SR15 SR10 MPB PUB 06-05 REV 04-06

Transcription

SR15/SR10
FLEX-WING
ROTARY CUTTER/SHREDDER
P/N 00764578MB
Revision 04-06
MASTER PARTS BOOK
S/N 10001 TO 11270
PARTS LISTING
Rhino®
An Alamo Group Company
1020 S. Sangamon Ave.
Gibson City, Il 60936
1-800-446-5158
Email: parts@servis-rhino.com
© 2006 Alamo Group Inc.
TO THE OWNER/OPERATOR/DEALER
All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who
recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to
be used with all its safety equipment properly attached to minimize the chance of accidents.
BEFORE YOU START!! Read the safety messages on the implement and shown in your manual.
Observe the rules of safety and common sense!
WARRANTY INFORMATION:
Read and understand the complete Warranty Statement found in this Manual. Fill out the Warranty Registration Form
in full and return it within 30 Days. Make certain the Serial Number of the Machine is recorded on the Warranty Card
and on the Warranty Form that you retain. The use of "will-fit" parts will void your warranty and can cause catastrophic
failure with possible injury or death.
PARTS
SECTION
Parts Section – 1
PARTS ORDERING GUIDE
The following instructions are offered to help eliminate needless delay and error in processing
purchase orders for the equipment in this section.
1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the
basic machine featured in this manual. Part Numbers and Descriptions are given to help
locate the parts and quantities required.
2. The Purchase Order must include the name and address of the person or organization
ordering the parts, who should be charged, and if possible, the serial number of the machine
for which the parts are ordered.
3. The Purchase Order must clearly list the quantity of each part, the complete and correct part
number (be sure to include all periods), and the basic name of the part.
4. The Manufacturer reserves the right to substitute parts where applicable.
5. Some parts are unlisted items which are special production items not normally stocked and
are subject to special handling. Request a quotation for such parts before sending a
Purchase Order.
6. The Manufacturer reserves the right to change prices without prior notice.
NOTE:
Please refer to The Safety Section in the front of this Manual for the proper
Part Number when ordering Replacement Safety Decals.
For maximum safety and to guarantee optimum product reliability, always use
genuine Servis-Rhino Parts. The use of inferior replacement parts may cause
premature or catastrophic failure which could result in serious injury or death.
Direct any questions regarding parts to:
RHINO ®
Gibson City, IL 60936
800-446-5158
©2006 Alamo Group Inc.
Parts Section – 2
PART NAME INDEX
AXLE ASSEMBLY SN 10001 - 11270 APR 1988 - SEPT 1990............................................................................................ 5
BLADE PAN ASSEMBLY - CENTER SN 10001 - 11270 APR 1988 - SEPT 1990 .............................................................. 6
BLADE PAN ASSEMBLY - WING SN 10001 - 11270 APR 1988 - SEPT 1990 ................................................................... 7
CHAIN GUARD ASSEMBLY - FRONT CENTER SECTION SN 10001 - 11270 APR 1988 - SEPT 1990........................... 8
CHAIN GUARD ASSEMBLY - FRONT WING SN 10001 - 11270 APR 1988 - SEPT 1990................................................. 9
CHAIN GUARD ASSEMBLY - REAR CENTER SECTION SN 10001 - 11270 APR 1988 - SEPT 1990 ........................... 10
CHAIN GUARD ASSEMBLY - REAR LEFT WING SN 10001 - 11270 APR 1988 - SEPT 1990 ....................................... 11
CHAIN GUARD ASSEMBLY - REAR RIGHT WING SN 10001 - 11270 APR 1988 - SEPT 1990..................................... 12
CYLINDER ASSEMBLY - CENTER SECTION LIFT SN 10001 - 11270 APR 1988 - SEPT 1990..................................... 13
CYLINDER ASSEMBLY - LEVEL LIFT CENTER SECTION 3 x 8 SLAVE SN 10001 - 10526 APR 1988 - MAR ............. 16
CYLINDER ASSEMBLY - LEVEL LIFT CENTER SECTION 3-1/2 x 8 SLAVE SN 10527 - 11270 MAR 1989 - ............... 18
CYLINDER ASSEMBLY - LEVEL LIFT LEFT WING 2-1/2 x 8 SLAVE SN 10001 - 10526 APR 1988 - MAR 1................ 14
CYLINDER ASSEMBLY - LEVEL LIFT LEFT WING 3 x 8 SLAVE SN 10527 - 11270 MAR 1989 - SEPT 1990 .............. 17
CYLINDER ASSEMBLY - LEVEL LIFT RIGHT WING 2-3/4 x 8 SLAVE SN 10001 - 10526 APR 1988 - MAR................. 15
CYLINDER ASSEMBLY - LEVEL LIFT RIGHT WING 3-1/4 x 8 SLAVE SN 10527 - 11270 MAR 1989 - SEPT............... 19
CYLINDER ASSEMBLY - WING SECTION LIFT SN 10001 - 11270 APR 1988 - SEPT 1990.......................................... 20
DEFLECTOR - REAR LEFT AND RIGHT WING SN 10001 - 11270 APR 1988 - SEPT 1990 .......................................... 21
DEFLECTOR - RUBBER CENTER SECTION REAR SN 10001 - 11270 APR 1988 - SEPT 1990 ................................... 22
DEFLECTOR - RUBBER FRONT CENTER SN 10001 - 11270 APR 1988 - SEPT 1990.................................................. 23
DEFLECTOR - RUBBER FRONT WING SN 10001 - 11270 APR 1988 - SEPT 1990....................................................... 24
DEFLECTOR - RUBBER LH RH CENTER SN 10001 - 11270 APR 1988 - SEPT 1990 ................................................... 25
DRIVELINE ASSEMBLY - CAT 4 WING SN 10001 - 11209 APR 1988 - MAR 1990......................................................... 26
DRIVELINE ASSEMBLY - CAT 5 WING SN 10980 - 11270 MAR 1990 - SEPT 1990....................................................... 29
DRIVELINE ASSEMBLY - INTERMEDIATE SN 10001 - 11270 APR 1988 - SPET 1990.................................................. 30
DRIVELINE ASSEMBLY - MAIN CV 1000 RPM SN 10001 - 11000 APR 1988 - SEPT 1990 ........................................... 32
DRIVELINE ASSEMBLY - MAIN CV 540 RPM SN 10001 - 11000 APR 1988 - APR 1990 ............................................... 35
DRIVELINE ASSEMBLY - MAIN CV 540 RPM SN 10001 - 11270 APR 1998 - SEPT 1990 ............................................. 36
DRIVELINE ASSEMBLY - MAIN CV 540 RPM SN 11001 - 11270 APR 1990 - SEPT 1990 ............................................. 37
DRIVELINE ASSEMBLY - MAIN 44R 540/1000 RPM SN 10001 - 11270 APR 1988 - 1990 ............................................. 31
GEARBOX ASSEMBLY - CENTER SECTION 1000 RPM SN 10001 - 11270 APR 1988 - SEPT 1990 ........................... 44
GEARBOX ASSEMBLY - DIVIDER 1000 RPM SN 10001 - 11100 APR 1988 - MAR 1990 .............................................. 46
GEARBOX ASSEMBLY - DIVIDER 1000 RPM SN 11101 - 11270 MAR 1990 - OCT 1990 .............................................. 48
