CCG-RUMBA • Core™ 2 Duo CompactPCI ® CPU

Transcription

Product Information
CCG-RUMBA • Core™ 2 Duo CompactPCI ® CPU
Dual Core Processor
Dual-Screen Video • Dual Gigabit Ethernet • Dual Channel Memory • Triple SATA
Document No. 4434 • Edition 1 October 2010
The chipset is based on PCI Express technology
and has a powerful dual-screen integrated
graphics accelerator. Two Gigabit Ethernet
controllers are provided for high speed
connectivity. As an option, a mezzanine card is
available that allows to use the CCG-RUMBA in
addition as CompactPCI® Express system slot
controller (especially suited for hybrid dual
backplane systems).
The CCG-RUMBA is a versatile 4HP/3U (single
size Eurocard) CompactPCI® CPU board,
equipped with an Intel® Core™ 2 Duo
processor at 2.2GHz clock, and up to 4GB dual
channel capable DDR2 RAM. Three Serial ATA
channels are available for rear I/O. The
CCG-RUMBA has been designed especially for
systems which require dual core performance at
moderate power consumption.
CCG-RUMBA
© EKF
-1-
ekf.com
CCG-RUMBA • Dual Core CompactPCI® CPU
The CCG-RUMBA is provided with a high
performance mobile chipset (Intel® GME965)
which operates at up to 800MHz FSB and up to
667MHz DDR2 memory clock for optimum
system throughput. The on-board CF connector
module (C10-CFA) can accommodate a
CompactFlash memory card. As an alternate,
the 1.8-inch HDD/SSD disk module C30-PATA is
available as on-board mass-storage device
(option).
Local expansion interface connectors can be
optionally used to directly attach a mezzanine
companion side board, either for audio- and
legacy support, or equipped with PCI Express
based I/O circuitry. Mezzanine cards (aka side
boards) can carry in addition a 2.5-inch hard
disk drive. Also as an option, a suitable rear I/O
transition module (CCT-RIO) is available to the
CCG-RUMBA, which e.g. provides the Serial
ATA connectors.
Benefits of the CCG-RUMBA
<
<
<
<
<
<
<
<
<
<
<
<
<
<
<
CompactPCI System Slot Controller with or w/o Rear I/O
CompactPCI Express System Board Option (Mezzanine Expansion Card)
Hybrid Systems Option (Dual Backplane CompactPCI & CompactPCI Express)
Intel® Core™ 2 Duo Mobile Processor 2.2GHz (FSB 800MHz)
PCI Express Mobile Chipset Intel® GME965
2 x 2GB DDR2 Memory (Dual Channel Mode Capable)
Dual-Screen Graphics Controller
Dual Gigabit Ethernet Controllers
Triple SATA 3Gbps, Intel® Matrix Raid Storage Technology
Seven USB 2.0 channels
On-Board CompactFlash or on-Board 1.8-Inch Flash Disk
Variety of Mezzanine Expansion Boards Available with and w/o PCIe
TPM 1.2 Option (on Mezzanine Expansion Board)
Rear I/O Transition Module Option
RoHS compliant
CCG-RUMBA w C10-CFA
© EKF
-2-
ekf.com
CCG-RUMBA w C30-PATA 1.8-Inch HDD/SSD
C30-PATA Option
© EKF
-3-
ekf.com
Feature Summary CCG-RUMBA
Form Factor
Single size CompactPCI style Eurocard (160x100mm2), front panel width 4HP
(20.3mm)
Processor
Designed for Intel® Core™ 2 Duo second generation dual core mobile processors
(codename Merom), dynamic FSB switching, 800/667/533MHz FSB, maximum
junction temperature 100°C, Intel® Core Multiprocessing (CMP), Intel® Virtualization
Technology (VT), Intel® 64 Architecture
<
<
<
<
Chipset
Intel® GME965 (Codename Crestline) chipset comprised of:
<
Memory (RAM)
<
<
<
© EKF
GME965 Graphics/Memory Controller Hub (GMCH) with Intel® Graphics
Media Accelerator (GMA), generation 4 graphics engine, DirectX 10 and
OpenGL 2.0 support, 1.5 x 945GM graphics performance, ICH8M-E Enhanced
I/O Controller Hub, integrated GbE MAC, dual USB EHCI controllers (no shared
bandwidth), 3 x SATA 3Gbps, MST & RAID, unified SPI Flash support
Dual 200-pin SO-DIMM socket, DDR2 667 SDRAM (PC5300), 4GB (2 x 2GB)
maximum, single or dual channel mode operation, configurations:
<
<
Non Volatile
Memory (NVM)
CCG-1-RUMBA: 1.06GHz U7500 Intel® Core™ 2 Duo ULV, 533MHz FSB, 2MB
L2 cache, TDP ~10W (low power applications)
CCG-2-RUMBA: 1.2GHz U7600 Intel® Core™ 2 Duo ULV, 533MHz FSB, 2MB
L2 cache, TDP ~10W (low power applications)
CCG-4-RUMBA: 1.6GHz L7500 Intel® Core™ 2 Duo LV, 800MHz FSB, 4MB L2
cache, TDP 17W (general purpose applications)
CCG-8-RUMBA: 2.2GHz T7500 Intel® Core™ 2 Duo, 800MHz FSB, 4MB L2
cache, TDP 35W (performance applications)
256Mb, 512Mb, 1Gb, 2Gb technologies for x8 and x16 devices
Dual channel symmetric – memory addresses interleaved for increased
performance
Intel® Flex Memory Technology (dual channel interleaved mode with unequal
memory population) - memory module sizes maybe unequal in both the
channels
Dual channel asymmetric – memory module sizes may differ, including no
memory in the second channel (single-channel)
Channel 0 must be populated first
Intel® Turbo Memory card (codename Robson) on CCI-RAP mezzanine side board
