Register of Mining Standards - FABERG Normenausschuss Bergbau

Transcription

Register of Mining Standards
dated 2015-12
Published by
FABERG Normenausschuss Bergbau
im DIN Deutsches Institut für Normung e.V.
Contact
Hans Georg Blasgude
blasgude@faberg.de
Page 1 of 44
Foreword
Normenausschuss Bergbau (FABERG) is an agency of DIN Deutsches Institut für Normung e.V., Berlin. As a joint
establishment of the German mining industry, it is supported by Vereinigung Rohstoffe und Bergbau e.V., Berlin and managed
by a governing body. From a management and staff point of view, it is associated with DMT DeutscheMontanTechnologie für
Rohstoff, Energie, Umwelt e.V. of Essen.
FABERG is responsible for national standardisation in the field of mining and acts as a representative for this field in European
(CEN) *) and international (ISO) **) standardisation efforts, supporting the introduction of standards in its specialised field for
any practice affected by these and is instrumental in establishing the German standards system.
An association representing the interests of the mining industry was formed as early as at the end of the 1800s – as a joint
effort of mines in the German Ruhr area – also dealing with issues of standardisation and recommending to its member
companies the use of specific pipes and underground rail systems.
After World War I, a committee was formed, dealing with standardisation on behalf of the coal mining industry in the German
Rhineland and Westphalia. It was realised at an early date that standardisation involving the entire mining industry would be
more effective and useful. This lead to the foundation of Fachnormenausschuss für den Bergbau (FaBerg) on November 28th,
1922 at Hannover.
Whereas during the first years of FABERG’s existence, dimensional and type standards were primarily set up, these were
increasingly followed by quality and demand-based standards. Personal safety equipment, too, was subject to standardisation
at an early date.
In 1955, during the ISO General Assembly at Stockholm, the foundation of a “Mining” technical committee - ISO/TC 82 – was
resolved, management of which was transferred to FABERG. In addition to this, FABERG is responsible for German
representation in ISO/TC 27 "Solid Mineral Fuels".
Within the scope of its CEN work delegated by the EU, FABERG was allocated the CEN/TC 196/WG 3 "Hydraulically Powered
Support“ and CEN/TC 305/WG 5 "Equipment and Protective Systems for Mining" Secretariat.
FABERG co-operates with other standards committees of DIN, CEN and ISO at national, European and international level, in
order to represent the interests of the mining industry.
The Register of Standards comprises ISO standards of TC 27 "Solid Mineral Fuels" and of TC 82 "Mining".
The register also includes Operating Recommendations for Mining (Bergbau-Betriebsblätter). These are recommendations set
up by professionals, based on the same principles, which are mandatory for wording DIN standards. Users of these
recommendations are subject to examining whether any arrangements recommended in these are adequate. BergbauBetriebsblätter are published by DMT DeutscheMontanTechnologie für Rohstoff, Energie, Umwelt e.V. Bergbau-Betriebsblätter
may be ordered from DMT DeutscheMontanTechnologie für Rohstoff, Energie, Umwelt e.V., FABERG, Normenausschuss
Bergbau, Wilhelmstraße 98, 44649 Herne, Telefon +49 2325 5832456.
The Standards Inspection Office of DIN in FABERG is available for inspection of any national DIN standards. Research work
may be conveniently performed through the Perinorm database of BSI, AFNOR and DIN and ISO/IEC, CEN/CENELEC
standards.
Opening times of Standards Inspection Office (Normenauslegestelle):
Monday to Friday: 8.00 a.m. to 12.00 a.m. and 1.00 p.m. to 3.30 p.m.
--------*) CEN = Comité Européen de Normalisation
**) ISO = International Organization for Standardization
Page 2 of 44
The numbers after the titles of DIN standards and DIN drafts in brackets are price
groups (dated 2014-01-01); they correspond with the following prices (paper version):
Preisgr. EUR
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
16,70
24,60
24,60
24,60
34,90
42,40
49,50
57,00
64,10
71,10
78,30
85,80
92,70
99,80
107,10
113,20
118,80
124,20
Preisgr. EUR
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
Preisgr. EUR
130,20
135,90
142,10
147,50
153,00
159,30
164,50
170,40
176,60
182,40
188,00
193,50
198,90
217,80
233,00
252,20
265,80
293,10
37
38
41
42
51
52
320,30
347,40
369,80
391,90
430,50
496,60
Further information on prices you will get by DIN Deutsches Institut für Normung e.V.
in Berlin.
The numbers after the titles of "Bergbau-Betriebsblätter" in brackets are price groups
(dated 2014-01-01); they correspond with the following prices:
Group
1
2
3
4
5
EUR
7,70
10,50
13,10
15,70
21 60
Page 3 of 44
Register of Mining Standards 2015-12
FB Shaft 01
01 Shaft
NA 008-01-01 AA Shaft sinking
DIN 4930
06.89 Pipes for use in freezing shaft sinking; dimensions and technical delivery
conditions (5)
DIN 21151
11.09 Shaft sinking; pulleys for flat winding ropes; safety requirements and testing (8)
E DIN 21151
02.15 Shaft sinking - Pulleys for flat winding ropes - Safety requirements and testing
(8)
DIN 21164
08.15 Shaft sinking - Riders for winding kibbles - Safety requirements and testing (13)
DIN 21181-1
03.10 Shaft sinking Debris kibbles - Part 1: Debris kibbles with suspension hanger (12)
DIN 21181-2
03.10 Shaft sinking; debris kibbles - Part 2: Debris kibbles with suspension two-strand
chain set (9)
DIN 21186
03.13 Shaft sinking - Rope suspension gears for load hoisting in shafts (7)
DIN 21187
03.13 Shaft sinking - Chain suspension gears for load hoisting in shafts (6)
DIN 21194
12.99 Shaft sinking - Abutment for guide ropes - Safety requirements and testing (7)
DIN 21198
11.09 Shaft sinking - Shaft plumbs (6)
E DIN 21198
03.15 Shaft sinking - Shaft plumbs (7)
DIN 21500
11.01 Shaft sinking in mining - Design and dimensioning (12)
NA 008-01-02 AA Shaft transport
DIN 4118
06.81 Head frames and winding towers for mines; Design loads, calculation principles
and design principles (4) /FABERG co-author/
DIN EN 12385-1
01.09 Steel wire ropes - Safety - Part 1: General requirements; German version EN
12385-1:2002+A1:2008 (12) /FABERG co-author/
DIN EN 12385-2
06.08 Steel wire ropes - Safety - Part 2: Definitions, designation and classification;
German Version prEN 12385-2:2002/+A1:2008 (20) /FABERG co-author/
DIN EN 12385-2/B1
01.09 Steel wire ropes - Safety - Part 2: Definitions, designation and classification;
German Version prEN 12385-2:2002/+A1:2008, Corrigendum to DIN EN
12385.2:2008-06 /FABERG co-author/
DIN EN 12385-3/B1
01.09 Steel wire ropes - Safety - Part 3: Information for use and maintenance;
German version EN 12385-3:2004/+A1:2008, Corrigendem to DIN EN
12385.3:2008-06 /FABERG co-author/
DIN EN 12385-3
06.08 Steel wire ropes - Safety - Part 3: Information for use and maintenance;
German version EN 12385-3:2004/+A1:2008 (13) /FABERG co-author/
DIN EN 12385-6
05.04 Steel wire ropes - Safety - Part 6: Stranded ropes for mine shafts; German
version EN 12385- 6:2004 (12)
DIN EN 12385-7
02.03 Steel wire ropes - Safety - Part 7: Locked coil ropes for mine shafts; German
version EN 12835-7:2002 (9)
DIN 20400
01.90 Knuckle threads for the mining; threads with large load-bearing depth (6)
DIN 21258
10.07 Lubricants and impregnating compounds for friction hoist ropes in mining Safety requirements and testing (9)
DIN 21341
08.86 Wooden mine guides (6)
DIN 21346
11.89 Square head bolts for shaft guides (5)
DIN 21371
01.88 Rope attachments; assemblies (5)
DIN 21376-1
07.88 Guide shoes for shaft conveyances and counterweights with guide rollers in
mining (5)
DIN 21376-2
07.88 Guide shoes for shaft conveyances and counterweights with slide-ways in
mining (5)
DIN 21377
12.94 Steel railings for shaft conveyances in mining (5)
DIN 21381
01.88 Rope attachments; thimble connection plates for round ropes (5)
Page 4 of 44
FB Shaft 01
DIN 21382
01.88 Rope attachments; outer plates, inner plates (5)
DIN 21383
01.88 Rope attachments; pins (5)
DIN 21386
01.88 Rope attachments; thimbles for round ropes (5)
DIN 21388
01.88 Rope attachments; universal joints (5)
DIN 21389
01.88 Rope attachments; clamp thimbles (5)
DIN 21390
02.85 Thimbles for flat ropes (5)
DIN 22400
04.90 Control units of winding engines; hoists and winches for mining (5)
DIN 22405
05.90 Friction pulley linings for winches and winders in mining (5)
DIN 22406
10.86 Low speed Koepe winding machines with friction wheel, for shafts and drifts;
braking system calculation formulae (13)
DIN 22410
05.94 Winding rope pulleys for round ropes (10)
Page 5 of 44
FB Mine Support 02
02 Mine Support
NA 008-02-01 AA Strut support
DIN EN 1804-1
05.10 Machines for underground mines - Safety requirements for hydraulic powered
roof supports - Part 1: Support units and general requirements; German version
EN 1804-1:2001+A1:2010 (16)
DIN EN 1804-2
roof supports - Part 2: Power set legs and rams; German version EN 18042:2001+A1:2010 (16)
DIN EN 1804-3
roof supports - Part 3: Hydraulic control systems; German version EN 18043:2006+A1:2010 (15)
DIN 21546
08.90 Mine support; strut support; marking (3)
DIN 21549
03.88 Mine supports; powered walking supports; terminology (5)
DIN 21550
05.88 Mine support; roof bars for single props; testing, requirements (5)
DIN 21551
01.86 Mine support; roof bars single props; lengths (5)
DIN 21555
08.91 Mine support; graphical symbols for the open loop control of powered support (6)
DIN 21556
02.87 Mine support; valves for individual props; identification code (5)
DIN 21557
02.87 Mine support; yield valves for powered support; identification code (5)
DIN 21561
09.86 Mine support; head for single props; connecting dimensions (5)
NA 008-02-03 AA Roadway support
DIN 21319
02.89 Round pit timber; bolts (5)
DIN 21326
04.89 Sawn pit timber; boards and planks (5)
DIN 21327
02.89 Sawn pit timber; boards, planks and square-sawn timber for working platforms
(5)
DIN 21329
06.87 Cut pit timber; technical terms of delivery and quality (5)
E BB 21510
06.95 Verzugsmatten - Technische Anforderungen (2)
DIN 21521-1
07.90 Rock bolts for mining and tunnelling; terms (6)
DIN 21521-2
02.93 Rock bolts for mining and tunnel support; general specifications for steel-bolts;
tests, testing methods (7)
DIN 21522
07.72 Roof bolt plates for mining and tunnel support (4)
DIN 21530-1
05.03 Mine support - Part 1: General (5)
DIN 21530-2
05.03 Mine support - Part 2: Dimensions, designation and statical values (21)
E DIN 21530-2
01.16 Mine support - Part 2: Dimensions, designation and statical values (23)
DIN 21530-3
05.03 Mine support - Part 3: Requirements (10)
E DIN 21530-3
01.16 Mine support - Part 3: Requirements (10)
DIN 21530-4
05.03 Mine support - Part 4: Testing (10)
E DIN 21530-4
01.16 Mine support - Part 4: Testing (11)
DIN 21530-5
05.03 Mine support - Part 5: Marking of parts of mine support (6)
E DIN 21530-5
10.15 Mine support - Part 5: Marking of parts of mine support (6)
DIN 21531-1
07.90 Arch supports; arches B 5, 4 to B 20, 2 (5)
DIN 21531-2
07.90 Arch supports; arches B 21, 7 to B 63 (5)
Page 6 of 44
FB Extraction 03
03 Extraction
NA 008-03-01 AA Extracting and stowing
DIN EN 1552
09.03 Underground mining machines - Mobile extracting machines at the face - Safety
requirements for shearer loaders and plough systems; German version EN
1552:2003 (10) /FABERG co-author/
DIN 20012
04.89 Pneumatic stowing pipes (5)
DIN 20013
04.89 Sealings for pneumatic stowing pipes (5)
DIN 20097
07.68 Gears for coal ploughs and underground chain- conveyors; signs for gears (4)
/FABERG co-author/
DIN 20350
03.75 Protective clothing - General requirements; German version prEN 340:2000 (4)
/FABERG co-author/
Page 7 of 44
FB Tools 04
04 Tools
NA 008-04-01 AA Rock drilling/Hand tools
DIN 1197-1
06.90 Eyes for picks, oval; dimensions, requirements, testing (5)
DIN 1197-2
06.90 Pick eyes, oval; plug gauges (5)
DIN 6436
06.90 Pickaxes (5)
DIN 6437-1
06.90 Pickaxe handles; dimensions, requirements, testing (5)
DIN 6437-2
06.90 Pickaxe handles; gauges (5)
DIN 20109
06.90 Pickaxes, chisel and point ends (5)
DIN 20110
06.90 Beater-pickaxes (5)
DIN 20112
06.90 In triangular hand hoes (5)
DIN 20115
06.90 Miners axes (5)
DIN 20119
07.90 Trough shovel (5)
DIN 20120
07.90 Sand shovel (5)
DIN 20121
07.90 Digging shovel (5)
DIN 20123
07.90 Rimmed shovel (5)
DIN 20124
07.90 Pan shovel (5)
DIN 20125
07.90 Loading shovel (5)
DIN 20127
09.13 Garden tools - Non-motorized hand-held tools for using in soil - Spades (5)
/FABERG co-author/
DIN 20128
07.90 Shallow rimmed shovel (5)
DIN 20129
07.90 Plain shovel (5)
DIN 20135
07.90 Sledge hammer (5)
DIN 20136
07.90 Hand hammer (5)
DIN 20142
07.92 Hacksaws with steel frames and two handles (5)
DIN 20151
01.84 Gears for coal ploughs and underground chain- conveyors; signs for gears (4)
/FABERG co-author/
DIN 20152
03.89 Shovel and spade handels; types, dimensions, requirements, testing, marking
(5) /FABERG co-author/
DIN 20301
01.99 Rock drilling operations - Terminology, units, and symbols for use in formulae (9)
DIN 20302