GEARBOX ASSEMBLY - DIVIDER 540 RPM SN 10001 - 11100 APR 1988 - MAR 1990 ................................................ 50
GEARBOX ASSEMBLY - DIVIDER 540 RPM SN 11101 - 11270 MAR 1990 - OCT 1990 ................................................ 52
GEARBOX ASSEMBLY - LEFT WING 1000 RPM SN 10001 - 11270 APR 1988 - SEPT 1990........................................ 54
GEARBOX ASSEMBLY - 1000 RPM SN 10001 - 11270 APR 1988 - SEPT 1990............................................................. 38
GEARBOX ASSEMBLY - 540 RPM SN 10001 - 11270 APR 1988 - SEPT 1990......................................................... 40, 42
HOSE BRACKET ASSEMBLY SN 10001 - 11270 APR 1988 - SEPT 1990....................................................................... 56
HYDRAULIC VALVE ASSEMBLY - CLOSED CENTER SN 10001 - 11270 APR 1988 - SEPT 1990 ............................... 57
HYDRAULIC VALVE ASSEMBLY - CONVERSION PLUG SN 10001 - 11270 APR 1988 - SEPT 1990........................... 58
HYDRAULIC VALVE ASSEMBLY - DETENT W/SPRING ASSEMBLY SN 10001 - 11270 APR 1988 - SEPT 1990........ 59
HYDRAULIC VALVE ASSEMBLY - NON-ADJUSTABLE RELIEF SN 10001 - 11270 APR 1988 - SEPT 1990.......... 60, 61
HYDRAULIC VALVE ASSEMBLY - OPEN/CLOSED CENTER VALVE SN 10001 - 11270 APR 1988 - SEPT 1990 ....... 62
JACK ASSEMBLY - TOP WIND SN 10001 - 11270 APR 1988 - SEPT 1990 .................................................................... 63
LEVEL ROD ASSEMBLY SN 10001 - 11270 APR 1988 - SEPT 1990............................................................................... 64
LIFT SCREW SN 10001 - 11270 APR 1988 - SEPT 1990.................................................................................................. 65
MAINFRAME COMPONENTS S/N 10001 - 11270 APR 1988 - SEPT 1990 ...................................................................... 66
SAFETY SHIELD ASSEMBLY SN 10001 - 11100 APR 1988 - MAR 1990 ........................................................................ 67
SAFETY SHIELD ASSEMBLY SN 11101 - 11270 MAR 1990 - OCT 1990 ........................................................................ 68
SKID SHOE & SIDE SKIRT - OFFSET MODELS SN 10001 - 11270 APR 1988 - SEPT 1990......................................... 69
SKID SHOE & SIDE SKIRT ASSEMBLY SN 10001 - 11270 APR 1988 - SEPT 1990 ...................................................... 71
SKID SHOE - CENTER SECTION SN 10001 - 11270 APR 1988 - SEPT 1990 ................................................................ 70
SLIP CLUTCH ASSEMBLY - SERIES 6 SN 10001 - 11270 APR 1988 - SEPT 1990........................................................ 72
SLIP CLUTCH ASSEMBLY - SERIES 8 SN 10001 - 11270 APR 1988 - SEPT 1990........................................................ 73
SPRING POD ASSEMBLY - CENTER AXLE SN 10001 - 11270 APR 1988 - SEPT 1990................................................ 74
SPRING POD ASSEMBLY - OUTBOARD AXLE SN 10001 - 11270 APR 1988 - SEPT 1990 .......................................... 75
TIRE SN 10001 - 11270 APR 1988 - SEPT 1990 ............................................................................................................... 76
TONGUE ASSEMBLY USED ON C.V. DRIVELINE SN 10001 - 11270 APR 1988 - SEPT 1990 .................................... 78
TONGUE ASSEMBLY USED ON 44R DRIVELINE SN 10527 - 11270 MAR 1989 - SEPT 1990 ..................................... 77
SR15/SR10 Master Parts Book (Jun-05) Rev 04-06
Parts Section – 3
PART NAME INDEX
WEIGHT BOX SN 10001 - 11270 APR 1988 - SEPT 1990 ................................................................................................ 79
WHEEL HUB ASSEMBLY SN 10001 - 11270 APR 1988 - SEPT 1990 ............................................................................. 80
WINCH & HOLD DOWN STRAP SN 10001 - 11270 APR 1988 - SEPT 1990 ................................................................... 81
Parts Section – 4
AXLE ASSEMBLY SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
00756981
00756976
00756978
00756977
00756686
00756975
00756694
20BH5012
15B1600
65106A4
02782000
00037200
00756700
00756693
00756687
1
1
1
1
1
1
1
4
4
2
4
4
2
2
2
CENTER AXLE ASSY SINGLE
CENTER AXLE ASSY DUAL
RIGHT AXLE ASSY
LEFT AXLE ASSY
WLDMT, CENTER AXLE *
OUTBOARD AXLE WLDMT RIGHT
OUTBOARD AXLE WLDMT LEFT
PIN-SPIRAL 5/16 X 1 1/2 *
WASHER 1 SAE P *
WLDMT,AXLE PIVOT PIN *
SHCS 3/4 NC 3-3/4 PL8 *
NUT TOPLOCK 3/4 NC PLC *
PIN-AXLE PIVOT WLDMT
CENTER SECTION-SINGLE SPINDLE
DOUBLE SPINDLE AXLE ARM
2
3
4
5
6
7
8
9
10
11
12
13
14
*Parts included in Axle Assembly w/Hubs for Center Axle PN 00756981 or PN 00756976.
Parts Section – 5
BLADE PAN ASSEMBLY - CENTER SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
00756698
0582010330
582013
571044
0656150200
571045
5GL16140
1
2
2
4
2
2
2
WLDMT, CTR SECTION BLADE PAN
BLADE, CCW FAN
BLADE, CCW/CW FLAT
BOLT SHOULDER
ORDER 70 MIN HT WASHER
WASHER
LOCKNUT 1 -14 LH TLN PL
3
4
5
6
NOTE: Center Blades CCW Rotation
Parts Section – 6
BLADE PAN ASSEMBLY - WING SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
00756699
0652010330
0622010330
0652010030
571044
0656150200
571045
5GL16140
1
2
2
4
4
2
2
2
WLDMT, WING BLADE PAN
BLADE, CW FAN
BLADE, CCW FAN
BLADE, CCW/CW FLAT
BOLT SHOULDER
ORDER 70 MIN HT WASHER
WASHER
LOCKNUT 1 -14 LH TLN PL
3
4
5
6
Parts Section – 7
CHAIN GUARD ASSEMBLY - FRONT CENTER SECTION SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
1
2
3
1
2
3
1
2
3
PART NO.
QTY.
DESCRIPTION
00756985
02030700
00002700
00001800
-------------00756989
02030700
00002700
00001800
------------00756987
02030700
00002700
00001800
3
3
3
CENTER SECTION - FRONT
HHCS 1/2-13UNC 1-1/4 PL5
FLATWASHER 1/2 PL STD
LOCKNUT TLM 1/2 NC PLB
--------------------------------------------CENTER SECTION RH FRONT
HHCS 1/2-13UNC 1-1/4 PL5
--------------------------------------------CENTER SECTION LH FRONT
HHCS 1/2-13UNC 1-1/4 PL5
2
2
2
2
2
2
Parts Section – 8
CHAIN GUARD ASSEMBLY - FRONT WING SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
00756986
00756688
00751126
0652100202
02030700
00002700
00001800
1
64
1
7
7
7
WING CHAIN GUARD ASSY
WING CHAINGUARD BAR
CHAIN 5/16 WLD 6 LINK
ROD CHAIN
HHCS 1/2-13UNC 1-1/4 PL5
Parts Section – 9
CHAIN GUARD ASSEMBLY - REAR CENTER SECTION SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
00756988
00756892
00755090
00757142
00002500
00011100
00015800
00751126
1
54
1
8
8
8
2
CENTER SECTION-REAR CHAINGUARD
CENTER SECTION CHAINGUARD BAR
CHAIN 5/16- 5 LINKS WLD
ROD, CENTER SECT. REAR C.G.
SHCS 3/8 NC 1-1/4 PL5
NUT,TOPLOCK 3/8NC PLB