optionally available
<
PCI Express Mini Card 1G Byte Flash
<
Microsoft® ReadyDrive and ReadyBoost (Windows® Vista)
<
Intel® Turbo Memory driver
-4-
ekf.com
Video
<
<
<
<
<
USB
<
<
<
<
<
<
<
Ethernet
<
<
<
<
PATA (IDE)
<
<
<
SATA
<
<
<
<
PCI Express
© EKF
Both analog monitor and digital flat-panel display support by DVI-I connector
(front panel), up to 2048x1536 pixel 16M colours @75Hz refresh rate
(analog), up to 1920 x 1200 pixel 16M colours @60Hz (digital), incorporates
PanelLink Digital technology (Silicon Image)
Dual screen capable up to 2 x 1920 x 1200 pixel (one display attached to the
front panel, the other to the back panel, or both to the front panel by means
of a DVI-I to DVI-D/VGA splitter cable, or secondary DVI-D connector on
mezzanine side board)
Front panel option: D-Sub (female HD15) VGA connector available, replaces
DVI-I connector
Rear I/O option: Analog video output configurable (BIOS) across J2/P2 CCT-RIO
rear I/O transition module
Mezzanine option: Secondary DVI-D connector at mezzanine card front panel
allows for dual digital flat panel operation, suitable mezzanine modules e.g.
CCH-MARIACHI, CCI-RAP or CCJ-RHYTHM
All ports over-current protected, data transfer rate of up to 480Mbps,
conforming to USB2.0
2 x USB type A connector (front panel)
3 x USB ports J2/P2 Rear I/O option (CCT-RIO rear I/O transition module)
up to 2 x USB ports expansion interface option (in use by several mezzanine
side boards)
USB Flash drive module C15-DON option (USB stick on-board module)
USB module C33-DON option (same as C15-DON, bottom mount)
Dual EHCI / five UHCI controllers provided by ICH8M-E
Two 10/100/1000Mbps Gigabit Ethernet controllers, accessible via RJ45 jacks
from the front panel
ETH1 equipped with Intel® 82566 PHY (MAC provided by ICH8M-E)
ETH2 equipped with Intel® 82573 GbE controller connected to local PCIe lane
Option ETH1 Gigabit Ethernet configurable (BIOS setup) across J2/P2 with
attached CCT-RIO rear I/O transition module
Ultra ATA/100 connector, handover to CCH-MARIACHI/CCJ-RHYTHM
mezzanine expansion board with optional on-board 2.5-inch hard disk drive or
external device
CompactFlash socket C10-1D-CFA supplied for a CFA ATA memory card or
Microdrive®
Option 1.8-inch on board Hard Disk (HDD) or Flash disk (SSD) module C30PATA, replaces CompactFlash facility
Triple-channel Serial ATA 3Gbps available for J2/P2 rear I/O option
Suitable rear I/O transition module CCT-RIO (2 x system internal SATA, 1 x
eSATA for attachment of external devices)
Intel® Matrix Storage Technology MST (Raid 1, 0, Matrix Raid)
Additional PCIe to SATA controller on mezzanine side boards CCI-RAP, CCKMARIMBA
4-Lane PCIe (1 Link) connector for CCJ-RHYTHM and other mezzanine expansion cards
(side boards)
-5-
ekf.com
Mezzanine
Side Board
I/O
<
J2/P2 Rear I/O
<
<
<
<
<
<
<
<
<
<
<
<
LPC/USB/Audio (Super-I/O, USB and Azalia HD Audio) expansion interface
connector
ATA/IDE expansion connector
PCI Express 4-lane (configurable as 1 link x 4) high speed expansion connector
SDVO secondary digital graphics port high speed expansion connector
Suitable mezzanine companion side boards available:
<
C10-CFA: CompactFlash adapter module (CF Card internally)
<
C13-RD: CompactFlash adapter module (CF Card front panel slot,
resulting in a 6HP assembly)
<
C15-DON: On-board USB stick module (USB Flash disk)
<
C17-CFA: Bottom Mount CF Card Adapter
<
C23-SATA: PCIe to SATA controller, USB SSD, COM ports
<
C30-PATA: 1.8-inch HDD/SSD module
<
C33-DON: Bottom mount alternate to C15-DON
<
CCE-PUNK: Front panel 2 x COM, 2 x USB, 2 x 1394a FireWire, on
board hard disk
<
CCH-MARIACHI: Front panel options secondary DVI-D, COM, USB,
audio in (analog), audio out (analog), digital audio. Option on board
PATA hard disk drive 2.5-inch, option TPM 1.2
<
CCI-RAP: Front panel options secondary DVI-D, Wireless (Antenna),
IEEE 1394 (FireWire), COM. Two PCI Express Mini Card sockets (WLAN,
GSM, Wimax, Intel® Turbo Memory), on board socket for USB Flash
disk. Option on board mezzanine storage module C20 provides up to
2 SATA hard disk drives 2.5-inch (RAID capable), option TPM 1.2
<
CCJ-RHYTHM: Front panel options DVI-D, COM, USB, IEEE 1394
(FireWire). CompactPCI Express system slot controller function by on
board 6-port 24-lane PCIe switch. Option on board PATA hard disk
drive 2.5-inch, option TPM 1.2
<
CCK-MARIMBA: PMC/XMC module carrier. Option on board
mezzanine storage module C20-SATA
<
CCL-CAPELLA: 4 x Gigabit Ethernet, IEEE 1394 (FireWire), option on
board mezzanine storage module C20-SATA
<
CCO-CONCERT: HD Audio, 2-4 x RS-232, secondary DVI-I (option),
several on-board SATA drive options 1.8-inch and 2.5-inch (up to 2
drives), USB Flash Disk option, option TPM 1.2
