Dimension Master Plus

',0(16,21 0$67(5 3/86Š
(Version 2.0)
Ultrasonic Tapeless Measure & Calculator
Off
7
8
9
..
ON
4
5
6
x
Sq
1
2
3
+
/
0
.
=
–
8VHU·V*XLGH
7DEOH RI &RQWHQWV
INTRODUCING THE DIMENSION MASTER PLUS... 3
Background..........................................................4
Key Functions......................................................7
New and Improved Features..............................11
HOW TO USE THE DIMENSION MASTER PLUS..... 16
Taking Accurate Measurements ........................16
Taking a Linear Measurement...........................16
Taking an Area Measurement............................18
Volume Measurements ......................................18
Large Room Measurements ...............................19
Entering Dimensioned Values...........................20
Spacing Calculation – Linear Division Using
the Manual Entry Method .................................21
Converting Feet-Inch- Fractions to Decimal
Feet ....................................................................22
Square Conversions ...........................................22
Area Calculation – Known Dimension .............22
Volume Calculation – Concrete ........................23
Memory Functions.............................................24
APPENDIX ................................................................. 25
Troubleshooting.................................................25
Environmental Conditions.................................26
GERMAN (DEUTCH) ADDENDUM............................ 28
WARRANTY............................................................... 35
³ ' ,0(16,21
0 $67(5 3 /86 Š
Introducing the
Dimension Master Plus
The Dimension Master Plus (v2.0) is a high-tech
measuring tool that uses the latest in ultrasonic
technology. This tapeless measure and calculator
allows you to take quick and accurate measurements with the touch of a button. You can measure
a single room in seconds or a whole building in
minutes. The Dimension Master Plus features include:
• A special Aim Assist™ pointer lamp simplifying
ultrasonic beam alignment,
• A built-in dimensional calculator that allows
calculations and storage of measured values,
• Easy dimensional conversions using the “Convert” function key,
Off
7
8
9
..
ON
4
5
6
x
Sq
1
2
3
+
/
0
.
=
–
8VHU·V *XLGH ³ Background
How It Works
Using a patented TriSensor Technology™, the Dimension Master Plus sends out an inaudible, narrow ultrasonic beam of sound that bounces off the
“target” surface and returns to the unit as an echo.
The Dimension Master Plus then determines how
long the echo took to return and calculates a linear
distance reading, while internally compensating for
variables such as temperature. Unlike other ultrasonic measuring devices, the beam stays extremely
narrow as it travels from the Dimension Master
Plus. This exceptionally narrow beam allows you
to measure through doorways, down corridors and
in crowded rooms or offices for room-to-room
measurements.
To aid in accurate measuring, the Aim Assist™
pointer lamp enables you to pinpoint the center of
the ultrasonic beam, thus avoiding interference
from obstacles or clutter in your path.
³ ' ,0(16,21
0 $67(5 3 /86 Š
Specifications
Power Source
6 Volts - 4 AAA Alkaline
(MN2400) 1.5 volt batteries
Range
18 inches – 60 feet
(0.5m – 18m)
Accuracy
99.5% or better over entire
range
Displayed
Measurement
Resolution
1/4 inch up to 10 feet; 1 inch
beyond 10 feet (6mm up to
3m; 25mm beyond 3m)
Beam Angle
2°
Operating
Temperature
32°F – 100°F
(0°C – 38°C)
Size
5.6 x 3.25 x 0.9 inches
(143 x 84 x 23mm)
Weight
6 ounces (170 grams)
Battery Information
When you first receive your Dimension Master
Plus, you will need to remove the plastic tab sticking out of the battery compartment before you use
it. 4 AAA Alkaline batteries are used to power the
Dimension Master Plus. If a “lo batt” reading appears on the display, the batteries need to be replaced by removing the door on the back of the
unit. The unit will continue to operate for approximately 2 hours after the low battery indication. For
best results, use DURACELL® AAA (MN2400)
batteries.
8VHU·V *XLGH ³ Feet/Inch or Metric Switch
For your convenience, a switch on the left side of
the unit allows you to set the measurement mode to
either the English/Imperial Feet-Inch (F/I) system
or to the Metric (Met) system.
Aim Assist™ Pointer Lamp
The Aim Assist™ pointer lamp is designed for
many years of service under normal operation.
Should the bulb burn out, please contact the manufacturer for replacement details.
Display Accuracy
The Dimension Master Plus has an eleven-digit
display. This is made up of seven digits for the
normal display and four digits for the fractional
display. In a standard calculation, the calculation is
carried out to a 10-digit internal accuracy, and then
rounded to a 7-digit standard display using a 5/4
rounding.
Automatic Shutoff
The Dimension Master Plus is designed to shut itself off after approximately 7 minutes of non-use.
Any value shown on the display is cleared at this
point. All values stored in the memory registers remain unchanged.