Parts Section – 10
CHAIN GUARD ASSEMBLY - REAR LEFT WING SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
12
13
0652110300
0652110310
00751126
0652110201
00013300
00002700
00001800
00756876
652053
00752680
7A81336
02030700
1
1
110
2
2
10
10
2
8
6
2
4
LEFT REAR WING CHN GD
MOUNTING BRKT, LEFT
ROD CHAIN
HEXB 1/2 NC 2 PL5
WING REAR COVER
SPACER
HHCS 1/2-13UNC X 4LG PL5
C/S1/2 X 4-1/2 NC PL5
HHCS 1/2-13UNC 1-1/4 PL5
CHAIN GUARD ASSEMBLY - REAR RIGHT WING SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
12
13
0652110200
0652110210
00751126
0652110201
00013300
00002700
00001800
00756876
652053
00752680
7A81336
02030700
1
1
110
2
2
10
10
2
8
6
2
4
RT REAR CHN GD ASSY
MOUNTING BRKT, RIGHT
ROD CHAIN
HEXB 1/2 NC 2 PL5
WING REAR COVER
SPACER
HHCS 1/2-13UNC X 4LG PL5
C/S1/2 X 4-1/2 NC PL5
HHCS 1/2-13UNC 1-1/4 PL5
CYLINDER ASSEMBLY - CENTER SECTION LIFT SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
8727
B651302
94514
7329
8755
8751
8753
8752
00013901
00023100
8754
4690W
8757
8756
4675W
8354
162012
6511324
8763
1
1
1
1
1
1
1
1
1
1
8
1
4
1
2
2
1
-
HYDRAULIC CYLINDER, T
HOSE #6 - 8MP - 8MP - 180LG
ADAPTER, HYD, ELBOW SWIVEL
ADAPTER, HYD, STGHT RESTRICTOR
CAP (HYD. CYLINDER)
PISTON
PISTON ROD
TUBE (HYD. CYLINDER)
NUT HEX 3/8 NC PL
HHCS 3/8 -16UNC 1-1/2 PL5
CLEVIS,OUTER
INSTALL SHEET-BELT TENSIONER&S
HEAD
TIE ROD
MANUAL-SR320 P/T HAY RAKE
PIN-HYD. CYLINDER
PIN,COTTER
BREATHER,1/2 SQ HD CORED
SEAL KIT
CYLINDER ASSEMBLY - LEVEL LIFT LEFT WING 2-1/2 x 8 SLAVE SN 10001 - 10526 APR 1988 - MAR 1
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
14
15
16
17
18
0652141500
0652141506
0652141502
0652141503
0652140305
0652141404
0652141501
0652140307
0652141540
691356
163016
0652141311
691302
B651302
6513015
B65113A2
94514
1
1
1
4
1
1
1
1
2
4
4
1
1
1
1
6
CLY, LEVEL LIFT
CLEVIS,BASE
BARREL
GLAND
TIEROD,HYD CYL W/NUT
PISTON
ROD
CLEVIS, ROD
SEAL KIT
PIN
PIN, COTTER 3/16 X 2
ADP HYD STGHT 8MB - 8FP
HYD HOSE-3/8-8W/(1/2FITTING
HOSE #6 - 8MP - 8MP - 180LG
HOSE #6 - 8 MP - 8 MP 216 LG
HYD HOSE ONE
CYLINDER ASSEMBLY - LEVEL LIFT RIGHT WING 2-3/4 x 8 SLAVE SN 10001 - 10526 APR 1988 - MAR
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
14
15
16
17
18
0652141400
0652141406
0652141402
0652141403
0652140305
0652141404
0652141401
0652140307
0652141440
691356
163016
0652141311
691302
B651302
6513015
B65113A2
94514
1
1
1
4
1
1
1
1
2
4
2
1
1
1
1
6
HYD CYL KIT
CLEVIS,BASE
TUBE HYD CYL
GLAND,ROD END
PISTON
ROD,PISTON
CLEVIS, ROD
SEAL KIT
PIN
ADP HYD STGHT 8MB - 8FP
HOSE #6 - 8MP - 8MP - 180LG
HOSE #6 - 8 MP - 8 MP 216 LG
HYD HOSE ONE
CYLINDER ASSEMBLY - LEVEL LIFT CENTER SECTION 3 x 8 SLAVE SN 10001 - 10526 APR 1988 - MAR
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
13
14
15
16
17
18
0652141300
0652141306
0652141302
0652141303
0652140305
0652141304
0652141301
0652140307
0652141340
691356
163016
0652140320
691302
B651302
6513015
B65113A2
94514
1
1
1
4
1
1
1
1
2
4
1
1
1
1
1
6
HYD CYL KIT
BUTT
BARREL
GLAND
PISTON
ROD
CLEVIS, ROD
SEAL KIT
PIN
STROKE CONTROL
HOSE #6 - 8MP - 8MP - 180LG
HOSE #6 - 8 MP - 8 MP 216 LG
HYD HOSE ONE
CYLINDER ASSEMBLY - LEVEL LIFT LEFT WING 3 x 8 SLAVE SN 10527 - 11270 MAR 1989 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
8721
8784
4675M
8780
8781
8753
8754
8785
4376
8786
8766
8354
163016
94514
691302
B651302
6513015
B65113A2
1
1
1
1
1
1
4
8
1
1
2
4
1
1
1
1
1
CYL HYD LEVEL LIFT 3 DIA
CAP (HYD. CYLINDER)
NUT PISTON
PISTON
TUBE
PISTON ROD
CLEVIS,OUTER
TIE ROD
NUT HEX 1/2-20 NF PL
HEAD
SEAL KIT
PIN-HYD. CYLINDER
HOSE #6 - 8MP - 8MP - 180LG
HOSE #6 - 8 MP - 8 MP 216 LG
HYD HOSE ONE
CYLINDER ASSEMBLY - LEVEL LIFT CENTER SECTION 3-1/2 x 8 SLAVE SN 10527 - 11270 MAR 1989 -
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
8719
8772
4705M
8768
8769
4706
8754
8773
4689
8774
8764
8354
163016
94514
691302
B651302
6513015
B65113A2
1
1
1
1
1
1
4
8
1
1
2
4
1
1
1
1
1
HYDRAULIC CYLINDER
CAP
NUT PISTON
PISTON
TUBE
PISTON ROD
CLEVIS,OUTER
TIE ROD
NUT HEX 9/16-18NF PL
HEAD
SEAL KIT
PIN-HYD. CYLINDER
HOSE #6 - 8MP - 8MP - 180LG
HOSE #6 - 8 MP - 8 MP 216 LG
HYD HOSE ONE
CYLINDER ASSEMBLY - LEVEL LIFT RIGHT WING 3-1/4 x 8 SLAVE SN 10527 - 11270 MAR 1989 - SEPT
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
8720
8778
4705M
8775
8776
4706
8754
8773
4689
8779
8765
8354
163016
94514
691302
B651302
6513015
B65113A2
1
1
1
1
1
1
4
8
1
1
2
4
1
1
1
1
1
HYDRAULIC CYLINDER
CAP
NUT PISTON
PISTON
TUBE
PISTON ROD
CLEVIS,OUTER
TIE ROD
NUT HEX 9/16-18NF PL
HEAD
SEAL KIT
PIN-HYD. CYLINDER
HOSE #6 - 8MP - 8MP - 180LG
HOSE #6 - 8 MP - 8 MP 216 LG
HYD HOSE ONE
CYLINDER ASSEMBLY - WING SECTION LIFT SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
PART NO.
QTY.
DESCRIPTION
8728
00756496
94517
7329
94507
8755
8751
8759
8758
00013901
00023100
8754
4690W
8757
8761
4675W
8354
162012
6511324
8763
1
1
1
1
1
1
1
1
1
1
1
8
1
4
1
2
2
1
-
HYDRAULIC CYLINDER
HOSE-#4-6MP-6MP-216LG
ADAPTER, HYD, STGHT RESTRICTOR
ADAPTER, HYD, REDUCER
CAP (HYD. CYLINDER)
PISTON
PISTON ROD
TUBE (HYD. CYLINDER)
NUT HEX 3/8 NC PL
HHCS 3/8 -16UNC 1-1/2 PL5
CLEVIS,OUTER
INSTALL SHEET-BELT TENSIONER&S
HEAD
TIE ROD
MANUAL-SR320 P/T HAY RAKE
PIN-HYD. CYLINDER
PIN,COTTER
BREATHER,1/2 SQ HD CORED
SEAL KIT
SEAL KIT
NOTE: This cylinder is used on non-hydraulic level lift wing.
DEFLECTOR - REAR LEFT AND RIGHT WING SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
00756876
00002700
00001800
02030700
2
10
10
4
WING REAR COVER
HHCS 1/2-13UNC 1-1/4 PL5
DEFLECTOR - RUBBER CENTER SECTION REAR SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
4
5
6
00756993
00756877
00756875
63066100
63065400
00015800
1
1
11
11
11
REAR RUBBER SHIELD KIT
REAR FLAP-CENTER SECTION
FLAP HOLD DOWN BAR
HHCS 3/8NCX1-1/2
FLATWASHER 3/8 PL HEAVY
DEFLECTOR - RUBBER FRONT CENTER SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
00758261
00758263
02030700
00001800
1
1
3
3
BAND RUBBER GD SR15 FRT CTR
PANEL RUBBER GD SR15 FRT CTR
HHCS 1/2-13UNC 1-1/4 PL5
DEFLECTOR - RUBBER FRONT WING SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
00758264
00758259
02030700
00001800
1
1
7
7
PANEL RUBBER GD SR15 WING
BAND RUBBER GD SR15 FRT WG
HHCS 1/2-13UNC 1-1/4 PL5
DEFLECTOR - RUBBER LH RH CENTER SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
00758262
00758260
02030700
00001800
1
1
2
2
PANEL RUBBER GD SR15 L&R CTR
BAND, RUBBER GD SR15 LH & RH
HHCS 1/2-13UNC 1-1/4 PL5
DRIVELINE ASSEMBLY - CAT 4 WING SN 10001 - 11209 APR 1988 - MAR 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
00756583
00757051
00757052
00752896
00754335
00755610
00775330
00775313
00759217
8393
00775319
00775332
00756075
00754153
00754167