3 x Serial ATA (SATA), 2 x system internal SATA connectors, 1 x external eSATA
connector
1 x Gbit Ethernet (switched by BIOS between front panel I/O and rear I/O)
3 x USB
VGA Analog Video (switched by BIOS between front panel I/O and rear I/O)
Keyboard, Mouse
COM port (TTL Level)
Suitable rear I/O transition module CCT-RIO available
Custom specific rear I/O transition modules available on request
CompactPCI®
ICH8M-E integrated 32-bit PCI bridge, 133MBps CPCI master, additional PCI arbiter in
PLD for fully figured 8-slot CompactPCI backplane
CompactPCI®
Express
<
<
<
© EKF
CCG-RUMBA works also as CompactPCI Express System Board (system slot
controller) by optionally available mezzanine expansion card (side board) CCJRHYTHM
CPCIe 4-Link configuration (4-lanes each), for up to 4 CPCIe peripheral slots
type 1 and/or type 2 on a passive CPCIe backplane
Suitable also for hybrid CPCI/CPCIe systems/backplanes (e.g. Schroff)
-6-
ekf.com
Secure
Computing
<
Option Trusted Platform Module TPM 1.2 according to Trusted Computing
Group specifications, available on several mezzanine boards such as
CCH/CCI/CCJ
Crypto engine silicon brands Infineon or Atmel at users choice
BIOS
<
<
<
Phoenix BIOS with EKF enhancements for embedded systems
SPI Flash memory 2 x 16/32/64 Mb
Updates available from website ekf.com
Drivers
(All Major OS)
<
<
<
<
Intel® graphics driver
Intel® networking driver
Intel® Matrix Storage Manager software
Intel® Turbo Memory driver
Thermal
Conditions
Environmental
Conditions
<
<
<
<
<
<
<
Operating temperature: 0°C ... +70°C (CPU dependent)
Storage temperature: -40°C ... +85°C, max. gradient 5°C/min
Humidity 5% ... 95% RH non condensing
Altitude -300m ... +3000m
Shock 15g 0.33ms, 6g 6ms
Vibration 1g 5-2000Hz
Coated PCB available (option)
EC Regulations
<
<
EN55022, EN55024, EN60950-1 (UL60950-1/IEC60950-1)
2002/95/EC (RoHS)
MTBF
tbd
© EKF
<
-7-
ekf.com
Typical Power
Requirements
1)
Intel®
SpeedStep®
Frequency Modes
LFM: Low
Frequency Mode,
HFM: High
Frequency Mode
2)
+3.3V +0.17V/-0.1V
+5V +0.25V/-0.15V
Board
MaxPower
LFM/HFM 1)
WinXP Idle
LFM/HFM 1)
MaxPower
LFM/HFM 1)
WinXP Idle
LFM/HFM 1)
CCG-1-RUMBA
4.9/4.9A 2)
1.7/1.7A 2)
2.1/2.6A
1.0/1.1A
CCG-4-RUMBA
5.3/5.3A 2)
1.8/1.8A 2)
3.1/4.0A
1.2/1.5A
CCG-8-RUMBA
5.3/5.3A 2)
1.8/1.8A 2)
3.1/7.8A
1.4/2.2A
Add 0.8A per Ethernet Port @1Gbps or 0.2A per Ethernet Port @100Mbps.
Performance
Rating
Measured with
PCMark2005
under Windows
XP, 2 x 1GB
DDR2 667
Board
Processor
CPU/MEM Score
CCG-1-RUMBA
U7500
2330
CCG-4-RUMBA
L7500
3090
CCG-8-RUMBA
T7500
3760
3820 (WEPOS/SP3)
Items are subject to changes
C17-CFA Bottom Mount CompactFlash Adapter
© EKF
-8-
ekf.com
Block Diagram CCG-RUMBA
Core™2
Duo
Core™2 Duo T7500
2.2GHz FSB800 4MB L2
LV Core™2 Duo L7500
Simplified Block Diagram
CCG-RUMBA
2.2GHz
ULV Core™2 Duo U7500
MEROM FSB
Panel
Link
SDVO1
VGA
GME965
RGB
GMCH
SDVO2
Crestline
iAMT
ME
DVI2
Opt. Mezz. Exp.
CCH-MARIACHI
CCJ-RHYTHM
top/
bottom
DMI x 4
VGA
SDVO2
D-SUB
DDR2 533/667
2GB/4GB
Dual Channel
C10-CFA
CompactFlash
ATA
IDE I/F
DVI1
SO-DIMM 200
SO-DIMM 200
533/667/800
Video
IDE
Opt. Mezzanine
Expansion Board
CCH-MARIACHI
CCJ-RHYTHM
USB
VGA
ICH8M-E
SPI
USB
KB/MS
SIO
87
61
LPC
HD Audio
PCI
82566
MM
USB
COM
GPIO
iAMT Gb
Ethernet
Front Panel I/O
GbE
2
Gb ETH
J2
BIOS & FW
2 x 16/32Mb
82
573
SPI
FlashSPI
Flash
Gigabit
Ethernet
Glue Logic
PCI Arbiter
4 x PCI
isp
MACH
x 4 PCIe
PCIe
Expansion I/F
top/
bottom
7 x PCI
32bit/33MHz
CompactPCI
GbE
1
PCIe
iAMT
Opt. Rear I/O
CCT-RIO
SATA II
RAID
Rear I/O
Kumeran
GLCI
J1
Opt. Mezz.
Exp. Board
CCH-MARIACHI
CCJ-RHYTHM
© EKF
-9-
ekf.com
Component Assembly CCG-RUMBA (Top View)
PATA/IDE
1
DVI
-I
PCI Express x 4
1
2GB DDR2 SODIMM
VGA
Core™ 2 Duo
2GB DDR2 SODIMM
USB
C10
CompactFlash
ATA
USB
GbE-1
AMT
LPC/USB/AUDIO
1
2.2GHz
GM965
82
566
ICH8M-E
GbE-2
82
573
RAID • AMT
GMCH
SDVO-2
1
©EKF
© EKF
CCG-RUMBA
-10-
ekf.com
ekf.com
Front Panel Options CCG-RUMBA
CCGRUMBA
CCGRUMBA
D
V
I
I
USB
P
G
G-ETH
G
P
© EKF ekf.com
V
G
A
H
D
USB
P
G
G-ETH
G
P
H
D
CCG-RUMBA DVI/VGA
© EKF
-11-
ekf.com
CCG-RUMBA (Top View)
© EKF
-12-
ekf.com
C10-CFA (Top Mount CF Card Adapter)
The CCG-RUMBA comes with a CompactFlash
adapter module (C10-CFA), which is suitable to
hold a silicon memory CF card, operated in 'True
IDE Mode' similar to a hard disk. If the CCGRUMBA is accompanied by a mezzanine
expansion module such as the CCH-MARIACHI
or CCJ-RHYTHM, the position of the C10-CFA
CompactFlash adapter module changes to the
mezzanine card.
Optionally an on-board 1.8-inch drive (HDD or
SSD) module is available (C30-PATA). When
ordered, it replaces the CompactFlash adapter
module (please request for a special solution
which allows to use both the CF slot and the