02.74 Rock drilling operations - Terminology, units, and symbols for use in formulae
DIN 20311
11.02 Drill tubes with diameters exceeding 100 mm for large hole boring in mining (5)
DIN 20314
06.90 Screw threads for drill tubes will diameters exceeding 100 mm for large hole
boring in mining (5)
DIN 20316
11.12 Rock drilling - Thread connections for thin-walled rotary drilling equipment Dimensions, design (5)
DIN 20317
02.14 Rock drilling - Round thread connections for percussive drilling equipment Dimensions, design (4)
DIN 20351
08.15 Rock drilling - Wedge-shaped shank connections for rotary drilling equipment Dimensions, design (7)
E DIN 20352
09.15 Rock drilling - Square drive connection for rotary drilling - Dimensions, design (6)
E DIN 20353
10.15 Rock drilling - trapezoidal thread connection for percussive drilling Dimensions, design (5)
DIN 20361
04.10 Rock drilling - Chuck bushings - Connecting dimensions, material, design (4)
DIN 20367
04.10 Rock drilling - Round screw connections for rotary drilling equipment Dimensions, design (5)
Page 8 of 44
FB Tools 04
DIN 20369
09.89 Pick hammers; flat- and shearpick without and with shank (5)
DIN 20371
09.69 Hammer drilling; connecting tap for hammer drilling support (4) /FABERG coauthor/
DIN 20372
05.88 Rock drilling; water tube; connecting dimensions, material, finish (5)
DIN 20374
01.88 Pick hammers; gauges for picks (5)
DIN 20375
01.88 Pick hammers; round picks without shank (5)
DIN 20376
01.88 Pick hammers; round picks with shank (5)
DIN 20377
11.09 Rock drilling - Flush drills - Drill rod profiles, shanks and tapers (7)
DIN 20378
10.90 Drilling hammers; taper gauges for tapered connections of drill rods and bits (5)
DIN 20379-1
05.11 Rock drilling - Part 1: Tapered bits for percussive flush drilling (7)
DIN 20379-2
05.11 Rock drilling - Part 2: Bits with internal thread for percussive flush drlling (7)
DIN 24063
01.80 Operating elements (control devices) for pneumatic tools; terms, safety
requirements (4) /FABERG co-author/
DIN 68340
01.89 Timber handles for impact tools; technical specifications (5) /FABERG co-
Page 9 of 44
FB Transport 05
05 Transport
NA 008-05-01 AA Mine railways
DIN 5902
11.95 Fishplates for grooveless flat bottom rails dimensions - Steel types (10)
/FABERG co-author/
DIN 5904
11.95 Steel sleepers - Dimensions, static values, steel types (6) /FABERG co-author/
DIN 5906
11.95 Short clips for grooveless flat bottom rails - Dimensions, steel types (6)
/FABERG co-author/
DIN 5914
03.65 baseplate scrwes with rectangular head (4) /FABERG co-author/
DIN 20449
10.88 Points and crossovers for rail haulage roads in mines; standard types,
terminology (7)
DIN 20450
10.88 Simple underground track points; 20 m radius, 1 : 5 inclination; geometric
dimensions (5)
DIN 20452-1
10.88 Simple points for underground tracks with loose heel switch; 20 m radius, 1 : 5
inclination, 600 mm gauge; compilation (5)
DIN 20452-2
10.88 Simple points for underground tracks with spring switch blade; 20 m radius, 1 : 5
DIN 20453-1
10.88 Switches for simple underground track points with loose heel switch; 20 m
radius, 1 : 5 inclination, 600 mm gauge (5)
DIN 20453-2
10.88 Switches for simple underground track points with spring switch blade; 20 m
DIN 20454
10.88 Crossings for simple underground track points; 20 m radius, 1 : 5 inclination,
600 mm gauge (5)
DIN 20455
10.88 Check rail device for simple underground track points; 20 m radius, 1 : 5
inclination, 600 mm gauge (5)
DIN 20458
10.88 Simple crossovers for underground tracks; 20 m radius, 1 : 5 inclination;
geometric dimensions (5)
DIN 20460
dimensions (5)
DIN 20462-1
DIN 20462-2
DIN 20463-1
DIN 20463-2
DIN 20464
600 mm gauge (5)
DIN 20465
DIN 20468
DIN 20470
dimensions (5)
DIN 20472-1
DIN 20472-2
DIN 20473-1
Page 10 of 44
FB Transport 05
DIN 20473-2
DIN 20474
600 mm gauge (5)
DIN 20475
DIN 20478
DIN 20499
01.07 Rail haulage roads in mines - General rules (12)
DIN 20500
11.15 Underground mine railways - Track gauges and rails; Standard types and
selection (5)
DIN 20501
11.15 Underground mine railways - But strap Fl 30 for rail 30E1 (5)
DIN 20506
11.15 Underground mine railways - Clamping plates for securing rails onto steel
supports (5)
DIN 20548
07.90 Wheel sets for rail vehicles used in mines; rules for measuring (5)
DIN 20549
11.86 Track gauges for pit railways; definition and tolerances (5)
DIN 20550
07.90 Mine cars size small; components, main dimensions, design (5)
DIN 20551
01.12 Mine cars - front wall, casing, frame, buffer sheet (9)
DIN 20552
11.88 Small size lubs; bumpers, supporting beam (5)
DIN 20553
01.12 Wheel sets with taper roller bearings for mine cars; without springs (8)
DIN 20555
01.12 Wheel sets with taper roller bearings for mine cars; exterior spring suspension
(11)
DIN 20556
01.12 Wheel sets with taper roller bearings for mine cars; interior spring suspension (9)
DIN 20560
07.89 Mine cars; middle size; dimensions, design and construction (5)
DIN 20570
04.89 Mine cars; large size; dimensions, design and construction (5)
DIN 20575-1
10.03 Rail transport - Passenger cars for underground mining - Part 1: Requirements
(6)
DIN 20579-1
07.86 Buffer springs for mine cars; calculation (5)
DIN 20579-2
07.86 Buffer springs for mine cars; requirements (5)
DIN 20581
03.88 Mine cars; strap type coupling (5)
DIN 20583
11.95 Mine cars - Shackle coupling (5)
DIN 20586
01.12 Rail fastenings in mining for S 30E1 and 33E1 rails on wooden sleepers (8)
DIN 20600
11.15 Mine railways - Wheel profils for locomotives and cars (5)
DIN 20601
05.91 Mine cars; tyres for mine locomotives (5)
DIN 21325
02.12 Pit converted timber - Timber sleepers (5)
DIN 45635-52
05.86 Measurement of airborne noise emitted by machines; enveloping surface
method; mine diesel locomotives and mine road railers (5) /FABERG co-author/
DIN 45635-53
method; diesel traction trolleys (5) /FABERG co-author/
DIN 45635-54
method; mine trackless vehicles (5) /FABERG co-author/
DIN 45635-55
method; shunting trolleys with friction- wheel and/or gearwheel drive (5)
/FABERG co-author/
NA 008-05-02 AA Suspended monorails
DIN 20590
04.90 Securing devices on underframes used in mining (5)
DIN 20592-1
08.91 Suspended monorails for mining; transport boxes; dimensions and
requirements (5)
Page 11 of 44
FB Transport 05
DIN 20592-2
08.91 Suspended monorails for mining; attachment facilities for transport boxes;
dimensions and requirements (5)
DIN 20593-1
11.02 Monorails for mining - Rails - Part 1: Straight rails for profile I 140 E (7)
DIN 20593-2
11.02 Monorails for mining - Rails - Part 2: Curved rails and adapting rails for profile I
140 E (8)
DIN 20593-3
07.04 Monorails for minging - Rails - Part 3: Straight rails and rail-connections for
profiles I 140V and I 250 (11)
DIN 20593-4
04.07 Monorails for minging - Rails - Part 4: Curved rails and adapting rails for profiles
I 140 V and I 250 (12)
DIN 20594
08.91 Suspension claws for mining, for loads up to 30 kN; requirements and testing (7)
DIN 20597
04.15 Suspended monorails for mining - Toothed disc for roller fairleads - Dimensions,
materials (5)
DIN 20599
08.93 Suspended monorails for mining; rope positions, mounting devices, clearance
dimensions for bogies (5)
DIN 20619
08.93 Suspended monorails for mining; winding-drum with suspension hook;
dimensions and requirements (6)
DIN 20620-1
10.94 Force-guided tram-ways in mining - Part 1: Survey; structure and terms (5)
DIN 20620-2
10.94 Force-guided tram-ways in mining - Part 2: Monorails; structure and terms (6)
DIN 20620-3
10.94 Force-guided tram-ways in mining - Part 3: Free-steered machines; structure
and terms (6)
DIN 20622
04.15 Suspended-monorail transport systems for mining - Permissible loads for
suspensions and their abnutments and railprofile I 140 E (11)
DIN 20625-1
03.92 Capture-track rail installations in mining; bolted couplings for rope-hauled and
self-propelled rail installations; bolted coupling 30 (7)
DIN 20629-1
08.01 Suspended monorails for mining - Mounting regulations - Part 1: for cabledriven suspended monorails (7)
DIN 20629-2
04.15 Suspended monorails for mining - Mounting regulations - Part 2: For loco-driven
suspended monorails (13)
DIN 20629-3
08.01 Suspended monorails for mining - Mounting regulations - Part 3: Calculations (5)
DIN 20633
04.02 Overhead monorail installations for mining - Double-end fork turnbuckles (7)
DIN 20635
05.01 Monorails for mining - Suspensions shackles (6)
DIN 20636
06.01 Monorails for mining - Suspension claws - Requirements and testing (5)
DIN 20637
10.97 Monorails for mining - Tested round steel chains for suspensions - Tested, long
link (5)
NA 008-05-03 AA Belt conveyors
DIN EN ISO 252
01.08 Conveyor belts - Ply adhesion between constitutive eleents - Test methods (ISO
252:2007); German version EN ISO:2007 (8) /FABERG co-author/
DIN EN ISO 283
02.08 Textile conveyor belts - Full thickness tensile strength, elongation at break and
elongation at the reference load - Test method (ISO 283:2007); German
version EN ISO 283:2007 (9) /FABERG co-author/
E DIN EN ISO 283
10.14 Textile conveyor belts - Full thickness tensile strength, elongation at break and
elongation at the reference load - Test method (ISOIDIS 283:2014); German
version prEN ISO 283:2014 (9) /FABERG co-author/
DIN EN ISO 340
10.13 Conveyor belts - Laboratory scale flammability characteristics - Requirements
and test method (ISO 340:2013) German version EN ISO 340:2013 (8)
/FABERG co-author/
DIN EN ISO 505
04.00 Conveyor belts - Method for the determination of the tear propagation
resistance of textile conveyor belts (ISO 505:1999); German version EN ISO
Page 12 of 44
FB Transport 05
DIN EN ISO 583
03.08 Conveyor belts with a textile carcass - Total belt thickness and thickness of
constitutive elements - Method of test (ISO 583:2007); German version EN
ISO 583:2007 (9) /FABERG co-author/
DIN EN ISO 703
03.08 Conveyor belts - Transverse flexibility (troughability) - Test method (ISO
703:2007); German version EN ISO 703:2007 (8) /FABERG co-author/
DIN EN ISO 1120
04.13 Conveyor belts - Determination of strength of mechanical fastenings - Static test
method (ISO 1120:2012); German version EN ISO 1120:2012 (8) /FABERG coauthor/
DIN EN 1554
10.12 Conveyor belts - Drum friction testing; German version EN 1554:2012 (9)
/FABERG co-author/
DIN EN ISO 2842
04.13 Conveyor belts - Electrical conductivity - Specification and test method (ISO
284:2012); German Version EN ISO 284:2012 (8) /FABERG co-author/
DIN EN ISO 7590
03.10 Steel cord conveyor belts - Methods for the determination of total thickness and
cover thickness (ISO 7590:2001); German version EN ISO 7590:2001 (8)
/FABERG co-author/
DIN EN ISO 7622-1
11.13 Steel cord conveyor belts - Longitudinal traction test - Part 1: Measurement of
elongation (ISO 7622-1:2013); German version EN ISO 7622-1:2013 (6)
/FABERG co-author/
DIN EN ISO 7622-2
tensile strength (ISO 7622-2:1984); German version EN ISO 7622-2:1995 (6)
/FABERG co-author/
E DIN EN ISO 7622-2
tensile strength (ISO/DIS 7622-2:2014); German version prEN ISO 76222:2014 (7) /FABERG co-author/
DIN EN ISO 7623
E DIN EN ISO 7623
08.97 Steel cord conveyor belts - Cord-to-coating bond test - Initial test and after
thermal treatment (ISO 7623:1996); German version EN ISO 7623:1997 (6)
/FABERG co-author/
10.15 Steel cord conveyor belts - Cord-to-coating bond test - Initial test and after
thermal treatment (ISO/FDIS 7623:2015); German and English version FprEN
DIN EN ISO 8094
11.13 Steel cord conveyor belts; Adhesion strength test of the cover to the core layer
(ISO 8094:2013); German version EN ISO 8094:2013 (6) /FABERG co-author/
DIN EN ISO 9856
11.12 Conveyor belts - Determination of elastic and permanent elongation and
calculation of elastic modulus (ISO 9856:2003 + Amd 1:2012); German version
EN ISO 9856:2003 + A1:2012 (10) /FABERG co-author/
DIN EN 12881-1
10.15 Conveyor belts - Fire simulation flammability testing - Part 1: Propane burner
tests; German version EN 12881-1:2014 (16) /FABERG co-author/
DIN EN 12881-2
10.09 Conveyor belts - Fire simulation flammability testing - Part 2: Large scale fire
test; German version EN 12881-2:2005+A1:2008 (8) /FABERG co-author/
DIN EN 12882
11.15 Conveyor belts for general purpose use - Electrical and flammability safety
requirements; German version EN 12882:2015 (10) /FABERG co-author/
DIN EN 13827
07.04 Steel cord conveyor belts - Determination of the lateral and vertical
displacement of steel cords; German version EN 13827:2003 (7) /FABERG coauthor/
DIN EN ISO 14890
06.13 Conveyor belts - Specification for rubber or plastics-covered conveyor belts of
textile construction for general use (ISO 14890:2013); German version EN ISO
DIN EN 14973
12.09 Conveyor belts for use in underground installations - Electrical and flammability
safety requirements; German version EN 14973:2006+A1:2008 (11) /FABERG
co-author/
E DIN EN 14973
07.14 Conveyor belts for use in underground installations - Electrical and flammability
safety requirements; German version prEN 14973:2013 (11) /FABERG coauthor/
DIN 15207-1
10.00 Continuous mechanical handling equipment - Idlers for belt conveyors - Main
dimensions of idlers for belt conveyors for bulk material (5) /FABERG co-author/