00755444
00755445
00754154
00761075
1
1
2
1
2
1
1
6
1
1
1
1
1
1
1
2
1
1
DRIVESHAFT, WING
YOKE 1-3/4-20 #6 SLIDE COLLAR
KIT-SLIDE COLLAR REPAIR
CROSS BEARING SERIES 6
GREASE FITTING FOR TUBE
GREASE FTG.ELBOW 8MMP1.0 90
DRIVELINE IMPLEMENT HALF CAT 4
DRIVELINE TRACTOR HALF CAT 4
SCREW 1/2 LG END
BEARING RING
SHIELD OUTER HALF
SHIELD INNER HALF
CLUTCH & YOKE SERIES 6
YOKE INNER #6
PIN-ROLL #6 10MM X 75MM OUTER
TUBE, INNER 15-IV WING DS
TUBE OUTER 15-IV WING DS
YOKE-OUTER TUBE #6
SPRING,CENTERING
NOTE: Triangle Shaped Shaft & Tube; This Driveline has yellow shields.
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
00759213
00757051
00757052
00752896
00754335
00755610
00775330
00775313
00759217
8393
00775319
00775332
00756075
00754153
00754167
00755444
00755445
00754154
00761075
1
1
2
1
2
1
1
2
1
1
1
1
1
1
1
2
1
1
DRIVELINE
YOKE 1-3/4-20 #6 SLIDE COLLAR
DRIVELINE IMPLEMENT HALF CAT 4
DRIVELINE TRACTOR HALF CAT 4
SCREW 1/2 LG END
BEARING RING
SHIELD OUTER HALF
SHIELD INNER HALF
YOKE INNER #6
PIN-ROLL #6 10MM X 75MM OUTER
TUBE, INNER 15-IV WING DS
TUBE OUTER 15-IV WING DS
YOKE-OUTER TUBE #6
SPRING,CENTERING
NOTE: Triangle Shaped Shaft & Tube; This Driveline has black shields.
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
00756582
00753908
00757052
00753068
00754335
00755610
00756539
00757057
00754330
00754332
00754331
00753892
00753893
00754369
00756173
00757379
00757378
1
1
2
1
2
1
1
6
1
1
1
1
1
1
1
1
DRIVELINE,WING SERIES 80 W/SPL
YOKE, SERIES 8 1-3/4-20 SPLIN
HALF DRIVESHAFT W/CLUTCH FOR
PTO MALE WITH SAFETY GUARD
BOLT, NYLON - SAFETY SHIELD
LOCKING COLLAR OUTER SHIELD
LOCKING COLLAR INNER SHIELD
SHIELD KIT OUTER
SHIELD KIT INNER
SHIELD COMPLETE
YOKE W/INNER SHAFT
YOKE & TUBE ASSY OUTER
NOTE: Spline Shaft and Tube are no longer available as Assembly; Replace with PN 00757375 Assembly.
DRIVELINE ASSEMBLY - CAT 5 WING SN 10980 - 11270 MAR 1990 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
00757375
00753908
00757052
00753068
00754335
00755610
00757376
00757377
00754330
00754332
00754331
00753892
00753893
00754369
00756173
00757379
00757378
1
1
2
1
2
1
1
6
1
1
1
1
1
1
1
1
DRIVELINE 44R W/1-3/4X20
PTO OUTER W/SAFETY GUARD
D/L INNER HALF W/SAFETY GUARD
BOLT, NYLON - SAFETY SHIELD]
LOCKING COLLAR OUTER SHIELD
LOCKING COLLAR INNER SHIELD
SHIELD KIT OUTER
SHIELD KIT INNER
SHIELD COMPLETE
YOKE W/INNER SHAFT
YOKE & TUBE ASSY OUTER
NOTE: Triangle Shaped Shaft & Tube; This Driveline has yellow shields.
DRIVELINE ASSEMBLY - INTERMEDIATE SN 10001 - 11270 APR 1988 - SPET 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
00756581
00757049
00752896
00754399
00756075
00755610
1
2
1
1
2
DRIVESHAFT,INTERMEDIATE
OUTER YOKE 1-3/4-20
FLANGED DOUBLE YOKE *
* This Flange Assembly has 8 bolts in it - Category 4 x-kits.
DRIVELINE ASSEMBLY - MAIN 44R 540/1000 RPM SN 10001 - 11270 APR 1988 - 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
00758814
W827A
W840
00758815
00758816
00759212
W802B
W802B9
W815R
W825A
W821A
W812A
00749960
0650000100
8391
00600700
00010300
00010400
7AH882026
00001300
00001200
00760519
00752670
1
1
2
1
1
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
D/L 44R SQ SHFT 29PAINT BLACK
YOKE,CLP,1-3/4-20SP PAINT BLK
CROSS REPR KIT
DRIVELINE SHAFT & YOKE 44R 29
SHIELD OUTHE 29-1/8 LG 44R
RETAINER, NYLON BEARING
HSG,SHLD,QD YK PAINT BLACK
HSG,SHLD,21T CL YK PAINT BLACK
SHLD IN ASSY PAINT BLACK
YOKE 1-3/8-21 PAINT BLACK
YOKE,Q.D. 6BSPLN PAINT BLACK
YOKE SLEEVE PAINT BLACK
KIT,Q.D. REPAIR 1801 1802 1803
KIT-QD PIN, TRAILING PIN
Q.D. COLLAR KIT
HEXB 5/8 NC 3-1/4 PL5
LOCKWASHER 5/8 PL STD
NUT 5/8 NC HEX PL
C/S 1/2 X 3 1/4 NF 8
NUT,HEX 1/2 NC PL
RING, BEARING
GREASE FITTING 1/4-28 BOLT THD
8
9
10
11
12
13
14
15
16
17
18
19
20
21
NOTE: Square Shaft & Round Housing.
DRIVELINE ASSEMBLY - MAIN CV 1000 RPM SN 10001 - 11000 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
8
9
11
12
13
14
15
16
17
18
19
20
21
22
00755751
00753908
00753286
00759119
00752881
00753070
00753071
00753073
00755751
00755610
00753077
00755750
00755075
00753082
00753068
00758159
00758160
00760452
00759112
00757818
00757817
1
2
1
5
1
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
CV DRIVELINE,1000,1-3/8-21YOKE
CROSS & BEARING KIT #8-CV
YOKE-COLLAR & SNAP RING
GREASE FITTING
OUTER TUBE W/YOKE SERIES 8
MOWER HALF ASMBLY (1-3/4-20)
INNER TUBE W/YOKE SERIES 8
DRIVELINE,1000 CV CAT5 1-3/8GREASE FTG.ELBOW 8MMP1.0 90
N/A FROM VENDOR
YOKE, 1-3/8-21 SPLINE (1000RPM
PUSH PIN SET
COMPLETE SAFETY SHIELD
PIN,ROLL 3-1/2 LG
PIN, ROLL 3 LG
DRIVELINE,540 CV CAT 5 1-3/8-6
YOKE,INNER TUBE
TUBE,INNER D/L
TUBE,OUTER D/L
NOTE: Part No. 00755751 is no longer available as assembly. Replace by PN 00760453. Parts WILL NOT interchange
between assemblies; Triangle Shaft and Tube. The Driveline has yellow shields.
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
20
21
22
24
25
26
PART NO.
QTY.
DESCRIPTION
00760453
8478
8482
8382
7432
7433
8384
00760632
00760634
8489
00760636
8486
8393
00760640
00760641
7420
8949
8949
00759217
0921000345
00756005
00756004
8974
8391
00759556
00760665
00760667
1
1
1
1
2
2
1
1
1
1
1
2
1
1
1
1
1
8
1
1
1
1
1
1
1
1
DRIVELINE,1000 CV CAT5 1-3/8YOKE 1-3/8 21-SP
DOUBLE YOKE
FITTING,GREASE M8 X 1
YOKE-INBOARD
CROSS & BEARING KIT
SPRING PIN 10MM X 90MM
PROFILE-INNER SAGA
PROFILE & SLEEVE W.A.
INBOARD YOKE
YOKE 1-3/4-20 SPLINE A.S.
CROSS & BEARING KIT
BEARING RING
TUBE, OUTER SHIELD OVL
TUBE,INNER SHIELD ROUND
ASSY-BEARING & CV CONE
SHIELD CONE
SHIELD CONE
SCREW 1/2 LG END
CHAIN, SAFETY
DECAL-ROTATING DRIVELINE
DECAL-SHIELD MISSING
SUPPORT BEARING
Q.D. COLLAR KIT
KIT, SLIDE COLLAR
DRIVELINE-TRACTOR HALF PART OF
DRIVELINE IMPLEMENT HALF PART
NOTE: This is a replacement D/L NOT used on Production Model. Parts WILL NOT interchange with earlier driveline; Star
shaft and tube. This driveline has black shields.
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
00759242
00759232
00759233
00759234
00760453
00759236
00759237
1442
00759238
W827A
W840
00759239
00759240
00759241
4571
00760452
00760452
02961453
1
1
2
1
1
1
4
1
1
1
1
1
3
1
1
1
2
CV DRIVELINE,1000,1-3/8-21YOKE
SCQD YOKE 1000 RPM
BODY, ASY
KIT, CROSS & BEARING
DRIVELINE,1000 CV CAT5 1-3/8SHIELD, BELL
TUBE-SHIELD
BEARING, NYLON OUTER SHIELD
BRG-NYLON
CROSS REPR KIT
YOKE & SHAFT
SHIELD-INNER
SHIELD BRG
SLIDE COLLAR KIT
GREASE FITTING 1/4-28 TAPER 45
NOTE: Part No. 00759242 is no longer available as assembly. Replace by PN 00760453. Parts WILL NOT interchange
between assemblies; Spline Shaft and Tube. The Driveline has black shields.
DRIVELINE ASSEMBLY - MAIN CV 540 RPM SN 10001 - 11000 APR 1988 - APR 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
