CNC Router Tooling and Accessories

CNC Router Tooling and Accessories
2008
• Collet Chucks
• Drill Chucks
• Arbors
• Shrink Fit
• Collets
• Pull Studs
• Set-up Tools
• Aggregates
see page 38…
Because your router’s performance
depends on high-precision tooling.
Techniks Certified Tooling Improves Router Performance
Every holder is individually tested for quality & accuracy and comes with
a lab certification documenting accuracy and balance specifications.
Techniks Certified = High Performance Tooling = Best T.I.R.
Lab Certified Accuracy
Taper-to-Pocket T.I.R. 0.0001"
Power Coat Nuts
Measured from taper O.D.
to collet pocket I.D.
Our Power Coat nut holds
40% tighter than bearing nuts
for best T.I.R. and rigidity.
Each tool holder is lab
certified for accuracy
and balance.
Ultra Precision Collet
Each collet hand inspected.
T.I.R. only 0.0002"
Taper Accuracy AT3
Taper ground to AT3 accuracy for
maximum contact with spindle.
Balanced to 24,000 RPM
Balanced Nut
Factory balanced to
24,000 RPM at G2.5
Custom balancing to
60,000 RPM available.
Balanced nut reduces
vibration to extend
cutting tool life.
Use Techniks Certified Tooling for improved cutting and extended tool life.
Each Tool Individually Lab Certified
How T.I.R. Affects Cutting Tool LIfe
T.I.R. (total indicator runout) is the measure
of concentricity of the cutting tool in the tool
holder. T.I.R. is measured in "tenths" or oneten-thousandths of an inch.
Cutting tool life decreases by
10% for every .0001" T.I.R. The
rigidity and accuracy of Techniks
tool holders minimizes T.I.R.
Tool holders make
the important connection between the
machine spindle and
the cutting tool.
Quality tool holders
extend tool life by
150% or more.
A full report comes with each tool.
Percent Tool Life
200
150
100
50
0
0
2
4
6
8
T.I.R. in tenths
10
Every .0001" T.I.R. loses 10% tool life
Table of Contents
Tool Holders
COLLET CHUCKS
Tool Holders
DRILL CHUCKS &
ADAPTERS
Collets & Nuts
COLLETS
ER Inch Collets ................... 14
ER Metric Collets ................ 15
TG Collets ............................20
TG Nuts ................................21
HP3 High Precision ...........9
Drill Adapters ....................9
HSK F and HSK E ................4
ISO 20 and ISO 30 ................5
SK 30 .....................................5
BT 30 ......................................6
BT 35 ......................................7
ER Straight Shank Ext .........7
SHRINK FIT HOLDERS
Shoda Collets ......................22
Perske DIN 6388 Collets ....23
DNA Collets .........................24
Retention Knobs .................25
Setup Equipment
DUST SEALS, WIPERS
Dust Seals (internal) ...........26
Dust Covers (external) .......27
Spindle Wipers ....................27
WRENCHES & GAUGES
Hand Wrenches ..................28
Torque Wrenches ...............29
Torque Wrench Adapters ..29
Tightening Fixtures ............30
Digital Height Gauge ..........31
Analog Axial Gauge ............31
Aggregate Heads
AGGREGATE
HEADS
HSK 63F ........................ 10
ISO 30 ............................. 10
Shrink Fit Machines ......11
CMS Tool Holder ...................9
COLLET NUTS
HYDRAULIC HOLDERS
ARBOR TOOL HOLDERS
Power Coat ER Nuts........... 16
ER Bearing Nuts .................18
HSK 63F................................8
ISO 30 ..................................8
ER High Speed Mini............18
Dust Cover Nuts (ER) ........19
Dust Cover Nut (TG) ...........21
Shoda Nuts ..........................22
Perske DIN 6388 Nuts ........23
HSK Hydraulics ................ 12
ISO Hydraulics ................. 12
Reducing Sleeves ........... 13
About our aggregates .......33
Single output (Mono).........34
Double output (Duo) ..........35
Quad output (Quattro) .......36
Variable angle (Vario) ........37
Floating head (Soft-Touch 38
Light weight (Smart Line) 39
Output options ...................40
Other Info
Special Orders.....................42
Part Number Index..............44
Call us toll free: (800) 597-3921, Local: (317) 803-8000, Fax: (317) 803-8001, Email: info@techniksusa.com
HSK 63F and HSK E Collet Chucks for CNC Routers
• Balanced to 24,000 RPM at G2.5
flats
• Inspection report included for
accuracy and balance
D
N
• includes collet nut
F
A
Note: Measure the "A" dimension with the collet in the nut.
Dimensions are in millimeters.
HSK 63F Tool Holders
Part No.
Description
D
A
F
N
Collet Nut
Wrench
Flats
171.05.008.001
HSK 63F x ER 16 - 60*
63
60
26
32
46116
04613
26
171.05.008.002
HSK 63F x ER 16 - 100*
63
100
26
32
46116
04613
26
30000
HSK 63F x ER 32 - 70
63
70
26
50
46132
04616
36
30001
HSK 63F x ER 40 - 76
63
76
26
63
46140
04617
46
30002
HSK 63F x ER 40 - 90
63
90
26
63
46140
04617
46
30005
HSK 63F x ER 40 - 125
63
125
26
63
46140
04617
46
31025F
HSK 63F x SYOZ 25 - 80
63
80
26
60
03638
03691
38
*Use with DNA ER 16 collets and nuts for best rigidity and accuracy (T.I.R.) when using cutting tools 6mm and smaller. See page 24
• Balanced to 25,000 RPM at G2.5
• Inspection report included for
accuracy and balance
flats
• includes collet nut
��
��
��
Note: Measure the "l1" dimension with the collet in the nut.
Dimensions are in millimeters.
HSK 32E, 40E, 50E, 63E Tool Holders for HSK E type spindle
Part No.
Description
D
d1
l1
l2
Collet Nut
Wrench
Flats
31374-60
HSK 32E x ER 25
32
32
48
27
46125
04615
22
84.05.008.001
HSK 40E x ER 16 - 65*
40
28
65
45
46116
04613
24
84.05.008.002
HSK 40E x ER 25 - 75
40
42
75
55
46125
04615
27
84.05.008.003
HSK 40E x ER 32 - 100
40
50
100
80
46132
04616
35
85.05.008.002
HSK 50E x ER 32 - 85
50
50
85
59
46132
04616
36
86.05.008.002
HSK 63E x ER 32 - 90
63
50
90
64
46132
04616
none
86.05.008.003
HSK 63E x ER 40 - 120
63
63
120
94
46140
04617
none
50001
HSK 63E x ER 40 - 75
63
63
75
49
46140
04617
none
*Use with DNA ER 16 collets and nuts for best rigidity and accuracy (T.I.R.) when using cutting tools 6mm and smaller. See page 24
4
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.
ISO and SK Tool Holders for CNC Routers
• Balanced to 25,000 RPM at G2.5
• Inspection report included for
accuracy and balance
• includes collet nut
flats
ISO 30
ISO 20
Note: Measure the "A" dimension with the collet in the nut.
Dimensions are in millimeters.
ISO 20, 30, and 40 Tool Holders
Part No.
Description
D
A
F
N
Collet Nut
Wrench
Flats
06000-2016M
ISO 20 x ER 16M - 52 w/HS mini nut & stud*
*30
52
15.9
22
33116
04622
17
06000-2016MC
ISO 20 x ER 16 - 52 coated HS mini nut & stud*
30
52
15.9
22
53116
04622
17
06000-2516
ISO 20 x ER 16 - 52*
30
52
15.9
32
46116
04613
17
06000-2520
ISO 20 x ER 20 - 52
30
52
15.9
35
46120
04614
17
12407-W
ISO 30 x ER 11M - 100
50
100
15.9
16
23111
04621
14
12000-CMS
ISO 30 x ER 32 - CMS
46
58
15.9
50
46132
04616
36
12213-W-50
ISO 30 x ER 32 - 50
50
50
15.9
50
46132
04616
47
12213-W-63
ISO 30 x ER 32 - 63
50
63
15.9
50
46132
04616
36
12213-W-90
ISO 30 x ER 32 - 90
50
90
15.9
50
46132
04616
36
12215-W-57
ISO 30 x ER 40 - 57
50
57
15.9
63
46140
04617
47
12040-CMS
ISO 30 x ER 40 - CMS w/o nut
46
66
15.9
63
46140
04617
42
12261-W
ISO 40 x ER 40 - 70mm
63.5
70
15.9
63
46140
04617
46
*Use with DNA ER 16 collets and nuts for best rigidity and accuracy (T.I.R.) when using cutting tools 6mm and smaller. See page 24.
• Balanced to 25,000 RPM at G2.5
• Inspection report included for
accuracy and balance
flats
• includes collet nut
Note: Measure the "A" dimension with the collet in the nut.
Dimensions are in millimeters.
SK Tool Holders for ANDI and Weeke CNC Routers
Part No.
Description
D
A
F
N
Collet Nut
Wrench
Flats
NT-54300130
SK-30 x SYOZ 25 - 70
50
70
15.9
60
included
03691
38
All Techniks products are backed by our 100% satisfaction guarantee!
5
BT 30 Tool Holders for CNC Routers
• Balanced to 25,000 RPM at G2.5
• Inspection report included for
accuracy and balance
Note: Measure the "A" dimension with the collet in the nut.
Dimensions are in millimeters unless otherwise noted.
BT 30, ER 16 Tool Holders*
Part No.
Description
D
A
F
N
Collet Nut
Wrench
06101
BT 30 x ER 16 - 70 with hex nut
46
70
20
28
41116
04609
06101-SLOTNUT
BT 30 x ER 16 - 70 with slotted nut
46
70
20
32
46116
04613
06102
BT 30 x ER 16 - 60 with hex nut
46
60
20
28
41116
04609
06102-C
BT 30 x ER 16 - 60 with dust seal nut
46
60
20
32
41616
04609
06102-DNA
BT 30 x ER 16 - 60 with DNA 16 nut
46
60
20
27
27116
DNA16W
06102-SLOTNUT
BT 30 x ER 16 - 60 with slotted nut
46
60
20
32
46116
04613
06103
BT 30 x ER 16 - 90 with hex nut
46
90
20
28
41116
04609
06103-SLOTNUT
BT 30 x ER 16 - 90 with slotted nut
46
90
20
32
46116
04613
06104
BT 30 x ER 16 - 100 with hex nut
46
100
20
28
41116
04609
06104-SLOTNUT
BT 30 x ER 16 - 100 with slotted nut
46
100
20
32
46116
04613
06105
BT 30 x ER 16 - 120 with hex nut
46
120
20
28
41116
04609
06105-SLOTNUT
BT 30 x ER 16 - 120 with slotted nut
46
120
20
32
46116
04613
*Use with DNA ER 16 collets and nuts for best rigidity and accuracy (T.I.R.) when using cutting tools 6mm and smaller. See page 24.
BT 30, ER 20 Tool Holders
Part No.
Description
D
A
F
N
Collet Nut
Wrench
06106
BT 30 x ER 20 - 70
46
70
20
34
41120
04610
06106-SLOTNUT
BT 30 x ER 20 - 70 with slotted nut
46
70
20
35
46120
04614
06107
BT 30 x ER 20 - 135
46
135
20
35
41120
04614
06107-SLOTNUT
BT 30 x ER 20 - 135 with slotted nut
46
135
20
35
46120
04614
06108-2.5
BT 30 x ER 20 - 2.5"
46
63.5
20
34
41120
04610
06108-2.5-SLOTNUT
BT 30 x ER 20 - 2.5" with slotted nut
46
63.5
20
35
46120
04614
BT 30 ER 25 Tool Holders
6
Part No.
Description
D
A
F
N
Collet Nut
Wrench
06109
BT 30 x ER 25 - 70
46
70
20
42
41925
04615
06110
BT 30 x ER 25 - 60
46
60
20
42
41925
04615
06111
BT 30 x ER 25 - 135
46
135
20
42
41925
04615
06111-90
BT 30 x ER 25 - 90
46
90
20
42
41925
04615
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.
BT 30 and BT 35 Tool Holders and ER Extensions
BT 30, ER 32 Tool Holders
Part No.
Description
D
A
F
N
Collet Nut
Wrench
06112
BT 30 x ER 32 - 60
46
60
20
50
46132
04616
06113
BT 30 x ER 32 - 70
46
70
20
50
46132
04616
06113-W-60
BT 30 x ER 32 - 60, 41mm flats - Komo
46
60
20
50
46132
04616
06113-W-60-A
BT 30 x ER 32 - 60 w/nut & stud, 41mm flats - Komo
46
60
20
50
46132
04616
06113-W-90
BT 30 x ER 32 - 90 38mm flats - Komo
46
90
20
50
46132
04616
06114
BT 30 x ER 32 - 100
46
100
20
50
46132
04616
06115
BT 30 x ER 40 - 80
46
80
20
63
46132
04616
BT 30, SYOZ 25 Tool Holders
Part No.
Description
D
A
F
N
Collet Nut
Wrench
06001-W
BT 30 x SYOZ 25 - 70, 38mm flats - Komo
46
70
20
60
included
03691
06001
BT 30 x SYOZ 25 - 70 with nut
46
70
20
60
included
03691
BT 35, ER 32, SYOZ 25 Tool Holders for Heian Routers
Part No.
