VT-A101RF RF Funkfernbedienung

VT-A101RF RF Funkfernbedienung
Die YULED™ VT-A101RF Funkfernbedienung ist eine moderne und formschöne RGB+W Funkfernbedienung mit
berührungssensiblen Farbauswahlrad. Die VT-A101RF kann 4 LED Kanäle (RGBW) ansteuern und ermöglich somit eine
nahezu unbegrenzte Farbauswahl. Es können mit einer Fernbedienung bis zu 6 Empfänger (Zonen) individuell angesteuert
werden. Im Master / Slave Mode können zudem mehrere VT-A151RF Empfänger gleichzeitig einer Zone zugeordnet werden.
Die Funkübertragung arbeitet im störungssicheren 868MHz Frequenzbereich.
- 4-Kanal (RGBW) LED Controller mit modernster Technik
- Funktechnik (868MHz) ermöglicht sichere Verbindung
- bis zu 6 Empfänger (VT-A151RF) können individuell angesteuert werden
- RGBW Technik ermöglicht eine Auswahl von über 100 Millionen Farben (!)
- 9 vorprogrammierte Farbprogramme
- Helligkeit und Programmgeschwindigkeit in 8 Schritten einstellbar
- individuelle Einstellung des Weißkanal (W) möglich
- Auto-OFF und Memory Funktion
- hohe Reichweite
- sehr hochwertige Verarbeitung und ein edles Design
- stabile, gummierte Drucktasten + berührungssensitives Farbrad
- gummierte Seiteteile für eine gute und sichere Handhabung
- Abmessungen: 130x48x18 mm
- Gewicht: 0,15 Kg
- 2 Jahre Garantie
- passender Empfänger: VT-A151RF
Bedienungsanleitung (engl. Version, Stand 01.03.2014)
1. Functions
Remote indicator
(upper right): when the indicator is on every operation will work on the remote. Indicator light will be
automatically off after 10 seconds of inactivity to conserve the batteries; when remote indicator went off, the remote will cease
to function until pressing
ON/OFF Switch
again to wake it up.
: Press to switch the remote on/off. The remote indicator glows red when the switch is on.
Dynamic modes
: 9 built-in dynamic modes switch, mode sequence changes upon pressing
each time:
mode1-pause-mode2-pause-mode3…mode9-pause-mode1……. Under RGBW 4-channel (default setting) output mode, color
sequence(R, G, B output terminal lighting) holding for 2 seconds each time: day white- cold white- warm white- day white…
：Under RGB 3-channel output mode, pressing
White color output
to day white, then cold white and back to warm white…;
Under RGBW 4-channel (default setting) output mode,
each time will change white from warm white
is used to control 4th channel only. Hold
channel ON, 2 seconds again 4th channel OFF, Brightness step sequence upon pressing
step 2～step 3…Step 8～step 1……
Speed down/up
Brightness down/up
2 seconds 4th
each time: step 8～step 1～
: To decrease and increase the speed of color changing in dynamic mode.
: To decrease and increase the brightness in dynamic or static modes.
Zones
: 6 independent lighting zones can be set. Multiple slave drivers can be paired to a same
zone. In the same zone with multiple drivers one driver must be set as Master and others Slaves. This allows all slaves to
follow the command from the master to ensure they run in sync in all modes.
2. Operations
Remote & driver paring: For the first time or to change driver(s) zone, to ensure the remote and target driver(s) communicate
normally, the driver(s) must be paired to the remote as Master or a Slave(s).
Master/Slave definition: press the paring button on the driver and the driver indicator will start flashing, at the same time press
(e.g., if you want to pair to zone 2(make sure the remote indicator is on) and press any one of
,when the driver indicator goes off and pairing has succeeded，this driver is defined as Master. Only one Master
can be set in each zone.
Press the paring button on the second driver and the driver indicator will start flashing, at the same time press
(e.g., if you
want to pair to zone 2(make sure the remote indicator is on) and touch the color wheel, driver indicator light will turn off to show
the pairing has succeeded，this driver is defined as Slave.
Use the same method to pair more slaves to zone 2 and the same method to pair the drivers Master or slaves to other zones.
2.1 Operation on multiple zones and single zone
Press
,
(e.g., to control zone 1,3 together, you can select all zones, make sure the remote indicator is on), touch color
wheel, the zone 1 & 3 lights turn on to the picked color, hold
for 2 seconds for the dynamic mode and all the
drivers(including the masters & slaves in zone 1,3) will run dynamically and synchronously.
Repeat the same method to add additional zones.
to shift the color-cycling speed or
Press
to dim down/up; The difference between multiple
zones operation & single zone operation is: in single zone, only one of
operations are the same as when in multiple zones.
has to be selected. All other
2.2 Independent-Zone ON/OFF
You can turn each zone on and off independently. e.g., zone
,
. simply push
that pressing
for 2 seconds to switch it off, push
,
,
is on, to switch off zone
for 2 seconds again will switch zone
while keeping zone
on again. Note
will not work when switching individual zones on and off.
Memory: The driver will memorize the last setting from the remote when the remote is switched off or in case of power failure.
Battery info: The remote indicator flashes 4 times in sequence and repeats this 3 times when you turn the remote on/off. This
indicates batteries low and should be replaced to restore proper function.
3. Troubleshooting
Symptoms
Lights do not
turn on
Causes
‘+’&‘-’ on driver connection reversed
Change connection ‘+’&‘-’ on driver
Remote is switched off
Switch on remote
Short circuit
over-current/over-temperature protection (driver
indicator is flicking quickly)
Can’t control
Solutions
Correct the connection
Wait for the driver to cool before
powering it back on
No batteries or batteries low
Install or replace new batteries
No control from remote
Keep within RF controlling distance
No pairing
Pair the remote and driver
4. Wiring diagram
① Wiring for single/multiple VT-A151 in single/multiple zone(s)
② Wiring with LED power amplifiers