4
5
6
8
9
11
12
13
14
15
16
00754009
00753908
00753286
00752881
00753070
00753071
00753073
00753074
00755610
00760452
00753078
00755075
00753082
00753068
1
2
5
1
1
1
1
1
1
1
2
1
1
CV DRIVELINE 540,1-3/8-6 YOKE
CROSS & BEARING KIT #8-CV
GREASE FITTING
OUTER TUBE W/YOKE SERIES 8
MOWER HALF ASMBLY (1-3/4-20)
INNER TUBE W/YOKE SERIES 8
TRAC HALF 540 CV D/L
YOKE,1-3/8-6 (CV),TWIST COLLAR
PUSH PIN SET
COMPLETE SAFETY SHIELD
NOTE: Part No. 00754009 is no longer available as an assembly. Replace with PN 00760452. Parts will not interchange
between assemblies; Triangle shaft and tube. This driveline has yellow shields.
ITEM
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
20
21
22
24
25
26
PART NO.
QTY.
DESCRIPTION
00760452
7431
8482
8382
7432
7433
8384
00760632
00760634
8489
00760636
8486
8393
00760640
00760641
7420
8949
8949
00759217
0921000345
00756005
00756004
8974
8391
00759556
00760668
00760667
1
1
1
1
2
2
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
1
YOKE SLIDE COLLAR
DOUBLE YOKE
FITTING,GREASE M8 X 1
YOKE-INBOARD
CROSS & BEARING KIT
SPRING PIN 10MM X 90MM
PROFILE-INNER SAGA
PROFILE & SLEEVE W.A.
INBOARD YOKE
YOKE 1-3/4-20 SPLINE A.S.
CROSS & BEARING KIT
BEARING RING
TUBE, OUTER SHIELD OVL
TUBE,INNER SHIELD ROUND
ASSY-BEARING & CV CONE
SHIELD CONE
SHIELD CONE
SCREW 1/2 LG END
CHAIN, SAFETY
DECAL-ROTATING DRIVELINE
DECAL-SHIELD MISSING
SUPPORT BEARING
Q.D. COLLAR KIT
KIT, SLIDE COLLAR
DRIVELINE TRACTOR HALF PART OF
DRIVELINE IMPLEMENT HALF PART
NOTE: This is a replacement D/L, NOT used on Production Model. Parts WILL NOT interchange with earlier D/L; Star
Shaped Shaft & Tube. This driveline has black shields.
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
00759243
00759244
00759233
00759234
00759234
00759236
00759237
1442
00759238
W827A
W840
00759239
00759240
00759241
4571
00760452
00760452
02961453
1
1
2
1
1
1
4
1
1
1
1
1
3
1
1
1
2
CV DRIVELINE,540 1-3/8-6 YOKE
SC QD YOKE 540 RPM
BODY, ASY
SHIELD, BELL
TUBE-SHIELD
BEARING, NYLON OUTER SHIELD
BRG-NYLON
CROSS REPR KIT
YOKE & SHAFT
SHIELD-INNER
SHIELD BRG
SLIDE COLLAR KIT
GREASE FITTING 1/4-28 TAPER 45
NOTE: Part No. 00759243 no longer available as an assembly. Replace with PN 00760452 assembly. Parts will not
interchange between assembly; Splined shaft and tube. This driveline has black shields.
GEARBOX ASSEMBLY - 1000 RPM SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
14
15
16
17
18
19
20
21
22
23
24
25
27
29
30
31
32
00756741
00755613
00756900
00755615
00753238
00755617
00755618
00755619
00755620
00756943
00755622
00755626
00755627
00769938
00756945
00756899
00756946
00755632
00755633
00755634
00755635
00757342
00755637
02880900
00037200
00755624
00755623
163016
1
1
2
1
1
2
2
1
1
1
1
1
2
1
1
1
1
1
1
4
1
1
6
6
1
1
1
GEARBOX, 00756740 WITH LUBE
CASING
PINION 20 TEETH 1.2:1
BEARING
OIL SEAL
SHAFT
INTERNAL CIRCLIP
SHIM
EXTERNAL CIRCLIP
NUT M40X1.5
SHIM
PROTECTIVE SHIELD
OIL SEAL
BEARING, 30210
SHAFT
GEAR 24 TEETH 1.2:1
PIN, COTTER 3/16 X 2-3/8
SHIM
PLUG,3/8
CAP
HEXB METRIC 8-P1.25-16MM 5
PLUG, PRESSURIZED VENT
COVER
HHCS 3/4-10UNC 2-3/4 PL5
NUT TOPLOCK 3/4 NC PLC
NUT
WASHER 2.200 OD1.218 1DX.250
NOTE: Right Wing CCW Rotation Blades.
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
14
15
16
17
18
19
20
21
22
23
24
25
26
27
29
30
31
32
00755598
00755613
00755614
00755615
00753238
00755617
00755618
00755619
00755620
00755621
00755622
00755626
00755627
00769938
00755629
00755630
00755631
00755632
00755633
00755634
00755635
00757342
00755637
00755638
02880900
00037200
00755624
00755623
163016
1
1
2
1
1
2
2
1
1
1
1
1
2
1
1
1
1
1
1
4
1
1
1
6
6
1
1
1
GRBX ASSY RH C/W-IN-C/CW OUT
CASING
GEAR, 24 TEETH 1:1.5
BEARING
OIL SEAL
SHAFT
INTERNAL CIRCLIP
SHIM
EXTERNAL CIRCLIP
NUT,SLOTTED CASTLE
SHIM
PROTECTIVE SHIELD
OIL SEAL
BEARING, 30210
SHAFT
PINION, 16 TEETH 1:1.5
PIN, COTTER
SHIM
PLUG,3/8
CAP
COVER
SHIM
HHCS 3/4-10UNC 2-3/4 PL5
NUT
WASHER 2.200 OD1.218 1DX.250
NOTE: Left Wing CW Blade Rotation.
Center Section CCW Blade Rotation.
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
14
15
16
17
18
19
20
21
22
23
24
25
26
27
29
30
31
32
00755566
00755613
00755614
00755615
00753238
00755617
00755618
00755619
00755620
00755621
00755622
00755626
00755627
00769938
00755629
00755630
00755631
00755632
00755633
00755634
00755635
00757342
00755637
00755638
02880900
00037200
00755624
00755623
163016
1
1
2
1
1
2
2
1
1
1
1
1
2
1
1
1
1
1
1
4
1
1
1
6
6
1
1
1
GRBX ASSY C/W-IN-C/W OUT
CASING
GEAR, 24 TEETH 1:1.5
BEARING
OIL SEAL
SHAFT
INTERNAL CIRCLIP
SHIM
EXTERNAL CIRCLIP
NUT,SLOTTED CASTLE
SHIM
PROTECTIVE SHIELD
OIL SEAL
BEARING, 30210
SHAFT
PINION, 16 TEETH 1:1.5
PIN, COTTER
SHIM
PLUG,3/8
CAP
COVER
SHIM
HHCS 3/4-10UNC 2-3/4 PL5
NUT
WASHER 2.200 OD1.218 1DX.250
NOTE: Right Wing CCW Rotation Blades.
GEARBOX ASSEMBLY - CENTER SECTION 1000 RPM SN 10001 - 11270 APR 1988 - SEPT 1990
GEARBOX ASSEMBLY - CENTER SECTION 1000 RPM SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
14
15
16
17
18
19
20
21
22
23
24
25
27
29
30
31
32
00756622
00755613
00756900
00755615
00753238
00755617
00755618
00755619
00755620
00756943
00755622
00755626
00755627
00769938
00756945
00756899
00756946
00755632
00755633
00755634
00755635
00757342
00755637
02880900
00037200
00755624
00755623
163016
1
1
2
1
1
2
2
1
1
1
1
1
2
1
1
1
1
1
1
4
1
1
6
6
1
1
1
GEARBOX
CASING
BEARING
OIL SEAL
SHAFT
INTERNAL CIRCLIP
SHIM
EXTERNAL CIRCLIP
NUT M40X1.5
SHIM
PROTECTIVE SHIELD
OIL SEAL
BEARING, 30210
SHAFT
GEAR 24 TEETH 1.2:1
SHIM
PLUG,3/8
CAP
COVER
HHCS 3/4-10UNC 2-3/4 PL5
NUT
WASHER 2.200 OD1.218 1DX.250
NOTE: Center Section CCW Blade Rotation.
GEARBOX ASSEMBLY - DIVIDER 1000 RPM SN 10001 - 11100 APR 1988 - MAR 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
00755698
00756643
00756649
00753223
00753224
00756644
00753226
00756645
00755746
00755068
00753230
00753231
00753232
00756648
00755745
00753235
00755070
00753237
00753238
00753239
00753240
00753241
00755069
00756647
00756646
02845500
00010300
00010400
00001400
2
2
2
2
2
2
2
2
1
4
6
1
1
1
2
1
2
2
1
1
1
1
2
2
4
4
4
4
DIVIDER GEARBOX
SHAFT, 1-3/4-20 SPL WG OUTPUT
SNAP RING 40 UNI7436 .096 THK
BEARING
CIRCLIP, INTERNAL
SEAL,OIL 45X80X10
PLUG
SHIM, 69X79.9
GEAR, SIDE BEVEL 1000 T25A G/B
SHOULDER RING
HEXB METRIC 8-P1.25- 30MM PL5
SCHNORR WASHER
CASING
SHAFT, 1-3/4-20 CTR SHAFT
GEAR, CTR BEVEL, 1000 T25A G/B
SHIM
BEARING
INTERNAL CIRCLIP
OIL SEAL
OIL FILLER PLUG
COVER
BEARING
GASKET
SHIM, 65.3X79.7
BEARING, BALL
HEXB 5/8 NC 2 PL5
NUT 5/8 NC HEX PL
GEARBOX ASSEMBLY - DIVIDER 1000 RPM SN 11101 - 11270 MAR 1990 - OCT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