Description
D
A
F
N
Collet Nut
Wrench
06010
BT 35 x SYOZ 25 - 76 with nut
53
76
22
60
included
03691
061-BT35-ER 32 76
BT 35 x ER 32 - 76
53
76
22
50
46132
04616
061-BT35-ER 32 76A
BT 35 x ER 32 - 76 with nut
53
76
22
50
included
04616
• Works with any tool holder
• Precision ground pocket
• Includes ER mini nut - 0rder
high-speed mini nuts pg. 18
l3
set screw – T
C
d
For applications where the extension is rotating, extension length should not exceed a
4:1 ratio Example: 1/2" shank should not extend more than 2" in front of the holder.
l1
Part No.
l2
L
ER 8, 11, 16, 20, 25 Straight Shank Extensions
D
Dimensions are in millimeters unless otherwise indicated.
C
d
I1
L
I2
I3
D
Set Screw
Wrench
Nut Type
04889
3/8"
ER 8M
100
124
24
6
12
-
04620
M
04891
1/2"
ER 11M
140
166.5
26.5
6.6
16
-
04621
M
04893
5/8"
ER 11M
140
158.5
18.5
6.6
16
-
04621
M
04895
1/2"
ER 16M
140
177
37
10.6
22
-
04622
M
04896
3/4"
ER 16M
140
165
25
10.6
22
06083
04622
M
04894
3/4"
ER 20M
140
180
40
11.5
28
06083
04623
M
04897
1"
ER 20M
140
168
28
11.5
28
06083
04623
M
04898
3/4"
ER 25M
100
140
40
12
35
06087
04624
M
04888
1"
ER 25M
140
190
50
12
35
06087
04624
M
Special sizes made to your specifications. See page 42 or call for more information.
7
HSK 63F and ISO 30 Arbors for CNC Routers
• Special 3 screw design improves safety
• Precision ground taper provides high accuracy
• Balanced 25,000 RPM at G2.5
HSK 63F Arbors
Dimensions are in millimeters unless otherwise indicated.
Part No.
Description
D
L
N
B
GL
41060
HSK 63F 1-1/4" arbor x 55
1 1/4"
55
42
20
45
41080-3H
HSK 63F 1-1/4" arbor x 80
1 1/4"
80
42
20
45
41085
HSK 63F 1-1/4" arbor x 100
1 1/4"
100
42
20
45
41087
HSK 63F 1-1/4" arbor x 112
1 1/4"
112
42
20
45
• Special 3 screw design improves safety
• Taper ground to AT3 specification for accuracy
• Balanced 25,000 RPM at G2.5
ISO 30 Arbors
Dimensions are in millimeters unless otherwise indicated.
Part No.
Description
L
GL
D
B
N
12700-40-W
ISO 30 x 1-1/4" x 40 arbor
40
42
1-1/4"
20
42
12700-55-W
ISO 30 x 1-1/4" x 55 arbor
55
42
1-1/4"
20
42
12700-80-W
ISO 30 x 1-1/4" x 80 arbor
80
42
1-1/4"
20
42
12700-100-W
ISO 30 x 1-1/4" x 100 arbor
100
42
1-1/4"
20
42
Special sizes made to your specifications. Refer to page 42 or call for details.
8
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.
High Precision Drill Chucks, Adapters, & CMS Tool Holder
• Capacity from 1/16" to 1/2"
• 4 times greater holding power
• Balanced to 10,000 RPM
Our high-precision drill chucks have the flexibility
to hold a wide range of shank sizes and deliver
superior performance too. Maximum runout
(T.I.R.) is only .0008”. The one-piece design
provides greater rigidty and safety because the
chuck cannot break free during operation.
Part No.
Description
Dimensions are in millimeters
unless otherwise indicated.
d1
I1
G
171.05.046.003
HSK 63F HP3 drill chuck 1/2"
50
123.5
-
64.05.046.051
ISO 30 HP3 drill chuck 1/2"
50
103
M12
67.05.046.001
BT 30 HP3 drill chuck 1/2"
50
92.5
M12
39.05.046.001
BT 40 HP3 drill chuck 1/2"
50
95.5
M16
HP3 Precision Drill Toolholders (ISO, BT, HSK)
• Eliminate threaded drill bits
• Better rigidity and holding power
• Longer drill life
Drill Adapters
Dimensions are in millimeters unless otherwise indicated.
For CNC routers with inline multi-spindles.
Part No.
Collet Type
Shank
Thread
00316-R
ER16
3/8" or 10mm
Right
00316-L
ER16
3/8" or 10mm
Left
Part No.
Shank
Thread
I.D.
00316-SLN-R
M10x1.05
Right
10
00316-SLN-L
M10x1.05
Left
10
• Works with ER or ETS collets
• 0.0002" T.I.R. (collet pocket runout)
Turret Nut
• Taper ground to AT3 specification
CMS Toolholder
Includes turret nut. Order collets and nuts separately.
Part No.
Description
CMS-RR32
CMS Toolholder with turret nut
Special sizes made to your specifications. See page 42 or call for more information.
9
HSK 63F and ISO 30 Shrink-Fit Tool Holders for CNC Routers
• Balanced to 24,000 RPM at G2.5
• Runout (T.I.R.) only .0001"
• Highest rigidity – extends cutter life
Shrink-fit toolholders provide concentric clamping force of 10,000 lbs
or more directly on the tool shank. This is why T.I.R. is so low and
operators are able to run faster and cutters last longer too.
HSK 63F Shrink-Fit Toolholders
Part No.
Dimensions are in millimeters unless otherwise indicated.
Description
d1
d2
d3
I1
I2
171.05.071.010
HSK 63F x 20 - 100
20
33
42
100
52
171.05.071.011
HSK 63F x 25 - 115
25
44
53
115
63
171.05.071.250
HSK 63F x 1/4" - 80
1/4"
21
27
80
36
171.05.071.375
HSK 63F x 3/8" - 95
3/8"
24
32
95
42
171.05.071.500
HSK 63F x 1/2" - 95
1/2"
24
32
95
47
TE-171.05.071.500-S
HSK 63F x 1/2" - 95 Thermwood
1/2"
24
32
95
47
171.05.071.750
HSK 63F x 3/4" - 100
3/4"
33
42
100
52
171.05.072.1
HSK 63F x 1" - 115
1"
44
53
115
53
• Balanced to 24,000 RPM at G2.5
• Runout (T.I.R.) only .0001"
• Highest rigidity – extends cutter life
ISO 30 Shrink-Fit Toolholders
Dimensions are in millimeters unless otherwise indicated.
Part No.
Description
d1
d2
d3
I1
l2
64.05.071.250
ISO 30 x 1/4" - 80
1/4"
18
27
80
39
64.05.071.375
ISO 30 x 3/8" - 80
3/8"
24
32
80
-
64.05.071.500
ISO 30 x 1/2" - 80
1/2"
28
32
80
25
TE-64.05.071.500-S
ISO 30 x 1/2" - 80 Thermwood
1/2"
28
32
80
-
64.05 071.625
ISO 30 x 5/8” - 80
5/8"
28
32
80
50
64.05 071.750
ISO 30 x 3/4" - 80
3/4"
36
41
80
-
TE-64.05 071.750-S
ISO 30 x 3/4" - 80 Thermwood
3/4"
33
41
80
-
10
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.
TechnoSHRINK Induction Heat Shrink-Fit Machines
• Heats and cools automatically
• Eliminates handling hot tools!
• For shank sizes 1/8" to 1-1/4"
Both the TechnoSHRINK
machines feature fast, safe,
induction heat and automatic
cooling using your shop air.
Cycle time is automatically set
by entering the shank size.
Change tools in seconds and
cools in minutes.
Controls are easy to use and do
not require special training.
TechnoSHRINK II
(affordable induction unit
for carbide shanks)
TechnoSHRINK Ultra (for carbide and steel shanks)
Comes with everything you see in this photo.
TechnoSHRINK Machines
Part No.
Description
Tool Change
Cooling
Power Rating
LxDxH
Ship Wt.
00300
Techno-Shrink II
30 seconds
air (2-3 min.)
220V, 1 phase
16"x 19"x 28"
33 lbs
00100
Techno-Shrink Ultra
6-9 seconds
air (2-3 min.)
220V, 3 phase
16"x 16"x 32"
77 lbs
Replacement Parts
Figure 2
Figure 1
Induction Stop Rings
Tool Holder Sleeve
Tool Holder Spindle Adapters
Part No.
Fits Shank Size
Part No.
Spindle
Figure
00165
3mm - 5mm
00151
any 30 taper
2
00166
6mm - 12mm
00152
any 40 taper
1
00167
14mm - 20mm
00153
any 50 taper
1
00168
25mm - 32mm
00156
HSK 32
2
00157
HSK 40
2
00158
HSK 50
2
00159
HSK 63
1
00160
HSK 80
1
Part No.
Description
00170
Use with adapters (left)
Supports holder during shrinking
All Techniks products are backed by our 100% satisfaction guarantee!
11
Hydraulic Tool Holders for CNC Routers
• High holding power, comparable to shrink-fit
• Fast tool changes, simply turn the screw
• Extends tool life of carbide and diamond tooling
To use smaller shank
sizes and odd shank
diameters order reducing sleeves to fit your
cutting tools.
HSK Hydraulic Chucks for CNC Routers
Dimensions are in millimeters unless otherwise indicated.
Part No.
Description
d1
d2
d3
d
I2
I1
171.05.036.016
HSK 63 F Hydro Chuck 20mm ID
20
42
50
63
58
100
171.05.036.018
HSK 63 F Hydro Chuck 32mm ID
32
60
50
63
59
125
171.05.036.020
HSK 63 F Hydro Chuck 25mm ID
25
44
50
63
23
85
171.05.036.035
HSK 63 F Hydro Chuck 1" ID
1.0"
44
50
63
23
85
• High holding power, comparable to shrink-fit
• Fast tool changes, simply turn the screw
• Extends tool life of carbide and diamond tooling
ISO Hydraulic Chucks for CNC Routers
Part No.
Description
Dimensions are in millimeters unless otherwise indicated.
d1
d2
d3
d
I2
I1
64.05.043.224
ISO/SK 30 Hydro Chuck 3/4" ID
3/4"
70
45
50
44
60
64.05.043.225
ISO/SK 30 Hydro Chuck 1" ID
1.0"
70
45
50
44
60
12
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.
Reducing Sleeves for Hydraulic Tool Holders
• Inch and Metric sizes
• T.I.R. only .00012"
• Fast tool changes
L
Inch OD / Inch ID
Dimensions are in millimeters unless otherwise indicated.
Part No.
Description
d1
D
D1
L
L1
L2
05.024.130
3/4" OD - 1/8" ID
0.125"
0.750"
0.945"
2.083"
2.003"
0.079"
05.024.131
3/4" OD - 3/16" ID
0.1875"
0.750"
0.945"
2.083"
2.003"
0.079"
05.024.132
3/4" OD - 1/4" ID
0.25"
0.750"
0.945"
2.083"
2.003"
0.079"
05.024.133
3/4" OD - 5/16" ID
0.3125"
0.750"
0.945"
2.083"
2.003"
0.079"
05.024.134
3/4" OD - 3/8" ID
0.375"
0.750"
0.945"
2.083"
2.003"
0.079"
05.024.135
3/4" OD - 7/16" ID
0.4375"
0.750"
0.945"
2.083"
2.003"
0.079"
05.024.136
3/4" OD - 1/2" ID
0.5"
0.750"
0.945"
2.083"
2.003"
0.079"
05.024.137
3/4" OD - 5/8" ID
0.625"
0.750"
0.945"
2.083"
2.003"
0.079"
d1
D
D1
L
L1
L2
Metric OD / Inch ID
Part No.
Description
05.024.114
20mm OD - 1/4" ID
0.25"
20
24
52.9
50.9
2
05.024.116
20mm OD - 5/16" ID
0.3125"
20
24
52.9
50.9
2
05.024.118
20mm OD - 3/8" ID
0.375"
20
24
52.9
50.9
2
05.024.120
20mm OD - 7/16" ID
0.4375"
20
24
52.9
50.9
2
05.024.122
20mm OD - 1/2" ID
0.5"
20
24
52.9
50.9
2
05.024.126
20mm OD - 5/8" ID
0.625"
20
24
52.9
50.9
2
Metric OD / Metric ID
Part No.
Description
d1
D
D1
L
L1
L2
05.024.001
20mm OD - 6mm ID
6
20
24
52.9
50.9
2
05.024.002
20mm OD - 8mm ID
8
20
24
52.9
50.9
2
05.024.003
20mm OD - 10mm ID
10
20
24
52.9
50.9
2
05.024.004
20mm OD - 12mm ID
12
20
24
52.9
50.9
2
05.024.005
20mm OD - 14mm ID
14
20
24
52.9
50.9
2
05.024.006
20mm OD - 16mm ID
16
20
24
52.9
50.9
2
05.024.012
32mm OD - 10mm ID
10
32
40
66
62
4
05.024.013
32mm OD - 12mm ID
12
32
40
66
62
4
05.024.014
32mm OD - 14mm ID
14
32
40
66
62
4
05.024.015
32mm OD - 16mm ID
16
32
40
66
62
4
05.024.016
32mm OD - 18mm ID
18
32
40
66
62
4
05.024.018
32mm OD - 20mm ID
20
32
40
66
62
4
05.024.020
32mm OD - 25mm ID
25
32
40
66
62
4
All Techniks products are backed by our 100% satisfaction guarantee!
13
ER Precision Inch Collets
• Runout (T.I.R.) only .0002"
• Collapse range: 0.039"
• Collet sets available
Call to order collet sets.