Page 13 of 44
FB Transport 05
DIN EN ISO 15236-1
04.06 Steel cord conveyor belts - Part 1: Design, dimensions and mechanical
requirements for conveyor belts for general use (ISO 15236-1:2005); German
version EN ISO 15236-1:2005 (12) /FABERG co-author/
DIN EN ISO 15236-2
09.04 Steel cord conveyor belts - Part 2: Preferred belt types (ISO 15236-2:2004);
German version EN ISO 15236-2:2004 (8) /FABERG co-author/
DIN EN ISO 15236-3
04.08 Steel cord conveyor belts - Part 3: Special safety requirements for belts for use
in underground installations (ISO 15236-3:2007); German version EN ISO
15236-3:2007 (11) /FABERG co-author/
DIN EN ISO 15236-4
09.04 Steel cord conveyor belts - Part 4: Vulcanized belt joints (ISO 15236-4:2004);
DIN EN ISO 16851
09.13 Textile conveyor belts - Determination of the net length of an endless (spliced)
conveyor belt (ISO 16851:2012); German version EN ISO 16851:2013 (6)
/FABERG co-author/
DIN 22101
12.11 Continuous conveyors - Belt conveyors for loose bulk materials - Basis for
calculation and dimensioning (English translation) (21)
DIN 22101
12.11 Continuous conveyors - Belt conveyors for loose bulk materials - Basis for
calculation and dimensioning (21)
DIN 22102-1
01.14 Conveyor belts with textile plies for bulk goods - Part 1: Dimensions,
specifications, marking (7) /FABERG co-author/
DIN 22102-2
01.14 Conveyor belts with textile plies for bulk goods - Part 2: Testing (6) /FABERG coauthor/
DIN 22102-3
01.14 Conveyor belts with textile plies for bulk goods - Part 3: Permanent joints (9)
/FABERG co-author/
DIN 22107
08.84 Continous mechanical handling equipment; idler sets for belt conveyors for
loose bulk materials; principal dimensions (5) /FABERG co-author/
DIN 22109-1
03.15 Conveyor belts with textile plies for coalmining - Part 1: Monoply belts for
underground applications - Dimensions, requirements (6)
DIN 22109-2
03.15 Conveyor belts with textile plies for coalmining - Part 2: Rubber-belts with two
plies for underground applications - Dimensions, requirements (6)
DIN 22109-4
03.15 Conveyor belts with textile plies for coalmining - Part 4: Rubber-belts with two
plies for above ground applications; Dimensions, requirements (6)
DIN 22109-5
02.88 Conveyor belts with textile plies for coalmining; branding (5)
DIN 22109-6
12.03 Conveyor belts with textile plies for coalmining - Part 6: Testing (6)
E DIN 22109-6
10.15 Conveyor belts with textile plies for coalmining - Part 6: Testing (7)
DIN 22110-2
10.97 Testing methods for conveyor belt joints - Part 2: Endurance running tests,
determination of running time of belt joints at conveyor belts with textile plies (5)
DIN 22110-3
04.15 Testing methods for conveyor belt joints - Part 3: Determination of time strength
for conveyor belt joints (dynamical testing method) (8)
DIN 22111
11.07 Belt conveyors for underground coal mining - Light construction (11)
DIN 22112-1
12.10 Belt conveyors for underground coal mining - Idlers - Part 1: Dimensions (6)
DIN 22112-2
12.10 Belt conveyors for underground coal mining - Idlers - Part 2: Requirements (5)
DIN 22112-3
03.96 Belt conveyors for underground coalmining - Idlers - Part 3: Testing (7)
DIN 22114
12.10 Belt conveyors for underground coalmining - Heavy construction (12)
DIN 22115
10.03 Belt conveyors for underground coalmining; Coating on idlers; Requirements
and testing (7)
DIN 22116
10.03 Belt conveyors for underground coal mining - Pressure rollers DN 159 Dimensions, requirements, marking (6)
DIN 22117
02.88 Conveyor belts for coalmining; determination of the oxygen index (6)
DIN 22120
04.05 Elastomere scraper plates for belt conveyors in hard coal mines (6)
DIN 22121
04.15 Conveyor belts with textile plies for coalmining - Permanent joints for belts with
one or two plies - Dimensions, requirements, marking (7)
Page 14 of 44
FB Transport 05
DIN 22122
10.03 Continous mechanical handling equipment - Troughability of conveyor belts Determination of that portion of width of conveyor belting in contact with idlers,
requrements, testing (6)
DIN 22123
10.12 Conveyor belts - Indentation rolling resistances of conveyor belts related to
beltwidth - Requirements, testing (8)
DIN 22129-1
02.88 Steel cord conveyor belts for underground coalmining; dimensions,
requirements (6)
DIN 22129-2
02.88 Steelcord conveyor belts for underground coalmining; marking (5)
DIN 22129-3
02.88 Steelcord conveyor belts for underground coalmining; testing (6)
DIN 22129-4
08.15 Steelcord conveyor belts for use in underground coal mining - Belt joints - Part
4: Dimensions, requirements (8)
DIN 22131-3
11.88 Steelcord conveyor belts for hoisting and conveying; testing (5)
E DIN 22131-3
09.15 Steelcord conveyor belts for hoisting and conveying; Part 3: Testing (6)
DIN EN ISO 22721
01.10 Conveyor belts - Specification for rubber- or plastics-covered conveyor belts of
textile construction for underground mining (ISO 22721:2007); German version
EN ISO 22721:2007 (11) /FABERG co-author/
DIN 53530
02.81 Testing of organic materials; Separation test on fabric plies bonded together (5)
/FABERG co-author/
NA 008-05-05 AA Components for chain conveyors
DIN 763
12.90 Tested, non-calibrated, long-link round steel chains (5) /FABERG co-author/
DIN 8175
02.80 Conveyor chains; bush conveyor chains, heavy type (4) /FABERG co-author/
DIN 8176
01.80 Conveyor chains; bush conveyor chains for haulage systems (4) /FABERG coauthor/
DIN EN 12321
07.09 Underground mining machinery - Specification for the safety requirements for
armoured face conveyors; German version EN 12321:2003+A1:2009 (12)
DIN 22200
05.94 Continous mechanical handling equipment; idler sets for belt conveyors for
loose bulk materials; principal dimensions (5) /FABERG co-author/
BB 22249
12.72 Schmiernippel für den Bergbau (2)
DIN 22252
07.12 Round steel link chains for use in continuous conveyors and winning equipment
in mining (11)
DIN 22253
03.08 Chain connectors - Shackle type connector units - Dimensions, requirements,
testing (12)
DIN 22255
05.12 Flat link chains for use in continuous conveyors in mining (12)
DIN 22256
10.02 Chain sprockets for chain conveyors and coal winning equipment - Dimensions,
requirements, testing (11)
DIN 22256
10.02 Chain sprockets for chain conveyors and coal winning equipment - Dimensions,
requirements, testing (English translation)
DIN 22257
06.90 Scraper bars for chain conveyors; outboard chain assembly; dimensions,
requirements, testing (5)
DIN 22258-1
05.12 Chain connectors - Part 1: Flat type connectors (10)
DIN 22258-2
08.03 Chain connectors - Part 2: Kenter type connectors (English translation)
DIN 22258-2
09.15 Chain connectors - Part 2: Kenter type connectors (11)
DIN 22258-3
05.12 Chain connectors - Part 3: Block type connectors (10)
DIN 22259
05.07 Flightbars for use in chain conveyors in mining (10)
NA 008-05-06 AA Pipe systems
DIN 20002-1
11.89 Pipelines for mining; steel tubes with loose flanges and plain collars; nominal
pressure 10 (5)
DIN 20002-2
11.89 Pipelines for mining; steel tubes with loose flanges and collars; projection and
recess; nominal pressure 6 (5)
Page 15 of 44
FB Transport 05
DIN 20002-3
11.89 Pipelines for mining; steel tubes with loose flanges and plain collars; nominal
pressure 40 (5)
DIN 20003-1
09.87 Steel tubes for mining; fittings with loose flanges and plain collars; nominal
pressure 10 (7)
DIN 20003-2
09.87 Steel tubes for mining; fittings with loose flanges and plain collars, projection
and recess; nominal pressure 6 (7)
DIN 20003-3
09.87 Steel tubes for mining; fittings with loose flanges and plain collars; nominal
pressure 40 (6)
DIN 20004-1
12.00 Steel tubes for mining - Part 1: Interpose rings rated for PN 10 and PN 40 (6)
DIN 20004-2
12.00 Steel tubes for mining - Part 2: Wedge rings rated for PN 10 and PN 40 (5)
DIN 20006
09.89 Pipeline for mining; sealings for steel tubes according to DIN 20002 and fittings
according to DIN 20003 (5)
DIN 20042
08.01 Watervalve, nominal pressure 40 - Dimensions and requirements (5)
BB 20065-1
02.78 Kunststoff-Rohrleitungen - Richtlinien für die Verlegung - Thermoplastische
Kunststoffe (2)
BB 20065-2
02.78 Kunststoff-Rohrleitungen - Richtlinien für die Verlegung - Mitgeltende Normen
(2)
DIN 24251
08.73 Multistage centrifugal pumps; mine drainage pumps, with pump total head up to
1000 m at speed of rotation 1500 l/min (4) /FABERG co-author/
NA 008-05-07 AA Hose assemblies
DIN EN 853
02.97 Rubber hoses and hose assemblies - Wire braid reinforced hydraulic type Specification; German version EN 853:1996 (7) /FABERG co-author/
E DIN EN 853
05.13 Rubber hoses and hose assemblies - Wire braid reinforced hydraulic type Specification; German version prEN 853:2013 (11) /FABERG co-author/
DIN EN 854
02.97 Rubber hoses and hose assemblies - Textile reinforced hydraulic type Specification; German version EN 854:1996 (7) /FABERG co-author/
E DIN EN 854
05.13 Rubber hoses and hose assemblies - Textile reinforced hydraulic type Specification; German version prEN 854:2013 (11) /FABERG co-author/
DIN EN 856
02.97 Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced
hydraulic type - Specification; German version EN 856:1996 (7) /FABERG coauthor/
E DIN EN 856
05.13 Rubber hoses and hose assemblies - Rubber-covered spiral wire reinforced
hydraulic type - Specification; German version prEN 856:2013 (11) /FABERG
co-author/
DIN EN 857
02.97 Rubber hoses and hose assemblies - Wire braid reinforced compact type for
hydraulic applications - Specification; German version EN 857:1996 (6)
/FABERG co-author/
E DIN EN 857
05.13 Rubber hoses and hose assemblies - Wire braid reinforced compact type for
hydraulic applications - Specification; German version prEN 857:2013 (10)
/FABERG co-author/
DIN EN ISO 1402
04.10 Rubber and plastic hoses and hose assemblies - Hydrostatic testing (ISO
DIN EN ISO 7751
12.11 Rubber and plastics hoses and hose assemblies - Ratios of proof and burst
pressure to maximum working pressure - Amendment 1 (ISO 7751:1991 + Amd
1:2011); German version EN ISO 7751:1997 + A1:2011 (6) /FABERG co-author/
E DIN EN ISO 7751
10.15 Rubber and plastics hoses and hose assemblies - Ratios of proof and burst
pressure to maximum working pressure (ISO/DIS 7751:2015); German and
English version prEN ISO 7751:2015 (5) /FABERG co-author/
DIN EN ISO 8030
11.14 Rubber and plastics hoses - Method of test for flammability (ISO 8030:2014);
German version EN ISO 8030:2014 (8) /FABERG co-author/
DIN EN ISO 8031
04.10 Rubber and plastics hoses and hose assemblies - Determination of electrical
resistance and electrical conductivity (ISO 8031:2009); German version EN ISO
Page 16 of 44
DIN EN ISO 8033
E DIN EN ISO 8033
FB Transport 05
11.06 Rubber and plastics hoses - Determination of adhesion between components
(ISO 8033:2006); German version EN ISO 8033:2006 (10) /FABERG co-author/
10.15 Rubber and plastics hoses - Determination of adhesion between components
(ISO/DIS 8033:2015); German and English version prEN ISO 8033:2015 (11)
/FABERG co-author/
DIN EN ISO 8330
04.15 Rubber and plastics hoses and hose assemblies - Vocabulary (ISO
DIN 20018-1
04.03 Textile-reinforced hoses - Part 1: Maximal working pressure PN 10/16 (7)
DIN 20018-2
04.03 Textile-reinforced hoses - Part 2: Maximal working pressure PN 40 (5)
DIN 20018-3
04.03 Textile-reinforced hoses - Part 3: Maximal working pressure PN 100 (5)
DIN 20018-4
04.03 Textile-reinforced hoses - Part 4: Testing (6)
DIN 20021
02.97 Fluid-systems - Hoses with layer - Completation for DIN EN 853 to DIN EN 857
(5)
DIN 20029
10.90 Hose fittings; 1:3 taper gauges (5)
DIN 20030
06.92 Hose fittings; straight-way-cock with grip; dimensions, materials, requirements
(5)
DIN 20033
07.90 Hose fittings; tapered nozzle with clamping nut (6)
DIN 20036
10.90 Hose fittings; coupling nipples with round thread form (5)
DIN 20036
10.90 Hose fittings; flange nozzle; nominal pressure 16 (5)
DIN 20037
10.90 Hose fittings; connecting nipple; dimensions (5)
DIN 20038
10.90 Hose fittings; coupling nozzles (5)
DIN 20039
08.98 Hose fittings - Hose clamps (5)
DIN 20040
10.90 Hose fittings; nipple valves; nominal pressure 16 (5)
DIN 20043
09.03 Staple-lock couplings for hydraulic power-transmission circuits (7)
DIN 20044
05.03 Staple-lock couplings type S for hydraulic power-transmission circuits Dimensions, requirements, testing (7)
DIN 20066
01.12 Hydraulic fluid power - Hose assemblies - Dimensions, requirements (13)
/FABERG co-author/
NA 008-05-08 AA Mobile machines
DIN EN 1889-1
10.11 Machines for underground mines - Mobile machines working underground Safety - Part 1: Rubber tyred vehicles; German version EN 1889-1:2011 (18)
DIN EN 1889-2
07.09 Machines for underground mines - Mobile machines working underground Safety - Part 2: Rail locomotives; German version EN 1889-2:2003+A1:2009
(20)
DIN EN 12111
10.15 Tunnelling machines - Road headers and continuous miners - Safety
requirements; German version EN 12111:2014 (20) /FABERG co-author/
DIN EN 16191
09.14 Tunnelling machinery - Safety requirements; German version EN 16191:2014
E DIN EN ISO 19296
12.15 Mining and earthmoving machinery - Mobile machines working underground Machine safety (ISO/DIS 19296.2:2015); German and English version prEN ISO