9
10
11
12
13
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
00757826
00758644
00758669
00758646
00758647
00758648
00758649
00769938
00758651
00758652
00758653
00758654
00758655
00758670
00758657
00758658
00758659
00755954
00565000
00758660
00758646
00758647
00758648
00758664
00758665
00758667
00758667
00758668
1
2
AR
AR
AR
2
4
2
2
4
1
2
1
1
1
2
18
18
1
2
1
1
1
1
2
1
1
GEARBOX 540 DIVIDER 1:1.15
HOUSING,DIVIDER GEARBOX
GEAR,20 TOOTH
SHIM, ADJUSTMENT .004 OR .1M
SHIM ,ADJUSTMENT O.5
CAP,HORIZONTAL HUB
BEARING,TIMKEN 30210
NUT,M55X1.5 ADJUSTING
ADAPTER, SEAL
SEAL, INPUT SHAFT
PLUG,1/2 PRESSURIZED VENT
BEARING,INPUT SHAFT
GEAR,23 TOOTH
SPACER,INPUT SHAFT
SHAFT,HORIZONTAL OUTPUT
HHCS, M10X1.5X32
LOCKWASHER M10
PLUG, HEX HEAD PIPE 1/8-27NPT
RING,RETAINING
CAP,INPUT
SHAFT,INPUT
SHIM .012
SHIM .012
SHIM,0.020
NOTE: 00757826 not serviced as complete unit, use 00759116
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
00756604
00756643
00756649
00753223
00753224
00756644
00753226
00753227
00753228
00755068
00753230
00753231
00753232
00756648
00753234
00753235
00755070
00753237
00753238
00753239
00753240
00753241
00755069
00756647
00756646
02845500
00010300
00010400
00001400
2
2
2
2
2
2
2
2
1
4
6
1
1
1
2
1
2
2
1
1
1
1
2
2
4
4
4
4
DIVIDER GEARBOX, COMER W/1-3/4
SHAFT, 1-3/4-20 SPL WG OUTPUT
SNAP RING 40 UNI7436 .096 THK
BEARING
CIRCLIP, INTERNAL
SEAL,OIL 45X80X10
PLUG
TAKE-UP RING
BEVEL PINION
SHOULDER RING
SCHNORR WASHER
CASING
SHAFT, 1-3/4-20 CTR SHAFT
CROWNWHEEL
SHIM
BEARING
INTERNAL CIRCLIP
OIL SEAL
OIL FILLER PLUG
COVER
BEARING
GASKET
SHIM, 65.3X79.7
BEARING, BALL
HEXB 5/8 NC 2 PL5
NUT 5/8 NC HEX PL
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
9
10
11
12
13
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
00757825
00758644
00758645
00758646
00758647
00758648
00758649
00769938
00758651
00758652
00758653
00758654
00758655
00758656
00758657
00758658
00758659
00755954
00565000
00758660
00758646
00758647
00758648
00758664
00758665
00758667
00758667
00758668
1
2
AR
AR
AR
2
4
2
2
4
1
2
1
1
1
2
18
18
1
2
1
1
1
1
2
1
1
GEARBOX 540 DIVIDER 1:1.15
HOUSING,DIVIDER GEARBOX
GEAR,20 TOOTH
CAP,HORIZONTAL HUB
BEARING,TIMKEN 30210
NUT,M55X1.5 ADJUSTING
ADAPTER, SEAL
SEAL, INPUT SHAFT
PLUG,1/2 PRESSURIZED VENT
BEARING,INPUT SHAFT
GEAR,23 TOOTH
SPACER,INPUT SHAFT
SHAFT,HORIZONTAL OUTPUT
HHCS, M10X1.5X32
LOCKWASHER M10
PLUG, HEX HEAD PIPE 1/8-27NPT
RING,RETAINING
CAP,INPUT
SHAFT,INPUT
SHIM .012
SHIM .012
SHIM,0.020
NOTE: 00757825 not serviced as complete unit, use 00769115
GEARBOX ASSEMBLY - LEFT WING 1000 RPM SN 10001 - 11270 APR 1988 - SEPT 1990
GEARBOX ASSEMBLY - LEFT WING 1000 RPM SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
14
15
16
17
18
19
20
21
22
23
24
25
27
29
30
31
32
00756739
00755613
00756899
00755615
00753238
00755617
00755618
00755619
00755620
00756943
00755622
00755626
00755627
00769938
00756945
00756900
00756946
00755632
00755633
00755634
00755635
00757342
00755637
02880900
00037200
00755624
00755623
163016
1
1
2
1
1
2
2
1
1
1
1
1
2
1
1
1
1
1
1
4
1
1
6
6
1
1
1
GEARBOX
CASING
GEAR 24 TEETH 1.2:1
BEARING
OIL SEAL
SHAFT
INTERNAL CIRCLIP
SHIM
EXTERNAL CIRCLIP
NUT M40X1.5
SHIM
PROTECTIVE SHIELD
OIL SEAL
BEARING, 30210
SHAFT
SHIM
PLUG,3/8
CAP
COVER
HHCS 3/4-10UNC 2-3/4 PL5
NUT
WASHER 2.200 OD1.218 1DX.250
NOTE: Left Wing CW Blade Rotation.
HOSE BRACKET ASSEMBLY SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
0651140100
0651150100
7A101112
5B10110
131000
1
1
2
2
2
WLDMT, HYD. HOSE BRKT
HYD. HOSE BRKT.
BLT 5/8 X 1-1/2
NUT 5/8 HEX, ZP
LOCK WASHER
HYDRAULIC VALVE ASSEMBLY - CLOSED CENTER SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
15
38
40
49
6514042
6514041
6514045
6514044
1
1
1
1
PLUG, CLOSED CTR
SEAL
SEAL ORING 1X1-1/8X0.070
WASHER BACKUP 1-1/8X1X1/16TK
Standard on Closed Valve
HYDRAULIC VALVE ASSEMBLY - CONVERSION PLUG SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
16
37
6514039
6514041
1
1
PLUG
SEAL
Standard on Open Valve
HYDRAULIC VALVE ASSEMBLY - DETENT W/SPRING ASSEMBLY SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
18
19
20
21
22
23
24
25
26
27
28
29
30
6514016
6514017
6514018
6514019
6514020
6514021
7E42012
6514022
7D42014
6514023
6514024
6514025
65140A54
1
1
1
1
1
1
1
1
4
1
1
1
1
HOUSING DETENT
SLEEVE
WASHER
SPRING CENTERING (25#)
COLLAR STEP
WASHER
C/S1/4 X 1 1/2 SK HD
CAP,END
BOLT
BALL 1/4 STEEL
SPRING
PLUG
WASHER
Standard quantities for one Detent Assembly 3 required per hydraulic valve.
HYDRAULIC VALVE ASSEMBLY - NON-ADJUSTABLE RELIEF SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
14
31
32
33
65140A50
6514034
6514035
6514036
1
1
1
1
RELEIF VALVE
O-RING
WASHER
SEAL
Standard on Open Center Valve
HYDRAULIC VALVE ASSEMBLY - NON-ADJUSTABLE RELIEF SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
17
34
35
36
6514037
6514034
3514035
6514036
1
1
1
1
PLUG, NO-RELIEF ASSY CROSS
O-RING
N/A
SEAL
Standard on Closed Center Valve
HYDRAULIC VALVE ASSEMBLY - OPEN/CLOSED CENTER VALVE SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
19E13/41/2
65140A47
65140A48
7E4204
65140A46
6514012
6514013
6514026
6514027
6514028
6514029
6514030
6514031
65140A50
6514042
6514039
6514037
2
3
3
6
3
6
6
3
3
3
3
3
3
1
1
1
1
PIPE BUSHING
HANDLE
KIT-PIN
SHCS 1/4 NC 1/2
BRKT
PLATE RETAINER
SEAL, O-RING
POPPET
SPRING,LIFT CHECK
SEAL, O-RING
PLUG
PLATE,1/16 ORIFICE
RETAINER
NON -ADJUSTABLE RELIEF ASSEMBLY (OPEN CENTER ONLY)
CLOSED CENTER ASSEMBLY (CLOSED CENTER ONLY)
CONVERSION PLUG ASSEMBLY
NO-RELIEF ASSEMBLY (CLOSED CENTER ONLY)
JACK ASSEMBLY - TOP WIND SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
00756655
00749892
00751685
1
1
1
PARKING JACK 5000# CAPACITY
PIN-JACK RETAINING
PIN-CLIP HAIR
LEVEL ROD ASSEMBLY SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
584042
00756926
00770485A
651102
5C1490
163012
15B1200
2
2
2
4
2
8
8
WLDMT-ROD CONTROL
WLDMT,CTR SEC CONTROL ROD
NUT,EXTENDED ADJUSTMENT
PIN-DRILLED
HEXNUT 7/8 JAM ZP
PINS-CTR 3/16 X 1 1/2
WASHER 3/4 P SAE
2 Assy Per Unit Reg.
LIFT SCREW SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
0656510000
651062F
00609200
02030300
00756579
1
2
2
2
1
MANUAL-LIFT SCREW
FITTING,GREASE (DRIVE TYPE)
HEXB 1 NC 4 GR5
NUT TOPLOCK 1 NC PLB
TOP LINK THREAD LOCK
Outboard Axle - 2 Req’d
MAINFRAME COMPONENTS S/N 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
00756720
00756719
00756718
65109
7A51812
5JRC5180
5710121
5F5180
0656270000
0656261000
1
1
1
1
2
2
3
6
2
2
WLDMT, CENTER SECTION
WLDMT, LEFT WING
WLDMT, RIGHT WING
PIN HINGE
HHCS 5/16X1-1/2 ZP
NUT TOPLOCK 5/16
COVER PLATE