Our ER collets are the best in the industry. They are made from high-carbon
bearing steel that is heat-treated for improved flexibility and longer life. Each
collet is precisely ground and honed using a swiss technique, then individually inspected and tested for quality. Compatible with DR, RD, ESX, AR, & BR
series collets. For best rigidity and cutter life use Power Coat nuts (pg 17).
ER Precision Collets Inch Size
ER 11
ER 16
04211 - 1/16
04216 - 1/16
04211 - 3/32
04216 - 3/32
04220 - 3/32
04225 - 3/32
04232 - 3/32
04211 - 1/8
04216 - 1/8
04220 - 1/8
04225 - 1/8
04232 - 1/8
04211 - 5/32
04216 - 5/32
04220 - 5/32
04225 - 5/32
04211 - 3/16
04216 - 3/16
04220 - 3/16
04225 - 3/16
04211 - 7/32
04216 - 7/32
04220 - 7/32
04211 - 1/4
04216 - 1/4
04216 - 9/32
14
ER 20
ER 25
ER 32
ER 40
Range
Shank
.043 - .062"
1/16"
.054 - .093"
3/32"
04240 - 1/8
.086 - .125"
1/8"
04232 - 5/32
04240 - 5/32
.117 - .156"
5/32"
04232 - 3/16
04240 - 3/16
.148 - .187"
3/16"
04225 - 7/32
04232 -7/32
04240 - 7/32
.179 - .218"
7/32"
04220 - 1/4
04225 - 1/4
04232 - 1/4
04240 - 1/4
.211 - .250"
1/4"
04220 - 9/32
04225 - 9/32
04232 - 9/32
04240 - 9/32
.242 - .281"
9/32"
04216 - 5/16
04220 - 5/16
04225 - 5/16
04232 - 5/16
04240 - 5/16
.273 - .312"
5/16"
04216 - 11/32
04220 - 11/32
04225 - 11/32
04232 - 11/32
04240 - 11/32
.304 - .343"
11/32"
04216 - 3/8
04220 - 3/8
04225 - 3/8
04232 - 3/8
04240 - 3/8
.336 - .375"
3/8"
04216 - 13/32
04220 - 13/32
04225 - 13/32
04232 - 13/32
04240 - 13/32
.367 - .406"
13/32"
04220 - 7/16
04225 - 7/16
04232 - 7/16
04240 - 7/16
.398 - .437"
7/16"
04220 - 15/32
04225 - 15/32
04232 - 15/32
04240 - 15/32
.429 - .468"
15/32"
04220 - 1/2
04225 - 1/2
04232 - 1/2
04240 - 1/2
.461 - .500"
1/2"
04225 - 17/32
04232 - 17/32
04240 - 17/32
.492 - .531"
17/32"
04225 - 9/16
04232 - 9/16
04240 - 9/16
.523 - .562"
9/16"
04225 - 19/32
04232 - 19/32
04240 - 19/32
.554 - .593"
19/32"
04225 - 5/8
04232 - 5/8
04240 - 5/8
.586 - .625"
5/8"
04232 - 21/32
04240 - 21/32
.617 - .656"
21/32"
04232 - 11/16
04240 - 11/16
.648 - .687"
11/16"
04232 - 23/32
04240 - 23/32
.679 - .718"
23/32"
04232 - 3/4
04240 - 3/4
.711 - .750"
3/4"
04240 - 7/8
.836 - .875"
7/8"
04240 - 1
.961 - 1.00"
1"
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.
ER Precision Metric Collets
ER 8, ER 11, Precision Metric Collets
• Runout (T.I.R.) .0002"
• Collapse range: 0.039"
• Collet sets available
Our ER collets are made from high-carbon bearing
steel that is heat-treated for improved flexibility and
longer life. Each collet is precisely ground and honed
using a swiss technique, then individually inspected
and tested for quality. Compatible with DR, RD, ESX,
AR, & BR series collets.
ER 8
ER 11
Inch
Range
Metric
04208 - 01.0
04211 - 01.0
1/32"
.019 - .039"
0.5 - 1.0
04208 - 01.5
04211 - 01.5
3/64"
.039 - .059"
1.0 - 1.5
04208 - 02.0
04211 - 02.0
1/16"
.059 - .079"
1.5 - 2.0
04208 - 02.5
04211 - 02.5
3/32"
.079 - .098"
2.0 - 2.5
04208 - 03.0
04211 - 03.0
7/64"
.098 - .118"
2.5 - 3.0
04208 - 03.5
04211 - 03.5
1/8"
.118 - .138"
3.0 - 3.5
04208 - 04.0
04211 - 04.0
5/32"
.138 - .157"
3.5 - 4.0
04208 - 04.5
04211 - 04.5
11/64"
.157 - .177"
4.0 - 4.5
04208 - 05.0
04211 - 05.0
3/16"
.177 - .197"
4.5 - 5.0
04211 - 05.5
13/64"
.197 - .217"
5.0 - 5.5
04211 - 06.0
7/32"
.217 - .236"
5.5 - 6.0
04211 - 06.5
1/4"
.236 - .256"
6.0 - 6.5
04211 - 07.0
17/64"
.256 - .276"
6.5 - 7.0
Inch
Range
Metric
1/32"
.019 - .039"
0.5-1
1/16"
.039 - .079"
1-2
7/64"
.079 - .118"
2-3
ER 16, 20, 25, 32, 40, Precision Metric Collets
ER 16
ER 20
ER 25
ER 32
ER 40
04216 - 02
04220 - 02
04225 - 02
04216 - 03
04220 - 03
04225 - 03
04232 - 03
04216 - 04
04220 - 04
04225 - 04
04232 - 04
04240 - 04
1/8"
.118 - .157"
3-4
04216 - 05
04220 - 05
04225 - 05
04232 - 05
04240 - 05
3/16"
.157 - .197"
4-5
04216 - 06
04220 - 06
04225 - 06
04232 - 06
04240 - 06
7/32"
.197 - .236"
5-6
04216 - 07
04220 - 07
04225 - 07
04232 - 07
04240 - 07
1/4"
.236 - .276"
6-7
04216 - 08
04220 - 08
04225 - 08
04232 - 08
04240 - 08
5/16"
.276 - .315"
7-8
04216 - 09
04220 - 09
04225 - 09
04232 - 09
04240 - 09
11/32"
.315 - .354"
8-9
04216 - 10
04220 - 10
04225 - 10
04232 - 10
04240 - 10
3/8"
.354 - .394"
9-10
04220 - 11
04225 - 11
04232 - 11
04240 - 11
13/32"
.394 - .433"
10-11
04220 - 12
04225 - 12
04232 - 12
04240 - 12
7/16"
.433 - .472"
11-12
04220 - 13
04225 - 13
04232 - 13
04240 - 13
1/2"
.472 - .512"
12-13
04225 - 14
04232 - 14
04240 - 14
17/32"
.512 - .551"
13-14
04225 - 15
04232 - 15
04240 - 15
9/16"
.551 - .591"
14-15
04225 - 16
04232 - 16
04240 - 16
5/8"
.591 - .630"
15-16
04232 - 17
04240 - 17
21/32"
.630 - .669"
16-17
04232 - 18
04240 - 18
11/16"
.669 - .709"
17-18
04232 - 19
04240 - 19
3/4"
.709 - .748"
18-19
04232 - 20
04240 - 20
25/32"
.748 - .787"
19-20
04240 - 21
13/16"
.787 - .827"
20-21
04240 - 22
27/32"
.827 - .866"
21-22
04240 - 23
7/8"
.866 - .906"
22-23
04240 - 24
15/16"
.906 - .945"
23-24
04240 - 25
31/32"
.945 - .984"
24-25
04240 - 26
1"
.984 - 1.024"
25-26
04216 - 01
Note: 0.5mm increment collets are available on request.
All Techniks products are backed by our 100% satisfaction guarantee!
15
Why CNC Routers Run Better with Power Coat Nuts
Power Coat Nuts = 40% More Holding Power Than Bearing Nuts
• Less runout (T.I.R.)
• Greater rigidity (accuracy)
• Better balance (no moving parts)
collet shoulder
Power Coat nuts are manufactured with a special process
threads
that reduces friction between
the nut, collet shoulder, and
tool holder threads. This greatly increases holding power so
runout (T.I.R.) is improved. Bet-
Power Coat nuts perform the job of keeping your toolholder
assembly intact and cutting true under extreme load conditions.
ter T.I.R. means cutting is faster
See a video demonstrating how Power Coat nuts hold
and smoother and tool life is
tighter to improve CNC router performance and shop
improved too.
safety at: www.techniksusa.com/pcnut
Bearing Nuts = Old Technology
Bearing nuts cannot be
balanced because they
Rubber bearing seals fail,
then dust contaminates
bearings, making them seize.
have moving parts, so
cutting tools wear
prematurely.
Uncoated threads limit
holding power.
16
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.
Ultra High Speed Power Coat ER Collet Nuts
• 40% more holding power than bearing nuts
• Safer: cutting tool is less likely break free
• Balanced up to 70,000 RPM
Power Coat nuts increase holding power because they reduce
friction between the nut and the
collet shoulder, and the tool holder
threads and the nut. This creates
more downforce on the collet,
making it collapse tighter around
the tool shank.
TEST RESULTS - Nut Comparison
All nuts torqued to 70 ft/lbs
Power Coat breaks free at 140 ft/lbs
40% more holding power than
bearing nuts provide!
Because holding power is 40%
better than bearing nuts accuracy,
cutter performance, saftey, and
tool life are all improved!
Bearing Nut breaks free
at 100 ft/lbs
25% more holding power
Standard nut breaks free at 80 ft/lbs
80
90
100
110
120
130
140
Holding Power - Foot/Pounds Torque
Ultra High-Speed ER Coated Nuts
Dimensions are in millimeters.
Part No.
Description
D
B
M
Max. Speed
Wrench
* Max. Torque
46111
ER RH 11 B Nut
19
11.8
M14 x 0.75
70,000
04608
20 ft/lbs
46116
ER RH 16 B Nut
32
18.0
M22 x 1.5
65,000
04613
50 ft/lbs
46120
ER RH 20 B Nut
35
19.5
M25 x 1.5
60,000
04614
75 ft/lbs
46125
ER RH 25 B Nut
42
20.5
M32 x 1.5
55,000
04615
95 ft/lbs
46132
ER RH 32 B Nut
50
23.0
M40 x 1.5
50,000
04616
125 ft/lbs
46140
ER RH 40 B Nut
63
26.0
M50 x 1.5
40,000
04617
140 ft/lbs
*Recommended torque is 80-90% of maximum value. See page 29 for torque wrench.
All Techniks products are backed by our 100% satisfaction guarantee!
17
ER Bearing Nuts and High Speed Mini Nuts
• Bearings reduce friction between collet and nut
• 25% more holding power than standard nuts
• Helps prolong tool life
Bearing nuts reduce friction between
the nut and the collet shoulder.
This creates more downforce on the
collet, making it collapse tighter
around the tool shank.
For maximum holding power use
Power Coat nuts.
Dimensions are in millimeters.
ER Bearing Nuts
Part No.
Description
D
B
M
Wrench
* Max. Torque
29132
ER 32 HS Bearing Nut
50
25
M40x1.5
04616
125 ft/lbs
21240
ER 40 HS Bearing Nut
63
28
M50x1.5
04617
140 ft/lbs
Use these nuts for spindle speeds below 18,000 RPM’s
* Recommended torque is 80-90% of maximum value
• Balanced 20,000 RPM at G 2.5
• Narrow nose diameter
• Left hand nut available
Use ER High Speed mini nuts for
applications where speed exceeds
10,000 RPM’s. They are balanced
to G2.5 for 20,000 RPM’s. For collet holders and multi-spindle heads
where center or shoulder distances
are important.
These nuts use a special wrench to torque
down the nut. Do not over tighten these nuts.
ER High Speed Mini Nuts
Dimensions are in millimeters.
Part No.
Description
D
B
M
Wrench
Max. Torque
33108
ER 8 HS Mini Nut
12
11
M10 x 0.75
04620
7 ft/lbs
33111
ER 11 HS Mini Nut
16
12
M13 x 0.75
04621
14 ft/lbs
33116
ER 16 HS Mini Nut
22
18
M19 x 1.0
04622
22 ft/lbs
33120
ER 20 HS Mini Nut
28
19.5
M24 x 1.0
04623
25 ft/lbs
33125
ER 25 HS Mini Nut
35
21
M30 x 1.0
04624
29 ft/lbs
33125-L
ER25 HS L-Hand Nut
35
21
M30 x 1.0
04624
29 ft/lbs
Recommended torque is 80-90% of maximum value. See page 26 for dust seals.
18
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.
Power Coat ER Dust Seal Nuts – Bearing ER Dust Seal Nuts
• 40% more holding power than bearing nuts!
• Prevent contamination of collets
• Prolongs tool life
Use these nuts with a dust seal
that snaps into the nut to seal
and protect your tools. (pg. 26)
They are available for a wide
range of diameters. Each dust
seal has a .020" range.
Power Coat ER Internal Dust Seal Nuts
Dimensions are in millimeters.
Part No.