1.8-inch drive simultaneously). The C30-PATA
allows to maintain the 4HP envelope and can
be combined with additional expansion side
boards on the CCG-RUMBA.
C30-PATA on-Board Drive Module
© EKF
-13-
ekf.com
Available as a rear I/O expansion board to the
CCG-RUMBA CPU card, the CCT-RIO is provided
with several I/O port connectors, to be used
either in addition to the CCG-RUMBA front
panel connectors or alternatively. Being mainly
a passive rear I/O transition module, groups of
signals from the CCG-RUMBA CPU board are
passed across the CompactPCI J2/P2 connector
to the CCT-RIO. Some of the data lines are
available locally on the CCT board for system
internal wiring only, while other connectors
such as VGA-Video and Gigabit Ethernet are
mounted into the back panel for external use.
USB and SATA (eSATA) channels are provided
both on-board and externally.
Typically the CCT-RIO ist equipped with a 4-HP
rear panel (20.3mm width). As a custom
specific option, an 8-HP panel is available with
additional connectors.
Utilization of the CCT-RIO transition module
adds a level of I/O functionality that is not
available with the CCG-RUMBA CPU board
alone. Further on, swapping the CPU card is
simplified by means of rear I/O, which is
important for efficient system maintenance
(MTTR). Be sure to have ordered a CCG-RUMBA
rear I/O capable version and also the CPCI
backplane suitable for rear I/O in order to use
the CCT-RIO transition module.
CCT-RIO (Shown with on-Board USB Stick)
© EKF
-14-
ekf.com
Block Diagram CCT-RIO
VGA
Block Diagram
CCT-RIO
Video
ADM
211
COM
RS-232E
Ethernet
USB
ETH
LM
3526
USB
SATA
USB
Option 8HP
Rear Panel
I/O
CCD-CALYPSO
J2 Rear I/O
KB
MS
P-POW
SATA
KB/MS
4HP
Rear Panel
I/O
J2
COM
TTL
J-COM
COM
Rear I/O
GPIO
+5V
Single Slot Backplane EKF Part No. 932.4.01.080
© EKF
-15-
ekf.com
P-CU
P-SA
1
1
1
SATA0
ETH
1
USB7
1
P-PS2
SATA1
P-POW
4
J-COM
1
1
©EKF
1
3
SATA2
eSATA
1
USB-Stick or Internal Device
CCT-RIO
© EKF
USB
P-232
P-GPIO
VGA
Component Assembly CCT-RIO (Top View)
CCT-RIO
ekf.com
CCG-RUMBA w CCT-RIO (Similar Picture)
© EKF
-16-
ekf.com
CCT-99-RIO Custom Specific for Internal I/O Usage
CCT-99-RIO Custom Specific for Internal I/O Usage
© EKF
-17-
ekf.com
Back Panel CCT-RIO
CCTRIO
V
G
A
G
B
E
T
H
C
O
M
U
S
B
e
S
A
T
A
K
B
/
M
S
CCT-RIO 4/8HP
© EKF
-18-
ekf.com
CCG-RUMBA Mezzanine Expansion Options
The CCG-RUMBA is provided with several stacking connectors for attachment of a mezzanine
expansion module (aka side board), suitable for a variety of readily available mezzanine cards (please
refer to www.ekf.com/c/ccpu/mezz_ovw.pdf for an overview). EKF furthermore offers custom specific
development of side boads (please contact sales@ekf.de).
Legacy Expansion
IDE - PATA
C10-CFA
C17-CFA
C30-PATA
CCE-PUNK
and many more
LPC/USB/AUDIO
J-IDE
LPC, Audio, USB
PCI Express 1x4 / 4x1
C23-SATA
CCH-MARIACHI
CCI-RAP
CCJ-RHYTHM
CCK-MARIMBA
CCL-CAPELLA
C23-SATA
CCI-RAP
CCJ-RHYTHM
CCK-MARIMBA
CCL-CAPELLA
LPC/USB/AUDIO
J-EXP
J-PCIE
CCG-RUMBA
© EKF ekf.com
J-SDVO
CCG-RUMBA
SDVO Video Output
(DVI-D, HDMI, DisplayPort, VGA)
Mezzanine Module
CCH-MARIACHI
CCI-RAP
CCJ-RHYTHM
(Side Board)
Expansion Options
Most mezzanine expansion modules require an assembly height of 8HP in total, together with the
CPU carrier board (resulting from two cards at 4HP pitch each).
In addition, reduced size mezzanine modules are available for mass storage, which maintain the 4HP
envelope (C10-CFA, C30-PATA), for extremely compact systems. Furthermore these small size modules
may be combined with the full-size expansion boards (that means an assembly comprised of 3 PCBs).
© EKF
-19-
ekf.com
The picture below illustrates a typical mezzanine stack, comprised of the CPU carrier board (shared
front panel from 4HP to 12HP, individually tailored to customers configuration), a mezzanine side
board with a variety of PCIe and legacy interface functions (front panel and/or rear I/O), and a SATA
storage module (either SSD or hard disk, 1.8-inch or 2.5-inch, dual or single drive, RAID option).
© EKF
-20-
ekf.com
Side Boards
The CCG-RUMBA is provided with several stacking connectors for attachment of a mezzanine
expansion module (aka side board), suitable for mezzanine modules as described on the following
pages. EKF furthermore offers custom specific development of mezzanine cards (please contact
sales@ekf.de).
CCG-RUMBA Expansion Port Connectors (Similar Picture)
Sample Side Boards
© EKF
-21-
ekf.com
C15-DON (Top) & C33-DON (Bottom)
In order to attach an internal USB dongle or
USB stick (Flash Drive) to a CompactPCI® CPU
board or side card, the C15-DON or C33-DON
can be used, connected to the EXP expansion
port connector. These adapters are functionally
