instruction 2005 page 01.pub

All of these configurations are from one 2005 Blue Ultralite Trayman.
Just slide the straps up and over your shoulders
and they will slip into place.
The back edge of the Shoulder Strap has a slight bend outward
That allows the “Trayman” to slide easily on and off.
To Remove the “Trayman” simply tilt the unit off from your midriff
with one easy motion.
The Right Strap ,as you wear the Trayman, has the longer
Safety Stop
The Right Chest bar is the thicker of the two Chest Bars at it’s end. Insert the
Right Strap into the Right Chest Bar. Next slip on one nylon washer and then
tighten the “Quick Grip” knob that was originally on the Strap when you opened
up the Strap’s Shipping Bag. After slipping the Trayman onto your shoulders hand
tighten the knobs for both the right and left straps.
Repeat the same insert and tightening of the second Quick Grip Knob to
the Left Shoulder Strap and Left Cross Bar. Remember the Left Cross Bar
is thinner at it’s end then the Right Cross Bar is.
The Shoulder Strap Stops allow the Straps to extend from 90 to 45 degrees safely.
This will allow you to adjust the Strap to the best angle for your shoulders.
The Shoulder Straps are attached using hardened steel 10/32 Button Head Allen
Bolts that are secured with Red Lock-Tite. The relief pattern will allow the Straps
to be bent one time to shorten the strap for some women. You may wish to bend
the arc of the strap slightly as well to fit yourself. First remove the Straps
and adjust them a little bit at a time. Your Trayman is made from
6061 Aircraft Quality Aluminum which is very strong ,
however multiple adjustments of the Straps Arc is not recommended
The Center Wave Grip is a combination of a Sure Grip Knob and 10/32 hardened
steel Thread, one Nylon Washer, and The Center Wave Grip itself. This allows the
Left and Right Upper Chest Bars to be quickly opened and closed as desired,
and allow for a wide range of chest and shoulder sizes.
The Wave Grips are cut from Billet 6061 Aluminum stock.
The Center Wave grip being adjusted from it's narrowest to widest positions.
The use of the Lower Wave Grip is similar to the Center Wave Grip
in all it’s operation and adjustments.
This is one of the reasons no accessories are needed,
even if you are a very tall person, or a individual with a very long reach.
The “Trayman” has a incredible range of adjustability crafted into it’s design.
The Upper Spine is totally removable allowing the overall length to be even
shorter then the Lower Wave Grip allows for. Simply remove the Upper Spine Bar
and attach the Upper Wave Grip and Chest Bars to The Lower Spine Bar. It will
help if you keep the unneeded parts assembled as shown for use later on.
Machined out of 6061 Billet Aluminum the Fast Lock Tray Swivel will lock down
with a sure grip supported by it’s hardened steel pivot shaft also secured,
as are all hard points, with Red Lock-Tite.
The CNC Machined Timed Wave Pattern allows you to find just the right angle of
tilt for the trays. Your individual “sweet spot” will be exactly where you are most
comfortable. The Sure Grip brass lined knob only needs to be twisted open to adjust the angle of the Trayman Tables. A Nylon release washer guards against over
tightening the mechanism via a strong pair of hands or too much enthusiasm.
The two Tray Support Spines are made so that each Tray may touch
or slide away from each other. This side to side travel extends as far as
the end of each slot that has been milled into the Lower Cross Bar.
The two Tray Spines allow the Trays to slide away from or towards the user.
The Trayman Tables have been rotated up vertically and locked into place so that
you can clearly see the underside of the Tables. This exposes the two Tray Spines
and the four smaller Quick Grip Knobs that both secure the Trays and allow them
to be repositioned. Just loosen each pair of Knobs and slide the Tray into whatever position best fits your transmitter. Please note that the Trayman Tables maybe
rotated into any position or relationship to one another.
There is a great number of Tray combinations that are possible.
The Bungee Cord in the center has been attached in a typical four “Bungee-Bud”
pattern and is now ready to be slipped over any transmitter’s handle. This is one
of Trayman’s Patent Pending two part lock down system.
This is the Two Part Bungee-Bud Lock Down System. The First part is our rectangular Velcro Block. This piece of Billet Aluminum has been hogged out to remove
any extra weight and is bolted to the Lower Cross Bar with two Stainless Steel
Bolts that are secured with Red Lock-Tite. Rip-N-Grip self-adhesive hook material is applied to the Block. The softer loop Rip-N-Grip material is placed on the
underside of any transmitter, between the transmitter’s legs. Slip the Bungee Cord
over the trans-
These are the two Stainless Steel Bolts that secure the Velcro Block
before it is covered. The Rip-N-Grip hook material has been pre-applied.
Just peal off the matching self-sticking loop material and after removing the white
protective backing, apply it to the center of the underside of your transmitter.
Be sure to leave an equal space between each of the two feet. Press the Rip-NGrip into place firmly checking that the battery door is clear. If there is a serial
number copy it down and tape it to the inside of the battery cover with your name.
Having pressed the Hook-N-Grip into position the transmitter can
now be quickly mounted on the trays by simply lining up the two
parts of the material
Interlock the Rip-N-Grip Pads, Slip the Bungee-Bud Cord over the handle only,
line up the edge of the Tray with the handle and the transmitter is locked down.
The 2005 Ultra Lite fite all transmitters and more..
This is the Bungee-Bud and Rip-N-Grip Kit that come with each tray.
There is an extra Bungee Cord, a pair of Spare Nylon Washers,
and more self adhesive Rip-N-Grip material.
The Tilt Wrist Rest has been made to fit into any of the slots or threaded openings
in the Trayman Tray Table. The long 10/32 threaded bolt will slide along the slots
to be adjusted exactly where it will best fit the edge of your hand.
The Belt Buckle provide a pivot point and general pad for the Tray Tables to
rest upon at the users waist. The Stainless Steel bolts are set into place with
Red Lock-Tite so they will not come loose with use.
The actual use of a belt is not required,
for the general use, of our Ultra Lite 2005 Blue Trayman.
Disclaimer: Please note that none of the products shown as examples of applications for the use of our 2005 Ultra Lite Blue Trayman should suggest that the
brands we have shown endorse our Tray. We are not affiliated with any other
manufacturer of Transmitters, Video or Computer equipment. Our product fits
many other applications in Film, Sports, Theater, Inventory, Intake clipboards,
Artwork, Medical Services, and as a general personal reading or writing platform.
There are new applications found for our unit every day. As you discover your
own please let us know about them. Your comments are always welcome.
Caution: All of the fittings and hardware are of stainless steel or hardened steel
and all of the end points have been treated with Red Lock-Tite. No bolt has been
made to be removed except those that are made to be adjusted.
Caution: Do not overload your Trayman System. Be sure that all of the Quick
Grip Knobs have been hand tightened especially the Table Tilt Swivel. The Wave
Grip Teeth can only hold if they are properly engaged.
Remember: Common sense and an eye towards safety are your best protection.
Liability: Rc Trayman USA LLC assumes no liability for the use of this system or
any damages that occur from it’s being used in any application whatsoever.