Description
D
B
Wrench
T
* Max. Torque
41616
ER 16 HS Internal Dust Seal Coated Nut
32
22.5
04613
M22x1.5
50 ft/lbs
41620
ER 20 HS Internal Dust Seal Coated Nut
35
24
04614
M25x1.5
75 ft/lbs
41625
ER 25 HS Internal Dust Seal Coated Nut
42
25
04615
M32x1.5
95 ft/lbs
41632
ER 32 HS Internal Dust Seal Coated Nut
50
27.5
04616
M40x1.5
125 ft/lbs
41640
ER 40 HS Internal Dust Seal Coated Nut
63
30.7
04617
M50x1.5
140 ft/lbs
See page 26 for dust seals.
• Prevent contamination of collets
• Prolongs tool life
• Helps keep tool holder clean
Use these nuts with a dust seal
that snaps into the nut to seal and
protect your tools. The dust seals
can be found on page 26. They
are available for a wide range of
diameters. Each dust seal has a
.020" range.
Bearing ER Internal Dust Seal Nuts
Dimensions are in millimeters.
Part No.
Description
D
B
M
Wrench
* Max. Torque
21325
ER 25 Internal Dust Seal Bearing Nut
42
22.5
M32x1.5
04615
95 ft/lbs
21332
ER 32 Internal Dust Seal Bearing Nut
50
25
M40x1.5
04616
125 ft/lbs
21340
ER 40 Internal Dust Seal Bearing Nut
63
28
M50x1.5
04617
140 ft/lbs
Recommended torque is 80-90% of maximum value. See page 26 for dust seals.
All Techniks products are backed by our 100% satisfaction guarantee!
19
TG 75 and TG 100 Precision Collets
• Runout (T.I.R.) .0004"
• Collapse range: 1/64"
• Collet sets available
TG 75 Collet
TG 100 Collet
Our TG collets are made from highcarbon bearing steel that is heattreated for improved flexibility and
longer life.
Each collet is precisely ground and
honed using a swiss technique,
then individually inspected and
tested for quality.
Snap collet into the nut before
screwing nut onto spindle or
collet holder.
TG 75 Collets
Part No.
ID Size
Part No.
ID Size
3/32"
04008 - 7/16
7/16"
04008 - 1/8
1/8"
04008 - 15/32
15/32"
04008 - 5/32
5/32"
04008 - 1/2
04008 - 3/16
3/16"
04008 - 17/32
17/32"
04008 - 7/32
7/32"
04008 - 9/16
9/16"
04008 - 1/4
1/4"
04008 - 19/32
19/32"
04008 - 9/32
9/32"
04008 - 5/8
04008 - 5/16
5/16"
04008 - 21/32
21/32"
04008 - 11/32
11/32"
04008 - 11/16
11/16"
Series
L
A
3/8"
04008 - 23/32
23/32"
TG 75
1.844"
1.062"
3/4"
TG 100
2.375"
1.379"
04008 - 3/32
04008 - 3/8
04008 - 13/32
13/32"
04008 - 3/4
1/2"
5/8"
Dimensions
TG 100 Collets
Part No.
ID Size
Part No.
ID Size
Part No.
ID Size
23/32"
04010 - 3/32
3/32"
04010 - 13/32
13/32"
04010 - 23/32
04010 - 1/8
1/8"
04010 - 7/16
7/16"
04010 - 3/4
04010 - 5/32
5/32"
04010 - 15/32
15/32"
04010 - 25/32
25/32"
04010 - 3/16
3/16"
04010 - 1/2
1/2"
04010 - 13/16
13/16"
04010 - 7/32
7/32"
04010 - 17/32
17/32"
04010 - 27/32
27/32"
04010 - 1/4
1/4"
04010 - 9/16
9/16"
04010 - 7/8
04010 - 9/32
9/32"
04010 - 19/32
19/32"
04010 - 29/32
29/32"
04010 - 5/16
5/16"
04010 - 5/8
5/8"
04010 - 15/16
15/16"
04010 - 11/32
11/32"
04010 - 21/32
21/32"
04010 - 31/32
31/32"
3/8"
04010 - 11/16
11/16"
04010 - 1
04010 - 3/8
20
3/4"
7/8"
1"
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.
Power Coat TG Collet Nuts and TG Dust Seal Collet Nuts
• Power Coat for 40% more holding power
• No bearings to seize and fail
• Balanced up to 20,000 RPM
Power Coat nuts increase holding power because they reduce
friction between the nut and the
collet shoulder, and the tool holder
threads and the nut. This creates
more downforce on the collet,
making it collapse tighter around
the tool shank.
Regular Style
Use TG 100 dust cover style nuts
(bottom) to prevent contamination
of collet with dust and particles.
TG Collet Nuts
Part No.
Description
D
d1
T
I1
L
Spanner
Torque*
27500
TG75 Collet Nut
1.88"
-
1 1/2 - 12"
0.32"
0.94"
04018
100 ft/lb
28110
TG100 Collet Nut
2.35"
1.12"
1 7/8 - 12"
0.44"
1.18"
03691
100 ft/lb
* Recommended torque is 80-90% of maximum value. See page 29 for torque wrench.
• Prevent contamination of collets
• Helps keep tool holder clean
• Power Coat provides 40% better
holding power
Dust Cover Style
Use these nuts with a dust seal that snaps
into the nut to seal and protect your tools.
The dust covers can be found on page 26.
Power Coat nuts increase holding power because they
reduce friction between the nut and the collet shoulder, and the tool holder threads and the nut. This creates more downforce on the collet, making it collapse
tighter around the tool shank.
TG Dust Seal Collet Nuts
Part No.
Description
28210
TG100 Dust Seal Nut
D
d1
T
I1
L
Spanner
Torque*
2.35"
0.95"
1 7/8 - 12"
0.44"
1.41"
03691
100 ft/lb
* Recommended torque is 80-90% of maximum value. See page 29 for torque wrench.
All Techniks products are backed by our 100% satisfaction guarantee!
21
Shoda Collets and Nuts
Old Style
Piggyback Style
New Style
Super Shoda
Our Shoda collets are the most accurate in the industry. We use heat-treated high
carbon bearing steel and a Swiss grinding technique that ensures accuracy.
• Precision ground accuracy
Shoda Collets
• Heat-treated carbon steel
Dimensions are in millimeters unless otherwise indicated.
Part Number
Description
A
d
L
SD-20mm-.250
Shoda 20mm (old style) 1/4" collet
20
.250"
52
SD-20mm-.312
Shoda 20mm (old style) 5/16" collet
20
.312"
52
SD-20mm-.375
Shoda 20mm (old style) 3/8" collet
20
.375"
52
SD-20mm-.500
Shoda 20mm (old style) 1/2" collet
20
.500"
52
SD-20mm-.625
Shoda 20mm (old style) 5/8" collet
20
.625"
52
SD-C001-.125
Shoda Piggyback 1/8" collet
16
.125"
52
SD-C001-.187
Shoda Piggyback 3/16" collet
16
.187"
52
SD-C001-.250
Shoda Piggyback 1/4" collet
16
.250"
52
SD-C001-.312
Shoda Piggyback 5/16" collet
16
.312"
52
SD-C001-.375
Shoda Piggyback 3/8" collet
16
.375"
52
SD-C001-.500
Shoda Piggyback 1/2" collet
16
.500"
52
SD-C015-.125
Shoda 24mm (new style) 1/8" collet
24
.125"
52
SD-C015-.250
Shoda 24mm (new style) 1/4" collet
24
.250"
52
SD-C015-.312
Shoda 24mm (new style) 5/16" collet
24
.312"
52
SD-C015-.375
Shoda 24mm (new style) 3/8" collet
24
.375"
52
SD-C015-.500
Shoda 24mm (new style) 1/2" collet
24
.500"
52
SD-C015-.625
Shoda 24mm (new style) 5/8" collet
24
.625"
52
SD-C015-.750
Shoda 24mm (new style) 3/4" collet
24
.750"
52
SS-22-1/4
Super Shoda 1/4" collet
23
1/4"
40
SS-22-3/8
Super Shoda 3/8" collet
23
3/8"
40
SS-22-10
Super Shoda 10mm collet
23
10
40
SS-22-1/2
Super Shoda 1/2" collet
23
1/2"
40
Note: Other sizes available on request.
Shoda SD collet
Super Shoda SS collet
Super Shoda nut
New style nut
Shoda Collet Nuts
Dimensions are in millimeters.
Part Number
Description
A
d
L
SD-C001-Nut
Shoda piggy back collet nut
36
14
30
SD-20mm-Nut
Shoda old style collet nut
41
19
30
SD-C015-Nut
Shoda new style collet nut
46
22
30
SS-22-Nut
Super Shoda collet nut
36
12.5
15
SS-22-Ext -Nut
Super Shoda extended nut
36
12.5
30
22
• Individually inspected
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.
Perske DIN 6388 Collets and Nuts
• Runout (T.I.R.) .0004"
• Collapse range: 1/64"
• Made to DIN 6388 standards
These Perske collets are made
from high-carbon bearing steel
that is heat-treated for improved
flexibility and longer life.
Each collet is precisely ground and
honed using a swiss technique,
then individually inspected and
tested for quality.
Perske Collets
EOC 08
SYOZ 20/EOC 12
EOC 16
SYOZ 25
Shank
03508-1/8
03520-1/8
03531-1/8
03868-1/8
1/8"
03508-3/16
03520-3/16
03531-3/16
03868-3/16
3/16"
03508-1/4
03520-1/4
03531-1/4
03868-1/4
1/4"
03508-5/16
03520-5/16
03531-5/16
03868-5/16
5/16"
03520-3/8
03531-3/8
03868-3/8
3/8"
03520-7/16
03531-7/16
03868-7/16
7/16"
03520-1/2
03531-1/2
03868-1/2
1/2"
03531-9/16
03868-9/16
9/16"
03531-5/8
03868-5/8
5/8"
03868-3/4
3/4"
03868-7/8
7/8"
Dimensions
03868-1
1"
Part No.
L
D
03531-10
03868-10
10mm
EOC 08
26mm
14.4mm
03531-16
03868-16
16mm
EOC 16
40mm
25.5mm
03868-20
20mm
SYOZ 20
34mm
20mm
03868-25
25mm
SYOZ 25
52mm
35mm
03520-10
Perske Nuts and Wrenches
Part No.
Snap collet into the nut before
screwing nut onto spindle or collet
holder.
Dimensions are in millimeters.
Type
L
D
Wrench
03508
EOC 08
19
30
-
03636
EOC 16
24
43
-
03520
SYOZ 20/EOC 12
20
35
22220
03638
SYOZ 25
30
60
03691
All Techniks products are backed by our 100% satisfaction guarantee!
23
DNA – Dead Nuts Accurate – ER 16 Collets and Nuts
DNA Collets Feature
• 0.0002" T.I.R.
• Best collet for tools 6mm and smaller
• Works with standard ER 16 holders
Twice as much
metal holding
tool shank!
Designed to hold tighter with greater
rigidity for improved T.I.R. and tool life.
For improved concentricity and consistent T.I.R. 6mm and
under, use DNA collets in place of ER 16 collets.
DNA Ultra-Precision Metric Collets
Part No
Description - Shank
1016.0030
Inch Shank
Collapse
DNA 16 0.3 - 0.2 mm
.0118 – .0079"
0.10 mm
1016.0040
DNA 16 0.4 - 0.3 mm
.0157 – .0118"
0.10 mm
1016.0050
DNA 16 0.5 - 0.4 mm
.0197 – .0157"
0.10 mm
1016.0060
DNA 16 0.6 - 0.5 mm
.0236 – .0196"
0.10 mm
1016.0080
DNA 16 0.8 - 0.7 mm
.0315 – .0276"
0.10 mm
1016.0100
DNA 16 1.0 - 0.9 mm
.0394 – .0354"
0.10 mm
1016.0120
DNA 16 1.2 - 1.1 mm
.0472 – .0433"
0.10 mm
1116.0125
DNA 16 1.25 - 1.00 mm
.0492 – .0394"
0.25 mm
1116.0150
DNA 16 1.50 - 1.25 mm
.0590 – .0492"
0.25 mm
1116.0175
DNA 16 1.75 - 1.50 mm
.0688 – .0590"
0.25 mm
1116.0200
DNA 16 2.00 - 1.75 mm
.0787 – .0688"
0.25 mm
1116.0225
DNA 16 2.25 - 2.00 mm
.0885 – .0787"
0.25 mm
1116.0250
DNA 16 2.50 - 2.25 mm
.0984 – .0885"
0.25 mm
1116.0300
DNA 16 3.00 - 2.50 mm
.1181 – .0984"
0.50 mm
1116.0350
DNA 16 3.50 - 3.00 mm
.1337 – .1181"
0.50 mm
1116.0400
DNA 16 4.00 - 3.50 mm
.1574 – .1337"
0.50 mm
1116.0450
DNA 16 4.50 - 4.0 mm
.1771 – .1574"
0.50 mm
1116.0500
DNA 16 5.00 - 4.00 mm
.1968 – .1574"
1.0 mm
1116.0600
DNA 16 6.00 - 5.00 mm
.2362 – .1968"
1.0 mm
1116.0700
DNA 16 7.00 - 6.00 mm
.2755 – .2362"
1.0 mm
1116.0800
DNA 16 8.00 - 7.00 mm
.3149 – .2755"
1.0 mm
1116.0900
DNA 16 9.00 - 8.00 mm
.3543 – .3149"
1.0 mm
1116.1000
DNA 16 10.0 - 9.00 mm
.3927 – .3543"
1.0 mm
DNA Ultra-Precision Inch Collets
Part No
Description - Shank
1116.0018
Inch Shank
Collapse
DNA 16 1/8"
.1250 – .1050"
0.50 mm
1116.0316
DNA 16 3/16"
.1875 – .1675"
0.50 mm
1116.0014
DNA 16 1/4"
.250 – .230"
0.50 mm
1116.0038
DNA 16 3/8"
.375 – .355"
0.50 mm
24
ER Collet
DNA Collet
DNA Nut
DNA Sealed Nut
DNA wrench & torque wrench adapter
DNA Collet Nuts, Sealed Nuts, Wrenches
Part No
Description
2016-200
DNA16 M19 x1 Mini Nut
27116
M22 x 1.5 nut
27216
M22 x 1.5 nut 1/8" o-ring
27116-30
3.0 - 2.5mm sealed nut
27116-40
4.0 - 3.5mm sealed nut
27116-45
4.5 - 4.0mm sealed nut
27116-50
5.0 - 4.5mm sealed nut
27116-55
5.5 - 5.0mm sealed nut
27116-60
6.0 - 5.5mm sealed nut
27116-65
6.5 - 6.0mm sealed nut
DNA16W
DNA 16 Collet Wrench
DNA16-TWA
DNA 16 Torque Wrench Adapter
894-22
DNA 16 Mini Nut Wrench
Sealed nuts prevent contamination. Nut O.D. = 27mm
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.