identical, however differ with respect to their
mounting position.
The C15-DON is suitable for top mount,
typically on a mezzanine side card such as the
CCB-BOSSANOVA, thus maintaining the overall
assembly stack height. The C33-DON has been
designed for bottom mount, directly under the
CPU board, hence additional 4HP front panel
width would have to be considered.
USB Flash Drive Options C15 (Top Mount) • C33 Bottom Mount)
© EKF
-22-
ekf.com
C15-DON (Shown w. USB Stick)
C33-DON (Shown w. USB Stick)
© EKF
-23-
ekf.com
CCE-PUNK Mezzanine Module
Available as a mezzanine companion board to
the CCG-RUMBA CPU card, the CCE-PUNK is
provided with high-speed communication
channels such as FireWire™ and USB, and
common legacy I/O ports as well.
Interconnection between the CCE-PUNK I/O
module and the CPU carrier board is achieved
by several expansion connectors, which
comprise the PCIe (PCI Express), LPC (Low Pin
Count) and ATA/IDE interfaces.
As an option, the CCE-PUNK is available with a
rugged on-board 2.5-inch hard disk drive (1.8inch as a mezzanine module).
The CCE-PUNK will be attached on top of the
CPU board, and shares its front panel typically
with the host CPU carrier board (8HP front
panel width in total).
CCG-RUMBA CPU Board with CCE-PUNK Side Board (Similar Picture)
© EKF
-24-
ekf.com
CCH-MARIACHI Mezzanine Module
As an option, the CCG-RUMBA can be replenished with the CCH-MARIACHI mezzanine card. The main
purpose of the CCH mezzanine module is to complement the CCG-RUMBA with a secondary DVI-D
video connector and by adding legacy functions, such as analog/digital audio and RS-232 serial I/O
(COM ports). Furthermore the CCH can carry a 2.5-inch hard disk, which offers higher storage
capacity compared to the 1.8-inch Flash SSD drive or CF Card. The CCH-MARIACHI can be mounted
either on top or underneath the CCG-RUMBA, which results in a 8HP building block, suitable for CPCI
backplanes with either rightmost or leftmost aligned system slot (while the CPCI backplane system slot
matches the CCG-RUMBA, the CCH-MARIACHI mezzanine board is usually positioned outside the CPCI
backplane).
Major Stuffing Options CCH-MARIACHI
COM-A + USB,
or DVI-2
Either secondary DVI-D video output connector, or RS-232E COM port
connector (male D-Sub 9) and USB receptacle
Analog Audio
Azalia HD-Audio codec, line in / microphone in, line out / headphones out,
3.5mm audio jacks
COM-B
or Digital Audio
Either RS-232E COM port connector (male D-Sub 9), or digital audio S/PDIF
(female D-Sub 9)
FWH2
Option secondary firmware hub on board, Low Pin Count (LPC) interface
TPM1.2
Option Trusted Platform Modul (e.g. Infineon SLB 9635)
2.5-Inch HDD
Parallel ATA (Ultra ATA/100) disk drive option
CCG-RUMBA & CCH-MARIACHI with Hard Disk
© EKF
-25-
ekf.com
Front Panel Options CCH-MARIACHI
CCH-
CCGRUMBA
MARIACHI
C
O
M
D
V
I
CCH-
CCGRUMBA
MARIACHI
C
O
M
D
V
I
U
S
B
P
G
L-IN
G-ETH
A
U
D
I
O
G
P
H
D
CCG-RUMBA
DVI
L-OUT
USB
D
V
I
D
V
I
I
2
I
2
USB
P
G
L-IN
G-ETH
A
U
D
I
O
G
P
L-OUT
P
G
L-IN
G-ETH
H
D
B
CCH-MARIACHI
2 x RS-232
CCG-RUMBA
DVI
A
U
D
I
O
H
D
CCH-MARIACHI
Digital Audio
A
U
D
I
O
G
P
D
I
G
C
O
M
CCHMARIACHI
D
V
I
U
S
B
© EKF • ekf.com
USB
draft only - do not scale • © EKF • ekf.com
I
CCGRUMBA
D
V
I
A
A
I
CCHMARIACHI
CCG-RUMBA
DVI
L-OUT
C
O
M
B
CCH-MARIACHI
DVI & RS-232
CCGRUMBA
USB
P
G
L-IN
G-ETH
A
U
D
I
O
G
P
L-OUT
D
I
G
H
D
CCG-RUMBA
DVI
A
U
D
I
O
CCH-MARIACHI
DVI & Digital Audio
CCG-RUMBA & CCH-MARIACHI with Secondary DVI and Digital Audio
© EKF
-26-
ekf.com
CCI-RAP Mezzanine Module
As an option, the CCG-RUMBA is available together with the CCI-RAP mezzanine expansion card (side
board). The CCI-RAP is equipped with two PCI Express Mini Card sockets, suitable e.g. for wireless
modules such as WLAN or GSM, and Flash Turbo Memory as required by Microsoft® ReadyDrive and
ReadyBoost (Windows® Vista). In addition, the CCI-RAP provides a secondary DVI-D video connector,
two FireWire receptacles and a RS-232 serial I/O COM port connector. Furthermore the CCI-RAP can
carry another mezzanine card, the C20-SATA storage module, which is populated with up to two 2.5inch SATA hard drives, either individually addressable or configured as RAID. The CCI-RAP/C20-SATA
must be mounted on top of the CCG-RUMBA, which results in a 8HP or more building block, suitable
for CPCI backplanes with a rightmost aligned system slot (while the CPCI backplane system slot
matches the CCG-RUMBA, the CCI-RAP mezzanine board is usually positioned outside the CPCI
backplane).
Major Stuffing Options CCI-RAP
DVI-2 or
COM-A
Either secondary DVI-D video output connector, or RS-232E COM port
connector (male D-Sub 9)
Antenna
Option one or two front panel mounted adapter connectors to WLAN/GSM