19296:2015 (19)
Page 17 of 44
FB Ventilation 06
06 Ventilation
NA 008-06-01 AA Air doors
DIN EN 12110
10.14 Tunnelling machines - Air locks - Safety requirements; German version EN
DIN 21631
03.11 Air regulating systems for mining - Wing air doors for travelling tracks - Onewing type air doors without pressure reduction (11)
DIN 21632
03.11 Air regulating systems for mining - Wing air doors for haulage tracks - One-wing
type air doors without pressure reduction (11)
DIN 21633
03.11 Air regulating systems for mining - Wing air doors for haulage tracks - Doublewing type doors without pressure reduction (12)
DIN 21634
03.11 Air regulation systems for mining - Swinging roadway air doors for haulage
tracks (11)
DIN 21635
02.98 Air regulation systems in mining - Air locks - Building and operation (7)
E DIN 21635
10.15 Air regulation systems for mining - Air locks - Building and operation (10)
DIN 21636
04.03 Air regulation systems in mining - Belt-conveyors-way air locks - Dimensions,
identifications, requirements and testing (12)
E DIN 21636
10.15 Air regulation systems in mining - Belt-conveyors-way air locks - Dimensions,
identifications, requirements and testing (15)
DIN 21637
10.95 Air regulation systems in mining - Wing air doors for haulage tracks - Doublewing type doors with pressure reduction (8)
E DIN 21637
10.15 Air regulation systems for mining - Wing air doors for haulage tracks - Doublewing type doors with pressure reduction (12)
DIN 21638
05.99 Air regulation systems in mining - Wing air locks for travelling tracks - Doublewing type doors with pressure reduction (6)
E DIN 21638
10.15 Air regulation systems for mining - Wing air locks for travelling tracks - Doublewing type doors with pressure reduction (12)
DIN 21639/B1
11.04 Corrigenda to DIN 21639:1999-09 (0)
DIN 21639
09.99 Air regulation systems in mining - Travel-way air locks - Type doors with
pressure (5)
E DIN 21639
DIN 21640-1
10.15 Air regulation systems for mining - Travel-way air locks with pressure-relief air
doors (6)
10.93 Air regulating systems in mining; pneumatic cylinders for airdoors without
pressure reduction; dimensions, requirement, marking (5)
NA 008-06-02 AA Installations for auxiliary ventilation
DIN 21603
10.09 Auxiliary ventilation for mining - Sheet airducting with collars and loose flanges
(5)
DIN 21605
07.10 Auxiliary ventilation for mining - Flexible plastic ventilation ducts for exhaust and
forced ventilation - Spiral ventilation ducts (6)
DIN 21606
07.10 Auxiliary ventilation for mining - Flexible plastic ventilation ducts for forced
ventilation - Flat ventilation ducts (6)
DIN 21610
07.10 Auxiliary ventilation in mining - Flexible plastic air ducts - Requirements and test
methods (6)
DIN 21612
07.10 Auxiliary ventilation for mining - Cladding material for flexible airducts Requirements, testing (5)
DIN 21613
10.09 Auxiliary ventilation for mining - Steel sheet connectors with flange and shoulder
(5)
DIN 21614
10.09 Auxiliary ventilation for mining - Flanged sheet steel reducers (5)
DIN 21615
10.09 Auxiliary ventilation for mining - Sheet steel reducers with flange and shoulder
(5)
Page 18 of 44
FB Ventilation 06
DIN 21625
07.10 Fans with electric motor drive intended for use in potentially explosive
atmospheres in coal mines (6)
DIN 21626
02.11 Fans with hybrid (electric/pneumatic) motor drive intended for use in potentially
explosive atmospheres in coal mines (6)
Page 19 of 44
FB Mine Safety 07
07 Mine Safety
NA 008-07-01 AA Personal safety and protective equipment
DIN EN 795
10.12 Personal fall protection equipment - Anchor devices; German version EN
DIN EN 1497
10.07 Personal fall protection equipment - Rescue harnesses; German version EN
DIN EN 1498
01.07 Personal fall protection equipment - Rescue loops; German version EN
DIN 5290-1
04.83 Snap hook from light metal; with setting nut; dimensions, requirements and
testing (5) /FABERG co-author/
DIN 7472-2
01.91 Safety harness; steel fittings; connecting dimensions, safety requirements and
testing (6) /FABERG co-author/
DIN EN ISO 14122-1
01.02 Safety of machinery - Permanent means of access to machinery - Part 1:
Choise of fixed means of access between tow levels (ISO 14122-1:2001);
E DIN EN ISO 14122-1
Choise of fixed means of access between two levels (ISO/DIS 14122-1:2013);
German version prEN ISO 14122-1:2013 (11) /FABERG co-author/
DIN EN ISO 14122-2
Working platforms and wlkways (ISO 14122-2:2001); German version EN ISO
14122-2:2001 (7) /FABERG co-author/
Working platforms and walkways (ISO/DIS 14122-2:2013); German version
prEN ISO 14122-2:2013 (11) /FABERG co-author/
DIN EN ISO 14122-3
01.02 Safety of machinery - Permanent means of access to machinery - Part 3: Stairs,
stepladders and guard-rails (ISO 14122-3:2001); German version EN ISO
01.14 Safety of machinery - Permanent means of access to machinery - Part 3: Stairs,
stepladders and guard-rails (ISO/DIS 14122-3:2013); German version prEN ISO
14122-3:2013 (13) /FABERG co-author/
02.14 Safety of machinery - Permanent means of access to machinery - Part 4: Fixed
ladders (ISO/DIS 14122-4:2014); German version prEN ISO 14122-4:2014 (20)
/FABERG co-author/
DIN EN 14404
02.05 Personal protective equipment - Knee protectors for work in the neeling
position; German version EN 14404:2004 (12) /FABERG co-author/
DIN 20180
06.10 Pulley for clothes hoists in pithead baths (5)
DIN 20182
06.10 Double loop chain for hoisting clothes in pithead baths - Not tested, noncalibrated (4)
DIN EN ISO 20344
02.13 Personal protective equipment - Test methods for footwear (ISO 20344:2011);
DIN EN ISO 20345
04.12 Personal protective equipment - Safety footwear (ISO 20345:2011); German
DIN EN ISO 20346
09.14 Personal protective equipment - Protective footwear (ISO 20346:2014); German
DIN EN ISO 20347
05.12 Personal protective equipment - Occupational footwear (ISO 20347:2012);
DIN 21800
06.89 Symbol mallet and iron (5)
DIN 21802
06.89 Symbols for mine rescue and gas protection squads (6)
DIN 23301
03.07 Safety footwear for underground mining (9)
DIN 23307
06.09 Leather backside protectors for miners (back skin) (5)
DIN 23311-1
03.15 Knee pads for mining - Part 1: Rubber knee pads (5)
Page 20 of 44
FB Mine Safety 07
DIN 23311-2
11.15 Knee pads for mining - Part 2: Plastic knee pads (8)
DIN 23320-1
10.14 Flameproof protective clothing for the mining industry - Protective clothing for
people of mine rescue and gas rescue crews - Part 1: Safety requirements and
testing (10)
DIN 23320-2
people of mine rescue and gas rescue and gas rescue crews - Part 2: Singlepiece working suits (6)
DIN 23320-3
people of mine rescue and gas rescue crews - Part 3: Two-piece working suits
(6)
DIN 23320-4
people of mine rescue and gas rescue crews - Part 4: Underwear (6)
DIN 23320-5
10.14 Flameproof protective clothing for the mining industry - Protecting clothing for
people of mine rescue and gas rescue crews - Part 5: Protective hoods (8)
DIN 23323
05.07 Bathing sandals for miners (5)
DIN 23327
07.03 Shin protectors for mining (7)
DIN 23328
09.03 Clothing for the mining industry - Woven farbics for work suits (6)
DIN 23330
03.15 Safety markings for mines (7)
DIN 23341
05.05 Clothing for the mining industry - Two-piece work suits (Jacket and trousers) (7)
DIN 23342
08.05 Clothing for the mining industry - Singlet with 1/4 sleeves (7)
DIN 23343
03.07 Clothing for the mining industry - Shirt for miners (7)
DIN 23344
09.03 Clothing for the mining industry - Men's slip (6)
DIN 23345
08.05 Clothing for the mining industry - Long underpants (7)
DIN 23346
09.03 Clothing for the mining industry - Socks for mining workers (6)
DIN 23400
11.08 Rescue stretcher for mining (dragging basket) - Safety requirements and testing
(10)
DIN 23405
09.12 First aid boxes and first aid material for use in mining (5)
DIN 24320
12.06 Fire resistant fluids - Hydraulic fluids of categories HFAE and HFAS Characteristics and requirements (7) /FABERG co-author/
DIN 24531-1
04.06 Gratings used as stairtreads - Part 1: Metal gratings (7) /FABERG co-author/
DIN 24531-2
08.07 Gratings used as stairtreads - Part 2: Sheet metal gratings (7) /FABERG coauthor/
DIN 24531-3
08.07 Gratings used as stairtreads - Part 3: Plastic gratings (6) /FABERG co-author/
DIN 24534
03.70 Chain locks (4) /FABERG co-author/
DIN 24537-1
04.06 Gratings used as floor coverings - Part 1: Metal gratings (7) /FABERG co-author/
DIN 24537-2
08.07 Gratings used as floor coverings - Part 2: Sheet metal gratings (7) /FABERG coauthor/
DIN 24537-3
08.07 Gratings used as floor coverings - Part 3: Plastic gratings (7) /FABERG coauthor/
DIN 34300
04.01 Rescue equipment - Rescue hooks with safety eyelet holes (6) /FABERG coauthor/
DIN 51502
08.90 Designation of lubricants and marking of lubricant containers, equipment and
lubricating points (7) /FABERG co-author/
DIN 51634
12.81 Mineral spirits; safety lamps mineral spirit; minimum requirements (5)
/FABERG co-author/
NA 008-07-02 AA Lighting
DIN 20609
11.93 Lighting of mine locomotives; head lamps; design features, photometric
requirements, meters and measurements (6)
Page 21 of 44
FB Mine Safety 07
DIN 20610
04.94 Lighting of mine locomotives; position lamps; design features, photometric
requirements (5)
DIN 22433
10.03 Underground lighting in hardcoal mining - Terms (6)
DIN 22434-1
07.01 Underground lighting in hardcoal mining - Lighting-technological planning
bases - Part 1: General specification (6)
DIN 22434-2
bases - Part 2: Coalfaces with shield support (5)
DIN 22434-3
bases - Part 3: T-junctions (5)
DIN 22434-4
bases - Part 4: Conveyor belt (5)
DIN 22434-5
bases - Part 5: Material handling places (5)
DIN 22434-6
bases - Part 6: Area of roadway-driving operation (5)
DIN 22434-7
bases - Part 7: Pit-bottom (5)
DIN 22434-8
bases - Part 8: Building sites (5)
DIN 22434-9
bases - Part 9: Areas of rail track operation (5)
DIN 22434-10
bases - Part 10: Workshops and special premises (6)
DIN 49741
11.68 Lamp cap BX22d/32 (4) /FABERG co-author/
DIN EN 60079-35-1
01.12 Explosive atmospheres - Part 35-1: Caplights for use in mines susceptible to
firedamp - General requirements - Construction and testing in relation to the
risk of explosion (IEC 60079-35-1:2011); German version EN 60079-351:2011 + Cor.:2011 (19) /FABERG co-author/
DIN EN 60079-35-2
12.12 Explosive atmospheres - Part 35-2: Caplights for use in mines susceptible to
firedamp - Performance and other safety-related matters (IEC 60079-352:2011); German version EN 60079-35-2:2012 /FABERG co-author/
NA 008-07-03 AA Explosion prevention and protection
DIN EN 1127-2
09.14 Explosive atmospheres - Explosion prevention and protection - Part 2: Basic
concepts and methodology for mining; German version EN 1127-2:2014 (16)
DIN EN 1710
08.08 Equipment and components intended for use in potentially explosive
atmospheres in underground mines; German version EN 1710:2005+A1:2008
(17)
DIN EN 1834-2
03.00 Reciprocating internal combustion engines - Safety requirements for design and
construction of engines for use in potentially explosive atmospheres - Part 2:
Group I engines for use in underground workings susceptible to firedamp and/or
combustible dust; German version EN 1834-2:2000 (10) /FABERG co-author/
DIN EN 13463-1
07.09 Non-electrical equipment for use in potentially explosive atmospheres - Part 1:
Basic method and requirements; German versionrEN 13463-1:2009 (26)
/FABERG co-author/
DIN EN 13463-5
10.11 Non-electrical equipment intended for use in potentially explosive atmospheres Part 5: Protection by constructional safety "c"; German version EN 134635:2011 (17) /FABERG co-author/
DIN EN 14591-1
12.04 Explosion prevention and protection in underground mines - Protective
systems - Part 1: 2-bar explosion proof ventilation structures; German version
EN 14591-1:2004 (10)
DIN EN 14591-1/B1
systems - Part 1: 2-bar explosion proof ventilation structures, Corrigenda to DIN
EN 14591-1:2004-12; German version EN 14591-1:2004/AC.2006 (99)
Page 22 of 44
FB Mine Safety 07
DIN EN 14591-2
systems - Part 2: Passive water trough barriers; German Version EN 145912:2007 (17)
DIN EN 14591-4
09.07 Explosions prevention and protection in underground mines - Protective
systems - Part 4: Automatic extinguishing systems for road headers; German
version prEN 14591-4:2005 (9)
DIN EN 14983
06.07 Explosion prevention and protection in underground mining - Equipment and
protective systems for firedamp drainage; German version EN 14983:2007 (13)
DIN 21577
09.96 Explosibility of coal dust in underground hard coal mining - Tests and
assessments of coal dust-air-mixtures and hybrid mixtures (8)
DIN EN 50303
05.01 Group 1, category M1 equipment intended to remain functional in atmospheres
endangered by firedamp and/or coal dust; German version EN 50303:2000 (7)
/FABERG co-author/
E DIN EN ISO 8007936
09.14 Explosive atmospheres - Part 36: Non-electrical equipment for use in explosive
atmospheres - Basic methods and requirements (ISO/DIS 80079-36:2014);
German version prEN ISO 80079-36:2014 (29) /FABERG co-author/
E DIN EN ISO 8007937
09.14 Explosive atmospheres - Part 37: Non-electrical equipment for use in explosive