Retention Knobs for CNC Routers and Special Orders
For safe operation please make sure that the
pull stud you order is the exact pull stud your
machine uses. Improper choice of pull stud can
cause damage to the spindle and/or toolholder,
and is a potential safety hazard.
D
d3
d2
d1
T
Retention knobs make the important connection between the spindle and
the tool holder. Always use the correct retention knob for your tool holder
and machine spindle and tighten it properly. Refer to the diagram (right).
l1
Retention Knobs
l2
L
Dimensions are in millimeters.
Part No.
Type
D
d1
d2
d3
L
I1
I2
θ
T
750-19
KOMO ISO/BT30-A 12.5
17
13
9
12.5
44
23.4
18.2
15°
M12
13001
DAT 30- A
17
13
9
13
44
24
19
15°
M12
13003
DAT 40 – A
23
19
14
17
54
26
20
15°
M16
13001-45
Colombo ISO 30 - Ball
17
12.8
9
13
44
24
19
45°
M12
49019
HSD ISO 30
17
12
8
13
44
23.9
-
radius
M12
07801
BT 30 - 45°
16.5
11
7
12.5
43
23
-
45°
M12
07806
BT 30 - 60°
16.5
11
7
12.5
43
23
-
60°
M12
07812
BT30 - 90°
16.5
11
7
12.5
43
23
8
M12
4403502
BT 35- Heian
20
13
8.5
12.5
43
28
22.5
-
M12
13003
DAT 40 – A
23
19
14
17
54
26
20
15°
M16
07803
BT40 - 45°
23
15
10
17
60
35
28
-
M16
07808
BT40 - 60°
23
15
10
17
60
35
28
-
M16
07814
BT40 - 90°
23
15
10
17
60
35
28
-
M16
13001 – Colombo Spindles (Billet spindle) 13001-45 – Colombo spindle clamping by balls (RS spindle)
750-19 – KOMO router for BT 30 tool holder, 13019 – HSD spindles
D
Special Pull Studs
We can get the pull studs you need. Just fill in your pull
stud(s) dimensions on the chart below before you call.
Keep your information in this catalog for easy re-orders.
For safe operation please make sure that the pull stud you
order is the exact pull stud your machine uses. Improper
choice of pull stud can cause damage to the spindle and/
or toolholder, and is a potential safety hazard.
Stud
Machine
d1
d2
d3
d2
d1
T
l1
I1
l2
I2
All Techniks products are backed by our 100% satisfaction guarantee!
θ
T
25
Internal Dust Seals for ER 16 to ER 40 Collets
• Eliminates cleaning collets!
Seal fits inside nut before
assembling with collet.
• Extends the life of your collets
• Use with Dust Cover Nuts (pgs. 19, 21)
Internal Dust Seals
ER 16
08516 - 03.5
08516 - 04.0
08516 - 04.5
08516 - 05.0
08516 - 05.5
08516 - 06.0
08516 - 06.5
08516 - 07.0
08516 - 07.5
08516 - 08.0
08516 - 08.5
08516 - 09.0
08516 - 09.5
08516 - 10.0
26
Ranges are in millimeters.
ER 20
08520 - 03.5
08520 - 04.0
08520 - 04.5
08520 - 05.0
08520 - 05.5
08520 - 06.0
08520 - 06.5
08520 - 07.0
08520 - 07.5
08520 - 08.0
08520 - 08.5
08520 - 09.0
08520 - 09.5
08520 - 10.0
08520 - 10.5
08520 - 11.0
08520 - 11.5
08520 - 12.0
08520 - 12.5
08520 - 13.0
ER 25
08525 - 03.5
08525 - 04.0
08525 - 04.5
08525 - 05.0
08525 - 05.5
08525 - 06.0
08525 - 06.5
08525 - 07.0
08525 - 07.5
08525 - 08.0
08525 - 08.5
08525 - 09.0
08525 - 09.5
08525 - 10.0
08525 - 10.5
08525 - 11.0
08525 - 11.5
08525 - 12.0
08525 - 12.5
08525 - 13.0
08525 - 13.5
08525 - 14.0
08525 - 14.5
08525 - 15.0
08525 - 15.5
08525 - 16.0
ER 32
08532 - 03.5
08532 - 04.0
08532 - 04.5
08532 - 05.0
08532 - 05.5
08532 - 06.0
08532 - 06.5
08532 - 07.0
08532 - 07.5
08532 - 08.0
08532 - 08.5
08532 - 09.0
08532 - 09.5
08532 - 10.0
08532 - 10.5
08532 - 11.0
08532 - 11.5
08532 - 12.0
08532 - 12.5
08532 - 13.0
08532 - 13.5
08532 - 14.0
08532 - 14.5
08532 - 15.0
08532 - 15.5
08532 - 16.0
08532 - 16.5
08532 - 17.0
08532 - 17.5
08532 - 18.0
08532 - 18.5
08532 - 19.0
08532 - 19.5
08532 - 20.0
ER 40
08540- 03.5
08540 - 04.0
08540 - 04.5
08540 - 05.0
08540 - 05.5
08540 - 06.0
08540 - 06.5
08540 - 07.0
08540 - 07.5
08540 - 08.0
08540 - 08.5
08540 - 09.0
08540 - 09.5
08540 - 10.0
08540 - 10.5
08540 - 11.0
08540 - 11.5
08540 - 12.0
08540 - 12.5
08540 - 13.0
08540 - 13.5
08540 - 14.0
08540 - 14.5
08540 - 15.0
08540 - 15.5
08540 - 16.0
08540 - 16.5
08540 - 17.0
08540 - 17.5
08540 - 18.0
08540 - 18.5
08540 - 19.0
08540 - 19.5
08540 - 20.0
08540 - 20.5
08540 - 21.0
08540 - 21.5
08540 - 22.0
08540 - 22.5
08540 - 23.0
08540 - 23.5
08540 - 24.0
08540 - 24.5
08540 - 25.0
08540 - 25.5
Metric Shank
3.5 - 3.0
4.0 - 3.5
4.5 - 4.0
5.0 - 4.5
5.5 - 5.0
6.0 - 5.5
6.5 - 6.0
7.0 - 6.5
7.5 - 7.0
8.0 - 7.5
8.5 - 8.0
9.0 - 8.5
9.5 - 9.0
10.0 - 9.5
10.5 - 10.0
11.0 - 10.5
11.5 - 11.0
12.0 - 11.5
12.5 - 12.0
13.0 - 12.5
13.5 - 13.0
14.0 - 13.5
14.5 - 14.0
15.0 - 14.5
15.5 - 15.0
16.0 - 15.5
16.5 - 16.0
17.0 - 16.5
17.5 - 17.0
18.0 - 17.5
18.5 - 18.0
19.0 - 18.5
19.5 - 19.0
20.0 - 19.5
20.5 - 20.0
21.0 - 20.5
21.5 - 21.0
22.0 - 21.5
22.5 - 22.0
23.0 - 22.5
23.5 - 23.0
24.0 - 23.5
24.5 - 24.0
25.0 - 24.5
25.5 - 25.0
Inch Shank
1/8"
5/32"
11/64"
3/16"
13/64"
7/32"
1/4"
17/64"
9/32"
5/16"
21/64"
11/32"
3/8"
25/64"
13/32"
27/64"
7/16"
15/32"
31/64"
1/2"
17/32"
35/64"
9/16"
37/64"
19/32"
5/8"
41/64"
21/32"
11/16"
45/64"
23/32"
3/4"
49/64"
25/32"
51/64"
13/16"
27/32"
55/64"
7/8"
29/32"
59/64"
15/16"
61/64"
31/32"
1"
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.
External Dust Covers For Tool Shanks – Spindle Wipers
• Eliminates cleaning collets!
• Extends the life of your collets
• Extends tool life by maintaining T.I.R.
For 3/16" thru 3/4" tool shanks.
Works with: TG 75, TG 100, ER 25, ER 32, ER 40,
SYOZ 25, SD-CO15, SD-20MM
Installed Dust Seal
Simple and effective dust covers prevent costly failures and reduce downtime
by keeping unwanted particles from entering the collet pocket.
Keeping your tool holder clean insures proper balance, maximizes grip on tool
shank, and reduces downtime spent cleaning out collets during tool changes.
External Dust Covers
Installation
Part No.
Description
DC32-3/16
Dust cover for 3/16" tool shank
1. Place dust cover on tool shank
DC32-1/4
Dust cover for 1/4" tool shank
2. Insert tool into collet/nut assembly
DC32-5/16
Dust cover for 5/16" tool shank
DC32-3/8
Dust cover for 3/8" tool shank
DC32-1/2
Dust cover for 1/2" tool shank
DC32-5/8
Dust cover for 5/8" tool shank
DC32-3/4
Dust cover for 3/4" tool shank
3. Tighten assembly into toolholder using
proper torque
Note: Do not slide dust cover over cutting edge of tool or you
may damage the dust cover.
• For CAT, BT, HSK spindles
• Remove contaminants to improve T.I.R.
• Keeps spindles and tool holders clean
Spindle Wipers
Part No.
Dimensions are in millimeters.
Taper
Total
Taper
17706
30
170
60
17707
40
188
78
17708
50
240
120
07710
HSK 63A
165
31
07711
HSK 63F
165
31
Real lambskin provides the best cleaning. Use with
any type of machine with a taper of 7/24 CAT, BT
or DIN 69871.
All Techniks products are backed by our 100% satisfaction guarantee!
27
Hand Wrenches
DIN 894 Hex Wrench
ER 20A Hex Wrench
ER 20E Slotted Wrench
ER 20 Mini Wrench
TG Hook Wrench
Note: Proper torque on the collet nut reduces collet
wear, keeps tools securely in tool holder and saves you
time and money. See the Recommended Torque Chart
on the back cover for proper torque values.
Torque down the nut to 80-90% of maximum torque
value. Do not over tighten nuts as this will prematurely
cause collets for fail and damage tool holder.
Use a tightening fixture to secure the tool holder. (pg. 30)
Type A, UM, RU, and M Wrenches
Part No.
Description
04608
Dimensions are in millimeters.
Nut Type
Length
Width
ER 11-A Wrench
A (Hex)
120
40
04609
ER 16-A Wrench
A (Hex)
140
53
04610
ER 20-A Wrench
A (Hex)
160
60
04613
ER 16-E Wrench
Slotted
160
55
04614
ER 20-E Wrench
Slotted
180
60
04615
ER 25-E Wrench
Slotted
206
65
04616
ER 32-E Wrench
Slotted
253
75
04617
ER 40-E Wrench
Slotted
289
90
04618
ER 50-E Wrench
Slotted
351
110
04620
ER 8-M Wrench
ER Mini
75
13
04621
ER 11-M Wrench
ER Mini
95
17
04622
ER 16-M Wrench
ER Mini
117
22.5
04623
ER 20-M Wrench
ER Mini
129
28.5
04624
ER 25-M Wrench
ER Mini
142.5
35.5
04018
TG 75 Wrench
Hook Type
253
46
03691
TG 100 / SYOZ 25 Wrench
Hook Type
260
46
22220
SY0Z 20 Wrench
Hook Type
28
34
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.
Torque Wrenches and Adapters
• Get consistant cutting tool performance
• Ensure proper tightening for best T.I.R.
• Prevent tool accidents
Adjustable Torque Wrench
Part No.
Torque Range
Length
Weight
Spigot
60 TH
5-45 ft/lbs
12"
1 lb.
16mm round
200 TH
30-150 ft/lbs
16.5"
1.75 lbs
16mm round
300 TH
45-228 ft/lbs
21.5"
2.5 lbs
16mm round
Collet Keys For Adjustable Torque Wrench
Part No.
Collet Nut Size
Type
Max. Torque*
04576
ER 11 Mini
MIni
14 ft/lbs
04577
ER 16 Mini
MIni
22 ft/lbs
04578
ER 20 Mini
MIni
25 ft/lbs
04587
ER 25 Mini
MIni
29 ft/lbs
04580-16
ER 16 Slotted
Slotted
50 ft/lbs
04601-16
ER 16 Hex
Hex
50 ft/lbs
04580-20
ER 20 Slotted
Slotted
75 ft/lbs
04602-20
ER 20 Hex
Hex
75 ft/lbs
04603-25
ER 25 Slotted
Slotted
95 ft/lbs
04604-32
ER 32 Slotted
Slotted
125 ft/lbs
04605-40
ER 40 Slotted
Slotted
140 ft/lbs
03690-25
SYOZ 25/TG 100
Hook
100 ft/lbs
04018-TWA
TG 75 Slotted
Hook
100 ft/lbs
DNA16-TWA
DNA 16
Slotted
50 ft/lbs
04588-R
ER 32 Slotted
Slotted
125 ft/lbs
SD-TWA
SYOZ-20
Hook
45 ft/lbs
Set adjustable dial to the correct amount of
torque and tighten nut until wrench “clicks”.