mini card antenna output, typically custom specific, e.g. Hirose to SMB
IEEE 1394a
FW1, FW2
On-board PCIe IEEE 1394 (FireWire) controller, 2-port PHY
COM-B
RS-232E COM port connector (male D-Sub 9)
PCIe Mini Card
Two sockets according to the PCI Express Mini Card standard, suitable for
WLAN/Wimax/GSM cards or Intel® Turbo Memory, socket 1 connected to onboard SIM card holder (GSM)
FWH2
TPM1.2
USB Flash
Option pin header for USB Flash disk module (e.g. M-Systems uDOC MD1665,
SimpleTech SLUFDM, Intel Z-U130)
SATA Storage
C20-SATA mezzanine card, 1 or 2 SATA hard disk drives 2.5-inch,
configuration as RAID or individual drives
© EKF
-27-
ekf.com
Front Panel Options CCI-RAP
CCGRUMBA
CCIRAP
CCGRUMBA
C
O
M
D
V
I
I
D
V
I
I
A
USB
A
N
T
P
G
G-ETH
G
P
H
D
CCG-RUMBA
DVI
F
I
R
E
W
I
R
E
C
O
M
D
V
I
2
USB
A
N
T
P
G
G-ETH
G
P
H
D
B
CCI-RAP
Dual RS-232
CCIRAP
CCG-RUMBA
DVI
F
I
R
E
W
I
R
E
C
O
M
B
CCI-RAP
DVI/RS-232
CCG-RUMBA w. CCI-RAP
© EKF
-28-
ekf.com
CCJ-RHYTHM Mezzanine Module
Optionally the CCG-RUMBA can operate as system slot controller in a CompactPCI Express (CPCIe)
system, if it is complemented with the CCJ-RHYTHM mezzanine card. The CCJ is equipped with a
powerful PCI Express packet switch engine, which provides the downstream links required by a CPCIe
4-link configuration backplane. The CCJ-RHYTHM must be mounted on top of the CCG-RUMBA,
which results in a 8HP building block, suitable for a CPCI backplane with rightmost aligned system
slot. While the CPCI backplane system slot matches the CCG-RUMBA CompactPCI CPU board, the
CCJ-RHYTHM is positioned on the leftmost aligned system slot of a CompactPCI Express backplane.
With both backplanes present in a rack, the resulting system is a hybrid solution which allows to
combine CPCI peripheral boards (low cost, broad range) with CPCIe peripheral cards (high throughput
as required e.g. for connectivity and storage purposes). EKF offers also a heterogeneous backplane,
which integrates card slot connectors for both busses, CPCI and CPCIe, on a single PCB.
CPCI System Slot
CPCIe System Slot
XP4
XP4
XP4
Type 2
Type 2
Type 2
XP1
XJ2
XP3
P1
XP3
P2
XJ3
P2
XP3
J2
XJ4
CompactPCI Backplane
CompactPCI Express Backplane
4-Link Configuration
© EKF
ekf.com
CCG-RUMBA/CCJ-RHYTHM in a Hybrid System CPCI/CPCIe
As an option, an on-board IEEE 1394 (FireWire) controller is available (dual port PHY, 2 front panel
receptacles 400Mbps). In addition, the CCJ-RHYTHM can be provided with a secondary DVI-D video
connector and legacy functions, such as RS-232 serial I/O (COM ports). Furthermore the CCJ can carry
a 2.5-inch PATA hard disk.
© EKF
-29-
ekf.com
Major Stuffing Options CCJ-RHYTHM
PCI Express
24-Lane PCI Express 6-port packet switch engine, 1 upstream link x 4 to
CCG-RUMBA, 4 downstream links x 4 to CompactPCI Express backplane,
1 downstream link to on-board 1394 controller
CompactPCI Express
Backplane
CPCIe system slot controller, 4x4 PCIe links/lanes
DVI-2 or COM-A
Either secondary DVI-D video output connector and single USB receptacle,
or RS-232E COM port connector (male D-Sub 9) and dual USB receptacle
USB
Front panel connector
IEEE 1394
On-board PCIe IEEE 1394a (FireWire) controller, 2-port PHY
COM-B
Second RS-232E COM port connector (male D-Sub 9)
FWH2
TPM1.2
USB Flash
Option pin header for USB Flash disk module (e.g. M-Systems uDOC
MD1665, SimpleTech SLUFDM, Intel Z-U130)
2.5-Inch HDD
Parallel ATA (Ultra ATA/100) disk drive option
CCG-RUMBA & CCJ-RHYTHM on a Hybrid Backplane
© EKF
-30-
ekf.com
Front Panel Options CCJ-RHYTHM
CCGRUMBA
C
O
M
D
V
I
USB
P
G
G-ETH
G
P
H
D
CCG-RUMBA
DVI
U
S
B
F
I
R
E
W
I
R
E
A
I
© EKF
CCJRHYTHM
C
O
M
CCGRUMBA
CCJRHYTHM
D
V
I
D
V
I
I
2
USB
P
G
G-ETH
G
P
H
D
B
CCG-RUMBA
DVI
CCJ-RHYTHM
Dual RS-232
-31-
U
S
B
F
I
R
E
W
I
R
E
C
O
M
B
CCJ-RHYTHM
DVI
ekf.com
CCJ-RHYTHM/CCG-RUMBA
Backplane Connector Suite
Hybrid Backplane CPCI & CPCI Express
© EKF
-32-
ekf.com
CCK-MARIMBA Mezzanine Module
As an option, the CCG-RUMBA is available together with the CCK-MARIMBA mezzanine expansion
card (side board). The CCK-MARIMBA is mainly a carrier board to accommodate a PMC/XMC module.
Furthermore the CCK-MARIMBA can be equipped with the C20-SATA storage module in addition,
which is populated with up to two 2.5-inch SATA hard drives, either individually addressable or
configured as RAID. The CCK-MARIMBA/C20-SATA must be mounted on top of the CCG-RUMBA,
which results in a 8HP or higher building stack, suitable for CPCI backplanes with a rightmost aligned
system slot (while the CPCI backplane system slot matches the CCG-RUMBA, the CCK-MARIMBA
mezzanine board is usually positioned outside the CPCI backplane).
Major Stuffing Options CCK-MARIMBA
PMC
On board PCIe to PCI bridge, 32bit/33MHz PMC
PMX