None/Error Messages
If the Dimension Master Plus is unable to measure
a distance, two beeps sound and either the word
³ ' ,0(16,21 0 $67(5 3 /86 Š
“none” or “Error” is displayed, depending on the
measurement situation. The unit will also display
“Error” if you make an incorrect entry, try to perform invalid dimensional calculations (i.e., adding
areas and volumes together) or the resulting answer
is beyond the range of the calculator. “Error” will
also appear if you enter a mathematical impossibility, such as division by zero.
There is no need to clear the “none” or “Error”
message. The next valid measurement or keystroke
automatically clears the display. The “none” or
“Error” message will not clear previously stored
values from memory.
Key Functions
[On]
On/Clear Entry Key — Turns power on. Pressed
once clears the last entry and display. Pressing
the measurement button will also turn the unit
on.
[Off]
Off Key — Turns all power off. Clears the display and all values stored in memory (M+).
[÷] [x] [+] [−] [=]
Math Operator Keys — Used for basic math
operations.
[0]-[9] & [•]
Digit Keys — Used for keying in numbers.
8VHU·V *XLGH ³ [Sq]
Square Key — Used with a dimension key (feet,
inches, yards, meters) to label entry as an area or
“square” value (e.g., 10 Square Feet).
[/]
Fraction Bar Key — Used to separate the numerator and denominator when entering fractions. [Rcl] [/] shows current fraction setting
(Default is 1/8”).
[Length]
Length Key — Labels, stores or recalls a dimensioned value or measurement as Length. Entering a non-dimensioned value can result in an error when computing Areas or Widths.
[Width]
Width Key — Labels, stores or recalls a dimensioned value or measurement as Width. Entering
a non-dimensioned value can result in an error
when computing Areas or Widths.
[Height]
Height Key — Labels, stores or recalls a dimensioned value or measurement as Height. Entering a non-dimensioned value can result in an error when computing Areas or Widths.
[LxW]
Area Key — Calculates or recalls area based on
Length and Width. If one of these values is not
entered, “None” displays. Repeated presses toggle through the available units of measure.
³ ' ,0(16,21 0 $67(5 3 /86 Š
[LxWxH]
Volume Key — Calculates or recalls volume
based on Length, Width and Height. If one of
these values is not entered, “None” displays.
Repeated presses toggle through the available
units of measure.
[Yards]
Yards Key — Labels a value as Yards. [Convert] [Yards] converts whole or decimal numbers of a different unit of measure to Yards.
[Feet]
Feet Key — Labels a value as Feet. [Convert]
[Feet] converts whole or decimal numbers of a
different unit of measure to Feet. Successive
presses of [Feet] toggle between Feet-Inch and
Decimal Feet.
[Inch]
Inch Key — Labels a value as Inches. [Convert]
[Inch] converts whole or decimal numbers of a
different unit of measure to Inches. Successive
presses of [Inch] toggle between Decimal and
Fractional Inches.
[Meter]
Meter Key — Labels a value as Meters. [Convert] [Meter] converts whole or decimal numbers of a different unit of measure to Meters.
[Rcl]
Recall Key — Used with other keys to recall
and display stored values or settings.
8VHU·V *XLGH ³ [Convert]
Conversion Key — Converts between units of
measure and accesses secondary functions. Repeated presses scroll through available units of
measure:
Linear: Feet-Inch-Fraction, Decimal Feet, InchFraction, Decimal Inch, Yards and Meters
Square: Square Feet, Square Yards and Square
Meters
Cubic: Cubic Feet, Cubic Yards and Cubic Meters
Additional Functions Using [Convert]
[Convert] used with . . .
[÷] {Square Root} Calculates the square root of
a displayed value.
[x]
{AC} Clears and resets all registers to default
values.
[+]
{π} Displays Pi (π = 3.141593).
[−]
{+/–} Toggles displayed value’s sign (+/–).
[=]
{Mode} Changes and displays Measuring
Beam Mode setting.
[•]
{°F/°C} Displays the ambient temperature. If
the unit is set to English/Imperial (F/I), the
temperature is displayed as °F. If the unit is
set to Metric (Met), the temperature is displayed as °C.
³ ' ,0(16,21 0 $67(5 3 /86 Š
[5]
Tags displayed dimension as a value to be ignored when measuring in a cluttered room.
When activated, “Skip” will be lit in the display.
This mode will be cleared upon power down or
when the On button is pressed twice.
[9]
Used to test the LCD. Lights all display segments.
[M+]
Memory Key — Adds displayed value to the
cumulative memory.
New and Improved Features
The Dimension Master Plus (v2.0) gives you the
following new features:
• Three new “Measuring Beam Modes”
-
Smart Mode
-
Narrow Mode
-
Wide Mode
• A new “Skip” mode which allows you to ignore
an object in your measuring path
• A new, more powerful microprocessor.
• Expanded fractional setting accuracy.
• Expanded storage capacity.
• Easier to read display.