NUT 5/16 NC WING
T,SPACER,LONG
SPACER,SHORT HINGE
6
7
8
9
SAFETY SHIELD ASSEMBLY SN 10001 - 11100 APR 1988 - MAR 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
0656130100
00757573
00757742
00004000
00751693
10182000
00011700
00011100
00015800
00024100
00017000
1
1
1
1
4
2
4
4
2
1
1
SHIELD, PRIMARY GEARBOX **
SHIELD - GBX
WLDMT, BRKT-GB SHIELD
NUT, 1/4-20NC PL WINGNUT
HHCS 3/8-16
FLATWASHER STD 1/4 PL
* Use existing G/B Bolts
** Used with G/B PN 00756604 & PN 00755698
SAFETY SHIELD ASSEMBLY SN 11101 - 11270 MAR 1990 - OCT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
00759781
00757573
00757742
00004000
00751693
10182000
00011700
00011100
00015800
00024100
00017000
00750959
00001300
1
SHIELD, PRIMARY GB
SHIELD - GBX +
WLDMT, BRKT-GB SHIELD +
NUT, 1/4-20NC PL WINGNUT +
HEXB METRIC 8-P1.25- 16MM PL5 +
HHCS 3/8-16 +
LOCKWASHER 5/16 PL STD +
FLATWASHER 3/8 PL STD +
NUT,TOPLOCK 3/8NC PLB +
FLATWASHER STD 1/4 PL +
HEXB,1/2NC X 1,ZP,GRD5
1
1
1
+ Three (3) Required per unit.
* NOTE: Used with G/B PN 00757825 & PN 00757826
SKID SHOE & SIDE SKIRT - OFFSET MODELS SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
00757071
00757066
00757069
2A381312
00001200
00001300
63066100
00748823
03101646
00013901
00011100
00757072
1
1
3
7
7
4
4
4
4
4
1
SKIRT LH CTR SC FOR 10 FT.
L/H CENTER SECTION SKIRT
SLIDE SHOE BAR
BOLT,PLOW 1/2 NC X 1-1/2 GR.5
NUT,HEX 1/2 NC PL
HHCS 3/8NCX1-1/2
HHCS 1/2-13UNC 1-1/2 PL5
LOCKWASHER,3/8,MEDIUM-ZP
NUT HEX 3/8 NC PL
REAR CONNECTOR
SKID SHOE - CENTER SECTION SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
00751305
00749171
02716500
2
4
4
WLDMT,SKID SHOE CS 15
HHCS 1/2-20UNF 1-1/4 PL5
NUT TOPLOCK 1/2 NF PLB
SKID SHOE & SIDE SKIRT ASSEMBLY SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
00756881
00756879
65203R
65203L
00002700
00001200
00748823
00001300
2A381312
00013300
1
1
1
1
14
20
10
20
6
4
RIGHT WING SIDE SKIRT WLDMT
LEFT WING SIDE SKIRT WLDMT
SHOES SLIDE
SHOES SLIDE
NUT,HEX 1/2 NC PL
HHCS 1/2-13UNC 1-1/2 PL5
BOLT,PLOW 1/2 NC X 1-1/2 GR.5
HEXB 1/2 NC 2 PL5
2
3
4
5
6
7
8
SLIP CLUTCH ASSEMBLY - SERIES 6 SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
00756075
00754199
00754203
00754201
00754202
00755599
00755600
00754314
00754301
00754302
00754303
00754304
8
1
1
4
1
2
1
1
1
8
1
BOLT & NUT M10X95 SELF LK NUT
PRESSURE PLATE
INNER PLATE
RING,CLUTCH LINING
BODY-FRICTION CLUTCH
NUT & BOLT 14X70MM
PLATE WITH HOLES
BUSHING
YOKE, FLANGED
SPRING CLUTCH
DIRT SHIELD
SLIP CLUTCH ASSEMBLY - SERIES 8 SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
00756173
00754199
00754203
00754201
00754202
00755599
00755600
00754314
00754301
00754083
00754303
00754304
8
1
1
4
1
2
1
1
1
8
1
BOLT & NUT M10X95 SELF LK NUT
PRESSURE PLATE
INNER PLATE
RING,CLUTCH LINING
BODY-FRICTION CLUTCH
NUT & BOLT 14X70MM
PLATE WITH HOLES
BUSHING
YOKE, CLUTCH SERIES 8
SPRING CLUTCH
DIRT SHIELD
SPRING POD ASSEMBLY - CENTER AXLE SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
0656460100
0656460110
0656460120
5JRC12100
371063A
65107A4
00002701
02023800
37107B13
0656460240
1
1
4
4
4
4
4
2
2
CENTER SPRING ASSY
UPPER SPRING WLD
LOWER SPRING WLD
NUT TOPLOCK 3/4
SPRING
GUIDE SPRING
FLATWASHER,3/4,TYPE AW,ZP
HEXB 3/4 NC 6-1/2PL
CLIP-X HAIR PIN
WLDMT-PIN
SPRING POD ASSEMBLY - OUTBOARD AXLE SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
00756999
00756907
163016
00756998
371063A
1
2
1
1
SPRING ASSY OUTBOARD AXLE
WLDMT, ROCKER ARM
PIN-ROCKER ARM
SPRING
TIRE SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
00008700
00025200
1
1
WHEEL, RIM ONLY
NOTAT TIRE & WHEEL
NOTE: 4 or 6 assemblies are needed, depending upon Axle requirement.
ALSO AVAILABLE
Recapped Airplane Tire on 5x12 rim - PN 00750016 (Not Shown)
Used 14" Airplane Tire and Wheel - PN 00749700 (Not Shown)
TONGUE ASSEMBLY USED ON 44R DRIVELINE SN 10527 - 11270 MAR 1989 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
6
7
8
9
10
11
651051
0811050020
651053
651054
7AH5121620
7AH5121636
5JRC12160
163016
D102
999201
1
1
1
2
2
1
3
2
1
1
WLDMT, TONGUE
WLDMT-TONGUE HITCH
ROD HITCH CONTROL
PIN-TONGUE PIVOT
C/S 3/4 X 2 1/2 NF 5
C/S 3/4 X 4 1/2 NF 5
NUT TOPLOCK 3/4 NF PLC
DECAL PTO SFT TO HTCH
NO LONGER AVAILABLE
TONGUE ASSEMBLY USED ON C.V. DRIVELINE SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
6
7
8
9
10
11
12
13
14
15
16
00756667
0811050020
00755841
651054
7AH5121620
7AH5121636
5JRC12160
163016
D102
999201
00758643
00755840
00770485A
5C1490
131400
1
1
1
2
1
3
2
1
1
1
1
1
1
1
1
WLDMT, TONGUE
WLDMT-TONGUE HITCH
TONGUE HITCH CONTROL ROD ASSY
PIN-TONGUE PIVOT
C/S 3/4 X 2 1/2 NF 5 *
C/S 3/4 X 4 1/2 NF 5
NUT TOPLOCK 3/4 NF PLC
DECAL PTO SFT TO HTCH
NO LONGER AVAILABLE
ROD,CONTROL *
WLDMT, CONTROL ROD *
NUT,EXTENDED ADJUSTMENT *
HEXNUT 7/8 JAM ZP *
LOCKWASHER 7/8
* Parts included in 00755841, Control Rod Assembly.
WEIGHT BOX SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
0656390100
0656390300
12BF6168
00012101
00757359
7A121016
00003901
00000200
15B1200
20A4012E
1
1
6
6
1
1
1
1
1
1
WEIGHT BOX WELD
COVER
SCREW 3/8 X 1 NC
LOCKWASHER 3/8 PL HVY
BRACE STRAP
C/S 3/4 X 2 NC ZP
LOCKWASHER 3/4 PL HEAVY
NUT 3/4 NC HEX PL
WASHER 3/4 P SAE
PIN
WHEEL HUB ASSEMBLY SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
PART NO.
QTY.
DESCRIPTION
00757241
00756576
00750434
00756577
00752177
00750614
00756490
02957044
00756493
00756492
00026200
00003500
00756489
0371242102
00756001
00756489
00756528
00756002
1
1
1
5
5
1
1
1
1
1
1
1
1
REF
REF
REF
REF
WHEEL HUB
BEARING CUP OUTSIDE
BEARING CONE INSIDE
BEARING CUP INSIDE
BOLT, STUD 1/2-20 NF X 1-7/8
NUT 1/2-20NF 90DEG.CONE LUG PL
NUT SLOTTED THIN 1 NF PLC
OIL SEAL HEAVY DUTY - TK-15
WASHER
DUST CAP
PIN-COTTER 5/32 X 1-1/2
ZERK FITTING 1/8 STRAIGHT
HUB W/ CUPS & STUBS
BEARING CONE
SPINDLE
HUB W/ CUPS & STUBS
WHEEL HUB ACCESS. KIT (INCLUDES 3-5 & 7-12)
SPINDLE DUAL WHEEL
WINCH & HOLD DOWN STRAP SN 10001 - 11270 APR 1988 - SEPT 1990
ITEM
PART NO.
QTY.
DESCRIPTION
1
2
3
4
5
6
7
8
9
0656200100
7A6168
7A81312
15B600
00012101
13800
00013901
00001200
B651202
651202
651203
65111
37107B13
1
3
2
1
3
2
3
2
1
1
1
2
4
STAND WINCH FS15
C/S3/8 X 1 NC
C/S1/2 X 1 1/2 NC
WASHER 3/8 SAE P
LOCKWASHER 3/8 PL HVY
LOCK WASHER
NUT HEX 3/8 NC PL
NUT,HEX 1/2 NC PL
WINCH & CABLE
WINCH
CABLE, 1/4 AIRCRAFT W/THIMBLE
BAR, TRANSPORT
CLIP-X HAIR PIN
10
11
12
SERVIS-RHINO
LIMITED
WARRANTY
1. LIMITED WARRANTIES
1.01.Servis-Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal
purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”)
that the goods purchased are free from defects in material or workmanship.
1.02.Manufacturer will replace for the Purchaser any part or parts found, upon examination at one of its factories, to be