PMX according to Vita.42, two PCIe lanes
FWH2
TPM1.2
USB Flash
Option pin header for USB Flash disk module (e.g. M-Systems uDOC MD1665,
SimpleTech SLUFDM, Intel Z-U130)
SATA Storage
CCG-RUMBA w. CCK-MARIMBA Side Board
© EKF
-33-
ekf.com
Front Panel Options CCK-MARIMBA
CCGRUMBA
CCKMARIMBA
X
M
C
USB
P
G
P
M
C
G-ETH
M
E
Z
Z
A
N
I
N
E
G
P
D
V
I
I
H
D
CCG-RUMBA
DVI
© EKF
CCKMARIMBA
-34-
ekf.com
CCL-CAPELLA Mezzanine Module
Available as a mezzanine add-on expansion
board to the CCG-RUMBA and successor CPU
cards, the CCL-CAPELLA provides a number of
additional I/O functions. First of all, the CCLCAPELLA is a powerful Ethernet networking
machine, with up to four independent low
power Gigabit Ethernet controllers. Each GbE
port can be individually routed either to a front
panel jack, or the rear I/O connector, by
software controlled switches (BIOS setup).
The CCL-CAPELLA will be attached on top of the
CPU carrier board, and typically shares its front
panel with the host carrier (usually 8HP front
panel width in total). Interconnection between
the CCL-CAPELLA I/O module and the CPU
carrier board is achieved by two expansion
connectors, which comprise the PCIe (PCI
Express x 4) and LPC (Low Pin Count) interfaces.
As an option, the CCL-CAPELLA is available with
a mezzanine module (C20-SATA), which
accommodates one or two 2.5-inch SATA hard
disk drives (RAID option). Additionally, a
CompactFlash card adapter (C17-CFA) can be
mounted on bottom of the CCL-CAPELLA. As an
alternative, a top mount 1.8-inch storage
module (C30-PATA) is available, for HDD or SSD
usage. As another option, up to two USB Flash
drive modules can be accommodated, top and
bottom.
The additional SATA/PATA controller is useful
for attachment of mass-storage devices, either
on-board mounted, or externally (by cable or
via rear I/O).
The optional FireWire ports are practical e.g. for
vision systems with mixed 1394a and GbE type
cameras, and is especially useful for quality-ofservice demanding and isochronous
applications.
The CCL-CAPELLA is best suited for demanding
networking I/O applications, e.g. routers,
gateways, vision systems, or network fabric.
Maximum throughput is achieved through PCI
Express technology. Combined with the two
GbE ports available on the CPU carrier board,
six individual networking interfaces altogether
are provided for high performance Ethernet
communication.
Furthermore the CCL-CAPELLA is equipped with
a SIO, which provides legacy I/O ports, such as
serial, parallel, KB/MS (all available across rear
I/O). A secondary Firmware Hub can be
configured as alternate- or backup-BIOS.
Another option available is the Trusted Platform
Module according to TPM 1.2 for safety critical
applications.
Major Stuffing Options CCL-CAPELLA
GbE
Up to 4 PCIe Gigabit Ethernet controllers
IEEE1394a
PCIe FireWire controller
SATA
TPM1.2
Option Trusted Platform Module (e.g. Infineon SLB 9635)
USB SSD
Option pin header for USB Flash disk module (e.g. STEC SLUFDM, Intel
Z-U130)
© EKF
-35-
ekf.com
Front Panel Options CCL-CAPELLA
CCGRUMBA
CCLCAPELLA
1394
D
V
I
I
USB
P
G
G-ETH
G
P
H
D
G-ETH
CCG-RUMBA
DVI
CCLCAPELLA
CCG-RUMBA w. CCL-CAPELLA Side Board
© EKF
-36-
ekf.com
CCO-CONCERT Mezzanine Module
Available as a mezzanine add-on expansion
board (aka side board) to the CCG-RUMBA and
successor CompactPCI® CPU cards, the
CCO-CONCERT provides a number of frequently
required I/O functions. In addition, the user can
choose between several SATA and USB based
mass storage options.
For dual screen applications (in addition to the
primary DVI connector on the CPU carrier
board), the CCO-CONCERT can be equipped
with either a SDVO to PanelLink transmitter (for
digital video output), or a SDVO to VGA DAC
(for analog video output), with both signal
types available on the secondary front panel DVI
connector.
The on-board HD Audio codec is useful e.g. for
passenger information systems. Analog inputs
and outputs are available from 3.5mm stereo
jacks situated in the front panel, each
individually configurable by driver software as
microphone in, line in, headphones out or line
out. As an option, a D-SUB connector provides
also S/PDIF digital audio along with additional
analog lines.
Furthermore the CCO-CONCERT is equipped
with a SIO, which provides legacy I/O ports,
such as serial (UART) and PS/2 keyboard/mouse
interfaces. Two RS-232E COM port connectors
are mounted in the front panel.
A secondary Firmware Hub can be configured
as alternate- or backup-BIOS. Another option
available is the Trusted Platform Module
according to TPM 1.2 for safety critical
applications.
The CCO-CONCERT can be equipped with up to
three RAID0/1 capable PCIe dual channel SATA
controllers, useful for attachment of massstorage devices, either on-board mounted, or
