LANAUGHURK Installation Instructions

Transcription

LANAUGHURK
Installation Instructions
HUR Unloading Auger Extension for John Deere® Combines
** FOR HIGH UNLOAD RATE AUGERS ONLY **
270 West Park Avenue
Huron, SD 57350
866-526-5682
Page | 1
5/15/2015 www.lankota.com | Lankota Inc.
John Deere and JD are registered trademarks of Deere & Company.
Lankota is a registered trademark of Lankota Group.
Numerical Parts List
Part Number
Description
LANAUGHUR-B
Bearing Hanger
LANAUGHUR-C
Access Cover
LANAUGHUR-F
Auger Flighting Extension Weldment
LANAUGHUR-T1
Saddle Tube
LANAUGHUR-T2
Extension Tube
LANMOU20516GSA*
Bearing w/ Lock Collar
LAN52MM3ZP*
Bearing Flange
LAN4A16A16*
5/16”-18 x 1-1/4” Carriage Bolt
LAN1616*
5/16”-18 Nylon Lock Nut
RED305K*
3/8”-16 x 1-1/4” Carriage Bolt
LAN3718*
3/8”-16 Serrated Lock Nut
LANAUG283W
Grain Saver Weldment
LANAUG295
Spring Retainer Band
LANAUG276
Spring Arm
LANH217334
Spring
LANFGCMN
Bolt Retainer
LAN18A
3/8” -16 X 1.00” Carriage Bolt
LAN161800
3/8” -16 Nylon Lock Nut
LANF011B
1/2” -13 x 2.00” Full Thread Bolt
LANF-HN-0.500C
1/2" -13 Hex Nut
*included in bag of hardware.
Page | 2
Quantity
1
1
1
1
1
1
2
3
3
13
17
1
2
2
2
9
2
2
2
2
Pictorial Parts List
LANMOU20516GSA (1)
LANAUGHUR-T1 (1)
LAN1616 (3)
LAN4A16A16 (3)
LAN52MM3ZP (2)
LANAUGHUR-F (1)
RED305K (13)
LANAUGHUR-C (1)
LANAUGHUR-B (1)
Page | 3
LANAUGHUR-T2 (1)
LAN3718 (17)
Pictorial Parts List
LANAUG283W
LANAUG295 (2)
LANAUG276 (2)
LAN18A (2)
LAN1618000 (2)
LANF011B (2)
Page | 4
LANH217344 (2)
LANFGMN (9)
LANF-HN-0.500C (2)
1. Auger Extension Kit
Refer to Figure 1.1
1.1 Remove the plastic spout and factory grain saver door from the
existing auger tube.
Figure 1.1
1.2 Retain all hardware for re-use later in the installation.
1.3 The factory bearing hanger and its hardware should remain fastened to
the existing auger tube.
Page | 5
Refer to Figure 1.2 & 1.3
1.4 Slide the auger Saddle Tube (LANAUGHUR-T1) over the
existing auger tube and temporarily secure with one
LAN3718 carriage bolt and serrated lock nut.
Figure 1.2
Note in figure 1.2 that there are slots for the existing
bearing hanger bolts to fit through on each side.
1.5 Slide the auger Extension Tube (LANAUGHUR-T2) into the
auger saddle tube and align with the access door. Install an
additional eight LAN3718 and serrated lock nuts
along the top rib of auger saddle tube. Tighten all hardware.
1.6 Install the Auger Flighting Extension Weldment
(LANAUGHUR-F) through the auger extension tube and
align with the male hex shaft on the end of the existing
auger. Use the access door on the side for assistance to lift
and align the flighting extension.
Figure 1.3
Timing auger extension: The new flighting should trail the
existing flighting by 90 – 180 degrees.
Note: See Figure 1.3 for an example of flighting trailing by 120
degrees.
Page | 6
Refer to Figure 1.4 & 1.5
1.7 Install the Bearing Hanger (LANAUGHUR-B) inside the auger
extension tube. Note the positioning of the bearing hanger as
shown in Figure 1.4. Secure bearing hanger to tube using four of the
(RED305K) Carriage Bolts & four of the (LAN3718) Lock Nuts. Tighten
all hardware. Support the end of auger flighting extension
weldment to the bearing hanger with Bearing (LANMOU20516GSA)
and Bearing Flanges (LAN52MM3ZP). Install the bearing onto the
outer side of the bearing hanger and secure with three LAN4A16A16
and LAN1616
Figure 1.4
Tighten all hardware.
Tighten both set screws on the bearing lock collar.
1.8 Install Access Cover (LANAUGHUR-C) and secure with four LAN3718 as
shown in figure 1.5.
Page | 7
Figure 1.5
2. Grain Saver Door Installation
Refer to Figure 1
1. Install the Grain Saver Weldment (LANAUG283W) onto the end of the auger tube as shown below. Re-install the two original carriage
bolts and nuts previously removed from the factory grain saver.
Figure 1
Page | 8
Refer to Figure 2
2. Slide the spout back into place. Measure out 5” and down 1.25” from circled bolt hole and dot a mark (RED LINES). Repeat on opposite
side.
3. Remove the spout and drill 5/8” hole (or slightly larger) at the marked location.
4. Using a blade or tin snips, cut from the center of the factory spout bolt hole to the 5/8” hole you just drilled (Yellow LINE).
Repeat on opposite side. This will allow the black spout to still be able to “pop” off if needed like the factory design.
5. Re-install the spout and its original hardware as removed earlier in step 1. The Bolt Retainers (LANFGCMN) have been provided to assist
with retaining the carriage bolts for ease of re-installation of the plastic spout. Tighten all hardware.
Installation tip: It may be helpful to use a deep socket (with similar diameter as the bolt retainer) in aid as an insertion tool for the retainers.
6. Install the Spring Arms (LANAUG276) and hardware onto grain saver weldment through the drilled hole in the spout. Use the hex nut as a
jam nut behind the spring arm. The bolt should be threaded all the way into the welded pivot nut of the grain saver weldment and
tightened. The spring arm should be vertically straight with the auger tube as shown with the door in the closed position.
Hardware:
(2) LANF011B 1/2”-13 x 2.00” Fully Threaded Bolt
(2) LANF-HN-0.500C 1/2”-13 Hex Nut
Figure 2
Page | 9
Refer to Figure 3
8. Position the Spring Retainer Bands (LANAUG295) around the
auger tube at a distance of 7-1/2” from the pivot point of
spring arm and secure with the hardware.
Figure 3
Hardware:
(2) LAN18A 3/8”-16 x 1.00” Carriage Bolt
(2) LAN1618000 3/8”-16 Nylon Lock Nut
9. Install the Springs (LANH217334) between the spring
retainer bands and spring arms. Adjustment may be
accomplished by sliding the spring retainer band alongside
the auger tube.
For further technical assistance call Lankota at 866-526-5682
Page | 10

LANAUGHURK Installation Instructions

Transcription

Similar documents

Setup Instructions

DEMCO GRAIN CARTS

Logging onto JDParts for the first time - Wickham

Saturday, June 2 – 10:00 AM

career - Nortrax

John Deere tractor

Demco Gravity Flow Wagons and Grain Carts

240 HOLE DIGGER

Defender 4 Seed Caddy

steel-sided auger bunk feeder

Fishing Derby Win This CheVy TrUCK!