atmospheres - Non electrical type of protection constructional safety "c", control
of ignition source "b", liquid immersion "k" ISO/DIS 80079-37:2014); German
version prEN ISO 80079-37:2014 (21) /FABERG co-author/
E DIN EN ISO/IEC
80079-38
08.12 Explosive atmospheres - Part 38: Equipment and components in explosive
atmospheres in underground mines (ISO/IEC 80079-38/CDV:2012); German
version prEN ISO/IEC 80079-38:2012 (23)
NA 008-07-03-01 AK Apparatus for potentially explosive atmospheres for mining
DIN 20401
12.04 Buttress threads - 0,8 mm to 2 mm pitch - Dimensions (6)
DIN 22416
09.86 Electrical apparatus for potentially explosive atmospheres in mining; triangular
head bolts; safety requirements and testing (5)
DIN 22417
11.88 Electrical apparatus for potentially explosive atmospheres; forms of keys for
triangular socket wrenches (5)
DIN 22418
04.89 Electrical apparatus for potentially explosive atmospheres for mining; screw
plugs; safety requirements and testing (6)
DIN 22419-1
12.04 Electrical apparatus for potentially explosive atmospheres for mining - Cable
entries - Part 1: Requirements for basic design (8)
DIN 22419-2
entries - Part 2: Gland adaptors for entries; safety requirements and testing (6)
DIN 22419-3
entries - Part 3: Gland flanges for entries; safety requirements and testing (7)
DIN 22424
03.90 Electrical apparatus for potentially explosive atmospheres for mining; triangle
head bolts (6)
DIN 22425
03.90 Electrical apparatus for potentially explosive atmospheres for mining; triangular
nuts (6)
NA 008-07-04 AA Blasting engineering
DIN EN 13630-1
03.04 Explosives for civil uses - Detonating cords and safety fuses - Part 1:
Requirements; German version EN 13630-1:2003 (7)
DIN EN 13630-2
Determination of thermal stability of detonating cords and safety fuses; German
version EN 13630-2:2002 (7)
DIN EN 13630-3
Determination of sensitiveness to friction of the core of detonating cords;
German version EN 13630-3:2002 (6)
DIN EN 13630-4
Determination of sensitiveness to impact of detonating cords; German version
EN 13630-4:2002 (8)
Page 23 of 44
FB Mine Safety 07
DIN EN 13630-5
Determination of resistance to abrasion of detopnating cords; German version
EN 13630-5:2003 (9)
DIN EN 13630-6
Determination of resistance to tension of detonating cords; German version EN
13630-6:2002 (6)
DIN EN 13630-7
Determination of reability of initiation of detonating cords; German version EN
13630-7:2002 (6)
DIN EN 13630-8
Determination of resistance to water of detonating cords and safety fuses;
DIN EN 13630-9
Determination of transmission of detonation from detonating cord to detonating
cord; German version EN 13630-9:2004 (7)
DIN EN 13630-10
Determination of initiating capacity of detonating cords; German version EN
1360-10:2005 (8)
DIN EN 13630-11
Determination of velocity of detonation of detonating cords; German version EN
13630-11:2002 (6)
DIN EN 13630-12
Determination of burning duration of safety fuses, German version EN 1363012:2002 (6)
DIN EN 13631-1
07.05 Explosives for civil uses - High explosives - Part 1: Requirements; German
version EN 13631-1:2005 (7)
DIN EN 13631-2
12.02 Explosives for civil uses - High explosives - Part 2: Determionation of thermal
stability of explosives; German version EN 13631-2:2002 (7)
DIN EN 13631-3
11.04 Explosives for civil uses - High explosives - Part 3: Determionation of
sensitiveness to friction of explosives; German version EN 13631-3:2004 (8)
DIN EN 13631-4
sentiveness to impact of explosives; German version EN 13631-4:2002 (8)
DIN EN 13631-5
12.02 Explosives for civil uses - High explosives - Part 5: Determionation of resistance
to water; German version EN 13631-5:2002 (7)
DIN EN 13631-6
12.02 Explosives for civil uses - High explosives - Part 6: Determionation of resistance
to hydrostatic pressure; German version EN 13631-6:2002 (7)
DIN EN 13631-7
02.04 Explosives for civil uses - High explosives - Part 7: Determionation of safety and
reliability at extreme temperatures; German version EN 13631-7:2003 (7)
DIN EN 13631-10
02.04 Explosives for civil uses - High explosives - Part 10: Method for the verification
of the means of initiation; German version EN 13631-10:2003 (8)
DIN EN 13631-11
transmission of detonation; German version EN 13631-11:2003 (8)
DIN EN 13631-12
02.05 Explosives for civil uses - High explosives - Part 12: Specification of boosters
with different initiating capability; German version EN 13631-12:2004 (6)
DIN EN 13631-13
07.03 Explosives for civil uses - High explosives - Part 13: Determionation of density;
DIN EN 13631-14
07.03 Explosives for civil uses - High explosives - Part 14: Determionation of velocity
of detonation; German version EN 13631-14:2003 (8)
DIN EN 13631-15
07.05 Explosives for civil uses - High explosives - Part 15: Calculation of
thermodynamic properties; German version prEN 13631-15:2003 (12)
DIN EN 13631-16
11.04 Explosives for civil uses - High explosives - Part 16: Detection and
measurement of toxic gases; German version EN 13631-16:2004 (7)
DIN 20163
11.94 Blasting - Terminology, units and symbols (14)
DIN 20164-1
01.07 Blasting supplies - Explosives - Part 1: Requirements, testing, marking (12)
Page 24 of 44
FB Mine Safety 07
DIN 20165
08.10 Blasting supplies - Intrinsically safe detonators (permitted detonators) Requirements and testing (8)
DIN 20166
11.12 Blasting supplies - Intrinsically safe detonating cords (permitted detonating
cords) - Safety requirements and testing (10)
NA 008-07-05 AA Plastics
DIN 22100-1
07.09 Articles and materials from synthetics for use in underground mines - Part 1:
Conveyor belts - Hygienic requirements, testing, marking (8)
DIN 22100-3
10.10 Articles and materials from synthetic for use in underground mines - Part 3:
Spiral air ducts - Safety requirements, testing, marking (8)
DIN 22100-4
10.10 Articles and materials from synthetic for use in underground mines - Part 4: Flat
air ducts - Safety requirements, testing, marking (6)
DIN 22100-5
Tubes, tube isolations and hoses - Safety requirements, testing, marking (8)
DIN 22100-6
Sheeting, coated/uncoated tissue, brattice materials and lagging mats - Safety
requirements, testing, marking (7)
DIN 22100-7
08.11 Articles and materials from synthetics for use in underground mines - Part 7:
Safety requirements, testing, marking (24)
Page 25 of 44
FB Analysis of Raw Material/Coal preparation 08
08 Analysis of Raw Material/Coal preparation
NA 008-08-01 AA Investigations of raw material/Preparation of hard coal
DIN 22005-1
09.14 Investigations of raw material in hard-coal-mining - Part 1: Survey (10)
DIN 22005-2
06.15 Investigations of the raw material in hard-coal-mining - Part 2: Terms relating to
raw material (13)
DIN 22013
08.85 Investigations of the raw material in hard-coal-mining - Channel sample Sampling and schema of tests (9)
DIN 22014
08.85 Investigations of the raw material in hard-coal mining - Raw coal sample from
the production of a working area - Sampling and schema of tests (10)
DIN 22017
11.15 Investigations of the raw material in hard-coal-mining - Froth-flotation-analysis
(13)
DIN 22018
01.85 Investigations of the raw material in hard-coal-mining determation of the particledensity-distribution by float-and-sink-analysis (10)
DIN 22019-1
03.85 Investigations of the raw material in hard-coal-mining; determination of the
particle-size-distribution <größer>20 µm by sieve-analysis (12)
DIN 22020-1
08.98 Investigations of raw material in hard-coal-mining - Microscopical examination of
hard coal, coke and briquettes - Part 1: Terms, survey of processes and their
applications (7)
DIN 22020-2
hard coal, coke and briquettes - Part 2: Preparation of polished surface from
lump material and particulate blocks (5)
DIN 22020-3
hard coal, coke and briquettes - Part 3: Maceral analysis on particulated blocks
(5)
DIN 22020-4
hard coal, coke and briquettes - Part 4: Microlithotype analysis on particulate
blocks (6)
DIN 22020-5
02.05 Investigations of the raw material in hard-coal-mining - Microscopical
examinations of hard coal, coke and briquettes - Part 5: Reflectance
measurements on vitrinites (12)
BB 22020-7
09.74 Mikroskopische Untersuchungen an Steinkohlen, Koksen und Briketts Sonderuntersuchungen (4)
DIN 22021
07.85 Investigations of the raw material in hard-coalmining - Microscopical
examinations of rocks (17)
DIN 22024
02.89 Investigations of the raw material in hard-coal-mining - Determination of tensile
strength on solid rock (5)
DIN 23004-1
11.11 Preparation of hard coal - Part 1: Survey (7)
DIN 23004-2
11.11 Preparation of hard coal - Part 2: Terms relating to processes (14)
DIN 23005
12.88 Preparation of hard coal - Description and estimation of raw coal properties in
view of preparation (10)
DIN 23006-1
01.05 Preparation of hard coal - Assessment of preparation equipment and
processes - Part 1: General rules, balance of quantities (15)
DIN 23006-2
processes - Part 2: Sizing (14)
DIN 23006-3
processes - Part 3: Cleaning (13)
DIN 23006-4
processes - Part 4: Separation of solids from water (12)
DIN 23006-5
processes - Part 5: Size reduction and dissociation, involuntary breakage (10)
Page 26 of 44
FB Analysis of Raw Material/Coal preparation 08
DIN 23006-6
processes - Part 6: Homogenizing (11)
DIN 23007
10.05 Preparation of hard coal - Flocculants for process water - Terms, requirements,
verification (12)
DIN 23009
03.90 Preparation of hard coal - Medium solids - Terms, requirements, testing (9)
DIN 23011-3
12.13 Preparation of hard coal - Preparation-plants - Part 3: Flow sheets and grafical
symbols (15)
DIN 23011-4
11.06 Preparation of hard coal; preparation plants Part 4: Technical agreements with
regard to the fixation of guaranties (7)
DIN 23011-5
11.06 Preparation of hard coal - Preparation plants - Part 5: Process control (9)
DIN 23011-6
12.04 Preparation of hard coal - Preparation plants - Part 6: Equipment and operation
of a plant laboratory (9)
DIN 23011-7
11.06 Preparation of hard coal - Preparation plants - Part 7: Equipment monitoring (7)
DIN 23011-7 Bbl 1
12.09 Preparation of hard coal - Preparation plants - Part 7: Equipment monitoring;
Supplement 1: Means of application for the standard (7)
DIN 23011-8
02.08 Preparation of hard coal - Preparation plants - Part 8: Process technical
requirements on preparation equipment (13)
Page 27 of 44
FB Cokery, Briquettes 09
09 Cokery, Briquettes
NA 008-09-01 AA Bricks for coke ovens
DIN 1089-1
02.95 Refractories for use in coke ovens - Part 1: Silica bricks - Requirements and
testing (6)
DIN 1089-2
02.95 Refractories for use in coke ovens - Part 2: Fireclay bricks - Requirements and
testing (7)
DIN 1089-3
10.90 Refractories for use in coke ovens; mortar for silica and fireclay bricks;
requirements and testing (7)
Page 28 of 44
FB Open Cast Mining 10
10 Open Cast Mining
NA 008-10-01 AA Excavators, spreaders and auxiliary equipment in opencast lignite mines
DIN 5651
11.79 Brake block holders and brake block keys for composite brake blocks on rail
vehicles; technical specifications (4) /FABERG co-author/
DIN 22261-1
11.15 Excavators, spreaders and auxiliary equipment in opencast lignite mines - Part
1: Construction, commissioning and monitoring (11)
DIN 22261-2
2: Calculation principles (32)
DIN 22261-3
3: Execution of steel structures (19)
DIN 22261-4
4: Hoisting winch brakes (5)
DIN 22261-5
5: Slewing brakes and overload protecting devices (6)
DIN 22261-6
6: Examination of ropes and rope end fittings (7)
DIN 43120
09.52 Electric railway vehicles; bow slipper holder for contact wire clamps (4)
/FABERG co-author/
DIN 43139
12.67 Drums for contact-wires for electric traction (4) /FABERG co-author/
DIN 43153
01.68 Thimble with clevis for overhead equipment (4) /FABERG co-author/
DIN 43160
01.68 Eye and clevis for overhead equipment; connecting dimensions (4) /FABERG
co-author/
NA 008-10-02 AA Belt conveyors in opencast lignite mining
DIN EN 14658
06.10 Continuous handling equipment and systems - General safety requirements for
continuous handling equipment for opencast lignite mining; German version EN
14658:2005+A1:2010 (15)
NA 008-10-03 AA Surface Miner
DIN 22270
05.12 Continuous Surface Miner (CSM) - Safety (11)
Page 29 of 44
FB Mine Plans 11
11 Mine Plans
NA 008-11-01 AA Mine surveying
DIN 21961
06.00 Mine surveying - Slip-on pivots, slip-on caps for suspension theodolites Connecting dimensions (5)
NA 008-11-01-01 AK Basics
DIN 21901
02.84 Mine plans; structure and list of standards; general principles (5)
DIN 21901 Bbl 1
01.12 Mine plans - Structure and list of standards -Supplement 1: Contents (6)
DIN 21901 Bbl 2
09.06 Mine plans - Structure and list of standards - Supplement 2: List of
abbreviations (18)
DIN 21901 Bbl 3
07.02 Mine plans; structure and list of standards; index (23)
DIN 21901-2
11.94 Mine plans - Structure and list of standards - Part 2: Interface for EDP based
transfer of symbols of mining - Specific mapping (12)
DIN 21902
10.99 Mine plants - Structure of mining specific plans (7)
DIN 21902-2
08.08 Mine plants - Structure of mining specific plans - Part 2: Completion of mine
plans (11)
DIN 21903
10.95 Mine plans - Sizes and foldings (8)
DIN 21904