externally (by cable or via rear I/O).
CCO-CONCERT
© EKF
-37-
ekf.com
CCG-RUMBA w. CCO-CONCERT (12HP FP)
CCG-RUMBA w. CCO-CONCERT
© EKF
-38-
ekf.com
C13-RD Front Panel CompactFlash Slot
Available as a mezzanine expansion option to
the CCD-CALYPSO CPU card, the C13-RD is
provided with a CF Card socket for front panel
insertion.
The overall front panel width available for the
entire assembly may be either 6HP (smallest) or
8HP (standard). The C13-RD uses the J-IDE
connector of the CPU card.
C13-RD (6HP Version)
© EKF
-39-
ekf.com
C23-SATA Mezzanine Module
The C23-SATA is a mezzanine side board,
equipped with a PCI Express to SATA/PATA
controller. Two SATA connectors and a
master/slave IDE header are provided for
attachment of system internal storage devices.
As an option, the C23-SATA can be stuffed with
a TPM 1.2 (Trusted Platform Module) compliant
encryption chip. Also as an option available is
an audio codec (AC'97 compliant).
The C23-SATA will be attached on top of the
CPU board, and shares its front panel typically
with the host CPU carrier board (8HP front
panel width in total).
The front panel contains three COM port
connectors RS-232. One port can be configured
as RS-485.
CCD-CALYPSO w. C23-SATA Side Board
© EKF
-40-
ekf.com
Coating
For extremely rugged environments, the CCG-RUMBA is available also coated, on customers request
(see photos below).
CCG-RUMBA Coated
CCG-RUMBA Coated
© EKF
-41-
ekf.com
Ordering Information
Ordering No.
Short Description
CCG-1RD-RUMBA
3U/4HP, Core™ 2 Duo U7500 1.06GHz FSB 533MHz 2MB L2 cache, dual socket DDR2
SO-DIMM up to 4GB, DVI-I dual screen, dual GB-ETH, 7 x USB, 1 x PATA, 3 x SATA-2, 4 x
PCIe, CF card slot, suitable for rear I/O across J2
<
targeted for low power applications
CCG-2RD-RUMBA
Similar to CCG-1, Core™ 2 Duo U7600 1.2GHz FSB 533MHz 2MB L2 cache
<
targeted for low power applications
CCG-4RD-RUMBA
Similar to CCG-1, Core™ 2 Duo L7500 1.6GHz FSB 800MHz 4MB L2 cache
<
targeted for general purpose applications
CCG-8RD-RUMBA
Similar to CCG-1, Core™ 2 Duo T7500 2.2GHz FSB 800MHz 4MB L2 cache
<
targeted for dual core performance applications
C23-SATA
Side board, PCIe to SATA/PATA controller, 2 x RS-232, 1 x RS-232/RS-485, USB SSD, option
audio codec AC'97, option TPM module
CCE-PUNK
Side board, 2 x 1394a FireWire, 2 x USB2.0, 2 x RS-232, option on-board hard disk
CCH-MARIACHI
Side board, HD audio codec (Azalia), option TPM 1.2, DVI-D digital video, analog audio
(option digital), RS-232 (COM), option USB, option on-board hard disk
CCI-RAP
Side board, 2 x PCI Express Mini Card sockets (e.g. WLAN, GSM/HSDPA, Robson Turbo
Memory), USB Flash Disk option, DVI-D, 2 x FireWire, on-board SATA hard disk option (1 or 2
drives), option TPM 1.2
CCJ-RHYTHM
Side board, System Slot for CompactPCI Express backplanes, 24-port PCI Express packet
switch, DVI-D, 1 x USB, 2 x FireWire, 1 x RS-232 (COM), on-board hard disk option, option
TPM 1.2
CCK-MARIMBA
Side board, PMC/XMC module socket
CCL-CAPELLA
Side board, quad Gigabit Ethernet Controller, USB Flash Disk option, FireWire, on-board
SATA hard disk option (1 or 2 drives), option TPM 1.2
CCO-CONCERT
Side board, HD Audio, 2-4 x RS-232, secondary DVI-I (option), several on-board SATA drive
options 1.8-inch and 2.5-inch (up to 2 drives), USB Flash Disk option, option TPM 1.2
CCT-RIO
Rear I/O transition module for with SATA connectors
CCG-*R*-RUMBA: suitable for rear I/O across J2
CCG-*X*-RUMBA: suitable for 64-bit CPCI J2/P2 backplane
CCG-**D-RUMBA: DVI-I video connector
CCG-**V-RUMBA: VGA video connector
For custom specific configurations please mail to sales@ekf.de
© EKF
-42-
ekf.com
© EKF
-43-
ekf.com
© EKF
-44-
ekf.com
© EKF
-45-
ekf.com
Industrial Computers Made in Germany
boards.
EKF Elektronik GmbH
Philipp-Reis-Str. 4
59065 Hamm
Germany
systems.
solutions.
Phone +49 (0)2381/6890-0
Fax +49 (0)2381/6890-90
Internet www.ekf.com
E-Mail sales@ekf.com

CCG-RUMBA • Core™ 2 Duo CompactPCI ® CPU

Transcription

Similar documents

User Guide

Product Information

User Guide - Meilhaus Electronic

Le scaffalature metalliche e i soppalchi Scaffalature metalliche

Sprint AIR - Veterinary X-rays

Efficient Distributed Linear Classification Algorithms via the

USER MANUAL for USB2.0 Data-Link/ Bridge-Network

Cable Management System - Custom Products and Services

- Hardware

Minute - bronzan.net

Performance, Quality, Design

GET A $25 BONUS @ Party Poker

Computer accessories 2013

- Motherboards.org

computer - Vivanco

Computer Connections

stream your

Arun Shukla, Puneet Kumar Dept. of Mechanical, Industrial

Setup Guide

reviews - Hardware

The PC Engineer`s Reference Book - Learn, learn, and once again