8VHU·V *XLGH ³ Measuring Beam Modes
One of the most important new features of the Dimension Master Plus (v2.0) is the addition of three
different measuring beam modes:
Normal Mode is the default setting and can
be used for most measuring situations.
Narrow Mode is used for higher accuracy
within a confined space (narrow hallways, corridors, etc.) or when there is a need to eliminate interference from surrounding objects (such as bookshelves, lamps, etc.). Since this mode is essentially
using a smaller beam area, this method requires
careful alignment of the measuring beam.
Wide Mode is used when walls are not parallel to one another or the alignment of the measuring beam is difficult. If there are several or large
objects/obstructions in the measuring beam path,
you may have difficulty obtaining accurate measurements using Wide Mode.
[Rcl] [=] displays the current Beam Mode setting.
[Convert] [=] is used the change the setting. The
first press changes to the next Beam Mode setting
and shows it to the left of the LCD display. Repeated presses of the [=] key toggle through the
Beam Mode settings. Press any key, other than [=],
to select a desired Beam Mode once that mode has
been displayed on the LCD display.
³ ' ,0(16,21 0 $67(5 3 /86 Š
Skip Measurement Mode
The “Skip Measurement” mode of the Dimension
Maser Plus allows you to take accurate measurements in a cluttered room, without having to switch
measuring modes. When the Dimension Master
Plus takes a reading from an object in the way of
your target, you can set the unit to ignore this
measurement in future readings by pressing [Convert] then [5]. This ignored value will remain in
memory until [On] is pressed twice, or the unit is
powered down.
Greater Math Accuracy
Equipped with a new, more powerful Integrated
Circuit Chip, the Dimension Master Plus performs
math calculations faster and with more accuracy.
Greater Fractional Accuracy
With the addition of three new fraction denominator settings, greater fractional accuracy can be
achieved. Use the following methods to display the
fraction denominator setting:
Method 1
Press [Rcl] [/] to display the current fraction denominator setting. Press [+] or [−] to scroll through
the settings (1/2”, 1/4”, 1/8”, 1/16”, 1/32”, 1/64”).
Once the desired setting is displayed, press any key,
other than [+] or [–], to “set” your setting selection.
8VHU·V *XLGH ³ Method 2
Use the keystrokes below to select and “set” the desired fraction denominator setting:
KEYSTROKE
SETTING
KEYSTROKE
SETTING
[Convert] [1] 1/16”
[Convert] [2]
1/2”
[Convert] [3] 1/32”
[Convert] [4]
1/4”
[Convert] [6] 1/64”
[Convert] [8]
1/8”*
Note: 1/8” is the default setting. When a fraction
denominator setting other than the default setting of
1/8” is being used, a star (★) will appear on the
display when the unit is turned on.
Fractional Feet-Inch/Decimal Toggle
Now “Fractional Feet-Inch” values can be converted to “Decimal” values and back by pressing
[Convert] and repeatedly pressing the [Feet] or
[Inch] key to toggle between formats.
Greater Storage Allocation
With the addition of extra storage registers, you can
now store [Length], [Width] and [Height] measurements. Once stored, these values can be easily
recalled and used with other measurements when
calculating area and volume.
³ ' ,0(16,21 0 $67(5 3 /86 Š
Expanded Use of [LxW] and [LxWxH] Keys
When area and volume are calculated, the results
are displayed in the last used unit of measure. Repeated presses of the [LxW] or [LxWxH] keys recalculate the results for each available unit of
measure.
Expanded Memory Functions
Your Dimension Master Plus includes the following functions for greater flexibility during use:
Function
Keystroke
Add displayed value to Memory
Display & clear value in Memory
Clear value in Memory,
not the value in display
[M+]
[Rcl] [Rcl]
[Convert] [Rcl]
Subtract displayed value from
value in Memory
[Convert] [−] [M+]
Replace value in Memory
with displayed value
[Convert] [Rcl] [M+]
8VHU·V *XLGH ³ How to Use the
Dimension Master Plus
Taking Accurate Measurements
Be sure to hold the Dimension Master Plus still and
directly parallel to the target area while taking a
measurement. The Dimension Master Plus may
give an inaccurate reading or a none/error message
if it is moved or held at an angle while you are attempting to take a measurement.
Make sure that you hold the Dimension Master
Plus in such a way that your fingers do not cover
the three Ultrasonic Sensors on the front of the unit
or the Thermistor (automatic temperature sensor)
located on the bottom left hand side of the unit. The
Dimension Master Plus must be able to accurately
sense the ambient temperature of the surrounding
environment in order to work properly.
The Dimension Master Plus works best when
aimed at smooth surfaces that easily reflect the ultrasonic measuring beam back to the unit. For example, when aiming the Dimension Master Plus at
a window covered by a curtain, open the curtain to
ensure an accurate measurement.
Taking a Linear Measurement
1.
Place the back of the Dimension Master Plus
on a flat surface parallel to the target area
(e.g., hold the back of the unit against the
wall across from the parallel wall you are
targeting).
