bar - 75 5/8” length
9
C
Post - 76” length
6
C1
Post - 76” length
2
D
3-way corner
6
E
4-way corner
6
F
Awning Arm
2
G
Awning Front Girder
1
H
Bolt (M6x16mm)
4
I
Bolt (M6x30mm)
2
J
Ring pin w/hair spring cotter
2
K
Base plate
8
L
Bolt & Nut
8
M
Canopy Roof
1
N
Side Panel with Awning
1
O
Side Panel
1
P
End Panel
1
Q
End Panel
1
R
Elastic ball strap
50
S
Ground stake
12
T
Nylon strap
4
U
Allen wrench - 5/32”
1
V
Expansion bolt
8
*NOTE: Incline bars A are packed inside posts C and C1
2
ROOF FRAME ASSEMBLY
Each bar (A, B) has a spring activated button for locking into the corner pieces.
Insert bars into corner pieces (D, E) as shown in the diagram below.
ABDE-
Incline Bar
Horizontal Bar
3-Way Corner
4-Way Corner
POST ASSEMBLY – Part 1
Insert posts (C, C1) into the corners on one side of the assembled roof as shown in the
diagram. Make sure side posts (C1) are placed as shown in the diagram. This is critical
when assembling the awning on page 7.
3
CANOPY ROOF ASSEMBLY
Spread canopy roof (M) over assembled roof frame.
If you want to attach the end panels (P & Q) then you should do so at this point. See
“SIDE AND END PANEL ASSEMBLY” on page 5.
POST ASSEMBLY – Part 2
Insert the remaining posts (C) into the corners on the other side of the roof as shown in
the diagram.
There are hooks attached to the four corners of the canopy roof (M). Insert these hooks
into the pre-drilled holes on the four corner posts (C). See diagram below.
4
BASE PLATE ASSEMBLY
Insert base plates (K) onto the bottom of the posts (C, C1) and secure using the nuts
and bolts (L).
SIDE AND END PANEL ASSEMBLY
Attach the side panel with awning (N) to the steel frame using the elastic ball straps (R).
Attention: side panel with awning (N) must be attached to the side with posts (C1).
Insert the elastic strap through the grommet in the roof (M), then behind the frame,
through the grommet in the side panel (N) and then stretch the elastic band over the
ball. See diagram below. Repeat above assembly for the remaining side panel (O) and
end panels (P & Q).
5
FINAL ASSEMBLY
1. Remove hooks from the corner posts.
2. Secure adjacent panels with hook and loop
fasteners on edge of each panel.
3. Secure panels to the posts with the 3 hook
and loop fasteners attached to the side panels.
4. Insert the hooks into the pre-drilled holes at
the bottom of each post (C, C1).
5. Insert the elastic ball strap (R) through the grommet in the end panel, through the grommets in the roof
canopy corner, then through the side panel grommet. Stretch the elastic band over the ball.
6
INSTRUCTIONS FOR ANCHORING CANOPY TO THE GROUND
Listed below are 2 options for attaching this canopy to the ground
Option 2: Canopy must be installed on a firm level surface,
regardless of surface type. To ensure safe use of this canopy, install
foot plates permanently into poured concrete blocks or railroad ties
or similar using suitable bolts.
Option 1: Assemble on grass or dirt. Secure the
canopy to the ground by inserting 8 ground stakes (S)
through each base plate (K).
Then tie the nylon strap (T) to each corner of the
canopy roof (M) and secure the 4 remaining ground
stakes (S).
Instructions for Installation into Concrete:
Note: Expansion bolts for installation into concrete are included.
1. Canopy must be installed on a firm, level surface.
2. Concrete should be at least 4 in / 10 cm thick and properly cured.
3. Assemble the canopy per the enclosed instructions. Using a
marking pen, mark the location of the holes for the 8 foot plates
where you want the canopy installed.
4. Once the locations of the holes are marked, move the foot plates
aside. Using a ¼ inch concrete drill bit, drill pilot holes for one foot
plate. Once pilot holes are drilled, use a ½ inch concrete drill bit
and drill to a depth that is the same length as the expansion bolt.
Make sure the threaded bolt sticks out of the concrete.
5. Place the expansion bolts into the holes that were just drilled.
6. Reinstall the foot plates on each post and place foot plate over the
expansion bolt.
7. Recheck the locations of the holes previously marked for the
remaining foot plates to ensure all holes are in alignment.
8. Install washers, lock washers and nuts.
9. Do not fully tighten each bolt on each plate. Alternate gradual
tightening of all bolts on the plates until all plates are fully secured.
AWNING ASSEMBLY
Attach awning arms (F) to the posts (C1) using bolts (H). See diagram below.
Connect fabric fasteners on the roof (M) with the fabric fasteners on the side panels (N & O).
7
AWNING ASSEMBLY
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
Step 7
Step 8
8