01.94 Mine plants; lettering (5)
DIN 21905
11.93 Mine plants; drawing principles (5)
DIN 21906
08.90 Mine plans - Subdivision of sheets (9)
E DIN 21906
12.15 Mine plans - Subdivision of sheets (12)
DIN 21906 Bbl 1
11.91 Mine plans; subdivision of sheets; survey (19)
DIN 21906 Bbl 2
01.94 Mine plans; subdivision of sheets; survey (14)
DIN 21907
04.03 Mine plans - Graphic design of sheets (12)
DIN 21908
01.94 Mine plans - Colours (8)
NA 008-11-01-02 AK Objects on the surface, open pit mines
DIN 21909
02.02 Mine plans - Survey points and lines (9)
DIN 21910
11.14 Mine plans - Titles and boundaries (13)
DIN 21911
03.08 Mine plans; objects on the surface and contour lines (12)
DIN 21912-1
01.06 Mine plans - Opencast mining - Part 1: General requirements (12)
DIN 21912-2
01.11 Mine plans - Open cast mining - Part 2: Reconstruction (12)
DIN 21912-3
01.13 Mine plans - Open cast mining - Part 3: Operating plan (7)
NA 008-11-01-03 AK Geologic symbols and terms
DIN 21918-1
10.99 Mine plans - Mineral deposits - Part 1: Terms, classification (6)
DIN 21918-2
08.04 Mine plans - Mineral deposits - Part 2: Thicknesses (10)
DIN 21919-1
03.13 Mine plans - Stratigraphy - Part 1: General classification (10)
DIN 21919-2
12.08 Mine plans - Stratigraphy - Part 2: Regional and local subdivisions; Hard coal (8)
DIN 21919-3
11.01 Mine plans - Stratigraphy - Part 3: Regional and local subdivisions; Lignite (9)
DIN 21920-1
03.13 Mine plans - Petrography - Part 1: Generally applicable symbols - Sediments
(10)
DIN 21920-2
04.96 Mine plans - Petrography - Part 2: Magmatites (10)
DIN 21920-3
04.96 Mine plans - Petrography - Part 3: Metamorphic and other lithogenetic
phenomena (10)
DIN 21920-4
04.96 Mine plans - Petrography - Part 4: Minerals (6)
Page 30 of 44
FB Mine Plans 11
DIN 21920-5
11.94 Mine plans - Petrography - Part 5: Hard coal mining (12)
DIN 21920-7
04.96 Mine plans - Petrography - Part 7: Potash and rock salt mining (7)
DIN 21921
04.96 Mine plans - Tectonic elements and figure of strata (13)
DIN 22011
11.93 Investigations of the raw material in hard-coal-mining - Treatment of exploratory
drillings (17)
DIN 22012
01.94 Investigations of the raw material in hard-coal-mining - Macropetrographic
classification and topographic survey of hard-coal and host rock (8)
DIN 22015
10.93 Investigations of the raw material in hardcoal-mining - Macroscopic
classification and description of overburden rock (9)
NA 008-11-01-04 AK Special representations
DIN 21913-11
01.00 Mine plans - Deep mining - Part 11: Geometrical dimensions in underground
workings (7)
DIN 21915
12.13 Mine plans - Technical facilities (11)
DIN 21916-1
02.07 Mine plans - Operational safety - Part 1: Ventilation system and meteorology (13
DIN 21916-2
02.10 Mine plans - Operational safety - Part 2: Fire prevention on the surface (12)
DIN 21916-3
01.11 Mine plans - Operational safety - Part 3: Fire prevention under the surface (11)
DIN 21917
02.99 Mine plans - Strata and ground movements (13)
DIN 21917-2
12.15 Mine plans - Strata and ground movements - Part 2: Geotechnical measuring
points (12)
NA 008-11-01-05 AK Mine workings
DIN 21913-1
02.92 Mine plans; deep mining; underground workings (19)
DIN 21913-1 Bbl 1
02.92 Mine plans; underground working; storage and final deposition in mine workings
(33)
DIN 21913-2
02.09 Mine plans - Deep mining - Part 2: Extraction, stowage and deposit (14)
DIN 21913-3
02.08 Mine plans - Deep mining - Part 3: Closure of underground workings (8)
DIN 21913-4
02.09 Mine plans; deep mining; Part 4: hazardous zones, zones of protective
measures (11)
DIN 21913-6
11.14 Mine plans - Deep mining - Part 6: Safekeeping (10)
DIN 21913-7
01.12 Mine plans - Deep mining - Part 7: Shaft plan (10)
NA 008-11-01-06 AK Drilling, caverns, storage, final deposition
DIN 21914-1
10.05 Mine plans - Drilling and cavern - Part 1: Drilling (15)
DIN 21914-2
02.99 Mine plans - Drilling and cavern - Part 2: Brine caverns (10)
Page 31 of 44
FB Fuels 12
12 Fuels
NA 008-12-01 AA Gaseous fuels
DIN 1340
12.90 Gaseous fuels and other gases - Types, constituents, application (7) /FABERG
co-author/
DIN 1340 Bbl 1
12.90 Gaseous fuels and other gases - Types, constituents, application - Remarks on
the production (5) /FABERG co-author/
DIN 1871
05.99 Road marking materials - Physical properties; German version EN 1871:2000
DIN EN 1918-1
07.98 Gas supply systems - Underground gas storage - Part 1: Functional
recommendations for storage in aquifers; German version EN 1918-1:1998 (9)
/FABERG co-author/
E DIN EN 1918-1
DIN EN 1918-2
E DIN EN 1918-2
DIN EN 1918-3
E DIN EN 1918-3
DIN EN 1918-4
E DIN EN 1918-4
DIN EN 1918-5
E DIN EN 1918-5
06.14 Gas infrastructure - Underground gas storage - Part 1: Functional requirements
for storage in aquifers; German version prEN 1918-1:2014 (16) /FABERG coauthor/
07.98 Gas supply systems - Unterground gas storage - Part 2: Functional
recommendations for storage in oil and gas fields; German version EN 19182:1998 (8) /FABERG co-author/
06.14 Gas infrastructure - Unterground gas storage - Part 2: Functional requirements
for storage in oil and gas fields; German version prEN 1918-2:2014 (15)
/FABERG co-author/
recommendations for storage in solution-mined salt cavities; German version
EN 1918-3:1998 (10) /FABERG co-author/
06.14 Gas infrastructure -- Underground gas storage - Part 3: Functional
requirements for storage in solution-mined salt caverns; German version prEN
recommendations for storage in rock caverns; German version EN 19184:1998 (7) /FABERG co-author/
for storage in rock caverns; German version prEN 1918-4:2014 (15) /FABERG
co-author/
recommendations for surface facilities; German version EN 1918-5:1998 (6)
/FABERG co-author/
for surface facilities; German version prEN 1918-5:2014 (12) /FABERG coauthor/
DIN ISO 5275
10.05 Petroleum products and hydrocarbon solvents - Detection of thiols and other
sulfur species - Doctor test (ISO 5275:2003) (6) /FABERG co-author/
DIN EN ISO 6141
07.15 Gas analysis - Contents of certificates for calibration gas mixtures (ISO
DIN EN ISO 6143
11.06 Gas analysis - Comparison methods for determining and checking the
composition of calibration gas mixtures (ISO 6143:2001); German version EN
DIN EN ISO 6326-3
04.98 Natural gas - Determination of sulfur compounds - Part 3: Determination of
hydrogen sulfide, mercaptan sulfur and carbonyl sulfide sulfur by potentiometry
(ISO 6326-3:1989); German version EN ISO 6326-3:1997 (7) /FABERG coauthor/
DIN EN ISO 6326-5
04.98 Natural gas - Determination of sulfur compounds - Part 5: Lingener combustion
method (ISO 6326-5:1989); German version EN ISO 6326-5:1997 (9)
/FABERG co-author/
Page 32 of 44
FB Fuels 12
DIN EN ISO 6570
12.04 Natural gas - Determination of potential hydrocarbon liquid content - Gravimetric
methods (ISO 6570:2001); English version EN ISO 6570:2004 (13) /FABERG
co-author/
DIN EN ISO 6974-1
11.12 Natural gas - Determination of composition and associated uncertainty by gas
chromatography - Part 1: General guidelines and calculation of composition
(ISO 6974-1:2012); German version EN ISO 6974-1:2012 (19) /FABERG coauthor/
DIN EN ISO 6974-2
chromatography - Part 2:Uncertainty calculations (ISO 6974-2:2012); German
DIN EN ISO 6974-3
06.02 Natural gas - Determination of composition with defined uncertainty by gas
chromatography - Part 3: Determination of hydrogen, helium, oxygen, nitrogen,
carbon dioxide and hydrocarbons up to C8 using two packed columns (ISO
6974-3:2000); German version EN ISO 6974-3:2001 / Note: Applies only in
conjunction with DIN EN ISO 6974-1 and DIN EN ISO 6974-2 (11) /FABERG
co-author/
DIN EN ISO 6974-4
chromatography - Part 4: Determination of nitrogen, carbon dioxide and C1- to
C5- and C6+ hydrocarbons for a laboratory and on-line measuring system
using two columns (ISO 6974-4:2000); German version EN ISO 6974-4:2001 /
Note: Applies only in conjunction with DIN EN ISO 6974-1 and DIN EN ISO
6974-2 (10) /FABERG co-author/
DIN EN ISO 6974-5
chromatography - Part 5: Isothermal method for nitrogen, carbon dioxide and
C1- to C5 hydrocarbons and C6+ hydrocarbons (ISO 6974-5:2014); German
DIN EN ISO 6974-6
chromatography - Part 6: Determination of hydrogen, helium, oxygen, nitrogen,
carbon dioxide and C1 to C8 hydrocarbons using three capillary columns (ISO
6974-6:2002); German version EN ISO 6974-6:2005 (12) /FABERG co-author/
DIN EN ISO 6975/B1
09.08 Natural gas - Extended analysis - Gas-chromatographic method (ISO
6975:1997); German version EN ISO 6975:2005, Corrigendum to DIN EN ISO
6975:2005-09 (99) /FABERG co-author/
DIN EN ISO 6975
09.05 Natural gas - Extended analysis - Gas-chromatographic method (ISO
DIN EN ISO 6976
09.05 Natural gas - Calculation of calorific values, density, relative density and Wobbe
index form composiotion (ISO 6976:1995 + Corrigendum 1:1997, Corrigendum
2:1997, Corrigendum 3:1999); German version EN ISO 6976:2005 (22)
/FABERG co-author/
DIN EN ISO 6978-1
09.05 Natural gas - Determination of mercury - Part 1: Sampling of mercury by
chemisorption on iodine (ISO 6978-1:2003); German version EN ISO 69781:2005 (12) /FABERG co-author/
DIN EN ISO 6978-2
09.05 Natural gas - Determination of mercury - Part 2: Sampling of mercury by
amalgamation on gold/platinum alloy (ISO 6978-2:2003); German version EN
ISO 6978-2:2005 (12) /FABERG co-author/
DIN EN ISO 10101-1
07.98 Natural gas - Determination of water by the Karl Fischer method - Part 1:
Introduction (ISO 10101-1:1993); German version EN ISO 10101-1:1998 (6)
/FABERG co-author/
DIN EN ISO 10101-2
Tritation procedure (ISO 10101-2:1993); German version EN ISO 10101-2:1998
DIN EN ISO 10101-3
Coulometric procedure (ISO 10101-3:1993); German version EN ISO 101013:1998 (8) /FABERG co-author/
DIN EN ISO 10723
04.13 Natural gas - Performance evaluation for analytical systems (ISO 10723:2012);
Page 33 of 44
FB Fuels 12
DIN EN ISO 11541
02.03 Natural gas - Determination of water content at high pressure (ISO
11541:1997); German version prEN ISO 11541:2002 (7) /FABERG co-author/
DIN EN ISO 12213-1
01.10 Natural gas - Calculation of compression factor - Part 1: Introduction and
guidelines (ISO 12213-1:2006); German version EN ISO 12213-1:2009 (11)
/FABERG co-author/
DIN EN ISO 12213-2
01.10 Natural gas - Calculation of compression factor - Part 2: Calculation using molarcomposition analysis (ISO 12213-2:2006); German version EN ISO 122132:2009 (16) /FABERG co-author/
DIN EN ISO 12213-3
01.10 Natural gas - Calculation of compression factor - Part 3: Calculation using
physical properties (ISO 12213-3:2006); German version EN ISO 12213-3:2009
DIN 12473-1
04.76 Laboratory glassware - gas sampling tubes with straight bore stopcocks (4)
/FABERG co-author/
DIN 12473-2
04.76 Laboratory glassware - gas sampling tubes with V-bore stopcocks (4) /FABERG
co-author/
DIN EN ISO 14111
06.00 Naturalgas - Guidelines to traceability in analyses (ISO 14111:1997); German
DIN EN ISO 18453
01.06 Natural gas - Correlation between water content and water dew point (ISO
18453:2004); German version prEN 18453:2005 (13) /FABERG co-author/
BB 22061-1
04.82 Steinkohlenbergbau - Gase unter Tage - Anwendungsbereich, Zweck, Begriffe
und Allgemeines (1)
BB 22061-2
04.82 Steinkohlenbergbau - Gase unter Tage - Probenahme (4)
BB 22061-3
04.82 Steinkohlenbergbau - Gase unter Tage - Analyse nach physikalischen
Verfahren im Laboratorium (2)
DIN 51400-4
04.00 Testing of mineral oils and fuels - Determination of sulfur content (total sulfur) Part 4: Combustion according to the Lingener method, visual titration,
turbidmetric-titration (6) /FABERG co-author/
DIN 51851
04.80 Testing of gaseous fuels and other gases; calculation of reduced gas volume
DIN 51853
12.11 Testing of fuel gases - Sampling (11) /FABERG co-author/
DIN 51854
09.93 Testing of gaseous fuels and other gases; determination of ammonia content
DIN 51855-1
09.11 Testing of gaseous fuels and other gases - Determination of the content of
sulphur compounds - Part 1: Field of application, terms (5) /FABERG co-author/
DIN 51855-4
06.95 Testing of gaseous fuels and other gases - Determination of sulphur
compounds content - Part 4: Content of hydrogen sulfide, zinc acetate method
DIN 51855-6
09.00 Testing of gaseous fuels and other technical gases - Determination of sulfur
compounds content - Part 6: Content of hydrogen sulfide, mercaptan sulfur and
carbonylsulfide sulfur; potentiometric method (6) /FABERG co-author/
DIN 51855-7
12.86 Testing of gaseous fuels and other gases; determination of the content of sulfur
compounds; gaschromatographic determination of the content of odoriferous
sulfur compounds using an electrochemical detector (5) /FABERG co-author/
DIN 51855-8
06.97 Testing of gaseous fuels and other gases - Determination of sulfur compounds
content - Part 8: Gaschromatographic determination of dihydrogen sulfide,
carbonyl sulfide and other sulfur compounds using specific detectors (7)
/FABERG co-author/
DIN 51857
03.97 Gaseous fuels and other gases - Calculation of calorific value, density, relative
density and Wobbe index of pure gases and gas mixtures (9) /FABERG coauthor/
DIN 51862
09.82 Testing of gaseous fuels and other gases; determination of naphthalene