³ ' ,0(16,21 0 $67(5 3 /86 Š
2.
Press the “Measure” button (the blue button
on top of the unit) down halfway to activate
the Aim Assist™ pointer lamp.
Note: The Aim Assist™ pointer lamp’s beam
is visible for 35 to 40 ft. If you are measuring in a brightly lit area, the beam may not
be visible. Even so, the narrow beam ensures an accurate measurement.
3.
Press the “Measure” button down completely to take your measurement.
4.
The word “Run” displays while the Dimension Master Plus is measuring. When the
distance has been calculated, a single beep
sounds and the measurement value appears
on the display.
Note: If the Dimension Master Plus is unable to measure the distance, either the word
“none” or “Error” (depending on the
measurement situation) will appear on the
display. Two audible beeps will then sound
alerting you to a measurement problem.
8VHU·V *XLGH ³ Taking an Area Measurement
1.
Measure the length of the room as described
in steps 1-4 above.
2.
When the measurement is displayed, press
[Length] to enter the value.
3.
Measure the width of the room.
4.
When the measurement is displayed, press
[Width] to enter the value.
5.
Press [LxW] to display the area calculation.
Note: There is no need to clear the display
after each measurement. The Dimension
Master Plus automatically clears the display
with each new measurement.
Volume Measurements
To take a volume measurement, follow steps 1-4
shown for area measurement. Take a third measurement and press [Height]. Press [LxWxH] to display the calculated volume. Your measurement is
now displayed in cubic dimensions.
³ ' ,0(16,21 0 $67(5 3 /86 Š
Note: Area and volume measurements can
also be calculated by entering values manually into [Length], [Width] and [Height].
Large Room Measurements
If you want to measure a room beyond the 60-foot
range, take two linear measurements. Stand in the
center of the room and take one measurement in
one direction. Turn around and take a second
measurement in the opposite direction. Follow the
directions below to add both measurements to the
cumulative memory:
1.
Pick a point in the center of the room. In one
direction, take the first measurement towards the
wall. When the measurement is displayed, press
[M+].
2.
In the opposite direction, take the second
measurement to the opposite wall. When the
measurement is displayed, press [M+].
3.
Press [Rcl] [M+] to display the cumulative
total that has been stored in Memory.
8VHU·V *XLGH ³ Entering Dimensioned Values
When entering dimensioned values, enter the largest dimension first; feet before inches, inches before
fractions. Enter fractions by first entering the numerator (value above the line), then press the [/]
key, then the denominator (value below the line).
Note: The first valued dimension entered in a
problem determines the format of the result.
For example:
63 yards + 59 inches =
64.63889 yards
63 meters + 59 inches =
64.499 meters
Dimension Examples
Enter the following dimensions (clear after each
entry):
DIMENSION
KEYSTROKE
DISPLAY
2 feet
2 [Feet]
½ inch
1 [/] 2
2 feet 1 inch
2 [Feet] 1 [Inch]
11 yards
11 [Yards]
11 YDS
15 meters
15 [Meter]
15 METERS
2 FEET
0 ½ INCH
2- 1 FEET INCH
Note: Yards and meters may only be entered
as whole (5 yards) or decimal (5.5 meters)
values, not in combination with feet-inchfractions (5 feet 10-7/16 inches).
³ ' ,0(16,21 0 $67(5 3 /86 Š
Enter the following square dimensions:
DIMENSION
KEYSTROKE
DISPLAY
2 square yards
2 [Sq] [Yards]
2 SQ YDS
120 square feet
120 [Sq] [Feet]
120 SQ FEET
32 square meters
32 [Sq] [Meter]
32 SQ METERS
647 square inches
647 [Sq] [Inch]
647 SQ INCH
Spacing Calculation – Linear Division
Using the Manual Entry Method
An office wall that is 78 feet 6 inches in length
must be divided into 5 equal spaces. Find the length
of each section:
STEP
KEYSTROKE
DISPLAY
Enter dimensions:
78 [Feet] 6 [Inch]
Divide by 5
[÷] 5 [=]
Convert to decimal
feet:
[Convert] [Feet]
Convert to decimal
inches:
[Inch]
78−6 FEET INCH
15−8 3/8 FEET INCH
15.7 FEET
188.4 INCH
8VHU·V *XLGH ³ Converting Feet-InchFractions to Decimal Feet
Convert the following feet-inch-fraction dimensions to decimal feet equivalents:
STEP
KEYSTROKE
DISPLAY
Enter & convert 1
foot 2 inches:
1 [Feet] 2 [Inch]
[Convert] [Feet]
1.166667 FEET
Enter & convert 2
feet 4 inches:
2 [Feet] 4 [Inch]
[Convert] [Feet]
2.333333 FEET
Enter & convert 4
feet 8-1/2 inches:
4 [Feet] 8 [Inch] 1 [/]
2 [Convert] [Feet]
4.708333 FEET
Square Conversions
Convert 144 square feet to all other squared dimensions:
STEP
KEYSTROKE
DISPLAY
Enter dimension
144 [Sq] [Feet]
144 SQ FEET
[Convert] [Inch]
20736 SQ INCH
[Yards]
16 SQ YDS
[Meter]
13.378 SQ METERS
Area Calculation – Known Dimension
Two walls need papering. The ceiling is 8 feet high.