defective under normal use and service due to defects in material or workmanship.
1.03.This limited warranty does not apply to any part of the goods which has been subjected to improper or abnormal use,
negligence, alteration, modification, or accident, damaged due to lack of maintenance or use of wrong fuel, oil, or
lubricants, or which has served its normal life. This limited warranty does not apply to any part of any internal
combustion engine, or expendable items such as blades, shields, guards, or pneumatic tires except as specifically found
in your Operator’s Manual.
1.04.Except as provided herein, no employee, agent, Dealer, or other person is authorized to give any warranties of any
nature on behalf of Manufacturer.
2. REMEDIES AND PROCEDURES.
2.01.This limited warranty is not effective unless the Purchaser returns the Registration and Warranty Form to Manufacturer
within 30 days of purchase.
2.02.Purchaser claims must be made in writing to the Authorized Dealer (“Dealer”) from whom Purchaser purchased the
goods or an approved Authorized Dealer (“Dealer”) within 30 days after Purchaser learns of the facts on which the
claim is based.
2.03.Purchaser is responsible for returning the goods in question to the Dealer.
2.04.If after examining the goods and/or parts in question, Manufacturer finds them to be defective under normal use and
service due to defects in material or workmanship, Manufacturer will:
(a) Repair or replace the defective goods or part(s) or
(b) Reimburse Purchaser for the cost of the part(s) and reasonable labor charges (as determined by Manufacturer)
if Purchaser paid for the repair and/or replacement prior to the final determination of applicability of the warranty
by Manufacturer.
The choice of remedy shall belong to Manufacturer.
2.05.Purchaser is responsible for any labor charges exceeding a reasonable amount as determined by Manufacturer and
for returning the goods to the Dealer, whether or not the claim is approved. Purchaser is responsible for the transportation cost for the goods or part(s) from the Dealer to the designated factory.
3. LIMITATION OF LIABILITY.
3.01.MANUFACTURER DISCLAIMS ANY EXPRESS (EXCEPT AS SET FORTH HEREIN) AND IMPLIED WARRANTIES
WITH RESPECT TO THE GOODS INCLUDING, BUT NOT LIMITED TO, MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.
3.02.MANUFACTURER MAKES NO WARRANTY AS TO THE DESIGN, CAPABILITY, CAPACITY, OR SUITABILITY FOR
USE OF THE GOODS.
3.03.EXCEPT AS PROVIDED HEREIN, MANUFACTURER SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO
PURCHASER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS, OR DAMAGE
CAUSED OR ALLEGED TO BE CAUSED DIRECTLY OR INDIRECTLY BY THE GOODS INCLUDING, BUT NOT
LIMITED TO, ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES RESULTING FROM
THE USE OR OPERATION OF THE GOODS OR ANY BREACH OF THIS WARRANTY. NOT WITHSTANDING THE
ABOVE LIMITATIONS AND WARRANTIES, MANUFACTURER’S LIABILITY HEREUNDER FOR DAMAGES
INCURRED BY PURCHASER OR OTHERS SHALL NOT EXCEED THE PRICE OF THE GOODS.
3.04.NO ACTION ARISING OUT OF ANY CLAIMED BREACH OF THIS WARRANTY OR TRANSACTIONS UNDER
THIS WARRANTY MAY BE BROUGHT MORE THAN TWO (2) YEARS AFTER THE CAUSE OF ACTION HAS
OCCURRED.
4. MISCELLANEOUS.
4.01.Proper Venue for any lawsuits arising from or related to this limited warranty shall be only in Guadalupe County,
Texas.
4.02.Manufacturer may waive compliance with any of the terms of this limited warranty, but no waiver of any terms shall
be deemed to be a waiver of any other term.
4.03.If any provision of this limited warranty shall violate any applicable law and is held to be unenforceable, then the
invalidity of such provision shall not invalidate any other provisions herein.
4.04.Applicable law may provide rights and benefits to purchaser in addition to those provided herein.
KEEP FOR YOUR RECORDS
ATTENTION: Purchaser should fill in the blanks below for his reference when buying repair parts and/or for proper machine
identification when applying for warranty.
Servis-Rhino Implement Model _______________________________ Serial Number ________________________________
Date Purchased __________________________________________ Dealer ______________________________________
ATTENTION:
READ YOUR OPERATOR'S MANUAL
RHINO®
Gibson City, IL 60936
800-446-5158
TO THE OWNER/OPERATOR/DEALER
To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and
the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily
find the information you need.
The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety
requirements of tractor operators:
REQUIRED OF THE OWNER:
1.
2.
3.
4.
Provide a Roll-Over-Protective Structure that meets the requirements of this Standard; and
Provide Seatbelts that meet the requirements of this paragraph of this Standard and SAE J4C; and
Ensure that each employee uses such Seatbelt while the tractor is moving; and
Ensure that each employee tightens the Seatbelt sufficiently to confine the employee to the protected
area provided by the ROPS.
REQUIRED OF THE OPERATOR
1.
2.
3.
4.
5.
6.
7.
8.
9.
Securely fasten seatbelt if the tractor has a ROPS.
Where possible, avoid operating the tractor near ditches, embankments, and holes.
Reduce speed when turning, crossing slopes, and on rough, slick, or muddy surfaces.
Stay off slopes too steep for safe operation.
Watch where you are going - especially at row ends, on roads, and around trees.
Do not permit others to ride.
Operate the tractor smoothly - no jerky turns, starts, or stops.
Hitch only to the drawbar and hitch points recommended by the tractor manufacturer.
When the tractor is stopped, set brakes securely and use park lock, if available.
Keep children away from danger all day, every day...
Equip tractors with rollover protection (ROPS) and keep all machinery
guards in place...
Please work, drive, play and live each day with care and concern for
your safety and that of your family and fellow citizens.
SR15/SR10 PL 06-05
Printed U.S.A.
P/N 00764578MB

SR15 SR10 MPB PUB 06-05 REV 04-06

Transcription

Similar documents

00764581MB---FM15 FM10 MPB PUB 07-05 Rev 10-11

Makia - irnsuperior

TURBO 120 MPB PUB 09-05 Rev 11-05

View full finding aid - Explore Chicago Collections

FL20/FL14

Flex10/Flex15 MAGNUM

Parts List

rotary mower parts - rotary cutter parts

TILLER PUB 02-03 Rev 05-07 PARTS

parts manual - Alamo Industrial

REPLACMENT PARTS FOR SHORTLINE SECTION

Oshkosh Corporation Price List March 2013

Die BUCHSTAVIER - Das Dosierte Leben

part`s manual