content (crude naphthalene) (5) /FABERG co-author/
DIN 51863-1
09.83 Testing of gaseous fuels and other gases; determination of hydrogen cyanide
content; nickel carbonate method (6) /FABERG co-author/
Page 34 of 44
FB Fuels 12
DIN 51863-2
09.83 Testing of gaseous fuels and other gases; determination of hydrogen cyanide
content; bromide cyanogen method (5) /FABERG co-author/
DIN 51864
09.86 Testing of gaseous fuels and other gases; determination of nitrogen monoxide
content; Saltzman method (5) /FABERG co-author/
DIN 51865-1
09.98 Testing of gaseous fuels and other gases - Determination of mercury content Part 1: Chemisorption on Iodine, atomic absorption spectrometry (AAS) (6)
/FABERG co-author/
DIN 51865-2
10.00 Testing of gaseous fuels and other gases - Determination of mercury content Part 2: Combustion using the modified Lingener method; Atomic absorption
spectrometry (AAS) (6) /FABERG co-author/
DIN 51865-3
02.98 Testing of gaseous fuels and other gases - Determination of mercury content Part 3: Absorption in solutions, atomic absorption spectrometry (AAS) (6)
/FABERG co-author/
DIN 51869
09.00 Testing of gaseous fuels and other gases; determination of the main
components, general statements (5) /FABERG co-author/
DIN 51870
04.81 Testing of gaseaus fuels and other gases; determination of relative density
according to the balance method and calculation of density (6) /FABERG coauthor/
DIN 51871
12.85 Testing of gaseous fuels and other technical gases; determination of dew point
of water vapour; method of means of cooled mirror (5) /FABERG co-author/
DIN 51872-4
06.90 Testing of gaseous fuels and other gases; determination of the components;
gaschromatographic procedure (6) /FABERG co-author/
DIN 51872-5
08.96 Testing of gaseous fuels and other gases - Determination of the components Part 5: Capillary gaschromatographic procedure (8) /FABERG co-author/
NA 008-12-02 AA Testing of solid fuels
DIN 22022-1
07.14 Solid fuels - Determination of contents of trace elements - Part 1: General rules,
sampling and sample preparation - Preparation of samples for the analyses
(dissolution method) (7)
DIN 22022-2
02.01 Solid fuels - Determination of contents of trace elements - Part 2: ICP-OES (5)
DIN 22022-3
02.01 Solid fuels - Determination of trace elements - Part 3: AAS-flame method (5)
DIN 22022-4
02.01 Solid fuels - Determination of contents of trace elements - Part 4: Atomic
absorption spectrometry applying the flameless hydride system or the coldvapour-method (5)
DIN 22022-5
02.01 Solid fuels - Determination of trace elements - Part 5: Atomic absorption
spectrometry applying the electrothermal atomization (5)
DIN 22022-6
12.01 Solid fuels - Determination of trace elements - Part 6: Evaluation and
declaration of results (7)
DIN 22022-7
07.14 Solid fuels - Determination of contents of trace elements - Part 7: ICP-MS (8)
DIN 51700
12.15 Testing of solid fuels - Generalities and index of methods of test (13)
DIN 51701-1
12.07 Testing of solid fuels - Sampling and sample preparation - Part 1: Definitions (6)
DIN 51701-2
09.06 Testing of solid fuels - Sampling and sample preparation - Part 2: Sampling (12)
DIN 51701-3
09.06 Testing of solid fuels - Sampling and sample preparation - Part 3: Sample
preparation (9)
DIN 51701-4
09.06 Testing of solid fuels - Sampling and sample preparation - Part 4: Equipment
(10)
DIN 51701-5
03.08 Testing of solid fuels - Sampling and sample preparation - Part 5: Testing of
precision (12)
DIN 51705
06.01 Testing of solid fuels - Determination of the bulk density of solid fuels (5)
DIN 51717
07.94 Testing of solid fuels; determination of mechanical strength of coke (6)
E DIN 51717
07.15 Testing of solid fuels; determination of mechanical strength of coke (7)
Page 35 of 44
FB Fuels 12
DIN 51718
06.02 Testing of solid fuels - Determination of the water content and the moisture of
analysis sample (6)
DIN 51719
07.97 Testing of solid fuels - Solid mineral fuels - Determination of ash content (5)
DIN 51720
03.01 Testing of solid fuels - Determination of volatile matter content (7)
DIN 51721
08.01 Testing of solid fuels - Determination of carbon content and hydrogen content Radmacher-Hoverath method (6)
DIN 51722-1
07.90 Testing of solid fuels; determination of nitrogen content; semi-micro Kjeldahl
method (5)
DIN 51723
06.02 Testing of solid fuels - Determination of fluorine content (7)
DIN 51724-1
07.12 Testing of solid fuels - Determination of sulfur content - Part 1: Total sulfur (9)
DIN 51724-2
06.99 Testing of solid fuels - Determination of sulfur content - Part 2: Species (7)
DIN 51724-3
07.12 Solid minerals fuels - Determination of sulfur content - Part 3: Instrumental
methods (6)
DIN 51725
06.04 Testing of solid fuels - Determination of the phosphorus content (7)
DIN 51726
06.04 Testing of solid fuels - Determination of the carbonate carbon dioxide content (7)
DIN 51727
11.11 Testing of solid fuels - Determination of chlorine content (6)
DIN 51729-8
05.01 Solid fuels - Determination of chemical composition of fuel ash - Part 8:
Determination of soda and potash (Na<(Index)2>O, K<(Index)2>O) contents (5)
DIN 51729-10
04.11 Testing of solid fuels - Determination of chemical composition of fuel ash - Part
10: X-Ray Fluorescence Analysis (8)
DIN 51729-11
11.98 Testing of solid fuels - Determination of chemical composition of fuel ash - Part
11: Determination by inductively coupled plasma emission spectrometry (ICPOES) (5)
DIN 51730
09.07 Testing of solid fuels - Determination of fusibility of fuel ash (10)
DIN 51731
10.96 Testing of solid fuels - Compressed untreated wood - Requirements and testing
DIN 51732
07.14 Testing of solid mineral fuels - Determination of total carbon, hydrogen and
nitrogen - Instumental methods (7)
DIN 51733
12.08 Testing of solid mineral fuels - Ultimate analysis and calculation of oxygen
content (6)
E DIN 51733
07.15 Testing of solid mineral fuels - Ultimate analysis and calculation of oxygen
content (6)
DIN 51734
12.08 Testing of solid mineral fuels - Proximate analysis and calculation of fixed
carbon (6)
DIN 51735
02.09 Testing of solid mineral fuels - Determination of plastic properties of coal using
the Gieseler plastometer (9)
DIN 51739
05.98 Testing of solid fuels - Determination of the dilatation of coal (8)
DIN 51741
10.98 Testing of solid fuels - Determination of the crucible swelling number of coal (6)
DIN 51742
07.01 Testing of solid fuels - Determination of Hardgrove grindability index of hard coal
(7)
DIN 51900-1
04.00 Testing of solid and liquid fuels - Determination of gross calorific value by the
bomb calorimeter and calculation of net calorific value - Part 1: Principles,
apparatus, methods (12)
DIN 51900-1/B1
02.04 Corrigenda to DIN 51900-1:2000-04 (0)
DIN 51900-2
05.03 Testing of solid and liquid fuels - Determination of the gross calorific value by
the bomb calorimeter and calculation of the net calorific value - Method using
isoperibol or static jacket calorimeter (8)
DIN 51900-3
01.05 Testing of solid and liquid fuels - Determination of the gross calorific value by
the bomb calorimeter and calculation of net calorific value - Part 3: Method
Using Adiabatic Jacket (8)
Page 36 of 44
FB Cables, Telecontrol and Other Electrical Equipment 14
14 Cables, Telecontrol and Other Electrical Equipment
14 Cables, telecontrol and other electrical equipment
BB 22000-1
11.75 Größen und Einheiten - Teil 1: Einheiten - Allgemeine Grundlagen (3)
BB 22000-2
02.76 Größen und Einheiten - Teil 2: Masse, Kraft, Gewicht (1)
BB 22000-3
02.76 Größen und Einheiten - Teil 3: Temperatur, Druck (2)
BB 22442-1
03.03 Elektromagnetische Verträglichkeit für Anlagen im Steinkohlenbergbau - Teil 1:
Grundlagen (4)
BB 22442-2
03.03 Elektromagnetische Verträglichkeit für Anlagen im Steinkohlenbergbau - Teil 2:
Störaussendungs- und Störfestigkeits-Grenzwerte (4)
BB 22443
08.88 Geräte und Anlagen der Fernwirktechnik - Dokumentation von
Softwaresystemen (4)
BB 22444-1
02.76 Geräte und Anlagen der Fernwirktechnik - Begriffe (2)
BB 22444-2
10.82 Geräte und Anlagen der Fernwirktechnik - Anforderung und Prüfung (3)
BB 22444-3
07.87 Geräte und Anlagen der Fernwirktechnik - Schnittstellen (3)
BB 22444-4
07.87 Geräte und Anlagen der Fernwirktechnik - Standardaufbau einer
Telegrammschnittstelle zwischen Fernwirkstation und Prozeßrechner (3)
BB 22444-4 Bbl 1
07.87 Geräte und Anlagen der Fernwirktechnik - Standard für die serielle
Datenübertragung im Nahbereich (2)
BB 22444-4 Bbl 2
07.87 Geräte und Anlagen der Fernwirktechnik - Ablauf der Datenübertragung (1)
BB 22444-4 Bbl 3
07.87 Geräte und Anlagen der Fernwirktechnik - Ablaufbeispiel der Datenübertragung
(1)
BB 22445
10.73 Wassergekühlte polumschaltbare Drehstrommotoren, Bauform B5 Anbaumaße und Zuordnung der Leistungen bei Ausführung in Zündschutzart
(Sch) d (1)
BB 22446
05.87 Geräte und Anlagen der Fernwirktechnik - Frequenzbereiche für Funkanlagen
(2)
BB 22450-1
06.88 Grubenkabel für Fernmelde- und Informationsanlagen - Auswahl für den
Steinkohlenbergbau unter Tage (2)
BB 22450-2/A1
12.00 Leitungen für Fernmelde- und Informationsverarbeitungsanlagen - Auswahl für
den Steinkohlenbergbau unter Tage - Änderung 1 (2)
BB 22450-2
06.88 Leitungen für Fernmelde- und Informationsanlagen - Auswahl für den
Steinkohlenbergbau unter Tage (2)
BB 22450-3
06.99 Leitungen mit Litzenleitern für erhöhte mechanische Beanspruchung für
eigensichere elektrische Anlagen - Teil 3: Bewehrte Leitung L-2YYQY (blau) (4)
BB 22450-4
eigensichere elektrische Anlagen - Teil 4: Zugfeste, geschirmte Leitung L2Y(C)Y(ZG)Y (blau) (4)
BB 22450-5
eigensichere elektrische Anlagen - Teil 5: Zugfeste, geschirmte Leitungen L2YYC(ZG)Y (blau) (4)
BB 22450-6
06.99 Grubenkabel für erhöhte mechanische Beanspruchung für eigensichere
elektrische Anlagen - Teil 6: Bewehrtes Grubenkabel G-2YYYBY (blau) mit
Paaren (4)
BB 22450-7
06.99 Grubenkabel für erhöhte mechanische Beanspruchung für eigensichere
elektrische Anlagen - Teil 7: Bewehrtes Grubenkabel G-2YY(Z)Y (blau) mit
Paaren (4)
BB 22450-8
eigensichere elektrische Anlagen - Teil 8: Zugfeste Leitung L-YY(ZG)Y (blau) (4)
DIN 43620-5
06.86 Low-voltage high-rupturing capacity fuses with blade contacts; LV HRC fuse
links for AV 1000 V (5) /FABERG co-author/
Page 37 of 44
FB Solid mineral fuels ISO/TC 27
ISO/TC 27 Solid mineral fuels
ISO/TC 27 Solid mineral fuels
ISO 1213-2
04.92 Solid mineral fuels - Vocabulary - Part 2: Terms relating to sampling, testing and
analysis
ISO/TC 27/WG 18 Classification of coals
ISO 11760
02.05 Classification of coals
ISO/TC 27/SC 1 Coal preparation - Terminology and performance
ISO 561
12.89 Coal preparation plant - Graphical symbols
ISO 923
05.00 Coal cleaning equipment - Performance evaluation
ISO/DIS 923
10.15 Coal cleaning equipment - Performance evaluation
ISO 924
12.89 Coal preparation plant - Principles and conventions for flowsheets
ISO 1213-1
12.93 Solid mineral fuels - Vocabulary - Part 1: Terms relating to coal preparation
ISO 1953
11.15 Hard coal - Size analysis by sieving
ISO 7936
04.92 Hard coal - Determination and presentation of float and sink characteristics General directions for apparatus and procedures
ISO 8833
11.89 Magnetite for use in coal preparation - Test methods
ISO 8858-1
09.90 Hard coal - Froth flotation testing - Part 1: Laboratory procedure
ISO 8858-2
08.04 Hard coal - Froth flotation testing - Part 2: Sequential evaluation
ISO 8858-3
08.04 Hard coal - Froth flotation testing - Part 3: Release evaluation
ISO 10086-1
06.00 Coal - Methods for evalution flocculants for use in coal preparation - Part 1:
Basic parameters
ISO 10086-2
01.04 Coal - Methods for evaluating flocculants for use in coal preparation - Part 2:
Flocculants as filter aids in rotary vacuum filtration systems
ISO 10752
05.94 Coal sizing equipment - Performance evaluation
ISO 10753
02.94 Coal preparation plant - Assessment of the liability to breakdown in water of
materials associated with coal seams
ISO 15117-1
05.04 Coal flow properties - Part 1: Bin flow
ISO 20905
07.04 Coal preparation - Determination of dust/moisture relationship for coal
ISO 23499
07.13 Coal - Determination of bulk density for the use in charging of coke ovens
ISO/TC 27/SC 3 Coke
ISO 556
11.80 Coke (greater than 20 mm in size) - Determination of mechanical strength
ISO 567
07.95 Coke - Determination of bulk density in a small container
ISO 616
11.95 Coke - Determination of shatter indices
ISO 728
11.95 Coke (nominal top size greater than 20 mm) - Size analysis by sieving
ISO 1013
07.95 Coke - Determination of bulk density in a large container
ISO 1014
09.85 Coke - Determination of true relative density, apparent relative density and
porosity
ISO 2325
02.86 Coke - Size analysis (Nominal top size 20 mm or less)
ISO 18894
04.06 Coke - Determination of coke reactivity index (CRI) and coke strength after
reaction (CSR)
ISO/TC 27/SC 4 Sampling
ISO 5069-1
11.83 Brown coals and lignites - Principles of sampling - Part 1: Sampling for
determination of moisture content and for general analysis
Page 38 of 44
ISO 5069-2
12.83 Brown coals and lignites - Principles of sampling - Part 2: Sample preparation
for determination of moisture content and for general analysis