You must find the total length of the two walls for
the room’s total area and quantity of wallpaper. The
length of the first wall is 16 feet 2 inches. The
³ ' ,0(16,21 0 $67(5 3 /86 Š
length of the second wall is 12 feet. What is the total wall length and wall area?
STEP
KEYSTROKE
DISPLAY
Enter length of one
wall:
16 [Feet] 2 [Inch]
Enter into memory:
[M+]
Enter 2nd wall’s
length:
12 [Feet]
Enter into memory:
[M+]
M 12– 0 FEET INCH
Display total wall
length:
[Rcl] [M+]
M 28– 2 FEET INCH
16– 2 FEET INCH
M 16– 2 FEET INCH
12 FEET
M 225.3333 SQ FEET
Multiply by 8 feet for [x] 8 [Feet] [=]
total area:
Volume Calculation – Concrete
You are going to form and pour your own concrete
patio. The patio measurements are as follows: 36
feet 3 inches in length, 11 feet 6 inches in width, 4
inches thick. How many cubic yards of concrete are
needed to pour the patio?
STEP
KEYSTROKE
DISPLAY
Enter patio length
36 [Feet] 3 [Inch]
[Length]
L 36- 3 FEET INCH
Enter patio width
11 [Feet] 6 [Inch]
[Width]
W 11- 6 FEET INCH
Enter patio thickness
4 [Inch] [Height]
Solve for volume
[LxWxH]
H 4 INCH
138.9583 CU FEET
8VHU·V *XLGH ³ Convert to cu. yards
[Convert] [Yards]
5.146605 CU YDS
Memory Functions
Use the [Convert] [−] [M+] keys to subtract from
the Memory:
STEP
KEYSTROKE
Clear calculator:
[On] [On]
Enter values into
memory:
10 [Feet] 5 [Inch] [M+]
5 [Feet] 3 [Inch] [M+]
DISPLAY
0.
M 10- 5 FEET INCH
M 5- 3 INCH
1 [/] 16 [M+]
M 0 1/16 INCH
Display memory
total:
[Rcl] [M+]
M 15− 8 1/16
Subtract 10 feet
from memory:
[10] [Feet] [Convert]
[−][M+]
Display results:
[Rcl] [M+]
FEET INCH
M −10− 0
FEET INCH
M 5− 8 1/16
FEET INCH
Clear calculator:
[Convert] [x]
Note: In addition to [Convert] [x], turning the unit
[Off] will also clear all values stored in Memory.
³ ' ,0(16,21 0 $67(5 3 /86 Š
0.
Appendix
Troubleshooting
Symptom: Erratic operation
Solution:
Check display screen. If there is a “lo
batt” display reading, the batteries
need to be replaced.
Symptom: No response when “On” key is
pressed. The display is blank.
Solution:
Check to make sure the batteries are
installed correctly or replace the batteries.
Symptom: Unit operates, but measurements are
erratic.
Solution:
1) Make sure the unit is parallel to the
surface that is being measured.
2) Check to see if there are objects obstructing the measuring beam.
Note: For technical problems not shown above,
please contact Calculated Industries, Inc.
technical support at 702/885-4975.
8VHU·V *XLGH ³ Environmental Conditions
Temperature — The Dimension Master Plus uses
automatic temperature compensation for ensuring
the consistency of measurements in the temperature
range of 32ºF to 100ºF (0ºC to 38ºC). The response
rate of this circuitry enables you to move between
warm and cold areas and measure with reasonable
accuracy. However, we recommend that you do not
leave your Dimension Master Plus in very cold or
very hot conditions (e.g., sunlight in a car), as the
unit will then require more time to adjust to ambient temperature.
As long as the internal temperature is approximately equal to the ambient temperature, accuracy
is unaffected. It is best to wait a few moments for
the unit’s internal temperature to stabilize to the
ambient temperature. You may compensate for this
by adding 1% of the measured distance for each
10ºF (5.5ºC) that the internal temperature is below
the actual ambient temperature or subtracting 1% of
the measured distance for each 10ºF (5.5ºC) that
the internal temperature is above the actual ambient
temperature.
³ ' ,0(16,21 0 $67(5 3 /86 Š
Humidity and Altitude — Humidity and altitude
can affect the maximum measurement distance and
beam angle of all ultrasonic distance-measuring
tools. As the humidity increases or the altitude decreases, the maximum measurement distance and
beam angle is reduced. As humidity decreases or
the altitude increases, the maximum range and
beam angle is increased.
Therefore on a day with a very low humidity you
are more likely to detect objects over a wider field
of view and at a greater distance.