ER 25 Castle
ER Slotted
DNA 16 Slotted
Hex
Retention Knob Sockets–Square Drive
Part No.
Taper or Holder
Flats
Drive
Max. Torque*
PSS - 30BT
BT 30 Taper Retention Knob
0.535"
3/8"
40 ft/lbs
PSS - 30ISO
ISO 30 Taper Retention Knob
0.535"
3/8"
40 ft/lbs
PSS - 40
All 40 Taper Retention Knobs
0.750"
3/8"
85 ft/lbs
PSS - 50
BT 50 Taper Retention Knob
1.187"
1/2"
110 ft/lbs
PSSC - 50
CAT 50 Taper Retention Knob
1.250"
1/2"
110 ft/lbs
TG Hook
04588-R
*Recommended Torque is 80 – 90 % of max. value given.
Fixed Head Square Drives
Part No.
Description
Drive
29828
3/8" Square Drive
3/8"
29827
1/2" Square Drive
1/2"
Retention Knob Sockets
All Techniks products are backed by our 100% satisfaction guarantee!
29
Tightening Fixtures
• For HSK, ISO, BT, CAT spindles
• Change Retention Knobs from underneath
• Bolts right to workbench
Side Mount Tightening Fixture
Part No.
Description
NTS-BT30-38
BT 30 taper - 38mm flats
NTS-BT30-41
BT 30 taper - 41mm flats
NTS-BT30-Slot
BT 30 for tools with drive slots
NTS-ISO20-17
ISO 20 - 17mm flats
NTS-ISO20-22
ISO 20 - 22mm flats
NTS-ISO25-27
ISO 25 - 27mm flats
NTS-ISO30-36
ISO 30 - 36mm flats
NTS-ISO30-38
ISO 30 - 38mm flats
NTS-ISO30-47
ISO 30 - 47mm flats
NTS-HSK63A
HSK63A - no flats
NTS-HSK63F-36
HSK 63F - 36mm flats
NTS-HSK63F-38
HSK 63F - 38mm flats
NTS-HSK63F-41
HSK 63F - 41mm flats
NTS-HSK63F-46
HSK 63F - 46mm flats
NTS-40 Taper
Any CAT 40 or BT 40 taper
A sliding collar engages the wrench
flats on HSK tool holders to allow tightening of collet nut.
A large set-screw
engages the drive slot
in ISO, BT, and CAT tool
holders to securely hold
the tool in the fixture.
• For HSK, ISO, BT, CAT spindles
• Change retention knobs from underneath
• Use with Digital Height Gauge to preset tools
TSHG1 Preset and Tightening Fixtures
Attach tightening fixture to workbench or tool cart
using bolts or screws. Allows easy access to retention knobs from underneath. Tool flats are positively
engaged by locking collar to secure tool holder.
Heavy-duty plate steel construction for maximum
rigidity and durability.
Torque nuts and retention knobs to proper tightness
using a torque wrench for best performance.
30
Part No.
Description
TSHG1-40-CT
CAT 40 taper
TSHG1-30-41
BT 30 taper, 41mm flats
TSHG1-40-BT
BT 40 taper
TSHG1-63F-36
HSK 63F, 36mm flats
TSHG1-63F-38
HSK 63F, 38mm flats
TSHG1-63F-46
HSK 63F, 46mm flats
TSHG1-30-36
ISO 30 taper, 36mm flats
TSHG1-30-38
ISO 30 taper, 38mm flats
TSHG1-30-47
ISO 30 taper, 47mm flats
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.
Digital Height Gauge, Analog Axial Preset Gauge
• 0 – 12" range
• Repeatability 0.0008"
• Automatic inch to metric
conversion
This precision instrument is sealed
against dust, grime, and oil, is
shock and magnetism resistant,
and is covered by a five year
warranty.
Operation
Set the height of your tool
with the digital height gauge,
then torque the nut to the
proper tightness. Refer to the
Torque Chart on back cover.
Use with TSHG1 Tightening Fixture to set tool height. Reduce machine down-time and increase
productivity by presetting tools.
Digital Height Gauge
Part No.
Description
54-212-012
12” Digital Height Gauge
12" inch height measured from gauge line (end of spindle).
• Accuracy 0.0002"
• Easy to measure tool depth
• Height 50mm (2")
Save valuable machine time by using
axial preset gauges to quickly set tool
depth and increase accuracy.
Analog Axial Preset Gauge
Part No.
Description
17906-2
ZSI-50 Preset Gauge
Operation
1. Use the gauge pin included to press down on the spring-loaded center piece as illustrated. Please be sure the gauge pin is placed on the shiny surface.
2. Turn the indicator to read “0”, then remove the gauge pin.
3. Put the unit on the workpiece and carefully jog the tool down to make contact with the
gauge face. When the gauge reads "0" the tool is 50mm (2") above the workpiece.
All Techniks products are backed by our 100% satisfaction guarantee!
31
Unleash the Full Potential of Your CNC Router!
With Techniks Aggregate Heads
Aggregate Head Advantages
• Increase productivity and profitability
• Combine boring, mortising, routing, shaping,
and sawing operations
• Eliminate tool changes, increase your tool
handling capacity
3 inline outputs
for boring
lock recess
See Our Modular Output System Page 40
• Interchangeable outputs increase flexibility.
• Look for “Modular” in the specifications tables
chainsaw
Rotation
Aggregate can be rotated 360˚
Spindle Outputs*
M5, R6, S1, S2, Modular
underside
Floating Aggregate with
Chip Guide System
IWF 2008
Challengers Award Finalist
45˚ fixed angle
moulder
32
Call us toll-free at: (800) 597-3921 to speak to an aggregate head applications specialist.
Our Aggregates Offer Unmatched Quality & Reliability
About our Aggregates
Ultra Line Aggregates are
lubricated in an oil bath and
sealed from contaminants for
extended life and use under
heavy duty conditions. We
recommend the Ultra Line for
sawing using blades larger
than 7", V-grooving, heavy
routing applications, cutting
MDF, composite materials, or
cutting aluminum.
Function Line Aggregates
are grease lubricated for
standard duty operation.
They provide the greatest
number of configurations and
application specific options to
increase router
productivity.
Only the very best components available are used to
create our aggregate heads. This is why our aggregate
heads run cool, quiet, and trouble-free.
Every aggregate head we make is individually hand assembled by one, highly skilled technician, who is personally
responsible for the quality of that aggregate, and signs their
name to the aggregate upon completion.
Our assembly process is a labor of love, but the end
result is well worth the effort.
We promise
Smart Line Aggregates
for light weight routers are
smaller size aggregates for
standard duty operations.
They are grease lubricated
and provide aggregate head
productivity for owners of
smaller CNC routers.
See page 39.
• unmatched reliability
• unmatched performance
• unmatched support
How you benefit
• increase productivity
• increased reliability
• reduced machine down-time
How To Order Aggregates
We offer hundreds of different aggregate configurations, and can make practically any application specific
aggregates you need. We can only show a few of the
most popular models in this catalog. Please specify your
application and center spindle type (ISO, HSK, BT, etc.)
when ordering so we can make sure you get the right
aggregate for your shop.
Call us at (800) 597-3921 to discuss your application
requirements.
All Techniks products are backed by our 100% satisfaction guarantee!
33
Mono Aggregate Heads (1-spindle output)
Mono output aggregates are an affordable way to
add 4th axis capability to your CNC router. Perform routing, boring, mortising, and sawing operations faster to
increase profits. Choose from a wide variety of spindle
optputs. See chart below for supported outputs.
Function Line Mono Dimensions (mm)
HSK center spindle shown.
Please specify your machine spindle and application.
Function Line Mono (grease lubricated)
Spindle Speed Max.
10,000 RPM
Tool Speed Max.
15,000 RPM
Rotation
Aggregate can be rotated 360˚
Gear Ratio
1:1.48
Maximum Torque
15 ft. lbs
Spindle Direction
Same as machine spindle
Maximum Temp.
185˚F
Spindle Outputs*
M5, R6, S1, S2, Modular
Ultra Line Mono Dimensions (mm)
Ultra Line Mono (oil bath lubricated)
Spindle Speed Max.
10,000 RPM
Tool Speed Max.
15,000 RPM
Rotation
Aggregate can be rotated 360˚
Gear Ratio
1:1.48
Gear Reduction*
1:0.676 (*optional feature)
Maximum Torque
17 ft. lbs
Spindle Direction
Same as machine spindle
Maximum Temp.
185˚F
Spindle Outputs*
M5, R6, S1, S2, P1, P2, P3, P4, 05
*See page 40 for spindle output specifications.
34
Aggregate heads are configured to fit your spindle. Please call us at (800) 597-3921 for ordering assistance.
Duo Aggregate Heads (2-spindle outputs)
Use Duo aggregates for faster manufacturing when
more than one tool is required. Choose from a wide
variety of spindle optputs. See chart below for supported
outputs. Possibilities include routing, boring, mortising,
and sawing operations. ER 25 or ER 32.
Function Line Duo Dimensions (mm)
HSK center spindle shown.
Please specify your machine spindle and application.
Function Line Duo (grease lubricated)
Spindle Speed Max.
10,000 RPM
Tool Speed Max.
15,000 RPM
Rotation
Aggregate can be rotated 360˚
Gear Ratio
1:1.48
Maximum Torque
15 ft. lbs
Spindle Direction
#1 clockwise, #2 opposite
Maximum Temp.
185˚F
Spindle Outputs*
M5, R6, S1, S2, Modular
Ultra Line Duo Dimensions (mm)
Ultra Line Duo (oil bath lubricated)
Spindle Speed Max.
10,000 RPM
Tool Speed Max.
15,000 RPM
Rotation
Aggregate can be rotated 360˚
Gear Ratio
1:1.48
Gear Reduction*
1:0.676 (*optional feature)
Maximum Torque
17 ft. lbs
Spindle Direction
#1 clockwise, #2 opposite
Maximum Temp.
185˚F
Spindle Outputs*
M5, R6, S1, S2, P1, P2, P3, P4, 05
*See page 40 for spindle output specifications.
ER Collets sold separately. See pages 14 and 15 to select your ER collets.
35
Quattro Aggregate Heads (4-spindle outputs)
Quattro aggregate heads provide 4 tool spindles for
more flexibility to combine operations. Choose from a
wide variety of spindle optputs. See chart below for supported outputs, and page 40 for output specifications.
Function Line Quattro Dimensions (mm)
HSK center spindle shown.
Please specify your machine spindle and application.
• Add 4th axis capability to your CNC
• Reduce the number of tool changes needed
• Features 2, ER 25 spindles for boring, and
2 ER 32 spindles for custom applications
Function Line Quattro (grease lubricated)
Spindle Speed Max.
10,000 RPM
Tool Speed Max.
15,000 RPM
Rotation
Aggregate can be rotated 360˚
Gear Ratio
1:1.48
Maximum Torque
15 ft. lbs
Maximum Temp.
185˚F
Spindle Outputs*
M5, R6, Modular
*See page 40 for spindle output specifications.
36
Aggregate heads are configured to fit your spindle. Please call us at (800) 597-3921 for ordering assistance.
Vario Aggregate Heads (variable-angle)
The Vario can operate at any angle within it's range
to perform “impossible” cuts, …right on your CNC.
Function Line Vario aggregate operates at any angle
from 0˚ to 100˚. (100˚ adjustable)
Ultra Line Vario aggregate operates at any angle from
-100˚ to 100˚. (200˚ adjustable)
Function Line Vario Dimensions (mm)
HSK center spindle
shown. Please specify
your machine spindle
and application.
Function Line Vario (grease lubricated)
Spindle Speed Max.
15,000 RPM
Tool Speed Max.
15,000 RPM
Rotation
Aggregate can be rotated 360˚
Gear Ratio
1:1
Swiveling Range
0° to 100°
Maximum Torque
15 ft. lbs
Spindle Direction
Opposite machine spindle
Maximum Temp.
185˚F
Spindle Outputs*
K1, K2
Ultra Line Vario Dimensions (mm)
Ultra Line Vario (oil bath lubricated)
Spindle Speed Max.
13,760 RPM
Tool Speed Max.
15,000 RPM
Rotation
Aggregate can be rotated 360˚
Gear Ratio
1:1.09
Swiveling Range
-100˚ to 100˚
Maximum Torque
17 ft. lbs
Spindle Direction
Opposite machine spindle
Maximum Temp.
185˚F
Spindle Outputs*
K1, K2
*See page 40 for spindle output specifications.
ER Collets sold separately. See pages 14 and 15 to select your ER collets.
37
Soft-Touch Floating Aggregate & Chip Guide System
The Soft-Touch
aggregate head accurately
follows the contours of your stock, automatically compensating for up to 10mm of variance. Floating pressure
is adjustable from 1/4 lb. to 20 lbs. Convenient tool
pre-setting flange allows you to perform fast, accurate
adjustments. Compressed air connection on the aggregate provides saw dust evacuation.