ISO 9931
12.91 Coal - Sampling of pulverized coal conveyed by gases in direct fire coal systems
ISO 21398
06.07 Hard coal and coke - Guidance to the inspection of mechanical sampling
systems
ISO/TC 27/SC 4/WG 1 Sampling of coal
ISO 13909-1
12.01 Hard coal and coke - Mechanical sampling - Part 1: General introduction
ISO 13909-2
12.01 Hard coal and coke - Mechanical sampling - Part 2: Coal - Sampling from
moving streams
ISO 13909-3
stationary lots
ISO 13909-4
12.01 Hard coal and coke - Mechanical sampling - Part 4: Coal - Preparation of test
samples
ISO/TC 27/SC 4/WG 2 Sampling of coke
ISO 13909-5
12.01 Hard coal and coke - Mechanical sampling - Part 5: Coke - Sampling from
moving streams
ISO 13909-6
12.01 Hard coal and coke - Mechanical sampling - Part 6: Coke - Preparation of test
samples
ISO/TC 27/SC 4/WG 5 Methods for test for bias
ISO 13909-7
12.01 Hard coal and coke - Mechanical sampling - Part 7: Methods for determining the
precision of sampling, sample preparation and testing
ISO 13909-8
12.01 Hard coal and coke - Mechanical sampling - Part 8: Methods of testing for bias
ISO/TC 27/SC 4/WG 6 Sampling of coal seams
ISO 14180
08.98 Solid mineral fuels - Guidance on the sampling of coal seams
ISO/TC 27/SC 4/WG 7 Manual Sampling
ISO 18283
09.06 Hard coal and coke - Manual sampling
ISO 18283:2006/Cor
1
04.09 ISO 18283 Technical Corrigendum 1
ISO/TC 27/SC 4/WG 8 Sampling of coal slurries
ISO 20904
10.06 Hard coal - Sampling of slurries
ISO/TC 27/SC 4/WG 10 Revision of ISO 13909
ISO/DIS 13909-1
07.14 Hard coal and coke - Mechanical sampling - Part 1: General introduction
ISO/DIS 13909-2
moving streams
ISO/DIS 13909-3
stationary lots
ISO/DIS 13909-5
07.14 Hard coal and coke - Mechanical sampling - Part 5: Coke - Sampling from
moving streams
ISO/DIS 13909-6
07.14 Hard coal and coke - Mechanical sampling - Part 6: Coke - Preparation of test
samples
ISO/DIS 13909-7
07.14 Hard coal and coke - Mechanical sampling - Part 7: Methods for determining the
precision of sampling, sample preparation and testing
ISO/DIS 13909-8
07.14 Hard coal and coke - Mechanical sampling - Part 8: Methods of testing for bias
Page 39 of 44
ISO/TC 27/SC 5 Methods of analysis
ISO 12900
06.15 Hard coal - Determination of abrasiveness
ISO/TC 27/SC 5/WG 1 Moisture, volatile matter and ash
ISO 562
06.10 Hard coal and coke - Determination of volatile matter
ISO 579
05.13 Coke - Determination of total moisture
ISO 589
11.08 Hard coal - Determination of total moisture
ISO 687
06.10 Solid mineral fuels - Coke - Determination of moisture in the general analysis
test sample
ISO 1018
11.75 Hard coal - Determination of moisture-holding capacity
ISO 1170
07.13 Coal and coke - Calculation of analyses to different bases
ISO 1171
06.10 Solid mineral fuels - Determination of ash
ISO 11722
07.13 Solid mineral fuels - Hard coal - Determination of moisture in the general
analysis test sample by drying in nitrogen
ISO 17246
06.10 Coal - Proximate analysis
ISO/TC 27/SC 5/WG 2 Carbon, hydrogen, nitrogen, oxygen and sulfur
ISO 157
06.96 Coal - Determination of forms of sulfur
ISO 334
10.13 Solid mineral fuels - Determination of total sulfur - Eschka method
ISO 587
05.97 Solid mineral fuels - Determination of chlorine using Eschka mixture
ISO 609/COR 1
07.96 Solid mineral fuels - Determination of carbon and hydrogen - High temperature
combustion method; Technical corrigendum 1
ISO 609
02.96 Solid mineral fuels - Determination of carbon and hydrogen - High temperature
combustion method
ISO 625/COR 1
07.96 Solid mineral fuels - Determination of carbon and hydrogen - Liebig method;
Technical Corrigendum 1
ISO 625
02.96 Solid mineral fuels - Determination of carbon and hydrogen - Liebig method
ISO 925
05.97 Solid mineral fuels - Determination of carbon dioxide content - Gravimetric
method
ISO 17247
07.13 Coal - Ultimate Analysis
ISO/TS 18806
12.14 Solid mineral fuels - Determination of chlorine content
ISO 19579
10.06 Solid mineral fuels - Determination of sulfur by IR spectrometry
ISO 29541
10.10 Solid minerals fuels - Determination of total carbon, hydrogen and nitrogen
content - Instrumental method
ISO/TC 27/SC 5/WG 7 Brown coal and lignites
ISO 647
11.74 Brown coals and lignites - Determination of the yields of tar, water, gas and
coke residue by low temperature distillation
ISO 975
05.13 Brown coals and lignites - Determination of yield of benzene-soluble extract Semi-automatic method
ISO 1017
12.06 Brown coals and lignites - Determination of acetone-soluble material ("resinous
substance") in benzene-soluble extract
ISO 2950
02.74 Brown coals and lignites - Classification by types on the basis of total moisture
content and tar yield
ISO 5068-1
01.07 Brown coals and lignites - Determination of moisture content - Part 1: Indirect
gravimetric method for total moisture
ISO 5068-2
01.07 Brown coals and lignites - Determination of moisture content - Part 2: Indirect
gravimetric method for moisture in the analysis sample
ISO 5071-1
05.13 Brown coals and lignites - Determination of the volatile matter in the analysis
sample - Part 1: Two- furnace method
Page 40 of 44
ISO 5072
05.13 Hard colas, brown coals and lignites - Determination of true relative density and
apparent relative density
ISO 5073
05.13 Brown coals and lignites - Determination of humic acids
ISO/TC 27/SC 5/WG 8 Major, minor and trace elements in coal and coal residues
ISO 602
04.15 Coal - Determination of mineral matter
ISO 622
08.81 Solid mineral fuels - Determination of phosphorus content - Reduced
molybdophosphate photometric method
ISO 1952
08.08 Solid mineral fuels - Determination of extractable metals in dilute hydrochloric
acid
ISO 11723
11.04 Solid mineral fuels - Determination of arsenic and selenium - Eschka's mixture
and hydride generation method
ISO/DIS 11724
11.15 Solid mineral fuels - Determination of total fluorine in coal, coke and fly ash
ISO 11724
11.04 Solid mineral fuels - Determination of total fluorine in coal, coke and fly ash
ISO/TS 13605
05.12 Solid mineral fuel - Major and minor elements in hard coal ash and coke ash Wavelength dispersive x-ray fluorescence spectrometric method
ISO 15237
12.03 Solid minerals fuels - Determination of total mercury content of coal
ISO/DIS 15237
11.15 Solid minerals fuels - Determination of total mercury content of coal
ISO 15238
12.03 Solid mineral fuels - Determination of total cadmium content of coal
ISO 23380
09.13 Selection of methods for the determination of trace elements in coal
ISO/TC 27/SC 5/WG 9 Guidelines for the validation of methods
ISO 11726
08.04 Solid minerals fuels - Guidelines for the validation of alternative methods of
analysis
ISO/TC 27/SC 5/WG 10 Plastic properties of coal
ISO 349
01.75 Hard coal - Audibert-Arnu dilatometer test
ISO 501
09.12 Hard coal - Determination of the crucible swelling number
ISO 502
06.15 Coal - Determination of caking power - Gray-King coke test
ISO 8264
11.89 Hard coal - Determination of the swelling properties using a dilatometer
ISO 10329
02.09 Coal - Determination of plastic properties - Constant-torque Gieseler
plastometer method
ISO 15585
01.06 Solid mineral fuels - Hard Coal - Determination of caking index
ISO 23873
11.10 Hard coal - Method for the measurement of the swelling of hard coal using a
dilatometer
ISO/TC 27/SC 5/WG 11 On-line analyzers
ISO 15239
04.05 Solid mineral fuels - Evaluation of the measurement performance of on-line
analyzers
ISO/TC 27/SC 5/WG 12 Miscellaneous Methods
ISO 540
05.08 Hard coal and coke - Determination of ash fusibility
ISO 1928
05.09 Solid mineral fuels - Determination of gross calorific value by the bomb
calorimetric method and calculation of net calorific value
ISO 5074
10.15 Hard coal - Determination of Hardgrove grindability index
ISO/TC 27/SC 5/WG 14 Petrographic analysis of coal
ISO/DIS 7404-1
12.15 Methods for the petrographic analysis of coals - Part 1: Vocabulary
ISO 7404-1
10.94 Methods for the petrographic analysis of bitumious coal and anthracite - Part 1:
Vocabulary
Page 41 of 44
ISO 7404-2
10.09 Methods for the petrographic analysis of coals - Part 2: Methods of preparing
coal samples
ISO 7404-3
10.09 Methods for the petrographic analysis of coals - Part 3: Method of determining
maceral group composition
ISO 7404-4
12.88 Methods for the petrographic analysis of bitumious coal and anthracite - Part 4:
Method of determining microlithotype, carbominerite and minerite composition
ISO 7404-5
10.09 Methods for the petrographic analysis of coals - Part 5: Method of determining
microscopically the reflectance of vitrinite
Page 42 of 44
FB Mining ISO/TC 82
ISO/TC 82 Mining
ISO/TC 82 Mining
ISO 610
08.90 High-tensile steel chains (round link) for chain conveyors and coal ploughs
ISO 710-1
09.74 Graphical symbols for use on detailed maps, plans and geological crosssections - Part 1: General rules of representation
ISO 710-2
09.74 Graphical symbols for use on detailed maps, plans and geological crosssections - Part 2: Representation of sedimentary rocks
ISO 710-3
09.74 Graphical symbols for use on detailed maps, plans and geological crosssections - Part 3: Representation of magmatic rocks
ISO 710-4
04.82 Graphical symbols for use on detailed maps, plans and geological crosssections - Part 4: Representation of metamorphic rocks
ISO 710-5
07.89 Graphical symbols for use on detailed maps, plans and geological crosssections - Part 5: Representation of minerals
ISO 710-6
06.84 Graphical symbols for use on detailed maps, plans and geological crosssections - Part 6: Representation of contact rocks and rocks which have
undergone metasomatic, pneumatolytic or hydrothermal transformation or
transformation by weathering
ISO 710-7
08.84 Graphical symbols for use on detailed maps, plans and geological crosssections - Part 7: Tectonic symbols
ISO 721
01.91 Rock drilling equipment - Integral stems
ISO 722
02.91 Rock drilling equipment - Hollow drill steels in bar form, hexagonal and round
ISO 723
02.91 Rock drilling equipment - Forged collared shanks and corresponding chuck
bushings for hollow hexagonal drill steels
ISO 1082
08.90 Mining - Shackle type connector units for chain conveyors
ISO 1717
06.74 Rock drilling - Rotary drill-rods and rotary drill-bits for dry drilling - Connecting
dimensions
ISO 1718
01.91 Rock drilling equipment - Drill rods with tapered connection for percussive drilling
ISO 1721
08.74 Rock drilling - Extension drill-steel equipment for percussive long-hole drilling Reverse-buttress-threaded equipment 1 1/16 and 1 1/14 (27 and 32 mm)
ISO 1722
09.74 Rock drilling - Extension drill-steel equipment for percussive long-hole drilling Reverse-buttress-threaded equipment 1 1/2 to 2 1/2 in (38 to 64 mm)
ISO 3154
06.88 Stranded wire ropes for mine hoisting - Technical delivery requirements
ISO 3155
04.76 Stranded wire ropes for mine hoisting - Fibre components - Characteristics and
tests
ISO 3156
07.76 Stranded wire ropes for mine hoisting - Impregnating compounds, lubricants
and service dressings - Characteristics and tests
ISO 3551-1
07.92 Rotary core diamond drilling equipment - System A - Part 1: Metric units
ISO 3551-2
07.92 Rotary core diamond drilling equipment - System A - Part 2: Inch units
ISO 3552-1
07.92 Rotary core diamond drilling equipment - System B - Part 3: Metric units
ISO 3552-2
07.92 Rotary core diamond drilling equipment - System B - Part 4: Inch units
ISO 5612
08.90 Mining - Scraper bars for chain conveyors
ISO 5613
06.84 Mining - Drive sprocket assemblies for chain conveyors
ISO 5614
06.88 Locked coil wire ropes for mine hoisting - Technical delivery requirements
ISO/TR 8865
12.90 Mining - guidance on methods of verifying dimensions of sprocket assemblies
for chain conveyors
ISO 8866
05.91 Rotary core diamond drilling equipment - System C
ISO 8866/Cor 1
08.91 Rotary core diamond drilling equipment - System C; technical corrigendum 1
ISO 8866/Cor 2
01.92 Rotary core diamond drilling equipment - System C; technical corrigendum 2
Page 43 of 44
FB Mining ISO/TC 82
ISO 10097-1
10.99 Wireline diamond core drilling equipment - System A - Part 1: Metric units
ISO 10097-2
10.99 Wireline diamond core drilling equipment - System A - Part 2: Inch units
ISO 10098
10.92 Wireline diamond core drilling equipment - System CSSK
ISO 10207/Cor 1
04.91 Rock drilling equipment - Rope threaded drill steel equipment for percussive
drilling, nominal sizes 22 mm to 38 mm; technical corrigendum 1
ISO 10207
02.91 Rock drilling equipment - Rope threaded drill steel equipment for percussive
drilling, nominal sizes 22 mm to 38 mm
ISO 10208
02.91 Rock drilling equipment - Left-hand rope threads
ISO/TC 82/WG 2 Continuous surface miners
ISO/DIS 19224
12.15 Continuous surface miner (CSM) - Safety
ISO/TC 82/JWG 5 Joint ISO/TC 82 - ISO/TC 127 WG: Safety of mining and earthmoving mobile machines
working underground
ISO/DIS 19296.2
12.15 Mining and earthmoving machinery - Mobile machines working underground Machine Safety
Page 44 of 44

Register of Mining Standards - FABERG Normenausschuss Bergbau

Transcription

Similar documents

47: A, p. 1. a2

- Deutsches Bergbau

LSA PROFIL

E-Mail - Bezirksregierung Arnsberg

114-94058 - TE Connectivity