Outdoor Measurements — The Dimension Master Plus is primarily designed for indoor use. It may
also be used outdoors, provided there is only light
wind. A strong wind will tend to affect the maximum measurement range.
Moisture — Your Dimension Master Plus is a
high precision measuring device that is open to the
atmosphere. For this reason, it should not be used
in conditions (i.e., rain, mist, etc.) where moisture
can get within the unit.
8VHU·V *XLGH ³ German (Deutsch) Addendum
=86$7= =80
',0(16,21 0$67(5 3/86Œ
%(187=(5+$1'%8&+
Off
7
8
9
..
ON
4
5
6
x
Sq
1
2
3
+
/
0
.
=
–
Neue, verbesserte DMP-Tastatur mit Display
Der neue und verbesserte Dimension Master Plus™
von CII bietet viele der beliebtesten Funktionen
unserer Bestseller-Produktreihe Construction
Master®. Vor der erstmaligen Anwendung des
Dimension Master Plus sollten Sie kurz die
folgenden Seiten durchlesen.
³ ' ,0(16,21 0 $67(5 3 /86 Š
Erhöhte Bruchgenauigkeit
Mit den zusätzlichen drei Brucheinstellungen kann
eine höhere Buchgenauigkeit erzielt werden. Der
Nenner kann mit einer der folgenden Methoden
eingestellt werden:
1. Methode
Drücken Sie [Rcl] und [/], um die aktuelle
Brucheinstellung anzuzeigen. Drücken Sie [+] und
[–], um die verfügbaren Optionen anzuzeigen.
Wenn die gewünschte Einstellung angezeigt ist,
drücken Sie eine beliebige andere Taste, um diese
zu wählen.
2. Methode
Drücken Sie die in der folgenden Tabelle gezeigten
Tastenkombinationen, um den entsprechenden
Nenner einzustellen:
Tastenkombination/
Einstellung
Tastenkombination/
Einstellung
[Convert] [1]
1/16
[Convert] [2]
1/2
[Convert] [3]
1/32
[Convert] [4]
1/4
[Convert] [6]
1/64
[Convert] [8]
1/8*
*Standardeinstellung
Umschalten zwischen Bruch- und
Dezimalanzeige von Foot/Inch
Foot/Inch-Werte können jetzt leicht auf
Dezimalwerte bzw. auf Bruchwerte umgerechnet
werden. Mit jedem Drücken der Taste [Feet] wird
zwischen beiden Formaten umgeschaltet.
8VHU·V *XLGH ³ Zusätzliche Meßstrahloptionen
Der neue DMP bietet erweiterte Meßfähigkeiten
durch drei verschiedene Meß(strahl)optionen.
Normaler Modus ist die
Standardeinstellung und kann für die meisten
Meßarbeiten verwendet werden.
Schmaler Modus wird verwendet, wenn
eine hohe Genauigkeit erforderlich ist, oder
wenn Störungen durch periphere
Gegenstände eliminiert werden müssen.
Durch den schmaleren Meßstrahlwinkel muß
bei dieser Methode auf eine sorgfältige
lotgerechte Fluchtung geachtet werden, um
eine genaue Ablesung zu gewährleisten.
Breiter Modus wird verwendet, wenn
Wände nicht parallel zueinander verlaufen,
oder wenn eine Fluchtung des Meßstrahls
schwierig ist. Wenn sich mehrere oder große
Gegenstände im Meßweg befinden, kann es
schwierig sein, eine genaue Ablesung zu
erzielen.
Diese Einstellungen werden durch Drücken der
Tasten [Convert] und [=] vorgenommen. Beim
ersten Tastendruck wird die aktuelle Einstellung
angezeigt. Durch wiederholtes Drücken der Taste
[=] werden die verfügbaren Optionen nacheinander
angezeigt. Um die angezeigte Option zu wählen,
drücken Sie eine beliebige andere Taste.
³ ' ,0(16,21
0 $67(5 3 /86 Š
Höhere mathematische Genauigkeit
Der Dimension Master Plus (DMP) ist mit einem
neuen, leistungsstarken Chip ausgestattet, wodurch
Kalkulationen schneller und mit höherer
Genauigkeit durchgeführt werden.
Erweiterte Funktion der Tasten [Area] und [Volume]
Wenn Fläche und Volumen berechnet werden, wird
das Ergebnis in der zuletzt verwendeten Maßeinheit
angezeigt. Bei jedem erneuten Drücken der [Area]oder [Volume]-Taste wird das Ergebnis in die
nächste verfügbare Maßeinheit umgerechnet.
Erweiterte Speicherfunktionen
DMP bietet jetzt die folgenden Funktionen, die zu
einer gesteigerten Flexibilität bei der Anwendung
beitragen.