Aggregate comes with standard floating bell, ER 25 or
ER 32 output (your choice) and wrench. Options include
a variety of floating bells, shoes, and sleighs that are all
interchangeable.
Floating Aggregate with Chip Guide
IWF 2008 Challengers Award Finalist
Chip Guide System features
a rotor mounted at the tool,
which directs chips into
the machine’s dust exhaust
system. Chips don't contaminate your material so cutting
quality remains high.
See a video of the Chip Guide in action
at www.techniksusa.com/aggregate/cg
Function Line Soft-Touch Dimensions (mm)
12 g5
Function Line Soft Touch ( (grease lubricated)
18,000 RPM / 24,000 RPM
Floating Range
10 mm (with 10 mm adjustment)
Floating Pressure
adjustable from 1/4 lb. to 20 lbs
Rotation
aggregate can be rotated 360˚
Gear Ratio
1:1
Floating Bell**
70 mm deep X 105 mm I.D.
Maximum Torque
20 ft. lbs
Rotation Direction
same as machine spindle
Maximum Temp.
185˚F
Spindle Outputs***
M5, R6, R7, P1, Modular
*24,000 RPM for high speed and/or small cutting tools.
**Other bell diameters, lengths, and types available.
***Also ER 40, saw blade, and shrink-fit available.
See page 40 for spindle output specifications.
38
140
40
Spindle Speed Max.*
141.5 +10
185 -10
34
5
HSK center spindle
shown. Please specify
your machine spindle
and application.
35
Aggregate heads are configured to fit your spindle. Please call us at (800) 597-3921 for ordering assistance.
Smart Line Aggregates for Lighter Weight Routers
Smart Line aggregates are individually
hand-built just like our other aggregate lines. They
offer full aggregate functionality for standard duty
operations in a compact design for smaller routers.
Smart Line aggregates are grease lubricated and offer
an excellent price-to-performance ratio.
Smart Line Vario Adjustable Angle Type
All the features of the Function Line Vario, but sized
for lighter-duty applications. Comes with collet nut
and wrench.
Smart Line Duo
2 spindle output aggregate.
Dual spindle outputs are
great for boring and
sawing applications.
Smart Line Duo (grease lubricated)
Spindle Speed Max.
8,000 RPM
Tool Speed Max.
12,000 RPM
Rotation
Aggregate can be rotated 360˚
Gear Ratio
1:1.5
Maximum Torque
15 ft. lbs
Spindle Direction
one tool spindle same as
machine spindle, one opposite
Maximum Temp.
185˚F
Spindle Outputs*
M5, S1
See page 40 for spindle output specifications.
Smart Line Lockset Recess
Specially built for cutting lockset
recesses. Comes with collet nut
and wrench.
Smart Line Vario (grease lubricated)
Smart Line Lock Recess (grease lubricated)
Spindle Speed Max.
12,000 RPM
Tool Speed Max.
12,000 RPM
Spindle Speed Max.
8,000 RPM
Rotation
Aggregate can be rotated 360˚
Tool Speed Max.
12,000 RPM
Gear Ratio
1:1
Rotation
Aggregate can be rotated 360˚
Swiveling Range
0° to 100°
Gear Ratio
1:1.5
Maximum Torque
15 ft. lbs
Maximum Torque
4 ft. lbs
Spindle Direction
Same as machine spindle
Spindle Direction
Same as machine spindle
Maximum Temp.
185˚F
Maximum Temp.
185˚F
Spindle Outputs*
K1, K2
Spindle Outputs*
M5
See page 40 for spindle output specifications.
See page 40 for spindle output specifications.
ER Collets sold separately. See pages 14 and 15 to select your ER collets.
39
Modular System – Spindle Output Options
Note: Spindle outputs are designed to hold specific tools to perform a
variety of tasks. Some spindle outputs cannot be used with certain aggregates. Please contact us for help selecting your outputs. Call us toll-free
(800) 597-3921 or local (317) 803-8000.
R6 ER 32 collet and nut
Range: 3mm – 20mm
Modular spindle outputs (highlighted in blue boxes) are all interchangeable on the aggregates that support the modular spindle output system.
S1
Modular Saw Spindle
P1
Modular Saw Arbor
Range: 1.5mm-4mm tool shank
M5 Modular ER 25
07 Modular Arbor
R7 ER 40 - for Soft-Touch
Range: 4mm – 26mm
08 Modular Arbor
K1 ER 25 collet and nut
09 Modular Arbor
K2 Combi spindle, 45mm and
52mm bolt circle
R6 Modular ER 32
R7 Modular ER 40
M5 ER 25 collet and nut
R3 ER 16 collet and nut
Range: 1mm – 16mm
40
Range: 0.5mm – 10mm
W3
Weldon
DIN 1835 B ∅10H6
W4
Weldon
DIN 1835 B ∅12H6
ER Collets sold separately. See pages 14 and 15 to select your ER collets.
Spindle Output Options
S1 Saw Spindle, 45mm bolt circle
S2 Saw Spindle, 52mm bolt circle
01 Saw Spindle
UHM12030
P1
Prolock spindle
Range: 1.5mm-4mm tool shank
P2 Prolock spindle
Range: mm – 52mm
P3
Prolock spindle
Range: 98mm – 102mm
P4
Spindle for moulder head
Prolock spindle
Range: 28mm – 32mm
I3 ER 16 collet inside
P5 Prolock spindle
Range: 1mm – 10mm
I5 ER 25 collet inside
Range: 1mm – 16mm
Range: 28mm – 32mm
03 Special spindle ∅20h5
2x ∅6H7, 2x M6 - bolt circle 32mm
M10 centrical
05 Special spindle ∅20h6
2x ∅5H7, 2x M5 - bolt circle 32mm
M10 centrical
10 Special spindle ∅30
2x ∅6H7, 2x M5 - bolt circle 42mm
M10 centrical
12 Special spindle ∅30h5
2x M5 - bolt circle 45mm;
∅6H7, bolt circle 42mm
M10 centrical
13 Special spindle ∅30h5
2x M5 - bolt circle 45mm;
∅6H7, bolt
circle 42mm
M10 centrical
P6 Prolock spindle
Range: 28mm
– 32mm
All Techniks products are backed by our 100% satisfaction guarantee!
N1 Notch whistle
DIN 1835 E ∅6H5
41
Tool Holder Measuring Guide – Special Orders
Use this guide to help measure your tools to determine what you need to
order, or for special order toolholders built to your specifications.
Make and model of CNC router ______________________________________
Pull Stud Dimensions
P=
____________
A=
____________
L=
____________
R=
____________
Toolholder Dimensions
D=
____________
F=
____________
W=
____________
A=
____________
N=
____________
Make and model of HSK spindle CNC Router ______________________________________________
Toolholder Dimensions
D=
____________
F=
____________
W=
____________
A=
____________
N=
____________
42
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.
Woodworking Collets Measuring Guide
Use the guide below for selecting
your replacement collets. The best
way to tell what type of collet you
need is to measure the length of the
collet using a digital caliper. ER, TG,
and SYOZ collets all have unique
length and diameter measurements.
Standard Collet Dimensions
ER Collet Style
Length
O.D. (diameter)
ER 11
18mm (0.708")
11.5mm (0.45")
ER 16
27.5mm (1.08")
17mm (0.67")
ER 20
31.5mm (1.24")
21mm (0.83")
ER 25
34mm (1.34")
26mm (1.02")
ER 32
40mm (1.57")
33mm (1.3")
ER 40
46mm (1.81")
41mm (1.61")
ER 50
60 mm (2.36")
52mm (2.05")
DIN 6388 Collet Style
ER Collet Style
SYOZ Collet Style
Length
O.D. (diameter)
EOC 8
26mm (1.026")
14.4mm (0.567")
SYOZ 20
34mm (1.34")
20mm (0.78")
RDO 20
34mm (1.34")
20mm (0.78")
407E
34mm (1.34")
20mm (0.78")
EOC 12
34mm (1.34")
20mm (0.78")
SYOZ 25
52mm (2.06")
35mm (1.38")
RDO 35
52mm (2.06")
35mm (1.38")
462E
52mm (2.06")
35mm (1.38")
EOC 32
60mm (2.36")
43.7mm (1.72")
TG Collet Style
Length
O.D. (diameter)
TG 75
47mm (1.85")
27mm (1.06")
TG 100
60mm (2.36")
35mm (1.38")
Special Order Collets Dimensions
Length __________ Diameter ___________ Other Markings__________
Length __________ Diameter ___________ Other Markings__________
TG Collet Style
Length __________ Diameter ___________ Other Markings__________
Special Pull Studs
We can get the pull studs you need. Just fill in your pull
stud(s) dimensions on the chart below before you call.
Keep your information in this catalog for easy re-orders.
Please carefully select the pull stud you need by referring
to the diagram.
For safe operation please make sure that the pull stud you
order is the exact pull stud your machine uses. Improper
choice of pull stud can cause damage to the spindle and/
or toolholder, and is a potential safety hazard.
Stud
Machine
d1
d2
D
d3
d2
d1
T
l1
I1
l2
I2
All Techniks products are backed by our 100% satisfaction guarantee!
θ
T
43
Part Number Index: 00100 – 04220-7/32
Part No.
Pg.
Part No.
Pg.
Part No.
00100
00151
00152
00153
00156
00157
00158
00159
00160
00165
00166
00167
00168
00170
00300
00316-SLN-L
00316-SLN-R
03508
03508-1/4
03508-1/8
03508-3/16
03508-5/16
03520
03520-1/2
03520-1/4
03520-1/8
03520-10
03520-3/16
03520-3/8
03520-5/16
03520-7/16
03531-1/2
03531-1/4
03531-1/8
03531-10
03531-16
03531-3/16
03531-3/8
03531-5/16
03531-5/8
03531-7/16
03531-9/16
03636
03638
03690-25
03691
03868-1
03868-1/2
03868-1/4
03868-1/8
03868-10
03868-16
03868-20
03868-25
03868-3/16
03868-3/4
03868-3/8
03868-5/16
03868-5/8
03868-7/16
03868-7/8
03868-9/16
04008 - 1/2
04008 - 1/4
11
11
11
11
11
11
11
11
11
11
11
11
11
11
11
9
9
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
29
28
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
23
20
20
04008 - 1/8
04008 - 11/16
04008 - 11/32
04008 - 13/32
04008 - 15/32
04008 - 17/32
04008 - 19/32
04008 - 21/32
04008 - 23/32
04008 - 3/16
04008 - 3/32
04008 - 3/4
04008 - 3/8
04008 - 5/16
04008 - 5/32
04008 - 5/8
04008 - 7/16
04008 - 7/32
04008 - 9/16
04008 - 9/32
04010 - 1
04010 - 1/2
04010 - 1/4
04010 - 1/8
04010 - 11/16
04010 - 11/32
04010 - 13/16
04010 - 13/32
04010 - 15/16
04010 - 15/32
04010 - 17/32
04010 - 19/32
04010 - 21/32
04010 - 23/32
04010 - 25/32
04010 - 27/32
04010 - 29/32
04010 - 3/16
04010 - 3/32
04010 - 3/4
04010 - 3/8
04010 - 31/32
04010 - 5/16
04010 - 5/32
04010 - 5/8
04010 - 7/16
04010 - 7/32
04010 - 7/8
04010 - 9/16
04010 - 9/32
04018
04018-TWA
04208 - 01.0
04208 - 01.5
04208 - 02.0
04208 - 02.5
04208 - 03.0
04208 - 03.5
04208 - 04.0
04208 - 04.5
04208 - 05.0
04211 - 01.0
04211 - 01.5
04211 - 02.0
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
20
28
29
15
15
15
15
15
15
15
15
15
15
15
15
04211
04211
04211
04211
04211
04211
04211
04211
04211
04211
04211
04211
04211
04211
04211
04211
04211
04216
04216
04216
04216
04216
04216
04216
04216
04216
04216
04216
04216
04216
04216
04216
04216
04216
04216
04216
04216
04216
04216
04220
04220
04220
04220
04220
04220
04220
04220
04220
04220
04220
04220
04220
04220
04220
04220
04220
04220
04220
04220
04220
04220
04220
04220
04220
44
-
Pg.
02.5
03.0
03.5
04.0
04.5
05.0
05.5
06.0
06.5
07.0
1/16
1/4
1/8
3/16
3/32
5/32
7/32
01
02
03
04
05
06
07
08
09
1/16
1/4
1/8
10
11/32
13/32
3/16
3/32
3/8
5/16
5/32
7/32
9/32
02
03
04
05
06
07
08
09
1/2
1/4
1/8
10
11
11/32
12
13
13/32
15/32
3/16
3/32
3/8
5/16
5/32
7/16
7/32
15
15
15
15
15
15
15
15
15
15
14
14
14
14
14
14
14
15
15
15
15
15
15
15
15
15
14
14
14
15
14
14
14
14
14
14
14
14
14
15
15
15
15
15
15
15
15
14
14
14
15
15
14
15
15
14
14
14
14
14
14
14
14
14
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.
Part Number Index: 04220-9/32 – 06102
Part No.
04220
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04225
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
04232
-
9/32
02
03
04
05
06
07
08
09
1/2
1/4
1/8
10
11
11/32
12
13
13/32
14
15
15/32
16
17/32
19/32
3/16
3/32
3/8
5/16
5/32
5/8
7/16
7/32
9/16
9/32
03
04
05
06
07
08
09
1/2
1/4
1/8
10
11
11/16
11/32
12
13
13/32
14
15
15/32
16
17
17/32
18
19
19/32
20
21/32
23/32
3/16
Pg.