Funktion
Tastenkombination
Angezeigten Wert zum gespeicherten Wert addieren
Speicher anzeigen und löschen
[Rcl] [Rcl]
Speicher löschen; nicht die Anzeige
Subtrahiert den angezeigten vom
gespeicherten Wert
Ersetzt den gespeicherten mit
dem angezeigten Wert
[M+]
[Convert] [Rcl]
[Convert] [–] [M+]
[Convert] [Rcl] [M+]
8VHU·V *XLGH ³ Größere Speicherkapazität
Es wurden extra Speicherregister hinzugefügt, in
denen Längen-, Breiten- und Höhenmessungen
gespeichert werden können. Die so gespeicherten
Werte können leicht abgerufen und für andere
Messungen, z.B. zur Berechnung von Fläche und
Volumen, verwendet werden.
Erweiterte Anzeige
Das LCD-Display des DPM wurde erweitert, so
daß mehr Informationen angezeigt und die Zahlen
leichter abgelesen werden können.
Tastaturfunktionen
[Length]
Legt den Wert als Länge fest
[Width]
Legt den Wert als Breite fest
[Height]
Legt den Wert als Höhe fest
Berechnet die Fläche anhand der
[LxW]
eingegebenen Länge und Breite und zeigt das
Ergebnis an. Wurde einer dieser Werte nicht
eingegeben, erscheint "None". Durch
wiederholtes Drücken dieser Taste, wird
zwischen den verfügbaren Maßeinheiten
umgeschaltet.
[LxWxH] Berechnet das Volumen anhand der
eingegebenen Länge, Breite und Höhe. Wurde
einer dieser Werte nicht eingegeben, erscheint
"None". Durch wiederholtes Drücken dieser
Taste, wird zwischen den verfügbaren
Maßeinheiten umgeschaltet.
³ ' ,0(16,21 0 $67(5 3 /86 Š
Wird in Verbindung mit anderen
[Rcl]
Tasten gedrückt, um gespeicherte Werte oder
Einstellungen anzuzeigen.
[Convert] Rechnet zwischen den Maßeinheiten
um und bietet Zugriff auf sekundäre Funktionen.
Durch wiederholtes Drücken werden die
verfügbaren Maßeinheiten angezeigt:
Linear:
Foot/Inch, Foot, Inch, Yard, Meter
Quadrat: Quadrat-Foot, Quadrat-Yard,
Quadratmeter
Kubik:
Kubik-Foot, Kubik-Yard, Kubikmeter
[Yards]
Legt den Wert als Yard-Maß fest.
Legt den Wert als Foot-Maß fest.
[Feet]
Durch Drücken von [Convert] und [Feet] werden
ganze oder Dezimalwerte einer anderen
Maßeinheit in Foot umgerechnet. Dient auch
zum Umschalten zwischen Foot/Inch und
Dezimal-Foot.
Legt den Wert als Inch-Maß fest.
[Inch]
Durch Drücken von [Convert] und [Inch]
werden ganze oder Dezimalwerte einer anderen
Maßeinheit in Inch umgerechnet. Dient auch
zum Umschalten zwischen Dezimal- und
Bruchteilanzeige der Inch.
[÷] [x] [+] [–] [=] [.] Mathematische Operatoren
Legt den Wert als Meter-Maß fest.
[Meter]
Durch Drücken von [Convert] und [Meter]
werden ganze oder Dezimalwerte in DezimalMeter umgerechnet.
8VHU·V *XLGH ³ [M+]
Speichert den angezeigten Wert.
[Sq]
fest.
Legt den Wert als "Quadratwurzel"
[/]
Bruchstrich. Zum Trennen von Nenner
und Zähler. Durch Drücken von [Rcl] und [/]
wird die aktuelle Brucheinstellung angezeigt.
Weitere Funktionen in Verbindung mit der Taste
[Convert]
[Convert] in Verbindung mit . . .
[÷]
berechnet die Quadratwurzel.
löscht alle Werte bzw. setzt diese auf
[x]
die Standardeinstellung zurück.
[+]
zeigt den Pi an (p = 3.141593).
schaltet das Vorsatzzeichen (+/-) des
[–]
angezeigten Wertes um.
[=]
[.]
zeigt die Meßstrahleinstellung an.
zeigt die Temperatur an. Wenn der
Rechner auf ∞F/1" eingestellt ist, wird die
Temperatur in ∞F gemessen. Ist er auf
"Metrisch" eingestellt, werden ∞C angezeigt.
³ ' ,0(16,21 0 $67(5 3 /86 Š
Warranty
Warranty Repair Service – U.S.A.
Calculated Industries, Inc. (“CII”) warrants this
product against defects in materials and workmanship for a period of one (1) year from the date of
original consumer purchase in the U.S. If a defect
exists during the warranty period, CII, at its option,
will either repair (using new or remanufactured
parts) or replace (with a new or remanufactured
unit) the product at no charge.