Part No.
Pg.
Part No.
Pg.
14
15
15
15
15
15
15
15
15
14
14
14
15
15
14
15
15
14
15
15
14
15
14
14
14
14
14
14
14
14
14
14
14
14
15
15
15
15
15
15
15
14
14
14
15
15
14
14
15
15
14
15
15
14
15
15
14
15
15
14
15
14
14
14
04232 - 3/32
04232 - 3/4
04232 - 3/8
04232 - 5/16
04232 - 5/32
04232 - 5/8
04232 - 7/16
04232 - 9/16
04232 - 9/32
04232 -7/32
04240 - 04
04240 - 05
04240 - 06
04240 - 07
04240 - 08
04240 - 09
04240 - 1
04240 - 1/2
04240 - 1/4
04240 - 1/8
04240 - 10
04240 - 11
04240 - 11/16
04240 - 11/32
04240 - 12
04240 - 13
04240 - 13/32
04240 - 14
04240 - 15
04240 - 15/32
04240 - 16
04240 - 17
04240 - 17/32
04240 - 18
04240 - 19
04240 - 19/32
04240 - 20
04240 - 21
04240 - 21/32
04240 - 22
04240 - 23
04240 - 23/32
04240 - 24
04240 - 25
04240 - 26
04240 - 3/16
04240 - 3/4
04240 - 3/8
04240 - 5/16
04240 - 5/32
04240 - 5/8
04240 - 7/16
04240 - 7/32
04240 - 7/8
04240 - 9/16
04240 - 9/32
04576
04577
04578
04580-16
04580-20
04587
04588-R
04601-16
14
14
14
14
14
14
14
14
14
14
15
15
15
15
15
15
14
14
14
14
15
15
14
14
15
15
14
15
15
14
15
15
14
15
15
14
15
15
14
15
15
14
15
15
15
14
14
14
14
14
14
14
14
14
14
14
29
29
29
29
29
29
29
29
04602-20
04603-25
04604-32
04605-40
04608
04609
04610
04613
04614
04615
04616
04617
04618
04620
04621
04622
04623
04624
04888
04889
04891
04893
04894
04895
04896
04897
04898
05.024.001
05.024.002
05.024.003
05.024.004
05.024.005
05.024.006
05.024.012
05.024.013
05.024.014
05.024.015
05.024.016
05.024.018
05.024.020
05.024.114
05.024.116
05.024.118
05.024.120
05.024.122
05.024.126
05.024.130
05.024.131
05.024.132
05.024.133
05.024.134
05.024.135
05.024.136
05.024.137
06000-2016M
06000-2016MC
06000-2516
06000-2520
06001
06001-W
06010
06101
06101-SLOTNUT
06102
29
29
29
29
28
28
28
28
28
28
28
28
28
28
28
28
28
28
7
7
7
7
7
7
7
7
7
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
13
5
5
5
5
7
7
7
6
6
6
All Techniks products are backed by our 100% satisfaction guarantee!
45
Part Number Index: 06102-C – 1116.0300
Part No.
Pg.
Part No.
06102-C
06102-DNA
06102-SLOTNUT
06103
06103-SLOTNUT
06104
06104-SLOTNUT
06105
06105-SLOTNUT
06106
06106-SLOTNUT
06107
06107-SLOTNUT
06108-2.5
06108-2.5-SLOTNUT
06109
06110
06111
06111-90
06112
06113
06113-W-60
06113-W-60-A
06113-W-90
06114
06115
061-BT35-ER 32 76
061-BT35-ER 32 76A
07710
07711
07801
07803
07806
07808
07812
07814
08516 - 03.5
08516 - 04.0
08516 - 04.5
08516 - 05.0
08516 - 05.5
08516 - 06.0
08516 - 06.5
08516 - 07.0
08516 - 07.5
08516 - 08.0
08516 - 08.5
08516 - 09.0
08516 - 09.5
08516 - 10.0
08520 - 03.5
08520 - 04.0
08520 - 04.5
08520 - 05.0
08520 - 05.5
08520 - 06.0
08520 - 06.5
08520 - 07.0
08520 - 07.5
08520 - 08.0
08520 - 08.5
08520 - 09.0
08520 - 09.5
08520 - 10.0
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
7
7
7
7
7
7
7
7
7
27
08520
08520
08520
08520
08520
08520
08525
08525
08525
08525
08525
08525
08525
08525
08525
08525
08525
08525
08525
08525
08525
08525
08525
08525
08525
08525
08525
08525
08525
08525
08525
08525
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
08532
46
25
25
25
25
25
25
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
-
10.5
11.0
11.5
12.0
12.5
13.0
03.5
04.0
04.5
05.0
05.5
06.0
06.5
07.0
07.5
08.0
08.5
09.0
09.5
10.0
10.5
11.0
11.5
12.0
12.5
13.0
13.5
14.0
14.5
15.0
15.5
16.0
03.5
04.0
04.5
05.0
05.5
06.0
06.5
07.0
07.5
08.0
08.5
09.0
09.5
10.0
10.5
11.0
11.5
12.0
12.5
13.0
13.5
14.0
14.5
15.0
15.5
16.0
16.5
17.0
17.5
18.0
18.5
19.0
Pg.
Part No.
Pg.
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
08532 - 19.5
08532 - 20.0
08540 - 04.0
08540 - 04.5
08540 - 05.0
08540 - 05.5
08540 - 06.0
08540 - 06.5
08540 - 07.0
08540 - 07.5
08540 - 08.0
08540 - 08.5
08540 - 09.0
08540 - 09.5
08540 - 10.0
08540 - 10.5
08540 - 11.0
08540 - 11.5
08540 - 12.0
08540 - 12.5
08540 - 13.0
08540 - 13.5
08540 - 14.0
08540 - 14.5
08540 - 15.0
08540 - 15.5
08540 - 16.0
08540 - 16.5
08540 - 17.0
08540 - 17.5
08540 - 18.0
08540 - 18.5
08540 - 19.0
08540 - 19.5
08540 - 20.0
08540 - 20.5
08540 - 21.0
08540 - 21.5
08540 - 22.0
08540 - 22.5
08540 - 23.0
08540 - 23.5
08540 - 24.0
08540 - 24.5
08540 - 25.0
08540 - 25.5
08540- 03.5
1016.0030
1016.0040
1016.0050
1016.0060
1016.0080
1016.0100
1016.0120
1116.0014
1116.0018
1116.0038
1116.0125
1116.0150
1116.0175
1116.0200
1116.0225
1116.0250
1116.0300
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
26
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
24
Call us toll-free at: (800) 597-3921 to speak to a tool holder applications specialist.
Part Number Index: 1116.0316 – TSHG1-63F-46
Part No.
Pg.
Part No.
Pg.
Part No.
Pg.
1116.0316
1116.0350
1116.0400
1116.0450
1116.0500
1116.0600
1116.0700
1116.0800
1116.0900
1116.1000
12000-CMS
12040-CMS
12213-W-50
12213-W-63
12213-W-90
12215-W-57
12261-W
12407-W
12700-100-W
12700-40-W
12700-55-W
12700-80-W
13001
13001-45
13003
13003
171.05.008.001
171.05.008.002
171.05.036.016
171.05.036.018
171.05.036.020
171.05.036.035
171.05.046.003
171.05.071.010
171.05.071.011
171.05.071.250
171.05.071.375
171.05.071.500
171.05.071.750
171.05.072.1
17706
17707
17708
17906-2
200 TH
2016-200
21225
21240
21325
21332
21340
22220
27116
27116-30
27116-40
27116-45
27116-50
27116-55
27116-60
27116-65
27216
27500
28110
28210
24
24
24
24
24
24
24
24
24
24
5
5
5
5
5
5
5
5
8
8
8
8
25
25
25
25
4
4
12
12
12
12
9
10
10
10
10
10
10
10
27
27
27
31
29
24
18
18
19
19
19
28
24
24
24
24
24
24
24
24
24
21
21
21
29132
29827
29828
300 TH
30000
30001
30002
30005
31025F
31374-60
33108
33111
33116
33120
33125
33125-L
39.05.046.001
41060
41080-3H
41085
41087
41616
41620
41625
41632
41640
4403502
46111
46116
46120
46125
46132
46140
49019
50001
54-212-012
60 TH
64.05 071.625
64.05 071.750
64.05.043.224
64.05.043.225
64.05.046.051
64.05.071.250
64.05.071.375
64.05.071.500
67.05.046.001
750-19
84.05.008.001
84.05.008.002
84.05.008.003
85.05.008.002
86.05.008.002
86.05.008.003
894-22
CMS-RR32
DC32-1/2
DC32-1/4
DC32-3/16
DC32-3/4
DC32-3/8
DC32-5/16
DC32-5/8
DNA16-TWA
DNA16-TWA
18
29
29
29
4
4
4
4
4
4
18
18
18
18
18
18
9
8
8
8
8
19
19
19
19
19
25
17
17
17
17
17
17
25
4
31
29
10
10
12
12
9
10
10
10
9
25
4
4
4
4
4
4
24
9
27
27
27
27
27
27
27
24
29
DNA16W
NT-54300130
NTS-40 Taper
NTS-BT30-38
NTS-BT30-41
NTS-BT30-Slot
NTS-HSK63A
NTS-HSK63F-36
NTS-HSK63F-38
NTS-HSK63F-41
NTS-HSK63F-46
NTS-ISO20-17
NTS-ISO20-22
NTS-ISO25-27
NTS-ISO30-36
NTS-ISO30-38
NTS-ISO30-47
PSS - 30BT
PSS - 30ISO
PSS - 40
PSS - 50
PSSC - 50
SD-20mm-.250
SD-20mm-.312
SD-20mm-.375
SD-20mm-.500
SD-20mm-.625
SD-20mm-Nut
SD-C001-.125
SD-C001-.187
SD-C001-.250
SD-C001-.312
SD-C001-.375
SD-C001-.500
SD-C001-Nut
SD-C015-.125
SD-C015-.250
SD-C015-.312
SD-C015-.375
SD-C015-.500
SD-C015-.625
SD-C015-.750
SD-C015-Nut
SD-TWA
SS-22-1/2
SS-22-1/4
SS-22-10
SS-22-3/8
SS-22-Ext -Nut
SS-22-Nut
TE-171.05.071.500-S
TE-64.05 071.750-S
TE-64.05.071.500-S
TSHG1-30-36
TSHG1-30-38
TSHG1-30-41
TSHG1-30-47
TSHG1-40-BT
TSHG1-40-CT
TSHG1-63F-36
TSHG1-63F-38
TSHG1-63F-46
24
5
30
30
30
30
30
30
30
30
30
30
30
30
30
30
30
29
29
29
29
29
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
22
29
22
22
22
22
22
22
10
10
10
30
30
30
30
30
30
30
30
30
All Techniks products are backed by our 100% satisfaction guarantee!
47
Tools cut smoother, faster, & safer when you tighten
collets, nuts, and retention knobs to correct specifications.
Torque Chart
Collet Nuts
Wrench Type
Max. Torque
Rec. Torque*
Wrench
Slotted
50 ft/lbs
45 ft/lbs
41916
Hex
50 ft/lbs
45 ft/lbs
41116
Slotted
75 ft/lbs
67 ft/lbs
41920
Hex
75 ft/lbs
67 ft/lbs
41120
ER 25 Spanner
Slotted
95 ft/lbs
85 ft/lbs
41925
ER 25 M
Castle
29 ft/lbs
25 ft/lbs
23125
ER 32 Spanner
Slotted
125 ft/lbs
112 ft/lbs
41932
ER 40 Spanner
Slotted
140 ft/lbs
126 ft/lbs
41940
SYOZ 25
Hook
100 ft/lbs
90 ft/lbs
03638
TG 75
Hook
100 ft/lbs
90 ft/lbs
27500
TG 100
Hook
100 ft/lbs
90 ft/lbs
28110
ER 16
ER 16 Hex
ER 20
ER 20 Hex
1. Snap collet into nut.
2. Insert cutter into collet
3. Hand tighten collet nut
assembly into tool holder
4. Insert tool holder
assembly into tightening
fixture and secure it.
5. Tighten collet nut to
recommended torque
using a torque wrench.
Retention Knobs
Wrench Flats
Drive
Max. Torque
Rec. Torque*
BT 30 Taper
0.535"
1/4"
40 ft/lbs
36 ft/lbs
ISO 30 Taper
0.535"
3/8"
40 ft/lbs
36 ft/lbs
Any 40 Taper
0.750"
3/8"
85 ft/lbs
76 ft/lbs
BT 50 Taper
1.187"
1/2"
110 ft/lbs
99 ft/lbs
CAT 50 Taper
1.250"
1/2"
110 ft/lbs
99 ft/lbs
Recommended torque is 80-90% maximum torque value.
Use a tightening fixture and torque
wrench to make sure tools are
properly tightened. Incorrect
torque can cause cracked collets, poor cutting performance,
and possibly cause tools to
come loose during operation,
causing a very dangerous
work environment.
Ph. (800) 597-3921 • Fax (877) 776-9994
E-mail: info@techniksusa.com, website: www.techniksusa.com
9930 East 56th St., Indianapolis, IN 46236
Office Hours: Monday – Friday 8:00 am to 5:00 pm, EST.
© June, 2008, Techniks Inc., Indianapolis, Indiana USA,
LITCNC2008