THE WARRANTY WILL NOT APPLY TO THE
PRODUCT IF IT HAS BEEN DAMAGED BY MISUSE,
ALTERATION, ACCIDENT, IMPROPER HANDLING
OR OPERATION, OR IF UNAUTHORIZED REPAIRS
ARE ATTEMPTED OR MADE. SOME EXAMPLES OF
DAMAGES NOT COVERED BY WARRANTY
INCLUDE, BUT ARE NOT LIMITED TO, BATTERY
LEAKAGE, BENDING, OR VISIBLE CRACKING OF
THE LCD, WHICH ARE PRESUMED TO BE
DAMAGES RESULTING FROM MISUSE OR ABUSE.
To obtain warranty service in the U.S., ship the
product postage paid to the CII Authorized Service
Provider listed on the back page of the User’s
Guide. Please provide an explanation of the service
requirement, your name, address, day phone number and dated proof of purchase (typically a sales
receipt). If the product is over 90 days old, include
payment of $6.95 for return shipping and handling
within the contiguous 48 states. Outside the contiguous 48 states, please call CII for return shipping
costs.
8VHU·V *XLGH ³ A repaired or replacement product assumes the remaining warranty of the original product or 90
days, whichever is longer.
Non-Warranty Repair Service – U.S.A.
Non-warranty repair covers service beyond the
warranty period or service requested due to damage
resulting from misuse or abuse. Contact the CII
Authorized Service Provider listed on the back
page of the User’s Guide to obtain current product
repair information and charges. Repairs are guaranteed for 90 days.
Repair Service – Outside the U.S.A.
Not all countries have CII Authorized Service Providers or the same warranty and service policies. To
obtain warranty or non-warranty repair service for
goods purchased outside the U.S., contact the
dealer through which you initially purchased the
product. If you cannot reasonably have the product
repaired in your area, you may contact CII to obtain
current product repair information and charges, including freight and duties.
Calculated Industries, Inc.
4840 Hytech Drive
Carson City, NV 89706 U.S.A
Tel: 775/885-4975 • Fax: 775/885-4949
http://www.calculated.com • techsupport@calculated.com
³ ' ,0(16,21 0 $67(5 3 /86 Š
Disclaimer
CII MAKES NO WARRANTY OR REPRESENTATION,
EITHER EXPRESS OR IMPLIED, WITH RESPECT TO
THE PRODUCT’S QUALITY, PERFORMANCE,
MERCHANTABILITY, OR FITNESS FOR A
PARTICULAR PURPOSE. AS A RESULT, THIS
PRODUCT, INCLUDING BUT NOT LIMITED TO,
KEYSTROKE PROCEDURES, MATHEMATICAL
ACCURACY AND PREPROGRAMMED MATERIAL, IS
SOLD “AS IS,” AND YOU THE PURCHASER ASSUME
THE ENTIRE RISK AS TO ITS QUALITY AND
PERFORMANCE.
IN NO EVENT WILL CII BE LIABLE FOR DIRECT,
INDIRECT, SPECIAL, INCIDENTAL, OR
CONSEQUENTIAL DAMAGES RESULTING FROM
ANY DEFECT IN THE PRODUCT OR ITS
DOCUMENTATION.
The warranty, disclaimer, and remedies set forth
above are exclusive and replace all others, oral or
written, express or implied. No CII dealer, agent or
employee is authorized to make any modification,
extension or addition to this warranty.
Some states do not allow the exclusion or limitation
of implied warranties or liability for incidental or
consequential damages, so the above limitation or
exclusion may not apply to you. This warranty
gives you specific rights and you may also have
other rights which vary from state to state.
FCC Class B
This equipment has been certified to comply with
the limits for a Class B computing device, pursuant
to Subpart J of Part 15 of FCC rules.
8VHU·V *XLGH ³ Looking for New Ideas
Calculated Industries, Inc. (CII), a leading manufacturer of special function calculators and digital
measuring instruments, is always looking for new
product ideas in these areas.
If you have one or if you have any suggestions for
improvements to this product or its User’s Guide,
please call or write our Product Development Department. Thank you.
Calculated Industries, Inc.
Attn: Product Development
4840 Hytech Drive
Carson City, NV 89706 U.S.A
Tel: 775/885-4975 • Fax: 775/885-4949
http://www.calculated.com • techsupport@calculated.com
³ ' ,0(16,21 0 $67(5 3 /86 Š
NOTE
8VHU·V *XLGH ³ TriSensor Technology
and Aim Assist Pointer Lamp
are trademarks of Calculated Industries, Inc.
Dimension Master Plus
and Calculated Industries®
are registered trademarks of
Calculated Industries, Inc.
ALL RIGHTS RESERVED
Duracell is a registered trademark of Duracell Inc.
U.S. Patent #4,953,141
Calculated Industries, Inc.
4840 Hytech Drive
Carson City, NV 89706 U.S.A
Phone: 775/885-4975 • Fax: 775/885-4949
Web: http://www.calculated.com • E-Mail: info@calculated.com
Designed in the U.S. by Calculated Industries, Inc.
1998, Calculated Industries, Inc.
Manual 3302-MN-A
Printed in Taiwan, DMP-MAN v2.0